Tag Archives: toad (towed) vehicle

2015/12/28 (M) On to Arcadia

Leave a reply

Even though we were pulling out this morning we did not set an alarm to get up at some particular time.  We were up by 7:30 AM anyway. I did not make coffee or have breakfast and started preparing for departure.  We packed up our computers and put them on the bed, put away remote controls, and turned off the laser printer and NAS.  While Linda cleared off counters and secured drawers I took care of some outside things.

I pulled the tow bar parts bags out, set them aside, got out the tow bar adapters for the car, and inserted them.  I folded up the two bag chairs and put them in the car and folded up the plastic table and stowed it in the front bay.  I checked the pressure in the two front/steer tires on the bus and they were fine so I did not have to get the air compressor and hose out.  I put up all of the awnings and opened the air valve for the engine accessories and toad braking system.

When everything else was ready Linda pulled the car out while I turned on the bus chassis batteries and started the bus engine.  I let the chassis air up, pulled up the tag axle, pulled out of our site, and then backed up until I was parallel with, and close to, the edge of the road on the passenger side and not blocking anyone’s driveway.  Linda pulled the car up behind the bus and we connected it for towing.  The breakaway cable finally broke so I got the spare cable out of the glove box but I could not get the key out of the disconnect.  Rather than risk breaking it and thereby disabling the car, we decided to travel without it.

We had a final, quick chat with our neighbor’s, Danny and Dorothy, and with Ken on the other side, and pulled away around 9:10 AM.  We were out of the resort and headed southeast on US-27 at 9:26.  At Ocala we headed south on I-75 as far as exit 301 (Cortez Blvd) at Brooksville, and headed east on FL-700 as far as US-98 and headed south.  Most of this segment was also co-terminus with US-35.  The drive was mostly rural and very pretty.  It was warm outside but patchy clouds kept the temperature inside the coach from getting too warm, at least for a while.  Eventually I turned on the OTR HVAC system and it worked well.

We passed through several smaller towns but eventually got to Lakeland which was much larger, with lots of stop lights and traffic, so it took longer to get through.  Still, it was an attractive community and something to see besides an Interstate highway.  The Detroit Tigers spring training camp is in Lakeland and we will likely drive up for some games while we are in this part of Florida.

US-17 joined up with US-98 as we were leaving Lakeland.  Somewhere south of Lakeland (Fort Meade?) US-98 turned east towards Sebring and we continued south on US-17 to Arcadia.  A few miles before reaching US-70 west of Arcadia we turned onto NE Turner Road which ran due south towards the Turner Agri-Civic Center and bypassed downtown Arcadia.  We pulled into the Civic Center, which was the rally venue, at 1:15 PM.

Linda checked in with rally organizers/hosts Bill and Brenda Phelan.  Linda stayed with the coach while Bill drove me over to check out sites.  I selected site #9 which would have us facing west with our passenger side facing north.  Although this orientation put the afternoon sun on our windshields, it also provided shade in conjunction with the patio awning.  Dan (?) led us over to the site and then left us to unhook the car and back the bus in.  We leveled the coach (we thought) and I shut it down and went through our arrival preparations.

The inside of the coach was cool from the OTR HVAC and I wanted to keep it that way, so we left the windows and roof vents closed and put the insulated foil panels in the three large skylights.  We also found the snap covers for the side windows next to the driver seat and installed those.  We were able to position the coach which generous space to our passenger side and far enough back that the 25 foot shorepower cord just reached the outlet box.  After plugging in we turned on all three of the residential air-conditioners.  We deployed all of the awnings, including the patio awning, to shade the windows and provide a shady place to sit outdoors.  We also have a fresh water and sewer connection but may not use them while we are here.  We are only here until Friday or Saturday and came in with a mostly full fresh water tank and mostly empty waste tanks.

Although it was very warm (86 degrees F) and humid the clouds had thickened and filled in during the second half of our drive and there was a good, steady breeze.  The bus ran well today including the OTR HVAC.  The low pressure light only came on briefly one time while I was idling at a stop light.  Apparently it works a lot better when it is relatively warm outside.

Once we were set up we had a light lunch of roasted red pepper hummus and sourdough pretzel nibblers with fresh apple slices and orange segments.  We then drove to Walmart to pick up some anti-itch cream and bought a few grocery items while we were there.  We checked out the filling station on the property and decided it was not a good choice for our bus.  We also found the entrance to Big Tree RV Resort which was, literally, across the street from the Walmart.  We drove back towards downtown and stopped at the Winn-Dixie to see if they had a better selection of boxed wines than the Walmart.  They did, and we bought a Franzia Crisp White.  We drove the rest of the way into downtown in search of a filling station with diesel fuel, and access for large vehicles, before returning to the rally site.

Linda wanted to go for a walk so we strolled past the buses and other RVs that were already here.  We ran into Scott Crosby working on Dan’s windshield.  We met Dan, Kathy, and their son James at the FMCA GLCC Surplus and Salvage Rally back in September.  Apparently the windshield on their GM PD4106 started coming out of its gasket along the top and caving into the cockpit on their trip to Arcadia.  Scott was up on a ladder getting the gasket reseated around the frame and glass.

We continued our walk and discovered that Paul and Claudine Elbisser, also from our FMCA GLCC chapter, were here.  We visited with them for quite a while before finishing our stroll around the rally and returning to our rig for dinner.  Linda microwaved a sweet potato and served the last of the Gardein stuffed mock turkey roll and broccoli that we had for dinner on Christmas day.

After dinner I tried tuning in OTA TV stations, orienting the antenna both WNW towards Tampa St. Petersburg, and due south towards Port Charlotte, Punta Gorda, and Ft. Meyers.  When I scanned for stations I found about 60 in each direction although many of them were the same stations.  So much for digital TV signals bring highly directional.  We watched reruns of our Monday evening TV shows on CBS.  We also turned on the Verizon Mi-Fi so we could get online long enough to check TV tower locations and network affiliations, check our e-mail, and change our location in RVillage.

I got an e-mail from Gary at BCM with the draft of the February 2016 issue and a request that I proofread Part 1 of my 2-part article on our Habitat For Humanity RV Care-A-Vanner build in July 2013.  I was a little tired from our day’s activities and was not in the humor to review articles, edit old blog posts, or write new ones so I just watched TV and fiddled with the thermostats and fan speeds on our air-conditioners.  I was puzzled by the fact that it felt humid in the rig in spite of the air-conditioners having been on all day.  The front and rear ones seem to be cooling better than the middle one, but the front one was the only one that we seaw water dripping from the drain line outside the bus.  I admit to having some level of concern about where the condensed water from the evaporators is going, assuming they are condensing any moisture.

The overnight low was forecast to be about 70 with morning fog, i.e., 100% relative humidity so in spite of the fan noise we left the bus closed up and the A-Cs running.  I adjusted the thermostats down to make sure the condensers would run, and lowered the fan speed in the bedroom to reduce the noise level.  I plugged the power in for the rear OTA TV antenna, but it was not functioning correctly and was clearly not going to fix itself.  It needs to be replaced but I am reluctant to buy another one of the same model as the failure rate so far has been 50%.  Linda read, and I played a few games, on our iPads and then went to sleep.

 

2014/06/15 Family Time

Leave a reply

We were parked in a fenced compound area next to the regular “campground” at the Elkhart County 4-H Fairgrounds.  The campground has gravel sites with 50A full hookups, and we were allowed/encouraged to use the sewer connections to dump our holding tanks before departing this morning.  We had checked out the campground last night and decided that it would be easier for us to pull around to the dump stations on the outer road than to maneuver into and out of one of the open campground sites, all of which were back-ins.

I have mentioned before what a nice facility this is.  Several of our GLCC members are from north central Indiana and explained to us that the fairground is as nice as it is because it is booked every week for most of the year, winter being the exception.  Elkhart is considered the center of the RV industry in the U.S., but the reality is that RV-related industry is located throughout north central Indiana, and a little bit of southern Michigan, with a few facilities in other parts of Indiana and Ohio.  There is also significant RV industry in California, Oregon, and Florida, and to a lesser extent in Pennsylvania and Alabama.  By “RV Industry” I am referring to manufacturing, not RV parks, resorts and campgrounds, or RV dealers and service facilities, which are obviously located all over the place.

We skipped breakfast and coffee, as we always do on travel days.  Linda prepared the inside for travel and then we visited for a while with our GLCC friends.  Around 9:00 AM I unplugged the electrical power, stowed the cord, turned on the chassis batteries, opened the air valve for the engine accessories, and fired up the engine.  I did not have any trouble getting out of our parking spot or the compound.  I drove over to the dump station, which can accommodate nine RVs at one time, and Linda followed in the car.  While the holding tanks were emptying we hooked up the car for towing.  With everything stowed and secured for travel we checked the toad controls and lights and were on our way, exiting the fairgrounds at 9:25 AM.

We followed the same route home that we used when we left the Escapade rally a month ago: CR-34 (Monroe St.) east to CR-29 north to IN-4 east to IN-13 north to US-20 east to I-69 north to I-96 east to M-59 east and finally a couple of miles of dirt roads to our house.  We stopped at the Travel America (T/A) truck stop on M-60 at I-69 to put biocide and Stanadyne diesel additive in the tank along with 75 gallons of diesel fuel.

We had just over 1/4 tank of fuel indicated on the fuel gauge when we pulled in to the T/A.  If the gauge is anywhere near accurate that was approximately 50 gallons of fuel, enough to travel another 200 miles and still have 15 – 20 gallons in the tank; more than enough to get us to the Mobil truck stop on I-96 about 25 miles before our house.  I wanted to use as much of the fuel in the tank as I could before adding more but did not want to risk running out or sucking sediment off the bottom and clogging the fuel filters.  In the end we decided it was safer to stop and add fuel while we still had the 1/4 tank.  The 75 gallons brought the fuel gauge up to 5/8ths, which is what I expected.  The fuel tank capacity is 235 gallons, but I assume the full mark on the gauge corresponds to 200 gallons.  That makes every 1/8 of a tank on the gauge correspond to 25 gallons.  We also presume that our average fuel economy, based on prior data, is 6 MPG which equates to 150 miles per 1/8 tank.

We did not fill the tank because the bus is going to be sitting for a while and we did not want to have all of that fuel onboard aging in the summer heat.  There is a reason, however, to keep the fuel tank as full as possible.  Most of the fuel that is pumped to the engine is used to cool the injectors and the DDEC engine computer and returned to the tank. The more fuel in the tank, the less frequently any particular molecule passes through the engine giving the fuel in the tank more time to dissipate the heat.

Our trip was easy and un-eventful other than the powered driver-side windshield shade quite working.  Add that to the list.  We got home by 1:30 PM which gave us time to unload food and a few essentials from the bus and take showers.  Since Linda spent Saturday morning preparing food, she only had minimal cooking to do for dinner.  Our son, daughter-in-law, and grand-daughter arrived at 3:30 PM and our daughter and son-in-law arrived at 4:00 PM.  Madeline had a cold, wasn’t feeling well, and had only had a short nap, but she was fine as long as she was busy.  This was a combination birthday and Father’s Day gathering, but mostly an excuse to gather our small, immediate family.  We had a lovely summer meal of potato salad, collard greens cole slaw, baked beans, and cheeseburgers with chocolate cupcakes (from a local bakery) and fresh strawberries for dessert.  All vegan, and all delicious.

Brendan, Shawna, and Madeline left shortly after dinner and Meghan and Chris left around 8:00 PM.  Although our morning departure and drive home had been quite routine and the family gathering had been relaxed and relatively easy, it all added up to a long day.  I started the download of an update to my Adobe Creative Cloud subscription that looked like it was going to take a while, so we skipped watching an Episode of Doc Martin and turned in for the night.

 

2014/05/08(R) Toad Lights

Leave a reply

The spring peepers are in full voice this time of year, but they do not wear headlamps.  In fact, they are frogs, not toads.  In the world of RV’s a car that is towed behind a motorhome is often referred to as a “towed” (noun) or “toad.”  Like anything being towed, the car has to have functioning tail lights, brake lights, and turn signals.  The existing lights on the car are often used for this, but there can be issues with arrangement, especially on newer vehicles.

Our Honda Element came equipped with a second set of rear bulbs that are not tied into the cars lighting circuits.  On the way home from Florida they quit working.  Visual inspect had revealed that the 6-pin connector on the bus had a couple of damaged pins.  As soon as we got home I picked up a new connector from a local RV store.  With a forecast high temperature of 81 degrees F, and no rain, today was the day to install it; but not until I had taken care of another important chore.

Steve (N8AR) arrived a little after 10 AM pulling Bruce’s (W8RA) enclosed trailer.  We took a few minutes to look at my proposed site for the communications tower and then headed over to Wayne’s (KD8H) place to pick up the tower sections and related components I had purchased on Monday.  We got there right at 11AM.  Wayne greeted us in the driveway and directed us around behind the house.  We loaded the steel fold over mount, motor, rotator, and bearing plate in the front if the trailer and then drove back to where the tower sections were stored and loaded those in.  The trailer had about 10 feet inside, front-to-rear, and we were able to get everything in and close/latch the doors.  We were on our way back to my QTH by noon.  By 1 PM we had unloaded everything, stacked the tower sections on the rear/lower deck, and stored the other components in the garage.  I walked Steve through the proposed pole barn site and then he headed home to hang drywall.

I gathered up the tools I needed for the connector project and arrayed them at the rear of the bus.  Simple projects never are, and this was no exception.  I removed the two screws that hold the connector into the bumped fascia and the discovered that I could not pull it out more than a 1/4 inch.  The connector housing has an insert with the pins on one side (facing out) and the wire connections on the side (facing in).  The insert is retained by a small screw on the top of the housing.  To work on this assembly you have to be able to pull the housing out far enough to remove the retaining screw.  You then need to have enough loose wire behind the connector to allow the insert to come out the front of the housing far enough that you can get to the small machine screws that that hold the wires.

The problem was that I did not have the necessary amount of loose wire.  There was plenty of wire, it just wasn’t loose.  I had to clip about a half dozen zip ties in the engine compartment and along the underside of the rear bumper, and remove a cable clamp, but I eventually freed up enough wire to pull the connector housing out far enough to work on it.

The wire connections on the insert were not done in a standard way per the directions that came with the new connector, so I made a diagram of how they were done.  (I should have rewired both the bus connector and the cable end to be standard, but I plan to replace this whole setup with an EZ*Connector system this summer.)  I disconnected the wires, which freed the insert, and slid the old housing off the end of the wire bundle.  I cleaned up the ends of the four wires, stripping away 1/4 inch of insulation and trimming off frayed strands.  I slipped the new housing over the wires, made the connections to the back of the insert, slid the insert into the housing, and secured up it with the retaining screw.  I slid the housing back into the bumper fascia and secured it with the two screws.

Before dressing all the wires I pulled the car behind the bus and connected the electrical cable between them to test the lights.  I connected the bus chassis batteries (there are two switches for this) and turned on the left turn signal.  All the lights on the bus were fine, but I still did not have lights on the car.  🙁  I had also had problems previously with the plug and socket on the car so I jiggled the connector and the lights started working.  I verified that I had tail and turn lights but could not test the brake lights as that takes two people.  (I could have turned the ignition on and that would have caused the brake lights to come on since the emergency/parking brakes were set.)

I suspected the problem was in the connector on the end of the cable, but it was sufficiently corroded that I could not get it apart.  I decided to spray all of the old connectors (3) with De-Ox-It, including inside the cable ends.  I then sprayed all if the connectors, including the new ones, with De-Ox-It Gold.  I plugged the cable back in to the bus and the car and retested the lights.  Everything was working, so I secured the wiring on the bus with new zip ties, put my tools away, and closed everything up.

Sometime during the afternoon I got a call from Bruce (W8RA) and took a break from the electrical work.  He had a friend who had purchased a used full-size tractor to pull a large 5th wheel.  The tractor had a KVH Trac-Vision R5 in-motion satellite dish and the owner wanted Bruce to help him get it working.  Bruce knew we had a motorhome and thought I might have some insight into how to do this.  The only advice I could offer was based on the satellite dish and electronics that were on our bus when we bought it.  In addition to the dish on the roof and the receiver in the coach there was a third box that went in-between the two.  I suspected that the KVH had something similar, but I wasn’t sure.

Linda had been babysitting all day so we had an Amy’s Indian dish with a nice salad for dinner.  It had been a warm, physical day so I started a load of laundry and we just relaxed after dinner.