Tag Archives: Village Landscape Development (VLD)

2014/08/19 (T) Horizontally Boring

Leave a reply

Yesterday the crew installing the main natural gas line down our street was at the house just east of ours, so we figured they would be at our house today.  Not long after we finished breakfast we heard the sound of trucks and checked to see where they were.  They were set up by the east end of our pull-through driveway pulling 2″ plastic pipe back through the tube they had just bored.  They then relocated their horizontal boring machine down by our third (west most) culvert that will eventually be the driveway for our bus barn.  From there they bored back towards the east following a track that was parallel to the road and about 30 feet to the north of the centerline.

We bought some marker flags at Lowe’s the other day.  I decided that this morning would be a good time to put them in the ground to mark the locations of the 240VAC/50A power lines, the propane line, the septic tank outlet to the drain field, and the drain pipe for the SE corner of the house.

The horizontal boring technology is fascinating and I got to chat with the crew chief while he worked.  He had what looked to be a fairly sophisticated measuring device that told him the current location and direction of travel of the drill head, which has electronics packaged with it that allow it to be tracked.  He relayed instructions via radio back to the operator of the Vermeer drilling rig who could then “steer” the drill head.  We also got to spend a little time by the horizontal boring machine and I tried to capture the essence of this very specialized piece of equipment.

Mel, who is one of the project supervisors, stopped to check on the crew.  I was able to get a few minutes of his time to explain our concern about how they plan to run the gas line to our house.  The diagram sent by Consumer’s Energy was not accurately drawn.  Mel called Phil, who handles the scheduling of the service drops, and had him make a note on the service card to check with us before finalizing their planned approach.  After inquiring about how many gas appliances we have, Mel said to make sure Phil gives us a 425 gas meter.

I spent the rest of the day and evening working at my computer.  I started by updating the online roster in the SLAARC/WP website.  I then selected and post-processed about 70 photos in two groups; one for the front sidewalk/stairs and one for the retaining walls and drain pipes, and created gallery posts for each project.  I will do similar gallery posts for the garage electrical/HVAC project and the natural gas project once they are completed.

 

2014/08/13 (W) Bad Times

Leave a reply

Linda had a rough night last night.  The tooth on which she just got a new crown two weeks ago started throbbing and even Tylenol did not do much to dull the pain.  She finally got some sleep early this morning and slept in while I had toast with jam and coffee for breakfast.  She called the dentist when she finally got up and they said they could see her at 10:30 AM.  She tried drinking some coffee but the hot liquid immediately aggregated her bad tooth.

Linda has been following a story in the news about Ferguson, the town in Missouri where we grew up.  There was an incident there over the weekend in which a cop ended up shooting an 18-year-old African-American male.  There were limited witnesses, so the truth about what happened is obscure at best.  The town, a northern suburb of St. Louis, is now experiencing “riots” and looting.

It is difficult for me to picture what is happening.  Although Linda’s oldest brother still lives in Ferguson we have not been back there in years.  This is the kind of situation that “happens to other people in other places” not in the Ferguson of my memory from the 1950’s and 60’s.

Darryll and Alec (DCM Heating &Cooling) showed up just after 9 AM and Linda left for the dentist at 9:15 AM.  The stormy weather of the last two days cleared out overnight replaced by cool northwest breezes, abundant sunshine, and blue skies.  When the weather in Michigan is nice it is really nice.  I took a few minutes to get the trash to the curb, made sure Darryll was all set, and then retreated to my desk to work on the membership and financial records for our FMCA Freethinkers associate chapter, of which I am the current vice-president and secretary.

I got a call from Linda around 11:15 AM letting me know she had a 2:15 PM appointment with an endodontist down the street from our dentist.  She was going to go to Fairlane Mall to kill some time but since she did not get much sleep last night I suggested she go to the endodontist’s office and sleep in their waiting room.  Given her discomfort and sensitivity to hot liquids she will likely come home today with a new root canal procedure having been done.

Darryll and Alec finished the 2″ iron pipe installation, connected an air pressure gauge, and pressurized the pipe to 12 psi to check for leaks.  The natural gas pressure in the line will only be ~4 in-WC (inches of water column).  1 PSI = ~27.67 in-WC, so 4 in-WC us is approximately 1/7 PSI, a relatively low pressure.  Still, there cannot be any leaks in the piping connections.

With the pipe done for now they turned their attention to hanging the Reznor garage heater.  To support the unit Darryll installed two U-channels in the attic spanning the top side of the bottom cord of three trusses.  He determined the location of the threaded support rods from the garage ceiling side using a cardboard template and drilled the holes up into the attic.  He and Alec then assembled everything with Darryll doing the attic work.  The Reznor is not that heavy, but he prefers to hang the unit when possible rather than screw it into something.

To position the unit they set it on top of one of our 6′ tall plastic shelving units and blocked it up another six inches with scrap wood.  (We used the same technique to install the pull-down attic ladder a couple of weeks ago as described in a previous post.)  The unit is 12″ high and they set it 6″ below the ceiling near the center of the rear (north) wall.  That location will optimize getting heat to all parts of the garage and put the unit right where Darryll needed it to connect the exhaust flue pipe using the existing flue that was originally used for the wood-burning stove.

Linda usually fixes our meals, but I used to do a lot of the cooking during “tax season” when she was working ridiculously long hours as a C.P.A.  Lucky for me we had chickpea salad in the refrigerator and I remembered how to make a sandwich.  A few almonds and some of this morning’s coffee (Teeko’s Seattle Blend half-caff) made for a tasty, quick, and easy lunch.  I checked the pressure on Darryll’s gauge and it had dropped quite a bit, so there was a leak (or leaks) somewhere that he will have to find and tighten.  That’s unfortunate given the size of this pipe and the number of connections, but “it’s all part of the job” as the saying goes.

I was hopeful that Phil from Precision Grading might come fix our pull-through driveway today, but as of 1 PM I had not seen or heard from him.  There’s still a chance we could see him later today, but it was a long shot at best based on the premise that with all the rain on Monday and Tuesday he might not be able to work anywhere else today.

Linda called around 1:45 PM to let me know the endodontist was able to see her at 12:15 PM.  They did some tests to confirm it was the nerve in the suspect tooth and then did the root canal procedure.  Apparently sensitivity to heat and a lack of sensitivity to cold is indicative of a nerve gone bad.  They gave her an initial dose of antibiotics and some pain killers (Motrin) and sent her on her way with prescriptions for more of the same.

Darryll and Alec wrapped up for the day around 2:15 PM and walked me through what they had done and what was left to do.  While I was eating, talking, and working they had run the gas pipe through the back wall of the garage and installed the flue pipe for both furnaces.  Darryll needed a few more parts to finish the job and needed to get home to deal with a flooded basement situation from the recent rains.  He indicated they should be done by the end of next week, at least with everything they can do until the gas line gets run to the house and hooked up to meter.  The timing may turn out to be tighter than expected.  When Linda turned onto our street she observed that Roese Construction had started running gas line down our road and appeared to be hooking up houses as they went, but that turned out not be the case.

I was questioning Darryll about the exhaust flue for the Reznor garage furnace and discovered that it is not a sealed combustion unit like the one we had at the other house.  He assured me it was approved for use in garages and that he has installed a lot of them over the years, but would double check to make sure.  He can return this one if needed, but said the sealed unit is more expensive.  It would also require completely different fresh air and exhaust ducting that would have to go through the back wall of the garage.  I suspect we will stick with the one that is already installed.

Darryll sprayed every iron pipe connection with soapy water and the only leak he found was the cap they put on the end of the run this morning.  Apparently they did not tighten it fully when they installed it.  He snugged it down and had Alec re-pressurized the pipe to 12 PSI but did not recheck for leaks.  (Hypothetically, if the leak at the end of the pipe was big enough other leaks might not show up anywhere else until that one was fixed.)  If there are no other leaks then the pressure should stay at 12 PSI indefinitely; certainly until they come back on Monday or Tuesday.

For dinner Linda made a nice green salad and a pepper seitan dish served over white rice; simple but delicious.  I checked the pressure in the black iron pipe after dinner, when it was cooler and the sun had dropped lower in the western sky, and it was down to 11 PSI.  That seemed like a lot of pressure loss to me, but the Ideal Gas Law (PV=nRT) says that for a fixed volume (V) the pressure (P) and temperature (T) are directly proportional (by the factor nR).  We know from experience that the pressure in an RV tire changes a little with changes in the ambient air temperature even when sitting still and quite a bit when the tire heats up from driving.  If all the tire pressures are set to the same value first thing in the morning and one side of the RV is facing south on a sunny day the pressures in the tires on the sunny side will be measurably higher than the shady side at mid-afternoon.  Of course there is a lot of air in our bus tires since they run at 100 PSI, more or less.  Most of the black iron pipe is not exposed to direct sun for most of the day so tomorrow I may re-pressurize the pipe at 10 PSI and record the pressure and temperature every 30 minutes until 2 or 3 PM to see how it varies.  Or not.

Phil (Precision Grading) called back this evening and said he could take care of fixing the driveway on Friday afternoon for a very reasonable price.  Sold.  That means we will not be going to the Clio rally on Friday for the 1 PM roundtable discussion.  So be it.  We will probably drive up on Saturday after our ham radio breakfast.  While Phil is here we are going to shoot the grade in the back with his laser level if he has time and see what we really have.  He and I agree that just eyeballing it things do not look quite right.

It’s obvious to me after the heavy rains on Monday and Tuesday that the two plastic drain pipes running out into the back yard should have had a third drain tile line put in the trench with them (perforated with an oversock) and the trench should have been filled with pea gravel to create a French drain that would remove the water flowing into that low lying area and keep it from saturating the ground.  It would also have made the pipes better able to withstand being driven over by a vehicle.  As it stands, anything heavy that drives over that area while it is moist/soft will most likely crush the pipes (again).  I’m annoyed because I did not know enough to specify this as part of the job and because Steve, for whatever reason, did not recommend it.

To fix this correctly we would need to have Phil locate the existing plastic pipe and dig it up back past the Y-connector for the two downspouts and up into the two slopes far enough that it is out of his way.  That would allow him to re-grade the entire area properly, dig a new trench starting from the edge of the lower deck, install the three drain lines, fill the trench with pea gravel, and then finish grade the slopes and valley correctly, all of which Village Landscape should have done, in my opinion, but did not.  It would also give us the opportunity to replace the corrugated plastic drain line with PVC pipe which would better withstand the weight of a vehicle once encased in pea gravel.  The rear retaining walls and front stairs/sidewalk look nice and appear to have been built correctly so we did get something for our money, most, in fact, of what we paid for, just not everything we needed.

 

2014/08/12 (T) Popcorn And A Movie

Leave a reply

It rained long and hard all day yesterday and into the evening past bedtime.  Today brought more rain, though not as hard and not quite as persistent.  Although we have low spots around our yard that turn into small temporary ponds when we get this kind of rain we are not in an area that is prone to flooding.  That’s because we live just south of the boundary between two watersheds–the Huron River to the south and the Shiawassee River to the north–so water tends to flow away from here, eventually.

Phil (Best Precision Grading) stopped by around 10:30 AM to look at the pull-through driveway he built for us last year.  He said it looked solid enough to drive the bus on it, but was obviously no longer level and had a low spot in front of the new front stairs.  He will need a half day and a small load of 21AA road gravel to repair the damage done by Village Landscape Development while building our front stairs and sidewalk.  The cost won’t be too bad (although it shouldn’t have cost us anything) but getting him to find the time to come do it could be a challenge.  He’s had a busy summer and suffered the same delays as other contractors who do outdoor work due to the wet spring and summer we’ve had.

He was also here to see the work Village Landscape Development had done.  He agreed that the hardscape work looked good but the grading in the rear did not look right and the tracks in the yard from the equipment had not been raked out properly.  He suggested I let the grass grow in and the ground dry out before assessing whether anything needs to be done.

He also looked at the west end of our property, which sits lower than the east end where the house is located.  The timing of his visit was good as all the low-lying areas had water standing in them, allowing him to see clearly the exact nature of the (lack of) drainage problem.  His suggestion was a “French drain.”  Basically it’s a trench that is shallow at the far/high end and gets deeper as it goes towards the place where the water needs to end up.  Plastic drain tile, the kind with perforations and a nylon “sock” covering, gets laid in the trench and then the trench is filled to grade with pea gravel.  The dirt that came out of the trench gets spread around to cover the pea gravel and blend in to the undisturbed soil on either side.

When completed, the drain would take all of the standing water plus much more out of the surrounding soil and allow it to flow to a culvert that runs to the southwest under the road just west of the culvert along the side of the road that will eventually be the entrance to our bus barn driveway.  A French drain is cheaper to build than hauling in large truck loads of top soil and re-grading that part of the yard.  We probably should have had Village Landscape make a French Drain around the two plastic drain lines they ran out into the yard from our basement walkout.  Oh well, “can’t should‘a done it.”

We had tofu hot dogs for lunch and then Linda left to meet up with Diane to see a movie (Boyhood) and then go out to dinner at Bahama Breeze.  I stayed home and worked at my computer, taking a break mid-afternoon to make popcorn.  The worst weather of the day was happening at that time, so I stayed upstairs for a while and read the new 2nd edition of The Mobile Internet Handbook that I had just downloaded this morning.  I worked until 7 PM and then stopped to have a light dinner consisting of chickpea spread on whole grain toast and half of a small watermelon.  Linda got home as I was finishing my watermelon.

In spite of AT&T switching our phone and DSL service to all new wire pairs our Internet service went out occasionally throughout the day and evening, although it usually returned quickly.  I think the sad truth is that their landline infrastructure is not as tolerant of wet weather as it should be and most of their money is going into expanding cellular service.  We had the same problem over the years at our house in Farmington Hills.

 

2014/08/07 (R) Endings And Beginnings

Leave a reply

I did not sleep well last night.  I was a bit worked up about the landscaping and a bit worried about the iron gas pipe installation which looked to me like it would be difficult no matter how Darryll decided to do it.  We were both awake at 5:30 AM and finally got up at 6:45 AM and had breakfast.

The landscapers arrived early, before 8 AM, and got right to work.  Steve brought three guys and got them busy right away.  Linda and I walked the site with him, but he immediately saw more problems than we did.  There was no arguing or convincing; he seemed determined to make sure it was done right and that we were happy with the end result.  He stayed and worked alongside the crew to make sure stuff got done correctly.  They finished up around 11 AM.  We took one last look at the work and paid Steve the balance of what we owed him.  He said he would check back in 2 – 3 weeks to spot seed and fertilize the new grass.

Linda took off for the post office and grocery store around 8:45 AM and I started routing and stapling the sub-panel ground conductor along the edge of the deck by the rear library doorwalls.  Darryll (DCM Heating and Cooling) showed up a little after 9 AM with his nephew, Alec, so I took the next 30 minutes to walk through the gas pipe installation options.

Darryll decided to go with the original plan of running the pipe from the southeast corner of the house down the east side, around the corner across the back of the house under the upper deck, dropping it down and going under the middle deck, across the back of the garage just below the bottom piece of siding, around the northwest corner of the garage and up the west side of the garage to its end point behind the whole house generator.  There will be a T-fitting on the garage side of the middle deck, to supply gas into the garage for the two new furnaces, and another T-fitting at the end of the run.  One branch of the end T will have a shutoff valve and cap and will be used to supply gas to the generator.  The other branch will be capped and available should we ever decide to run a gas line to the (future) bus barn.

I determined where I wanted the sub-panel ground wire to enter the basement and drilled a 5/16″ hole an inch to the right and an inch below the water faucet that comes through the west wall of the house about 16″ back from the northwest corner above the lower deck.  This allowed me to route the ground wire around an inside corner to the hole and will allow me to tuck it up under the bottom piece of siding.

I wanted to get the ground wire into the main panel but I could not turn off the main breaker as Darryll was using electric power tools and Linda was working on her computer.  The connection will have to wait until no one is using power.  Once the ground wire is tied into the main panel I will remove the bonding screw in the sub-panel.

Linda made a different kind of bean salad sandwich spread for lunch using Great Northern beans and various other yummy ingredients.  We had some grapes and green tea to go with our sandwiches.

Having run out of construction projects for the moment I decided to work at my desk for a while, but my mind was elsewhere and I just wasn’t feeling the love.  The steps at the back door of the garage were going to be in the way of the iron pipe, so I removed them.  As long as I was out there I hung around to watch Darryll and Alec get the pipe under the middle deck.  It was a challenge, as expected, but for reasons that were unseen until Darryll tried to drill holes through the end boards.

First he encountered wet wood that kept fouling his hole saw.  Then he hit a nail, which did not enhance the performance of the saw.  It also bent his extension shaft slightly which he had to stop and straighten.  He then encountered joist hangars on each end and had to bend those out of the way.  Finally able to feed the pipe through, they encountered wood sleepers and a couple of large rocks.  They managed to go over the sleepers and push the rocks out of the way and got the pipe through.  Darryll and Alec put in a long, physically demanding day and got most of the 2″ pipe installed.  Two inch iron pipe is very impressive stuff and we were very impressed with the work required to install it.

For dinner Linda made a Farro pilaf, after which we sat on our deck and enjoyed a small glass of Riesling wine to celebrate the end of the landscaping project that has had our property torn up for the last five weeks.  We are very fortunate that we became vegans and that Linda took a serious interest in learning about whole-food, plant-based recipes, ingredients, and cooking methods just as we retired.  I shudder to think what our health would be like had we continued to eat the way we did until three years ago where, even as “vegetarians,” our diet contained a lot of eggs, dairy, and seafood, and not so much fruits and vegetables.  We watched Dr. Michael Greger’s annual summary address on NutritionFacts.org and went to sleep without the worries that interfered with last night’s rest.

 

2014/08/06 (W) Arrival And Departure

Leave a reply

Well, almost.  We were up and dressed by 7 AM, had some of the granola that Linda made yesterday (soooo good), and got to work while it was still cool in the garage attic.  Our first task, however, was to straighten up the garage as we were expecting a shipment of HVAC equipment sometime today.  We cleared off the north wall and moved the plastic shelving unit there.  We gathered up various tools and supplies and organized them on the shelves.  Other things got put other places and eventually we had enough space for boxes in the back and pipe on the floor.

While we were working on the garage the landscaping crew showed up but not Steve.  They worked all day trying to finish up the job based on Steve’s verbal directions but they either got bad directions, did not understand what they were told, did not understand what needed to be done, or just did not care about the fine/finishing details absent Steve’s direct supervision.

Our next task was to pull a 50′ 12-2+g NM cable into the attic from the sub-panel location and across to the west side of the attic where I coiled it up and left it for now.  This cable will eventually provide a 240V/20A circuit for the new library air-conditioner condenser/compressor on the west end of the garage.  I will complete the installation of the outside disconnect and connection to the condenser once Darryll sets it in place and gives me the go-ahead.

I turned off the main breaker in the sub-panel and started pulling five NM cables into the panel box and making the connections.  I was part way into this work when a tractor-trailer showed up from Behler-Young with our HVAC equipment and parts.  (B-Y is the largest HVAC distributor in the State of Michigan.)  I helped Bill unload the iron pipe and the smaller and/or lighter boxes.  He unloaded the palleted equipment and heavy parts boxes using the lift gate and a hand truck.  It was a good thing we had cleaned and organized the garage when we did as the boxes of stuff took up the whole east half of the north wall.

By the time Bill left it was noon so we stopped working and had lunch.  After lunch I finished connecting the new circuits in the sub-panel, put the cover back on, and turned on the main breaker.  I tested the west and northwest outlets and discovered that the three duplex outlets closest to the back door had an open ground.  Hummm; I did not see that coming.

I tested all four of the outlets closest to the door and all of them had open grounds.  I went to the next pair of duplex outlets and found that the ones closest to the door also had an open ground but the other two tested correctly.  I turned off the circuit breaker for that circuit and took the cover plate off of the pair of duplex outlets closest to the door.  The outlets were grounded but there was only one cable feeding that box so the problem was upstream somewhere.

The box with one good and one bad duplex outlet was the likely spot.  I took the cover plate off and pulled the outlets out.  The incoming power went to one pair, the hot and neutral were bridged to the other pair, and a cable ran out from the second pair, but the grounds were not bridged through.  Really?  Yeah, really.  So I fixed it, turned the circuit breaker back on, tested various outlets, and everything was now OK.

I had assumed that that power from the attic went to the outlet box closest to the door and then ran around to the southwest corner of the garage but in fact it did not go to either of these first two outlet boxes.  Old houses often have strange wiring configurations.  We have one circuit breaker in the sub-panel that has a wire attached to it and the cable runs up into the attic but we have been unable to find what, if anything, it powers.  I also found a cable in the garage attic yesterday that runs through the attic above the library and disappears into the house attic but is not connected to anything on the garage end.  The cable is not energized and its location suggests that it may have been powered from the sub-panel at one time, but what it might have powered is a mystery at present.

Since the HVAC equipment arrived today as promised I figured Darryll would be here tomorrow to start on the installation.  We still had a lot of stuff in the garage that was potentially in his way so I moved most of it into our temporary storage pod.  It was 3:30 PM and I had apparently accomplished everything that needed to be done today.  That was an odd feeling but with nothing else to do, construction wise, I sat down and had a cup of tea.

Steve (Village Landscape Development) called to make sure it was OK to come by in the evening to inspect the day’s work and, hopefully, collect the final payment.  Linda and I did a walk-around and found so many little details that were unfinished or wrong that I called Steve back and suggested that coming this evening would be a waste of time as he would just have to come back tomorrow with a crew to fix/finish the job correctly.  He agreed.

No longer content to take someone’s word, we found our auto-level, elevation pole, and 100 foot tape measure.  (An auto-level is not a typical homeowner tool, but we have one, so I guess we are not typical homeowners.)  I set the auto-level up on the basement walkout deck and leveled it.  We pulled the tape straight out from the center of the deck 70 feet and took elevation measurements every five feet.  The grade for the first 45 feet was not clearly downhill like it was supposed to be.  At best it was level and rose slightly at two points.  There was an obvious high spot to the left headed up the slope, but I did not even bother taking a reading on that.  I really wanted the landscaping done before the HVAC work started but it looks like there will be at least a little overlap.  That means I will have to split my time and attention.  I spent a lot of my working life “multi-tasking” and now find it tiresome.  I prefer to focus on one thing at a time when possible.

 

2014/08/05 (T) Primary Elections

Leave a reply

The rain started early today with a pre-dawn thunderstorm and continued off and on the rest of the day and evening.  The area beyond the basement walkout deck is a muddy mess, but Village Landscape Development has not finished grading it.  They need it to be dry, so it may be awhile before they can finish it.

Our first construction task today was to pull electrical cable up into the garage attic for three more circuits.  I wanted to get this done early in the day while it was cool and Linda’s knee was feeling better.  I had been mulling this work over last night and realized that I had probably made an incorrect assumption about the location of the 240V/20A service for the new library air-conditioner, so I put a call in to Darryll right after breakfast.  We got a call from Karen at Bratcher Electric around 9 AM to  see if it would be OK for Mike to stop by around 11 AM to look at some electrical work we need done.  He wanted to see the job in person in order to prepare a quote.

The new cable for the outlets on the west and northwest wall was already in the garage attic but I had to crawl into the low northeast corner to reach it and get it routed in the right direction.  I then had to crawl into the same corner from a different direction to pull it to the junction box I installed last week.  I secured it with cable staples and connected it to the old cable.

Next we pulled a 14-2+g NM cable from the sub-panel to the approximate location where the garage furnace will hang from the ceiling to provide a dedicated 120/15A circuit but did not install an outlet box pending a final location from Darryll.  We then pulled another 14-2+g NM cable from the sub-panel to the north end of the new west utility closet wall.  This cable will provide a dedicated 120V/15A circuit for the new library furnace.  Again, I did not install an outlet box pending a final location from Darryll.

Darryll called back and confirmed that the new 240V/20A dedicated circuit for the new library air-conditioner had to be routed to the location of the condenser/compressor on the outside of the west wall of the garage and there had to be a weatherproof disconnect within three feet of the unit.  That meant another trip to Lowe’s, but not until much later in the day.

Mike Bratcher showed up on time and I walked him through the project.  I want to re-wire the garage sub-panel as a 100A main panel by running service entrance cable from the transfer switch in the southwest corner of the garage to the sub-panel in the northeast corner of the garage.  We may also want to run power to the bus barn if/when it gets built.  Mike suggested that they go ahead and “stub out” the barn service at the same time with an appropriate disconnect.  The plan is to have them do this work at the same time they convert the Kohler whole house generator to natural gas and do the annual maintenance.  Mike also confirmed that they can take care of the natural gas connection to the generator as long as the pipe is located near the back of the unit, has a shutoff valve, and is capped.

By the time Mike left it was after noon so we had lunch.  While we ate we ordered a dual outlet phone/ADSL filter wall plate and a few other things on our Amazon Prime account and researched candidates and proposals for the primary election.  We then went to our polling station, located about two miles from our house, and voted.

This was the first election we participated in since moving to Livingston County.  As Democrats (and liberal ones at that) in this part of Livingston County voting in the primary is an exercise.  The real contest is on the Republican ticket; whoever wins the Republican primary for any given seat will almost surely win the general election in the fall.  Still, we always exercise our right to vote and there were statewide candidates and issues.

The last cable we installed today was another 14-2+g NM to provide 120V to a junction box on the utility closet ceiling.  I mounted a round white plastic junction box approximately 8″ from the east utility closet wall in line with, and slightly in front of, the sub-panel.  I installed a plastic bare-bulb light fixture with a pull chain and 3-prong outlet to the junction box.

I did not tie any of the new circuits into the sub-panel today as we have one more circuit to pull and I want all of the cables at the panel before I cut the power and remove the cover.  We were done with electrical work for today so I turned my attention to drywall surface preparation while Linda retreated to her desk to work on tax returns.  I sanded the drywall compound as smooth as I could and wiped everything down to get rid of the dust.  I then primed all of the new and old drywall on the northeast garage wall along with the plywood platform and exposed 2×12 on the front of the base.

By the time I was done and cleaned up it was approaching 5 PM, we were both tired, and we needed to go to Lowe’s, so we decided to dine out.  We went to Lowe’s first and bought a weatherproof plastic disconnect box, a couple of watertight fittings, a 10′ length of 3/4″ plastic conduit, and a 50′ role of 12-2+g NM cable.  All of this will be used to run the new dedicated circuit for the new library air-conditioner.  We then drove to the Panera in Brighton and used one of our gift cards to have a light dinner.

We were back home a little after 7 PM.  The primer was dry so I decided to paint all of the surfaces I had primed before dinner.  While I painted Linda made a batch of her incredibly yummy granola.  We had a small glass of wine and played a few games on our iPads while the granola cooled and then turned in for the night.

 

2014/08/01 (F) Schmoo Returns

Leave a reply

(Note:  I have posted two photo galleries dated August 1, 2014, one for the front sidewalk and stairs project and one for the rear retaining walls and drain lines project.)

We took a break from personal construction projects today to get ready for another 2-night sleepover by our grand-daughter Madeline.  Her folks (our son and daughter-in-law) needed to do some painting on their rental house over the weekend and the most efficient use of their time was for Brendan to bring Madeline to our house late this morning.  That allowed him to return to Ann Arbor to work on their front porch this afternoon and will let them get an early start on Saturday morning and work as late as they want/need to.  It will also give them the option to work on Sunday morning if needed before coming to our house for dinner and to retrieve their daughter.  Brendan and Shawna both have birthdays in early August, and Brendan’s happens to be on Sunday.  Our daughter (Meghan) and her husband (Chris) will join the celebration gathering.

The landscapers were here early for what they hoped would be their last day on this job.  Linda left early to do some grocery shopping and was back well before Brendan and Madeline arrived or I had to leave for my dermatology appointment.  I got back on my computer for the first time since Monday, checked e-mails, off-loaded photographs from our digital SLR, and installed updates on four WordPress websites.

Today was also the first day to log in to edX and start the free Introduction to Linux course, but I did not have time to deal with that.  The course is self-paced and should take 40 – 60 hours to complete.  I would like to spend two hours each day on this and have it completed by September 1st.  The timing has turned out not to be that good, but I am under no obligation to take/finish the course; it’s simply a free opportunity that I would like to take advantage of while it is available.

I left for my doctor’s appointment with time to spare and ended up needing it.  There is a lot of road and utility construction going on in our area and I did not have a good way out.  I still made it on time, but not by much.  I did not have to wait very long to see Elizabeth, the dermatology PA.  I got a thorough looking over and a clean bill of health.

On the return trip from the clinic I stopped at Teeko’s to get some coffee.  Jeff had the Ethiopian Yirgacheffe in both regular and decaffeinated, so I got our usual 50/50 blend.  He was out of Sweet Dreams (a decaf blend) that I have him mix 50/50 with his Seattle Blend to make Sweet Seattle Dreams.  He did, however, have the Seattle Blend in decaf so I got a 50/50 regular/decaf mix.

Madeline was still napping when I got home.  Linda said she fell asleep a little later than normal so she let her sleep until 4:30 PM.  Once awake, she was go go go right through dinner until bedtime.

Steve (Village Landscape Development) worked on the front sidewalk in the morning, laying rectangular brick pavers in a herringbone pattern and then cutting it all the way around for border bricks.  He finished placing boulders on either side of the top steps by the front porch and had one of his crew mix up a small batch of concrete and place it along the two long/free edges.  Another crew member finished grading out the soil on either side of the sidewalk, spread grass seed, and covered it with straw.

Steve, Linda, and I did a walk-around, and the project has come together very nicely except for the leaking drain line(s).  Steve spent much of afternoon digging in very muddy conditions and ultimately unearthed about 30 feet of plastic drain line that was punctured or completely crushed.  He replaced what he believed was all of the damaged line, but until we put water down them we won’t really know.  They were not able to finish the grading because the clay soil was so wet that it was unworkable, so they will be back next Tuesday (or later) weather permitting.  They had to come back anyway as they needed a bit more egg rock to finish a bed that we added at the last minute.  As a result of the walk-around we added another bed of egg rock at the east end of the deck to tie in with rock under the deck, and two more downspout drain lines, all of which they will do the next time they are here.

 

 

2014/07 – Retaining Walls & Drains

Leave a reply
Panorama of retaining wall project drain lines (looking N from deck).

Panorama of retaining wall project drain lines (looking N from deck).

Village Landscape Development of Fenton, Michigan was at our house (off and on) for the entire month of July working on two projects.  The larger project was tearing out two stacked block retaining walls by the basement walkout and replacing them with boulder retaining walls.  This involved significant regrading of the area and the installation of drain lines for the downspouts from the roof and the sump pump.  This gallery post contains a selection of photos that show the highlights of the work from beginning to end.

2014/07 – Front Sidewalk and Stairs

Leave a reply

Village Landscape Development of Fenton, Michigan was at our house (off and on) for the whole month of July, 2014 working on two projects.  This gallery post has a selection of captioned photographs from the front entrance sidewalk/stairs project.

2014/07/31 (W) Wrapping Up?

Leave a reply

We were tired and went to bed early last night.  Naturally, that meant we were up earlier than usual this morning.  Linda made her fabulous vegan blueberry pancakes to get us fueled up for a long day of work.  The landscapers were also here reasonably early and had a very productive day.  More on that later.

Our first task this morning was installing a switch controlled dual LED floodlight fixture on the back of the garage above and to the left of the door (when viewed from the outside).  The location was determined by the construction of the rear wall of the garage.  I measured and re-measured the location of the cable hole to make sure the surface mounted junction box ended up in the center (vertically) of one of the siding boards.  I drilled a 1/2″ hole through the back (north) wall of the garage just to the right of the back door (when viewed from inside the garage) and just below the top plate.  I ran a 14-2+g (NM) cable (that I had previously prepped and left in the wall cavity) through the hole in the wall and then through the hole in the back of the junction box.  This was the part of the north wall where I had to remove concrete backer board, a burned 2×4, and singed insulation, so the studs and back side of the exterior plywood sheathing were exposed and accessible.

We moved around to the outside and I caulked the hole around the wire, put a generous band of while caulk around the hole on the back of the junction box, and a half circle of caulk around the top back edge of the box and mounted it to the outside of the house with the center knockout centered over the hole in the wall.  I installed the dual LED light fixture and put a bead of caulk around the top half of the junction box where it met the fixture.  (The heads of the cheap machine screws that now come with electrical fixtures and plates strip very easily making it difficult to get a tight fit.)  I caulked the wire hole from the inside and then dressed and secured the cable.  I turned the circuit breaker on, and checked for proper operation of the switch and light fixture.  It was all good.  I like it when that happens.

Our next task was to install three round blue plastic junction boxes for bare bulb light fixtures; two for the garage attic and one for the garage end of the library attic.  I was originally going to install a switch near the top of the fold-down ladder to control the lights and run power to it from a new ceiling light fixture in the utility closet, but we came up with a better solution.

There was a three-gang electrical box in the east wall of the garage just inside the door from the library.  It had two switches installed and the cover plate had openings for a duplex outlet in the third position, but no device installed there.  We thought this would be a better place for the switch—as there was already power to the box—if we could get a wire through the wall from the attic to the box.  The drywall is missing from the lower half of the wall so we had good access to the underside of the box.  (The drywall was removed by the previous owner to repair the frozen hot water baseboard heat pipes.)  I checked in the attic and it looked like we had a good shot at making this work.  The icing on the cake was that we could install a switch with a pilot light that is designed to fit in a duplex outlet cover plate.  Not only would it be convenient, it would provide a visible indication that the lights were on.

I did the attic work while Linda took care of the garage end of this task, passing me parts and tools as needed and helping feed NM cable. We ran 14-2+g (120V, 15A) wire from the attic through the east wall to the existing outlet box.  I pulled the cable over to the location by the library attic, mounted the box, cut the cable, unsheathed it, stripped the wires, ran it into the box, and secured it to the truss.  I repeated that process with the end of the free cable.  The plastic light fixtures I bought very conveniently feature pass-through wiring terminals so all I had to do was hook up the cables, fasten the fixture to the box, and screw in the 100 W rugged service bulb.

I repeated this process for the next box/fixture which I positioned just to the west side of garage ridge 1/4 of the way in from the front (south) wall.  Finally, I repeated most of this process for the third and final (for now) box/fixture which I positioned on the east side of the ridge 1/4 of the way in from the back (north) wall.  Somewhere in the middle of all that we stopped for lunch.

With the attic lights installed I needed to pull the wire that supplied power to the outlets in the west half of the garage out of the rear/north wall and up into the attic.  Easier said than done.  The cable was originally part of the circuit that powers the outlets in the northeast wall of the garage (and now powers the new floodlights on the back wall) but I disconnected it a week ago knowing that I wanted to feed it from a separate breaker.  The cable went through a hole in the top plate and I discovered that the bottom cord of the gable truss had been set partially covering this hole with the cable pinched under it.  I cut the cable from above and ran it into a plastic switch box.  Linda was then able to pull the tail end loose from underneath.  I will run a new cable from the sub-panel to the junction box after I get more pressing work done.

On that note I also realized today that I do not have to get the cables for the new circuits through the top plates above the sub-panel, which was going to be difficult-to-impossible.  The sub-panel is surface mounted and I already planned to box around it.  With the supply air duct coming out of the new HVAC unit and running straight out along the ceiling above the utility closet door I will have 16 inches of clear ceiling space.  The sub-panel is about four inches deep so I will have about three inches of ceiling above the panel and in front of the top plates where I can run new cable into the attic.  Brilliant!

Our last attic task for today was to disconnect two telephone wires in the wall cavity to the right of the sub-panel, pull them up into the attic, reroute them, and reconnect them.  One of them turned out to be the main phone/data line coming into the house from the AT&T box at the southwest corner of the garage.  There was a telephone wall outlet to the right of the old sub-panel that this line ran to before continuing on to the rest of the house.  The wires are very small gage, are unshielded, and the cable is draped through the attic over multiple 120 VAC cables.  I need to replace this with a single run of much better (shielded) cable when I have time.  Perhaps we will get less static on the phone and faster Internet data transfer rates.  (Nah, probably not.  It will still be an AT&T landline.)

While I started working on re-wiring the three-gang box in the east garage wall, Linda made a run to Lowe’s to get a 32′ roll of 16″ x 3.5″ (R-13) insulation and a switch with a pilot light.  I got the box rewired, we energized the circuit, and everything worked.  Yippee!

The landscapers today consisted of Steve (the owner), Spencer (his nephew), and Tommy.  Steve used the excavator to place four large boulders on the sides of the new front steps.  That was the last work to be done in front that required the excavator so he used it to back blade (level off) and compact (with the bucket) the pull-through driveway.  He was not able to return it to its existing condition but did the best he could with the equipment he has.

He took time out to use his chain saw to cut down a dead pine tree, cut it up into 4′ lengths, and carry the pieces back to his truck with the excavator.  He then used it to fill/grade a large low spot just southwest of the garage.  This was the route they used to get the excavator to the back yard.  It was also where all of the construction debris was piled until yesterday, and the excavator really tore the ground up in that area over the last four weeks.

Spencer and Tommy worked in the back hand-grading the slopes beyond the retaining walls and the area that was trenched for the drain tiles.  They worked in a layer of good topsoil, spread grass seed, and covered it with straw.

Steve plans to lay the brick pavers for the front sidewalk tomorrow and have the whole project wrapped up by the end of the day.  It looked like they were on track to accomplish that until Spencer informed us that there was apparently a leak in the drain tile somewhere in “the valley.”  Leak was an understatement; we had an area at least 8′ x 12′ that had turned into a pond.

It appeared that the drain line for the sump pump was somehow discharging its water at this point rather than it flowing all the way down to the drains at the back of the yard.   Spencer dug up some of the line coming down the slope and found several holes on the top side, but it did make sense that these were the source of the problem.  Our guess is that that line, which is not one continuous piece of drain tile, has become disconnected at the valley floor allowing all of the water to escape at that point, and/or crushed, causing the water to back up through a connector (which is only designed for water to flow one way).  Fortunately we kept the original PVC discharge extension pipe from the sump pump outlet so we temporarily disconnected the buried drain line and reconnected the extension pipe.

Whatever the cause of the leak, we are sure it will be found and fixed, we’re just not sure that will happen by the end of the day tomorrow.  I had thought about “testing” the system by using a garden hose to put a significant volume of water into each of the drain lines.  As of now, I will definitely be doing that.

Our final task was insulating a section of the rear/north wall.  We got three of the four plus cavities filled and ran out of steam.  Besides, it was dinner time.  Linda made one of her “go-to” dishes; angel hair pasta with onions, garlic, mushrooms, sun-dried tomatoes, basil, and mixed baby greens lightly sautéed in olive oil.  This is a dish she can throw together from ingredients on hand without a recipe and it is always delicious.  We had a small glass of Leelanau Cellars Summer Sunset wine while she cooked and a small glass of Meiomi Pinot Noir with the dish.  No salad and no dessert; just a great pasta dish and nice wine.  I got cleaned up and we watched the first episode of season five of Doc Martin.  As we were drifting off to sleep we thought we heard the distant howl of a coyote.

2014/07/30 (W) Winter In July

Leave a reply

By the time we started breakfast the landscapers were back.  Steve started to dig a trench for a drain line from the end of the lower deck and hit 2×8’s on the flat about 2-3″ below the surface, so he abandoned that work and moved the excavator around front to the trash pile.

The major construction work up in the back is nearing completion and the lads were picking up some of the smaller debris, the larger stuff having been moved around front to the trash pile yesterday.  Steve used the excavator to load some of the trash onto the trailer (normally used to move the excavator), where the crew covered and secured it.  He loaded more of it into the back of his pickup truck.  They are still having tire issues with the trailer so I charged up my 200 psi air compressor (150 psi regulated) and rolled it over so they could fill one of the tires.

Steve moved the excavator to the southeast corner of the house to dig a short (10′) shallow trench for a drain line to get water from the downspout away from the house.  I conferred with him regarding the exact location because the main propane line enters the house at that corner, the electrical service for the RV outlet runs under there, there is a tree about 12 feet southeast of that corner, and that corner is where the new natural gas meter will be installed. There will be a similar short drain line at the southwest corner of the garage, but it will be dug by hand as the main electrical service runs directly under there about 2′ below the surface.

The lads continued to work in the back placing egg rock.  They were about 1/2 cubic yard short and I asked Steve to order a full cubic yard and use the other 1/2 yard on the west end of the north edge of the lower upper deck to match what they had done at the top of the west retaining wall.  Steve gave the crew instructions on how to prep that area, add a piece of edging to define where the rock will go, and install landscape fabric.  He and I then looked at the boards he hit in the back while trenching and it turned out there were only three of them 4-6′ long and they appeared to be old construction material that had possibly been used as a step off of the lower deck.

Linda gathered up household trash and recyclables and headed off around 10:45 AM.  I finally got started on my projects for the day around 11 AM, opening the garage door so I would have light when the power was turned off at the sub-panel main breaker.  My first task was to move the new outlet I installed in the utility closet the other day.  The return air duct will be installed against that wall and would cover the current location.  When we installed the door yesterday we did not put any 2×4’s above the door and up to the ceiling.  Darryll is going to run the supply duct straight out from the furnace above the door and then angle it over against the east wall of the garage.

With the outlet relocated I cut some scrap insulation to fill the lower half of the open wall cavities and then stopped while I pondered getting a ground wire into that space.  Linda got back from running her errands about then so I decided over lunch to call Bratcher Electric to see if they could give me an idea of what it will cost to run a 100 Amp service entrance cable from the transfer switch in the southwest corner of the garage to the garage panel in the northeast corner of the garage.  (I estimated it would take 40′ of cable, but have no idea what the labor will be.)

The earliest I will be able to talk to Mike Bratcher is next Monday so I decided that I really needed to run a ground wire from the sub-panel to the main panel allowing me to disconnect the ground wires from the neutral wires in the sub-panel by removing the bonding screw in the sub-panel and giving us a code-compliant, and much safer, sub-panel until such time as it gets re-wired as a main panel.

Linda and I determined that I needed about 40′ of #10 copper wire to get from the sub-panel to the main panel.  Pondering sometimes leads to good things.  I really did not want to stop working to go get wire when I remembered that I had a length of green insulated copper wire I had used for grounding a ham radio and antenna mast at the old house.  It was coiled up on the floor in garage and when we uncoiled it we discovered it was … 40′ long!  I love it when that happens.  I checked the gage and it was #8, so it was actually larger than required for the 60A cable that feeds power from the main panel in the basement to the sub-panel in the garage.

I checked the approximate location for drilling a hole and then drilled a 1/2″ hole from the inside of the garage just above the base plate and out through the siding.  I fed the ground wire through the hole from outside the garage, pulled it up into the sub-panel, and secured it to one of the ground bars.  I dressed it and fastened it to the side of a stud and coiled up the extra outside on the lower upper deck.  I will complete the run to the main panel another day.

With the ground wire installed I was able to install the insulation I had cut earlier and secure it with our staple gun, which I had managed to locate in the tub of tools we took with us out west last summer.  With Linda’s assistance I cut and installed two pieces of drywall from an old scrap piece we had.  I then taped the seams and mudded the screw dimples.  By the time I finished it was 4 PM.  Spencer came to the garage to let me know that they would all be leaving around 4:30 PM due to a severe thunderstorm that was on course to hit our area around 5 PM.

By 4:45 PM we were hearing thunder and I decided to stop work temporarily and help Linda close up the house.  The storm came, a cold wind blew, and it rained hard, but only for a few minutes and we did not get any of the hail that was reported prior to the storm’s arrival at our location.  An hour later we had a lovely summer evening with blue skies.  Linda made roasted winter vegetables for dinner.  It’s the end of July, but we had overnight lows in the mid-40’s two nights ago.  The first six months of this year have been the coldest in 21 years, so winter vegetables were appropriate for dinner even though it is the end of July.

I had planned to do a lot of other electrical work today, but it was a full day and everything that got done was something that needed to get done.  It was also work that had to get done in the order in which it was accomplished.  My original plans were obviously too ambitious, and today’s work involved details that required time to figure out and execute.

 

2014/0729 (T) Utility Closet

Leave a reply

It was in the mid-40’s when we got up this morning so Linda made oatmeal with walnuts, dates, raisins, cinnamon, and a little brown sugar.  It was a hardy and satisfying breakfast on a chilly morning.  I checked in with some of the blogs I follow using Feedly on my iPad and then, as we were getting ready to work, Steve showed up with four workers (Kyle, Tommy, Spencer, and Mark).  Steve did not stay and work today but Mark operated the excavator and the guys got a lot done.  By the end of the day we were finally able to see how it was all going to come together.

Our focus today was the utility closet in the garage.  Much of what we did required two people, and we made a long day of it.  We finished framing the west wall, stood it up, got it into position, plumbed it, and secured it.  We then framed the south wall with the rough opening for the door.

The installation of the door was challenging.  All the framing was plumb in two directions but our first attempt at installing it resulted in the bottom latch side not closing by almost an inch when the top latch side was seated correctly.  Everything was plumb on both jambs, the door was level and plumb, but something was obviously wrong.

As we started to break for lunch I got a call from Darryll.  He was wondering if we could run the 2” iron gas pipe through the attic from the east end of house to the west side of the garage.  I told him I would check the access and call him back.  While he was on the phone I got clarification on the size and location of the HVAC unit and the ducts for the conditioned air supply and return.  As a result I will have to move a duplex outlet I installed the other day, run a new/longer wire up the sub-panel, put insulation into the lower half of the wall cavities, and install/finish a piece of drywall.

We spent the afternoon trying to figure out what was wrong with the door installation and fix it.  Everything was plumb and we thought everything was square.  It turned out that the two ends of the wall were out of alignment which was forcing the bottom of the door out.  (The inside angle between the west wall and the south wall was less than 90 degrees.)  Once we realized what was wrong we were able to fix it.

We had a green salad and Amy’s roasted vegetable pizza for supper at 6:30 PM.  After relaxing for a while on the deck with a glass of Leelanau Cellars Summer Sunset wine I secured the plywood platform to the base with screws and then caulked the two edges where it met the back and right side walls.

We drove to Lowe’s at 8 PM to get a box of steel cut masonry nails.  I need two or three to secure the free end of the bottom plate of the west wall.  While we were there I got a set of new blades for the Milwaukee Sawzall reciprocating saw but forgot to buy more shims.  We always like to leave a reason for a return trip to the home supply stores.

 

2014/07/28 (M) Reprieve

Leave a reply

I was awake early, fell back asleep, and finally got up at 7:30 AM.  By the time I had the coffee made Linda was showered, dressed, and starting to assemble breakfast.  We had barely finished eating when we heard the happy sound of landscape workers.  Steve had five young men on site to do the hand work and was here most of the morning and part of the afternoon running the excavator.  By the time they all left for the day a little before 5 PM they had made a lot of progress with the retaining wall project behind the house in spite of the muddy conditions from yesterday’s rains.  It’s amazing what can be accomplished when people and equipment show up and work all day.  If that happens the rest of the week they might actually get done by Friday.  Linda and I figure it will be Labor Day.

As planned, I resumed work on the utility closet in the garage after breakfast and a brief chat with Steve.  I cut a 48″x48″ piece of 3/4″ plywood down to 46″x40″ and did some minor trimming to get a clean fit on the base we built yesterday.  I then cut the top and bottom plates and the end studs for the west wall from 8′ long 2″x4″s.  I ran out of the 3.5″, 16d nails I needed so I drove to Lowe’s to get a 5 pound box of them.  While I was there I also picked up some primer and paintable caulk.  I assembled the outer pieces of the wall and added an additional stud to the free (south) end but did not cut/install the other three intermediate studs.

The wall is taller at the north end than the south end because the concrete garage floor drops slightly towards the north wall of the garage.  I stood the wall up to make sure it fit snugly (it did) and to force the top plate into alignment.  I was pleased to see that the free end will plumb quite well in both directions.  I will measure the other three studs tomorrow, lower the wall down to install them, and then stand the wall back up, plumb it, and secure it to the north wall, the platform base, and the ceiling.  Once that is done I will secure the plywood platform to the base using screws and caulk the edges along the north and east walls.  When the caulk has cured, hopefully later in the day, I will prime the plywood and the exposed 2″x12″ base board.

I quit working on the construction around noon, got cleaned up, put a load of laundry in the washing machine, had a bite of lunch, and withdrew to my office.  I searched through my Outlook inboxes for all of the e-mails related to today’s FMCA Education Committee meeting only to discover that the meeting was scheduled for next Monday and would be an informal work session rather than a formal meeting.  That was a lucky reprieve for me and allowed me to catch up on other e-mail and work on the roster and financial records for our FMCA Freethinkers chapter.

I had hoped to spend the evening selecting and processing a few photos and uploading a few blog posts but I ran out of time and did not get to these tasks.  We streamed last week’s episode of Endeavor on our Apple TV device and then turned in for the night.

 

2014/07/25 (F) Assessing The Situation

Leave a reply

We finally got a letter yesterday from Consumer’s Energy requesting payment of the $200 fee for hanging the natural gas meter.  The letter included a rough drawing showing where the meter will be located (south end of the east side of the house where the propane currently enters).  It also shows the route the gas line will take to get there from the opposite side of the street.  The drawing did not correctly show our pull-through driveway in relation to the house, so the actual path will be different.  This was also the first indication we’ve had that the main line will be run down the opposite side of the street, which we prefer over running down our side of the street.

At 9:15 AM we still did not have any landscape workers on site so I went to my office to continue working on assessment items.  No one from Village Landscape Development showed up today and we never got a phone call.  It’s a way of doing business that I simply do not understand.

I finally got around to making my annual appointment with my dermatologist only to find out he is still on medical leave.  I didn’t know he was on medical leave in the first place.  They scheduled me with someone else in the same clinic.

After lunch I had a nice chat with our financial advisor / stock broker at Stifel-Nicholas even though we just saw him three weeks ago.  We got a post card a few days ago indicating that he and his assistant were moving to a different S-N office.  He had not mentioned this when we met in person so we wanted to see what the reason was for the move, which he gladly explained.  No cause for concern on our part, which left me free to worry about other things instead.

As long as I was making phone calls I called Butch to see how things were coming along following the sale of a large portion of their business assets to a company in Nevada.  They still have a lot of loose ends to tie up and a bus conversion to finish, so they are not sitting on their hands.  When the buyers were there a week ago they loaded up as many parts and as much material as they could transport in the vehicles they had, but by Butch’s estimate it wasn’t 20% of the total.

I also had a series of TXT messages with Joe Cannarozzi, the mobile mechanic who has taken care of our bus the last four years.  Joe is relocating from Chicago, Illinois to Myrtle Beach, South Carolina and giving up the mobile aspect of his bus repair business.  Apparently his new place has a garage where he will continue to work on rigs, but they will have to come to him.  I hope that works out for him, but it leaves us having to find a mechanic closer to home or willing to travel here.

I finished writing the assessment items for the three remaining Michigan Assessment Consortium Common Assessment Development modules and got all seven sets of items e-mailed to the team.  With that task checked off, at least until I get some feedback, I was free to go to Lowe’s after dinner and pick up some of the materials I need for the HVAC projects in the garage.  There’s a better than even chance that we will not go to our ham radio club breakfast tomorrow in favor of an early start on the garage work.

 

2014/07/24 (R) Back To Work

Leave a reply

We were up earlier than normal.  Linda went into the bakery today and likes to be on the road ahead of the worst of the morning traffic rush.  Since she was working I figured it was a good day for me to also do some paid work (plus a couple of loads of laundry).  Earlier in the summer I agreed to write assessment items for some of the modules in the Michigan Assessment Consortium professional development series on Common Assessment Development.  The items are needed for use with the Lectora platform, which Bill Heldmyer at Wayne RESA is using to re-package the modules.  These are modules that other team members developed, so I have to spend some time with the content before I can write the items.

I did some work on this in June and then got busy with contractors and out-of-town trips.  I am still tied up with construction, contractors, and other projects but a timely completion for this work would be early August so I spent much of today working on it.  I already had one module done and hoped to finish the other six but only managed to complete three of them.  I am anxious to get back to work on the HVAC prep in the garage but I plan to continue working on the assessment items tomorrow as I would like to e-mail them to the team for feedback before the end of the day.

I have a lot going on at the moment.  I like being busy, but this is starting to feel like “work.”  I have a growing list of “must do” bus projects that I have yet to start:  1) fogged window replacement; 2) auxiliary air filter / water separator replacement; 3) Aqua-Hot expansion reservoir replacement; 4) Aqua-Hot exhaust leak repair; 5) motorized windshield shade repair; 6) finishing the installation of the ZENA power generator (for charging the house battery bank while driving), and; 7) redoing the water bay (that’s a big one).  I have an optional project to replace the rear view camera system.

Butch is building new ride height linkages for his bus and wants to build some for me as well, so that makes nine “bus projects” I would like to accomplish before the weather turns too cold to work outside.  Some of these are projects I can do with the bus in front of the house once I can move it back into its normal parking spot.  The rest are things I will work on once I get it down to Butch and Fonda’s place in Twelve Mile, Indiana, probably this September.

The FMCA education committee work is ramping up and I have three websites I am trying to launch, one of which has an August 11 target date, plus our own website/blog to maintain (as of this writing I am over two weeks behind on blog posts).  I am also supposed to be writing a “featured bus” article for Bus Conversion Magazine on Marty and Pat Caverly’s MCI MC-5B conversion “Scooby Doo & Bookworm.”  It’s a great conversion that has taken 20 + years to build and will be the cover/centerfold story when it is published.  I have 1,500 photos from Marty and the only way I will make sense of the project is to sit down with Marty, select images, and make notes.  Once I have a sense of the chronology of the work, and the images to illustrate it, I can weave the words together to tell the story.

Kyle and Spencer were here working on the landscaping for most of the day.  Steve stopped by in the morning to go over the work from yesterday and outline the work for today.  It’s coming along, albeit much more slowly than I think it should.  For a job that requires a lot of manual labor we normally only have two guys on site, sometimes three and sometimes only one.  And, sad to say, they simply do not work as hard and as persistently when Steve is not here.

Linda got home ahead of the afternoon traffic.  We had leftover potato and lentil curry and naan for dinner and both the dish and the bread were still excellent.  A few black grapes and dark, sweet cherries for desert and we were off to bed early.

 

2014/07/23 (R) My Platform

Leave a reply

The primary elections are just around the corner but my platform has nothing to do with politics.  My platform is a 46″ x 40″ surface 12″ above the floor in the northeast corner of the garage, or will be once I build it.  This platform will be the base for the new HVAC unit for the library and I need to have it built before the equipment gets here and Darryll shows up to install it.  Once the unit is installed I need to enclose it to isolate it from the garage to prevent explosive vapors or noxious fumes from entering the combustion chamber or fresh air circulation.  That will require the construction of two walls one of which will have an exterior grade door.

John’s chop saw, which I borrowed the other night, allows me to make more accurate cuts (clean and square) than I can with my circular saw.  In the meantime I have some work to do removing/installing a few studs in the north wall of the garage and running some new electrical wire.  I need to run 120V 15A circuits for the furnace portion of the library unit and for the ceiling mounted garage furnace and a 240V 20A circuit for the library air-conditioner.  Eventually I will have a 240V 30A outlet for our radial arm saw, which would be great for the woodworking aspects of this project, but that’s a project for another day.

Three landscapers showed up a little before 8 AM (Tommy, Matt, and Spencer).  Tommy was on the phone with Steve getting their instructions for the day and then they got to work building an additional section of the west retaining wall with medium size boulders and preparing the area under the east end of the deck for a layer of egg rock.  They took off around 9:45 AM for some unknown reason, but the sound of their truck reminded us to put the trash out at the street for pickup.  They were back in a little while, worked until noon, and took their lunch break.  By 3:30 PM they had the boulder wall built, the egg rock placed, a strip of edging set into a small trench, and small boulders placed on the eastern slope below the large boulders.  That certainly looked like progress.

Linda worked at her desk until mid-afternoon and then started working on dinner.  Although simple in presentation at the table, she put a lot of time into our meal.  She made a potato and lentil curry that was very good with deep, complex flavors, and garlic naan bread.  Both were as good as anything I have ever had at an Indian restaurant and the naan was vegan, made with unsweetened soy milk in place of dairy milk and olive oil in place of dairy butter.

I spent most of the day taking the measurements I needed to turn my mental concept for the utility closet into a set of design drawings from which I could produce a material list.  By supper time I had a good set of drawings to guide the carpentry work but was still puzzling over some electrical issues.  By the time Linda had dinner ready I was ready to set thus project aside for the night.

It was after 7 PM by the time we finished eating and cleaned up, but that left us plenty of time to sit on the deck and enjoy a cool northwest breeze and the muted light of scattered clouds.  It eventually got too cool to stay outside so I worked at my computer until bedtime.

 

2024/07/22 (T) A Quiet Day At Home

Leave a reply

We ran the air-conditioner all day yesterday and well into the evening.  It cooled off into the mid-upper 60’s overnight so we turned the A-C off when we got up this morning and opened up the house.

Ron and Mary were mostly packed before breakfast.  We all had some of Linda’s yummy homemade granola with fresh blueberries for breakfast and everyone agreed it was superior to any store-bought granola they had ever had.  We visited until 9 AM and then helped them load their car for the trip back to Pennsylvania after an all-to-short visit.  Still, it was nice to see them for the time they were here and they got to see our grand-daughter for the first time and chat briefly with our children.  They had a nine hour drive ahead of them, plus or minus, depending on traffic, construction zones, and number/length of stops.  The day was forecast to be sunny and very warm, with a high temperature at our house of 90 degrees F, but with no precipitation along their route.

Only one landscaper (Spencer) showed up this morning around 10 AM.  Steve had some hand work for him to do.  I checked to see that he had water and he assured me that he brought plenty to drink.  With the outside air temperature rising, we closed the house up and turned the A-C on.

We were both surprisingly tired but wanted to get something useful accomplished today.  Linda worked at her desk while I cleaned the concrete driveway leading up to the garage from the street.  The landscapers have been using the driveway to stage some of their bulk materials such as crushed limestone and egg rock.  They got all of that material moved to other parts of the yard over the weekend but there was a layer of dust, small rocks, and other debris left behind.  I swept most of it off the driveway with a large push broom and then finished the job with a leaf blower.

There was a lot of crushed limestone left so over the weekend I had Steve push it into a 8′ wide by 15′ long parking pad 4″ – 6″ deep off the west side of the driveway and adjacent to the woods that run along the road.  The pad still had tracks in it from the excavator treads so I raked those out, filled in some dirt around the edges of the pad, and tamped the edges down.  The pull-through driveway from the front stairs to the concrete driveway was also rutted from the Bobcat front-loader being driven on it so I raked that out as best I could.  By the time I was done it was noon, it was hot, and I was sweaty and thirsty.  I decided I’d had enough for the day, closed up the storage container and garage, came in, and drank a bottle of ICE brand water.  This water is lightly carbonated and lightly fruit flavored, and I find it very refreshing.

I had a phone message yesterday from Darryll of DCM Heating and Cooling with some information I needed in order to prepare the corner of the garage for the library HVAC unit.  There were a few things I still needed to know, so I put in another call to him and left a message.  For lunch Linda served the left over salads from last night’s dinner along with hummus and chips.  We sat on the back deck for a while enjoying the slight cooling effect of a warm summer breeze, but eventually went back inside to escape the heat.

We did not do much the rest of the day.  I apparently broke our grandfather clock on Monday while winding it and spent a little time looking for information online.  I found a Sligh manual that included some troubleshooting tips but did not get as far as trying to diagnose and fix the problem.  We were both tired and took naps in the late afternoon.  That was unusual for us but could easily become part of our daily routine, especially on hot days like we had today.

I worked on bus barn drawings while Linda prepared dinner.  I then called John to see if I could borrow his chop saw and if he had time to look at the drawings.  Linda went along and visited with Diane.  We stayed until almost 10 PM.

 

2014/07/20 (N) Company

Leave a reply

The landscapers were back at 7:45 AM as promised.  We were up and ready for them and I was back working on the new sub-panel in the garage by 8:30 AM.  I finished the work (for now) and cleaned up the mess as best I could.  Electrical work, especially panel wiring, is very physical and tends to produce a lot of scrap.  Once the garage was cleaned up I applied the same treatment to myself.  By 1 PM I was ready for part 2 of my day, which began with a load of laundry, and then off to my desk to put a little time into our much neglected blog.

I have been taking photographs and writing daily blog posts all month but have not been taking the additional time to select and process the images and upload the posts to our WordPress site.  The last blog post on our website is from July 6th.  During the early afternoon planned to upload a few of the posts while we waited for Ron and Mary to arrive.  I ended up filing and deleting e-mails, which I have also neglected for the last few days.

Ron (Linda’s brother) and Mary (Ron’s wife) arrived at 3:30 PM.  They are on their way back to Pennsylvania after a week in Madison, Wisconsin participating in day-long bicycle rides.  They are fairly serious bicyclists; a few years ago Ron rode from Seattle to Boston with a large group over the summer.  This was their first visit to our new house so they got the full tour of the house and the property.  We were sitting on the deck enjoying cool beverages and good conversation when the landscapers returned.  They were still working with their heavy equipment, so we went back inside to talk.

Linda started pulling dinner together at 5:30 PM with Mary’s assistance.  We had a green salad with cut up vegetables and seitan stroganoff served over white rice the way I like it.  A glass of Merlot balanced nicely with the richness of the stroganoff.  Linda, Ron, and Mary went for a walk after dinner while I loaded and started the dishwasher.  When they returned we talked into the evening and Mary showed us pictures from family gatherings and their just-completed bicycle rides.  Linda had baked a vegan chocolate cake this morning and served slices with fresh cut strawberries and vanilla coconut milk ice “cream” for dessert.

 

2014/07/14 (M) Education

Leave a reply

Linda was up at 6 AM and was out the door and on her way to Twelve Mile, Indiana at 6:30 AM.  She decided last night not to have breakfast at home in favor of getting on the road.  I slept in and got up at 7:30 AM.  Lind’s homemade granola made for an easy, tasty breakfast.

Two landscapers showed up a little before 9:00 AM as I was getting ready to leave to run some errands and said Steve was on his way, so I stuck around until he got there.  We looked at a few things together and then I left.

On the way home from running my errands I got a call from TOMTEK reminding me that we have an annual service contract with them for the main house furnace (hot-water base-board heat) and air-conditioner.  I agreed to have them come on Thursday to service the A-C.  Perhaps while they are here they can figure out why it makes a noise that sounds like the thump, thump, thump of a helicopter blade.

About a mile from the house I spotted a small Painted Turtle trying to cross Hacker Rd.  A truck going the other way spotted it at the same time.  We both turned around and came back.  I got there first and put it on the front passenger floor mat after assuring the other driver that I was going to take it to our property and release it near the (neighbor’s) pond.  Turtles have very little chance of successfully crossing a road most places, including around here.

The two landscapers worked into the afternoon.  They could only go so far before needing Steve to inspect and approve their work.  He did not make it back today and I think they quit working around 3 PM.

Education is what I did professionally for the last 21 years before I retired, and I am still doing it to some small extent.  Back in the late winter I agreed to serve on a newly reconstituted FMCA national education committee.  There are 6 – 10 people on the committee, depending on how you count, and except for a couple of staff at FMCA headquarters in Cincinnati, Ohio we are spread out all over the U. S.  Our meetings are, therefore, conducted by telephone conference with ideas and information shared via e-mail in-between.  I also set up a folder in our personal Dropbox as a place to put documents so the committee can retrieve them.

We had our third meeting today from 4:00 to 5:30 PM EDT.  I spent the rest of the evening creating an outline of a possible RV curriculum and dealing with e-mail related to our meeting.  Linda got home at 8:00 PM and we had leftovers for dinner, after which I returned to my work and she headed to bed.

I have one, maybe two, days to concentrate on desk tasks.  Once the Pack-Rat storage container arrives on Wednesday I will be tied up with house-related chores through the 19th and then company through the 23rd.  I expect delivery of some HVAC equipment and materials during that window.  With any luck Darryll will be here starting on the 24th and I will be tied up working with him through the end of the month.  I’m hopeful, if not optimistic, that the landscapers will also be done with their two projects by the end of the month.

 

20140711 (F) Nice Weather Lately

Leave a reply

Steven’s nephew, Spencer, was here a little after 8 AM and spent some time cleaning up the driveway.  He was joined by Tommy, who was only available for the morning.  Tommy got instructions from Steve by phone and they tried working on the retaining walls, but I’m not sure what they accomplished.  One of the large boulders Steve positioned yesterday on the lower west wall had dropped 6 inches and they were unable to re-position it.

It was another pleasant day, so I decided to work outside during the morning.  I cut up some previously trimmed tree limbs and then started pruning our apple tree.  I tried to cut all of the dead limbs and branches I could reach from the ground using our new Fiskar’s ratcheting lopper.  With that material removed I was able to use the pole saw and compound lopper to remove some larger and/or higher limbs.  By noon it was getting warm and I knocked off for the day and had lunch.  Linda made the chickpea (garbanzo bean) salad that we both like so much and served it on a bed of greens with red grapes and sweet Bing cherries on the side.

Tommy had to take off for the afternoon and left Spencer to start moving smaller rocks onto the slope of the east retaining wall.  We would occasionally hear one thud against the foundation and I decided I should check on his progress.  He was doing a fine job of tossing rocks into place, but I did not like the way the earth was pitched as it appeared to slope back towards the house.  I examined the west wall and it appeared to have the same problem.

Since the whole reason for this project was to get water to flow away from the house, I asked Spencer to take a break while I called Steve.  I told him that something just did not look right to me and that I could not see any evidence of a drain tile behind the upper wall on the west side.  He was running the excavator at another job site and wasn’t able to come look at our job so he sent Kyle over to pick up Spencer, who did not have a car.  With a chance of rain in the forecast for Saturday through Monday it is looking more and more like this job will not be done until the end of July.

In the afternoon I continued working on configuring my Windows 8.1 laptop.  My challenge today was getting Outlook 2013 to preview PDF files.  I used the search feature on the Start screen to locate information, some of which indicated I would have to create and/or edit the registry.  In the end the solution only required two steps:  installing Adobe Reader 11 and then setting it as the default program for PDFs.

With that problem solved I edited my blog posts for July 1 through 9 and started uploading them.  I managed to get the posts for the 1st, 2nd, and 3rd uploaded before dinner.  I also got a return call from Darryll at DCM Heating and Cooling and we agreed he would come to the house tomorrow at 10:30 AM to finalize the work we need done and pin down a start date to prep the house for natural gas and install a small HVAC unit for the library and a furnace for the garage.  We also need the main air-conditioner serviced.  Luckily it has been a cool summer so far.  The conversion of appliances will have to wait until the natural gas line is connected to the meter and turned on, which could be as late as early October.

I got a call from Gary at GM Construction sometime in the last few days.  He finally had all of his supplier quotes for our pole barn / bus garage project and had a price for us.  It was higher than I would have liked, but less than the quote from Morton Buildings, which was for a much smaller barn.  Last night I called Phil from Precision Grading to update him on the status of the project and to see if he would swing by and look at the pull-through driveway which the landscapers have torn up more than I expected.  My best guess is that we will get a barn up somehow, but I’m not sure when or how.

For dinner Linda made pan-grilled sliced tofu with onions and Bar-B-Que sauce served on a toasted sandwich bun with a side of lightly oiled and baked potato wedges and a few fresh strawberries.  Of course, that meant ketchup with Tabasco sauce.  We split a can of cold Yuengling beer which was the perfect beverage for this meal.  Sometime in the last two days Linda made a raspberry sauce from frozen raspberries we picked last year.  Earlier today she made a vegan chocolate cake and this evening the cake and raspberry sauce came together for dessert.

 

2014/07/09 (W) vCard Magic And Adult Tonka Toy

Leave a reply

This morning when I turned my computers on there was an update available for Adobe Creative Cloud so I let it download while we had breakfast using our new Corelle dinnerware.  Adobe updates are either very large or their servers are very slow or both.  Whatever the reason, their updates seem to take a very long time to download and install.

A couple of the landscapers arrived at 8:00 AM and resumed work on the front stairs.  It was overcast at dawn but the clouds were forecast to clear by the afternoon with temperatures in the low 70’s and zero chance of rain.  That would normally be a perfect day to work outside, if the ground wasn’t saturated with water from the recent rains.  They worked on the front stairs until lunch time, took a short lunch break, and then worked a little longer.  When they quit for the day they had all nine of the large precast steps installed and the crushed limestone base built for the brick paver sidewalk.  I think they left because there wasn’t anything else for them to do at our site until they either had some additional materials (slag and paver bricks), more crew members (for moving dirt in wheelbarrows or digging trenches by hand), or dry enough conditions to get the excavator around back ( to trench and set boulders in the retaining walls).

Linda decided not open more boxes today and focused instead on deep cleaning the kitchen, including the freezer/refrigerator, stove, and microwave and getting things ready to go to the recycling center and the Salvation Army donation center and resale store.  While all of that was going on I put a load of laundry in the washing machine and got to work on my computer tasks.  I checked my e-mail using my new ASUS laptop computer.  Everything looked OK, so I started reading and replying to e-mails on the new laptop.  That was a major milestone in that I am now committed to using the new machine as my primary computer.

With that transition in mind I spent much of the morning copying files from my old laptop to both the old and new NAS units.  I then copied critical files having to do with my websites and photographs from one of the NAS units to my new laptop.  Getting the new laptop setup with everything I need will take quite a while, but that’s OK as it also affords me the opportunity to move over only those things that I absolutely need when I need them.

I installed the vCard Wizard (vCard4Outlook) add-in without difficulty but the installation of the Duplicate Killer add-in failed.  I checked the 4Team.biz website and then e-mailed their support address.  My ASUS is running Windows 8.1 / 64-bit and apparently my Outlook 2013 is also 64-bit.  According to their website the vCard Wizard add-in supports the 64-bit version of Outlook 2013, but the Duplicate Killer add-in only supports the 32-bit version.  One of my reasons for buying vCard Wizard was that I figured the companion Duplicate Killer program from the same company would work better with it than it would with a vCard converter from another company.  If I had realized it wasn’t compatible with my configuration I could have pursued other options.

I sync’d my Palm Tungsten T3 to my old Dell laptop and then did a vCard export of all my contacts and moved it to the ASUS laptop via one of the NAS units.  From there I was able to import all of my old Palm contacts into the Contacts folder in my Personal Folder, creating duplicates if/as needed.  The Personal Folder is a carryover from my previous conversion from MS Outlook Express to MS Outlook 2007.  I am a bit unclear about the distinction between the “address book” and “contacts” within the context of MS Outlook and I am not sure I have accomplished what I intended to accomplish with vCard Wizard.  I have accomplished something for sure–my Palm contacts are now clearly in my Outlook 2013–but I thought they would be added to my address book, which does not appear to be the case.  Perhaps I chose the wrong destination folder?  More research is needed.

By 4:30 PM it was obvious the landscapers were not coming back today so that gave me the opportunity to practice using the Kobelco 35sr excavator again.  I worked for about 90 minutes digging more junk out of the woods just southwest of our house and adding it to the pile I started on Monday.  Think bricks, cinder blocks, railroad ties, landscape timbers, dimensional lumber, cut up tree trunks and large downed tree limbs and you will have the picture.  In addition to the bucket for digging and transferring material, the excavator has a claw “thumb” that can be closed to hold things in the bucket, like tree limbs, or pick things up, like boulders and cinder blocks.  It turned out that the bucket/claw combination are much stronger than a cinder block; I broke several trying to pick them up.

By the time I parked the machine and turned it off Linda had dinner ready.  She made a salad of dark greens with almonds and grapes and a barley, split pea, lentil risotto with carrot, red onion, celery, garlic, and a few chopped up greens.  We finished the bottle of Merlot we bought at Whole Foods on Saturday.  At $3 per bottle (750 ml) it was competitive with box wines like Franzia, and of comparable quality.  Although slightly dry for my taste, it was a good accompaniment to the somewhat savory dishes Linda has made this week.  I would be tempted to stock up at that price if I liked a bit more than I do.

After dinner I edited photographs on my new computer for the first time.  They will appear in the various blog entries starting with July 1st, which I will also edit and upload using the new machine.  Although the transition to a new computing platform always feels awkward for a while, and there is desire to return to the comfort of the old familiar one, from here on out I will be focused on making the ASUS my primary computing platform.

 

2014/07/08 (T) New Dinnerware

Leave a reply

I did not get all of the debris pulled out of the woods last night with the Kobelco sx35sr-3 excavator.  I was just learning how to use it so I wasn’t very efficient, and even if I had been experienced I could not have moved everything before it got dark.  I was up early this morning to get some more stuff moved before the landscapers showed up and needed it, but they beat me to the punch.

Steve showed up briefly to get the two-man crew on task and then left.  They worked on preparing and setting the next course of steps in front.  By the time they had one set it had started misting and progressed quickly to a light, steady rain.  They tried taking the excavator around back to do some trenching but the rain intensified and the ground was already very soft.  They almost got it stuck so I waved them off and made them take it back around to the front of the house.  They left shortly thereafter.  The afternoon weather was dry, cool, and breezy–very pleasant working conditions–but no one returned to resume the work.  The forecast for the rest of the week is for drier, cooler conditions, but it will take days for the ground behind the house to dry out enough that they can work efficiently and safely.

We still have a lot of unopened boxes from our move last year and Linda decided yesterday to start opening them and trying to deal with the contents.  She is always eager to get rid of things while I tend to be reluctant to part with stuff, but I am slowly coming around accepting that we have a lot of stuff we do not need, will never use, has no value, and that we have no place to store.

Her target was five boxes today.  I thought that was optimistic, but she dealt with five yesterday and five more today.  One of the boxes today had a collection of stemware with all the pieces individually wrapped in newspapers from circa 1995.  The newspaper was from our previous community, so we are the ones who packed them and obviously had them for some time before that.  We think we got them from my parents but no longer remember when or why.  Some of them may have belonged to my mother’s parents.

The discovery of the stemware led to them being washed and set out to dry followed by a re-thinking of what is stored/displayed in the kitchen/dining area.  That, in turn, led to a reconsideration of our everyday dinnerware.  We bought our Mikasa Studio Nova dinnerware a long time ago, perhaps more than 30 years, and it has served us well.  I still like the pattern; a simple round white plate with a colorful geometric edging that reminds me of the work of the Russian artist Kandinsky.  We have broken or chipped enough pieces over the years that we no longer have a complete service for more than four people, and many of the remaining pieces have developed stress lines and will eventually break.

Mikasa no longer manufactures the Studio Nova pattern and we have been looking for a replacement for the last couple of months.  We found one we liked at Bed, Bath, and Beyond but held off buying it while we continued to look.  We get 20% off coupons from BB&B regularly and when the rain let up Linda decided to go to the store in Brighton and buy the Noritaki set we liked, but came back empty handed.  It turned out that what we thought was a set of four pieces for four place settings (16 pieces) for $40 was just one place setting of four pieces.  We wanted to get 12 place settings plus service pieces, so this was not going to be our new dinnerware.

We spent some time looking at products online and found that the price of Mikasa products was similar to the Noritaki.  This changed our view of the price of Corelle dinnerware which we had also looked at and liked but mistakenly ruled out as too expensive.  We live about 11 miles from an outlet mall that has a Corning store (I know, I know, we live in a rural paradise) so we drove over there to see what they had in stock.  They had a 40% off sale on all open stock items (if you bought 12 or more pieces) and 20% off on boxed sets.

We looked at square designs and modern patterns, but decided to go with their plain Winter Frost White round product.  This is one of their longest running and broadest product lines with all items available as open stock.  They had boxed sets of five pieces for six place settings (30 pieces total) so we bought two of them to have a service for 12, and filled in an extra set of 12 medium plates, some serving bowls, and a couple of serving platters.  The simple white dinnerware makes any food look good and easy to see.  Our walls and appliances are white and our dining room table is a darker oak so the plates will both match and contrast nicely with our decor.

When we got home we opened everything and put it in the dishwasher.  While it ran Linda boxed up all of the old Mikasa pieces that were still serviceable.  She will donate them to the local Salvation Army store tomorrow.

My focus for today was purchasing and installing an add-in that allows Microsoft Outlook to import multiple vCards from a single file.  It’s really galling that I have to spend money to get Outlook to do something that it obviously should be able to do as a standard, built-in function, but there it is.  I researched plug-ins for this a few weeks ago so I revisited what I had previously found.  I finally selected the vCard Wizard (vCard4Outlook) along with Duplicate Killer, both from 4TEAM Corp.  By purchasing them together I got Duplicate Killer for 50% off.  As soon as the purchase was completed I received the downloaded links for both programs and downloaded them but did not install them right away.

Why all the bother?  My old Palm Tungsten T3 PDA can output my contacts in vCard format, but it puts them all in one file.  There are manual ways to import this data to Outlook, but it would take days instead of minutes.  I may be retired but I do not have the patience for that and have better things to do with my time; even a nap would qualify.  The problem with the manual (free) approach is that it requires you to review each contact and decide what to do with it.  I have over 1,000 contacts in my Palm and there was no way I was going to review them one-by-one.

Dr. Michael Greger (NutritionFacts.org) recently did a nice video on the research findings about the health benefits of eating yams.  Linda picked up a nice big yam at Whole Foods on Saturday and baked it for dinner this evening, topping it with black beans cooked with tomatoes and onions, and finished off with vegan sour cream.  Yes, the “sour cream” is added fat calories, but we do not use it very often.

After dinner I copied over the Outlook mailbox (.pst) files from my old Dell laptop (Win XP / Outlook 2007) to my new ASUS laptop via one of the NAS units in preparation for moving to the use of Outlook on the new laptop tomorrow morning.  I spent a while after that selecting and processing images for blog posts going back to July 1st.  I have been keeping up with writing these posts, but not with posting them.

 

2014/07/07 (M) Needs And Wants

Leave a reply

My first task most mornings is to make coffee and my second task is to eat breakfast.  Linda puts a lot of thought, time, and effort into our meals so I take my responsibility to eat them very seriously.

Bruce operating the excavator!

Bruce operating the excavator!

After breakfast I called Steve at Village Landscape to check on their plans and he said they were headed our way shortly.  He was bringing the excavator so I let him know that the retaining wall worksite behind the house was a muddy pond from last night’s rain but the front of the house looked suitable for working on the sidewalk/stairs project.  We would really like to have a front sidewalk and stairs before Ron and Mary get here on the 20th of this month.

My first computer task of the day, after starting my machines, is always to log in to RVillage and my second task is to check e-mail.  Those tasks usually recur throughout the day.  Beyond those tasks it’s whatever else needs to be done that I also feel like doing and there is often a considerable lack of congruence between those two ways of considering the tasks at hand.  At the top of both lists this morning was installing the Jetpack plug-in on the other two WordPress websites I run; the FMCA Great Lakes Converted Coaches and our personal one.  I actually managed to get this done today, but not until the afternoon.  Go back to any of the previous gallery posts and click on one of the images to see how much nicer they are to view now.

When the power flickered last night it interrupted our viewing of Doc Martin.  I was momentarily confused by that until we realized that Linda’s iPad was connected to the Amped Wireless access point in the basement which was not plugged in to a UPS unit.  It was at one point but that UPS unit failed and I had not yet replaced it so I went to the Best Buy store in Brighton this morning and bought a small APC unit.  It will be adequate to maintain power to the access point and also provide surge/spike protection for the audio equipment.  And it was on sale.  While I was out I picked up a new pruning lopper at Home Depot (a Fiskar’s ratcheting model) and some soy milk at Meijer’s.  Such is the way with tasks and errands.

The landscapers had not yet arrived by the time I got back from my errands but did arrive around noon.  Steve brought the excavator and a crew of four and they worked all afternoon on the front stairs.  They removed the old half circle step from in front of the porch, excavated for the new steps, back filled with crushed limestone, leveled and compacted it, and set the top three steps and the bottom step.  The steps are precast concrete 46″ wide, 19″ deep, and 7″ high.  They are being installed with a 17″ tread depth which is very comfortable for walking up and down the stairs.  The stairs flare out at the bottom by the driveway, so the bottom step is three of these precast units set end-to-end.  The next step up will use two of these precast units.  All of the other steps are a single unit in width.  The area between the upper steps and the lower steps will be a brick paver sidewalk.

Before Steve left for the evening he positioned the excavator over by the trash pile and walked me through the controls.  After dinner I spent a couple of hours “practicing” with the machine by picking cinder blocks, bricks, and cut up trees out of the woods and putting them in a trash pile.  The controls were “touchier” than I expected and I had a tendency to jerk the machine around rather than operate it smoothly.  I also found it tricky to coordinate the two joysticks to make it move in certain ways.  There wasn’t anything intuitive about most of the controls; certain functions are simply assigned to the two joysticks, and the buttons on them, and you have to operate it enough that it becomes second nature.  As fun as it was to play with, you would be pretty sore at the end of a long workday if you had to run this machine for a living.

Chris Dunphy and Cherie Ve Ard of Technomadia hosted another live video chat this evening for the Mobile Internet Aficionados (MIA) private/membership group.  We were going to participate but did not because I was playing with the excavator, a task that wasn’t even on my list this morning.  Membership in the group was one of our premiums for contributing to their Indiegogo crowd-funding campaign.  They used the campaign to finance the re-write of their Mobile Internet Handbook.  This is THE definitive resource for people, especially RVers, who are mobile and need to be online.  The technology is changing so rapidly that a re-write and expansion was already needed just a year after the book was originally published.

I did not accomplish all of my computer tasks today, but I did accomplish the one at the top of both my need and want lists.  It happens; sometimes.  I also got to play with a life size Tonka toy, which was very cool.  I think that is the first time I have operated a piece of construction larger than a two-person posthole digger.

 

2014/07/02 (W) Trees And Rocks

Leave a reply

Steve arrived at 6:45 AM and got right to work using the excavator to place additional large boulders for the rear retaining walls.  He was done by 8:30 AM and loaded the excavator back on his trailer to take to another job site.  I noticed that one of his trailer tires was very under-inflated so I got out my large portable air compressor to inflate it.  This tire turned out to have a puncture in the tread and was not going to hold air.  Steve knew the tires were not in good shape but I discovered that they were not an adequate load range for the weight he was carrying even if they were inflated to their maximum cold pressure, which they were not.  I inflated all of them as high as I was comfortable given their age.  If it had been my trailer I would have taken it, unloaded, immediately to a nearby tire store and had them put on four new tires with an appropriate load range.  I am not a tire expert, but we have been to enough seminars on RV tires and weight safety, that I have a better understanding of the subject then most people.

The excavator working on the rear retaining walls.

The excavator working on the rear retaining walls.

Linda made her yummy vegan pancakes for breakfast after which I decided to trim trees in the southeast corner of the yard.  It was cooler than yesterday but still a bit humid, so the working conditions were not ideal.  I worked until mid-afternoon and got one tree pruned of all its deadwood and took some low dead limbs off of several other trees.  I enjoy the pruning; it requires some thought about ladder placement, choice of tools, and where to cut, and I have a nicer/healthier looking tree when I am done.  Taking the small branches off of the larger limbs, cutting the limbs into shorter lengths, and carting everything to the fire pit; not my favorite thing to do.  Linda assures me that cleanup has never been my forte.

Two landscapers showed up around 10 AM and worked on the retaining walls.  There were supposed to be three of them, but one guy could not make it.  The hand work they were doing really needed three guys, so it was hard for them.  They got to a point where they were waiting on a delivery of sleeved plastic drain tile that wasn’t showing up in a timely fashion so I gave them directions to the Lowe’s at Grand River and Latson Roads where they bought a 100 foot roll and tied it to the roof of their car to get it back to our house.  They were then able to place the landscape fabric behind the first course of boulders, across the bottom of the shelf and up the back, lay the drain tile in the trench, and back fill the trench.  This gave them a place to stand as they worked on the next shelf.

Linda spent the morning cooking a batch of her amazing granola and her equally amazing vegan potato salad.  She boiled and then cubed red potatoes and mixed them with vegan mayo, apple cider vinegar, celery, onion, dill pickle, and dill weed.  We have been having tofu hot dogs for lunch with some regularity as it is an easy, tasty summer treat (with mustard, onions, and relish).  The potato salad was the perfect accompaniment, especially as it was still slightly warm.  Sweet cherries provided the finishing note for a tasty summer lunch.

Steve came back around 3 PM to check on the progress of his crew, gave them some specific goals for the rest of the day, and took off.  The crew was here until 6 PM.  Everyone has been working hard but we are at the stage in the project where there has been a lot more destruction than construction.  We have been through enough construction projects over the years that we know what to expect, but it is still stressful to see everything torn up.

Linda made baked stuffed acorn squash for dinner with a side of grilled baby bok choy.  The stuffing was made from carrots, celery, mushrooms, onions, sun dried tomatoes, bread cubes, raisins, walnuts, flax seeds, and sage.  It reminded me of stuffing from a Thanksgiving holiday meal.  We had a small glass of Franzia Sweet Red wine which paired well with the savory main dish.

 

2014/07/01 (T) July And Counting

Leave a reply

Well, here it is the 1st day of July, the beginning of another month, and things are just not getting checked off of the “to do” list as fast as I would like.  It finally felt like summer yesterday, and the heat and humidity erupted into severe thunderstorms overnight.  We had the house partially opened up when we went to bed with a couple of fans going in the bedroom, but I still heard the sirens when they were activated around 2:15 AM and I woke up enough to see the first flashes of lightning.  I got up and closed all of the open windows and then checked the weather on my iPad.

A storm front, which ran the most of the length of Michigan’s Lower Peninsula, was pushing east producing severe thunderstorms with up to 70 MPH winds and 1 inch diameter hail.  The storms pushed through our location between 2:45 and 3:15 AM.  There was plenty of lightning and thunder, and the trees whipped around quite a bit, but the rain was only moderate and I did not hear any hail.  By 3:30 AM the front had moved east of us and I was able to go back to sleep.

I would have liked to sleep in this morning, but I got up around 7:00 AM to make sure I was ready for the landscapers when they arrived between 8:00 and 8:30 AM.  They didn’t, and with the rain last night it’s anybody’s guess if/when they will arrive.  We moved the bus yesterday evening in anticipation of the landscapers being here early.  It was also very warm yesterday, which was easier on the engine when starting it.  I had not started the bus since we got back from the GLAMARAMA rally and with the humid conditions of the last couple weeks the auxiliary air tank had a LOT of water in it.  After I backed it up, with Linda acting as spotter, I lowered the suspension all the way down and turned off the auxiliary air compressor.  I will leave it off until I get the aux air water separator/filter replaced.  That’s one of the projects that is not getting checked off of my list as I am waiting for the landscaping to be done first.  Why?  Because once I open the air lines the bus cannot be moved until I get everything put back together.  No air, no brakes and no suspension.

I uploaded the blog posts for the last three days including a gallery post of the photos from Saturday.  I then spent some time researching alternative ways to display photos in a WordPress website/blog.  The native Gallery feature of WordPress is very easy to use, but is not very sophisticated when it comes to viewing the images.  The WordPress Jetpack includes a Carousel feature that sounded like it might be what I need.  The Jetpack makes a large collection of features available to self-hosted WordPress sites that were previously only available to sites hosted on WordPress.com.  My hesitation with the Jetpack is that I don’t need, and do not plan to use, most of its features so it potentially complicates my control panels without corresponding benefit.

Linda went to the local Salvation Army resale store in search of a highchair to keep at the house for Madeline.  They did not have any, so she tried Walmart and Target and found one she liked at Target.  She stopped at 5th/3rd Bank to make a deposit for our FMCA Great Lakes Converted Coaches chapter (GLCC) and while she was there she set up the account so she can get online statements.  Our chapter has done its banking with 5th/3rd for a while and does not pay any fees for the account.  She inquired as to the requirements for a free account and was told that the organization had to have 501(c)3 status (IRS non-profit entity).  We were looking at the IRS 501(c)7 status for the SKP Photographers BOF, which is for “social clubs,” but we will have to set it up as a 501(c)3 if we want free checking.

The landscaping crew arrived just after lunch, followed by a truck that dumped a load of very large boulders in the yard just west of the driveway.  A little while later another truck showed up and unloaded the nine pre-cast concrete steps for the front stairs.  They are 46″ W x 19″ D x 7″ thick and very heavy.  Steve showed up a little while later with his excavator, a Kobelco sk35sr-3.  He unloaded it and drove it around back to do some excavating.  He then used it to select some of the largest boulders and place them on the trailer so he could haul them to the back.  He used the excavator to unload them and roll them down the hill to where he needed them.  Steve needed the excavator on another job so he loaded it back on the trailer and left.  He came back at 9:20 PM, unloaded the excavator and used it to place a few very large boulders onto the lower shelves on either side of the walkout.  He quit at 11 PM and left the machine here so he could get an early start tomorrow morning and continue placing boulders so his crew would have work they could do when they showed up.

Pre-cast concrete steps for front porch.

Pre-cast concrete steps for front porch.

Boulders for the retaining walls behind the house.

Boulders for the retaining walls behind the house.

2014/06/30 (M) Happy Birthday L

Leave a reply

Today was Linda’s “Medicare minus one” birthday and she started it off by Facetiming on her iPad with our son and grand-daughter.  I put the coffee on to brew and joined the Facetime session.  Madeline was initially engaged in consuming a great quantity of blueberries and getting most of them in her mouth.  She was obviously feeling much better than the last time we saw her.  Breakfast was followed by a good face washing and then active exploration of the house and the wearing of adult size flip flops, which is one of the most fun things to do at the moment.  Their plans for the day included her first visit to the local water park, which has hours reserved for very small children.

Linda called the dentist’s office and got a call back just after 9 AM.  They said they could see her at 1:30 PM and she accepted the appointment.  A little while later I went outside to get the mail and discovered a fawn curled up on the door mat in front of our front library doorwall.  Its eyes were open and it was clearly alive as it watched me carefully but did not otherwise move.  I searched online and found a list of wildlife rehabilitators on the Michigan DNR website.  It was arranged by county which made it easy to locate Diane Solecki in Pinckney.  She was listed as specializing in fawns so I called her and she talked me through what to do and what to look for and directed me to her website where she had all of that information, and a lot more, for our reference.

Linda and I went out to examine the fawn according to the directions Diane gave us.  To our surprise, as soon as we started to handle it, it got to its feet, ran away to the east, and disappeared into thick cover.  That was probably unfortunate for its survival, but its odds were not very good where it was, lying exposed and very visible in the hot sun all day.  Per Diane’s instructions Linda mashed some strawberries with bread and put it over by the woods along with a bowl of water in the hope it would find it and eat and drink.  There was plenty of evidence of deer in that area so there was also some small hope that the mother might wander through there on her regular circuit and find her baby.  I checked the bowl and paper plate several times but there was no sign of it having been visited by any animals.

I got a call from Steve at Village Landscape Development letting me know they had to attend to another job first thing this morning and would be at our house around noon.  He called back around 3 PM to let me know it would be tomorrow morning between 8:00 and 8:30 AM.  It was hot and humid today, and by 3 PM the workers were drained.

Since today was Linda’s birthday, and she was still sore and tired from not sleeping well, we went out for dinner.  There is a salad shop in Brighton named Toma’s.  I had been there once and based on Trip Advisor reviews she wanted to try it.  As we were pulling out of the driveway we noticed an adult deer go into the woods to the west of our neighbor’s yard across the street.  There is a lot of evidence of deer in and around our yard and neighborhood but we only see them occasionally.  We wondered if it might be the fawn’s mother but there was no way to tell.

At Toma’s we each had a “create your own” salad with a piece of grilled pita bread.  The cook reversed our greens, but we didn’t realize it until we had each eaten half our salads. Our waitress was delightful but a bit math challenged.  I gave her $16.50 to cover a $16.29 bill and had to help her make the change.

We stopped at Staples on the way home to get a pad of large graph paper.  I am drawing plans for an alternative design for the bus barn that might make it easier for me to build myself.  Back at the house I spotted an adult deer lying down by the marsh at the NE corner of our yard near NW corner of the pond to our east.  I spent the rest of the evening editing photos from Saturday to post on our blog.  We had vegan ice cream to celebrate Linda’s birthday.

 

2014/06/25 (W) Summer Start

Leave a reply

I am normally aware of the two equinoxes and the two solstices each year and take note of their passing.  I just realized today that the summer solstice happened four days ago (on June 21st).  I checked several online sources and discovered that it occurred at 6:51 AM in the Eastern Time Zone, although it wasn’t clear if that was standard or daylight savings time.  Since that time the hours of daylight have been declining slightly each day.  Perhaps that is why I am not getting as much accomplished as I need to.  Although the summer vacation season begins Memorial Day weekend and runs through the Labor Day weekend, and climatologically “summer” corresponds to this, solar summer runs from the summer solstice to the autumnal equinox.

Linda went to the bakery today while I sat at home and waited to see if the landscape contractor would show up.  I left a message for him at 9 AM and had not heard anything by 9:30, so I headed to South Lyon to help move the SLAARC Field Day equipment out of the water tower and into Steve’s (N8AR) trailer.  We were done by 11:15 and I was about to head to Scotty’s (AC8IL) shop to return a couple of chargers when the landscaper called to let me know they would be at the house around noon.

Steve, who owns Village Landscape Development, showed up with four young men who looked up to the initial tasks that needed to be accomplished.  Three of them were not long out of high school, but the forth one, Lucas, was a few years older and more experienced.  He was the crew chief.  I indicated that we wanted to save four hosta plants, a large group of day lilies, and a large decorative grass plant, and had to show Steve where I wanted them re-planted.  I also had to indicate where I wanted the blocks from the existing retaining walls stacked.  Once that was sorted out I went inside and left them alone to do their work.

Mid-afternoon I heard the sound of Keith’s riding lawn mower and went out to check on his progress as well as the landscaping crew.  I had loaned our string trimmer and wheel barrow to the landscaping crew to clear the two slopes above the retaining walls and move the plants they were transplanting, but they needed Keith to mow the flat grass areas where they be working.  I flagged Keith down and got that sorted out with him and then went back inside and left everyone to their work.

I was not as productive during the afternoon as I would have liked to be.  I worked at my desk dealing with e-mails, RVillage groups, and computer apps, but having people at the house working is always somewhat distracting.  Linda eventually got home from the bakery and we settled into conversation about our days that took my mind off of the landscape work and other projects, at least for a while.

Steve had indicated earlier in the day that he would be back in the evening to check on the progress of the work.  His original target was 7 PM but he called around then to say that it would be around 9 PM.  He typically has 3 or 4 crews working, weather permitting.  The persistent rains this spring have carried over into summer and created big challenges for builders and landscapers.  To catch up, he puts in 14 -16 hour days.  When he got to our house at 9:20 PM there was just enough light to see and we made a quick inspection of what had been accomplished during the day.  Considering that the work did not really get underway until 1 PM, he seemed satisfied that the crew had put in a good effort and followed the directions he gave them.  That was good enough for us too.

 

2014/06/23 (M) Monsoon Season

Leave a reply

The morning was cool with temperatures just above 60 degrees F and a thin layer of high clouds.  I was tempted to work in the yard trimming low branches off a few more trees but today was supposed to be lawn care day and it did not make sense to create a mess.  That was Linda’s argument, anyway, and it sounded right to me.  Besides, the chance of rain was 0% until noon but then jumped to 60%, and the radar showed a band of storms moving out of Wisconsin over Lake Michigan and in our general direction.  Keith always mows our neighbor’s yard first, starting around 9 AM.  The first raindrops fell around 11AM.  He got part of our yard mowed but by 1 PM there was a light, steady rain, causing the grass clippings to clump and making him less than comfortable, so he called it quits for the day.  While not the steady, heavy rains of a true monsoon, late spring this year has been persistently wet.

I chatted briefly with Steve from Village Landscape Development this morning.  They have continued to be delayed in finishing projects by the recurring rain.  His newest ETA for our job was Wednesday (this week) but he was not aware of the rain that was expected for today and tomorrow.  I figure Wednesday next week; maybe.

We were sitting on the back deck enjoying our morning coffee and decided to look for some information on our Mugo Pine.  It turns out that our Mugo pine isn’t a Mugo pine after all; it’s a dwarf weeping Norway spruce.  I trimmed off a dead branch yesterday and this morning discovered that it was the right thing to do, so no harm done.  In the future I should probably follow the corollary of the carpenter’s rule: research twice, cut once.

Linda had an appointment with the dentist this morning to have her broken molar prepared for a crown.  She left mid-morning for the 50+ mile drive to Dearborn and stopped at the mall on her way back.  Between the time needed to make the crown and her upcoming jury duty she won’t be able to go back until late July to have the crown installed and all of the other work done that was postponed so the broken tooth could be dealt with last week.

Several weeks ago I bought a replacement handle and lock set for the front storm door but did not get it installed right away.  It was not a perfect fit so installation required modification of the door frame.  I’ve been putting it off but today was finally the day to get it done.  I had to drill new holes and enlarge existing ones, which never works well.  I did not get the holes in exactly the right spot the first time, which required even more drilling and enlarging.  I stayed with it and eventually got the hardware installed and working the way it is supposed to.  The trim pieces cover all of the holes, so none of my modifications are visible and the door looks fine.

I spent the afternoon at my desk catching up on posting entries to our blog and working on tasks related to several RV clubs we belong to.  I also downloaded documents and videos related to our role as RVillage Ambassadors.  The second teleconference meeting of the FMCA Education Committee today was at 4 PM, and I sent a short e-mail summary of my findings regarding the RV Trip Wizard website in advance of the meeting.  The meeting lasted 80 minutes and we had a good discussion.

We rarely go out to dinner anymore.  Besides avoiding the expense, eating at home affords us a much greater variety of ingredients prepared as healthier dishes with appropriate portions.  Tonight was an exception, though not for any exceptional reason.  Linda looked a little tired and I figured she didn’t feel like cooking, so we went to the La Marsa restaurant in Brighton.  We split an order of Koshary, a wonderful Egyptian dish with rice, macaroni, spaghetti, lentils, fried onions, and a spicy tomato sauce.  We also split the green salad that came with it, and each had a cup of crushed lentil soup.  The pocket bread was hot from the oven and the garlic spread was delicious, and it was all vegan.  Yum.

By the time we got home from the restaurant we were done working for the day.  We relaxed for a while and then turned in to watch another episode of Doc Martin.

 

2014/06/18 (W) Weather Delays

Leave a reply

We had some serious thunderstorms overnight which meant that Village Landscape Development would be delayed yet again in starting our front sidewalk/stairs and rear retaining walls drainage projects.  At this point it will very likely be early July before they start, assuming it ever stops raining.

We are expecting company tomorrow, so today was house cleaning and repair day, along with more laundry and some pole barn related work.  Gary from GM Construction finally made it over and we had a long chat about the pole barn project.  He seemed to have a good understanding of what we are trying to accomplish and a good understanding of how to get it done in Oceola Township, Livingston County, where he also lives and works.

The pole barn is proving to be a difficult and discouraging project.  Conceptually it is a relatively simple building.  In practice it is a medium-large building with very high side walls.  The trusses have to span 32 feet with 2 foot overhangs, so they will be 36 feet long and 6 feet high from the bottom cord to the ridge.  Building 16 foot high walls requires scissor lifts to do it efficiently and safely.  Getting the trusses on top of walls that high requires a crane, while securing them to the walls requires a scissor lift on each end.  I got a quote from Chelsea Lumber for the building materials and it was 80% of what we hoped to spend on the whole project.  I already have the site prep and finish grading quote and it’s a third of what we hoped to spend on the whole project.  I don’t even have prices yet for concrete, electrical, or spray foam insulation.  What this is adding up to is a project that may cost 150 – 200% of what we were prepared to spend, and I’m not sure we are prepared to do that.  That’s money I would rather put into the bus, yet the fact remains that one of main reasons for moving was to have property on which we could build a pole barn for the bus, not just to get it out of sight, but to get it out of the weather where I could work on it.  Ugh.

 

2014/05/30 (F) Outlook Contacts

Leave a reply

I have had a Palm PDA for most of the last 13 years, and for most of that time it has been a Palm Tungsten T3.  While I was still working at Wayne RESA it was synced to their GroupWise e-mail and calendar system but also synced to the Palm Desktop software on my laptop for Contacts and Tasks and my Passwords Plus program.  I did not use the Tasks list much, but I did keep all of my personal contacts, and some of my business contacts, on the Palm along with all of my encrypted passwords.  Linda also had a Palm PDA for a while and had it synced to Outlook on her office computer.  Her PDA quit working years ago and never got replaced.  Once she was settled in at the bakery she did not have a need for a PDA.

When I retired I reverted back to using the Palm calendar, which I always liked.  I even installed a new Lithium Ion battery, which was no easy job, to prolong the unit’s life.  But three things have converged to finally spell the end of the Palm era for me: 1) the unrecoverable failure of the Passwords Plus app on the Tungsten T3;  2) the porting of our home Outlook Express information into Outlook 2007 after the loss of our twmi.rr.com e-mail address, and;  3) getting a new laptop computer due to the end of support for Windows XP.

Over the winter we were able to purchase an updated version of Passwords Plus (CS 2.0) that synced through the cloud.  Versions were available that ran on our iPads, Linda’s Samsung laptop, and my then current Win XP Dell laptop.  It is also available for Android (I think) but so far we have not installed it on our phones.  The new PWP apps allowed us to successfully migrate all of our passwords from the old Palm version and make them available on four devices with back-up and synchronization via the DataViz cloud servers.  Just this past week I installed PWP CS 2.0 on my new Win 8.1 machine and got it synced with the other four.  When the passwords are available and secure, life is good.

When we moved from the previous house to the current house last year we lost our long-time home e-mail address.  I took that as an opportunity to export our home address book and all of our personal e-mails from Outlook Express and import them into Outlook 2007 on my Win XP Dell laptop.  Since that time I have continued to build out the address book with contact information, but I still have and use my Palm Contacts.  Yesterday I learned that I could export my Palm contacts in a vCard (.vcf) format.  Further research suggested that I could convert the file to a comma separated value  (.csv) format and then import it into Outlook 2013 on my new laptop.  It would be a lot more work than it sounds as the vcf –> csv conversion would require me to review each entry, but it would still be a lot less work than re-entering everything by hand.

I figured I would need the better part of a long day to accomplish this task, so before rushing into it I decided to do more research.  Today I discovered that there are add-ins available for Outlook that will take my single .vcf Palm output file and import it into Outlook directly, as long as I am willing to pony up the $$.  The idea of spending $20 -$25 for a program I will use once does not sit well with me, but the idea of sitting all day reviewing entries one at a time does not sit well with me either.  If I want to clean up duplicates, I can do that semi-automatically for another $25.  I’m thinking about it.

The calendar is another matter.  The Palm calendar can be “archived” but not exported.  My Palm calendar goes back at least a decade, and this history may just have to remain in the Palm Desktop on the old laptop.  On the upside, once I start using the Outlook calendar I may be able to set it up so I can access the address book and calendar on my Android phone.  That would be nice; I have long enjoyed having my contacts and calendar information “in my pocket,” or “on my belt,” depending on my clothing choices that day.

It was yet another beautiful day today; when Michigan weather is nice, it’s the best.  Linda decided to do some weeding in the front planting beds and I decided to install the new rear-view mirror on the bus.  You just can’t let a day like this go by without doing something outside.  After a little break we decided to work in the back yard.  We had several large pine trees that had large limbs broken over the winter.  I used our pole saw to cut those loose and dragged them over near an old burn pile.  I cut the small branches off, cut up the larger central limbs, and made a pile.  We gathered up some of the dried grass clippings from Tuesday and stuffed them under the limbs and twigs.  We added a few old, large logs to the pile that were laying around in the yard and soaked everything in diesel fuel.  Forget gasoline and charcoal starter fluid; let the diesel fuel soak in (it does not evaporate like gasoline) and put a match to it.  You will get a sustained fire.

After the fire had burned down to a smolder we moved some of the blocks from the rear retaining walls and laid them around the burn pile.  We’ve decided to use some of them to build a fire pit and wanted to see how many it would take to make a circle of the appropriate size.  We plan to build the pit 2 or 3 courses high on the low side.

Kimber, from GM Construction LLC (GM Decks), called to let me know that Gary had taken ill and would not make it out to the house late this afternoon to discuss our pole barn project.  We will try again next week.  Village Landscape Development also did not show up or call today.  I will give Steve a call tomorrow and suggest that we set a firm start date for Monday June 16.

The afternoon mail brought a Jury Summons for Linda for a two week commitment for U. S. District Court in Flint, Michigan starting Monday, June 30.  That interferes with some travel plans we have and will now likely have to adjust.  She won’t be able to find out if she needs to report on the 30th until 5 PM on Friday the 27th.