Tag Archives: SR-19 (IN-19)

2015/09/20 (N) On To CCO

Leave a reply

I woke up at 7:30 AM but lay in bed until almost 8 AM.  It got down to 50 degrees F outside last night and was cool enough in the bus for really good sleeping under several layers of sheets and thin blankets.  Linda was still sound asleep so I slipped into my sweats and walked over to the meeting room for coffee and conversation.  I skipped breakfast as I prefer not to eat before I have to drive the bus for any length of time.  I would normally skip the coffee too but we did not plan to leave until noon, so I figured I had time to process it.

Linda eventually got up, got dressed, and joined the other women in the kitchen for conversation.  Tim Olsen and Karl Crigger had not seen our remodeling project yet so we headed to the bus.  Tim was particularly interested in what we had done in terms of furniture and we had a nice chat.  All around us the other rally participants were in various stages of preparing for departure and both Tim and Karl took their leave to attend to their own departure routines.

Linda managed to get other people to take various pieces of chapter-owned food-related equipment and supplies with them so we did have to take them home, store them, and possibly have to get them to someone later.  She started preparing the inside of our coach for departure while I installed the hitch back into the receiver on the bus.  Most of the rally attendees had left by 11AM or were getting ready to pull out so we decided we would go too.

I fired up the bus engine and then disconnected and stowed the shore power cord while the engine warmed up and the chassis aired up.  The site directly behind us on the other side of the road was empty, and it would be a much easier departure from there than from our site, so I backed the coach up while Linda served as spotter.  Kathy came over so Linda showed her our interior remodeling project while I pulled the car around behind the bus and connected it to the hitch.  Linda caught up with me and helped finish preparing the car for towing while I opened the air valve for the auxiliary brake system on the car.  She checked that all of the bays were closed and locked, said “so long” to several folks, and got on board.

We were ready to pull out when Dan stopped by to say “thanks” for a great rally and then Mike stopped by to wish us safe travels.  There are quite a few people in GLCC that we have never met, but most of the ones we have crossed paths with are genuinely nice people.  Many of us in the GLCC chapter are also members of an independent organization named Converted Coach Owners, AKA “CCO.”  Linda and I joined CCO in August 2014 but have never made it to a rally.  The annual Halloween Rally will be in Centreville, MI the weekend of October 17th.  Our bus should be usable then and we are seriously considering trying to attend.

I pulled the tag axle up and pulled out at 11:30 AM, driving around the back side of the activities building to get to the exit.  This route is open with easy, wide turns.  The more direct route has narrow roads with sharp turns, large trees close to the road, and low branches; not a big rig friendly route.  A lot of large motorhomes and 5th Wheel trailers use Elkhart Campground and I do not understand why the trees along this route are not trimmed up adequately.  We have encountered the same thing, however, at other RV parks.  I get the feeling that many people who own/operate RV parks have never owned/used an RV or at least never driven a large one through their own campground.

We discussed several different route options that might avoid construction delays but ended up taking CR-4 back west to SR-19 north into Michigan and picked up US-12 east.  The road construction between Sturgis and White Pigeon that delayed me for 20 minutes on Tuesday was finished and we rolled right through that stretch.  We stayed on US-12 to Coldwater, got onto I-69 north, and took it to the southeast corner of Lansing where we exited onto I-96 east.  We encountered our only road construction backup approaching the US-127 interchange at the southeast corner of the Lansing area.  We were through that soon enough and on our final stretch home.  We left I-96 at exit 133 and headed east on M-59.  The last few miles were the worst.  Hacker Road is as bad at the moment as we have ever seen it, more pothole than road, with deep, frequent ones at that, but we took it slow and made it home without breaking anything (as far as I know).

Linda made big salads for dinner which we enjoyed with a glass of Moscato.  She relaxed playing online games while I set up my computer and then checked into the SLAARC information net.  We watched the repeat of the last episode of Sherlock from last season and then went to bed.

 

2015/07/21 (T) A Long Day

Leave a reply

I was awake at 6 AM, and up shortly thereafter, even though I did not set an alarm.  I packed a change of clothes and a few toiletries and then gathered up my cell phone and iPad chargers, my iPad, and my checkbook.  I loaded the desk/pantry drawings and travel bag into my car and then did a temporary installation of the weBoost cellular booster.  I put the outside magnetic base antenna in the center of the roof and experimented with the placement of the inside antenna, eventually setting it above the passenger side sun visor facing down.  I backed out of the driveway at 7:05 AM and headed for Indiana.

I took Hacker to Golf Club to Latson with some thought of stopping at Teeko’s for coffee but decided to get some miles behind me first and proceeded to I-96 westbound towards Lansing.  I should have looked up the frequency for the Lansing area repeater, where Don runs a net Monday through Friday from 7 AM until at least 11 AM, but I didn’t think of that ahead of time.  I would also have had to figure out how to switch Mike’s Icom IC-2820H radio from memory mode to VFO mode.  Eventually I will, but not today.  Today was not about ham radio, it was about bus projects.

I took the Lansing Road cutoff to I-69 south and about 20 miles later took the Lansing Road exit at Charlotte.  I stopped at the Biggby’s Coffee not far from the highway and resumed my trip around 8:30 AM.  When Linda and I drove to Edwardsburg, Michigan to visit Coach Supply Direct on July 1st we discovered that M-60 was closed at Minden (between I-69 and US-131) and had to take a long detour.  Rather than risk having that happen again I headed west on I-94.  I had been playing with the cell phone booster but unplugged it and plugged in the Garmin 465T GPS instead.  I eventually saw that M-40 came all the way north to I-94 and decided to take it instead of US-131.

I had never been on this stretch of M-40.  The road was a good 2-lane at 55 MPH except going through small towns.  I drove through miles and miles of vineyards and eventually got to the charming (looking) little town of Marcellus where I discovered a large Welch’s plant.  I knew that a lot of the grapes grown in southwest Michigan ended up as Welch’s grape juice but I did not know where their processing plants were located.  Now I know where they have at least one.

When I reached the intersection with M-60 in Jones I stopped at the Shell station for fuel.  Regular unleaded was $2.52 per gallon which was better than I had seen so far during the trip.  Instead of continuing down M-40 to US-12 I put the address for Coach Supply Direct into my GPS and headed west on M-60 towards Cassopolis.  The GPS had me bypass Cassopolis by heading south on Calvin Center Road to Brownsville Road and then west to M-62 where I headed south towards Edwardsburg.

When I arrived at Coach Supply Direct it was locked up with no sign of Josh.  I called his 800 number and he answered, which I appreciated.  He was in western Pennsylvania heading home from a customer service call and said he could meet me at the shop after 4 PM.  We agreed that I would call him when I had a clearer picture of what time I could get back to his shop.

I left Edwardsburg and drove back on US-12 to Cassopolis Road which merges briefly with Old-102 and then becomes IN-19 (SR-19) in Indiana.  I stopped at Factory RV Surplus in Elkhart, which is on SR-19, to buy a special two-piece bracket for mounting the edge of a table to a wall.  I saw it on their website and luckily they had it in the store as well.

I proceeded south on SR-19 to US-20, went west to US-31, and took that south to the SR-25 exit at Rochester.  From there it was 22 miles to Logansport and a few more blocks to Jarel Beatty Cabinetry.  Jarel is a cabinet maker and a mutual friend of Butch Williams.  I have been talking to Jarel about the custom desk we wanted for the bus for several years and, more recently, about the pull-out pantry and HVAC duct and wiring chase cover.  The purpose of my visit was to deliver the design drawings for the desk and pantry and go over them with Jarel.  I got there around 1:20 PM and left around 5:50 PM.  After discussing the projects at length we agreed that I would change the design of the pantry so I did not leave those drawings with Jarel.  The Fulterer pantry slide had been delivered to Jarel so I took that with me as it turned out to be too wide for this project.

I set my GPS destination for Edwardsburg and it indicated I would arrive around 7:45 PM.  I called Josh to see if that would work for him and he said it would.  I headed north on SR-25 and then called Butch to let him know that I would not be able to stop and visit or spend the night.  That was probably just as well as he was in the emergency room when I called.  He had nicked his thumb in his table saw and was having it tended to.  I stopped at the Kroger in Rochester to buy some snacks for dinner and got a return call from Butch.

The drive to Edwardsburg was pleasant and took me on some more roads I had not driven before.  US-31 north to US-20 east was familiar territory but I exited at Elm Street (US-331 north) which bypassed the west side of Mishawaka and eventually took me up through Granger and onto M-62 in Michigan.  A few miles later I was at Coach Supply Direct in Edwardsburg where Josh was waiting for me.

I returned the Lambright Comfort Chair fabric samples and the MCD shade material samples (the reason for my visit) and we chatted for about 45 minutes.  Our new MCD shades had already arrived but I asked Josh to hang on to them.  We tentatively agreed that we would bring the coach to his shop on Monday September 14 to have the new chairs and shades installed.  The GLCC Surplus and Salvage Rally starts on Wednesday the 16th in Elkhart and Josh offered to let us park at his shop the evenings of the 14th and 15th with 30A electric.

I left around 8:30 PM and started for home.  Again, the initial route was familiar as I took US-12 east to M-40 north, to M-60 and stopped at the Shell station in Jones for the second time today.  I then travelled east on M-60 to Three Rivers where I picked up US-131 northbound.  Rather than continue east on M-60, which I presumed was still closed at Minden, I stayed on US-131 all the way to I-94 between Kalamazoo and Battle Creek.  On I-94 east I encountered a major traffic jam due to construction.  The highway was down to one lane and traffic was barely moving as people merged down and then gawked as they went past the very busy construction site.

The rest of the drive was uneventful and familiar as I left I-94 for I-69 north, stopped at the McDonald’s in Charlotte for coffee, and got back on I-69.  I took the Lansing Road cutoff to I-96 and rolled along eastbound to the M-59 exit on the far west edge of Howell.  Eleven miles on M-59 put me at Hacker Road and a few miles later I pulled into the driveway.  It was just after midnight when I arrived, about 17 hours from when I left, and I had put over 550 miles on the car.  I unloaded a few things from the car and then went straight to bed.

 

2015/06/02 (T) GLAMARAMA 2015 (Day 0)

Leave a reply

We were up at 7 AM and had cinnamon toast for breakfast but did not have coffee.  We checked various routes to the Elkhart County 4-H Fairgrounds (EC4HFG) and searched online for information about any possible road construction problem areas but did not find anything that looked problematic.  By 8 AM we had started preparing the bus and car for travel.  Linda walked over to Curtis’s coach to say “so long for now” but all the shades were down so she sent him a text message that we were on our way.  We pulled out of our site at 8:15 AM.  I pulled up clear of other RVs and stopped to wipe off the passenger side mirror which was obscured with dew.  I am always surprised that I don’t notice things like that before we start to move.

We took CR-4 west to SR-19 and went south, crossing over the Indiana Toll Road, to CR-6.  There are times of the day that this intersection would be very busy but traffic was light this morning and I had no trouble getting into the correct turn lane and completing the turn.  CR-6 is a 4-lane road and moved along nicely all the way to CR-17 except for a short lane closure for local maintenance.  We turned south on CR-17, took it down to US-20, and headed east.  As I expected, this stretch of US-20 was still very much under construction with only one lane open in each direction and no wide loads over 11 feet permitted.  Traffic was more congested and slower but it moved along.  When we got to SR-15 we turned south and ran along nicely until we got to a construction zone that had the road down to one lane with flaggers.  We waited patiently and eventually got through the bottleneck.  We were routed through a short detour and then finally entered Goshen.  We followed the SR-15/US-33 Truck Route and found ourselves in another one lane construction zone with flaggers, and a train thrown in for good measure, but we eventually made it to our turn onto eastbound CR-34 (Monroe Street) and drove the final mile to Gate 5 of the EC4HFG.

We were directed to the staging area where we unhooked our car.  We were then led to the area reserved for our Great Lakes Converted Coaches Chapter and backed into our site.  The Laughing Raven Touring Co. bus was already parked in our area.  We saw this bus at Elkhart Campground while walking but did not realize it was headed to the rally.  The owner, Mark Lovegreen, is not a member of our chapter but wanted to park with other buses and we were glad to have him.  I reserved 12 parking spaces, the parking crew gave us 13, and I had a least one coach that was not going to show up so we had the space.  Also, Pat and Vicki Lintner got parked on hard surface nearby as the ground in our area was very soft when they arrived on Sunday.  In addition to being our chapters National Director Pat is the Senior VP of GLAMA would normally be parked elsewhere except that he likes to park with the chapter.

While Linda set up the interior and made coffee I hooked up the electrical power.  Our main 50 A circuit breaker did not want to set.  I finally pushed the lever hard enough to move it but did not like the way it sounded and did not get power to the coach.  I have indicator lights that told me there was power at the coach end of the shorepower cord but I verified that using my VOM.  I removed the cover from the disconnect box in our coach and verified that there was voltage present on both the L1and L2 bus but no voltage present on the output lugs of the circuit breaker.  Bummer.

Linda turned off the 30A supply circuit breaker and unplugged the cord.  I checked with the VOM that there was not voltage present and then unclamped the L1 and L2 load wires, removed them from the circuit breaker, and then removed the breaker from the box.  I tested it for continuity and with the lever in the “ON” position and one leg showed a short but the other leg showed an open.  That meant I should have had voltage coming through to our Progressive Industries EMS on one leg but I never did.  Regardless, we needed a new breaker as at least the one side had clearly failed.

The circuit breaker was a Square D QO style 2-pole 50A model.  I knew that Lowe’s carried QO breakers so Linda searched for the nearest store using her phone.  There was one on US-33 back towards Elkhart so Linda fixed a “to go” cup of coffee for me and I headed there.  They had a good selection of QO breakers including the 50A one that needed.  I looked briefly at refrigerators and noted that they had the Frigidaire model we are considering in white, black, and stainless steel.  Maybe we will drive up later to look at them.

I took a different route through Goshen to avoid the one lane construction zone.  Back at the coach I refilled my coffee and got to work.  As bus repairs go this one was pretty straightforward.  Getting the two load wires into the circuit breaker clamps was a bit tricky but I got them in.  The QO breakers snap onto a mounting rail at the bottom and then the contact fingers snap over two blades at the top.  All of that took a bit of pushing but I got it in.  I put the cover plate back on, reconnected the shorepower cord, turned on the supply breaker, and turned on the coach breaker.  We had power to the coach but it shut off.  I reset the breakers (turned them full off and then back on) and everything appeared to be fine and the power did not trip out after that.

With our power problem averted Linda walked over and got us registered and signed up for one of the few remaining time slots to work in the rally office.  She had volunteered to work registration but most of the time slots were already filled and the only thing left was Saturday morning.  Shortly after she returned to our parking area three more buses showed up:  Bill and Karen Gerrie, Mike and Kathy Dickson, and Joe and Mia Temples.  Next in were John and Paulette Lingafelter followed by Don and Sandra Moyer.  Late in the afternoon Scott and Tami Bruner arrived.  That only left a couple of coaches arriving tomorrow.

I borrowed a sledge hammer from Joe Temples and pounded three pieces of rebar into the ground to serve as supports for the clubs three flag holders.  A number of RVs around the rally site had the same design and I suspect that there was an article in the magazine, or something online, about how to build these.  They are very simple and inexpensive, can be taken apart for transporting, and rotate with changes in wind direction.  Our club as a USA flag, a Canadian flag, and a Chapter flag.

We all stood around in small, shifting groups talking about this and that.  I laid down around 2 PM and napped for about 90 minutes.  We are conveniently located to one of the bathroom/shower facilities so Linda took a shower there so as to not use up the good water in our tank.  By 6 PM most of our group had left to go out to dinner.  We ate around 6:30 PM, having a nice, light supper of cold chickpea salad on a bed of power greens.

A little before 7 PM we drove back to Lowe’s to look at refrigerators.  It turned out that the ones I saw were the 18 cu. ft. models not the 16 cu. ft. one we need/want.  The 18 cu. ft. model would fit in our alcove but take up the entire width leaving no space for a pull out pantry.  We looked at solar powered spotlights for illuminating the flags at night but at $18 each decided not to buy any as we needed at least three and would ultimately need the approval of the club to buy them.  We stopped at the Martin’s market on US-33 and picked up a deli tray brochure and a few grocery items.

Back at the rig there were lots of folks gathered in conversation.  Linda and Vicki went for a walk while I chatted with Mark (from Alaska) and Scott.  Scott and Tami recently had a new Whirlpool residential refrigerator installed in their bus so I went to see it.  It’s a very nice French door fridge with lower freezer drawer but is too tall for our alcove.  This is the style refrigerator Linda wanted but we could not find one sized to fit our space.  Bill Gerrie helped me get the U.S. and Canadian flags off of the holders.  Linda and Vicki returned just in time to help fold them properly.  With darkness came much cooler temperatures and everyone retreated to the warmth and comfort of their coaches.

Someone reminded us that Paul’s Seating in Elkhart was a good place to shop for furniture so Linda Googled it and found the website.  There were pictures of lots of chairs, including a barrel chair, but no information about dimensions, fabric options, or prices.  We will likely go to Martin’s in the morning and place a food order and then drive in to Elkhart and find Paul’s.  The critical path for our interior remodeling project goes directly through the selection of furniture and then through the refrigerator replacement so we are starting to feel some pressure about getting decisions made and orders placed.