Tag Archives: SLAARC Info Net

2015/11/22 (N) Repackaging

Leave a reply

My lower back bothered me all night, so I did not sleep well, but we both got up at 8:15 AM, took showers, and got dressed.  My right lower back seemed to have gotten worse overnight.  I pulled a muscle yesterday and they tend to take quite a while to heal.  Not good.

The view of our rear deck from our dining room the morning after our major snowstorm. It’s pretty if you don’t have to go outside to pack a bus or drive in it.

The view of our rear deck from our dining room the morning after our major snowstorm. It’s pretty if you don’t have to go outside to pack a bus or drive in it.

According to the National Weather Service newsfeed on The Weather Channel iPad app Howell, Michigan got 16.5 inches of snow from yesterday’s winter storm, the highest in Michigan.  The highest accumulation in the country was 18 inches somewhere in South Dakota, so we were very close to that.  The official amount was no doubt recorded at the Livingston County Airport about 11 miles west of us on the west side of Howell, but based on what we see on our deck we got at least a foot of snow here at the house.  It was sunny but only 25 degrees F when we got up.  The high temperature was forecast to only reach 30 and the low tonight is forecast to be 18.

Linda made vegan pancakes for breakfast.  She cooked blueberries into hers but I had mine on the side.  I think the blueberries add additional liquid to the batter and keep the pancakes from cooking properly, but Linda likes the way they turn out.  I made a pot of coffee with the last of our Ethiopian Yirgacheffe beans.  I took some Ibuprofen along with my usual morning pills.  Linda got the heating pad out and I sat with it against my lower right back on the living room sofa while we drank our coffee.  In spite of having a lot to do between now and Thanksgiving Day, we got a slow start to our day.

Linda cleared our front sidewalk so she could get to the front door of the bus.  She also shoveled a path to my car, which I parked behind the bus yesterday, and cleared the snow off of it.  She checked the snow depth with a ruler at several places on our rear deck.  It was 13 inches.  Not 16.5 inches, but it’s still a lot of snow, and it could certainly have been deeper out in the yard.

Her agenda for the day was to vacuum the inside of all the cabinets in the bus, dust the woodwork, and clean the counters and mirrors.  I exchanged some text messages with Chuck including a couple of photos.  I sent one of our bus buried in snow and he sent one of the palm trees and lush vegetation on the unoccupied lot next to theirs at Pelican Lake Motorcoach Resort.  Chuck said it has been too warm to play golf.  I did not know that was even possible but I did not feel too sorry for him.  I sent an e-mail to Butch to let him know I had delivered the antique SUN Electric distributor tester to Bill a week ago Friday.

I resumed working in the garage and spent most of the day repacking my tool boxes.  My objective was to reduce the number of boxes from five to four while maintaining some sort of reasonable logic to how they were organized.  I took short breaks throughout the day to get off my feet and had a few pretzels with hummus for lunch.

Sometime during the afternoon Kerry showed up and plowed as much of the concrete driveway as he could.  Linda must have been vacuuming in the back of the bus and I was working in the garage (with doors closed) so neither of us realized he was there until after he was gone.

I decided that I needed some additional storage boxes for organizing small parts so I drove to Lowe’s hoping to find the Stanley boxes I already have.  They had similar boxes from a different manufacturer but not the exact ones.  I tried The Home Depot but liked the boxes at Lowe’s better so I went back there and bought six, three with 10 deep bins and three with 17 medium bins.  I stopped at Meijer’s for orange juice and picked up a few other things.

When Linda was done cleaning the bus she started loading the things onboard that she had ready.  She got almost everything on board that was staged in the middle bedroom and the kitchen.  She then made three more batches of granola.  That made nine batches since Friday evening, eight of which are in the freezer.  Linda thinks a batch will last at least two weeks if have granola every other day.  If that proves to be true we should have enough granola with us in the bus to get through the end of March.

By 5:30 PM we were both ready to stop for the day.  I changed into my robe and sat on the living room sofa with the heating pad on my lower right back.  We spent 45 minutes considering possible waypoints between here and Williston, Florida.  We did not come a decision but it is very likely we will stop at two of the same places we used two years ago, the Oh Kentucky campground in Berea, Kentucky and the KOA near Cartersville, Georgia.

The Oh Kentucky RV Park in Berea is just west of I-75 at an interchange.  It wasn’t fancy but provided easy in/out access and would allow us to plug in for the night.  Just east of the Interstate at the same exit is a Walmart where our friends, Chuck and Barbara, stayed on their way south a few weeks ago.  The RV park options north of Atlanta, Georgia are surprisingly limited.  The Cartersville Castle-White KOA is convenient to an exit off of I-75 and also provided easy in/out access.  Staying there Saturday night means we can drive around Atlanta on I-285 on Sunday morning, our favorite time to bypass major cities.

Our final waypoint before going into Williston Crossings on Tuesday, December 1st will probably be Mayo, Florida where we can boondocks for two nights at John Palmer’s place.  This itinerary would have us traveling about 400 miles on Friday, 300 miles on Saturday, 340 miles on Sunday, and 75 miles on Tuesday.  Friday would be a longer drive by about 2 hours than we normally plan, but very doable.  Also, this time of year we like to get as far south as quickly as possible.

Linda opened a bottle of Leelanau Cellars Mixed Berry Winter White wine to have before, during, and after dinner.  For dinner Linda cooked a squash and heated up some frozen corn and mock chicken tenders (vegan).  After dinner I tried to check my e-mail but our Internet connection had slowed to an unusably slow speed.  At 8 PM I participated in the SLAARC Information Net and then came back upstairs and went to bed.  We both took some Tylenol PM at 11:30 and then turned out the lights.

 

2015/11/15 (N) Tiling the Cockpit, #2

Leave a reply

Having had a larger than normal meal later than usual last night, and gotten to bed later than usual, we did not get up this morning until a little after 8 AM.  I made coffee but we were not hungry.  By the time we finished our coffee it was approaching 10 AM but once we got to work in the bus we were on task until 7:30 PM with only a short lunch break at 1:15 PM.

Bruce dry fits floor tiles on the navigator seat platform. (Photo by Linda.)

Bruce dry fits floor tiles on the navigator seat platform. (Photo by Linda.)

We cut and dry fit the tiles for the platform floor and walls.  We had to take time out to use the oscillating saw to undercut the bottom edge of the face board on the passenger side front vertical wiring chase.  With all the tile cut and fitted we determined the order in which we would install them.  We started with the platform floor and the first six tiles of the landing.  I also had to fashion some shims to make sure the tile in the driver-side rear corner of the platform would be installed in exactly the right location.  This would be the first tile installed and if it was even slightly misaligned it would throw all of the other tiles off.

Bruce spreads Armstrong vinyl adhesive on the navigator platform. (Photo by Linda.)

Bruce spreads Armstrong vinyl adhesive on the navigator platform. (Photo by Linda.)

I marked the edges of all the tiles on the underlayment and then we pulled them up in the reverse order of installation.  Linda prepared some soapy water to use for cleanup of the tools and tiles.  I spread the Armstrong vinyl adhesive and Linda cleaned the trowels when I was done.  We waited for it to cure to the point where we could set the tiles.  Even with two heaters going in the front of the bus the adhesive took about 50 minutes to cure to where it would not transfer when touched.  Once it reached that point we had roughly an hour to set the tiles but it only took about 20 minutes to install them.  I used a large rubber mallet to help set them, pulled the spacers, wiped the edges with a wet paper towel, and then walked on them in lieu of using a 100 pound floor roller which would have been awkward at best to use on such a small area and not worth the time and expense to rent from The Home Depot in Howell.

Bruce installs intricately cut floor tiles in the cramped front of the driver’s area. (Photo by Linda.)

Bruce installs intricately cut floor tiles in the cramped front of the driver’s area. (Photo by Linda.)

As soon as the first group of tiles was installed we pulled up the remainder of the floor tiles from the landing and driver area.  Linda got some paper grocery bags and painter’s tape and masked off the platform floor along the back and side wall.  I spread adhesive on all of those areas and then Linda once again cleaned the tools.  Approximately 50 minutes from when I started spreading adhesive l started setting the tiles and about 20 minutes after that they were all installed.  Once again I used a large rubber mallet to help set them, pulled the spacers, and wiped the edges with a wet paper towel.  I walked on the floor tiles but had no way to further set the wall tiles.

We were done by 7:30 PM.  Linda cleaned up the tools and water bucket while I closed up the bus.  She started fixing diner and I got out of my work clothes and put on my robe.  Dinner was a nice salad and an Amy’s Roasted Vegetable Pizza; vegan, of course.  We finished the Organic Natural White wine from Frey, but we did not necessarily enjoy it.

Following dinner we relaxed in the living room for a while and I responded to a series of text messages from Kristine Gullen.  I missed the SLAARC information net at 8 PM because it just slipped my mind.  We were in bed by 10 PM and I watched Part 1 of the 2-part PBS American Experience program on Walt Disney while I finished this post.

 

2015/10/25 (N) Bus Dinner

Leave a reply

It was 44 degrees outside when we got up this morning but cozy in the house.  We were out of Linda’s homemade granola so we had oatmeal for breakfast.  It’s a nice change of pace on occasion and was a hot, hardy start on a chilly day.  I made a pot of Sweet Seattle Dreams coffee and we had a quiet morning in the living room.  We talked about going to the Howell Farmers Market, as today is the last day of the 2015 outdoor season, but did not need anything and given the temperatures decided not to go.  I changed into my work clothes at 10:30, went out to the bus, and turned up the thermostats to raise the interior temperature.

My focus in the bus today was tasks that I could not do alone.  I got my 15/16ths closed-end ratcheting wrench and removed the main retaining nut from the driver’s seat and from the front passenger seat.  Each of these nuts threads over a vertical stud that is fixed to the pedestal/riser which is in turn bolted to the floor.  In between the top of the riser and the bottom of the 6-way power base is a ball-bearing swivel plate which is centered on the mounting stud.  To get to these nuts I had to move the seats forward using the motorized bases and reach in from behind but I had good access and the nuts were not hard to loosen and remove.  I bought this closed end ratcheting wrench specifically for removing/installing these seat mounting nuts and it was worth every penny I paid for it.

With the nuts removed I unplugged the 12V DC power supply wires to each seat.  Linda and I were then able to lift the seats off of the pedestals without too much difficulty, carry them back into the kitchen (of the bus), and lay them down on their backs on the floor, which was protected with blankets.

The reason for removing the seats was two-fold:

  1. We were going to hang wallpaper on the living room walls where they merged into the cockpit and needed better access to those areas, and
  2. I plan to tile the floor and walls in the cockpit and entry this coming week and needed these seats out of the way in order to be able to do that.

Our next task, preparatory to hanging wallpaper, was to remove the walnut cover (half box) from the front eight feet of the passenger side OTR HVAC duct and wiring chase.  We set it across the two seats we had just removed to get it out of the way.

Bruce marks a piece of wallpaper on the dining room table in the house before cutting it.

Bruce marks a piece of wallpaper on the dining room table in the house before cutting it.

When we were finally ready to start wallpapering we needed three relatively short pieces; two to finish the driver side and one to finish the passenger side, at least as far as we intended to go.  I made a sketch for the shape of each piece, took measurements, and added them to the sketches.  The wallpaper is 26.5″ wide on the roll and the longest piece we needed was only 24″.  I got the 3′ and 6′ rulers from the shop while Linda got the roll of wallpaper.  We used the dining room table in the house to measure, mark, and cut each piece.  Although relatively small these pieces took some additional, careful, attention because they had to fit over, under, and around cabinets and window trim.  To make the installation easier I trimmed away as much of the waste material as possible before hanging the piece.

Linda partially filled two 5-gallon buckets with water, added soap to one of them, and brought them out to the bus while I retrieved the paint tray and liner and the 6″ pasting brush.  We laid out all of the wallpaper tools, put a towel on the floor, and set the paint tray/liner on the towel.  I poured the amount of wallpaper paste I thought we would need into the tray and started with the piece of wallpaper at the right end of the built-in sofa (towards the front of the bus).

As we had done previously everywhere else in the bus I applied the paste to the wall rather than to the back of the wallpaper.  The wall behind the sofa had been primed but the small strip above/behind the end cabinet and around into the cockpit had not been, so I used more paste in the unprinted areas.  This first piece required a lot of trimming so it took a while to hang but it looked good when we were done.  As I got each piece installed, with Linda’s help, she rolled the seams and then washed off the excess paste with a large sponge using the soapy water followed by a second sponge with clean water.

We continued along that wall towards the front of the bus with the second piece.  It did not require as much trimming as the first piece and went in a little faster and easier.  I overlapped the thin strip above/behind the cabinet with the first piece and cut through both of them to create a clean, tight seam.  When we hung wallpaper in our house many years ago all of the seams were done by overlapping adjacent panels and cutting through both pieces.  The paper we are using in the bus, which is actually vinyl, is installed by butting the factory edges together.  This certainly simplifies installation, and speeds it up a bit, but it is harder to get a perfect seam.  Still, it was the right choice for our motorcoach as it is washable and scrubbable and goes very well with the interior.

On the passenger side of the coach I pasted up the last section of the living room wall and part of the small section of wall under the trim on the window next to the front passenger seat.  I ended up cutting off a small part of this piece and installing in separately as the trimming required was intricate and awkward to do.

After installing the two parts of this third piece we decided to go ahead and paper a small triangular section of wall above the bottom window trim.  I got a scrap of wallpaper from the house that was big enough to cover the right triangle shape and cut it approximately to size.  I pasted the wall, set the bottom edge flush to the sill, pressed the back edge into its vertical corner, and trimmed off the excess.  This little section of wall was capped by a piece of walnut that ran at an angle along the bottom edge of the glass.  I trimmed off the paper at the bottom edge of the wood trimmed and tucked the paper in under the walnut.

The reason we did not wallpaper all of the small wall section below the window is that part of the plywood wall is severely water damaged and a piece of it rotted and is missing.  There is no practical way to replace the plywood and the only practical way to repair this area is to panel over it.  We could use thin plywood and wallpaper it but we have enough of the 1/4″ walnut veneered plywood that we salvaged from the old refrigerator to panel this area.

We were done with the wallpapering by 2:30 PM.  Linda cleaned off most of the tools and then took the two buckets of water out of the bus to pour them out and clean them.  I took the paint tray/liner, pasting brush, and some of the tools to the laundry room and cleaned them.  There was very little paste left in the tray liner so I had estimated quite closely on the amount I needed for today’s work.

The swivel mechanisms for the two front seats consist of two rings separated by ball bearings and interlocked around the inside edge.  They have an ‘A’ side and a ‘B’ side and one of them was installed ‘A’ side up and the other ‘B’ side up.  They also have a large washer.  The driver seat was installed with the washer between the swivel bearing and the power base.  The passenger seat had the washer directly beneath the retaining nut inside the power base.  Given these differences I could not tell the correct orientation and order of assembly by casual inspection of the pieces involved.  It is possible that the swivel plates are, in fact, symmetrical and thus can go in either way, but one of the washers had to be in the wrong place.

My interest in all of this was motivated, in part, by the fact that both of these seats have always wobbled since we bought the coach.  The new seats are firmly attached to the power bases which seem tight but may have some play.  I was suspicious of the swivels, however, as the main source of the play.  I studied the design for a while and came to some tentative conclusions.

When the swivel plates are installed the ring on the bottom (that sits on the pedestal) is not going to move as the pedestal is bolted to the floor.  The top ring, which will be in contact with the power base, is going to move relative to the fixed bottom ring when the seat is tuned.  I decided that the larger ring, which wraps around the inside edge of the smaller ring, should go on the bottom.  With regards to the washer it seemed to me that it should go directly under the retaining nut, allowing the power base to swivel relative to the nut without loosening it.  Further, placing it between the swivel plates and the power base would potentially prevent the base from fully resting on the swivel plate and allow the whole seat to wobble.

I will examine all of this again more carefully when we are ready to reinstall the seats.  For now, I took the two swivel bearings to the garage to clean and lubricate them.  After wiping them off I sprayed them with WD-40, worked them around, and wiped them off again.  I then sprayed them with garage door lubricant, worked then around again, and wiped them off.  Finally, I worked Red Tack ‘grease’ into the ball bearing race, spun the rings to distribute it evenly, and the wiped the outer surfaces clean.  After cleaning the grease off of my hands I took the swivel plates back to the bus, wiped the pedestal plates clean, and set them back in place.

We quit working around 3 PM so Linda could cut my hair and beard.  I then shaved, showered, and got dressed for dinner.  Linda showered after me but was dressed and ready to go before I was.  We made plans yesterday to meet Bruce (W8RA) and Linda (K4YL) at Carrabba’s in Novi at 5 PM for dinner.  We left at 4:30 and arrived in Carrabba’s parking lot just after 5.

The parking lot was not full so we knew there would not be a wait for a table.  Bruce and Linda were already there and had opted for a booth.  The booths will seat six adults so they have more table space than a table for four. They also offer a bit more privacy for conversation in an otherwise not very private setting.

Carrabba’s had changed its menu since we were last here.  The one dish they had before, Tag Pic Pak (seriously), was no longer on the menu.  It was Linda’s favorite dish and one of only two that we could eat.  They had something with a different name that the waitress said was the same but it included chicken.  She said they could leave the chicken out but the price would still be $14.95.  The Tag Pik Pak was $10.95 as I recall.  We have come to resent paying for animal products that we don’t eat.  Linda ended up getting whole grain spaghetti with Pomodoro sauce and I got whole grain spaghetti with olive oil and garlic.  Linda said the sauce lacked flavor.  My dish was “off menu” and was unimpressive.  Our salads, dressed with vinegar and oil, were OK and the bread was very tasty.  Linda had a glass of wine and I had blackberry sangria.  Sangria is Spanish, not Italian, but it was good.  The meal overall was disappointing but we had a great time chatting with Bruce and Linda over dinner.  The manager stopped by to ask how our meal was (as a courtesy) and ended up having to talk to us for 20 minutes.

Back home Linda made vegan banana nut muffins.  The organic bananas we bought at Meijer’s two days ago must have been bruised because they were going bad very quickly.  Banana bread or muffins was a great way to salvage what we could.  While she made the muffins I went to my office, checked e-mail, and off-loaded the photos we took today.

At 8 PM I turned on the Yaesu FTM-400 ham radio and participated in the SLAARC Info Net.  When the net was over I came back upstairs, reviewed the items in my B&H Photo shopping cart, and placed the order.  I then spent a little time researching DC distribution panels on the DX Engineering website and doing a Google search for cantilevered table supports and legs.  We each had a muffin for dessert and went to bed at 10 PM.  I put on the Detroit PBS Create channel, turned down the volume, and worked on this post for a while before finally going to sleep.

 

2015-10-18 (N) Homage to FLLW  

Leave a reply

We got up at 8 AM.  I made Ethiopian Yirgacheffe half-caffe coffee while Linda prepared vegan pancakes.  We had talked yesterday about going to the Howell Farmers Market this morning but did not feel like going out in the early morning chill.  When we finished our coffee I turned the fireplace off and we got dressed to work.

Our focus in the bus today continued to be the built-in sofa.  We decided yesterday to move the plywood seat out from the wall 4-3/4″ from its original position.  The original stationary board on the back side of the piano hinge, which was only 2-3/4″ wide, was designed to place the front edge of the plywood seat (which has a 3/4″ walnut hardwood edge) 3/4″ beyond the cabinetry on both ends of the sofa with an overhang of just a few inches beyond the vertical front support board.  It was a nice design which tied in well with the cabinetry and kept the sofa from intruding into the living room aisle.  It resulted, however, in a seating depth of 16″ which turned out to be too short.  It was my homage to Frank Lloyd Wright: integrated, attractive, cantilevered, and uncomfortable.

As much as I like and admire FLLW’s work, I also like the Bauhaus maxim “form follows function.”  We needed a 3/4″ thick (11/16″ actually) board 7-1/2″ wide by 77-7/8″ long to locate the plywood seat in its new position.  The only wood we had on hand that we could cut this from in one piece was a 24″ X 96″ piece of walnut veneered plywood.  Since the board will not be visible I did not want to waste the walnut veneered plywood for this piece.

We also had a half sheet (4′ X 4′) of good plywood and after thinking about it for a while I decided to make the stationary board in two pieces.  The key was that I would use a third piece, cut from that same 4′ X 4′ sheet, as a splicing plate to join the other two pieces together.  But I was trying to accomplish more than that.  With the original design the pivot line of the piano hinge was over the top of the wiring chase, about 1-3/4″ back from the front edge.  That meant the back edge of the moveable seat board, when closed, was resting on the wiring chase for its entire length.  With the new stationary board the pivot line of the piano hinge is unsupported except for 5-3/4″ on each end.  The third piece of plywood would be at least a partial solution to that problem.

We worked in the garage with the overhead doors closed and the furnace on.  I cut two 7-1/2″ wide pieces off of the 4′ X 4′ sheet of plywood and then cut them to lengths of 38-7/8″ each so they would be just shy of 77-7/8″ when butted together end-to-end.  We took the two pieces to the bus and set them in place on top of the writing chase which sits atop the HVAC duct.  They just fit, which was nice.  I marked the underside along the edge of the wiring chase with a pencil.   We then took the pieces back to the shop.

I found a relatively flat portion of the garage floor and laid the two pieces end-to-end face down.  I set the third piece on top of the first two so that it was of equal length in both directions from the center and was at least 1/4″ forward from the line I had marked.  This third board extended beyond the front edge of the other two boards by at least two inches along its entire length of four feet.  With Linda holding it in place I inserted four self-drilling wood screws, two for each of the main boards, to hold the three pieces in position.

We placed the old 2-3/4″ wide board along the edge of the new boards and marked the locations of all of screw holes for the piano hinge.  I then center punched and drilled countersunk holes for lots of screws being careful to keep them in between the hinge holes.  I ran all of the screws in until the points just protruded from the other side.  I then applied Titebond II wood glue to the two main boards, positioned the third board using the screw tips as alignment guides, and ran all of the screws down pulling the pieces tightly together.  Linda got a paper shop towel wet and I used it to clean off the excess glue that oozed out from between the boards.

We took the new stationary backboard to the bus and set it in place upside down.  I marked the underside along the edge of wiring chase and then we flipped it end-for-end and set it in place right side up.  We pulled it forward so I could mark the locations of the existing screws securing the top of the wiring chase to the two long sides and then slid it back against the wall.  The line served as my guide for where to screw the backboard to the wiring chase.  (The chase has two long “1×2″ sides on edge with a 3/8″ thick plywood top that is about 4-1/2″ wide.  For maximum strength I needed to screw through the backboard into the 1x2s.  I also needed to avoid the space between the 1x2s as that is where all of the AC wiring is run.)

I center tapped a lot of locations and drilled them with a #6 countersink bit even though I was using #8 self-drilling outdoor screws.  The reason for the drilling step was to make sure I did not split any wood.  I screwed the backboard to the wiring chase with lots of 1-1/4″ #8 screws in two rows corresponding to the front and back side boards of the wiring chase.

The backboard pieces had oozed a small amount of additional glue so I used a piece of scrap aluminum sheet metal to scrap it out of the joint.  When the plywood seat is closed the back couple of inches will rest on the third piece of plywood so there cannot be any interference along there.  We set the moveable seat board in place and marked all of the hinge holes on the stationary backboard and then pulled it out gain.  We did not, however, attach the piano hinge to the stationary backboard as I wanted to let the glue cure for at least 24 hours.

By this point it was 1 PM so we stopped to have lunch which consisted of vegan hotdogs with mustard, onions, and relish and both red and green grapes.  We got these grapes at Meijer’s and their produce is usually good, but the green grapes had almost no taste.  Oh well; there will be days (and foods) like that.

After lunch we shifted our attention to the driveway extension project.  I gathered up a box of plastic and wood stakes, a mallet, a 100 foot tape measure, and the site plan for the bus barn and driveway.  It took us about three hours to stake out the location of the pull-through driveway, locate the front corners of the bus barn, and stake out the approach/apron for the barn.  Phil will be back early tomorrow morning and the first thing on the agenda is going over the layout and figuring out elevations for the two planned level pad areas.

At this point Linda went inside to work on dinner while I cleared the margin of the woods along the south side of the driveway extension.  I added bar/chain oil and a 40:1 fuel:oil mixture to the chain saw and got out the compound loppers, pruning saw, pole saw, and safety glasses.  I initially used the loppers to cut down small saplings, cut off small branches, and trim back bushes and vines.  I used the chain saw to cut down slightly larger trees, up to 3” in diameter at the base, and finish cutting out three bushes and some entwined vines.  I then used the pole saw to trim low overhanging branches.  I dragged all of the cuttings to a spot on the west side of the fir trees and used the chain saw to cut the larger trees into smaller pieces.

It was 6:30 PM by the time I was done and had the tools put away.  Dinner was almost ready when I got a call from Butch.  He was following up on how our refrigerator was performing and also needed my assistance with a possible Ebay purchase.  The item he was interested in was in Canton, Michigan about 45 minutes from our house, and the seller was not willing to ship it.  He wanted to know if it would fit in our Honda Element and if so, would I be willing to pick it up if he decided to buy it.  Of course I was willing to help as long as my car was able to handle the item.  While he was on the phone I measured the clearance for the rear hatch and gave him the dimensions.  As soon as we got off the phone he e-mailed me the link to the auction, which still had 85 minutes remaining.

For dinner Linda started with a really nice salad that had slivered almonds and pumpkin seeds and dressed it with Ken’s Sweet Vidalia Onion dressing.  The main course was an amazing soup.  She roasted a golden acorn squash, sweet potatoes, carrots, garlic, and shallots.  She then put these in a pot, added vegetable broth, and heated the mixture.  To finish the dish she used an immersion blender to purée everything into a smooth, thick, hearty, and delicious soup.  After working outside all afternoon on a chilly day it really hit the spot.  We finished the bottle of Cupcake Black Forest red wine we opened yesterday.

After dinner I retrieved Butch’s e-mail, checked out the item, and e-mailed him back.  I then spent a little time reading and replying to posts in various RVillage groups.  I called Butch back just before 8 PM and then turned on the Yaesu FTM-400 to join the SLAARC Info Net at 8 PM.  Unfortunately all I heard was noise.  I have not used the radio for the last few weeks so I don’t know if the net did not take place (unlikely but possible) or if a problem has developed with our system.  If the later, it is most likely the Morgan I.C.E. lightning arrestor (again).  Whatever the reason, I was not going to figure it out this evening.  I went to bed at 9 PM and wrote this post.  It took some time to write but if I do not record the details the same day they slip away quickly.

 

2015/08/30 (N) A Day of Rest (NOT)

Leave a reply

We had closed up the house and turned on the air-conditioning before going to bed last night and had it set at 72 degrees F to make sure it ran long enough to pull some of the humidity out of the air.  I awoke at 7:30 AM on this penultimate day of August hoping to be able to open up the house, which Linda prefers in almost any weather, but was greeted with fog and temperatures in the mid-60’s so I turned the A-C back to 70 to make it run for a while and move the air around.

Sunday is supposed to be a day of rest but not for us, at least not today.  I gathered up the laundry and started a load in the washing machine and was just starting to prepare our morning coffee, Kenya AA (not decaf), when Linda emerged.  She washed off some fresh blueberries and got our granola ready.  We were both dressed to work but enjoyed our coffee in the living room from 8:30 until 9 AM.

Our first bus project task was to trim the passenger side front piece of underlayment that we cut last night.  With that done I rolled the air-compressor out by the entrance door, uncoiled the air hose and connected it, unrolled the extension cord and plugged it in, oiled the air stapler, and connected it to the air hose.  I loaded the staples and, with Linda standing on the pieces to hold them flat, stapled them down.

The next piece of underlayment, which would finish the hallway, was a very tricky piece with lots of angles.  The problem in measuring a piece like this, in which sides may not be exactly parallel and angles not exactly 45 degrees, is finding a reference corner with two factory edges from which to measure everything.  I take the time to make and check the measurements by making a small, approximately to scale, drawing.

The cutting of these pieces involved a 7-1/4″ circular saw and a saber saw.  When using the circular saw we usually clamp a saw guide to the panel, allowing us to get a clean, straight cut that is almost as good as a table saw.  For shorter cuts on edges that will not abut other panels I use the saber saw without a guide and just follow the pencil line as carefully as my skill and eyesight allow.  I also have to use the saber saw for blind stop cuts, such as notches and tabs.

We took a break to have PB&J on whole grain bread and fresh apple slices for lunch.  As we were finishing lunch I exchanged TXT messages with Chuck.  He wanted to chat and called about 5 minutes later.  It turns out that he has an air suspension seat base and thought I might want it.  After getting a better understanding of what it is, and isn’t, I agreed that I wanted to see it.  It would be very cool if I could use it to replace the driver seat pedestal in the bus as part of putting in the new Flexsteel seat but I will have to check with Josh to see if that is possible.

The bathroom underlayment was next.  We considered various ways to install it and came to the conclusion that it would take three separate pieces for this small space.  The reason was deep toe kick spaces on opposing walls, angles and notches, and a drain pipe and water supply pipe for the toilet that project out at least eight inches from a third wall just an inch above the floor.  Those features made it impossible to get a single piece installed.  We might have done it in two pieces but I did not like the way I would have had to cut them.  These three pieces took quite a while to lay out, cut, trim, and staple down.

The bedroom was the next/last piece of the main floor jigsaw puzzle.  It was after 6 PM by this point.  We knew we would not get the bedroom done today but decided to try and get one more piece installed.  Most of the bedroom floor is taken up by the storage box that serves as the base for the plywood bed platform.  This box goes all the way to the driver side wall and has small Isles on the other three sides.  If not for end cabinets by the head of the bed and deep toe kick spaces in the cabinetry to the rear of the coach the underlayment would be a simple “U” shape.  The actuality it will take four pieces to complete this space.

The first piece was a simple shape, a rectangle with a large piece of one corner cut out.  As I have for every other piece I took the initial measurements but noted them on a freehand sketch rather than a scale drawing.  When I laid out the actual panel the numbers were not quite working out so I rechecked my measurements.  They appeared to be correct, which meant some of the right angles must be off slightly.  I modified the layout to make the panel a little longer than I thought it needed to be and made the cuts.  Inside the coach we were not able to get the panel positioned because of interference from a 4″ round HVAC duct and a door and handle on a lower cabinet (the end table).  I removed the HVAC register, which helped and then discovered a piece of vertical trim in the passenger side front corner.  The bedroom has less natural and artificial lighting than the rest of the coach and I had not noticed it before now.

Tired and a bit frustrated by this latest turn of events we decided to wrap up our work for the day and have dinner.  We accomplished a lot today but I had hoped (expected) to have all of the main floor underlayment done.  We will finish the bedroom first thing tomorrow.  That will leave only the entryway/cockpit to do and we will defer that work so I can start laying the new tile floor.

While Linda prepared dinner I checked my e-mail and then checked in to the South Lyon Area Amateur Radio Club information net at 8 PM.  I was just completing my second turn when Linda called me to dinner.  She made her own version of red beans and rice and served it with a glass of Cupcake Black Forest Decadent Red wine and a large piece of honeydew melon on the side.  The main dish was excellent, the wine was OK (a little dry for me), and the melon was not as ripe as we would have liked it to be.  Still, it was a nice meal.

We watched an episode (rerun) of Sherlock at 9 PM and then went to bed.  Linda played Scrabble while I worked on this post before falling asleep.

 

2015/08/16 (N) A Send Off For Katie

Leave a reply

We had a light breakfast and enjoyed our morning coffee.  With company due at noon we were not inclined to do any overly physical work this morning.  Linda made a quick run to the supermarket and then spent the late morning finishing food preparations.  I worked in my office installing operating system updates, updating the BCM page on our website, and editing/uploading blog posts.

Our step-granddaughter, Katie Bortz, is leaving for college in a few days so Linda arranged to have her over for lunch along with our daughter, Meghan, and son-in-law, Chris (Katie’s dad).  They arrived around noon and stayed until almost 5 PM, a longer visit than usual.  For lunch we had chickpea salad, corn-on-the-cob, collard greens cole slaw, and potato salad.  Meghan made two desserts at home and brought them: cheesecake and vegan oatmeal bars.

Grand-daughter Katie (L) waiting for a slice of cake baked by her step-mom (our daughter, Meghan, on right).

Grand-daughter Katie (L) waiting for a slice of cake baked by her step-mom (our daughter, Meghan, on right).

Katie got a head start on college while still in high school and took several AP classes.  She also tested out of some basic classes so she will hit the ground running with at least some courses that are directly related to her interests (biology, specifically animals), and major (wildlife and fisheries).  She will be moving into one of the dorms and paired up with another freshman girl during orientation.  They have the room arrangement worked out, at least on paper, and I expect that everything will fall into place.

For dinner we had leftovers from yesterday’s meal after which I chatted with Chuck for a while on the phone about refrigerators in buses.  I worked on blog posts after that and was going to participate in the SLAARC info net at 8 PM.  Linda noticed that there was a program about the Real Scotland Yard on Lansing PBS at that time, followed by an episode (rerun) of Sherlock.  Harvey (AC8NO) was the net control operator for the info net and as soon as he called for check-ins I did an “in and out.”  Once he acknowledged that he had received my check-in I settled in to watch the programs.  After that it was off to bed to play a few iPad games before going to sleep.

 

2015/07/26 (N) Rearranging

Leave a reply

I was up at 8 AM but did not make coffee as Linda was still asleep and the grinder is fairly noisy.  I put the last load of laundry in the washing machine, cleaned the litter tray (which we keep in the downstairs shower), and then worked in my office.  Jasper (the cat) came down to assist me but mostly ended up supervising.

All three monitors mounted in the ham shack using the ZioTek wall-mounted track system. The Dell is in the middle. There is a mount and room for one more monitor at the right end.

All three monitors mounted in the ham shack using the ZioTek wall-mounted track system. The Dell is in the middle. There is a mount and room for one more monitor at the right end.

I mounted the fourth (last) arm on the wall-mounted rail in our ham shack.  I swung it back against the wall to get it out of the way as I do not have a monitor that I want to install at that position at the moment.  I cleaned up the tools and staged them by the stairs and then moved the coiled coax out of the way and cleared a few things off of the desks so I could move the desks back into position.  I left them farther out from the wall than before so they were appropriately placed relative to the three wall-mounted monitors.  I then put various pieces of ham radio equipment back on the desks.

Monitors obviously need computers.  I removed the Dell Precision laptop from my computer desks, removed the computer from the combination docking station and monitor stand, cleaned all of the pieces, and reassembled it.  I set it at the left edge of the ham desks, slid it under the left monitor, and placed our old Icom IC-706 HF transceiver on the monitor platform, just for appearance sake.  We are not using thus radio at the moment but it fit nicely in that spot.

I placed the GoBox with the Icom IC-7000 HF/VHF/UHF transceiver and 12VDC power supply at the right edge of the desks, put the MFJ-998 Intelli-Tuner to its left (under the right monitor), and put the larger variable voltage DC power supply on top of it.  The time we spent yesterday determining where to mount the rail on the wall was time well spent.  The monitors are at a comfortable height for viewing when seated at the desk, tilted down slightly to avoid glare from the overhead down lights, and the bottom edges are high enough above the desk to permit sizeable equipment to slide under them.  The desks are also far enough out from the wall to make it easy to attach and manage cables.

I rearranged my primary ASUS laptop on my computer desks and checked my e-mail accounts.  I have had a discussion going on this past week with Gary at Bus Conversion Magazine about hats with the BCM logo and responded to a couple more of those communiques.  Around 10:15 AM I heard footsteps and knew that Linda was finally up so I wrapped up the work in my office, transferred the laundry to the dryer, and went upstairs.

Linda was working at her desk and was not hungry but wanted coffee.  She did not sleep well last night so I made a pot of Sumatra Manhelding which is NOT one of our half decaffeinated blends.  I got myself a bowl of granola and had a large glass of orange juice.  We spent the rest of the morning in the living room reading, writing, and menu planning.

The dinette area of our bus with the two fan-coil heat exchangers on the floor. They will go in the bases of the desk when it is installed in this corner.

The dinette area of our bus with the two fan-coil heat exchangers on the floor. They will go in the bases of the desk when it is installed in this corner.

I like to hear the grandfather clock strike 12.   Besides the charming Westminster chimes, it serves to announce that the part of the day has arrived where I am supposed to get some of the physical work on my to-do list accomplished.  Today, however, my #1 priority was to redesign the pull-out pantry so I limited my physical work to gathering up my tools from the basement and moving them to the garage, moving the bus back to its normal parking spot, and taking photos of cabinet details in the bus for Jarel.  I mixed in a little e-mail, a few computer updates, some ham radio, and time for meals, but basically I worked at my drafting board most of the day and evening.

For dinner Linda made a very tasty dish that we had not had before.  The base ingredient was rice and she used basmati even though the recipe called for brown.  I prefer basmati rice to brown rice so it was a good substitution as far as I was concerned.  The other ingredients were garlic, power greens, mushrooms, and blanched fresh green beans.  She sliced and caramelized a large onion and used it as a topping.  This was essentially a “1-pot” dish in that all of the ingredients ended up combined prior to serving.  Linda makes a lot of dishes like this and we both like them. This particular dish had the crunch of the green beans, the chewiness of the rice, and the soft earthy character of the mushrooms held together by the garlic and olive oil and topped with sweet earthiness of the caramelized onions.

At 8 PM local (EDT) I participated in the weekly SLAARC Info Net for the first time in a couple of years and did so from the comfort of our ham shack.  It was a pleasure using our new Yaesu FTM-400DR/DE dual band transceiver with our Diamond X-50N 2m/70cm antenna at a height of 40 feet and connected by good coaxial cables all the way through.  Club president Harvey (AC8NO) served as net control operator and did a nice job.

After the net wrapped up at 8:45 PM Steve (N8AR), Andy (N8DEV), and I chatted for another 20 minutes trying to find some rhyme or reason why our Yaesu FTM-400’s are experiencing random audio dropouts.  We did not get it figured out and wrapped up our QSO so Steve and I could check into the LARK (Livingston Amateur Radio Klub) net that started at 9 PM (EDT).  This was the first time I had checked in to this particular net even though LARK is based in Howell and the repeater is closer to us than the ones in South Lyon or Novi.

The LARK Net was much briefer than the SLAARC net and concluded at 9:16 EDT.  Steve and I went back to the South Lyon repeater where Paul (N8BHT) heard us and joined the conversation.  When we finally wrapped up our testing QSO I went back to work on my pull-out pantry drawings.  I was about to shut everything down at 10:45 PM EDT when Mike (W8XH) announced his presence on the South Lyon repeater.  He was mobile but full-quieting and I did not experience any dropouts during our 25 minute QSO.  I took a few minutes to e-mail Jarel and then called it a night.  I had a few almonds as a snack, got ready for bed, and worked on this bog post for a while.

 

2015/07/05 (N) Return to HFM

Leave a reply
Madeline helps Grandma Linda mix the batter for vegan blueberry pancakes.

Madeline helps Grandma Linda mix the batter for vegan blueberry pancakes.

The day started with Grandma Linda’s fabulous, made from scratch, blueberry vegan pancakes for breakfast, which Madeline helped make!  After breakfast we took Madeline to the Howell Farmers Market (HFM).  She had been to this market with us once before and it was a beautiful Michigan summer morning for a return visit.  On the drive over we discussed why it is that you cannot buy a farmer at a farmers market and you cannot buy a garage at a garage sale.  English can be a funny/strange language.

We walked the entire market, which is not really that big, and Linda bought some fresh strawberries.  A couple of the regular vendors were missing.  In particular we wanted to buy some more soap from Marjorie but she was not there.  Madeline enjoyed checking out the child and doll sized wooden furniture that one vendor had for sale.  We kept an eye out for someone selling jelly beans but did not see any so we stopped at the CVS on the way home and got a small bag of them.

We had just gotten home and I was unlocking the front door when Brendan and Shawna arrived.  We had a nice visit and they stayed for a light lunch.  By the end of lunch Madeline was showing signs of being ready for her nap so Brendan transferred the car seat and stroller from Linda’s car to their car, gathered up all of Madeline’s things, and loaded their car.  Madeline left with her parents at 12:30 PM and Linda laid down for a nap shortly thereafter.

I looked at the SLAARC WordPress website on my iPad to make sure it was working.  I checked most of the pages except for the Member Only Area, which requires a login, and they appeared to be OK.  I then went to my office to deal with things that needed to be dealt with from there.

Madeline tries on a child sized rocking chair at the Howell Farmers Market.

Madeline tries on a child sized rocking chair at the Howell Farmers Market.

My first task was to update the roster and financial records for our FMCA Freethinkers Associate Chapter.  I sent e-mails to new members, uploaded the updated roster to our Dropbox, and e-mailed everyone that they were available.  I had received the draft copy of the June 2015 issue of Bus Conversion Magazine on Friday.  I proofread part 3 of my 4-part article on the exterior renovation of our motorcoach and sent corrections to the editor.  I then settled in to edit blog posts.

I took a break for dinner.  Linda cooked Brussels sprouts and heated some vegan riblets.  The barbecue sauce on these riblets is very tasty.  We had vegan chocolate cupcakes for dessert and they were very tasty too.  I then went back to my office and continued editing blog posts.

I took a break just before 8 PM to join the South Lyon 2m Information Net using our new Yaesu FTM-400DR/DE RADIO but I did not hear anything except noise.  I left the radio on for a while and then turned it off.  I switched the coax to the Icom IC-7000 and turned it on but did not hear anything there either.  I turned the IC-7000 off, switched the coax back to the FTM-400, turned it back on, and went back to work at my desk.  Around 8:30 PM the squelch started opening and I heard very faint voices way down in the noise.  After listening carefully I was able to determine that it was Steve (N8AR) running the net but I could not understand most of what was being said.

It was the first time in a long time that I had tried to participate in the net and I was disappointed that the new installation of the antenna on the tower and coax cables to the radios in the basement was not working adequately.  They were working OK when I tested them with Mike (W8XH) so it could have been an unusual band condition but Steve was obviously getting in from farther to the west than our QTH.  I enjoy operating and am looking forward to finally having our larger tower up and some HF antennas in operation but for now I need to concentrate on getting the VHF/UHF stuff working reliably (correctly and consistently).

I exchanged some e-mails with Gary at BCM regarding the magazine and then continued editing blog posts.  I got through the end of June by 11 PM and quit for the night.