Tag Archives: Steve (N8AR)

2015/11/17 (T) Drivable Again

Leave a reply

Linda set her iPad alarm for 5:45 AM.  I heard it go off and got up shortly thereafter even though I did not turn out my light last night until 12:30 AM.  She got up at 6 AM and was showered, dressed, and out the door by 6:20.

I tuned in Weather Nation on WILX TV out of Lansing while I folded the clean laundry.  Of all the stations we can pick up this is the only one with a dedicated weather sub-channel.  The current forecast was for two more days with high temperatures near 60 degrees F but high humidity and rain as moisture races north from the Gulf in advance of a cold front.  By the weekend we are looking at highs at or barely above freezing and lows in the low 20’s.  The 10-day forecast has us back in the 40’s by Tuesday so we should not have any weather difficulties for Thanksgiving and the following day when we head south.

We planned to re-install the two front seats in the bus late this afternoon and I plan to take it on a fueling run tomorrow so I can run the Aqua-Hot diesel-fired hydronic heating system instead of running electric heaters.  I will also drain and refill the fresh water tank, but those are tomorrow’s tasks.  I had other things to do today, starting with the laundry.

I needed to wait until late morning to do the final cleaning of the tile in the cockpit and had several things to do that had to wait for the cleaning to be done first.  To make good use of my time I decided to measure, cut, drill, and paint the 1/2″x3/4″ aluminum angle that will serve as a retaining bracket for the refrigerator.  I will install it tomorrow after the front seats are re-installed and out of the way.

With that done I got the 3/4″ piece of walnut that Jarel cut and shaped for me to cover the front edges of the plywood under the refrigerator.  The piece sticks up a little above the top of the top layer of plywood so I wanted to install it in a way that will allow it to be easily removed.  That precluded the use of nails, even small ones.  I did not want the appearance of screw heads and wasn’t interested in drilling deep countersunk holes and using plugs.  (The woodwork in the bus was essentially assembled this way and most of the plugs have come out.  We will probably put them all back in once we are done reconditioning the wood even though I would rather not.)  That left Velcro as the only reasonable option, so I started a shopping list.

My next mini-project was to attach the 1/4″ walnut veneer plywood to the face of the pull-out pantry.  Jarel had ripped two pieces to the proper width for me but neither one was quite long enough to fully cover the front of the pull-out pantry.  Step 1 was figuring out where to have the two pieces meet and then determine how long each piece needed to be.  The next problem to solve was how to attach them.  I decided to use glue, clamp the walnut panels to the front of the pantry, and then secure them using screws from behind.  I looked for my large wood clamps but could not find them so I added face clamps to my shopping list.

The front structure of the pantry is 1/2″ thick ash and I planned to drill countersunk holes from the inside so the screw heads would be flush.  That meant I needed #6 5/8″ screws, which I did not have, as 3/4″ screws would probably puncture the veneer.  I added the screws to my shopping list.  I selected a small drill bit and drilled holes from the inside just below the top board and just below each shelf plus one just above the bottom shelf.  Because of the metal side plates these locations were easier to reach on the inside.  I then switched to my countersink bit and drilled the holes out from the inside.

Back in the garage I sprayed a second coat of black paint on the aluminum angles for the refrigerator retaining bracket, moved a load of laundry to the dryer and put another load in the washer, and then took my shopping list and went to Lowe’s.  Lowe’s had a very clever Automax self-adjusting face clamp with a 6″ reach.  It was a little pricier than the 3″ version which was a little pricier than the 3″ manual adjust version, but the size and auto adjustment feature swayed my decision.

On the drive back to house I had a nice QSO with Steve (N8AR) on the South Lyon 2m repeater.  When I got home I had some wasabi/soy almonds and sourdough pretzel nibblers with hummus for lunch.

Returning to the bus work I cleaned the tile in the cockpit using Armstrong Once ‘n Done and rinsed it with a clean sponge and warm water.  I then returned to working on attaching the walnut veneered plywood to the face of the pantry.  I decided which piece to use for the longer bottom section and which portion of the other piece to use for the top section.  In the shop I clamped each piece in turn to a 2×4, set the Boca saw guide, and trimmed them to length.

The 1/4" walnut veneered plywood clamped to the front of the pull-out pantry.

The 1/4″ walnut veneered plywood clamped to the front of the pull-out pantry.

Back in the bus I applied the bottom piece first.  It was slightly curled, lengthwise, so after applying Titebond II glue to the back I positioned it using the two Automax face clamps and then used C-clamps with scrap pieces of underlayment to hold it flat while protecting the veneer.  I then installed #6 5/8″ SR screws from the back to secure the face plywood.  I installed the upper panel using the same procedure.

We are using the same handle for the pantry that we have used throughout the bus.  Jarel made a 4-1/2″ by 8″ piece of 3/4″ walnut with coved edges to serve as a decorative base for the handle and to cover the joint between the upper and lower pieces of veneered plywood.  I marked the vertical centerline on the back and then marked two holes on 3″ centers, centered vertically.  I selected a 1/8″ drill bit, which was slightly larger in diameter than the #8-32 machine screws used to secure the handle, and drilled the holes from the back side using a block of 2×4 as a drill guide to make sure I went straight through the board.  (A drill press would obviously have been the correct way to drill these holes, and I have one, but it is buried behind other things where I cannot get to it.)

I clamped the decorative base to the front of the pantry centered horizontally and vertically on the joint between the two veneered panels.  Using the handle mounting holes I drilled all the way through the front of the pantry.  I bought special handle mounting screws the other night that are 2″ long but can be broken off at 1/4″ intervals.  I needed a 1-3/4″ length, so I inserted the screws through the holes from the back and broke off the first section with a pair of pliers.  I screwed them into the handle, temporarily securing the block.  I then drilled four countersunk holes from the inside of the pantry into the back of the decorative block and secured it with 1-1/4″ self-drilling screws.  I left all of the other clamps in place while the glue dried.

The only thing I did not get done on the pull-out pantry was attaching the door stop to the bottom of the face.  I will take care of that tomorrow.

Linda called at 3:30 PM to let me know she was on her way home.  I started working on remounting the accelerator pedal.  I got the pieces of old tile that were installed in that area and used them as templates to mark the location of the mounting holes.

Yesterday I discovered a grease fitting on the steering column.  It is located towards the center front of the bus about 8″ up from the floor.  Joe has never put grease in this fitting when he has serviced the chassis and for all I know it may not have been greased since it left the factory.  I wanted to get some grease into this fitting before I remounted the steering column shroud but I did not have a grease gun so I put that on my next shopping list.

Linda got home a little quicker than usual due to lighter than normal traffic.  After changing into her work clothes and grabbing some pretzels for a snack she came out to the bus to help.  I set the accelerator pedal upside down on top of the brake pedal to get it out of the way and drilled holes at the three points I had marked.  Linda handled the vacuum cleaner as we are trying to keep the coach clean.  I set the accelerator pedal where it belonged and started the three lag screws by hand.  Linda then held the pedal up while I tightened the three screws with a socket and ratchet.  I also drilled a small hole for a screw to secure the cable clamp on the accelerator wiring harness and installed that by hand as there was no room for the Rigid drill/driver.

I did not want to install the steering column shroud until I had greased the fitting but I went ahead and installed the base bracket.  Again using an old tile as a template I lightly marked two of the five holes.  I removed the old tile, set the bracket in place, and lined it up with the two marks.  I then marked the other three holes.  I selected a suitable drill bit, smaller than the diameter of the screws, and drilled through the tile and a little ways into the plywood below.  The screws were 5/8″ pan head Philips so I installed them by hand.

It was finally time to install the two front seats.  We got the base/pedestals from the library and checked to make sure the paint was dry.  It was, so we moved them to the bus.  I was going to install the driver’s seat first but the 3/4″ holes I had drilled in the tile when I installed it were not big enough.  Actually, they were exactly the right size if they had been in exactly the right place.  I needed to enlarge them to 1″ but did not have a 1″ drill bit.  I added that to my shopping list and we proceeded to install the passenger seat.

I set the base over the four captive mounting bolts and put a large/thick washer over each one followed by a substantial lock washer and finally a nut.  I ran the nuts down by hand as far as I could and then used a socket and ratchet to snug them down.

By now it was half past dark.  We needed dinner and stuff for the bus so we headed to Lowe’s where I bought a 1″ twist drill with a 1/2″ shank.  We then went to the new Panera, on the same property as Lowe’s and Walmart, for dinner.  This Panera had a different look and feel than the older ones, which a much smaller bakery section, but the food and coffee were the same and were good.  After dinner I drove across the street to O’Reilly’s Auto Parts and bought a grease gun.

On the drive home I decided to defer greasing the steering column until tomorrow. Our priority was getting the driver’s seat installed.  I used the 1″ twist drill bit in our 1/2″ Craftsman drill to enlarge the four holes.  The base/pedestal has 1″ long alignment tubes on the underside so the holes in the tile and underlying plywood had to be big enough to allow for less than perfect positioning.  With the holes enlarged I dropped the base in place, set a large washer over each hole, and threaded the new bolts into holes in the structure of the bus.  That was the end of the bus work for today.  We retired to the basement recreation room and watched NCIS and NCISNOLA before going to bed.

 

2015/11/10 (T) A Rainy Day

Leave a reply

I checked the TV weather station before I turned off the lights last night.  Rain covered most of Indiana and Ohio and was moving northeast.  We were going to get clipped by the western edge of the moisture but the heaviest rain was forecast to pass to our south and east.

Linda planned to go into the bakery today and had her alarm set for 5:45 AM.  It went off and I woke her up enough to shut it off and go back to sleep.  Around 6 AM we both received e-mails on our iPads and phones, a sure sign that we had lost power to the house.  I was awake at this point but stayed in bed until 6:45.  I was not falling back asleep, so I put on my robe and made coffee.  I finished up the Kenya AA, which is not decaffeinated, figuring we could both use the boost this morning.

While the coffee was brewing I cleaned the cats’ litter tray and checked my e-mail.  I had a reply from Bill Tharpe which decided for me that I would be going to Indiana on Friday.  I also had replies from the two Mitch’s who had contacted me as about articles I wrote in Bus Conversion Magazine and replied to both of those.  I edited the e-mail with the minutes of Sunday’s SLAARC meeting and forwarded it on to the club officers.  An e-mail from Gary at BCM indicated that they still needed a photo of Byron and Betty Pigg for the December featured bus article, so I replied and cc:d Byron.  Writing for BCM is sometimes a lot of work, but it’s a hobby for and I enjoy it so I do not mind.

It was wet outside and still raining lightly, a perfect day to sit by the fireplace in a robe and drink hot coffee.  Phil was hoping to return today with a load of screened topsoil and get it placed and graded along the edges of the driveway but said it would depend on the weather.  Once the topsoil is taken care of he will grade the driveway with his bulldozer and make sure the 40 foot long parking area is as flat and level as possible.

Linda finally got up at 8:30 and was starting to get dressed to go to the bakery when I suggested she stay home, rest, and get well.  She was immediately OK with that idea, put on her robe, and took her iPad to the living room to enjoy the warmth of the fireplace and some hot coffee.  I finished up my draft blog post for yesterday, e-mailed it to myself, and started this one.  I really cannot afford to lose a whole day of work on the bus but this is the kind of day where we like to just sit and do quiet things, or even nothing at all.  We finally finished our coffee, got dressed, and had a light breakfast at 10 AM.

Taking care of Madeline for three days and nights took a lot of Linda’s mental and physical energy and her cold took what was left.  She headed back to bed and I got my thoughts organized relative to working in the bus.  I talked to Jarel yesterday and found out that it would cost $50 to have a sheet of 1/4″ Baltic Birch plywood delivered to his shop because he did not have a regular delivery scheduled and the $50 cost of the 60″x 60″ sheet would not meet the minimum cost for free delivery.  I did not need the piece of plywood badly enough to pay a 100% surcharge to get it so that idea was off the table until next year.

My goal for today was to get a piece of SurePly underlayment cut and installed on the passenger seat platform.  Before I even started on the piece I had to resolve what to do about the four carriage bolts that are used to mount the base.  One of the four bolts has some messed up threads but I have a tap and die set and might be able to clean them up.  However, I am adding the thickness of the underlayment and floor tile plus a washer to what was there before so I wanted to use a longer bolt.  I already knew that Lowe’s and O’Reilly’s did not have what I needed and I presumed that The Home Depot did not either.

I finally went to Howell Hardware and had a good QSO with Steve (N8AR) on the drive there.  As I had been told they had a very good selection of hardware, by the piece, but they did not have fine thread carriage bolts in the 1/2″ size I needed.  I bought four of the 2″ long coarse thread bolts, four flat washers, four lock washers, and four nuts.  I also picked up a large washer to match the other three I already had for securing the central mounting stud along with two nylon washers.  That trip took over an hour out of my day before I even got started on my main task.

It took me several hours and many trips back and forth between the bus and the shop (in the garage) to get the piece of underlayment to fit just right.  I made one small mistake but the piece was large enough and complicated enough that I did not want to take the time or material to remake it.  Before I could install it I needed to get the outside end of the floor patch secured.  Yesterday I tried to screw that end to the material underneath it but the screw would not penetrate.  I scratched my head for quite a while until it occurred to me that I could use a small angle bracket attached to the vertical wood wiring chase in the forward outside corner.  I had limited access to that area, and it took me multiple attempts before I finally got the screw in, but I did.  Securing the bracket to the floor patch was a lot easier.

After securing the end of the patch I realized that the area between the front mounting channel and vertical front of the platform was slightly concave.  It was not a big dip but it was big enough that it needed to be patched.  Floor patching compound was the last thing I wanted to deal with today but it turned out to be just that, because once I applied it it had to dry for hours.  It was heavily overcast all day and my mood was correspondingly suppressed so I felt like I was doing everything in slow motion.  Based on the fact that I did not even get the piece of underlayment installed perhaps I was.

I try to keep an eye on the “house” batteries in the bus.  When I checked them this afternoon the reported voltage was higher than normal so I turned off the charger function on the Magnum 4024 to let the batteries rest and see where the voltage really was.  The DC draws on the battery bank were minimal.

I am finishing this post a couple of days later and no longer recall what Linda fixed for dinner but whatever it was I’m sure it was good.  After dinner we relaxed in the living room for a while, watched our Tuesday evening TV programs on the larger TV set in the basement recreation room, and then went to bed.

 

2015/11/08 (N) SLAARC Elections

Leave a reply

Madeline was in bed last night at 8 PM and fell asleep quickly.  We were in bed before 10 PM.  Linda fell asleep right away and I put my iPad away and turned off the light at 10:30 PM.  Good thing, too, as Madeline started coughing at 5:30 AM.  Linda got up at 6 AM and brought her into our bed.  I don’t know if she ever fell back asleep but we all stayed there quietly enjoying the warmth of the covers until 7:30 AM, by which time the house was warming up.  Hurrah for programmable thermostats!

Being Sunday morning, and having Madeline here, we were in no hurry to get up, get dressed, or get busy.  Not that we had nothing to do, we just were not in a hurry to do anything.  Linda prepared baked French toast last night, with a little help from Madeline, and let it sit overnight in the refrigerator.  She got up at 6:45 to pre-heat the oven and again at 7 to put the dish in to bake.

I got up at 7:30 and made coffee.  The downlight over the end of the counter where I make the coffee burned out last night so I replaced the bulb.  Linda set the table and took the French toast out of the oven at 8.  When she cut into it and served out pieces for each of us it was obvious that something was very wrong.  Instead of baked French toast we had inedible goo.  Linda has had very few recipe failures since we switched to a whole-food plant-based (WFPB) vegan diet but this one took first place.  She mentioned that it was a different recipe than she has used in the past and that she used an egg replacer she has not used before which did not seem to dissolve correctly last night.

Linda was willing to make vegan pancakes but I did not see any reason for her to go to that trouble.  We still had plenty of granola, part of a loaf of cinnamon raisin bread, and fresh berries, all of which made for an easy but tasty breakfast.]

Madeline plays (at) the organ. It is one of her favorite “toys” at our house.

Madeline plays (at) the organ. It is one of her favorite “toys” at our house.

After breakfast I cleared the table and then read a book to Madeline while Linda cleaned off the dishes.  I turned on the fireplace and we drank our coffee in the living room while Madeline found various things to play with, ultimately ending up at the organ.

By 9:30 AM we were feeling like getting dressed.  I put in my work clothes and finally got to work in the bus at 10 after turning up the thermostats in the library, garage, and bus.  The first thing I needed to do was screw down the last/top layer of SurePly underlayment in the landing and driver area.  I used #6 SR (square recessed) self-drilling wood screws in three different lengths based on what was underneath the underlayment.  I chose to use screws rather than staples for several reasons.  The main one was that I needed the ability of the screws to pull things together.  The other reason was that I did not want to get the air compressor and stapler out for this relatively small number of fasteners.  (The SurePly underlayment for the main floor of the bus was stapled with approximately 350 staples per full 4’x8’ sheet.)

I pulled up the larger piece of SurePly one last time, measured the location of the boundary between the original bus floor and the new patch, marked the boundary on the top of the large piece, and put it back in place.  I carefully aligned the smaller piece to the stair edge and along the front and made sure the larger piece also fit correctly.  The smaller piece sits entirely on the new landing, which is 3/4″ plywood, so I secured it with 1″ screws, spacing them 2-to-3 inches apart along every edge and about 4 inches apart in the field.

The 1/2″ piece of plywood just forward of the driver’s seat was partially unscrewed and needed to be screwed back down.  Since it was installed over the original 1″ thick plywood bus floor I replaced the existing screws with 1-1/4″ screws and added more, especially along the edges.

To secure the larger piece I used 1-1/2″ screws over the patch, which was already about 1-1/4″ thick.  Over the original 1″ thick plywood bus floor I used the 1-1/4″ screws and over the 3/4″ thick landing I used 1″ screws.  I ran out of the 1″ length before I got the larger piece secured.  As much as I did not want to spend time driving around today I could not finish this task without the proper screws so around 11:15 AM I headed off to Lowe’s.  As long as I had to make the trip I looked for washers to space up the mounting bolts for the passenger seat pedestal base and nylon washers to go under the nut on the main mounting stud for the two swivel bases.  I found something that might work for the former but not the latter.

Linda and Madeline were getting ready to leave as I returned home just before noon.  Madeline was upset because Linda made her wear a sweater under her coat and she did not want to.  She is generally a cheerful and pleasant little girl but we never know when or why she is going to draw a line in the sand.  She doesn’t always or even usually get her way but she is persistent.  The tears, of course, are not the result of genuine injury and are usually quickly enough wiped away by focusing her attention on something else.  They finally pulled out of the driveway at 12:15 PM for an outing at Kensington Metropark.

I finished securing the larger piece of SurePly over the landing and then started on the next task.  I had decided to patch in an area at the end of the passenger platform where it drops down into the back of the driver area.  The area to be patched was only 12-3/4″ long and less than 4″ wide but the underlying metal was rounded over in this area and there wasn’t much I could use to attach new wood.  The area was also deep and not level.  I ended up making a sandwich with two layers of SurePly, two wood shins on top of those, and a piece of 3/4″ plywood on top.  I got all of the pieces cut and fitted and then marked them with pencil lines down the exposed edges to act as alignment marks.

I carefully assembled the sandwich upside down in the shop and screwed it together from the bottom.  I then put it in place in the bus and measured for a vertical piece with an angled rear edge to catch the outside edge of the patch and hold it up.  I secured the patch with one 1-1/2″ screw near the front and secured the vertical piece with one screw into the same piece of wood.

Building and installing this patch took a while and I was just finishing it when Linda and Madeline got home around 3:30 PM from their trip to Kensington Metropark.  By this time it was too late to start working on the underlayment for the passenger seat platform as I needed to stop working at 4 PM and get cleaned up for our amateur radio club meeting this evening.  With the little time remaining I unscrewed the top of the step and removed the two screws that held it to the rear and side walls of the co-pilot/navigator platform.  I then removed a half dozen flat head wood screws that held a piece of metal trim to the front edge of the platform.

The screws were rusted but came out.  The issue for my work was that the heads were not countersunk and stuck above the metal in a way that would interfere with installing the sheet of underlayment.  I used a 7/16″ drill bit to create tapered holes and may go back tomorrow and use my countersink bit.  I looked, but did have any appropriate screws to replace the ones I took out.  That meant another trip to Lowe’s which I could do after dinner on my way to the ham radio club meeting.

I put the two swivel pedestal/bases back in the landing and locked the bus.  I made sure everything was in the garage that needed to be and closed the overhead door.  I showered and shaved and put on clean clothes.  I then sat on the living room sofa with Madeline while Linda fixed dinner.  I worked on this post while Ms. M played games on Linda’s iPad.  It’s amazing to watch a 3-year old manipulate an iPad.  Their use of the touch screen is intuitive, which is cool, and it holds their attention in a way that other activities do not, almost to the point of obsession or addiction, which can border on troubling.  In spite of how much Madeline likes to eat, Grandma Linda had to gently take the iPad away and get her to come to the table for dinner.

As part of her food planning for this weekend Linda had picked up some mock turkey patties with gravy.  She also picked up some vegan heat-n-serve mac-n-cheese.  Those were the main course this evening along with a nice green salad and the rest of the fresh pineapple.  Dessert was going to be cake but I had to leave before it was served.

I left at 5:30 PM and drove to Lowe’s in New Hudson.  I monitored a QSO between Mike (W8XH) and Steve (N8AR) until Steve reached the meeting location in South Lyon.  I then called for Mike and we chatted until I reached Lowe’s.  I bought a box of 1-1/4′ long # 12 flathead wood screws and picked up three 40 W appliance light bulbs for the microwave in the house as the installed ones had burned out.

I got to the Witch’s Hat Depot at 6:35 PM so I had a chance to visit with my fellow hams before the meeting started at 7 PM.  Steve (N8AR) had a display set up with several different DC power meters he ordered off of EBay.  The business meeting was longer than usual because we had to elect officers for 2016.  The process was very smooth, surprisingly so actually, but still took 10 minutes.  The meeting was done by 7:20 after which the club president, Harvey (AC8NO), did a presentation on his Icom IC-7200 portable base station transceiver.

I was back home by 8:40 PM.  Madeline had already gone to bed so Linda and I had some quiet adult time to enjoy a cup of hibiscus tea.  We were both tired after long days of work and play but we did a lot today and felt good about the things we accomplished.

 

2015/09/26 (S) A Step in the Right Direction

Leave a reply

We missed our ham radio club breakfast last week because we were at an RV rally and we plan to be at another rally three weekends from now so in spite of all the work we still have to do on the bus we went to breakfast in South Lyon.  After breakfast we went to the Lowe’s in New Hudson, which is close to South Lyon, and bought a Porter-Cable 1/4 sheet palm sander.  The sander is small enough to get into corners but has an integral dust collection bag.  The bag can be removed for sanding in really tight spots, but it cuts down on airborne dust while sanding and reduces the amount of cleanup afterwards.  We have several other Porter-Cable power tools and I am generally pleased with them.

Back at the house we took care of a few chores and then got to work on the bus.  Linda continued working on stripping the old wallpaper behind the sofa while I pondered for a while about what to do before deciding to concentrate on rebuilding the landing at the top of the entry stairs.  This landing is where the pneumatic entry stairwell slide cover was installed.  Without all of that “stuff” in place the last step up to the landing was now too short and the step up to the copilot level was too tall.  More importantly, the step heights were all different, and would be a built in trip hazard if not corrected.

I determined that the 2.5″ wide poplar boards installed on edge with a 3/4″ thick plywood floor and a top layer of 3/16″ SurePly underlayment would match the top surface of the plywood in the driver’s area.  That would (should), in turn, allow me to install the new vinyl floor tiles so they bridge that seam.  I will have to reuse the plywood in the driver’s area, but worst case that will require using adhesive remover followed by floor patching compound and sanding before installing the tiles.

The landing was not “square” (of course) so I made and rechecked measurements several times.  I then built a four-sided frame that fit snugly and had the front board aligned with the face of the plastic riser.  I am going to tile the steps and I am not going to use underlayment so I needed these surfaces as aligned and flat as possible.  I will probably use floor patching compound, however, to fill the gaps before installing the tile.  I used screws to secure the frame to the adjacent vertical wood that forms the riser to the copilot level and to the base of the landing with angle brackets.

I needed a piece of 3/4″ plywood approximately 31-1/8″ x 27-5/8″ for the new landing as the old piece I took out was not in good shape and I did not want to reuse it.  I did not have any other 3/4″ plywood pieces that were large enough so I went to Lowe’s.  They did not have 3/4″ half sheets (4′ x 4′) but I bought some more angle brackets while I was there.  I then went to The Home Depot.  They also did not have 3/4″ half sheets, but they had full sheets of 23/32″ sanded plywood that looked like it would work and a nice panel saw with an employee available to operate it.  I waited while he built a complete set of closet shelving for a couple and engaged in some domestic counseling.  He then cut the plywood sheet into two 4′ x 4′ pieces and helped me load them into a cart.  I was able to get them into my Honda Element by myself and close the back hatches.  I had a nice QSO with Steve (N8AR) on the drive home via the South Lyon 2m amateur radio repeater.

Linda had long since finished working on the wallpaper and busied herself in the kitchen preparing collard greens Cole slaw and vegan potato salad.  It was somewhere between late afternoon and early evening but I still had enough light to work outside.  Linda was still busy cooking so I decided to go ahead and try to cut the plywood for the new landing.  Again, it was not a rectangle, i.e., an equiangular quadrilateral (four right angles and four sides with opposing sides parallel and equal in length) so getting the shape exactly right was tricky.

I determined that the right front corner, as viewed from the entry steps, was a right angle, or close enough to one to provide a known starting point.  I put the plywood on 2″x4″s on the flat in the driveway to elevate them so I could clamp a saw guide in place and provide clearance for the saw blade.  I measured the lengths of all four edges as best I could and placed the right front corner at a factory corner of one of the 4′ x 4′ pieces.  I marked the length of the right side and the front on the two factory edges.  The left side was longer than the right side and the rear side was longer than the front side so I marked arcs for the left and rear lengths and found their point of intersection.  If the right front corner was, in fact, a right angle them this had to result in the correct shape.  The key word in that last sentence is “if.”

I tried to confirm my layout by measuring the lengths of the diagonals on the plywood and on the bus but I could not get accurate measurements in the bus.  I triple-checked my measurements and layout then marked the guide lines for the setback on my circular saw; 6-5/8″ to the inside edge of the teeth on the blade.  Truth be told I initially marked the guide lines on the wrong side of the cut.  I started to adjust my guide board to the outside of the blade and then thought better of the idea.  The guide needed to be set up so that if the blade wandered off course it would cut into waste material rather than the finished piece.  I re-measured and marked the guide lines in the proper place, checked their location with my small square, checked with the saw, made minor adjustments, and finally made the first of two cuts.  I then repeated all of that and made the second cut.  When I set the piece in place in the bus it was a perfect fit.  I was so pleased that I had Linda come out to see it.  Sometimes I amaze even myself.

I like to quit on a high note so that was the end of our bus work for today.  We did not make dramatic progress but we kept moving and got things done that needed doing.  My work today involved a certain amount of pondering and on-the-fly engineering combined with careful, repeated measuring and accurate cutting.  This kind of work is never fast.

A beautiful sunset had developed, which meant it was getting dark, so I put a few things away and closed up the bus while Linda prepared our dinner.  She made a nice salad and heated a couple of Amy’s vegan (non-dairy) lasagna entrées.  A glass of Moscato was a welcome accompaniment and we enjoyed a second glass as we relaxed in the living room.  We got a Rockler catalog in the mail today so I looked through that.  If you are into woodworking it’s the adult equivalent of the Sear’s Christmas catalogs of yesteryear.

I called Butch at 10 PM.  It was 7 PM in Bouse, Arizona and I figured they would be done working for the day and probably already had their dinner.  The daytime highs there have been reaching 110 degrees F so Butch and the other RV Park employees have been starting work between 6 and 7 AM and trying to finish up by 1 PM.  He did not elaborate but said the situation the first two weeks has not been exactly what they signed up for.  He had already responded to an e-mail from Linda with more details so we let it go at that and talked about other things.  We wrapped up our conversation at 10:30 and I went to bed.  I was going to play a couple of games and then go to sleep but there was an update available for the iPad OS so I installed it.  9.0.1 was a big update and took quite a while to install.  I was very sleepy by the time it finished and turned out the lights.

 

2015/09/23 (W) Autumnal Equinox

Leave a reply

We were up at 8 AM, had granola for breakfast, and enjoyed our coffee in the living room by the fireplace.  I like cool mornings.

I spent some time yesterday morning, and again this morning, considering my full-frame DSLR options.  The only 50 MP “35mm” DSLR camera body on the market at this time is the Canon 5Ds/R and there is no indication that Sony plans to introduce a successor to the A99 anytime soon.  The A99 is still available, as is the vertical battery pack/grip and I am at the point where I will probably order one.  It has a 24 MP full-frame CMOS sensor, which is double the resolution of my alpha 100.  More importantly, it will accept all of my old 35mm Minolta A-mount lenses and they will work as designed.

Linda left at 9:40 AM to meet Diane at Kensington Metropark.  I gathered up the laundry, sorted it, and started the first load.  I then settled in at my desk for a while.

I e-mailed Mike (W8XH) to see if he could assist me on Saturday and/or Monday with climbing the tower to do some more antenna work.  I then e-mailed Bill Gerrie to see if he and Karen were in Michigan yet.  I pulled up the initial mockup of the October 2015 issue of Bus Conversion Magazine and proofread my article on replacing the speedometer.  Jorge had done a good job of laying it out.  I e-mailed back four minor corrections, one slightly larger one, and a general comment about the lack of space following periods.  I had an e-mail from Steve Smith (N8AR) with contact information for Yaesu Fusion technical support.

The washing machine beeped so I transferred that load to the dryer and started another one.  I noticed that it was after 11:30 AM so I cleaned the cats’ litter tray, grabbed the garbage from under the kitchen island sink, put it in the trash can, and got it to the street.  Alchin’s normally comes “around noon” but I had a feeling they had already driven by.  They were still in our subdivision, however, and stopped on the way out to empty our can.

I had another cup of coffee and updated this post.  By noon Linda had not called yet let me know she was on her way home so I headed to Lowe’s for a roll of plumber’s sandpaper.  I also picked up the paste we need to hang the new wallpaper.  On the way back to the house I stopped at Teeko’s Coffee and Tea to order some Cafe Europe half-caff blend.  Linda was home when I got back and we had a light lunch.  We have both finally taken off some of the weight we put on this past winter.  Long, hard work days with little or no lunch seem to help.

By the time we got back to work on the bus projects it was 3 PM.  It’s hard to make progress when the workday starts in the afternoon.  Today is the autumnal equinox, so it gets dark much earlier in the evening than it did in late May, June, July and even most of August.  Still, as anxious as I am to get the heat exchangers re-installed we have to deal with the wallpaper in that part of the bus first.  Linda helped me assemble the right desk base, repeating what we did yesterday with the left base.

The left pedestal base with the Aqua-Hot fan-coil heat exchanger mounted inside.

The left pedestal base with the Aqua-Hot fan-coil heat exchanger mounted inside.

We installed the metal grates on the air openings (from the inside) and then used doubled-sided tape to affix the plastic mesh to the metal grate.  We put a 1/2″ plywood spacer in the bottom and marked the locations of the mounting bracket holes and the heat exchanger.  We took the exchanger and spacer out, punched the starter holes, and drilled.  Linda cleaned the heat exchanger and used a pair of tweezers to straighten the bent radiator fins, of which there were quite a few.  We cleaned off the two copper pipe stubs that provide the inlet and outlet for the antifreeze and then attached the self-stick 3/8″ X 1/4″ dense foam weather-stripping around the front of the housing.  We mounted the exchanger to the spacer with approximately 1/8″ of the foam weather-stripping beyond the front edge of the spacer.  We put the spacer/exchanger assembly back in the base and I secured it with screws while Linda pulled it into position, compressing the weather-stripping.

Linda cleans and straightens the fins on one of the fan-coil heat exchangers.

Linda cleans and straightens the fins on one of the fan-coil heat exchangers.

I took a few photographs as we worked and took some more of the finished assemblies.  While we were working we got a call from Philip Jarrell of Precision Paving.  Phil was calling to see if we still wanted the French Drain and driveway work done.  He has been busy all summer and even more so coming into fall when folks decide they need stuff done before winter.  He had given us a quote (estimate) back in the spring but could not do the work then because the soil was way too moist.  The property has dried out nicely over the last seven weeks and he wanted to make sure he did the work yet this year if we were still interested.  I told him “yes” and he said he would call “Miss Dig” right away to get the utilities marked and then get started.

The two desk bases with the fan-coil heat exchangers installed view from above and behind.

The two desk bases with the fan-coil heat exchangers installed view from above and behind.

I think this annoyed Linda as it will be another significant expenditure, but it’s something I think needs to be done and it is not easy to get a slice of Phil’s time.  (Actually, we have done a lot of difficult work together on the bus this summer and I think she was already annoyed from working with me on the right base.)  Not taking advantage of Phil’s availability would likely mean a two-year delay in getting this work done.

This project is actually a combination of two different projects that happened to make more sense to do at the same than at separate times.  The French drain is intended to dry out the far west end of our property which has standing water in the spring and after heavy rains, and stays moist/soft for the first half of the summer.  There are a lot of trees in that area and we have lost some and are losing others.  The driveway work will give us additional parking for people visiting in their RVs and create the main approach to the location for the bus barn that I hope to eventually build.  The topsoil that Phil pulls out from the driveway will be used to fill in low spots on the west end of the property, further improving the drainage in that area.

The right desk base viewed from above/behind showing the fans mounted on the back side of the heat-exchanger.

The right desk base viewed from above/behind showing the fans mounted on the back side of the heat-exchanger.

Linda returned to stripping wallpaper in the bus while I folded the laundry and put it away.  For dinner we had a salad and more of the soup that Linda made yesterday.  After dinner Linda researched wallpaper installation while I worked at my computer and uploaded eight blog posts from the third week of July.  About the time I finished the last one Brendan called so I went upstairs and Linda put the call on speaker.  He is a couple of weeks into his position at Eastern Michigan University teaching Art History and gave us a status report on how it is going, along with news of how Madeline is doing in her new daycare program University of Michigan.

We watched Dr. Michael Greger’s 2015 nutrition research summary on Linda’s iPad.  This is an annual presentation that he does at the vegan Summerfest in Pennsylvania.  His theme this year was the top health concerns of Americans, based on a major survey that was done by one of the national survey organizations, and what nutrition research has to offer with respect to these.  As we already know, many different diseases, one common answer; whole-food, plant-based, nutrition with no animal products.  We really are what we eat, and Americans are now some of the least healthy people on the planet.  We went to sleep reaffirmed in our dietary choices.

 

2015/09/13 (N) Club Business

Leave a reply

Linda is still fighting her cold and I was up way too late last night so we slept until 9 AM this morning.  Because we were getting a late start, and neither of us was hungry, I made coffee but we skipped breakfast.

It was 51 degrees F in the bus so I turned on all three electric toe kick heaters and put on my zip front sweatshirt that I use to work in cool situations.  We took all of the freezer packs out of the house refrigerator freezer compartment and moved them to the freezer compartment in the bus fridge.  Linda also filled four large containers with water and snapped the lids on.  We put those in the refrigerator compartment on the bus, turned on the power, and put the wireless remote thermometer in the freezer compartment.

I was going to raise the front of the refrigerator until the top hinge for the freezer door just touched the ceiling of the alcove but our relatively inexpensive model apparently lacks that adjustment.  Linda was also concerned about how we will latch the doors for travel.  She remembered seeing a very clever latch for a fridge with doors like ours at the GLAMARAMA rally in early June and found a picture of it on her phone.  It is actually fairly simple and if custom made could be installed using the holes for the center hinge (between the doors) on the handle side (right side) of the fridge.

(I still like Scott Bruner’s solution best.  He devised an electromagnet system that is activated by turning the ignition on but has an override switch.  He and Tami have a cafe door, bottom freezer drawer unit.  One electromagnet holds plates on top of the cafe doors where they meet at the center of the fridge.  A second electromagnet is mounted on the right side of the lower case and holds a plate on the side edge of the freezer drawer front.  Very clever, and very fail safe.)

Bruce installs the fixed side of the piano hinge to the top of the wiring chase above the OTR HVAC duct.

Bruce installs the fixed side of the piano hinge to the top of the wiring chase above the OTR HVAC duct.

Our first construction task for today was to finish installing the built-in sofa.  This was a semi-permanent installation with everything in its final place and screwed in.  We will have to disassemble it once to finish cutting it and screening off the openings in the OTR HVAC duct and to drill the 4″ diameter holes in the vertical front panel for the circular registers.  We also need to find a pair of suitable length lifts to support the seat in the open position.  Finally, we need to find and mount some 12V DC LED lights and replace the momentary contact switches in the aft end cabinet with on-off versions.

It took us until 12:25 PM to finish the sofa (for now).  We took a brief break and had an apple for a snack.  Our next task was to put the plywood bed platform back in the coach.  That sounds simple enough but we knew from taking it out that it would be difficult to put back in.  The platform is the size of a queen size mattress, in two sections joined by a piano hinge.  It’s big, bulky, and very heavy, with no good handholds but we managed to get it into the bedroom and setting flat on the storage box base.

The physically hard part was behind us but now we had to get the fixed part of the platform screwed back down to the base, requiring us to put 18 screws back in the holes they came out of.  I rewired the aisle lights before we did that as I was easier to get to the wires.  We used two screws to index the location, checked the reveal along the length of each side, and screwed it down.  I then reconnected the two gas springs while Linda held the platform up.  I also connected the wiring for the two cargo lights but they did not come on.  I will have to change the bulbs and see if that’s the problem but for now we had more pressing tasks.

A view from near the co-pilot/navigator seat of the built-in sofa with the hinged seat base lifted up to reveal internal pieces and storage space.

A view from near the co-pilot/navigator seat of the built-in sofa with the hinged seat base lifted up to reveal internal pieces and storage space.

We went inside, each had an apple, and then returned to the bus.  I had planned to temporarily mount two 12V DC switches but did not have time to fabricate a temporary mounting plate.  We needed the switches hooked up so I just reconnected the female spade connectors on the cable to the spade lugs on the switches and draped the wires over the arm of the passenger chair.

Our next task was to temporarily install the desk.  The installation was only temporary in the sense that we would need to disassemble it to get the Aqua-Hot fan-coil heat exchangers installed in the bases.  My preference was to get the heating system configured as part of the desk installation but we ran out of time before our appointment at Coach Supply Direct.

Our first sub-task was to cut the 1/4″ Baltic birch plywood spacer to fit on the right side of the right pedestal/base.  I cut it to be shorter than the desk and not as deep as the base, which is recessed at the front to create a toe kick space.  I cut the lower back corner out so the space would fit around the HVAC duct / wiring chase.  We peeled off some clear tape from the mirrors in the right rear corner down below the level of the top of the desk and set the spacer in place.

Our next task was to redo some AC wiring to get power to the space between the pedestals and reconnect the passenger side front duplex outlet.  To get power to the interpedestal space I decided to run 2C+G (Romex) cable from the wiring chase through a hole in the bottom of the pedestal, up the inside rear left, and out through a hole in the upper rear left side.  This hole and cable will not be visible unless someone crawls under the center of the desk.

In order to get the cover/shelf in the foot well aligned with the left and right pedestal/base components I decided to use mending plates attached to the back side of the bases and pedestals.  We started with the right hand components.  I attached a plate to the back side of the left rear base projection and one to the underside of the left end of the upper bottom section of the pedestal.  We set the base in place, put the pedestal on top of it, and set the cover/shelf in place.

We carefully shifted the components until we had them aligned the way we wanted.  I then secured the pedestal to the wall (which is 5/8” or 3/4″ plywood not sure which) with a single screw through the back panel centered from side-to-side and a couple of inches down from the top edge.  We double-checked the alignment of the pieces and then secured the pedestal to the base with three screws.  The base is not screwed to the floor or anything else except the pedestal.

We set the left base and pedestal in place and fussed with the alignment for but it was already 4:15 PM.  We had planned to quit working at 4 PM to get cleaned up for our SLAARC meeting and have dinner.  We still have a lot to do tomorrow for me to be ready to leave on Tuesday morning, but it should be manageable.

We went to Panera in Brighton for dinner and both had the Edamame Soba Noodle Bowl.  It was a generous serving that was tasty and filling even though it was only 390 calories.  It was very high in sodium, a common but unfortunate problem with most of Panera’s food, so not something we would eat often.

We arrived at the South Lyon Witches Hat Depot Freight House at 6:30 PM for the monthly meeting of the South Lyon Area Amateur Radio Club (SLAARC).  We had a larger group than usual, at least 30 people.  The business meeting was brief and followed by a program by Steve (N8AR) on the Yaesu Fusion technology.  Steve and several other club members brought different radios to demonstrate and let the attendees try.

We left in time to get home by 9 PM and watch an episode of Sherlock on Detroit PBS, followed by Rick Steve’s Europe and then Music Voyager.  We’ve been working long, hard hours and it was nice to take an evening to relax and do something other than work on the bus.

 

2015/08/06 (R) Three Quarters Framed

Leave a reply

As usual, we started the day with breakfast and then enjoyed our coffee while reading and writing.  Best Pest Control showed up mid-morning to apply the second treatment for hornets, wasps, etc. so we closed up all of the windows and doorwalls while they sprayed.

We located a Wayne-Dalton facility in Livonia so I called them.  As I suspected they were the factory distribution center and would not sell to us directly.  They did, however, give me the name of one of their customers, a business in Milford named The Door Doctor that had a retail store front.  I called them and they had a 12 foot length of the required D-channel bottom weather seal for our small (8′) garage door.  It turned out that they were not actually in downtown Milford but were more conveniently located near the Milford Road exit of I-96.  When the pest control guys were done and gone I drove over and bought the seal.

Back home Linda made quesadillas for lunch and set out some yummy black grapes.  We then made an errand run to Howell.  Our first stop was at Teeko’s Coffee and Tea where we ordered a pound each of fresh roasted Ethiopian Yirgacheffe half-caff and Costa Rican half-caff beans.  The Yirgacheffe is one of our favorites.  The Costa Rican is something new for us.

Our next stop was The Home Depot for a half sheet (4′ x 4′) of 3/4″ plywood.  They only had one type in a 4′ x 4′ size and I did not like it so we did not buy it.  They had nicer plywood in full sheets (4′ x 8′) but I did not need that much and did not want to fuss with something that size.  We did, however, find a drawer/cabinet pull that we liked and bought one to try out with our bus cabinets.  It’s a Rockefeller style from Liberty in an antique brass finish for a 3″ center-to-center hole spacing.  They also had a matching single screw knob in case we need it.

Our next stop was the Howell Art and Frame shop in downtown Howell to pick up three of our four pieces of artwork.  The owner, Rick, had ordered the fourth frame the wrong size and had to reorder it.  The three that were finished looked very nice and I would like to think that the artist, Ann Metzger, would have been pleased with our choices.  Ann was married to my mother’s cousin and took up painting as rehabilitation therapy for breast cancer surgery in her early 40’s.  She turned out to be quite good and was active in the St. Louis artist’s guild for many years.  We have collected many of her works over the last 44 years.

We stopped at Lowe’s to look at their drawer pulls but they did not have anything similar to the one we got at The Home Depot.  We stopped back at Teeko’s to pick up our coffee order and then headed home.

Back home we moved the paintings to the library and turned our attention to installing the seal on the 8 foot wide garage door.  With the door all the way up we were able to slide the old seal out towards the larger door.  I thought we could install the new one with the door in the same position without removing the track from the bottom of the door.  That was, indeed, the case but it did not go in easily.  I trimmed the ends and ran the door up and down a few times and made minor adjustments on each end until it worked properly.  We still need to redo the side and top seals for both doors.

I tried programming the garage door remote control in my car the day we installed the new opener on the small garage door but wasn’t able to.  At the suggestion of the woman at The Door Doctor, I Googled the model numbers of our various remotes and found the manuals.  I had forgotten that the four 3-button remotes we bought a couple of years ago had to be configured before they could be paired with the openers.  Once I knew how to do that I was able to program mine and Linda’s to work with both doors.  Each of our children also have one and I will have to re-program those the next time they are here.

I exchanged e-mails with Josh at Coach Supply Direct about picking up the extra fabric we ordered, perhaps next Tuesday.  I also e-mailed and texted with Jarel about picking up the desk pieces next Tuesday and possibly the pieces for the built-in sofa.  He did not, however, receive the mailing tube with the drawings and cut sheet today, so we will see if that works out.  I suggested he defer work on the pull-out pantry in favor of the sofa pieces as that will allow me to keep working while he is on vacation at the end of this month.  He still owes us a price estimate for the pantry but at this point it almost doesn’t matter as he will be the one building it regardless of the number.

I talked to Terry at A-1 Upholstery in Elkhart regarding the sofa cushions.  She and her mom, Lou, run the business.  I last talked to Terry in early June and she remembered the conversation.  I described once again what we were looking for and she gave me a rough estimate of the cost.  She said we could stop by Tuesday morning to drop off the fabric and discuss the job and thought they could have it finished by the end of August.  That would be great timing for us.  We are starting to feel like this whole project will come together nicely once we get the refrigerators swapped and can finely get back to work on the floor of the bus.

I installed the new Morgan M-302N I.C.E. style lightning arrestor and connected the radio and antenna cables.  I had a short QSO with Mike (W8XH) via the South Lyon 2m repeater and had no issues on transmit or receive.  I started working on a gallery post of 45 photos from the ARRL Field Day event at the end of June but only got half of it done before dinner.

Linda made a delicious zoodles dish for dinner.  Zoodles are zucchini noodles that she cuts with her SpiraLife slicer and uses in place of grain or rice pasta.  The dish had the usual garlic, onion, olive oil base but also had shallots, mushrooms, kale, and sun-dried tomatoes.  We had fresh watermelon later for dessert.

After dinner I finished the gallery post while monitoring the Novi and South Lyon repeaters.  I then had a long QSO with Mike (W8XH) and Steve (N8AR) that gave me a chance to test the M-302N lightning arrestor on both VHF and UHF at three different power levels.  We continued to have the minor problem with quick, apparently random, audio dropouts on our Yaesu FTM-400 dual band radios.  The apparent randomness has made it difficult to puzzle out what might be causing this and we all agreed that we need to set aside time to plan and execute a systematic test and record the results for analysis.

Butch called to chat about house (bus) battery cabling and other things.  I mentioned that we would be coming down on Tuesday and would try to arrange our timing so we can stop and visit over dinner.  We then watched The Princess Bride on DVD.  It’s our all-time favorite movie and I long ago lost count of how many times we have seen it.

 

2015/08/05 (W) No Mask Wednesday

Leave a reply

Linda was up at 6 AM and left for the bakery around 6:20 AM, I think. I was more asleep than awake and did not get up until later. I wanted to do a load of laundry but needed powdered detergent which I did not have. I also needed to make a run to Lowe’s so I left to take care of my errands without making coffee or having breakfast.

I picked up a couple of 2x4s at Lowe’s that I will use to cut a pair of support arms for propping open the fixed window in the bus while we exchange the refrigerators. I was going to buy a 4’x4′ (half sheet) of plywood to cut for the base of the refrigerator alcove but did not care for the selection. I also did want to wrestle with the size and weight by myself. I will have to go back to The Home Depot with Linda to get what I need. I got my laundry supplies across the street at Meijer’s and headed home.

After unloading the 2x4s I thought I would program the remote control in my car for the new garage door opener. The procedure is very simple but much to my dismay the remote would not connect with the opener. The remote is a 3-button model made by Chamberlin, and both garage door openers are identical Chamberlin models. We have four of these 3-button remotes, one for me, one for Linda, and one for each of our children. We got the 3-button model because we have two overhead doors on our garage and plan (hope) to have a barn someday with an overhead door. All four of the 3-button remotes programmed to the large garage door without a problem and the new door opener came with a single button remote that works just fine, as did the large garage door opener. I won’t know if the problem is the opener or my remote until I can try programming Linda’s remote. If her remote will program then I know it’s my remote, but if it won’t program I still won’t know where the problem lies.

I had originally planned to mask off the interior of the bus today so I could start sanding the floor tomorrow but decided to put it off. Not only would the painter’s plastic be difficult to manage by myself, I realized that it did not make a lot of sense to tape it up in advance of doing the refrigerator swap. I was on the phone with Chuck arranging to bring our bus to his shop this weekend to take care of the refrigerators when our USPS carrier, Michelle, came to the door bearing gifts. Well, OK, they were packages, but I did not expect them until tomorrow so that made them more like gifts in my mind. One was from Amateur Electronics Supply (AES) and the other was from Morgan Manufacturing, so it was all ham radio stuff.

I went to my ham shack/office and mounted the control head for the Yaesu FTM-400 on the stand that just arrived from AES. I e-mailed Steve (N8AR) to arrange a time to test the lightning arrestor before installing it in our cable entry box. I then e-mailed Jarel to start trying to arrange a day next week to drive to his shop in Logansport, Indiana to pick up the custom walnut desk. Finally, I e-mailed Josh at Coach Supply Direct to make sure he was going to be around. I was checking out the TVFool.com website, which Steve recommended, when the art frame shop in Howell called to let us know that three of our four paintings were ready to pick up. They would have all been done but he ordered the forth frame the wrong size and had to reorder it. Linda then called to let me know she was on her way home from the bakery. So much communication, so little time.

When Linda got home we discussed going out to dinner and researched a new place that had opened in Howell. As usually happens, however, there is almost no place that serves anything we choose to eat and we ended up staying home. Linda had a couple of Boca burgers in the freezer and we had those with corn-on-the-cob and fresh fruit (peaches, nectarines, and strawberries). We eat better food, and in smaller quantities, when we dine at home.

After dinner I caught Steve (N8AR) on the radio and we agreed that I would bring the lightning arrestor over to his QTH at 8 PM. I had an e-mail related to the draft of the July issue of Bus Conversion Magazine and checked to make sure a correction had been made correctly.

At Steve’s house my lightning arrestor tested better than the previous one, and should work OK in my system, but it was very clear that there is something wrong with the design and/or manufacturing of these VHF/UHF I.C.E. units. We also came to the conclusion that the quality control testing the manufacturer was doing (if any) was inadequate to reveal the problem. I expect, however, that this one will work when I install it so if it is typical of their units most hams would not have a reason to suspect that it was flawed. Someone would have a problem with it, however, as it is clearly not usable for all frequencies from 40 MHz to 1 GHz as stated on the label. My unit has a 0.31 dB loss at 445 MHz (it should be 0.01) but has an 11.59 dB loss around 635 MHz, which is a huge factor of 16 times loos of signal, and the loss from 500 MHz to 1 GHz is unacceptably large making it useless in that range of frequencies.

Steve captured all of the data and e-mailed it to me. He then tested one of his Polyphaser lightning arrestors and sent me that data file. He also sent me the link to the VNWA software from SDR-Kits.com that I needed to work with the data file. We spent a few minutes talking about the problem we are having at home with our ham radio transmissions interfering with our OTA TV signals. He sent me a link to the free student version of the ELSIE (“L”,”C”) filter design software.

I left about 9:45 PM and called my friend, John Rauch, to see if Saturday noon would work for him in terms of our refrigerator swap. He said it would and that he would check with his son (also John) to see if he could/would also help. I will let Chuck know tomorrow that it looks like Saturday is a “go.”

Linda was asleep by the time I got home so I worked in my office until after midnight. I captured the data attached to the e-mails from Steve and then downloaded and installed both the VNWA and the ELSIE software. I then uploaded my personal blog posts for June 28, 29, and 30. I logged in to the FMCA Freethinkers website, the FMCA GLCC website, and the SLAARC website and installed updates for the themes and numerous plug-ins. With that I came back upstairs and worked on this post in the living room so as not to disturb Linda and finally went to bed around 1 AM.

 

2015/07/29 (W) Drive Shaft

Leave a reply

I had had a 9:30 AM appointment at Brighton Honda to have a drive shaft replaced and suggested that we just continue on to the Brighton Panera a half mile down the road for bagels and coffee.  Linda never refuses to go to Panera so that is what we did.  The Wi-Fi was out of service but we both bought things to read so we did not care.  We sat in the two comfy armchairs by the fireplace, which was turned on, because the temperature inside was very cool, a frequent problem with this particular Panera store.  We each had a bagel and many refills of our coffee cups and stayed long enough that Brighton Honda called to let me know my car was ready to be picked up.  We left at 12:30 PM and Linda dropped me off to retrieve the ca.

Back home we had the leftover couscous with caramelized onions and the rest of the kiwis for lunch.  Linda finalized her grocery list and headed off in search of food.  I spent the rest of the day and most of the evening working on the design/drawings for the built-in sofa.

Through the course of the day I had QSOs with Jim (N8KUE) on the Novi 440 repeater and with Chris (K8VJ), Steve (N8AR), and Mike (W8XH) on the South Lyon 2m repeater. I also installed an updated driver for the NVIDIA GPU in my ASUS laptop, installed updates on the older Sony VAIO workstation (which still has Windows XP Pro), installed updates on the Linux box, and took time out for dinner (a delicious red lentil potato curry) and dessert (very sweet watermelon).

I went back to work in my office and sent an e-mail to Mike (W8XH) concerning Windows 10.  He replied via the South Lyon 2m repeater.  We had a long chat from 10:10 PM to just after 11 PM that was joined briefly by Steve (N8AR).  There was also a group QSO taking place on the Novi 440 repeater that I listened to in the background.  After I turned the radio off and came upstairs Linda said it appeared that my ham radio transmissions were interfering with our OTA TV signals.  The antennas are on the same tower but the OTA TV antenna is mounted below the Diamond X-50N 2m/70cm vertical ham antenna so I was a little surprised that it would be causing interference.  The vertical antenna has an omnidirectional radiation pattern which resembles a donut sitting on a horizontal surface, so the location directly under the base of the antenna should be a region with very little signal.  Apparently that is not the case and I will eventually have to do something to remedy the situation.  For now, however, the solution will be to not use the radio when someone s watching television.

 

2015/07/26 (N) Rearranging

Leave a reply

I was up at 8 AM but did not make coffee as Linda was still asleep and the grinder is fairly noisy.  I put the last load of laundry in the washing machine, cleaned the litter tray (which we keep in the downstairs shower), and then worked in my office.  Jasper (the cat) came down to assist me but mostly ended up supervising.

All three monitors mounted in the ham shack using the ZioTek wall-mounted track system. The Dell is in the middle. There is a mount and room for one more monitor at the right end.

All three monitors mounted in the ham shack using the ZioTek wall-mounted track system. The Dell is in the middle. There is a mount and room for one more monitor at the right end.

I mounted the fourth (last) arm on the wall-mounted rail in our ham shack.  I swung it back against the wall to get it out of the way as I do not have a monitor that I want to install at that position at the moment.  I cleaned up the tools and staged them by the stairs and then moved the coiled coax out of the way and cleared a few things off of the desks so I could move the desks back into position.  I left them farther out from the wall than before so they were appropriately placed relative to the three wall-mounted monitors.  I then put various pieces of ham radio equipment back on the desks.

Monitors obviously need computers.  I removed the Dell Precision laptop from my computer desks, removed the computer from the combination docking station and monitor stand, cleaned all of the pieces, and reassembled it.  I set it at the left edge of the ham desks, slid it under the left monitor, and placed our old Icom IC-706 HF transceiver on the monitor platform, just for appearance sake.  We are not using thus radio at the moment but it fit nicely in that spot.

I placed the GoBox with the Icom IC-7000 HF/VHF/UHF transceiver and 12VDC power supply at the right edge of the desks, put the MFJ-998 Intelli-Tuner to its left (under the right monitor), and put the larger variable voltage DC power supply on top of it.  The time we spent yesterday determining where to mount the rail on the wall was time well spent.  The monitors are at a comfortable height for viewing when seated at the desk, tilted down slightly to avoid glare from the overhead down lights, and the bottom edges are high enough above the desk to permit sizeable equipment to slide under them.  The desks are also far enough out from the wall to make it easy to attach and manage cables.

I rearranged my primary ASUS laptop on my computer desks and checked my e-mail accounts.  I have had a discussion going on this past week with Gary at Bus Conversion Magazine about hats with the BCM logo and responded to a couple more of those communiques.  Around 10:15 AM I heard footsteps and knew that Linda was finally up so I wrapped up the work in my office, transferred the laundry to the dryer, and went upstairs.

Linda was working at her desk and was not hungry but wanted coffee.  She did not sleep well last night so I made a pot of Sumatra Manhelding which is NOT one of our half decaffeinated blends.  I got myself a bowl of granola and had a large glass of orange juice.  We spent the rest of the morning in the living room reading, writing, and menu planning.

The dinette area of our bus with the two fan-coil heat exchangers on the floor. They will go in the bases of the desk when it is installed in this corner.

The dinette area of our bus with the two fan-coil heat exchangers on the floor. They will go in the bases of the desk when it is installed in this corner.

I like to hear the grandfather clock strike 12.   Besides the charming Westminster chimes, it serves to announce that the part of the day has arrived where I am supposed to get some of the physical work on my to-do list accomplished.  Today, however, my #1 priority was to redesign the pull-out pantry so I limited my physical work to gathering up my tools from the basement and moving them to the garage, moving the bus back to its normal parking spot, and taking photos of cabinet details in the bus for Jarel.  I mixed in a little e-mail, a few computer updates, some ham radio, and time for meals, but basically I worked at my drafting board most of the day and evening.

For dinner Linda made a very tasty dish that we had not had before.  The base ingredient was rice and she used basmati even though the recipe called for brown.  I prefer basmati rice to brown rice so it was a good substitution as far as I was concerned.  The other ingredients were garlic, power greens, mushrooms, and blanched fresh green beans.  She sliced and caramelized a large onion and used it as a topping.  This was essentially a “1-pot” dish in that all of the ingredients ended up combined prior to serving.  Linda makes a lot of dishes like this and we both like them. This particular dish had the crunch of the green beans, the chewiness of the rice, and the soft earthy character of the mushrooms held together by the garlic and olive oil and topped with sweet earthiness of the caramelized onions.

At 8 PM local (EDT) I participated in the weekly SLAARC Info Net for the first time in a couple of years and did so from the comfort of our ham shack.  It was a pleasure using our new Yaesu FTM-400DR/DE dual band transceiver with our Diamond X-50N 2m/70cm antenna at a height of 40 feet and connected by good coaxial cables all the way through.  Club president Harvey (AC8NO) served as net control operator and did a nice job.

After the net wrapped up at 8:45 PM Steve (N8AR), Andy (N8DEV), and I chatted for another 20 minutes trying to find some rhyme or reason why our Yaesu FTM-400’s are experiencing random audio dropouts.  We did not get it figured out and wrapped up our QSO so Steve and I could check into the LARK (Livingston Amateur Radio Klub) net that started at 9 PM (EDT).  This was the first time I had checked in to this particular net even though LARK is based in Howell and the repeater is closer to us than the ones in South Lyon or Novi.

The LARK Net was much briefer than the SLAARC net and concluded at 9:16 EDT.  Steve and I went back to the South Lyon repeater where Paul (N8BHT) heard us and joined the conversation.  When we finally wrapped up our testing QSO I went back to work on my pull-out pantry drawings.  I was about to shut everything down at 10:45 PM EDT when Mike (W8XH) announced his presence on the South Lyon repeater.  He was mobile but full-quieting and I did not experience any dropouts during our 25 minute QSO.  I took a few minutes to e-mail Jarel and then called it a night.  I had a few almonds as a snack, got ready for bed, and worked on this bog post for a while.

 

2015/07/23 (R) Wrapping Up Mara

Leave a reply

Mara’s plan was to make this the last full day of her visit.  Our day started without her as we had cinnamon raisin toast, juice, and coffee for breakfast.  I got a call from Jarel with clarifying questions and ideas about the desk and the pull-out pantry.  After a thorough discussion we had better ways to approach a few things.  He also had a better feeling for the estimated cost of the project and I agreed to send him 50% as a deposit.

I typed up a short letter and printed off the graph that Steve made of the return loss for the M-302N V/U lightning arrestor.  I packed the unit for shipping to Morgan Manufacturing and included the letter and graph.  Linda wrote out the check for Jarel and got it in an envelope to mail.  She then went to the library, Post Office, and Humane Society where she donated cat and dog paraphernalia that we had accumulated over the years.

While Linda was gone I worked in the bus for a while and Mara worked on travel preparations.  I started by removing the old 3/4″ plywood floor from the refrigerator alcove.  The original plywood bus floor appeared to mostly be in good condition but I will put a new secondary floor in the alcove to keep the refrigerator legs above the level of the new tile floor.  There are a LOT of wires running along the floor of the alcove at the back wall and I may fashion a cover for them and seal up the holes at either end.

I removed the AC dimmer for the living room lights and the DPDT momentary contact DC switch from the floor-mounted walnut box where they were installed.  The DC switch controlled the passenger side sofa footrest.  I had to remove the wires from both switches to get them out.  The AC dimmer was easy but the DC switch had four different color wires with spade connectors.  I made careful note of which terminal each color went to and then pulled the spade connectors off.  With the switches out I was able to remove the box and its mounting cleats from the floor and wall.  This area will be tiled and the box will not be reused.

Out of curiosity I tested the switch with an Ohm meter to see how the terminals were connected internally.  I also checked the wires with a DC volt meter to see how they were being used.  Two of the wires were +12VDC and DC ground and the other two went to a connector that was originally plugged into the footrest.  The switch applied 12VDC to the two load wires in one position and reversed the polarity in the other position, making the footrest go out or in respectively.

Last year I had removed two blank outlet covers on the walnut panel next to the co-pilot seat so I knew that these two switches were originally installed there and subsequently moved to the floor-mounted box.  I unscrewed the 1/4″ walnut veneered plywood panel from the wall to see what was behind it.  What I found was a LOT of wires and it was not a pretty sight.  I re-installed the two switches in their original locations and re-routed some other wires so they went up over the HVAC chase.

There was still a large bundle of wires running along the floor at the base of the HVAC chase that I needed to re-route but I decided not to mess with those today.  They are connected to four different switches and a doorbell and disconnecting everything was going to require careful attention to detail.  I pondered the refrigerator some more and decided there wasn’t anything else I could do with it for now and that I was done working in the bus for today.

There is too much to do at the moment to just sit around so I decided to install the new garage door opener for the small garage door.  New is relative; it has been sitting in the garage in its original packaging since we moved into the house, supplied by the previous owners.  The old one has not worked correctly since we moved in and the previous owners bought the new one but ran out of time to install it.  It turned out to be rather more complicated than I expected, with very comprehensive assembly and installation instructions.  It also turned out to be a two-person project so Linda worked on it with me.

We were working and Mara had started prepping dinner when a UPS truck showed up with four boxes.  The delivery included:  Mara’s refrigerator vent cover; the Cutco knives and scissors, and; the ZioTek track system for wall-mounting the monitors in the ham shack (2 boxes).  The vent cover was due for delivery today but the knives were not due until tomorrow, so we were really glad to see them as two of them were for Mara.  The monitor mounting system was also due for delivery today but I had temporarily forgotten about it.

The north wall of the ham shack/office. This is where the ZioTek wall-mounted monitor mounting system will go.

The north wall of the ham shack/office. This is where the ZioTek wall-mounted monitor mounting system will go.

Mara was understandably anxious to see if the vent cover fit her base properly.  It was a VentMate and appeared to be identical to the old one.  She climbed up the ladder on the back of her motorhome and I handed parts and tools up to her.  I then climbed up was well.  She removed the old cover and we set the new one in place.  It was a perfect fit!  We put a small amount of putty under each screw head and then ran them down snug and congratulated ourselves on another job completed and well done.

With Linda’s help we put Mara’s kayak back in its custom carrier which fits in the receiver on the back of her motorhome (she does not tow a car).  The carrier was built by a welding shop in Mesa, Arizona to Mara’s specifications and is made from 2″ square tubular steel and powder-coated black.  The carrier holds the kayak diagonally across the back of the motorhome from lower left (driver’s side) to upper right.  The nose of the kayak sits in a pocket near the driver side rear corner of the motorhome and the midpoint is nestled in a much larger cradle.  A strap runs from the nose pocket up to the midpoint on one side and across the kayak to the other side where it is attached to a ratchet and has a hook on the end.  With the hook engaged in a ring the strap is ratcheted tight and the kayak is secure for travel.  Mara runs an anti-theft cable through an eyelet near the nose and attaches a lock for safe keeping.  The tail sticks up higher than the top of the roof-mounted air-conditioner covers but does not extend beyond the passenger side wall.  The tip of the kayak is 13′ 2″ from the ground.

We made good progress on the garage door opener but had to stop at the point where we needed to attach the motor housing to the ceiling as I needed to get some parts (angle iron and lag screws) that did not come with the unit.  The front of the track was attached to the header above the door opening and we left the motor assembly resting on top of a 6 foot stepladder.

The pieces of the ZioTek monitor mounting system laid out on the floor of the ham shack/office.

The pieces of the ZioTek monitor mounting system laid out on the floor of the ham shack/office.

While Mara and Linda prepared dinner I unboxed all of the monitor mounting components.  I was curious to see the parts and wanted to make sure everything was there and undamaged, which was the case.

Dinner was Thai vegan spring rolls in rice flour wrappers.  The prep work was in the cutting of lots of veggies (carrots, zucchini, onions, red and yellow peppers, Chinese cabbage, and mushrooms).  Mara made two dipping sauces, one with ginger, hot peppers, and other things and one based on fish sauce (so we passed on that).  Linda selected our bottle of Malvasia Bianco wine from the Heart of the Desert winery in Alamogordo, NM.  It was white, which we thought would go well with the delicate spring rolls, but very sweet with a slightly thick mouthfeel, like a late harvest Riesling or a Sauternes.  Perhaps not the best choice, but we finished the whole bottle anyway.

We chatted for a while after dinner but like most of our evening meals dinner was a drawn out affair with lots of conversation.  Everyone was tired and the women turned in for the night.  I went to my office and answered e-mails from Gary at BCM that I had seen earlier in the day.  I then went to bed and tried to catch up on blog posts for the last few days but could not stay awake long enough to finish them.

 

2015/07/19 (N) Another Buddy Visit

Leave a reply

Linda was up at 6:30 AM to get showered before Madeline woke up at 7 AM.  Once Madeline was up they got busy right away making vegan blueberry pancakes.  I was up at 7:20 AM, got a quick shower, and was dressed and seated at the table just in time for breakfast.  The pancakes cooked especially well this morning although I would like to try them sometime without the blueberries cooked in.  After we were done eating I made coffee while Linda and Madeline prepared vegan sloppy Joe’s in the crock pot for lunch.

Mara has been getting up when she feels like it and eating breakfast by herself.  By 9 AM she was outside emptying the passenger side storage bays on her motorhome.  She spent the rest of the morning going through the stuff she had removed, deciding what to keep, organizing it, and putting it back.  I gathered up our laundry, sorted it, and started a load.

Aunt Meghan (our daughter) and Uncle Chris (her husband) arrived at 10 AM and I brewed another pot of coffee.  This was the second buddy visit of Madeline’s stay (the first was Cousin Katie on Friday).  Meghan provided a lot of child care during Madeline’s first 18 months and Madeline adores her “buddy.”  She took Meghan on a tour of the house showing her where various things, like snacks and kitty cats, were to be found.  It was a sure sign that Madeline is finally feeling very comfortable at our house.

Having other adults around gave Linda a break and some time to finish preparing lunch, although once Madeline realized Grandma Linda was at work in the kitchen she had to help.  I went out around 11:45 AM to fetch Mara.  We all sat down at noon and enjoyed a simple but delicious meal of vegan sloppy Joe’s (based on textured vegetable protein aka TVP), corn on the cob, raw baby carrots, and black grapes.

Madeline had very busy days yesterday and the day before and got up a little tired this morning so by 1 PM she was more than ready for her nap.  Meghan and Chris had things to do and took their leave.  Mara went back to work on her rig and Linda laid down for a nap.  I tended to the laundry and then went out to work on our bus and Mara’s motorhome.

I used the Speedout set to try and remove the screw with the stripped head from the stop block on the passenger side fixed glass frame.  I was not successful with this tool so I switched gears and worked on Mara’s cell phone booster system.  I climbed on the roof and she handed me the 12″ x 18″ thin galvanized sheet steel plate.  I took it to the front of the roof, set it down on the fore-aft centerline, and positioned the 4″ magnetic mount antenna in the center.  I dropped the coax over the edge by the driver’s side window and climbed back down from the roof.

Mara opened the sliding side window and screen by the driver’s seat and I passed the coax in to her.  Inside the rig we positioned the amplifier on the driver’s seat and started experimenting with various positions for the inside antenna.  We found one that worked well and left it for her to try.  I checked the laundry and then laid down for a nap.

I skipped dinner as I had a SLAARC meeting at 6:30 and had to leave before 6 PM which is when Madeline was having her evening meal.  Our ham radio club meetings start with social time from 6:30 to 7:00 PM.  The meeting was called to order at 7 PM by president Harvey (AC8NO) and I agreed to act as recording secretary.  Linda was not able to attend because she was taking care of Madeline so I gave the treasurer’s report in her absence.  The meeting adjourned at 7:10 PM.  We reconfigured the room for the program which was a presentation and debrief of our recent field day activity.  Larry (K8UT) reported on the N1MM Logger Plus networked computer logging software.  Steve (N8AR) reported on the radios and antennas and conducted the debriefing.

I got back home before 9 PM.  Madeline was asleep and the ladies were each enjoying a glass of Pinot Grigio on the back deck.  I poured one for myself and joined them.  The mosquitoes eventually appeared and we retreated indoors.  I reheated the bowtie pasta from the other night and finished it for dinner.  We said “good night” at 10 PM after which I checked e-mail and websites and then headed to bed.  I wrote for a while before turning out the lights.

 

2015/07/17 (F) A High Pressure Situation

Leave a reply

We closed up the house yesterday and turned on the air-conditioning as the forecast for today was upper 80’s with humidity to match and the forecast for tomorrow is a high of 90 with very high humidity.  Linda did not sleep well again last night but that had nothing to do with the air-conditioning.  The sites where the dermatologist had removed things itched, which did not help.  Nonetheless, we were both up by 8 AM and, as usual, I made coffee and we had granola.  I prepared a travel mug of coffee and left at 9 AM for Chuck’s bus garage in Novi.  Brendan, Shawna, and Madeline were due to arrive at 10 AM and I wanted to be back as close to that time as possible.

As I was working on the design for the pull-out pantry yesterday it became very clear that I needed more accurate measurements of various details of the new refrigerator in order to make sure the doors could open and the pantry could slide in and out.  It was a good thing that I checked as the measurements were not exactly as published and the specifications did not show exactly where the doors were hinged or how much clearance they needed to swing on the hinges.  Now I know, and it is a bit more than I originally allowed for, so it was a good thing that I checked.

I got home at 10:15 AM and the trio was already there.  Mara emerged from her rig a few minutes later and joined us.  Brendan and Shawna stuck around for a while but not long enough to get Madeline down for her 1 PM nap.  They had been talking to her all week about staying with Grandma Linda and Grandpa Bruce and she was prepared.  She was busy playing with Linda and did not seem concerned when her parents left for a music festival in Chicago.  They will retrieve her on Monday.

Our older grand-daughter (and Madeline’s cousin), Katie, arrived around noon so Madeline had one of her buddies here.  Madeline enjoyed her lunch and voluntarily laid down for her nap.  Katie signed up to sell Cutco cutlery and accessory products and asked if she could come practice her sales pitch on us.  We had agreed to let her do this, of course, and Mara joined us by her own choice.  The selling involved a lot of demonstration and use of a few of the knives in side-by-comparison with our existing knives, some of which were already Cutco brand.  Linda ordered a pair of kitchen shears and a santoku trimmer knife.  Mara also ordered a pair of shears and Katie was able to throw in a birdsbeak paring knife which Mara will get as Linda has one.  They agreed to just split the cost of the total order in half.

Mara was anxious to work on the roof of her Bounder and it needed to be cleaned before it was caulked.  It was a hot, humid afternoon and pressure washing the roof seemed like the perfect use of such an otherwise miserable day.  I got out the pressure washer and hose and got it hooked up.  Mara put on her bathing suit and we both climbed up on the roof of her motorhome.  I adjusted the spray nozzle to a fan pattern that would clean from 12″ away without damaging anything, showed her how I would approach the job, and left her to do the work.  Actually I sat in the shade on the porch, offered helpful advice, and occasionally moved the pressure washer.

Madeline finished her nap while we were working and came outside several times with Linda to see what we were doing.  She and Linda walked around the back yard and saw geese and a snake.  They also saw a young deer from our bedroom doorwall.  Our home in the country is a different and exciting place for her as it is for us.

When Mara was done spraying off the roof I sprayed off the sides of the rig to rinse off the dirty water that had run down the sides.  Mara then put out the patio awning and I sprayed off both sides of it as well.  When we were done we got the hose off of the grass and put the pressure washer back in the garage.  Mara was very pleased with what she accomplished.  Not only did she get something done that needed to be done but it was another thing she took care of herself instead of paying someone else to do it.  I get that.

I worked some more in my office and then came upstairs for dinner.  Mike (W8XH) had called and confirmed that Steve (N8AR) was expecting us at 8 PM.  I left at 7:30 PM and drove to Steve’s place southwest of Howell.  Mike and I arrived within a couple minutes of one another and were there for a little over an hour.

Steve is a PhD electrical engineer who worked for Bendix and was involved in communications projects for space programs.  He has a lot of test equipment that you will not find in most ham shacks and he knows how to use it.  In this particular case he used his Hewlett-Packard Network Analyzer to do two-port radio frequency through-measurements of my two Morgan Manufacturing lightning arrestors.

The first thing Steve noticed was that the center contact on one of the N-female connectors was spread open a bit.  Unfortunately any spread is “a bit” too much.  At radio frequencies these contacts need to be tight.  We crimped the contacts back together as best we could so we could proceed with the testing, but Steve strongly suggested that I replace them with high quality parts.  As expected, based on my operating experience, the M-302N V/U arrestor did not look good when tested.  Steve captured the resulting return loss graph and put it on a thumb drive for me.  I will e-mail it to Morgan with a cc: to KF7P Metalwerks and request a new one.  If the new one isn’t any better I will request a refund.  I should not have to rebuild stuff like this and the poor performance may be a design flaw rather than a manufacturing defect.

When I got home around 9:30 PM Linda and Mara were still up and chatting away in the living room.  I joined the conversation until they both decided to retire for the evening.  I spent a few minutes in my office after that taking care of e-mails and then went to bed.  I wrote for a while but was too tired to concentrate and went to sleep.

 

2015/07/16 (R) RV Work

Leave a reply

We were up at 6 AM and by 6:25 Mara had started the engine of her motorhome to pull in the slides.  She disconnected the electrical cord and we helped her back out of the driveway at 6:40.  She was pointed west so she had to drive to the end of our street and use the circle to turn around.  Her destination was Cummins Bridgeway in New Hudson.  When she made the appointment they said the closer to 7 AM she could arrive the better.  They estimated she would be there 3 to 4 hours.

Mara's Fleetwood Bounder parked in our pull-thru driveway.

Mara’s Fleetwood Bounder parked in our pull-thru driveway.  Linda in green jacket, Mara in red.

Linda did not sleep well last night, a common side effect of eating too much too late in the evening, and went back to bed once Mara was safely on her way.  I decided to stay up and clean the coffee maker before making coffee.

I wiped out the upper housing and cleaned the nooks and crannies with Q-tips.  The upper housing is undoubtedly designed the way it is to make it structurally adequate with a minimum of plastic but it was equally obviously not designed with any consideration for being able to clean it.  Like many things, it leaves me wondering if the designers ever use the products they design or what sort of functional specifications they work from and who develops those.  I think the Bauhaus had it right when they declared “form follows function.”  My guess is that commercial equipment, while less “stylish” than consumer goods, has cleanability and serviceability as primary design considerations.

I remembered that we had a one gallon jug of distilled white vinegar in the bus so I got that and ran eight cups of it through the coffee maker.  I added four cups of water to the used vinegar and ran it through again.  I then ran 12 cups of RO water through the coffee maker.  By the time I was done it was approaching 8 AM so I ground up some of the Sumatra Mandheling beans (not decaffeinated) and made seven cups of coffee.  I normally make 8 – 9 cups but this was full-strength stuff.  I’ve been making 11 cups while Mara is here but it turns out that she does not drink much coffee so I will be back to my usual 8 – 9 half-caff servings going forward.

I enjoyed my first cup of coffee while finishing yesterday’s blog post and starting this one.  I enjoyed my second cup while researching hardware for mounting a small table to a wall so that it is essentially cantilevered, which is the table arrangement we need for the bus.  I found a 2-piece aluminum extrusion that might be the solution for attaching the table to the wall.  It is 30″ long and can be cut to length but I do not think it will not be strong enough by itself to support the table.  I found an angle bracket on Rockler that might be the additional piece I need.  It is 12″ x 18″ with a notched corner, made of 1/8″ steel, and powder-coated black.  A pair of them will support 1,000 pounds so one in the center would be more than sufficient.  An alternative would be a wood strut angling back to the wall but we are not willing to have a vertical table leg.  I have not decided whether the table should be removable but I am leaning towards a more permanent installation.

Linda eventually got up but neither of us were hungry so we did not have breakfast.  I went to my office and ordered the ZioTek monitor mounting system from CyberGuys.  I then e-mailed Ewa at AFC Industries and thanked her for the second quote but let her know that the price was way out of my budget.  I finally settled in to work on the custom desk design for the bus and eventually finished it (I think).  Linda left around 12:30 PM for her dermatology appointment.

Now that we have base station antennas cabled to the ham shack I tend to have the new Yaesu FTM-400DR/DE dual band (VHF/UHF) radio on whenever I am working in my office.  It provides a pleasant diversion from my other tasks and is actually useful.  Somewhere mixed in with everything else were a couple of QSOs with ham buddies and an attempt to coordinate with Steve (N8AR) and Mike (W8XH) about testing my two Morgan lightning arrestors at Steve’s QTH.

This toad was sitting on a rock by our front porch.

This toad was sitting on a rock by our front porch.

Our bus had settled in the rear and was clearly out of level.  The reason it had settled was that I forgot to switch the suspension system to Level Low and shut off the air to the engine accessories.  It was of no consequence but it bugged me so I started it, let it air up, re-leveled it, shut it down, and switched off the batteries and engine air accessories.

Mara returned from Cummins Bridgeway around 1 PM and I guided her back into her parking spot.  They did the routine service on her motorhome engine and generator but found several things on the genset that needed to be repaired.  She agreed to have the work done so they removed the genset from her rig and will reinstall it next Wednesday.  They also inspected the motorhome and gave her a list of other things that needed to be fixed, some right away and some eventually.  She did not have them do any of that work as she wanted me to look at the list first.  The added service work means Mara will be visiting with us for at least another week, which pleased us greatly.

I went over the list with her and we discussed the relative importance and urgency of each repair.  One of the items involved the caulking on the roof so we both climbed up there to have a look.  I also wanted to scope out how we might install her weBoost Drive 4G-X cellular booster system.  While we were on the roof I was able to rock the rig side-to-side quite a bit just by shifting my weight.  One of the other items on the diagnostic list was shock absorbers and I indicated that I thought that sounded appropriate, especially given that the back ones reportedly had cracked/broken mounts.  They also noted that the transmission fluid was low and that the filter and fluid should be replaced.  I encouraged her to have these taken care before she left as Cummins Bridgeway is a very good service facility.

The other items were things that could wait but the caulking of the roof was something Mara could do herself.  She likes to take care of as much of her rig as possible and she will be here through at least Wednesday, so she has time.

Linda got back from her out-patient surgical appointment with bandages in seven different places.  We visited for a while and then I left the ladies and returned to my office.  I started on the design of the pull-out pantry for the bus and quickly realized that the very expensive Fulterer heavy-duty pull-out pantry slide I ordered from Rockler was too wide for the space we have available.  I came upstairs and groused about it for a while until Linda and Mara urged me to try canceling the order.  I called Rockler and spoke to someone in customer service.  I won’t know until tomorrow at the earliest, and probably not until Monday, if I was successful in intercepting the order before it shipped.  If not I will have to pay to ship it back and may have to pay a restocking fee.  Although I do not have anywhere else I can use it at the moment, between the restocking charge and the cost of shipping I may just keep it and find a use for it.

Linda made a large salad for dinner and we chatted during and after the meal.  It had been an early, long, hard day for all of us.  Mara returned to her rig before it was dark and Linda headed off to bed shortly thereafter with me not far behind.

 

2015/07/11 (S) Impactful Tools

Leave a reply

We had a small crowd for our SLAARC breakfast this morning but good conversation.  After breakfast we drove to Chuck’s house and picked up the manual impact screwdriver.  Barb was up in the thumb visiting her brother-in-law who recently lost his wife (Barb’s sister).  We lingered for a while and then left for home, stopping for gas on the way.

Back at the house I started a load of laundry and then went to work on the stop block screws.  Linda helped steady the ladder and pass tools and parts back and forth.  I got three of the four screws out of the two stop blocks but the head stripped on the forth one so I was only able to remove the aft stop block.  I tried different bits and even tried drilling a small hole in the center of the head to allow the bits to go in farther but it did not work.  The next approach will be a screw extractor, but first I have to go buy one.

We had soy yogurt for lunch with red grapes and I had a few pretzels with roasted red pepper hummus.  I kept trying to get to the basement to work on the desk design but kept getting detoured.  Once I finally reached my office I found that the mouse trap that I had placed under one of my desks was out in front of it.  The food was gone but there was no mouse, only mouse poop.  I realized that the trap was upside down which allowed the door to swing open.  Our best guess is that a mouse was trapped and the cats pulled the trap out from under the desk and accidentally turned it over while pawing at it trying to get the mouse.  Since there was no sign of a mouse having been caught by one of the cats my best guess is that it escaped, for now.

I checked e-mails and found the one with the credentials and instructions for the QTH.com web-hosting of SLAARC.com so I shared those with the other members of the SLAARC website team and then logged in to check out the log file I had created the other day as a test.

I decided to reconnect the Yaesu FTM-400 radio to the Diamond X-50 antenna on the tower so I could monitor the Novi and South Lyon repeaters while I worked in my office.  I had quite a mess on the ham shack desks and decided the best way to deal with it was to install Mike’s Icom IC-2820H in my car in place of our Icom V-8000 2m rig.  At least that would get the 2820 off the desk.  I checked that the mounting brackets and they were identical so I removed the V-8000 but left the mounting bracket installed in the car.

Mike had modified the power cord on his radio by cutting off the T-connector and replacing it with Andersen PowerPoles so I had to modify the power cable in my car to match as I could not modify Mike’s radio.  I removed the fuse from the positive (+12VDC) lead and then cut off the T-connector, leaving about 6″ of wire so I can add PowerPoles and make it into an adapter cable.  I brought my Hakko soldering station up from the basement, set it up on the floor behind the center console, ran an extension cord from the garage, and used it to solder PowerPole contacts to the two wires.  I then inserted them into the black/red housing pair and snapped them in place.

I mounted the IC-2820H, connected the power cable and connected the coax from the antenna.  I reinstalled the fuse in the positive lead, started the engine, and turned the radio on.  A couple of hams were chatting on the Novi repeater, one of whom I knew (Jim, KB8TAV).  When they finished I gave Jim a call and he came back to me, the first time I have been able to use the Novi 440 repeater from my car.  Jim signed off and I switched to the South Lyon 2m repeater and gave a general call.  Steve (N8AR) came back to me and we had a short QSO that verified the radio/antenna was also working on 2m.  As we were wrapping up Linda started fixing dinner.

Linda fixed a simple salad and Dr. Praeger’s vegan hamburgers with Daiya non-dairy cheese.  These patties were also squishy rather than firm and, like the ones at Zingerman’s Roadhouse the other night, where not very satisfying.  They tasted OK, and we ate them because we are not inclined to waste food, but there is a lot more to what makes food satisfying than just taste.  Sight, smell, and texture (mouth feel) are also important.

Linda had several TXT messages from Mara letting us know that she would be arriving tomorrow sometime before 2 PM as she wanted to watch the Wimbledon finals at that time.  Linda and I considered how best to accommodate Mara’s motorhome and finally decided to just pull our bus straight forward until the nose was at the edge of the concrete driveway.  That created more than enough space on the level part of the pull-through driveway for her to park and plug in to our 50 amp service.  The only loads we have in the bus at the moment are battery chargers so we used our 15 amp cord to plug it into a garage outlet.  Since I had to start it to move I switched it to high idle once I had it positioned, leveled it, turned on the OTR air-conditioning to put a load on the engine, and let it run for 30 minutes.

I returned to my office after dinner and work on the desk design for a while but by this point I was tired and not really in the mood.  The last time I updated the BCM page on our website was after the February 2015 issue came out.  I have had articles in the March, April, and May issues and will have articles in the June and July issues.  I captured the covers from March, April, and May and updated the page.

I exchanged e-mails with several people and spent some time looking at dual and triple monitor stands on EBay.  We rarely use EBay and the site made me change our password before it would let me log in.  There was a large selection of products but none of them were exactly what I am looking for.  There wasn’t any rush so I decided to revisit this tomorrow.

 

2015/07/09 (R) Graduation Celebration

Leave a reply

My main focus this morning was my dentist appointment at 10:30 AM.  I wanted to leave the house at 9 AM so I had plenty of time to get there and actually left at 9:15.  Once I was on I-96 eastbound and clear of the construction at US-23 I called the South Lyon 2m repeater and Steve (N8AR) came back to my call.  I-96 was very slow as I approached Wixom Road so I exited at Beck Road and dropped down onto Grand River Avenue (GRA).  I got off GRA at M-5 in Farmington Hills and took that to where it ended and rejoined GRA.  I continued to Telegraph Road and headed south.  My QSO with Steve lasted until there by which point there was too much noise and not enough signal for a pleasant conversation.  In spite of the change from my intended route I was still at the dentist’s office by 10:10 AM and they were able to take me in early.

On the way home I called the South Lyon 2m repeater and Mike (W8XH) responded to the call.  As a result of differing weekend plans I decided to head to his QTH and pick up his climbing harness.  While I was there I took a few minutes to look at his reconfigured ham shack and his Canon EOS D7 Mark II DSLR.  To say that I am unhappy about Sony’s failure to release the alpha 99 II FF DSLT would be a gross understatement and I am not alone in the sentiment.

Back at the house we had a light lunch of sourdough pretzel nibblers and roasted red pepper hummus.  I then went to my office to continue working on the custom desk design for our bus.  But first I was taking care of e-mails when Williston Crossings RV Resort called back and said they had a spot for us for December.  We had not heard back from Suncoast Designers regarding an appointment to have a fogged window repaired so I called them.  They said they had replied to my e-mail letting us know that we were scheduled for December 7 but the e-mail had not come through, so I need to check the spam filter.

Linda called back and accepted the spot at Williston starting December 1st.  We will have to leave for one to three days to have the window taken care of and we will depart on the 26th for the Arcadia Bus Rally but the monthly rate will still be cheaper than paying for three weeks at the weekly rate.  Besides, they did not have a two or three week opening.

I did get a couple of hours of work done on the desk design and then had to quit.  A month ago our elder grand-daughter, Katie, missed her high school graduation due to a sudden illness.  Meghan and Chris (Katie’s dad) made reservations at Zingerman’s Roadhouse for 5:45 PM today and we gathered to celebrate this milestone in Katie’s life.  Brendan, Shawna, and Madeline also joined us and we all enjoyed quizzing (and teasing) Katie about her upcoming college experience at Northern Michigan University where she plans to major in Wildlife and Fisheries within the larger biology program.

Linda and I had the black bean burger with fresh, hand-cut fries.  Although it was tasty, and vegan, it did not have any binders and completely fell apart when I tried to assemble it as a sandwich.  We ordered them on sourdough bread as the buns had an egg wash.  Zingerman’s has excellent bread, but it is the rustic style with crusts that are so tough you cannot cut them with a knife (or a chainsaw).  Thus the “burger” was difficult to eat even as an open faced sandwich and was basically a messy pile of “stuff” on my plate.  Linda seemed to enjoy hers but I regretted ordering it even though I ate the whole thing.  I did, however, have a glass of Schramm’s Raspberry Mead made by my friend, and former colleague, Ken Schramm.  It was excellent.  The hand-cut fries were also good and the waitress was delightful, which is always a plus.

Back home I worked for a couple more hours in my office and then worked on this post.  I put my new N.T.I. dental appliance on my lower front teeth just before going to bed.  It obviously felt a little strange but did not keep me from falling asleep.

 

2015/07/07 (T) Field Day Photos

Leave a reply

We did not sleep well last night, were slow to get up this morning, and slower to get going.  A cold front was pushing in from the northwest with the promise of cooler temperatures and sunny, blue skies, but first we were in for a day of overcast conditions and rain, which started around 8:30 AM.  It was a perfect morning to sit quietly in the living room, reading, writing, and drinking our coffee but too warm to turn on the gas fireplace logs.

Yesterday Linda started researching RV parks in southern Florida for this coming winter and we spent some time this morning looking at them online.  There was one in particular, Riverside RV Resort and Campground, which caught our attention.  Located on the Peace River near Port Charlotte and Punta Gorda, it is a short distance southwest of Arcadia where the annual Buss’in rally is held.  We went to the rally two years ago and had a great time so we will go again this year if we decide to winter in Florida, which is our current inclination.

One of the reasons for us to winter in Florida, at least occasionally, is our many contacts there.  Our friends, Steve and Karen, bought a mobile home near Venice; our friends, Chuck and Barbara, bought a lot at Pelican Lake in Naples; our ham radio friends, Bruce and Linda, bought a house on 25 acres near Brooksville; our GLCC fiends, Ed and Janet, bought a place that I think is near Sarasota; our FMCA Freethinker friends, John and Marian, bought a place in Dunnellon; and our other FMCA Freethinker friends, Ed and Betty, bought a place in Bradenton.  In addition to all of those folks quite a few of our RV friends, like Pat and Vicki, spend the winter in Florida, and the state has a lot of things to see and do, including one of the best state park systems in the nation.

Linda left for her appointment with the dermatologist and I got to work at my desk.  I continued to deal with e-mails related to the SLAARC domain transfer and an ongoing conversation with BCM publisher Gary Hatt.  I got a Dropbox link to some Field Day photos from Steve (N8AR) a few days ago and downloaded them.  Last night I got a similar e-mail from Mike (KE8AGY) with a Google Drive link and today I got one from Jim (N8HAM) so I downloaded all of those photos.  I spent most of the rest of the day selecting and processing the photos I took and then processed all of the ones I got from other people.

I took a break to chat with Linda when she got back from her appointment.  I then removed the defective Morgan M-302N VHF/UHF Lightning Arrestor from the cable entry box and boxed it up to ship back to Morgan.  I took another short break for dinner, which was an excellent Farro and kale dish, and then worked until 8:30 PM when we had agreed to watch a movie.  This evening’s choice was The Imitation Game, a film about Alan Touring and the concepts he invented that allowed the British to build a machine that broke the coded messages generated by the German Enigma machine during WWII.  I spent another hour at my desk after the movie before going to bed and finishing this post.  Tomorrow morning I plan to finally upload some blog posts and then get back to work on the design of the custom desk for the bus.

 

2015/07/05 (N) Return to HFM

Leave a reply
Madeline helps Grandma Linda mix the batter for vegan blueberry pancakes.

Madeline helps Grandma Linda mix the batter for vegan blueberry pancakes.

The day started with Grandma Linda’s fabulous, made from scratch, blueberry vegan pancakes for breakfast, which Madeline helped make!  After breakfast we took Madeline to the Howell Farmers Market (HFM).  She had been to this market with us once before and it was a beautiful Michigan summer morning for a return visit.  On the drive over we discussed why it is that you cannot buy a farmer at a farmers market and you cannot buy a garage at a garage sale.  English can be a funny/strange language.

We walked the entire market, which is not really that big, and Linda bought some fresh strawberries.  A couple of the regular vendors were missing.  In particular we wanted to buy some more soap from Marjorie but she was not there.  Madeline enjoyed checking out the child and doll sized wooden furniture that one vendor had for sale.  We kept an eye out for someone selling jelly beans but did not see any so we stopped at the CVS on the way home and got a small bag of them.

We had just gotten home and I was unlocking the front door when Brendan and Shawna arrived.  We had a nice visit and they stayed for a light lunch.  By the end of lunch Madeline was showing signs of being ready for her nap so Brendan transferred the car seat and stroller from Linda’s car to their car, gathered up all of Madeline’s things, and loaded their car.  Madeline left with her parents at 12:30 PM and Linda laid down for a nap shortly thereafter.

I looked at the SLAARC WordPress website on my iPad to make sure it was working.  I checked most of the pages except for the Member Only Area, which requires a login, and they appeared to be OK.  I then went to my office to deal with things that needed to be dealt with from there.

Madeline tries on a child sized rocking chair at the Howell Farmers Market.

Madeline tries on a child sized rocking chair at the Howell Farmers Market.

My first task was to update the roster and financial records for our FMCA Freethinkers Associate Chapter.  I sent e-mails to new members, uploaded the updated roster to our Dropbox, and e-mailed everyone that they were available.  I had received the draft copy of the June 2015 issue of Bus Conversion Magazine on Friday.  I proofread part 3 of my 4-part article on the exterior renovation of our motorcoach and sent corrections to the editor.  I then settled in to edit blog posts.

I took a break for dinner.  Linda cooked Brussels sprouts and heated some vegan riblets.  The barbecue sauce on these riblets is very tasty.  We had vegan chocolate cupcakes for dessert and they were very tasty too.  I then went back to my office and continued editing blog posts.

I took a break just before 8 PM to join the South Lyon 2m Information Net using our new Yaesu FTM-400DR/DE RADIO but I did not hear anything except noise.  I left the radio on for a while and then turned it off.  I switched the coax to the Icom IC-7000 and turned it on but did not hear anything there either.  I turned the IC-7000 off, switched the coax back to the FTM-400, turned it back on, and went back to work at my desk.  Around 8:30 PM the squelch started opening and I heard very faint voices way down in the noise.  After listening carefully I was able to determine that it was Steve (N8AR) running the net but I could not understand most of what was being said.

It was the first time in a long time that I had tried to participate in the net and I was disappointed that the new installation of the antenna on the tower and coax cables to the radios in the basement was not working adequately.  They were working OK when I tested them with Mike (W8XH) so it could have been an unusual band condition but Steve was obviously getting in from farther to the west than our QTH.  I enjoy operating and am looking forward to finally having our larger tower up and some HF antennas in operation but for now I need to concentrate on getting the VHF/UHF stuff working reliably (correctly and consistently).

I exchanged some e-mails with Gary at BCM regarding the magazine and then continued editing blog posts.  I got through the end of June by 11 PM and quit for the night.

2015/07/03 (F) 4th Anniversary

Leave a reply

Several SLAARC members were gathering at 10:30 AM this morning to unload the Field Day equipment from Steve’s trailer and store it in the South Lyon water tower.  I was going to join them but decided last night to stay home and work on the design for the desk and HVAC chase covers for our motorcoach.  Having played ham radio for much of the last week and a half I needed to refocus my time and attention on the interior remodeling of our bus.  Besides, Brendan was bringing Madeline to our house sometime mid-to-late morning and I wanted to be home when they arrived.  Today was Brendan and Shawna’s 4th wedding anniversary and they asked Linda if we would take care of Madeline for a couple of nights so they could have some time together without the constant demands of child care.  Of course Linda said ‘yes.’

I had a call last night from XPO Delivery Services letting me know the new refrigerator for the bus would be delivered to Chuck Spera’s shop in Novi today between 6 and 8 PM.  That meant I would have to be at the shop by 5 PM just in case they arrived early and could be there past 8 PM if they arrived late.  At 7:45 AM this morning I got a call from the Lowe’s in Howell asking if XPO could deliver the refrigerator in about an hour.  Sure, why not; I was still in bed but about to get up anyway and having the refrigerator delivered early would actually open up my entire day.  I hurried the process along, had Linda get the receipt, grabbed my iPad, and headed for Chuck’s shop in Novi.  Linda was getting ready to go for a walk as I left.

One never knows what the traffic will be like on I-96 headed into the Detroit metro area from the northwest but on this Friday, at the start of a major holiday weekend, the traffic was very light and I was able to get to Novi in the minimum legal time.  Traffic headed westbound actually appeared to be heavier than the inbound traffic.  I stopped at the Tim Horton’s on Beck Road just north of Grand River Avenue and got coffee which I had not taken the time to make at home before I left.

I texted Chuck to let him know that the refrigerator was being delivered this morning.  He called me back to clarify where to have them set it.  This would be a great weekend to do the swap as all of the other businesses around his shop building will be closed for the holiday, making it easy to get our bus in and out.  But his daughter arrived last night from New York and will be visiting for a week so the refrigerator replacement will have to wait, probably until at least next weekend.

By 9:30 AM XPO had not arrived so I called Lowe’s in Howell and talked to Erica in scheduling.  She said she would call the driver and see what was going on.  I texted a status update to Linda and continued to wait.  By 10 AM there was still no truck and no call back from Erica.  At 10:20 I was dialing Lowe’s again when an Enterprise rental truck drove past the building headed east and a few minutes later went by headed west and pulled into a parking lot.  Moments later my phone rang.  It was the XPO truck driver.  I explained where the driveway was and flagged them in.  When I ordered the fridge I gave detailed special instructions on how to find the building but the driver did not bother reading them and did not bother calling me until he had failed to find the delivery location for the second time.

They backed the truck into the area in front of Chuck’s garage door, lowered the refrigerator down on their lift gate, slid a pair of lift straps under it, picked it up, and carried it into the shop.  I looked it over as best I could and then signed for it.  Only later did I notice a small dent towards the bottom of the door.  I had an automated call later asking if I was satisfied with the delivery and indicated ‘no’, noting the arrival delay and the small ding.  The message said I would hear back from someone within an hour but no one ever called.  We do not plan to make an issue of the ding as we will be lucky to get it into the bus and into its alcove with no further damage.  Still, it should have arrived in perfect condition and did not.

I called Linda to let her know the refrigerator had arrived and that I was getting ready to head home.  She said Brendan had just arrived with Madeline.  As I started to back out of my parking spot Chuck arrived so I spent about 30 minutes talking with him about the timing and approach of the refrigerator swap.  I will almost certainly take our bus to his garage on a weekend.  Only later did I find out that Brendan will not be available to help for the next two or three weekends.  Ugh.  Chuck called a friend (golf buddy) who has narrow pallets (24″) to see if he could get a 5’ long section.  With the long forks set close together on his forklift we can slide the pallet over the forks and have a much more secure platform form for raising and lowering refrigerators, probably laying on their backs.

Linda called back and asked me to stop on the way home for some toddler toothpaste and a toddler toothbrush.  I did not know they made such things but I found them at the CVS in Brighton.  Not long after I got home Linda had lunch on the table.  She heated some veggie nuggets and set them out along with baby carrots, grapes, pretzels, hummus, vegan deli slices, bread, lettuce, and onion.  We all had a good lunch with lots of variety.  Brendan got Madeline down for her nap at 1 PM and hung around long enough to make sure she was asleep.  I took a few minutes to show him the new Yaesu radio before he headed back to Ann Arbor.

I was very tired and took a nap on the living room sofa which is especially comfortable for this purpose, better actually than for sitting on.  Madeline slept until almost 4 PM.  When she woke up she wanted her mommy and daddy and was a little weepy but Grandma Linda got her quickly engaged in doing things.  Linda took her for a walk to see the chickens while I went downstairs to check e-mails.  I responded to ones having to do with the transfer of the SLAARC website and domain name registration from GoDaddy.com to QTH.com and made mental note of others.  When they got back from their walk Linda brought Madeline downstairs to see Grandpa Bruce at work in his office and ham radio shack.  We told her we would help her become an amateur radio operator when she was older.

Linda decided that baking a vegan chocolate cake would be an excellent activity to do with Madeline and give us a nice treat for later.  Madeline helped pour and stir ingredients.  She ended up with chocolate cake batter on her face and clothes but it was worth it as she got to lick one of the spoons.  (Without any animal products, especially raw eggs, vegan cake batter is perfectly safe to eat.)  Linda had previously found a small baking set for Madeline that included a small bunt cake pan.  Some of the batter went in there to make a little cake just for Madeline and the rest was used to make 11 cupcakes.

After the cupcakes were cooked and taken out of the oven to cool Linda made dinner.  We had mock chicken strips (vegan), fresh sautéed green beans, vegan refried beans, and fresh berries leftover from earlier.  When the cakes were cool enough Linda got out the powdered sugar and sifter and we dusted them.  Madeline enjoyed the decorating but somehow ended up with powdered sugar in her hair, on her dress, and all over her face.  I took pictures and then Linda cleaned her up while I cleaned the floor.

After dinner and dessert we played and read a bit.  Linda had gotten three Sesame Street Workshop DVDs from the Howell Public Library so we all climbed up into the bed in our bedroom and watched one of them.  We played along with the various activities and games and encouraged Madeline to do the same.  The program ended at 8 PM which is Madeline’s bedtime.  Linda helped her in the bathroom, got her into her pajamas, and helped her brush her teeth.  She laid down without a fuss and drifted off to sleep. We stayed up until the last chime of the grandfather clock at 9:45 PM and then turned in for the night.  We are always satisfyingly tired after a full day of Madeline.

 

2015/07/02 (R) 100,000 Radios

Leave a reply

We were tired and did not get up until almost 8 AM.  Linda prepared a tofu scramble for breakfast, as we were almost out of her homemade granola, and served it with some cinnamon raisin toast and fresh grapefruit.  It’s the closest thing we eat to scrambled eggs and she serves it as an occasional change of pace from our standard granola breakfast.

I had my annual appointment with my dermatologist this morning at 11 AM.  I needed to pick up a cable from Scott (AC8IL) at Adams Electronics, which was on my way to the Henry Ford Health System (HFHS) clinic, so I left the house a little after 9:30 AM.  The drive was fine initially and I had a nice QSO (chat) with Steve (N8AR) on the South Lyon 2m repeater.  As I was approaching Wixom Road, however, all lanes of eastbound I-96 were stopped.  I was able to exit at Wixom Road and headed north a short distance to West Road which I took east over to Beck Road where Scotty’s business is located a little north of West Road.  I had a brief chat with Scott about the antennas on my tower before I left.

Two miles north of Scott’s shop I turned east on Maple Road (15 Mile Road).  The HFHS has many clinics around the greater Metro Detroit area and my dermatologist is located at the intersection of Maple and Farmington Roads in West Bloomfield.  That should have been an easy trip but there was construction on Maple Road that had the road down to one lane with flaggers.  There were signs advising motorists to seek other routes but I did not heed the warning.  I patiently worked my way through and arrived for my appointment about seven minutes ahead of time.  Good thing I left as early as I did.

My exam was fairly routine and Dr. Nydorf wrote out a prescription for Doxycycline.  I will try taking it (again) three times a week and see if it helps.  I headed straight for home after my appointment but took a different route.  Once I was back at the house Linda went for a walk.  While she was walking I removed the license plate from her car, took the protective (anti-theft) cover off, and cleaned everything.  When it was dry I put the new registration sticker in the corner, reassembled the cover, and installed the plate back onto the car.  I then started working with the various pieces of the new Yaesu FTM-400DR/DE mobile radio.  When she got back from her walk she heated up a couple of tofu hotdogs for lunch.  These are such simple fare but so tasty (with mustard, onions, and relish) and so appropriate for a summertime lunch.  They are also a really easy lunch to get on the table.

After lunch Linda took her car to the Howell library to get some books and children’s DVDs and then stop at the Meijer’s supermarket to pick up a few grocery items for Madeline’s visit this weekend.  While she was running errands I assembled our new Diamond X-300NA antenna.  Once it was assembled it was over 10 feet long so I stored it by mounting it to the side of the tower.  I put it up as high as I could reach from the ground to get the three counterpoise (elevated ground plane) rods above eye level.  Moving it to the top of the tower as a replacement for the Diamond X-50NA will have to wait until next week or later.  The exact timing will depend on the weather, Mike’s (W8XH) availability, and whether I have acquired appropriate standoffs by then for the X-300 antenna and/or the cellular booster omnidirectional antenna.

With the antenna taken care of (for now) I disconnected the coaxial cable for the X-50 from the radio side of the lightning arrestor and positioned it so I could pull it back into the sump pump room.  From there I fed it into the ham shack, disconnected it from the radio, and coiled it up.  I uncoiled the new 20′ LMR-400 cable with the N-male connector end positioned so I could feed it through the corner of the ceiling in the ham shack (by the ground wire) and into the sump pump room.  From there I fed it through one of the 2″ conduits into the cable entry box.  Back outside I shaped the cable (LMR-400 cable is double shielded and stiff) and connected it to the radio side of the Morgan VHF/UHF lightning arrestor and closed the lid on the box.

Back in the ham shack I attached the PL-259 connector to the SO-239 socket on the back of the Icom IC-7000 GoBox.  I could have gotten away with a 16′ cable but the 20′ length gives me more flexibility with respect to equipment placement.  I turned on the IC-7000 but did not hear anyone on either the South Lyon 2m or the Novi 70cm repeaters so I turned it off.

I disconnected Mike’s Icom IC-2820H and set it aside to make space for the new Yaesu FTM-400DR/DE dual band mobile transceiver.  I moved the new coax to the new radio, powered it up, spent a few minutes configuring some basic things, and then listened to the South Lyon and Novi repeaters.  I tried calling them but was not triggering them so I knew the PL Tone was not set correctly.  I called Mike for assistance and left him a voice message.

Linda was back by this time so she came down to see the new radio.  We then went out to the bus to make our final decisions about upholstery fabric and window shade materials.  In the end we chose the Lambright Notion Linen fabric for all four chairs and the MCD B50 material for the dark out shades.  We brought all the samples back in the house and I e-mailed our choices to Josh at Coach Supply Direct.

I had an e-mail from Scott Neader (KA9FOX) at QTH.com requesting an admin login for the SLAARC WordPress website so I set that up and e-mailed him back.  I had the new radio on and was listening to a conversation on the Novi repeater.  It had just concluded when Mike returned my call.  He walked me through how to set up the PL Tone and Squelch Tone for both of the repeaters on the FTM-400.  We were then able to verify that the radio was working on both bands.

For dinner Linda made a salad and pan-grilled tofu with caramelized onions and barbecue sauce which she served open-faced on hamburger buns.  We had watermelon for dessert, which we have been doing a lot this summer.  I did not care for watermelon as a child but it has become a favorite summertime treat.  I had dropped a small lock washer while mounting the new antenna to the tower earlier so I went to Lowe’s to get a replacement and some spares.  On the drive there I got a call from XPO Delivery Service letting me know that the new refrigerator for the bus would be delivered to Chuck’s shop in Novi tomorrow between 6 and 8 PM.

At Lowe’s I picked up some 6mm x 1.0 Nylok nuts in addition to the lock washers.  I also got some grass seed patching mix, a few more bags of decorative broken brick pieces, and a hummingbird feeder with a red reservoir so Linda can use sugar water without red food coloring.  When I got home the odometer on my car read 100000 so I took a picture of it with my phone.  I then spread the patching mix over the bare dirt I had used to fill a hole and troughs left by the installation of the natural gas line to our house last September.  The rest of the evening Linda read and I worked on completing drafts of blog posts.

 

 

2015/06/29 (M) Website On The Air

Leave a reply

Linda was up at 5:55 AM this morning and left for the bakery at 6:15.  Experience has shown that this is usually early enough to get ahead of the morning rush hour traffic inbound to the Detroit metro area from the northwest.

I got up about an hour later, had granola for breakfast, and enjoyed my morning coffee (Sweet Seattle Dreams half-caff blend from Teeko’s) and then made a run to Lowe’s to purchase a couple of copper ground lugs and 5 feet of #10 green ground wire.  Back home I tried to use one of the ground lugs to terminate the ground wire from the cable entry box (CEB) to the 36″ ground bar on the wall behind the ham radio desks but it’s shape prevented the wing nut from going onto the stud.

I planned to use the other lug to attach one end of the #10 wire to the ground bar and put a male spade lug on the other end to mate with the connector on the Go Box ground pigtail, but that clearly was not going to work.  I dressed the ground wire and (temporary) coax in the ham shack and put the ceiling tile back in place.  I then started cleaning up the living room and small bedroom per Linda’s request before she left this morning.  Some of our (my) projects have a way of expanding throughout the whole house.  I had hoped to also pick up the coax cables spread out in the recreation room, and at least start to straighten up the ham shack/office, putting materials away and moving tools to the garage.

At 10 AM I made a few phone calls.  The first was to Rick Short at ISRI USA regarding the 6860 bus driver’s seat and a possible visit tomorrow morning.  I got his voice mail (again) and never got a return call (again) so I gave up on getting any assistance from him or from ISRI USA.  I called Linda to make sure she did not have any commitments on Wednesday and then called Josh at Coach Supply Direct to set up a visit to his shop for Wednesday late morning.  Linda and I plan to finalize our Flexsteel furniture order and give Josh the deposit during that visit.  Next I called Scott Adams, AC8IL, at Adams Electronics and ordered a 20 foot length of LMR-400 with an N-male connector on one end and a PL-259 connector on the other end.  Scotty and I also chatted briefly about tower bases.

I e-mailed Scott Neader at QST.com regarding the transfer of the SLAARC domain name and website from GoDaddy to QST.com and got a reply back right away with an outline of the steps I needed to follow.  First on the list was creating an account for our ham radio club through his billing system.  I took care of that and e-mailed him back.

Keith Kish, from Kish Lawn, care showed up around 11 AM to cut the grass.  When he was done I headed back to Lowe’s to look for an alternate ground clamp and pulley support for the tower but did not find anything suitable.  So as not to have it be a wasted trip I bought three more bags of broken brick pieces to use around the tower base and cable entry box.

I spent some time looking at the Yaesu FTM-400DR/DE on several different ham radio equipment vendor websites.  Yaesu is offering a $100 rebate on this 2m/440 mobile radio through tomorrow.  All of the distributors are selling it for the same price, $599.95 and the rebate brings it down to $499.95, so if I buy one it will come down to who has them in stock and is offering free shipping.

Linda got home from the bakery around 3 PM, earlier than I expected and nice for her.  She went for a walk while I continued to fuss with ham radio and website stuff.

For dinner Linda made a white beans and mustard greens dish.  We eat a lot of lettuce, kale, and spinach, both raw and cooked into dishes, but only occasionally have collard greens or mustard greens.  Mustard greens have a very strong, bitter flavor and I liked them more than Linda did.  I think they are an acquired taste and may be more suitable as an accent ingredient rather than a main one.

After dinner I checked my e-mail and had a reply from Scott at QTH.com.  The QTH SLAARC account invoice was ready so I paid it using a personal credit card.  I then moved the coax from our Icom IC-7000 to Mike’s Icom IC-2820H and turned it on.  Mike was on the South Lyon repeater discussing the Field Day event with Steve (N8AR) and Bruce (W8RA).  Paul (N8BHT) was able to join the conversation but I was not successful breaking in so I just listened.  It was an indication that my power into the repeater was probably still marginal but a good reminder that ham radio conversations are very public.

When they were done I called for Mike and he came back.  We had a good QSO (chat) about the Yaesu FTM-400.  Jim (N8KUE) joined in for a while.  After Jim dropped off we tested my ability to transmit to, and receive from, both the South Lyon 2m and Novi 70cm repeaters.  The added power of the IC-2820H over my IC-7000 (50W vs 35W in the 70cm band) combined with the lower signal loss of the better coax made just enough difference that I could hold the Novi repeater when transmitting although my signal was still on top of a lot of noise coming back out of the repeater.

Linda wanted to watch an episode of Scorpion, followed by NCIS Los Angeles, after which I caught an episode of Two and a Half Men and then turned off the TV.  I will have to make a decision about the Yaesu FTM-400 in the morning.

 

2015/06/28 (N) Field Day Teardown

Leave a reply

I was up at 7:15 AM and showered.  The rain finally cleared out leaving blue skies but with scattered white clouds still blowing across the region on brisk winds out of the NNE.  Linda was up by 8 and got the fresh fruit ready for our breakfast cereal while I made the coffee, which we enjoyed in the living room to warmth of the natural gas fireplace.  I did not expect to be using the fireplace this time of year but we have the furnace turned off, and are still getting overnight lows in the 50’s, so the fireplace is an effective and charming way to alleviate the slight morning chill in the front of the house.

In spite of the weather the food tent stayed up and open for business.

In spite of the weather the food tent stayed up and open for business.

I finished up the draft of my blog post for yesterday and started on this one while I drank my coffee.  By 9:45 AM I was ready to install the #6 green coated ground wire I bought last night.  I also decided to switch out the coax from the cable entry box (CEB) to the ham shack.  Linda had made a grocery list and left to do the shopping.

Outside I opened the CEB and disconnected the current VHF/UHF coax and let it slide back into the sump pump room (SPR).  Inside I removed the suspended ceiling tile in the northeast corner of the ham shack and routed the ground wire over the wall into the SPR.  I fed it through an existing cable tie on the bottom of one of the floor joists and through the outer wall into the CEB.  I had an unused copper ground lug and used it to connect the ground wire to the lower right mounting stud for the CEB copper backplane.

Back inside I uncoiled a length of 50 ohm coax that I borrowed from Mike (W8XH) and followed the same path as the ground wire.  Outside at the CEB I installed an N-male/SO-239(F) adapter onto the PL-259 connector on the end of the coax and attached it to the N-female socket on the lightning arrestor.  I was finished working in the CEB, closed the cover, and went back to the basement.

I decided to install the 36″ copper ground bar on the wall behind the ham shack desks just below the 120 VAC outlet strip, which required me to move the desks away from the wall.  I attached the end of the ground wire to one of the studs by spreading the strands and placing them under a washer and wing nut.  I need to get another copper lug to do this right.

Steve (N8AR) operating the 6m opening from the radio in his car.

Steve (N8AR) operating the 6m opening from the radio in his car.

I had a five foot length of braided tinned copper strap and used it to connect the ground terminal on the Go Box to the ground bar.  I spread the braid apart to make a small hole near each end, slipped the holes over the studs, and clamped them under washers.  This was a temporary arrangement for testing purposes.  I need to configure a length of #10 copper wire with a ring terminal on one end and a make spade connector on the other but did want to take the time to do that today.

With everything hooked up I called Mike (W8XH) to see if he was available for a quick radio test.  He was still at home and about to leave for the SLAARC Field Day site but gladly delayed his departure long enough to help me test the new configuration.  The result was a better send and receive signal on 2m, both direct and through the South Lyon K8VJ repeater, with an S3 received signal strength with the pre-amplifier turned on.  The direct signal was also a little better on the 440 MHz band but my received signal from the Novi repeater was still weak and noisy and my transmit signal was still not strong enough carry the repeater.

I had planned to leave around 11AM for the SLAARC Field Day site but wanted some lunch before I left.  I had just made a sandwich and was gathering up my equipment when Linda got back from her grocery shopping.  By the time I left it was past noon.

I was interested in our ham radio club’s participation in this year’s ARRL Field Day event but neither Linda nor I had had any need or desire to operate radios.  I worked all day Friday on the setup of the towers and antennas and helped a bit last night with the emergency teardown of the VHF/GOTA canopy.  The 24-hour Field Day operating window closed at 2 PM today but some of the teardown began before that time and I wanted to be there to help.

SLAARC members enjoying lunch outdoors at the Field Day site.

SLAARC members enjoying lunch outdoors at the Field Day site.

Some teardown was already underway when I arrived at the SLAARC Field Day site and lunch was also just being served, so everyone took a break to get something to eat except Steve (N8AR).  He was sitting in his car making contracts on the six meter (6m) band using the mobile radio in his car.  He had connected it to the 6m beam antenna on top of the big tower.  The 6m band is known as “the magic band” because it will suddenly “open” and allow very clear communication over great distances and then just as suddenly close.  It had apparently opened up this morning from the Mississippi River to the East Coast and south into the Caribbean.  One of our members made a contact with someone in the Dominican Republic.  While I was watching and listening I heard calls coming in from South Dakota and New Mexico.

This is the fourth year that Marianne Roney, the wife of one of club member Ed Roney (KD8OSM), has taken care of the Field Day meals, which include lunch and dinner on Saturday and breakfast and lunch on Sunday.  The meals are $5 per person per meal, which is a bargain for the variety and quantity of things she prepares and provides, except that there is typically very little we can eat.  She would make special provisions for us if we asked (she did the first year) but it is extra work for her and we are still left with not being able to eat most of what is available, so we do not purchase meals.

Operating stations are often staffed by two people, one operating the radio (left) and the other logging the contacts (right).

Operating stations are often staffed by two people, one operating the radio (left) and the other logging the contacts (right).

As the operating event was drawing to a close the computer in the 40m tent shut down.  The computers are not used to operate the radios, but are connected to them and are used to log the contacts using the N1MM Logger+ program.  The program reads key information about frequency and mode from the radio so all the logger has to capture are call sign, operating category, and section.  (Club member Larry, K8UT, is a member of the N1MM Logger development team.)  Every radio was paired with a laptop computer running this program, and the computers were all linked together via Wi-Fi.  As a result, the operators/loggers at each station could see all of the contacts that were being made regardless of which station made the contact and each computer contained a complete list of contacts.  The program also flags “dupes” (duplicate contacts).  In a contest situation this allows the operator to see that they have already worked that station on a particular band and mode and not spend time working it again on the same band and mode as duplicate contacts do not contribute to the contest score.

Just as it had started 24 hours earlier, at 2 PM it was all over without any fanfare.  The radios and computers were shut down and then the AC power generator was shut down.  Cords were unplugged, coiled, and staged near the vehicles they would eventually be loaded into.  Radios and computers were carefully disconnected, boxed (in some cases) and carried to the vehicles of their respective owners.  Tarps were pulled from the tents and folded and then the tents were collapsed and folded.  Four of use took down the 40m crossed dipole (inverted V) antenna and then took down the small support tower and disassembled it.  A larger crew eventually lowered the bigger tower, which required a winch, until it was resting in a step ladder.  This was necessary because of the two beam antennas at the top of the tower.  They removed the 6m and then the 20m beam antennas and then lowered the tower to the ground.  Part of the crew disassembled and packed the two beam antennas while the rest of them took the tower apart

A path map from Eric's (K8ERS) cell phone of the early morning 6m band opening.

A path map from Eric’s (K8ERS) cell phone of the early morning 6m band opening.

We were essentially done with the teardown by 4 PM.  The teardown is always much faster than the setup and yet it was very relaxed and went very smoothly.  In spite of weather challenges all day Saturday and overnight into Sunday, and the disappointment of not having all of our stations on the air due to losing tents to the wind, we had a beautiful last day for the event and teardown.  Blue skies, white puffy clouds, cool temperatures, lighter breezes, and low humidity combined with a sufficient number of competent, helping hands, made for easier work for everyone.  The group stood around reflecting on the event and everyone was in a good mode, a sure sign that the 2015 ARRL Field Day had been a success for the South Lyon Area Amateur Radio Club.

I was the last one to pull out, right behind Steve who was towing a fully loaded enclosed trailer with a lot of the club’s equipment in it and on it.  We chatted via the South Lyon repeater on the drive home, our last radio work for the day.  I was home by 5 PM and just relaxed until dinnertime, tired from the sun, fresh air, and work.  For dinner Linda made a potato and spinach curry dish that she found in her Indian cookbook.  She also steamed some asparagus that she bought at the Howell Farmers Market this morning.  We had a quiet evening of reading, writing, and games before turning in at 10 PM.

 

 

2015/06/27 (S) ARRL Field Day

Leave a reply

At 5 AM I was vaguely aware of the sound of rain.  The cats were chasing each other through the house so I got up to make sure nothing was amiss, such as another mouse.  They were just having a bout of morning friskiness.  I added a little food up to their bowls, which drew their attention, and went back to bed.

My Amateur Radio vanity license plate. There were a LOT of these in the parking lot at the SLAARC Field Day site.

My Amateur Radio vanity license plate. There were a LOT of these in the parking lot at the SLAARC Field Day site.

I finally woke up and got up about 8:15 AM and got dressed in a suitable manner for today’s American Radio Relay League (ARRL) Field Day event.  The temperature was in the mid-50s, overcast and raining with blustery winds; not exactly the nice summer day we were all hoping for.  Some of the members of the South Lyon Area Amateur Radio Club (SLAARC) were gathering for breakfast at the usual place (Senate Coney Island) at the usual time (8 AM) but we obviously did not join them today.

I went to my office to retrieve my Sony DSLR and decided to turn on our Icom IC-7000 ham radio.  I had it tuned to the SLAARC (K8VJ) repeater in South Lyon when Keith, KD8YYJ, announced his presence.  He was driving from the west side of Howell to Wixom and seeing what repeaters he could hit.  We chatted for 10 to 15 minutes and I invited him to stop by the SLAARC Field Day site at the South Lyon Township James F. Atchison Memorial Park.

I worked all day yesterday as part of the SLAARC Field Day setup crew.  There was more setup to do starting at 9 AM this morning but the setup mostly involved radios, computers, Wi-Fi networking, and power.  I was not in any humor to rush off into the clammy weather conditions, and Linda was up by this point, so we had breakfast.  She found some Silk brand ‘yogurt’ at Meijer’s last week so we had that.  It was OK.  It is a creamy style yogurt, which is not my preference, but it was tasty enough.  Bananas, cinnamon raisin bread, and juice rounded out the meal.  Linda even made the coffee.  I turned on the natural gas fireplace to ward off the chill in the living room where we lingered and enjoyed our morning brew.

The SLAARC Field Day operating stations use wirelessly networked computers (left) running N1MM Logger+ to record the contacts that are made. HF transceiver to the right.

The SLAARC Field Day operating stations use wirelessly networked computers (left) running N1MM Logger+ to record the contacts that are made. HF transceiver to the right.

I finally left for the Field Day site around 11 AM.  The operating event started at 2 PM but the first of four meals was lunch today at noon and I wanted to capture photos of the rest of the setup and the lunch event.  It was raining lightly when I arrived and continued to rain until I left at 2:15 PM.  In between arrival and departure I took some photos and helped out a little bit, but there were plenty of people there taking care of what needed to be done.

Mike (W8XH) brought his Icom IC-2820H dual band mobile radio and several lengths of 50 ohm coax and we transferred those to my car.  He then walked me through the various menus and functions his new Yaesu FTM-400DR/DE radio, a dual band (VHF/UHF) 50 Watt rig with digital voice capability and a color touch screen display.  A group of SLAARC members recently purchased a Yaesu DR-1X repeater that works with the new Yaesu digital voice and data modes in addition to the traditional FM mode and are testing it as a replacement for the current, and very old, K8VJ repeater.

Mike’s IC-2820H is available for $350 but the FTM-400DR has a $100 rebate through the end of June, bringing the price down to $500.  As much as I would like to have a VHF/UHF radio in my car I am looking at one of these radios to install in the cockpit of the bus so we can use it going down the road.  The long-term plan is to put the Icom IC-7000 HF/VHF/UHF radio in our towed vehicle and get the Hi-Q 80-6 antenna mounted and operational in addition to the Diamond SG-7900 VHF/UHF antenna that is already on the Honda Element.

For base station use I would like to get an Elecraft K3s or Flex SDR rig.  The K3s has become the rig of choice among the members of the SLAARC who are serious about working HF and contesting.  Either of those are radios that could be fairly easily moved from the house to the bus when we travel.  Antenna options in the bus could include running coax to the Hi-Q on the toad and/or a “flagpole” HF vertical that is mounted using the towbar receiver or a base stand that goes under one of the tires.  An antenna switch would allow the use of the VHF/UHF antenna that was already installed for the cockpit radio.  All of these “base station” options would obviously be for stationary use only.

[Photo 3 – HC]

The ARRL FIeld Day event showcases the ability of amateur radio operators to set up equipment in the field on short notice and keep it on the air for 24 hours, no matter what. The weather turned bad for the event. The portable generator is under the tent in the right foreground.

The ARRL FIeld Day event showcases the ability of amateur radio operators to set up equipment in the field on short notice and keep it on the air for 24 hours, no matter what. The weather turned bad for the event. The portable generator is under the tent in the right foreground.

I uncoiled the coax cables that Mike lent me to see how long they were.  There was a 5 foot piece that was too short for what I needed, and a piece that was approximately 40 feet, which was longer than I needed.  The third piece was at least as long as the 40 footer.  I “tagged” his coax with small white cable ties so I could identify them later and return them to him.

I did not want to mess around switching coax cables in the rain so I unboxed Mike’s Icom 2820 and got it set up to use with my existing antenna and transmission lines.  I spent a little time with the manual and then powered it up.  It was already configured from when Mike used it in his ham shack so I did not need to do any setup to use it.  I monitored both the South Lyon 2m and Novi 440 MHz repeaters and was able to “hear” both of them, although the South Lyon signal was much better (stronger, quieter, clearer) than the Novi.  A couple of SLAARC members were on the South Lyon repeater taking care of Field Day business.  I waited a suitable amount of time after they were done and called for Mike (W8XH) and he came back right away.

We repeated the testing we had done last night.  The performance with the 2m South Lyon repeater seemed to be much better but the performance on the 70cm Novi repeater was the same or worse with a fading component to the noise.  I think we were on the air 15 to 20 minutes.  Based on the test results from last night and this afternoon I think I have two separate issues that are probably interacting; the IC-7000 needs to be grounded and the 25 feet of coax from the cable entry box (CEB) to the radio (Go Box) needs to be shorter and much higher quality.  I need to install the ground bar on the wall behind the ham radio desks and then purchase a suitable length of ground wire and run it from the CEB to the copper ground bar.  I will also need to get a 15 foot length of 50 ohm LMR-400 coax from Scott (AC8IL) with an N-male connector on one end and a PL-259 connector on the other end.

Linda prepared our dinner at 5 PM.  She made corn-on-the-cob and “cowgirl steaks,” a new (to us) vegetable protein product she found at Meijer’s.  After dinner we drove back to the SLAARC Field Day site to socialize with club members at dinnertime.  The weather at our house was still rainy with light-to-moderate winds and occasional stronger gusts.  We arrived at the Field Day site to find a flurry of activity and strong, steady winds out of the north with continued sporadic rain.

Jim (KC8WMW) stays dry as he works the GOTA (Get On The Air) station in one of the tents.

Jim (KC8WMW) stays dry as he works the GOTA (Get On The Air) station in one of the tents.

The small red tent that was originally supposed to be the VHF tent was nowhere to be seen and at least eight people were engaged in trying to control and fold up the large canopy that the club purchased yesterday at Costco to serve as the combined VHF and GOTA tent.  We quickly learned that the small tent, which was not being used, had collapsed and the large tent, which was unoccupied but full of radios and computers, had come unstaked and blown over in the wind.  Those who were not helping with the equipment canopy were gathered in the food canopy.  I pitched in on the equipment canopy rescue and Linda took the camera and joined the folks in the food tent.

After gathering up all of the pieces of the canopy and getting them back in the trailer some of the team added extra ropes and stakes to the windward end of the food canopy and both the 20m and 40m tents.  Another part of the team, including me, got Marty’s (KB8JIU) satellite tracking equipment out of the screen room, which had been draped with solid plastic tarps to keep the rain out, and then took the room down, disassembled the legs, folded it up, and stuffed it in the trailer.  The red tent was stuffed under a picnic table that was in the screen room so I grabbed that and put it in the trailer.  The support pole for one end of our off-center-fed dipoles was bending over to the south more than we liked.  Steve, N8AR, tied a rope around the existing rope, which was inline with the antenna and being used to keep it taught.  He slid the second rope up the first one as far as he could get it to go and then pulled it out to the northwest (the antenna was oriented east-west with the tension rope running east off of the east end).  He pulled it out until the support pole was reasonably vertical and I staked it down.

The winds really howled out of the north driving the rain before them. This shelter (from Costco) did not survive along with another tent and a screen room.

The winds really howled out of the north driving the rain before them. This shelter (from Costco) did not survive along with another tent and a screen room.

So the bad news was that some of our Field Day setup had not survived the weather which had not even reached severe conditions.  The good news was that our generator was still producing power, all of our towers and antennas were intact and functional, we had our two key stations on the air, and our food canopy was full of people and hot food.  Not the Field Day everyone had hoped for, but a great opportunity for teamwork and camaraderie and a learning experience to be sure, even if it was not the kind of lesson we wanted to learn.

We left around 7:30 PM and went to the New Hudson Lowe’s, which was very close to our Field Day site, where I bought 18 feet of AWG 6 stranded copper wire with a green sheath.  As soon as the weather improves I plan to run this from the CEB to the ham shack and use it to connect the ground bar in the shack to the copper backplane (ground plane) in the CEB.  I will then connect the ground on our Go Box (Icom IC-7000) to the ground bar and see if it helps with my noise issue.

Back at the house Linda wanted to watch an episode of NCIS Los Angeles, which we can now do thanks to our new OTA TV antenna.  We then watched an episode of Christina Cooks, Christina Perillo’s vegan cooking show from a decade ago.  These are still relevant and useful episodes and we especially enjoy them having seen and met her and her husband Robert on our two Taste of Health Holistic Holiday at Sea vegan cruises.  Linda read and I wrote for a while before lights out and off to sleep.

 

2015/06/26 (F) Field Day Setup

Leave a reply

I was up at 7 AM and ready to leave for breakfast with the other SLAARC members who would be setting up our temporary field site for the ARRL Field Day event.  I called the SLAARC repeater and Steve (N8AR) came back and wanted to know if I had the site use permit from the township?  No, I did not.  Paul, N8BHT, got on the air and said he gave it to Linda so I went back home.  Linda was up but had no recollection of receiving it.  We looked through the materials she got from Paul but could not find it.  I left again for breakfast but after more radio QSO went back a second time to retrieve all of the records and bring them with me to the field day site.  (Our best guess is that he gave the permits to the other Linda (NF8C) who is the club secretary.

SLAARC's Field Day setup begins in earnest when Steve's equipment trailer arrives.

SLAARC’s Field Day setup begins in earnest when Steve’s equipment trailer arrives.

By this time it was too late to make it to breakfast so I stopped for coffee and fueled my car.  Mike (W8XH) also did not go to breakfast with the group in South Lyon so we were the first to arrive at the site.  Another 10 guys showed up shortly thereafter.  John’s Sanitation then arrived and dropped off our rented porta-potty.

We had 12 people for most of the day and 14 total who were there for at least part of the day.  It was a good group and just the right size for the task.  We worked steadily from 9 AM until almost 5 PM except for an early afternoon lunch break.  By the end of the day we had erected two towers and set up six antennas (20m beam and 6m beam co-located on the taller tower, two off-center fed dipoles from the taller tower, a 40m crossed dipole from the shorter tower, and a 40m 1/4 wave vertical with four elevated counterpoise wires).  We also put up three radio tents, a screen room, and the big food tent.

Larry (K8UT) holds the 6m beam while Steve (N8AR) and others attach the 20m beam to the mast of the taller tower.

Larry (K8UT) holds the 6m beam while Steve (N8AR) and others attach the 20m beam to the mast of the taller tower.

The weather was cloudy and dull and not the best for taking photographs but I took pictures anyway.  I had to be deliberate in my shot selections, however, as both of my memory cards were almost full.  All of the work that needed to be done today was finished by 4:30 PM and most of us took off.  Our Field Day chairman, Paul (KD8SNZ), and a new member, Ron, setup their tents as they would be spending the night and keeping an eye on the site.  Steve (N8AR) and Eric (K8ERS) stayed a bit longer to test the antennas using the mobile radio in Steve’s SUV.

Back home I took a nap for an hour before dinner.  Linda grilled Portobello mushrooms and corn on the cob and cut up some fresh strawberries and cantaloupe.  After dinner I went to my office and transferred all of our recent photographs from the Sony alpha 100 DSLR to my computer and then to our older NAS device which we had with us this past winter.  I then started backing up all of the photographs we had taken since December 2014 from the old NAS unit to the new one.  This involved a significant number of images, a lot of gigabytes of data, and took a bit of time.

Rather than sit around waiting for file transfers to finish I decided to turn on the Icom IC-7000 ham radio and see if I could figure out why I could not hear the Novi 440 repeater on Wednesday when we tested the antenna and coax installation.  I checked the Nifty guide for the Icom IC-7000 and, as Mike had suspected, I did not have the Tone Squelch frequency set correctly for the Novi repeater.  I changed the mode on the 440 MHz band from ‘Tone’ to ‘TSQL’ and then caIled Mike (W8XH) on the phone to see if he could help me do a radio check.  We spent about an hour going back and forth between the Novi and South Lyon repeaters.

With the correct settings I was able to work both repeaters although I had a lot of background noise (static).  I played with the noise reduction (NR) and pre-amplifier functions and both seemed to help.  Mike tried various combinations of power and simplex operation and we determined that the basic problem seemed to be a weak signal in both directions.  I am still suspicious of the fact that I do not have the Go Box grounded as I vaguely recall from three years ago having noise problems with this setup until I grounded the box, which is tied to the radio ground.

Field Day is an "all hands on deck (antenna)" event for our SLAARC group.

Field Day is an “all hands on deck (antenna)” event for our SLAARC group.

Mike was suspicious of the coax I used to go from the lightning arrestor to the radio but looked up the specifications on my Diamond X-50N antenna and suggested that an antenna with more gain might be in order.  We also discussed the location where I placed the antenna on the tower.  Although most of the antenna is above the tower it is on the northwest leg.  The two repeaters lie to the southeast so the tower may be ‘blocking’ some of the signal although that does not seem likely to me.  Of more concern to me is that I mounted the base of the antenna so that two of the three counterpoise (ground plane) rods are even with, and parallel to, two of the three topmost crossbars.  If anything is being blocked it is likely those as the crossbars are between the rods and the repeater locations.

Ed (KD8OSM) jumped in briefly to let us know that I also had a ‘hum’ that sounded like the 60 Hz power line frequency only higher pitched.  I have a small fan installed in the back of the Go Box so I hummed the same pitch as it was producing into the microphone and both Ed and Mike confirmed that this was the tone they were hearing.  The fan is audible, but not that loud, and was two feet behind the microphone so I would be surprised if it was picking up the fan noise.  It is possible that the fan is inducing the hum electrically, but I believe it is a DC fan, so that seems unlikely.  I do not have an AC line filter installed on the fan, or anywhere in the box, so that may be a next step.

The larger of the two towers is up and secured. It has a 6m beam antenna on top of 20m beam antenna on a common mast with a rotator. We also attached one end of an off-center-fed dipole to this tower.

At the SLAARC Field Day site atop the Lyon Township Atchison Memorial Park the larger of the two towers is up and secured. It has a 6m beam antenna on top of 20m beam antenna on a common mast with a rotator. We also attached one end of an off-center-fed dipole to this tower.  Tents are being erected to house the various operating stations.  The weather was overcast and forecast to get much worse before Field Day as over on Sunday.

Mike and I wrapped up our QSO and I shut the radio off.  I checked my e-mail and saw that the May 2015 issue of Bus Conversion Magazine was available.  I logged in to the website and downloaded both the standard and high definition versions of the April and May digital editions.  By the time I got to bed it was well after 11PM.  I finished up yesterday’s blog post draft and outlined as much of today’s post as I could before I lost the sequence and details of the day’s events.

 

2014/09/07 (N) Findlay Hamfest

Leave a reply

I set alarms on my phone and iPad last night to make sure I got up at 5:00 AM.  My natural tendency is to stay up a little later each night, something I am now able to do as I do not usually have to get up by any certain time in the morning.  Usually.  Today, however, was the annual Hamfest put on by the Findlay, Ohio Amateur Radio Club and I needed to be at Mike’s (W8XH) QTH in time for a 6 AM departure.  We picked up Steve (N8AR) at the Park-n-Ride lot at Lee Road and US-23 around 6:15 AM and drove non-stop to Findlay, Ohio, arriving at the county fairground at 8:15 AM.  We had a good chat on the way down, which is as much of a reason for going as the bargain hunting once we got there.  I have included a couple of photos in this post.  For more photos, visit:

http://wp36test1.slaarc.com/gallery-2/hamfests/2014-09-findlay/

We each paid our $7 admission fee and got our ticket with a tear-off stub for the hourly and grand prize drawings.  We got parked and set our Kenwood TH-F6 handheld radios to 146.475 MHz (simplex).  We filled out our raffle ticket stubs, dropped them off, and started working our way up and down the rows of outside tables.  The outside sales area was essentially a flea market, sometimes referred to as “trunk sales” because people back their cars up to the road and sell stuff from their trunks.  The spots are cheaper to rent for the day, but you take a chance that the weather will be nice.

Outside vendors (trunk sales) at the Findaly ARC Hamfest in Findlay, OH.

Outside vendors (trunk sales) at the Findaly ARC Hamfest in Findlay, OH.

We worked the flea market first while the temperatures were cool and the sun wasn’t overhead but also because almost everything offered for sale was used equipment at negotiable prices.  These are often one-of-kind items and the bargains tend to disappear quickly.  By mid-morning I had purchased a good sized NEMA enclosure (steel box with weather tight gasketed door) and a Harris 22.2 telephone butt handset (tester).  I plan to use the NEMA box to create a cable entrance box with lightning protection for RF transmission lines, AC power lines, and control lines.  I got the telephone test set because it will allow me to hook up to the phone line the same way the AT&T technicians do, and because it is not the sort of thing most folks have in their home.

Bruce (W8RA) gave a short shopping list to Steve (N8AR) yesterday at breakfast.  Mike (W8XH) spotted a matched three-piece set of vintage Heathkit gear, one piece of which was on Bruce’s list.  Steve looked at it and they got Bruce on the phone.  Apparently it was close enough to what Bruce wanted that Steve bought the whole set for him as the seller was not willing to sell them separately.

We then moved to the inside vendors, most of whom were selling new merchandise at fixed prices.  There was some used equipment, however, and I bought an Icom CI-V interface set.  This device will allow me to interface our Icom IC-7000 and/or IC-706 to, and control them from, a computer using something like Ham Radio Deluxe (HRD) software.

I also got to meet and talk to Norm, from Norm’s Fabrication in Adrian, and his wife, who is president of the Adrian Amateur Radio Club.  Norm is a welder, and his side business is fabricating tower parts out of steel and aluminum for fellow hams.  If I cannot get what I need from Heights Tower Systems, Norm may hold the key to getting our used tower erected.

A very classy portable ham radio station (go box).

A very classy portable ham radio station (go box).

A number of other hams from the South Lyon, Novi, Livingston, and SEMDXA radio clubs were there.  I brought my camera and tried to get photos of our club members for the club website.  None of us won anything from the hourly drawings (must be present to win) and we left shortly after noon to meet up at the local Steak-n-Shake for lunch.  I had not eaten breakfast so I enjoyed my garden salad and French fries.  I had a good chat with Dave (K8ESQ), the current president of SEMDXA, and Don (N8CAK) from SLAARC.

We had a good chat on the drive back, stopping briefly at the Michigan Welcome Center on US-23 northbound shortly after entering Michigan from Ohio.  We dropped Steve off at the Lee Road Park-n-Ride and helped him unload the Heathkit equipment.  When we got back to Mike’s I moved my purchases and personal gear to my car and then spent some time examining his Heights tower, especially the fold-over mount.  After studying the parts and the geometry of the design I had a much better understanding of how it works and what we need to get our tower erected and fully operational.

On the way back to my house I got a call from Darryll letting me know he would be out in the morning as long as someone would be home.  Back home I unloaded everything and moved Linda’s car to the side parking pad to make space for Darryll’s truck in the morning.  It was nice to have a day away from our house and property projects.

I spent a little time checking e-mail and websites and off-loading digital photos until Linda called me to dinner.  We had leftover kale salad, quinoa with pineapple and nuts, fresh steamed broccoli, and corn-on-the-cob.  After dinner I recorded the events of the last few days in rough drafts of separate blog posts.  By 10:15 PM the early start and long day finally caught up with me and I turned the lights out and drifted off to sleep.

 

2014/08/10 (N) Kathi Comes To Visit

Leave a reply

Kathi Slater is a long-time friend, the mother of three girls who went through middle and high school at the same time as our children.  Her oldest daughter, Emily (who is now an MD) was one of our son’s best friends in high school.  Kathi ended up working at Metropolitan Bakery with Linda and is still there.  We have been trying to find a mutually agreeable time for her to come see our new house and today was finally the day.

Kathi arrived around 10:30 AM.  As with all first time guests we gave her a tour of the house and then, being another gorgeous summer day, we walked the property.  After the tours we settled in at the table on the deck under the shade of the umbrella and had a nice long chat.  Linda made her wonderful chickpea salad and served it sandwich style for lunch with sourdough pretzel nibblers, fresh grapes, and sweet cherries.  She left to return home around 2 PM.

I worked at my desk on website usernames and passwords until 5:30 PM.  For dinner Linda made sautéed green beans and a dish with whole grain macaroni, cannellini beans, kale, other ingredients, and spices.  Both dishes had a hint of garlic and red pepper flakes; just enough to elevate the dish but not so much as to dominate or overwhelm the primary flavors.

We finished eating a little after 6 PM and I had to leave for the 6:30 PM meeting of our ham radio club.  The meeting was well attended with several of our newest club members there.  After a short business meeting we had a brief introduction by Mike (W8XH) to ham radio projects that can be done with the Arduino (and similar) micro-controllers.  Mike and Steve (N8AR) then led a discussion on the subject of antennas; specifically simple ones that can be built fairly easily.

I got home rafter 9 PM and had a piece of watermelon.  We stayed up a little later than usual and decided to turn in without watching an episode any of the TV programs we are currently following.

 

2014/05/08(R) Toad Lights

Leave a reply

The spring peepers are in full voice this time of year, but they do not wear headlamps.  In fact, they are frogs, not toads.  In the world of RV’s a car that is towed behind a motorhome is often referred to as a “towed” (noun) or “toad.”  Like anything being towed, the car has to have functioning tail lights, brake lights, and turn signals.  The existing lights on the car are often used for this, but there can be issues with arrangement, especially on newer vehicles.

Our Honda Element came equipped with a second set of rear bulbs that are not tied into the cars lighting circuits.  On the way home from Florida they quit working.  Visual inspect had revealed that the 6-pin connector on the bus had a couple of damaged pins.  As soon as we got home I picked up a new connector from a local RV store.  With a forecast high temperature of 81 degrees F, and no rain, today was the day to install it; but not until I had taken care of another important chore.

Steve (N8AR) arrived a little after 10 AM pulling Bruce’s (W8RA) enclosed trailer.  We took a few minutes to look at my proposed site for the communications tower and then headed over to Wayne’s (KD8H) place to pick up the tower sections and related components I had purchased on Monday.  We got there right at 11AM.  Wayne greeted us in the driveway and directed us around behind the house.  We loaded the steel fold over mount, motor, rotator, and bearing plate in the front if the trailer and then drove back to where the tower sections were stored and loaded those in.  The trailer had about 10 feet inside, front-to-rear, and we were able to get everything in and close/latch the doors.  We were on our way back to my QTH by noon.  By 1 PM we had unloaded everything, stacked the tower sections on the rear/lower deck, and stored the other components in the garage.  I walked Steve through the proposed pole barn site and then he headed home to hang drywall.

I gathered up the tools I needed for the connector project and arrayed them at the rear of the bus.  Simple projects never are, and this was no exception.  I removed the two screws that hold the connector into the bumped fascia and the discovered that I could not pull it out more than a 1/4 inch.  The connector housing has an insert with the pins on one side (facing out) and the wire connections on the side (facing in).  The insert is retained by a small screw on the top of the housing.  To work on this assembly you have to be able to pull the housing out far enough to remove the retaining screw.  You then need to have enough loose wire behind the connector to allow the insert to come out the front of the housing far enough that you can get to the small machine screws that that hold the wires.

The problem was that I did not have the necessary amount of loose wire.  There was plenty of wire, it just wasn’t loose.  I had to clip about a half dozen zip ties in the engine compartment and along the underside of the rear bumper, and remove a cable clamp, but I eventually freed up enough wire to pull the connector housing out far enough to work on it.

The wire connections on the insert were not done in a standard way per the directions that came with the new connector, so I made a diagram of how they were done.  (I should have rewired both the bus connector and the cable end to be standard, but I plan to replace this whole setup with an EZ*Connector system this summer.)  I disconnected the wires, which freed the insert, and slid the old housing off the end of the wire bundle.  I cleaned up the ends of the four wires, stripping away 1/4 inch of insulation and trimming off frayed strands.  I slipped the new housing over the wires, made the connections to the back of the insert, slid the insert into the housing, and secured up it with the retaining screw.  I slid the housing back into the bumper fascia and secured it with the two screws.

Before dressing all the wires I pulled the car behind the bus and connected the electrical cable between them to test the lights.  I connected the bus chassis batteries (there are two switches for this) and turned on the left turn signal.  All the lights on the bus were fine, but I still did not have lights on the car.  🙁  I had also had problems previously with the plug and socket on the car so I jiggled the connector and the lights started working.  I verified that I had tail and turn lights but could not test the brake lights as that takes two people.  (I could have turned the ignition on and that would have caused the brake lights to come on since the emergency/parking brakes were set.)

I suspected the problem was in the connector on the end of the cable, but it was sufficiently corroded that I could not get it apart.  I decided to spray all of the old connectors (3) with De-Ox-It, including inside the cable ends.  I then sprayed all if the connectors, including the new ones, with De-Ox-It Gold.  I plugged the cable back in to the bus and the car and retested the lights.  Everything was working, so I secured the wiring on the bus with new zip ties, put my tools away, and closed everything up.

Sometime during the afternoon I got a call from Bruce (W8RA) and took a break from the electrical work.  He had a friend who had purchased a used full-size tractor to pull a large 5th wheel.  The tractor had a KVH Trac-Vision R5 in-motion satellite dish and the owner wanted Bruce to help him get it working.  Bruce knew we had a motorhome and thought I might have some insight into how to do this.  The only advice I could offer was based on the satellite dish and electronics that were on our bus when we bought it.  In addition to the dish on the roof and the receiver in the coach there was a third box that went in-between the two.  I suspected that the KVH had something similar, but I wasn’t sure.

Linda had been babysitting all day so we had an Amy’s Indian dish with a nice salad for dinner.  It had been a warm, physical day so I started a load of laundry and we just relaxed after dinner.

 

2014/05/07 (W) Plumbing

Leave a reply

After breakfast Linda headed to Ann Arbor to babysit our younger grand-daughter.  I had a long list of things to do at my computer today, and planned to spend the day inside at home doing them.  I did not manage to do most of them as I ended up doing other things instead; so much for plans.

Wednesday is trash day (sorry, Prince Spaghetti), so I got the trash to the curb.  (I know, I know, how have I managed to arrange such an interesting life?)  A box of Bus Conversion Magazines arrived yesterday, so I opened it to check the contents and then e-mailed the publisher that all was well.

We do not have curbside recycling at the house the way we did in the previous one, so we have to take our recyclables to a drop-off center run by Recycle Livingston.  The center is open Wednesdays and Saturdays.  On her way out the door Linda reminded me that I had to take the recyclables to the center.  We keep a set of cardboard boxes on the floor in the pantry and sort our recyclables as they become available.  I loaded them in the car for later.

At some point in the past the shower diverter in the bathtub quit working, so that had been on my “to do” list for a while.  Coincidentally, while we were in Florida I had seen an episode of “Ask This Old House” that dealt with this exact repair!  I had to use a large pipe wrench to unscrew the old bathtub spout/diverter as the threads were corroded.  With the old diverter off I now had a fairly good idea of what I needed in the way of a replacement part.

I had been putting off fixing the leaky dishwasher fresh water connection but today was finally the day to tackle that project.  As I was thinking about heading to the recycle center, and then to Lowe’s for plumbing parts, I got a call from Steve at Village Landscape Development (VLD).  He wanted to swing by and go over the front stairs and rear retaining wall projects again and get us on his schedule.  We agreed on 1 PM.  It was 11:30 AM, so I had just enough time to drop off the recyclables and get a new diverter from Lowe’s.

Steve (VLD) came by and we walked through the two projects.  We were on the same page and settled on tentative start and completion dates, so we signed an agreement and I gave him a deposit.  After he left, I called Wayne (KD8H), set up to get the tower tomorrow at 11:00 AM, and then e-mailed Steve (N8AR) to let him know the date/time.  He had permission to use Bruce’s (W8RA) closed trailer to help me with the tower.

Back at the dishwasher I turned the water supply on and the connection didn’t just drip, it spurted.  I redid the connection with pipe thread compound instead of Teflon tape but it did not help at all.  I tried tightening it and it got worse.  It was clearly time to rethink my approach.

I find that a good way to rethink my approach to a problem is to do something else, so I installed the new diverter for the bathtub/shower in the hall bathroom.  It only needed to be threaded on hand tight as it is not a pressurized fitting.  Water either flows out the spout into the tub or gets blocked and forced (diverted) up to the shower head; a pretty simple device, really.  It was not quite the right length and left a 1/2 inch gap between the base and the wall tile.  At least this way I could see if any water was leaking out the back end.  🙂  It wasn’t, so I let it go for now.

I returned to the dishwasher problem and took another look.  It appeared that the rubber seal (O-ring) in the end of the hose may have gotten nicked or mis-shapen, perhaps from over tightening.  There was no indication of a leak between the 90 degree elbow and the dishwasher inlet.

I headed back to Lowe’s for a new 8’ dishwasher connection hose.  I could not purchase just the hose; it only came as a kit with the 90 degree elbow and another adapter, which turned out to be fortuitous.  I noticed that the instructions did not call for Teflon tape or pipe thread compound and I verified that with the associate in plumbing.  I also picked up a decorative filler plate for the diverter.

The flexible water line connects to the lower left front corner of the dishwasher, loops underneath the unit, goes through a hole in the adjacent cabinet at the lower left rear, goes through the other side of that cabinet into the space under the corner sink cabinet bottom, and finally emerges through a hole in the floor of the cabinet along with a water pipe.  The only way to run the new flexible line, without removing the dishwasher and disassembling cabinets, was to attach one end of the new line to the dishwasher end of the old line and use the old line to pull it through.  Zip ties have lots of uses, and this is one of them.

Before making any connections I read the instructions again.  The connections at the end of the hose were to be “finger tight plus 1/4 turn.”  Although “finger tight” is an incredibly imprecise term–some number of inch-pounds would be precise–these directions clearly indicated that over tightening was a bad thing to do.  I connected the line at both ends following the directions as best I could and opened the supply valve a little.  No more spurting but I still had a drip leak and shut off the water supply.  I knew the hose was OK so it had to be the elbow.  I had to pull the dishwasher part way out to get to the 90 degree elbow.  (This why I installed an 8 foot hose.)  After I got it out I examined it and did not see any obvious thread damage or cracks, but there was some pitting and one pit in particular looked like it might be a through pinhole.  No matter, it was trash.

I installed the new elbow using pipe thread compound on the male NPT pipe threads that go into the female NPT fitting on the dishwasher.  These kinds of fittings are always a bit tricky.  They have to be tight enough to not leak, without overdoing it, and they have to be oriented a certain way to allow something else to connect to them; in this case the supply hose.  I reattached the flexible hose, turned on the water supply, and voilà, no leaks!  As long as I was on a roll I unscrewed the bathtub diverter, slipped the decorative spacer over the pipe, and screwed the diverter back on, lining it up carefully with the spacer and getting it snug but properly aligned.  Even though it took most of the afternoon I had successfully completed two plumbing jobs in one day.

 

2014/05/04 (N) Northwest Winds

Leave a reply

The weather yesterday was mostly cloudy with occasional light rain and the winds came up strong starting in the afternoon.  They tapered off by bedtime but resumed a hard blow this morning with low, puffy, white clouds streaming in from the northwest and making the trees dance.  It was a brighter morning than we have had most of the week as the sun played hide-n-seek with the clouds.  The temperature remained cool, making for a brisk day, but it was a nice change from the cool, overcast dreariness of the past week.  Except for Thursday, when the high temperature is supposed to hit 80, the daily high temps will be around 60 all week.

Linda made her scrumptious blueberry pancakes for breakfast and then went for a walk.  She had barely left the house when she returned, very excited, to tell me she had just seen a young albino deer running through our yard.  By the time I got outside it had moved on to the woods west of our property.  We often see the same deer day-after-day as they travel their circuit, so I also hope to see this one someday.

After checking in on the blogs I follow using the Feedly app on my iPad2 I made a couple of corrections to a recent blog post, approved a comment from our daughter-in-law (the first one has to be approved), and deleted the 59 spam comments that the Akismet plug-in/service trapped since last night.  I put a load of laundry in the washer and then spent some time looking online for a padded case for my new laptop computer and a replacement for one of our APC SmartUPS units that has failed.

With the move to tablet computers, the choice of laptops is diminishing, especially those with larger screens, and along with that fewer choices for accessories such as cases.  In the past 14 years I have always purchased larger roller cases, with separate cases for the computer that fit inside, as my laptop traveled with me every day everywhere I went.  I had the most recent of these cases with us in Florida and, after getting the computer/case and accessories out of it, I stored it in a closet (where it tended to be in the way).  The next time I touched it was when I unloaded it from the bus to bring back into the house.

It was clear from that experience that I do not need another roller case.  I do, however, want something that will protect my new laptop computer.  I think I have narrowed the choice down to the Everki Advanced or the Everki Lunar, both available through Amazon Prime.  The Advanced is very reasonably priced at under $40 and has generally favorable reviews, mentioning the ASUS “Republic of Gamers” (ROG) models in particular.  The Lunar has more storage space, and also has generally favorable reviews, but is over three times the price at just under $130.  Posts on the ASUS ROG Forum seem to favor one of the Everki backpack models, but I do not want a backpack style case.

Our failed APC uninterruptible power supply is a Smart-UPS SUA1000.  By trading it in on a SMT1000 we can save $75 off the retail price.  I need to confirm that the discounted price includes return shipping; the SUA1000 weighs 48 pounds.

I revised the RVillage Quick Start doc I created for the GLCC, CCO, and FTH RV clubs, making it generic for use by Bus Conversion Magazine or anyone else.  I then uploaded it to a new RVillage page on our website and revised a couple of other pages to link to the new one.  I then uploaded blog posts for the last three days.  I set up my new laptop in my office and installed seven more updates.

At breakfast yesterday I got a tip from Paul (N8BHT) on a used tower.  He e-mailed me the owner’s contact information later.  I called the owner, Wayne (KD8H), this afternoon and got a little more information about the tower.  It is an aluminum Heights Tower, 80 feet, with Fold-Over Kit (FOK) including the drive motor, a rotator and antenna mounting plate.  It is already on the ground and disassembled into sections.  Wayne is retired and I will likely go look at the tower tomorrow afternoon.  I e-mailed Paul (N8BHT), Mike (W8XH), and Steve (N8AR) to see if they were available to go with me.

Linda made lentil loaf for dinner with baked yams and fresh asparagus.  After dinner I drove to South Lyon for the May meeting of the South Lyon Area Amateur Radio Club.  SLAARC usually meets on the 2nd Sunday of the month but pulls the May meetings forward a week to avoid Mother’s Day.  Our topic of discussion this evening was the upcoming ARRL Field Day operating event, which takes place the last full weekend in June.  We had a couple of new hams at the meeting and afterwards several of the guys helped Christine, KD8VEA, get the PL tone set correctly on her radio so she was able to participate in a group QSO with Steve (N8AR), Mike (W8XH), Fred (AC8VL), and myself on the drive home.  In spite of what many people think, including some older/former hams, amateur radio is alive and well in the North America and all over the world.