Tag Archives: Witch’s Brew (Leelanau Cellars)

2015/10/27 (T) The Pilot’s Seat

Leave a reply

My morning started at 8 AM in its usual fashion.  I fed the cats, made coffee, started a load of laundry, made/ate breakfast (orange/grapefruit juice and granola with fresh blueberries), drank my coffee in the living room with the fireplace on and Jasper at my side, day-dreamed about high quality used Sony alpha lenses, and finally got to work on the bus a little after 10 AM.  Rain is coming tonight and forecast to stick around into Thursday so today would be a good day to do some more trimming, felling, and cutting up of dead trees.  The temperature this morning was still in the 40’s, however, and there is still much to be done in the bus.

A few days ago I installed a new AC outlet on the forward side of the cabinet behind the driver’s seat.  I wired it into the outlet on the aft side of the cabinet and then discovered that the original outlet was cracked.  I had also used an oversized cover plate on the new outlet and it interfered with the Corian cabinet top.  I finally got around to replacing the cracked outlet this morning.  I also switched the cover plates.  The regular size one still interfered slightly with the Corian top so I cut 1/8″ off of the top edge and added strips of felt on the three edges of the cabinet to raise the Corian top slightly and cushion it.  Everything fit nicely.  I turned the circuit breaker on and checked for power.  The outlets were good to go and I checked this mini-project off my (mental) project list.

I took a break and called the Escapees RV Club to register Linda and me as staff for the July 2016 Escapade.  I then called Josh at Coach Supply Direct regarding extra brackets for our MCD shades/brackets, the wiring of the passenger seat switch, and the correct orientation of the swivel bearings.  I learned that the flange, which wraps around the other piece on the inside of the ring, goes down.  (I had puzzled out that it should go the other way so I am glad I asked.)  When I was done with my phone calls I had a quick lunch of Sabra Roasted Red Pepper Hummus and Snyder sourdough pretzel nibblers.

My next task was unbolting the driver seat pedestal base from the floor.  The pedestal is secured by four large carriage bolts that go through holes at the four corners of the base plate and thread into nuts that I presume are welded into the floor structure.  The base had to be removed in order to remove the old vinyl floor tile which was installed under the base.  To get the old tile out I also had to remove a plastic cover around the steering linkage and a floor mounted bracket that retained the bottom if it.  Last, but not least, I had to unscrew the accelerator bracket from the floor by removing three small lag screws.  The accelerator is electrical, with a cable that runs through the floor, but other than limited access it was easy to detach.

Removing the old vinyl tile from the driver’s area of the cockpit was relatively straightforward.  It’s somewhat flexible and wasn’t glued down that tightly.  When Creative Mobile Interiors installed the tile they laid it out in a way that allowed the pieces to be trimmed in reasonable ways to fit around the steering column and brake pedal.  The brake pedal is mechanically linked to a complex multi-port air valve in the compartment under the floor and any finished floor has to be installed around it.

The plywood under the driver’s seat area was depressed directly under the base.  It seemed unlikely that this was the result of the base being bolted down.  It may indicate that this area also got wet like the area under the passenger side seat base.  I plan to install SurePly underlayment on the floor under the passenger seat but not the under the driver’s seat so I will either have to replace this piece or use floor leveling compound to fill the depressed area.  Replacing the plywood is probably the correct, but more involved, solution.

I started thinking about installing the new tile so I laid out all of the old tiles on the floor in the garage, kind of like putting a simple jigsaw puzzle back together.  I plan to use them as a pattern to cut the new tiles.  With a clear view of the whole driver’s area I became intrigued by the lower sidewall counsel next to the driver’s seat.  The more I looked at it the clearer it became that Royale Coach had cut the top off of a bumped out area, removed the upper three inches of the wall of the bump out, replaced the top piece, and tried to fill in the three inch gap in the side wall.  They had also cut out an access plate and then screwed it back in.  It eventually became obvious to me that they had done this to create horizontal space for the wide Villa driver’s seat that was in the coach when we bought it.  Had Royale Coach left the ISRI seat in place these modifications would not have been needed.  They were originally hidden under carpet but once the carpet was removed the really poor quality of the workmanship in this area was all too apparent.

I probably should have applied adhesive remover to the stairs and walls around the cockpit but it has to sit for 1 to 3 hours and the timing wasn’t right.  The weather was still decent and I needed to finish working on the trees at the west end of our property.  The adhesive remover can be left on for up the 24 hours so applying it at 5 PM with the intent of removing it the next morning might be ideal.  The weather forecast for overnight, through tomorrow, and into Thursday, however, is for rain and colder temperatures, so they will not be good mornings for working with the door of the bus open.

Around 3:30 PM I had a banana nut muffin and then called Phil at Precision Grading.  I got his voice mail and left him a message.  I was getting ready to use the chainsaw to cut down a small dead tree at the west end of the property when Linda texted that she was leaving the bakery.  A few minutes later Chuck called.  He had some carpet remnants for us and was nearby so he came over.  He could not stay long but took the time to look at what I was working on in the bus before he left.  It would still be awhile before Linda got home so I took the chainsaw to the west end of the yard, cut down the tree, de-limbed it, and cut it up into manageable size pieces.  I then cut up another tree of similar size that has been on the ground for a while and cut up some of the larger branches that I trimmed off the trees yesterday.

Linda got home while I was finishing the tree work and started fixing squash and a lentil/quinoa pilaf for dinner, both of which would take some time.  After cleaning the saw and putting it away I took one of the carriage boots from the bus driver’s seat and went to Lowe’s to see if I could find slightly longer replacements.  The old ones were somewhat rusted and some of the threads were in less than ideal condition.  The new Armstrong vinyl tiles are also a bit thicker than the old ones and I wanted to make sure I had bolts that were long enough to completely thread into the retained nuts.  It turned out that the bolts are metric, specifically M12-1.75×80.  Lowe’s had Grade 8 M12-1.75×90 bolts (10 mm longer than the 80s) so I bought four.  I also bought some thick M12 fender washers that were larger than the old ones.  While I was there I picked up a role of red electrical tape.

Dinner was excellent.  The squash was baked without butter (vegan) or brown sugar but was very tasty.  The pilaf had onions, garlic, and mixed greens and was very good.  We finished the Witch’s Brew wine from Leelanau Cellars that Linda used to poach the pears on Saturday.  The squash did not look that big, but neither of us was able to finish our half so we saved it for tomorrow’s lunch.

I checked e-mail after dinner and then we settled in to watch our Tuesday night TV programs.  We caught the weather report at 11 PM and then turned off the television and lights.  I turned down the brightness on my iPad display and worked for another 30 minutes before going to sleep.  I did not hear back from Phil this evening but I already knew he would not be here on Wednesday if the rain came as forecast as he had another job to work on that was better suited to working in rainy conditions than ours.

 

2015/10/24 (S) Meghan and Chris

Leave a reply

We drove separately to our SLAARC breakfast in South Lyon as Linda had plans to walk with Diane at Kensington Metropark after breakfast.  We drove through some heavy rain after which I chatted a bit with Tom (W8TAF) and Mike (W8XH).  As always, we enjoyed the breakfast conversation with our fellow amateur radio operators.  Linda left at 9:15 and I lingered until 9:30 enjoying my last cup of coffee.  I paid our check and had just headed for home when Mike (W8XH) called me on the radio.  We had a good chat about my Hi-Q 6-80 mobile HF antenna and will try to find a time to test it using his newer VNWA.  Mike has learned a lot about how to use it in the last couple of years and is always willing to put that knowledge to use to help his fellow ham.  I would love to figure out a way to mount this antenna so we can take it with us this winter and use it, but I doubt that will happen.  We just have too much else that has to get done in the next month that is more important than this.

At home I pulled up the DX Engineering website on my iPad.  I found their Mix 31 snap-on ferrite chokes and put them in my cart.  If I can find a few other small things to buy the order will qualify for free shipping.  I suspect that will not be a problem.

Next I pulled up the Sony alpha app and researched the acronyms they use for various features of their cameras and lenses.  The model numbers for their A-mount lenses all begin with SAL (Sony “A” Lens) and their E-mount lenses all begin with SEL (Sony “E” Lens) so that helps sort those out right up front.  However, they make both 35mm full frame (36mm x 24mm) and APS-C (24mm x 16mm) lenses in both mounting systems.  The FF lenses can be used on APS-C bodies, such as our Sony a100, but the APS-C lenses, which always include the letters “DT” in the product name, cannot generally be used on FF bodies.  Our new Sony SLT-a99v DSLT camera body, however, can detect a DT lens and automatically limits the active portion of the sensor to an APS-C size area.

SAM stands for “Smooth Action Motor” and SSM stands for “SuperSonic wave Motor” both of which are used with certain lenses, especially large telephoto ones, that have their own internal focusing motor.  OSS stands for “Optical Steady Shot.”  Even though the alpha series cameras have image stabilization built into the body some Sony lenses also have image stabilization built into them.

One of the things I was trying to find out is which lenses have distance encoders so they will work with the ADI (Advanced Distance Integration) feature of the a99 body and compatible Sony flash units.  The lens specification table in the alpha app was not really clear on this point.  Some lenses were marked with a small circle for this feature and others with a dash.  If their nomenclature is consistent with other entries the dash means “no”.  Logically then the circle means “yes” but I did not pursue this further.  I will have to experiment with the 18-70mm APS-C format lens that came with the a100 and see if it supports ADI.

I opened the B&H Photo Video app and revisited the reviews on the Sony HVL-60m flash.  Although more expensive than the HVL-43m I added it to my cart.  Besides being more powerful it has an available external battery pack which I found and also put in the cart.  Finally, I added the Cotton Carrier dual camera harness to the cart.  I found my Minolta electric shutter releases and checked to see if they worked with the alpha 99.  They did!, so I did not need to order new ones.  B&H was closed for online order processing until 7:30 PM this evening so I did not submit the order right away.  The Cotton Carrier is on sale until the 26th so I will submit the order tomorrow while the sale price is still valid.

Linda got home at 12:30 PM and we had the last two vegan hotdogs for lunch.  She then started preparing dinner and I went to my office.  I did a load of laundry, dealt with e-mail, checked in with RVillage, and copied photos from both the Sony a100 and the Sony a99 to my computer.  I updated my BCM article spreadsheet and then moved article folders to the proper directories and deleted them from my BCM Dropbox folder.  I added 80 pounds of solar salt to the water softener and then brought the laundry upstairs and hung it up.  By 4:30 PM I was feeling very tired and took a short nap until Meghan and Chris showed up at 5 PM.

We showed them the driveway and bus projects and then went inside the house just as it started to sprinkle.  Everyone selected a beer and we were standing around the kitchen when a brief, but very intense, line of storms moved through our area with heavy rain and strong winds.

For dinner Linda made a salad of dark leafy greens with tomatoes, carrots, mushrooms, and raisins dressed with a raspberry vinaigrette.  The main course was a Farro pilaf with dried cranberries, onions, garlic, broccoli leaves, and slivered almonds.  Yes, broccoli leaves.  The whole broccoli plant is edible but until recently only the flowerets were available in stores.  The side dish was Brussels sprouts cut in half and oven-roasted with salt, pepper, and a little olive oil.  Dessert was pears in wine.  She used the Witch’s Brew, a spiced red wine that was perfect for this dish and this time of year.  After poaching the pears she reduced the wine to a sauce and chilled everything in the refrigerator for hours.  (The pears were made ahead of time as was the Farro, with the main dish being finished just before serving.)

We sat in the living room with the fireplace on and chatted about houses, pets, travel, sports, and the upcoming holidays.  Meghan and Chris stayed until 8:30 PM and then headed home.  It was a nice visit during which both cats actually came out of hiding and allowed themselves to be petted, a rare treat in Jasper’s case.

We were both tired, partly the residual effect of our altered schedule on Wednesday and Thursday, so we finished clearing the table and went to bed.  The Detroit PBS Create channel was featuring vegetarian (including vegan) episodes of various cooking shows so we watched a few of those before turning off the TV and going to sleep.

 

20141030-1102 Fixing Buses in Indiana

Leave a reply

2014/10/30 (R) To Kokomo We Go

Well…sort of.  Our actual destination was Maple Grove Distributors in Galveston, Indiana, which was in the general direction of Kokomo, but not as far.  (It’s pronounced “gal VES ten” with the emphasis on the second syllable.)  The tie rod ball ends that Butch ordered had finally come in and he wanted to get them early this morning so that: 1) We could get back and take advantage of a relatively nice late October day, and 2) He would have them for tomorrow when the weather is forecast to be lousy and thus a good day for inside work such as fabricating ride height linkages.

PS rear corner bedroom cabinet with slot in door for TV/monitor wires.

PS rear corner bedroom cabinet with slot in door for TV/monitor wires.

In spite of the nice weather I spent most of the day working inside my bus, stopping occasionally to help Butch with something.  I don’t have a lot of outside projects at the moment, or at least none that I felt like working on, and I really wanted to get the bedroom TV cabinet taken care of.  As with the front TV cabinet that I worked on for the last couple of days, the bedroom cabinet once housed a 19″ CRT TV set and a VHS tape deck.  I removed those in late 2011 while the bus was at Phoenix Paint and had Jaral Beaty make doors to cover the openings.  Once those doors were installed, I mounted 22″ diagonal, 16:9 aspect ratio, LCD/LED flat panel TV/monitors on each door. The power and signal connections, however, were inside the cabinets, so for the last couple of years the cables have come out of the bottom/rear of the TVs and under the bottom edge of the doors and into the cabinets.  This arrangement prevented the doors from being closed, even though they had spring loaded ball catches, so we have held them closed with a couple of pieces of bright green Frog Tape.  The tape is sticky enough to hold the door closed but does not seem to leave any reside even after being in place for a while.

The wires from the TV/monitor pass through the slot in the door so the dorr can be closed and latched.

The wires from the TV/monitor pass through the slot in the door so the dorr can be closed and latched.

As with the front TV cabinet door, I created a horizontal slot behind the TV, positioned to allow the cables to come down out of the back of the TV and bend gently through to the inside of the cabinet.  I removed some unneeded cable and coiled up other cables and secured them with zip ties that have a mounting tab with a hole for a screw.

My two outside projects were brief.  I got back under the front of the bus between the front tires and unbolted the ride height linkage.  It unbolted from the ride height valve lever arm easily but not from the axle bracket.  Fonda got a can of Cyclo Breakaway and some paper towels for me, but even after spraying the nut and letting it sit it would not come loose.  I am not the strongest guy in the bus yard so I put some more muscle into it and broke the bolt off with the nut still stuck tight to it.  The other half of the bolt then slide out easily.

As long as I had my wrenches out I slide under the rear end of the bus to see if I could free a couple of wires for the auxiliary braking system that were pinched under a mounting pad for the rear bumper fascia.  The stud had a Nylok nut on it that was barely threaded onto the stud.  The reason, I guessed, was the stud was at an angle that made it difficult to get a socket and ratchet on it.  I was able to loosen/tighten it using a universal (swivel) adapter between the socket and the ratchet.  While I was under there I noticed a second stud with a barely threaded Nylok so I tightened it as well.  One of the things you have to watch out for on a used RV is all the work that other people have done ‘just well enough’ to get it ‘out the door’ without something falling off in the parking lot.  These are always things that are hidden and relatively inaccessible, which is why they were not done correctly or completely in the first place, but the assumption is you will never see them.

My other inside project was to separate the load wires for the lighted entrance handle and the patio light and put them on separate switches.  It turned out that the front most switch just inside the entrance door (next to the passenger seat) was supplying 12VDC power to three circuits, the two just mentioned and a third one that, as of this writing, is still a mystery in that I was unable to determine anything that was being controlled by those wires.  The first (front) switch now controls only the lighted entrance handle, the second (middle) switch controls only the patio light, and the third (rear) switch controls…well, I don’t know what it controls but it definitely puts 12VDC power onto a wire that goes somewhere.

I assisted Butch briefly in locating their front fan-coil heat exchanger relative to the bay where the coolant lines will go.  Later in the day I helped him position the front suspension of their coach to the MCI specified spacing for the air springs so he can fabricate the ride height linkage to the correct length.

I needed a few parts for projects I might want to work on tomorrow so I left at 7 PM and drove to the Home Depot in Logansport.  That also gave me a chance to call Linda and chat about cell phone data plans.  I got back to Twelve Mile at 8:30 PM.  Butch and Fonda were already having their dinner so I went to my bus and made a salad.  After I cleaned up the day’s food utensils I installed the 6-outlet surge protected adapter in the AC duplex outlet in the bedroom TV cabinet.  That completed my work for the day and I returned to the house, visited briefly, and retired to my room to check e-mail, offload photo files from my camera, and write this post.

2014/10/31 (F) Boo! Snow (Boo)

After a relatively mild October the weather decided to turn more seasonable just in time for Halloween.  I was originally going to title this post “Foot Pounds and Gigabytes” but decided to acknowledge All Hallows’ Eve instead, along with the dramatic change in the weather.

A couple of days ago I bought a torque wrench from Butch that is adjustable up to 600 foot pounds, which is the kind of torque needed to tighten and loosen the lug nuts on our bus wheels.  It’s a very big torque wrench; over three feet long.  I need to buy a compatible socket to go with it.  Today was also the last day for the Verizon and AT&T double your data plan promotions, so I planned my day to put me in Elkhart, Indiana while one of the corporate stores was still open.

I got up around 8 AM and spent 45 minutes doing some preliminary packing after which I went out to my coach and had breakfast.  We had snow flurries around 9 AM this morning and did not work outside today save the few minutes I spent adjusting the air pressure in the tires of my Honda Element.  Today was mostly about shopping.

I got a cup of coffee from Small Town Brew and then we headed to Logansport where we did most of our usual circuit:  NAPA Auto Parts, O’Reilly’s Auto Parts, Rural King, Aldi’s, and Walmart.  (The only regular place we did not go was Home Depot.)  My only purchase was a 12VDC dual outlet with a mounting flange that I found at O’Reilly’s.  I plan to use it to create power connections for the GPS and TPMS receiver.  (I realized later that I should have bought three of them as I also need to supply power to the DVD camera/recorder up front and the TPMS repeater which I plan to mount in the rear TV cabinet.)

We got back around noon and I spent the next couple of hours straightening up the inside of the bus and packing everything that was going home with me.  Around 2:45 PM I finished packing the stuff I had in the guest bedroom and began loading the car.  I wrote up a list of things we owed each other money for and, as I expected, I owed Butch more than he owed me.  (He tends to order things we need on his accounts and I pay him back.)  I bought a Variac from him, added it to the list, and put it in the car.  Fonda has been working on a wedding dress for their daughter Gene for quite some time and was done except for some trim, so I got to see it before I left, which I did at 3:15 PM.  It was very nice.

I had located a Verizon corporate store on US-33 just south of US-20 which was on my normal route home.  I arrived at that intersection around 4:45 PM and first stopped at the Burger King next door for some French Fries.  The Verizon sales associate, Hector, claimed to know nothing about the double data promotion and insisted there was no such thing available.  I called Linda from their parking lot and we discussed what to do as today was the last day for the promotion.  She had checked our account online last night, and although we could change our monthly data allowance online (for a price, of course) there was no information about the promotion available there either.  Very strange considering how much this has been in the media all month.

Linda was stuck in traffic coming home from the bakery so we chatted while I made my way over US-20 to CR-17 (IN) to I-80/90 (Indiana Tollroad) to the I-69 exit where I had to pay my toll.  Traffic on her end had also loosened up by then so we ended our call.

My entire trip home was in some form of precipitation; mostly rain but occasionally sleet or snow, with very strong and gusty winds from the north that made for somewhat more difficult driving.  It also made it difficult to judge the effect of the adjusted tire pressures on handling although the shimmy seemed to be gone.  I stopped at the Michigan Welcome Center on I-69 and unpacked some of the food I had with me.  I stopped again at M-60 for coffee at McDonald’s and fuel at the TA/Shell station where Regular gasoline was $2.929.  It’s been a long time since we have seen gasoline prices below $3/gallon.  That was my last stop before arriving home at 8:45 PM.  The last few miles were through moderate snow and the strong winds had coated the north facing side of trees and road signs.

Linda helped me unload the car and get everything into the house.  I gave Butch a call to let him know I had arrived home safely and we chatted briefly about bus projects.  I took a shower and went to bed where I finished this post before 11 PM and went to sleep.

2024/11/01 (S) Words

Although we were both very tired we did not sleep well last night.  We awoke early to find a thin covering of snow on our rear deck and over parts of our yard with the temperature in the upper 20s.  We went to our SLAARC ham radio club breakfast this morning anyway, the first time in several weeks for Linda, and there was a good turnout.  Those members who came from east or south of us did not have snow on the ground.

When we got back to our house Linda worked at her desk on our personal finances while I worked at the dining room table on e-mail, websites, and bus project documentation.  Our son and daughter-in-law showed up around 3:30 PM with their daughter.  They had a baby shower to attend in Detroit and Madeline was spending the night with us.

Linda had given me the heads up that Madeline’s vocabulary had increased significantly since I last saw her and that certainly proved to be the case.  She finally had understandable words for many things including the counting words from one to ten.  She is now 22-1/2 months old and is a very active and busy little girl.  We played with lots of different toys, including a new little Thomas The Train locomotive that Grandma Linda bought for her.

We had dinner between 6 and 6:30 PM.  Madeline had mock chicken tenders with broccoli, cauliflower, mandarin orange segments and sliced strawberries.  Linda and I had yummy homemade chili that she had been cooking in the crockpot most of the day.  I played with Madeline after dinner while Linda cleaned up the dishes and then joined the fun.  Nighty-night is her current pre-bedtime game, but by 7:15 PM she was tired enough let Linda get her into her pajamas and then sit quietly while I read a couple of story books to her.  As always, she went to bed without a fuss.

Once Madeline was asleep Linda read and played online word games with friends and relatives and I continued working on my bus projects list, light bulb inventory, and reconciliation of purchases that Butch and I have made for each other.  By 10:45 PM I was tired and ready to do something else so I climbed in bed and worked on this post.

2014/11/02 (N) An Extra Hour

At 2 AM EDT this morning it was suddenly 1 AM EST so when Linda got Madeline out of her porta-crib at 8 AM, according to the clocks in our house, it was officially 7 AM.  We all slept well last night and Madeline woke up well rested and in a pleasant mood.  She enjoys her meals so before any playtime we had breakfast of toast and juice and fresh fruit.  Brendan called around 9 AM to see if we could keep her until after her afternoon nap as he and Shawna had professional work they needed to concentrate on.  I suggested they come for an early dinner and they agreed.  Linda checked her ingredients on hand and then agreed to make her seitan stroganoff served over rice.  This is one of my favorite vegan dishes and a standard ‘go to’ when we are having non-vegan company for dinner.

You cannot have too many bows in your hair, apparently.

You cannot have too many bows in your hair, apparently.

We played with Madeline all morning and she was a very busy girl.  She has understandable words for a few things and a much richer, if somewhat secret, vocabulary that she takes great delight in using.  She knows the names of her basic colors and has started to get the idea of counting.  She enjoys building tall structures with her Lego blocks and is still fascinated with the organ.  Running around the island in our kitchen is another favorite activity; sometimes chasing, sometimes being chased, and sometimes holding someone’s finger.

I got a TXT message from Chuck asking if I was back in town and had time to talk.  Linda let me take a break from playing with Madeline so I could call him back.  He has been working on their bus and wanted to bring me up to date on his projects and get caught up on my projects and timeline.

Our other grand-daughter, Katie, is up in the U. P. with Chris (her dad) and Meghan (our daughter) visiting Northern Michigan University in Marquette.  They visited the Pictured Rocks National Lakeshore yesterday and made it out to Castle Rock.  This evening they had a banquet to attend and tomorrow she has an interview for a scholarship.  Katie is interested in animals and wants to study zoology.  NMU is one of the few universities that offer a true zoology major rather than a biology major with an emphasis in zoology.  It may sound like a distinction without a difference, but it is an important distinction to Katie.  Katie is a serious young lady who has done well in school and will certainly represent herself as such during the interview.  We are excited for her and hope she is successful in obtaining this merit-based financial support.

By 11:30 AM we were anticipating lunch and Madeline requested pizza.  We happened to have an Amy’s Roasted Vegetable pizza in the freezer (our favorite) so Linda preheated the oven and baked it on our pizza stone.  We sat down at noon and enjoyed our pizza accompanied by seedless red grapes.  We were all full by 12:30 and Madeline was showing signs of being ready for her nap so Linda helped her wash her hands and face and then got her settled in her porta-crib.  Madeline enjoys sleeping almost as much as eating and went to bed without any fuss.

The cats, who had retreated to the basement this morning as soon as they heard/saw Madeline, are keenly aware of when she is eating and sleeping.  Once we have her in her high chair at the table we usually open the safety gate at the top of the basement stairs so they can come up.  Both of them did and walked around under the dining room table, apparently aware that she was not mobile.  They eventually went back downstairs but came back up once she was asleep.  We decided to leave the door to the middle/blue bedroom open about six inches to see what the cats might do.  Jasper immediately turned around and went back downstairs but Juniper stuck her head in the room, probably got sensory overload, and also left.

Linda needed a few grocery items and went to Meijer’s in Brighton where she topped up her gas tank for $2.919 a gallon.  If only the price of diesel fuel would pull back to corresponding levels.  It has dropped but not by the same amount.  I stayed home and worked on my bus projects spreadsheet.  When Linda got back with batteries I changed all of the clock batteries and reset the time.

Brendan and Shawna arrived at 3 PM just as Madeline was waking up from her nap.  She was thrilled to see her parents, of course, as they were thrilled to see her.  It was a beautiful, if somewhat chilly, day and they got her coat, hat, and mittens on and played in the yard while Linda started preparing dinner while I cleared the table of my computer and papers and set it for the meal.  We sat down to eat at 4:15 PM and started with a nice salad of chopped greens and cabbage, an Asian dressing, and crispy Asian noodles.  The main course was the seitan stroganoff served over white rice and accompanied by roasted Brussels sprouts and a sliced multi-grain baguette.  The adults had a small glass of the Leelanau Cellars Witch’s Brew, a seasonal mulled (spiced) red wine.

After dinner Brendan and Shawna began the process of getting ready to leave which includes delay tactics on Madeline’s part and their response to them which is always gentle but persistent.  They were out the door at 5:30 PM and by 6 PM we had cleared the table, rinsed the dishes, loaded the dishwasher, and picked up the few toys that were left out in the living room.  Although the clock said 6 it felt like 7.  As hard and as long as I have been working on bus projects, I am surprisingly tired after spending a whole day with Madeline.  I opened the safety gate and Jasper came upstairs right away, eager for our company and attention.  He curled up in my lap while I worked on this post.

We watched Inspector Lewis (streamed), the first TV program I have watched in quite some time.  Part of the PBS Masterpiece Mystery series, it is a really excellent production.  I did some online research on 2m/70cm ham radio antennas and dual (co-phased) CB antennas but did not come to any conclusions about what to get.  The problem remains the same; I cannot put anything tall on the roof of the bus and even if I wanted to I have little-to-no access to the underside of most of the roof.  The fact that the lower roof sections in the front and rear are part of the front and rear fiberglass caps just complicates matters even more as they do not provide a conductive path or ground plane.

 

2014/09/20 (S) Bus Talk

Leave a reply

All days have the same number of hours.  How those hours are divided up between light and dark, awake and asleep, busy or at leisure, varies with each day.  Basically, our day went like this:

  • We went to our weekly SLAARC breakfast in South Lyon.
  • We returned home so Linda could get to work on the bakery software conversion project.  She did that all day except for a break to go for a walk.
  • I called D. R. Electric Appliance to check on the range.  As I had figured it did not arrive yesterday (they would have called if it did).  They supposedly ordered it on Tuesday and told me it would take three days to get.  They do not receive product on the weekend so maybe Monday.
  • I worked at my desk on editing and uploading blog posts until 11:30 AM.
  • I went to Recycle Livingston with our weekly load.
  • I stopped at Lowe’s for a 250VAC/15A circuit breaker, outlet, and box.
  • Lowe’s parking lot connects to Walmart’s parking lot, so I stopped there for ICE brand flavored sparkling water and picked up a couple of bottles of  Leelanau Cellars Witch’s Brew seasonal spiced wine.  We had this last fall and enjoyed it.
  • When I got back to the house we had a light lunch of sourdough pretzel nibblers and hummus and then resumed our work.
  • By mid-afternoon I was tired so I took a nap.  I often do better sleeping when I’m tired rather than when I am supposed to sleep.  I also wanted to be rested enough to enjoy dinner this evening.
  • We met Chuck at the Carrabba’s at West Oaks Mall at 7 PM.  He had arrived ahead of us so we only had to wait about 20 minutes to get a table.  Linda and I both had the Tag Pic Pac, one their two vegan options.  It was long, relaxed meal and a great conversation, some of which was about buses (Chuck and Barbara also own a Prevost H3-40 converted coach).  We pulled out of the parking lot a little before 10 PM.
  • Back home we watched season 5 episode 8 (final) of Doc Martin.

That was our day and did not include construction projects or taking photographs.