Tag Archives: Ron & Mary (PA)

2016/01/21 (R) – 2016/01-25 (M) East and South

2016/01/21 (R) Lake Okeechobee

The weather forecast for today was for very nice conditions and we thought it would be a nice day to go for a ride in the car and explore the area of the state to our east, specifically Lake Okeechobee.  We were up a bit earlier than has been typical for us lately and did not make breakfast or coffee in favor of getting an early start.

The Defraggler disk defragmenter had finally completed its task.  I restarted my computer but it was not behaving correctly.  Besides the disk check and defrag I had also updated the NVIDIA graphics card driver, installed operating system updates, and updated Skype, which configured itself to auto-start on initial boot up.  I had to restart my machine again and suggested to Linda that we drive to the Shell station to top up the rank and then get coffee and bagels at the Dunkin Donuts next door.  I stopped back at our coach to check my e-mail and then shut my computer down.  I was looking for an e-mail from Herb, a member of the FMCA National Education Committee, about his visit to Lakeland, Florida today but he had not replied.  It was a long shot whether we would get to Lakeland today anyway.

We headed east on FL-70 as far as US-27 and then headed south towards Moore Haven and Clewiston.  Most of the drive was through the citrus groves, ranch lands, and fields of crops that make up most of this part of Florida.  The citrus groves eventually gave way to a tall plant with a wheat-like top that we did not recognize but thought might be wheat.  We passed a couple of fields that had been cleared and the organic matter mounded into burn piles.  When we saw large plumes of smoke later in our drive we assumed it was related to more land clearing.  Only later did Linda determine that the plants were sugar cane and the smoke was most likely from controlled burns of the cane fields which is the first step in harvesting the sugar cane.

We had not done a lot of research on Lake Okeechobee and the surrounding area.  What we did know was that it is the largest fresh water lake in the U. S. contained entirely within the borders of a single state.  What we did not know until we saw it was that the entire lake is surrounded by the Herbert Hoover Dike, a massive levy some 50 feet high with flood control gates and canals leading from it.  Construction was begun late in Herbert Hoover’s presidency as a result of a hurricane that pushed an enormous amount of water out of the lake to the southeast and killed thousands of people.

The first place on our drive where we were near the lakeshore was in Moore Haven but as a consequence of the dike there are only a few places where you can actually see the lake.  From Moore Haven to Clewiston US-27 ran right along the levy and we could see nesting boxes on top of tall poles.  All of them had nests and most of them had large birds roosting on them.  I presumed they were probably Osprey or possibly Eagles.

The first place we stopped was a county campground at South Bay, a small community at the southwest tip of the lake.  We were able to drive over the levy to a boat launch area, but the western and southwestern portions of the lake have extensive marshes and we could not see open water even from the top of the levy.  We also drove through the campground, which impressed us as a nice place to spend a couple of weeks to a month, depending on what else there was to do in the area.

We continued around the south end of the lake to Belle Grade, picking up US-441 to Pahokee where we drove over the dike to a marina that was part of a state park with an RV campground.  Before us was the lake and, like looking at a Great Lake or an ocean, it was indeed an endless expanse of water to the horizon.  Okeechobee is a big lake.

From Pahokee we continued up US-441 through Canal Point and along the edge of the levy up to the town of Okeechobee.  This stretch of highway was lined with RV parks, most of them small and not very nice looking.  We weren’t counting but I estimated somewhere between 18 and 24 “parks,” one right after another.  Many of them were full of old, closely spaced, rigs that appeared to be in very poor condition that was matched by the run down, trashy appearance of the properties themselves.

There were a few parks that looked OK and one of them was a park that Linda had called to inquire about openings and rates.  We always check out websites, Google Maps, and Google Earth, but they don’t always reveal the true appearance of a place or surrounding area.  Now that we were seeing this area first hand we were glad (relieved?) that we did not book a spot here.  At the risk of appearing snobbish, the east side of Lake Okeechobee did not impress us as a place we would stay or even need to visit again.  That said, we understand that everyone’s circumstances are different and folks do the best they can.

Yes, we own a Prevost bus conversion, but we bought it very used and we do not think of ourselves as “those” kind of people; you know, snobbish towards those who own SOBs (some other brand).  But we are aware that we have a fairly negative reaction to places that are trashy.  Trashy and old are not the same thing; we have nothing against old.  We are old ourselves, and hope to get a lot older before our time is up.  Trashy suggests a lack of self-respect and a lack of respect for others.  We will take a pass on that.

By the time we reached the town of Okeechobee it was 2 PM and we were hungry.  Rather than continue on to Sebring we headed west on FL-70 where we found a Subway just before reaching the edge of town and stopped to have lunch.  After our meal we headed back to Arcadia 63 miles away on FL-70.  Along the way we saw more Osprey near the Kissimmee River and later on a group of Wood Storks and a few Sandhill Cranes along with the usual Egrets, Vultures, a Kingfisher, and other local birds.  Florida really is a great state for seeing birds.

Once we got back to our coach we relaxed for a while and then decided to go to the jam session at 7 PM.  The jam sessions here are different from what we have experienced other places.  We found out from talking to the attendees sitting around us that the four musicians (two guitars, bass guitar, and drums) are not from the park and are brought in (hired) for the jams.  People from the park took turns singing but no other musicians joined in during the hour we were there.  There were also a lot of people dancing, including singles and couples line dancing.  We left just before 8 PM and returned to our coach to watch our Thursday evening TV programs.

Another major storm was winding up across the south and taking aim on the mid-Atlantic and New England.  The worst effects of this storm were forecast to be ice and snow accumulations of 12″ to 36″ from northern Georgia north and east to the Canadian Maritimes.  As with the last few storms the impact on Florida was forecast to be strong storms associated a quickly moving cold front draped off of the low pressure system and extending far into the Gulf of Mexico.  Rain was expected in Arcadia starting around 4:30 AM.  Several bands were expected, with the strongest from late morning to early afternoon.  Behind the front would be strong winds and much cooler temperatures.  We left the awning style windows open an inch, closed the roof vents, and went to bed.

Linda at the shore of Lake Okeechobee, FL.

Linda at the shore of Lake Okeechobee, FL.

2016/01/22 (F) Desoto Veterinary Clinic

Heavy rain moved through our location starting at 4:30 AM, exactly when the weather forecasts said it would.  It arrived along with some wind and woke me up but it was not severe and I eventually fell back asleep.  The cats had their usual morning crazies starting around 5:30 AM so that woke me up again, and probably woke Linda up too, but they eventually calmed down and we all went back to sleep.

We finally got up at 8:15 AM and Linda got dressed right away.  It was cool enough that I put on my sweats but not cold enough to run the toe-kick heaters or the hydronic heating system.  I made our morning coffee and we had Linda’s yummy homemade granola with fresh blueberries for breakfast.  I got dressed after breakfast and at 9:45 AM we put Jasper in his carrier and drove to the Desoto Veterinary Clinic for his 10 AM appointment.  There was a lull in the rain with the heaviest, potentially severe, weather expected between late morning and early afternoon so we got to the clinic and back without getting rained on.

We only had to wait a few minutes while Dr. McNulty finished up with another patient.  Jasper rarely goes in his carrier at the house or on the bus, even though we leave it out and accessible, but tends to stay in it at the vet’s office.  Dr. McNulty was a bit of an eccentric character but we liked him.  He spent as much time talking to Jasper as he did to us and checked him over to make sure he did not have other undetected health issues.  His diagnosis of Jasper’s fur loss was that he had been bitten by a flea.  He recommended a small corticosteroid injection to help relieve the itching and reduce Jasper’s need to scratch.  He also suggested that we discontinue the use of the Revolution medication while we are in Florida and switch both cats to Cheristin.  We agreed to all of his recommendations.

Unlike Revolution, which also prevents heartworm, Cheristin is a flea medication only.  Even though Florida is the flea and mosquito capitol of the U. S. Dr. McNulty said that heartworm, acquired from infected mosquitos, is extremely rare here while cats being affected by fleas is quite common.  His concern with Revolution is that the fleas have become resistant to it.  He quit prescribing Frontline and Advantage years ago and has now stopped prescribing Revolution for the same reason.  Jasper and Juniper are strictly inside cats so their exposure to mosquitos, fleas, and ticks is minimal as those critters can only gain entry to the coach via the front door when it’s open or hitch a ride in with one of us.  Still, they do not live in a hermetically sealed environment.

The rains resumed around 11 AM.  Linda complied a grocery list while I worked at my computer on some e-mails and did a little additional work on photos for my featured bus article on Ronnie and Diann Mewbourn’s 1969 Model 07 Eagle bus conversion.  We had hummus and onion sandwiches for lunch around 12:30.  Linda waited for the rain to subside and finally headed to the local Winn-Dixie supermarket around 1:15 PM.

I had not worked on blog posts yesterday so I finished up the one from the 20th and worked on the ones for yesterday and today.  When Linda got back I helped get the groceries up into the coach.  I off-loaded the photos I took yesterday but was tired and did not feel like getting deeply into any computer-based work.  I laid down on the sofa instead and took a nap.  I like naps; naps are good.  While I was napping Linda went for a long walk.  I finally woke up as she was starting to prepare dinner.  The preparations were going to take a while so I went for a walk.

Dinner was butternut squash burritos and Mexican rice and was very tasty.  After dinner Linda applied the Cheristin to both cats.

PBS had back-to-back episodes of Endeavour, the series detailing the beginning of the career of the Inspector Morse character.  Linda slept through most of the second episode and went to bed as soon as it was over.  I stayed up and watched a show about the Neon Sign Museum in Las Vegas and two companies that are each restoring a sign for the museum.  I watched the weather for a few minutes and then went to bed.

An Anhinga dries its wings along the shore of Lake Okeechobee, FL.

An Anhinga dries its wings along the shore of Lake Okeechobee, FL.

2016/01/23 (S) Pelican Lake

It was a wild day today, wind wise.  Sustained winds of 25 to 35 MPH, with gusts 10 to 15 MPH higher than that, swept across southwest Florida behind the cold front that brought yesterday’s rain.  And it was a cold air mass, with temperatures this morning in the low 40’s F.  After getting up and putting on our sweats, which is what we do on chilly mornings, I made a pot of coffee, which is what I do almost every morning.  Linda decided it was a good morning for pancakes.  Vegan baking can be a bit tricky, but they turned out really well.

We did not have any plans for today.  We had thought about attending the Fort Myers RV Show, at the Lee County Expo Center on FL-31, but decided there would not be anything new to see after having been to the Tampa RV Supershow the previous weekend.

After breakfast I called Chuck to catch up on things generally, discuss leaky windshields in particular, and see if we could arrange a time to visit.  While we were talking a gust of wind opened our patio awning about 12″ and then let it slam shut.  I realized immediately that I had not latched the roller tube at either end when we retracted it a few days ago in advance of the latest round of storms.  I told Chuck I would call him right back and went outside to latch the tubes.  We always latch the roller tube when stowing it prior to moving the coach so I found it to be an interesting oversight on our part that we had not done this when stowing it while stationary.  We were lucky that we were home when this happened and that I was seated where I could see exactly what had happened and quickly figure out why.  You can be sure we will latch the roller tube from now on whenever it is retracted.

With yet another problem diagnosed and fixed I called Chuck back.  As it turned out there was also an RV show taking place at their motorcoach resort this weekend; mostly new and used Prevost conversions from Millennium, Marathon, Liberty, and Featherlight, with a few others and some high end motorhomes thrown in for good measure.  The show was open until 4 PM and Chuck was doing volunteer shuttle service with his golf cart from 2 – 4 PM.  It was a nice day, except for the wind, and we decided to drive down for a visit, look at some of the coaches, and then go out to dinner.

We left around 11:30 AM and stopped at the Shell station to top up the fuel tank.  We then headed down FL-31 to its terminus at FL-80 and headed west for a few miles where we picked up I-75 southbound.  We exited I-75 at exit 101 and drove another nine miles on Collier Blvd, finally crossing Tamiami Trail (US-41) before arriving at Pelican Lake Luxury Motorcoach Resort.  While we were stopped at the light at Tamiami Trail Linda called Chuck as requested.  When we got to the resort entrance he and Barbara were waiting for us in their golf cart.  Rather than parking with the other RV show attendees they led us back to their site and let us park there.  By the time we got to their site it was approaching 1:30 PM.  They gave us a tour and we sat outside in the sun chatting, their extensive landscaping sheltering us from most of the wind, which had blown us around on the drive down and was still blowing strongly.

At 2 PM Barbara took their car and headed to the grocery store and Chuck drove us to the coach display area in his golf cart.  While he performed his volunteer service we looked at all of the Prevost conversions but did not bother with the motorhomes other than the Newells.  The only coach we saw that would have tempted us to trade in our Royale Coach was a Featherlight that was done in walnut laminate (not real wood) with light wall and ceiling treatments and no mirrors on the ceiling.  It had a light, clean, modern feeling that appealed to us.  Being new, it was in better condition than ours and had a much newer technology Volvo 4-cycle engine.  It was also way out our price range, even if they gave us what we had invested in our coach in trade-in value.  New Prevost conversions are very expensive toys.

We did pay attention, however, to the induction cooktops that most of the coaches had and took pictures of the name plates for future reference.  Replacing our Gaggenau halogen cooktop with an induction unit is high on our list of future upgrades.  Ideally it will be a 120 VAC unit so we can use it on a 120 VAC / 30 Amp electrical service.  At least now we have some things to check out.

A few minutes before 4 PM we walked back to Chuck and Barbara’s site.  I paused long the way to take a few pictures as the resort really is visually stunning.  We sat at their patio table and enjoyed the setting in the late afternoon sun.  Chuck eventually called me on my cell phone to let me know he was done with his volunteer service and find out where we were so he could drive us back.  He was surprised we had walked, but then we are always amazed that people use their golf carts for short trips.

When Chuck returned we went inside to chat and he opened a bottle of Santos Sparkling Moscato (white).  Wow, that was a nice cocktail wine!  The buy it at Costco so that may finally be the reason we need to join.  Barbara returned with the groceries and after putting them away we had a second glass of wine.  After some research and discussion we determined that The Loving Hut restaurant, on the north side of downtown Naples, was, in fact, still open for business and was acceptable to all four of us.  The restaurant is just off of Tamiami Trail, so easy enough to find, but traffic in the Naples area is heavy all the time and it took a while to get there.  Once we arrived we settled in for a long meal with good conversation.

There are three things we like about The Loving Hut restaurants, not in any particular order.  For one, the menu is essentially Chinese and SE Asian cuisine.  Second, the menu is extensive with page after page of dishes to choose from.  Third, the entire menu is vegan; we can, literally, pick dishes at random and know that we can eat them and that we will like them.  As a bonus, they also have a nice assortment of European style vegan desserts.  It’s a chain, and we really wish we had one of these near our house, but it’s probably just as well that we do not.

We drove separate cars to the restaurant since it was in the direction we needed to go and neither of us had a car that would seat more than two people.  We said “farewell until next time” in the parking lot at 8:15 PM and headed our separate ways.  We only had a few miles to travel to the east to get back to I-75.  From there we retraced our route and finally arrived back at our coach around 9:40 PM.

We had left the windows cracked so it did not too hot inside for the cats but by the time we returned it was 66 degrees inside.  Not freezing cold, to be sure, but just chilly enough to warrant the application of heat for a while.  We changed into our sweats and watched some old British comedy programs on PBS/Create as there was nothing else on that looked interesting and I was too tired to start working on anything, including this post (which I deferred until Sunday).  I shut off the hydronic heating system and the electric toe-kick heaters, and turned on the electric heating pad on my side of the bed, before turning in for the night.  Juniper (our female cat) very quickly got under the covers between us and spent the rest of the night there.  Jasper (our male cat) alternated between our pillows and the foot of the bed but never got under the covers.  Juniper likes the warmth and security but I think it’s too hot for Jasper and makes him feel trapped.

Barb and Chuck’s site and coach at Pelican Lake, Naples, FL.

Barb and Chuck’s site and coach at Pelican Lake, Naples, FL.

2016/01/24 (N) Snowmagedon Exchange Rate

We woke to an outside air temperature of 38 degrees F, our coldest morning yet since we arrived in Florida, but we were not complaining.  We closed all of the windows before going to bed last night and the temperature only dropped to 59 degrees F in the coach, which is actually a nice temperature for sleeping.  We put on our sweats and turned on the three thermostats that control the zone pumps and fan-coil heat exchangers for the Aqua-Hot hydronic heating system, along with the front electric toe-kick heater.  The Aqua-Hot diesel burner was still “on” from yesterday when we showered but the electric heating element kept it from running so I turned the element off.

The strong, sustained winds yesterday had caused no more damage than a temporary power outage while we away from the coach, for which our house battery/inverter system took over as it is supposed to do.  Our weather related problems were few by comparison to what others’ experienced.  Just 200 miles north of us it was 28 degrees F in Williston and colder still Nashville, Tennessee with a low in the mid-teens.  Temperatures back home where around 20 degrees F, but that’s typical for SE Michigan this time of year, perhaps even a bit on the warm side of normal.

By far the worst weather, however, was the major snow/ice/wind storm that affected a large area from NW Mississippi up to Ohio and east across Georgia, Tennessee, Kentucky, and Pennsylvania to the eastern seaboard from Georgia, through the Carolinas, Washington D. C., Philadelphia, New York City, and on into New England.  Harrisburg, Pennsylvania, just west of Hershey and Annville, where Ron and Mary live, got 28″ of snow, and a small town in West Virginia got 40.5″, while places along the coast experienced significant flooding.  Thousands of flights were cancelled and transportation in D. C. and New York was at a standstill.  All things considered we felt like Arcadia was a really good choice for our winter base this year.

Linda checked in with Ron and Mary and they reported 30″ of snow at their house which they were in the process of clearing from their driveway.  Linda also checked in with Meghan, who reported no serious weather back home.  More importantly their male cat, Inches, had finished his round of medication and was doing much better.

Having visited Pelican Lake yesterday we were thinking about where we might go when we leave Big Tree RV Resort at the end of the first week in March.  Our thoughts drifted back to the conversation we had at the Tampa RV Supershow with the representatives from Florida Grande Motorcoach Resort.  Like Pelican Lake, Florida Grande is an ownership park.  It’s located near Webster, Florida about 100 miles north of Arcadia and a similar distance southeast of Williston.  The prices for lots there are more in our price range than Pelican Lake but we are a long way from buying an RV site anywhere.

Linda checked the website and saw that Florida Grande was offering a 2-for-1 special at the moment; pay for one week at the regular price (~$267) and get a second week free.  It also appeared that they had openings for the second and third week of March.  We were thinking of stopping there for a few days to check it out on our way to the FMCA national rally the third week of March in Perry, Georgia.  We have been reconsidering our attendance at that rally, however, as we really do not want to be that far north that early in March.  The 2-for-1 deal now has us thinking that Florida Grande might be a good place to spend the second and third weeks of March and then try to get into Jetty Park at Cape Canaveral for the last week of the month.

Linda took over the desk to work on some things for the bakery so I spent the late morning writing my blog post for yesterday and starting today’s post.  The high temperature today only reached 59 degrees but that was plenty warm enough to dump the holding tanks and refill the fresh water tank, which are on the sunny, southeast facing side of the coach.  Before I even got started, however, I ended up in a conversation with Dave whose 5th wheel trailer is across the street from us.  He and Barb are from New Hampshire and this is their 8th season at Big Tree RV Resort.

Dave said that the resort residents used to be about 60% from Quebec Province but the number has dropped to about 30% in recent years.  Most people “age out” of this lifestyle, whether mobile or stationary, due to declining health, strain on their financial resources, or loss of interest.  In the case of the folks from Quebec (and Ontario) the exchange rate to the U. S. dollar, which is currently 60%, is making it prohibitively expense for them to come south of the border for the winter.  When they exchange $1,000 CA they get $600 US.  That makes it really tough to come here and is one of the reasons our friends, Bill and Karen Gerrie, did not return to Florida, or anywhere else in the U. S., this winter.

All of the park models and permanent trailers here at Big Tree Carefree RV Resort are owned by individuals, not the park, so beyond the nice climate and social connections the owners have a real monetary investment here.  Dave said that 17 to 24 units are typically for sale each year but so far people are buying them.  The largest contingent in the park now appears to be Michiganders (aka Michiganians). One of the couples we were talking to at the jam session on Thursday was from Jackson, Michigan and told me that in recent years they have been getting 75 attendees at the Michigan dinner, and that is probably not everyone in the park who calls Michigan home.

While I was out talking to Dave and tending to our tanks I took a closer look at our new windshield and discovered that the caulk the Safelite installers used was coming loose from everything, i.e., it was not adhering to the glass, the rubber gasket, or the body.  Chuck has had the same issue with his two windshields and has a “claim” in progress with Safelite.  He had e-mailed me all of his correspondence with the company so I e-mailed him back to let him know what I had just found.

When I tested the water coming out of the softener after filling the tank it indicated somewhere between 7 and 15 grains per gallon.  When I tested the water coming out of the park supply faucet on our arrival I estimated the hardness at 11 gpg.  If that was accurate, the water had not changed, and today’s test was accurate, it meant our 8,000 to 10,000 grain water softener was exhausted in less than 5,000 grains by my calculations.  That did not seem reasonable to me so I plan to retest the water and the output of the softener, but today’s reading suggested that the water might be harder than I thought and that the softener was exhausted and needed to be recharged.

My main focus today, however, was laundry.  For Linda’s part she wanted to clean the inside of the coach, take care of something for our FMCA GLCC chapter, and then work on something for the bakery.  I decided to take my laptop computer to the laundry room and try to download Windows 10.  It’s a 3 GB download so there was no way we were going to do this using our Verizon data plan.  I did not know, however, if the resort Wi-Fi system would allow me to download that much data or have a fast enough data rate to complete the download in a reasonable amount of time.  What I discovered was that the public Wi-Fi only downloaded 2.65 MB in 45 minutes and ultimately disconnected me from the Internet.  I turned off the Wi-Fi radio in my computer and looked to see if there was some way to cancel the download.  Unfortunately I did not find one.  Not good.  Shame on you, Microsoft (once again).  Stuff like that is an advertisement for Linux.

Linda put the NFL AFC championship game on our living room TV and Ron, on our driver side, set up one on a table under his patio awning, so I got to listen to the game in surround sound.  Yippee.  I was going to take a nap (in the bedroom) but decided to stay up and continue working on today’s blog post, which was getting quite lengthy.

Around 4 PM we had sourdough pretzel nibblers and hummus for lunch.  It’s going to be another week before Gary can have Stacy proofread the three articles I have in the queue for Bus Conversion Magazine so I decided so spend the later part of the afternoon editing my blog posts for October 2015 and get them ready to upload.  I only got a few of them done and decided to take a nap after all.  I was not feeling well, which made it hard to concentrate and made this work an unpleasant chore rather than something I enjoyed doing.

I napped for a couple of hours, which I really needed, but I still did not feel right when I got up.  The late afternoon and early evening disappeared without accomplishing much of anything and we finally had granola for dinner around 8 PM.  We watched Downton Abbey from 9 to 10 PM on PBS and then watched the first of six episodes of The X-Files on FOX once the NFL NFC championship game ended and the talking heads ran out of things to say afterwards.  In truth, they ran out of things to say before they ever got started.

We were in bed with the lights out by 11:45 PM.  I set the heater pad on my side of the bed to 4 (out of 10) and was toasty warm in spite of the dropping temperature outside and inside the coach.  Juniper (our female cat) immediately climbed under the covers between us with her head between our pillows and settled in for the night.

2016/01/25 (M) TV Dilemma

The forecasted low temperature for last night was 37 degrees F.  The low temperature usually occurs just before sunrise; around 7 AM this time of year in Arcadia.  We woke up around then and checked the current weather on our phones which reported the temperature as 40 degrees F.  The temperature inside our coach was 56, three degrees colder than I have seen so far this winter, so I suspected the outside temperature dropped down into the upper 30s overnight.

I was feeling a little “off” last evening and did not sleep well last night, but not for lack of warmth.  I set the heater pad on my side of the bed to 4 (out of 10) and I was comfortable enough that way.  I had taken a nap during the afternoon, so I wasn’t really tired at midnight, but mostly I was unable to find a comfortable position.  Juniper (our female cat) got under the covers between our heads as soon as we went to bed, so that constrained somewhat my ability to change positions, which I did almost constantly; at least that was my perception.

We got up and put on our sweats, which is our standard routine for cold mornings unless we are leaving early to go somewhere.  I turned the Aqua-Hot on, turned on the three zone controllers, and set the thermostats to 70 degrees.  I then made our morning coffee and checked my e-mail while it was brewing.  The FMCA National Education Committee meeting that was tentatively set for today or next Monday (February 1st) was being rescheduled for February 8th or 15th.  That was fine with me; I have other things to work on right now and I am not looking forward to our committee’s discussion of meaningless survey data.  It’s not that I enjoy bring a nay-sayer, but there’s a science (and art) to doing surveys and as best I can tell the survey was not distributed in a way that allows us to treat the responses as representative of the larger population of FMCA members.

While we were enjoying our first cup-a-Joe a crow landed on the power pole just north of our rig (two sites away except that there is only one more site north of us).  Juniper spied it right away and began chattering the way she does when she sees birds and gets excited.  The crow eventually left and was replaced by our resident Pileated Woodpecker.  The woodpecker was clinging to the side of the pole, rather than sitting on the wires, where the pole has been pecked away and reduced in diameter for a length of some 10 inches (estimated) all the way around.  Pileated Woodpeckers are large, magnificent birds and are always a treat to see.  It eventually left and was replaced by a smaller woodpecker or Flicker but I was not able to see it well enough to be sure which one it was.

We like something hot and substantial on a cold morning, and oatmeal is our go to choice, so that was what Linda made for breakfast.  We did not have plans to travel today so we stayed in our sweats for most of the morning.  I finished my blog post for yesterday, started on this one, and then settled in at my computer to edit posts for October 2015.

I took a break and tested the water from the tap and softener.  Both readings were once again between 7 and 15 gpg so the hardness of the tap water had not changed since my original test and the softener was definitely depleted.  I checked to see if the clear filter housings I bought at the Arcadia rally would fit the pre-filter.  They did, so I cleaned them and substituted one for the opaque housing.  I configured the pre-filter housing with the flow constrictor tube, added 26 ounces of table salt, and started the water flow, allowing the discharge to drain on the ground.

After a couple of hours most of the salt was still in the bottom of the housing and I could see the top of the flow diverter tube so I knew there was a problem and had a good idea what it was.  The tube was not sealed at the top allowing water to enter the filter housing and go right back out without being forced down through the salt and into the slots at the bottom of the flow diverter tube.  I added an O-ring under the bottom of the tube and a rubber flat washer at the top.  I recovered the washer from one of the old filter elements.

I added another 26 ounces of table salt to the housing and reassembled it.  When I turned on the water pressure it pushed about half of the salt into the softener even with the outlet valve closed.  This was probably the first time since I made the diverter tube that my regeneration system actually worked as intended and, because of the clear housing, the first time I was able to visually observe it.  Because so much salt got pushed into the softener I ran just a little more water and then shut it off to let the brine develop and exchange ions with the resin.

For dinner Linda made a couscous dish with grape tomatoes and other yummy ingredients.  I was still not feeling 100% right but this dish was light enough and tasty enough to be appetizing.

We had a TV dilemma this evening; X-Files vs. Supergirl.  After many years absence FOX brought back a 6-episode season of The X-Files.  Episode 1 was Sunday evening after the NFL NFC Championship game but episode 2 was this evening at 8 PM, placing it opposite Supergirl on CBS.  Episodes 3 through 6 will also air on Mondays at 8 PM.  Buggers.  Our other Monday evening shows were all repeats but we watched them anyway.

The low temperature for overnight was forecast to be 50 degrees F with no storms.  That meant we could leave the windows open and the furnace/heaters off and get a good night’s sleep.

 

2015/10/17 (S) First Snow

Last night we removed the dining table from the back of my car and put it on the bed in the bus.  We then removed the two rear seats and put them in the garage.  We wanted the back of the Honda Element empty when we got up this morning as we do not usually have time to spare in the morning before driving to South Lyon for breakfast with the South Lyon Area Amateur Radio Club.

It’s always good to see our fellow hams and today was no exception.  We arrived just before 8 AM and stayed for over an hour.  We left around 9:15 and drove to Chuck’s shop in Novi to get the box with the two remaining lower windshields for our bus.  Chuck was already there and helped us load the box into the car.  The box was sized to hold five windshields but only had two in it so it was light enough for us to move by hand.  I knew it would fit in my car as we had measured it on a previous visit and I had checked the dimensions against the car.  We set one end on the tailgate, lifted the other end, and slid it in.  We chatted for a while, and looked at a project Chuck is working in for new front window shades, before heading home.

Phil was not at our house when we got home but he had obviously been there.  All of the concrete, and many of the rocks and boulders, were gone from the driveway extension area so I presumed he had loaded them in his truck and hauled them away.

The Converted Coach Owners (CCO) Halloween Rally was going on this weekend and today was the main day for activities.  We had intended/hoped to go to the rally but the progress on our bus remodeling has slowed over the last couple of weeks for various reasons, all legitimate, and it was not in a condition to travel or be used.  It’s not that things are not getting done; they are, just not as fast as we would like or need them to.  Among other things I have not yet secured the refrigerator and pantry.  We thought about driving over in the car but it was over two hours one way and we needed to spend what time we had available working on the bus and could not justify being gone.  Thanksgiving does not look/feel that far away anymore.  It also seemed ill-advised to be gone while Phil is here digging up the yard.

My main bus focus for today was completing the installation of the built-in sofa.  We had already set the plywood seat board on a blanket on the bus kitchen floor so I had access to the inside of the base/storage box.  I did not need Linda’s assistance for a while so she worked on her counted cross-stitch project.  Before starting on the sofa, however, I took care of a few other minor things.

First I replaced the alkaline batteries in the TempMinder thermometers with Lithium ones.  I then reset the minimum and maximum temperatures for the two remote sensors.  Sensor #1 monitors the freezer and sensor #2 monitors the fresh food compartment of the bus refrigerator.  The directions for the TempMinder suggest using Lithium batteries if the remote sensors will be in cold environments.

Next I got a piece of scrap SurePly underlayment to see how it would fit in the rabbited wood trim on the lower outside wall of the hallway.  I inserted it fully into a corner and marked the edges with a pencil.  It is approximately 3/16″ thick and fit nicely without being too tight.  With a layer of veneer it should be just right.  When I removed it the depth of the rabbits appeared to be 5/16″ to 3/8″.  I think the underlayment will make a nice base for hardwood veneer.  I will cut the panels 1/2″ wider (22-1/2″) and 1/2″ longer (28″) than the 22″ X 27-1/2″ dimensions of the framed opening and allow them to “float” just like a frame and panel door.

My last mini-task was locating the 1/4″ walnut veneered plywood we removed from the old refrigerator and measuring it to see if we had pieces big enough to panel the damaged area on the wall by the co-pilot seat.  I was pleased to find that the remaining pieces are large enough for this application.

By now it was 12:30 PM and my phone reminded me that we had an RVillage Ambassadors webinar/meeting at 1 PM.  Linda heated up some Amy’s Vegetable Bean Soup and made hot lentil loaf sandwiches with ketchup.  Yum.  We got our first snow flurries of the 2015-16 winter season during lunch and they continued off and on through the afternoon.  We moved to Michigan in May 1976.  It snowed on October 15th that year and we had snow on the ground every day until early April 1977.  While that has not held up over the years as a “typical” southeast Michigan winter it was very different from what we grew up with in Missouri and formed our first and most lasting impression of our adopted state.

I retrieved the link for the Go To Meeting from the RVillage website and put it in my web browser.  1 PM came and went with no meeting.  The meeting notice said “Saturday, October 17 at 10 AM PST” but they had clarified that was actually 10 AM PDT, which is 1 PM EDT.  We decided that perhaps they really meant PST, which would be 2 PM our time.  We tried again an hour later, but no meeting ever commenced.

When I finally got to work in the bus on the sofa I removed six screws, three each from two angle brackets, and pulled the entire base assembly out from the wall, giving me complete access to the HVAC duct and wiring chase.  Much of the final installation of the sofa involved this duct.

Powered and manual sheet metal nibblers with the opening Bruce just cut in the OTR HVAC duct and the piece of sheet metal that was removed.

Powered and manual sheet metal nibblers with the opening Bruce just cut in the OTR HVAC duct and the piece of sheet metal that was removed.

The ends of the plywood seat rest on two boxes with open ends that also serve as plenums for air from the OTR HVAC system ducts.  I needed to cut out rectangular openings in the vertical face of the duct to allow air into the back end of these boxes.  I used a 1/2″ drill to create starter holes at the corners of the openings and then used a manual sheet metal nibbler and a drill-powered reciprocating nibbler, both of which I borrowed from Chuck a few weeks ago, to cut out the sheet metal.  The two tools work differently but they both worked well and I was glad I had both of them for this task.  The powered nibbler created a lot of small metal debris so I vacuumed the whole work area very thoroughly when I was done nibbling.

The right (forward) end of the duct also had an extra hole in it where I did not need or want one.  I removed an old sheet metal patch plate and cut a new one to cover the area I needed to close off.  I ended up having to pre-drill holes as I spun the heads off two of my cheap sheet metal screws.  I had a heck of a time getting the shafts out, but I got it done.  This was just one more example of why seemingly simple projects always take longer than they should.

Phil returned while I was working on the sofa and continued trenching in the French drain.  I stopped to chat with him briefly and Linda came out to let me know she was headed to the grocery store.  I then got back to my own tasks and let Phil get back to his.

The left support/plenum box with the circular register hole cut in the face plate.

The left support/plenum box with the circular register hole cut in the face plate.

The open fronts of the two plenum boxes are attached to the inside of the vertical front support, which is 3/4″ walnut veneered plywood.  To get the air out of the boxes and into the coach my design called for brown plastic 4″ round louvered diffusers.  They are considered “four inch” because the two inch long cylindrical pipe on the back will just fit through a 4″ diameter circular hole.  (A 4″ flexible duct, like dryer duct, will also just fit over the pipe.)  The visible part of the diffuser is actually 5-1/2″ in diameter.

The inside width of the plenum boxes is 4-1/4″ by design.  I needed to center a 4″ hole within that space so I had to locate the center point for my 4″ hole saw very accurately side-to-side.  I also wanted the hole centered vertically.  Using my small square I marked the vertical midpoint on the edge of the front plywood at each end.  I then measured in 2-13/16″ from the midpoint mark and used my spring-loaded center punch to mark the center of the hole.   [The 2-13/16″ dimension came from half the inside width, or 2-1/8″, plus the thickness of the plywood used to make the plenums, or 11/16″.]

A close up view of the nylon mesh screen material used to cover the opening in the HVAC duct to keep critters that might get into the duct from getting into the support/plenum box.

A close up view of the nylon mesh screen material used to cover the opening in the HVAC duct to keep critters that might get into the duct from getting into the support/plenum box.

I stood the boxes on their back ends so the front board was horizontal.  I straddled the front board with my legs to hold it and drilled starter holes with a #6 countersink bit.  I then drilled the 4″ holes with a 4″ hole saw using my 1/2″ Craftsman corded drill, being careful to have the pilot bit in the starter holes and drill perpendicular to the face of the plywood.  I have had this drill for 37 years.  It is very powerful and has several ways it can be gripped quite securely.  It is large, heavy, and lacks the convenience of a cordless drill but when I need to use a bit with a 1/2″ shaft and/or need the torque, this is still the drill for the job.  The hole saw created some sawdust so I vacuumed the whole area thoroughly when I was done drilling.

I was just finishing this work when Linda got back from the grocery store.  She put the groceries away and came out to see if I needed any assistance.  I already had the roll of plastic screen in the bus and she got the Gorilla Tape from the garage.  I cut pieces of the screen large enough to cover the two rectangular openings in the HVAC duct and used lengths of Gorilla Tape to secure them.  We then slid the base/storage assembly back into position, pushed it tight to the HVAC duct, and reattached it to the wood wire chase on top of the duct.  The two support boxes and the return air box have foam weather stripping on the back edges to seal against the duct.

We picked the plywood seat up off of the kitchen floor and set it back in place but did not secure it.  We left it out several inches from its original position and got a seat and back cushion from the bedroom.  We experimented with different spacings and finally agreed that we need to have the seat out 4-3/4″ farther than originally designed.  The current hinge board is 11/16″ plywood, 2-3/4″ wide by just under 78″ long.  This board is screwed to the top of the wiring chase and to one side of the 72″ piano hinge.  I will replace it with a piece that is 7-1/2″ wide by the same length.  I will also have to provide some additional support for the seat side of the piano hinge as in the original design had both sides of the hinge resting on top of the wiring chase on top of the HVAC duct.

The Tulip Tree behind our house in its full fall glory.  This is the first photo to be posted in this blog taken with the new Sony a99v DSLT camera.

The Tulip Tree behind our house in its full fall glory. This is the first photo to be posted in this blog taken with the new Sony a99v DSLT camera.

That was the end of the interior bus work for today.  By the time we were done Phil had driven his front-loader onto his flat-bed trailer and secured it so it appeared he was wrapping up for the day.  I chatted with him about the project for 30 minutes before he left.  Earlier in the afternoon I had found my site plan drawings for the bus barn and agreed to stake out the driveway tomorrow so we could review it first thing Monday morning.

Linda had invited Meghan and Chris for brunch tomorrow but it was not a good weekend for them as the Michigan vs Michigan State football game was taking place in Ann Arbor.  Chris manages the Pizza House restaurant, and being away on football Saturday is not an option.  They will come next Sunday (31st) instead.

For dinner Linda made a nice salad of mixed greens with dried cranberries, sliced almonds, and diced onions dressed with raspberry vinaigrette.  The main course was pan-fried polenta with vegan puttanesca sauce.  It held its heat to the last bite and was very satisfying on a cold evening.  I opened a bottle of Cupcake Black Forest red wine.  We have had it before and, although drier than I prefer, it went well with the meal.

After dinner I got my flashlight and checked the bus for axle/hub seal leaks by looking under the bus from the opposite side to see the inside of the wheels.  I did not see anything to suggest a problem on any of the six positions and will text that information to Joe tomorrow for planning purposes as he would require a second day to work on the seals if that was needed.

We spent the last couple of hours of the day in the living room, with the fireplace turned on, reading, writing, and playing games while enjoying some red grapes for dessert.  Linda got a text from her sister-in-law, Mary, with a photo of her and Ron “standing on ‘the’ corner in Winslow, Arizona.”  Ron has been retired for many years but Mary only recently retired and they are on their first extended camping trip in their A-liner trailer and their first trip to the southwest U.S.

We went to bed around 10 PM.  Linda fell asleep quickly while I divided my attention between cooking shows on the Detroit PBS Create channel, a concert by Eric Clapton on PBS, and working on this post.

 

2015/06/20 (S) Cable Entry Box

We had not been to our local ham radio club breakfast the last two Saturdays because of the GLAMARAMA rally and a visit from Linda’s brother, Ron, and his wife, Mary.  The club was conducting VE testing today, rather than the usual 4th Saturday of the month, because the ARRL Field Day event is next weekend.  When we got to breakfast at 8 AM there were already a lot of people there and seven more came in after us.  We did not take a head count but it was somewhere between 25 and 30 people.  We also did not have our usual waitress but the substitute very efficiently got everyone’s order taken and delivered.

The 40 foot tower on the east end of the house with the old OTA TV antenna on top.

The 40 foot tower on the east end of the house with the old OTA TV antenna on top.

I checked with Mike (W8XH) and he is available to help us get the antennas mounted on the small tower on Monday or Wednesday, assuming I have the cable entry box (CEB) installed and all of the necessary coaxial cable on hand.  Getting the CEB mounted was my main goal for today, but not the first thing I had to do.  I called Chuck as we were leaving breakfast at 9:15 AM.  He was at home and suggested we stop by there and pick up a key to his shop.  He was working on landscaping when we arrived so we did not stay long and we were back home by 10 AM.  Linda finalized her shopping list and headed off to gather the things she needed to prepare tomorrow’s brunch.  I changed into my work clothes, gathered up the laundry, put a load in the washer, and got to work on the CEB.

The CEB is designed to mount on the outside of the house, allowing wiring to pass between the inside and outside of the house in a way that is weather tight and animal proof.  Coaxial RF cables and control lines enter through the bottom, connect to lightning arrestors in the CEB that provide a path to ground if/when needed, and then continue through the wall of the house and thence to various devices.  Those devices might include cellular phone signal boosters, Wi-Fi systems, TV sets, satellite receivers, personal weather stations, or amateur radio gear such as radios, remote antenna switches, and antenna rotators.

The general area on the east end of the house at the base of he 40' tower where the CEB will be mounted.

The general area on the east end of the house at the base of he 40′ tower where the CEB will be mounted.

Superficially the installation looked simple.  With the copper back plane removed there were four mounting holes, one near each corner, and two large holes in the back.  All we had to do was hold the box against the wall, mark the locations of the four mounting holes and the big cable entry holes, set the box aside, drill the holes, put the box back up and secure it.  Right.  Sort of, but not exactly.  Mounting the box took seven hours to complete.

The first step was to remove the copper back plane with the three lightning arrestors installed on it.  I took care of that yesterday.  The next issue was that the house has shiplap siding, i.e., the east wall where I needed to mount the CEB was not a flat surface.  I decided to use 1″ square aluminum tube, installed vertically along the back of the box at the outside edges, to span multiple siding boards, ensuring that the CEB would be plumb.  I also decided to leave the tube long enough to go all the way to the ground and use it to support some the weight, in effect creating legs for the CEB.  That was Linda’s idea.  She’s a smart girl and a licensed amateur radio operator.

The back of the CEB with one of the vertical mounting bars.

The back of the CEB with one of the vertical mounting bars.

We had some surplus pavers and garden blocks and I found one that was just wide enough to catch the bottom of the legs.  I also had some left over paver base material, which meant I did not need to make a trip to the store.  The paver base material was from a project long, long ago (in a place far, far away) and I used it to create a base for the foundation paver, which was approximately 18″ x 12″.  I leveled the base side-to-side and pitched it away from the house for drainage.

Yesterday I purchased a 3′ long aluminum tube at Lowe’s and a 4′ long tube at The Home Depot.  Three feet turned out to be a good length, so I cut a foot off of the 4′ tube.  Things then got trickier.  The positioning of the CEB was critical as the two large holes in the back were for adapters for 2″ plastic conduit.  I was going to have to cut 3″ diameter holes through the bond that would come out above the plate on top of the concrete block foundation.  In the chosen mounting location the bottom corner holes in the CEB would be below the siding.  The lower right leg would be at least an inch away from the concrete block foundation and the lower left hole would be in front of a basement window opening so neither of these were going to be screwed into anything.

The CEB in position on the east end of the house with the door open.  The copper backplane has been removed.

The CEB in position on the east end of the house with the door open. The copper backplane has been removed.

I wanted the CEB anchored at more than two points so I decided to drill two additional holes in the back, one on each side, approximately half way between the existing top and bottom holes.  I measured the spacing between the top and bottom holes as carefully as I could.  I measured down from the top end of each leg a distance for the top holes that was just sufficient to make sure the door of the CEB was below the 2″ iron gas pipe that runs horizontally along the outside of the house.  I measured down from there for the new middle hole and the bottom hole.  I then drilled the three holes through each leg by drilling opposing sides.  I had to use a powered hand drill for this work as my drill press was stored behind a large pile of RV furniture that we took out of the bus and was inaccessible.

I attached one of the legs to the back of the box using two short bolts through the top and bottom holes.  I then used the middle hole in the leg as a guide and drilled through the back of the CEB.  I repeated this procedure for the other leg.  I drilled the holes in the legs as accurately as I could but they did not quite line up so I had to enlarge them slightly by using the drill bit like a router bit.  Not ideal, to be sure, but aluminum is relatively soft and it worked.

The east end of the house with two 2" holes for the conduit.

The east end of the house with two 2″ holes for the conduit.

I attached each leg to the back of the CEB using 1.5″ 1/4-20 bolts through the bottom corner holes.  I snugged these up but left them loose enough that we could move the legs.  The top and middle holes were located in positions that would allow lag screws to be screwed into the siding and underlying plywood.  We had to tilt the legs to get them under the 2″ iron gas pipe and then straighten them and set them on the foundation paver.  We had to do this multiple times but it was easy once we figured out how to do it the first time.

With the CEB in position I marked the location of the holes for four 3″ 1/4-20 lag screws.  We removed the CEB so I could drill the holes for the lag screws and then put it back in position and screwed it to the wall.  I marked the locations of the two holes for the conduit as best I could and then unscrewed the box and removed it again.  I used our 1/2″ Craftsmen corded drill for the 3″ hole saw.  I bought this drill in 1978, along with a lot of other Craftsmen tools, when we moved into our house in Farmington Hills.  I still have almost all of those tools and they all still work.

The CEB in position with both pieces of conduit through the back.

The CEB in position with both pieces of conduit through the back.

With the conduit holes drilled I cut one of the 18″ lengths of conduit in half, inserted the pieces into the adapters, and placed them in the holes.  We then put the CEB into position, got the adapters through the holes in the back of the CED, and tried to line up the holes in the legs.  The conduit was being forced up as it went through the bond, especially the one on the left, and would not allow the holes in the CEB to line up with the holes in the legs.  We took the retaining rings off of the adapters and removed the CEB, again.

I shortened the conduit pieces to approximately 5″ and checked the fit in the holes.  We wrapped two bands of adhesive backed foam weather-stripping around each piece of conduit and placed them back in the holes.  I then applied a bead of adhesive caulk all the way around each adapter at the wall.  We put the CEB in position for the final time, got the conduit adapters through the holes, snugged up the retaining rings, and put the four lag screws in.  After tightening the four lag screws I tightened the two bolts in the lower corners.  I then tightened the adapter retain rings and put the open end caps on.  The conduit ended up getting pulled back out of the wall a bit so I used the thin end of a 10″‘wood shim to try and force the caulk back into the gap around the conduit adapter.  It did not go back in very well so I will have to figure out something else to seal around the conduit.

The CEB was finally installed and very solidly anchored.  I got the copper base plate and remounted it to the five studs (four corners and one center) using some antioxidant/anti-seize compound on the stud threads.  The last step (for today) was to install the snap in covers for the 16 cable entrance holes in the bottom of CEB.  I also ordered 16 grommets and will remove the caps and replace them with grommets as I install devices and run their cables and wires into the CEB.

The CEB with the copper backplane installed and the three Morgan lightning arrestors mounted (two lower left, one top center).

The CEB with the copper backplane installed and the three Morgan lightning arrestors mounted (two lower left, one top center).

The two pieces of conduit open into the sump pump room (large closet) in the northeast corner of the basement just above the wood plate that sits on top of the concrete block foundation.  I plan to install the SureCall Fusion5s 5-band cellular booster (amplifier) in this room to keep it close to the CEB and because there is AC power available there.  I bought an installation kit for the Fusion5s that includes a lightning arrestor which will get mounted in the CEB.  I also bought an amplifier for the OTA TV antenna that will mount on the tower a few feet below the antenna.  The amplifier will get its power through the coax from a power inserter that doubles as a lightning arrestor and will be installed in the CEB with the AC power supply (wall wart) in the sump pump room.

I did not get these two additional lightning arrestors installed today.  By the time we got the CEB installed we were tired.  The high temperature was OK (near 80?) but the relative humidity was very high.  I was also very sore the whole time, especially my left knee, undoubtedly the lingering after effect of using the power chisel earlier in the week to remove thinset and mastic from the floor of the bus.  Getting down and up at least 50 times during the afternoon did not improve matters, but we got it done.

Even though she was also tired, once we reached a point where I could finish up alone Linda got busy making several food items for tomorrow.  In the midst of all that she heated some Amy’s Lentil Soup and made grilled cheese sandwiches with Diaya cheese or dinner.  Diaya makes an excellent non-dairy cheese that works well cold or cooked into dishes.

After dinner I returned a call from Butch to find out more about their new property and buildings, and discuss bus and ham radio projects.  One of the things Linda made was an apple pie so we stayed up until it was cool enough to wrap up.  That turned out to be 10 PM, by which time we ready to turn in for the night.

 

2015/06/13 (S) On to Illinois

It has turned out to be a wet June so far and we had more heavy rain last night.  In spite of waking up during the night I was up at 7:30 AM and made coffee.  Everyone else got up as suited their level of rest and we sat around chatting for a while.  Ron put a load of laundry in the washing machine and then we sat down to a light breakfast.

Ron and Mary spent most of the rest of the morning repacking all of their stuff for the drive to northwest Illinois and their week-long bicycle ride.  FedEx Home Delivery delivered the Cyclo 5-Pro Mark II Dual Head Orbital Polisher I ordered along with all of the foam pads and detailing chemicals.

Ron retrieved their laundry from the dryer and after they finished packing we had a light lunch.  By 1 PM they were ready to load up the car so we helped get their bags out.  After a brief “farewell and safe travels” they were on their way.  They had a five hour drive but would gain an hour as they entered the Central Time Zone so they would be at their motel by 5 PM local time with plenty of daylight and time to eat dinner.

Linda took a short nap and then went for a walk.  I read through the manual for our SureCall Fusion5s cell phone booster and was part way through the manual for the Cyclo 5 when I decided to take a nap.  Linda returned from her walk and a little while later a USPS mail carrier delivered the OTA TV antenna I ordered from Antennas Direct.  All I am waiting for now is the cable entrance box I ordered from KF7P Metalwerks.

Once the cable entrance box arrives I will have a bit of a project.  First I will need to drill two 2″ holes through the east wall of the house and into the sump pump closet in the northeast corner of the basement, mount the box to the wall, and ground it to the outside ground rod by the tower.  I may also need to install additional ground rods.  I will then need to climb the tower by the house and do the following:

  1. take down the old OTA TV antenna and rotator;
  2. mount the new OTA TV antenna and aim it;
  3. mount the amplifier for the OTA TV antenna;
  4. attach a short piece of 75 Ohm co-ax from the antenna output to the amplifier input and weatherproof the connections;
  5. attach a longer piece of 75 Ohm co-ax to the output of the amplifier and weatherproof the connection;
  6. mount the outside antenna for the cell phone booster system;
  7. attach one end of a 50′ piece of LMR-400 or RG-213 co-ax to the cell phone antenna and weatherproof it;
  8. unmount our Diamond SG7900 2m/70cm ham radio base station antenna and remount it at the top of the tower;
  9. attach a 50-to-60 foot length of LMR-400 or RG-213 co-ax to the ham radio antenna;
  10. dress and secure all of the coaxial cables with plastic cable ties (zip ties).

Once I am done with tower work I will need to do the following to complete the installation:

  1. install the lightning arrestors in the cable entrance box for the cell phone booster and OTA TV (?) co-ax cables;
  2. route each of the co-ax cables into the bottom of the cable entrance box and attach them to appropriate lighting arrestors;
  3. attach additional co-ax cables to the lightning arrestors and feed them through the 2″ holes into the basement;
  4. mount the Surecall Fusion5s in the sump pump room and connect the co-ax for the outside antenna and the power supply;
  5. run a 50′ length of LMR-400 from the sump pump room across the basement ceiling and up through an old vertical furnace exhaust chase to the attic;
  6. drill a hole in the ceiling of the main floor hallway near the chase;
  7. mount the inside done antenna for the cell phone booster system to the ceiling with the co-ax dongle in the attic;
  8. connect the antenna dongle to the co-ax coming up from the basement;
  9. run additional co-ax from the sump pump room to the ham shack;
  10. run additional co-ax from the sump pump room to the video distribution point in the laundry room (or directly to the locations of the two TV sets);
  11. turn on the Fusion5s booster (transceiver), adjust the gain (if needed) and test it with our phones and Mi-Fi;
  12. test the TV sets (and hopefully not have to go back up the tower to reposition the antenna);
  13. connect our Icom IC-7000 amateur radio and test the antenna connection.

As I wrote out this list it occurred to me that I need to make a list of all of the co-ax types/lengths/connectors I need and that, at a minimum, I probably need to order a length of LMR-400 orRG-213 co-ax cable and the proper N-connectors to complete the ham radio antenna connections.  It also occurred to me that I might be able to do some of the inside wiring while I am waiting for the cable entrance box to arrive.  Also, once the TVs are connected Linda can scan for channels and communicate with me with our HT ham radios if I need to change the aim of the antennas on the tower.

All of this reminded me that I need to follow-up with a Bratcher Electric on running a new 100 Amp main feed from the transfer switch to the panel in the furnace room in the garage.  I also need to order some new split foam fillers from Critter-Guard and new electrical hardware for connecting the bus to the toad from EZ-Connector in California.

I must have been sleeping lightly and dreamed all of these details because I got up from my nap around 5:30 PM, finished reading the manual for the Cyclo 5, and then took a shower and got dressed for dinner.  Barb Spera had called Linda yesterday to see if we were available for dinner this evening.  They had really enjoyed our meal at La Marsa in Brighton a couple of weeks ago and wanted to go again so we agreed to meet them there at 7 PM.  We did not have to wait for a table and our waiter, Najheem (Naa-gheem), was delightful.  Barbara had the Koshary again, and Chuck had the Chicken Shwarma with tabbouleh salad, while we split an order of spicy vegetarian ghallabah with rice and a salad.  I had a mango smoothie and we all enjoyed the swarm pocket bread and garlic spread.

It was after 9 PM when we got home and we headed off to bed at 10.  We knew Ron and Mary had arrived at their destination because Ron played a Scrabble word.  Linda had also checked that our daughter and son-in-law were on their way back from Las Vegas.

 

2015/06/12 (F) Forms and Family

I was awake at 6 AM but not fully rested so I stayed in bed.  I got up at 7:30 AM, fed the cats, cleaned their litter tray, and then settled in at my desk to continue editing blog posts.  I had edited four more posts by 9 AM when I heard footsteps and running water, signaling that people were up and about.  I wrapped up my work and went upstairs to make coffee.

We sat around drinking coffee and tea and visiting.  Both cats have gotten more comfortable with Ron and Mary being here, but especially Juniper, who is seeking their attention and sleeping on the living room sofas while we sit and talk.

Ron and Mary were expecting a package today but found out late yesterday that it had not been sent.  As a result they needed to have documents e-mailed to us so they could deal with them and return them before they leave tomorrow for a week-long bicycle ride in northwest Illinois.  The e-mails came through and all of the documents were PDFs so they were easy to save and print.  I restarted my old Dell Precision Workstation in Windows 2000 Pro mode as that is where the scanner is installed and we would need it later to scan the signature pages, save them as PDFs and e-mail them back to the sender.  (I normally use this computer to run Linux.)

I left at noon for a 12:15 PM appointment at the Honda dealer to have the oil changed in my Element.  My car has just under 99,000 miles and really needed its 100,000 mile service, but I did not have time for that today so I had them change the oil and scheduled a return visit for Wednesday June 24 at 10 AM.  It has a torn driveshaft boot on the driver side front and the mechanic thinks the drive shaft should be replaced as water and dirt have certainly gotten in there and there is probably rust.  Ron tended to concur with that opinion.

Linda gave me a short grocery list before I left and I went to the Brighton Meijer’s after my car appointment.  By the time I got back Ron and Mary had finished reviewing documents.  I was going to scan the signature pages but it turned out that one of the signatures had to be notarized and the documents had to be faxed back in their entirety.  Linda researched places to get all of that done and they were headed out to take care of that as I returned home.  While I was out UPS dropped off a package from Prevost Parts with the window panel seal I ordered earlier in the week.  That’s two UPS deliveries to this week so my confidence is restored.

While Ron and Mary were out Linda made potato salad and I worked in my office.  I restarted my Dell Workstation in Linux mode (Ubuntu 14 point something) and installed about 45 updates.  While that was happening I edited a few more blog posts and got caught up.  Now all I have to do is post them.

Brendan, Shawna, and Madeline drove up after Madeline got up from her afternoon nap.  They arrived around 4 PM.  I quit working at my desk just before that and came upstairs.  Madeline is always excited to visit Grandma Linda and Grandpa Bruce but having Ron and Mary here was a bonus for everyone.

For dinner Linda served the potato salad, baked beans, and vegan cheese burgers with all the fixin’s.  We had a break in the rain and she cooked the burgers outside on the grill.  We had fresh strawberries and non-dairy “ice cream” for dessert.  Ron and Mary picked up an apple pie from the Grand Traverse Pie Company store in Brighton so everyone else tried some of that as well.  Conversation was about family, work, and travel.

By 7 PM Madeline was showing signs of being tired so Brendan and Shawna gathered up their things and headed back to Ann Arbor.  We stayed up until 10 PM talking, but did not play Mexican Train, and then turned in for the night.

 

2015/06/11 (R) Absent 34

Ron and Mary had a long drive yesterday, and an exhausting 10 days prior to that, so they went to bed tired.  Consequently they did not get up early and I did not make coffee right away.  I was up at 7:30 AM and went to my office instead.  Chris at KF7P Metalwerks accepted my change to the cable entrance box late last night and sent me a PayPal invoice.  I paid that this morning and e-mailed him back to clarify and confirm a couple points about the box.  Once everyone was up we had coffee (us) and tea (them) on the back deck and enjoyed a beautiful early summer morning.  We eventually went back inside and had the granola for breakfast that Linda made yesterday.  So good.

After breakfast we gave them a tour of our partially disassembled motorcoach and explained what we are trying to do.  I mentioned that the motorized windshield roller shades were not winding up straight and that the driver side was binding part way up.  One of the MCD vendors at the rally last week told me to put a piece of tape on one end (lengthwise) to force the shade to not run (in that direction).  Ron, who is a retired mechanical engineer, suggested that I create a tapered roller by putting tape around the roller tube at 5 to 7 places.  The tape cannot go all the way around the roller tube because of the shade but it can go most of the way around.  Ron’s suggestion was one layer towards the outside, two layers next, then three layers and finally four layers in the center.  These tapered rollers are commonly used in industry to keep conveyor belts centered.

We had just exited the bus when a minivan that I did not recognize pulled in our driveway.  It was the electric power company meter reader.  We chatted briefly, and she was very nice but was obviously on a tight schedule.

Ron and Mary needed a duffle bag and some batteries so we drove to the Dick’s sporting goods store at US-23 and Lee Road.  They found a nice duffle bag but not the batteries so we stopped at Meijer’s on the way back to the house and they found what the needed there.  We also picked up a card for our daughter, Meghan, whose 34th birthday was today.

Back at the house we called Meghan and wished her a happy birthday via voice message.  We got a text message later saying thank you.  We also had a voice message on our home phone from Pat Davidson at Apex Roofing indicating that the shingles for our new roof would be delivered on Monday.  For lunch we had pretzels and pita chips with hummus and some grapes.  I slipped off into the small bedroom and opened the box from Cellular Solutions to make sure everything was there.  It was.

Although Ron and Mary slept well last night they were still tired and decided to take naps.  That left Linda free to go for a walk and me to work in my office.  I transferred rough drafts of blog posts from my e-mail to MS Word and then started editing them but did not have time to upload them to WordPress before we had to leave to go to dinner.

We left around 5:15 PM for La Marsa.  They were in the second of two days of their 4th year celebration for the Brighton location and everything was 34% off.  They were backed up 90 minutes for carry out orders but we got a table after only a short wait.  We had Koshary and they had kabobs.  After dinner we went for a walk around the Brighton Mill Pond where we saw two gigantic snapping turtles in the pond.  One of them almost caught a muskrat and they eventually bumped into one another and seemed to be fighting.  It was quite the show.  Snapping turtles are nothing to mess around with and the shells on these two were about 2 feet long, front to back.  Gigantic.

When we got back to the house we played 13 rounds of Mexican Train.  By the time we finished it was midnight and we all got to bed around 12:15 AM.

 

2015/06/10 (W) Ron and Mary

Same routine as yesterday; up at 7 AM, open up the house, feed the cats, clean the litter tray, start a load of laundry, make the coffee, and drink the coffee while using our iPads.

Our daughter’s 34th birthday is tomorrow but she is flying to Las Vegas today to meet up with her husband who is there on a company outing.  We will celebrate her birthday when they get back, perhaps in conjunction with Father’s Day and Linda’s birthday, which is at the end of the month.

Linda left at 9 AM for Brighton Honda to have the 12 V battery in her car checked.  The battery light came on the other day so we thought it might need to be replaced.  Around 9:20 AM I heard thunder and a short time later we had a brief, heavy downpour.  Linda called at the same time and said the battery tested OK.  The problem could be the alternator, of course, but presumably the dealer service people know that and checked for that.  If not, we will likely be back there sooner rather than later.

Linda headed on to Meijer’s to do the grocery shopping.  Today was trash pickup day so I took the trash can to the street.  After meeting with Brad from Chuck It Junk Removal the other day we decided we would rent their trailer for 5 days.  For the same price as having them physically handle 1/3 of a truck of junk (5 cu. yd.) we can get rid of a full truck of junk (15 cu. yd.) by loading it ourselves.  Deal.

I got a call from Phil Jarrell regarding my request for pricing to dig a foundation hole for a ham radio tower foundation.  It was a useful conversation in that I had not previously realized that I will need a concrete contractor in addition to the concrete supplier.  The only thing the concrete supplier will do is show up with a cement mixer truck and dump the concrete where they are instructed to.  The concrete contractor will actually place rebar, build forms, provide carts or a pumper, and get the concrete from the truck to the hole.  Phil recommended Mike Fearer of Bid-Rite Concrete as a good guy who would work with me to get this done.

I talked with Chuck about getting a key to his shop so we could have the new refrigerator delivered there and have the old one picked up without having to trouble him to be there.  He agreed and suggested that we contact the guy down the street about removing the old windshield and installing the new one as part of the refrigerator swap.

Rather than dig into our bus interior remodeling project I have used the last couple of days to finalize decisions about various products and order them.  One of the things I have wanted/needed for a while is a cable entrance box that will allow me to route transmission lines and control cables into the basement from outside.  I talked to Chris Perri, KF7P, at the Dayton Hamvention last month and decided that I liked his custom fabricated cable entry boxes.  I got his business card at the Hamvention and exchanged a couple of e-mails with him this week.  I decided this morning how I want the box initially configured and e-mailed my specs to Chris.  I would like to run the cabling for the cell phone booster through this box so I needed to get it on order.  Speaking of which, the cell phone booster system arrived today via UPS so I am feeling more comfortable that all of the stuff I am ordering will actually get delivered to our house.

Wednesday’s and Fridays are when Recycle Livingston is open and the Wednesday hours are 11 AM to 5:30 PM.  We had my car loaded up with recyclables and Linda drove over after lunch to drop them off.  When she got back she made a batch of her yummy granola and I got a couple more loads of laundry done while continuing to work at my computer.

After doing my alternate tile layout for the bus floor yesterday I decided that I liked the way it looked better than the original ad that it would not involve any more cutting than the row/column layout.  I also felt confident that I had an accurate enough tile count to go ahead and order the tiles.  I drove to the Shell station to fill my tank and then drove to Lynch Carpet in Howell.  I ordered 12 boxes of the 16″ x 16″ Armstrong Alterna Luxury Vinyl Tile in the La Plata Creme Fresh pattern, and a gallon each of the vinyl adhesive and Glacier vinyl grout.  There are 14 tiles per box (24.89 sq. ft.) for a total of 168 tiles (just under 300 sq. ft.).  The inside floor area of the bus is around 300 sq. ft. before subtracting out walls and cabinets but we will be using some of the tiles on vertical surfaces in the entry stairwell and cockpit and around the box that supports the bed platform.  My estimate is that I will have 10 extra tiles.  The guy at Lynch Carpet suggested that I use a scrap piece of tile as a spacer when installing the tiles but I may use the little plastic “X” pieces designed for this purpose.

From Lynch Carpet I drove to Lowe’s in Howell to see if they had a different portable air compressor that might be more appropriate than the 6 gallon Porter Cable we just bought.  The Porter-Cable air compressor has a maximum regulated pressure of 150 PSI but that is also the maximum tank pressure.  I will have to test it on one of the front bus tires to determine if it will get the job done and if not I will return it.

The guy at Lynch Carpet also suggested that I rent a handheld grinder from Abe’s or A-1 Rental, both in Howell.  Abe’s did not have any grinders of any kind and A-1 was closed on Wednesdays.  The gal at Abe’s suggested the tool rental service at the Howell Home Depot, so I stopped there.  They also did not have a handheld grinder but they did have a floor model concrete grinder.  It was so heavy that I doubt if we could have gotten it into the bus and it was too big to maneuver in the tight spaces where I need to work.  They did have a lighter/smaller floor stripper and I may give that a try before I resort to grinding off the thinset with an angle grinder and diamond impregnated wheel and/or a belt sander with a very aggressive belt.

Pat Davidson called from Apex Roofing while I was out so I called him back.  They will be able to start on our roof next week Monday or Tuesday and will deliver the shingles on Friday this week.  I confirmed that we wanted two of the 14″ light tunnels for the living room.  I also indicated that I had scrapped the idea of building a dormer or installing a roof hatch as I simply did not get this taken care of in time.

Linda had closed up the house and turned on the air-conditioning while I was out.  It was pulling moisture out of the air but would not bring the air temperature lower than 78 degrees.  Not good.  This will be our third summer in this house and we have not used the air-conditioning very much.  The first summer we were gone for most of June, all of July, and a few days in August.  We had the unit serviced last year and thought it was working OK but perhaps did not really use it after that.  We did install filters in the return air grills so perhaps they are restricting the airflow too much.  It is also possible that it needs refrigerant.  I will have to check our records from last year and then call TOMTEK to arrange to have it serviced again.

Linda’s brother, Ron, and his wife, Mary, arrived early this evening.  They are on their way to northwest Illinois for a week-long organized bicycle ride.  They have to be there on Saturday and will be spending the next three nights at our house.  Visits from them are usually not more than once a year but we really enjoy their company when they are here.

For dinner Linda made a nice green salad and then made whole wheat angel hair pasta with onions, garlic, and mushrooms lightly sautéed in olive oil.  Ron does not imbibe but Linda, Mary, and I had a glass (or two) of Moscato.  We moved to the deck after dinner and had fresh strawberries for dessert.  It cooled off as darkness set in and we eventually moved back inside.  The other three were in the kitchen and I was sitting on the sofa when Juniper suddenly caught a mouse in the middle of the living room, or at least that is where I noticed that she had it.  She took it downstairs and I got her to drop it in the bathroom sink but I was unable to get it into a container to take it outside and it escaped into my office.  I closed the doors but I have no doubt it can go wherever it wants in the house from there.  When I returned upstairs we chatted until 11 PM and then all turned in for the evening.

 

2014/12/21-25 (N-R) The Holidays Arrive

2014/12/21 (N) Winter Solstice

Linda was reading an interesting tidbit online this morning about the winter solstice, which occurs today in the northern hemisphere.  It usually occurs on the 21st, like today, but occasionally slips into the 22nd.  While it is the day of the year with the least hours of sunlight (between sun up to sun down) it is not the day with the latest sunrise (which occurred a couple of weeks ago) or the earliest sunset (which does not occur for a couple of more weeks).  Why is that?  Axial tilt, elliptical orbits, and a “day” that is not exactly 24 hours.  Science is fun.

Today was a stay-at-home / stay-in-town day for us.  Linda vacuumed the coach and mopped the floor tiles.  She says she likes to do this once a week to keep the cat hair under control.  By “likes” I think she means “needs.”  She also decided to do the laundry.  When we are at our house the laundry is usually my chore but for some reason, to which I am not privy, she takes over this chore when we are living in the RV, at least initially.  The same thing happened last year at Williston Crossings RV Resort, although we eventually both did laundry until I was able to win back my rightful chore.  So far again this year it has been her self-selected task here at Quartzsite and I have not gone out of my way to reclaim my rightful place as master of the laundry.

What I did instead of laundry was spend the morning finishing our 2014 Year-in-Review holiday letter.  Linda proof read it and then I converted it to PDF and did a final check of the layout to make sure the text and photos had not shifted or been clipped.  I copied it to a flash drive so we can take it someplace in Blythe tomorrow and have it printed.

The other day I noticed that the manifold pressure sensor (turbo boost) on Butch and Fonda’s 6v92 was mounted vertically on the front passenger side of the ECM.  I could not see exactly how it was mounted, however, so today I finally looked it up in the DD 92 Series manual.  I did not attempt to reattach our sensor module today but I was curious to see what would be involved.  I also continued to interact with other Prevost owners on the Prevost Community forum regarding the turbo boost issues and the dashboard gauge, which does not have the correct scale for our engine.  That thread has led to a dialogue about the SilverLeaf systems, including the VMSpc that we have, and an alternative system from RV Tech Tools that uses an iPad app named “RV Dash” and a wireless (WiFi) interface named “CANpod” from Cubix Labs.

With our various chores done we had a light lunch of chickpea salad on a bed of mixed greens and then went for a long walk.  The walk took us down Washington Ave. and then over to Kitsap Ave. to see a gorgeous Adobe house that Linda had discovered on a previous walk.  That led us to the backside of the west-central “vendor” (flea market) area on the north side of Main St.  We are not collectors, and we are not into antiques, guns, rocks, jewelry, or junk, so we saw very little that interested us.  We did see a few pieces of Pyrex, which our daughter and son-in-law were collecting at one time, and I am always on the lookout for a good deal on a tool I can’t live without, but mostly we saw endless quantities of stuff that we could not fathom anyone buying.

We crossed Main Street and visited the Tyson’s Well Stagecoach Stop Museum.  The grounds and building were open, admission was free, and it was unattended.  There were items for sale and if we had wanted something we would have put the money in the collection box.  That’s small town.

We headed east on Main Street and crossed back to the north side using the crosswalk at AZ-95 (Central Ave.).  We then continued east and stopped at the Road Runner Market.  We were pleased to find that they had a small but good selection of fresh produce.  On our way out the door the florist gave Linda a red and white carnation.  We will definitely be doing some of our local grocery shopping there.  We knew there was a restaurant/bakery on the far east end of Main Street so we kept on walking.  Sweet Darlene’s looked like a nice local place for a home-cooked style meal, but did not have anything on the menu we could eat.  The bakery turned out to be a small display case with pies and sweet rolls, but they did not make their own bread, so we won’t have any reason to come back.

By this time it was getting to be late afternoon, the cloud layer had thickened, and it was getting a bit chilly so we headed back towards Central Avenue.  We counted laundromats along the way, and passed at least four before getting back to our coach.  Not that we need a laundromat—we have a laundry where we are staying—but with all of the boondockers in and around Q it is a matter of some curiosity to us how/where they take care of things like this.  By the time we got back to our coach we had walked just over five miles.

Sunset over the Dome Rock Mountains due west of our encampment.

Sunset over the Dome Rock Mountains due west of our encampment.

By 5:15 PM the sun had slipped just below the mountains to our southwest and the sky started to glow pink for 360 degrees around us.  The sunset went on for over 30 minutes, the pinks deepening to reds.  And then, just like that, the color was gone and darkness enveloped the valley.

For dinner Linda made a simple green salad with raisins and peanuts.  She then heated up some vegan re-fried beans, pan-grilled a package of fajita vegetables she got from Connie before they left, and then heated two tortillas.  We each made a tasty roll up, adding some salsa and vegan sour cream.  She washed some black seedless grapes and set them out for desert.  They were very refreshing after the somewhat heavier and spicy main course.

2024/12/22 (M) Compressed

We had planned on driving to Blythe, California today but those plans changed fairly early in the morning.  Butch got an update that his air-compressor was on a UPS truck in Blythe and scheduled for delivery today.  I had promised to help him with the installation and provide a few tools he did not have with him so we decided to stick around camp.  We were also waiting for Connie’s realtor, Carolyn, to come by and pick up two yellow Post Office slips.

Linda took her morning walk after breakfast while I downloaded the October and November issues of Bus Conversion Magazine in both standard- and high-definition.  I was really glad to finally see these issues.  The October issue included my article on our T. F. Hudgins Spinner II Centrifugal By-pass Oil Cleaner project.  That was my one remaining article waiting to be published.  I have at least a half dozen in process, at least that many more for which I have taken photos (and written blog posts), and a very long list of future projects, so it’s time to get the next batch of articles ready to submit.

When Linda got back I drove to the print/copy/fax/pack/ship/etc. store on east Main Street to see if they could print our holiday letter.  They had plain 8.5×14 white paper, and the photos looked OK, but it was going to cost $4 per letter ($2/side) so I paid for the one copy and left.  They suggested that I try Weeks Printing in Blythe (20 miles west) or Staples in Lake Havasu City (70+ miles north).  Since we will likely head to Blythe tomorrow we will check out Weeks first.

As long as I was out I stopped at Barry’s Breads and bought a couple of fresh “rolls” which were really small loaves of bread.  Barry runs a little seasonal bakery out of a temporary vendor stand on the northeast corner of Central Avenue (US-95) and Kuehn Street.  Most of his products have butter or cream cheese as ingredients—his Danish pastries are as big around as a dinner plate—but he does make just plain bread and everything is made fresh daily.  Back in camp Linda called Weeks Printing and they quoted $1.25 for each 2-sided letter.  Much better.  We will check them out when we make it to Blythe; probably tomorrow.

For lunch Linda made a batch of her scrumptious chickpea salad/spread and served it on one of the rolls I bought at Barry’s.  After a week of cloudy skies, cool temperatures, and a little rain we finally had a day with clear, sunny skies and the high temperature up into the 70s.  Butch decided to remove his defective air-compressor and there wasn’t anything we could do to help (or stop him) so we decided to clean some more of our coach exterior.  I wanted to work from the top down, which meant starting with the roof.  That, in turn, meant getting out the Little Giant convertible extension/step ladder and setting it up as a 14 foot extension ladder.  In this configuration it extends beyond the top edge of the roof at the front, making it safer for me to get up on the lower roof area from the driver’s side.

Rinsing down the roof of the coach (photo by Linda).

Rinsing down the roof of the coach (photo by Linda).

The roof was very dirty and it appeared that we might have more than just embedded dirt to deal with.  The roof has a sprayed-on ceramic-infused white coating with a surface akin to medium grit sandpaper.  It reflects sunlight and provides a nice nap for walking on, but also traps dirt.  The last time the roof was cleaned was in early April, just before we left Williston Crossings RV Resort.  I had been on the roof subsequent to that, in our pull-through driveway at home, using it as a platform for trimming tree limbs.  I do not recall it being unusually dirty at that time, but I was focused on other things.  If it had been, I probably would have washed it, but maybe not; I was focused on other things.

I used a little bit of Dawn dish soap in several gallons of water and our soft, long handle, brush to try and scrub it clean and then rinsed it with softened water.  It was better by the time I was done but far from 100% clean.  I also scrubbed all of the metal awning covers and then hosed them off and rinsed the awning fabric.  When I was done on the roof I sprayed off all four sides of the bus, but even with the softened water it left spots and streaks.  Another unfortunate side effect of this work is that it frightened our male cat, Jasper, who ended up hiding behind the steering column in an attempt to escape the sights and sounds of a ‘monster’ on the roof.

We would like to get the body clean but there’s no point doing anything until I get the roof finished (Linda does not climb ladders and she does not get on the roof of the bus.)  At a minimum I am going to have to use a stiff scrub brush and a stronger solution of Dawn dish soap, or perhaps a commercial cleaner that can treat mold/mildew along with just plain dirt.  We will then have to do the vertical surfaces in small sections, scrubbing, rinsing, and drying as we go.  We have a sprayer for our hose that has a small bottle for additives and one of the reasons I bought it was to try using a dishwasher rinse aid, like Jet Dry, to see if it would eliminate spotting.  To-date, however, I have not tried that.

The old Bendix Tu-Flo 700 air-compressor out of Butch & Fonda's MC-9.

The old Bendix Tu-Flo 700 air-compressor out of Butch & Fonda’s MC-9.  The governor is the silver thing on the left.  The open port on top is the air discharge where the unloader valves are located.

Once Butch had the old air-compressor out of their bus he turned the input shaft and noted that the pistons were not pumping air.  This confirmed that something had failed internally and ordering a replacement was the right thing to do.  There wasn’t much else to do so we all sat around in the warm sun and waited for the UPS truck to show up, which it finally did around 3:45 PM.  We (me, Linda, and Fonda) suggested that Butch wait until tomorrow to start installing it, but we knew that was not going to happen.  The compressor was a significant road failure that had bugged him since it happened and he was anxious to get it fixed.

 

The new (re-built) Bendix Tu-Flo 700 air-compressor with the old spline and new port plugs.

The new (re-built) Bendix Tu-Flo 700 air-compressor with the old spline and new port plugs.

The Bendix Tu-Flo 700 he received is designed specifically for mounting on Detroit Diesel 92 series 2-stroke engines but has more ports on it than are typically used in this application.  Making sure to match the configuration of the old compressor, Butch installed new plugs in the unneeded ports.  He then removed the fittings from the old unit one at a time and installed them in the new one, being careful to line them up exactly the same way.  I helped by holding the compressor on a work table while Butch tightened the pipe threads.  This was the easy part of the project as we were standing at a tall bench with plenty of room to work and good light.

 

The new air-compressor with fittings.  Note the alignment marks for orienting the fittings correctly.

The new air-compressor with fittings. Note the alignment marks for orienting the fittings correctly.  The spline is in the upper left of the photo.

The hard part was getting the air-compressor re-installed.  Butch eventually got it onto two of the four mounting studs, which then took the weight.  We discovered a clearance issue with one of the port plugs and he had to pull the compressor back out.  He removed a plug from the old compressor, which did not stick out as far, and reused it in the new compressor.  With the compressor back on the studs it now lined up better but the spline would not engage the drive gear on the end of the engine camshaft.  He put a wrench on the crankshaft pulley nut and turned the engine slightly by standing on the end of it while I jiggled the air-compressor.

The "governor" mounted on the new compressor.

The “governor” mounted on the new compressor.

The spline eventually engaged the engine gear and the air-compressor gear enough that Butch was able to fully seat the flange and insert/tighten the four mounting studs, lock washers, and nuts.  Per the instructions, he reconnected all of the lines except for the air discharge and called it a night.  The coolant goes back in tomorrow and Butch will then start the main engine to make sure the compressor works, check for leaks, and let any contaminants get blown out the discharge fitting.  If everything looks good he will attach the discharge line, which connects the outlet port of the air-compressor to the coach air system, and air up the bus.

The new air-compressor (blue) mounted on the rear of the engine block (towards the front of the bus).

The new air-compressor (blue) mounted on the rear of the DD6V92TA engine block (towards the front of the bus) in Butch and Fonda’s MCI MC-9B NJT.

At least we were successful in convincing Butch to wait until tomorrow to put the coolant back in the engine.  By the time we finished working, put our tools away, and got cleaned up it was 7:30 PM and had been dark for two hours.  Linda reheated the leftover fajita fixings and we had open-faced tortillas with Fritos corn chips, salsa, black grapes, and Sangria.  We were both tired so we relaxed for a while after dinner and then went to bed.

2024/12/23 (T) Blythe, CA

We got a call from Connie right after breakfast letting us know that the two packages Carolyn picked up yesterday were for us and Butch.  We needed to pick them up before 11AM as Carolyn had an appointment at that time.  Linda was headed out for her morning walk anyway so she walked to Rock Reality, near the post office and uptown drugs, to get the packages from Carolyn.  (Carolyn is Joe and Connie’s realtor.)  She dropped off the two P. O. Box – Mail Pickup Notice cards at the post office while she was there.

Our package was from Madeline (Brendan and Shawna), to be opened on Christmas Day.  Butch’s package was the unloader valve kits for our Bendix Tu-Flo 700 air-compressors.  He ordered them while we were in Forest City, Arkansas for delivery to Amarillo, Texas but they did not arrive in time so his friend forwarded them to our Quartzsite location.

Butch and Fonda used most of the morning to put the coolant back into the engine.  Our buses, which still have their over-the-road heating systems, hold a lot of coolant.  Ours requires 34 gallons.  The buses are not identical, but I suspect theirs requires at least 30 gallons.  And it is very important that the cooling system is filled to capacity and has had all of the air purged out of it.  It’s a big, messy job.

They got as much in as they could by standing on a ladder and pouring it through a funnel into the filler tube for the surge tank.  The radiators on the MCI MC-9 are located above the engine, one on each side wall at the rear of the bus, and the surge tank is located above them, so the filler tube is approximately 9 feet from the ground.  Butch started the engine to warm it up enough for the thermostat to open and to circulate the coolant and opened a couple of bleeder valves to let air out.  He also checked the outlet fitting on the new air-compressor to verify that it was pumping air.  It was (hurray!), so he shut the engine off, attached the air line to the outlet fitting, and started it back up.  The chassis air system (suspension and brakes) came up to pressure and the air-dryer “sneezed” (momentarily opened its purge valve) so the system was fully operational.

We planned to go to Blythe, California today and Butch and Fonda wanted to go too, so he shut off the engine and they cleaned up their campsite.  We were sitting in our coach when the winds came up rather strong.  Linda checked the weather and the winds were out of the north at 20 MPH and forecast at 22-25 MPH until 6 PM.  That was strong enough for us to retract our awnings, close our roof vents, collapse our folding chairs, and stow our patio mat.  Butch and Fonda also retracted their patio awning and stored all of their outdoor equipment and furniture.  We had the old patio awning on our Itasca Sunrise torn off by strong (thunderstorm) winds while we were away from the motorhome and have been extra careful about awnings and wind ever since.

With all of that done we headed to Blythe in their Chevy Suburban.  From 879 feet ASL in Q we climbed to about 1200 feet ASL over the low mountain range that separates the two valleys, and then descended to 240 feet ASL as we crossed the Colorado River and entered California.  A few miles later we took the 7th Street exit and we were there.  The 20 mile drive was only five more miles than the trip we made from Williston Crossings RV Resort to the Publix grocery store (at the southwest corner of Gainesville, Florida) last winter, so it did not feel like a long way to go for groceries.  At home we have supermarkets about five miles away in three different directions.  Butch and Fonda typically drive into Logansport for their groceries, a distance of 12 miles, so we are all used to traveling some distance to purchase our food.

The Smart & Final Extra and the Albertson’s were on the NW and SE corners of 7th and Hobsonway, just north of I-10, making them especially convenient for us, so this is where we will likely shop every other week or so.  But our first destination was a few blocks farther west on S. Main St. where we found Weeks Printing.  They were eventually able to access our flash drive and open the PDF of our holiday letter.  They had a high quality paper in 8.5”x14” size, and were able to print our letter 2-sided on a good quality color laser printer for a very reasonable price of $1.25 per letter ($0.625 per side).  They did not take credit cards so we paid cash, but it saved us a 73 mile trip (one way) to Staples in Lake Havasu City.

Self-portrait of the blogger.  I am merely a reflection of my former self.

Self-portrait of the blogger. I am merely a reflection of my former self.

At the Smart & Final Extra we bought fresh produce, soy milk, and some bulk, canned, and packaged items.  They did not carry the Silk brand soy coffee creamer that I like, and there were a few items Butch and Fonda needed that the store did not have, so we drove across the street to Albertson’s and got those items.  I stayed in the car with the groceries, but I already knew that the Albertson’s would be a nice store based on our experience with the chain in Sheridan, Wyoming during summer 2013.  With our shopping done we returned to Quartzsite.

I carried the groceries from the car to the bus and Linda stored them, discovering that she had an empty tub available in the cabinet above the refrigerator.  By the time she was done it was approaching 4 PM so she prepared chickpea salad sandwiches as a quick, light lunch and then announced that we should go for a walk before it got dark.  She let me chose the route so we crossed Central Avenue (AZ-95) and walked to the city park, which has a very nice baseball field with lights and the only grass we have seen in Quartzsite.  There was also a skateboard facility, a football field, and two F4 Phantom jets (minus the engines and other equipment).  The Quartzsite Metal Detecting Club (QMDC) has a practice field adjacent to the park.  The park is located near the following municipal facilities:  Community Center and Library, County Court, Police Station, and Post Office Annex (where most of the P. O. Boxes are located).  The Fire Department is a little farther north on Tyson Wells Street just east of Central Avenue.

The sun was getting near the tops of the mountains to our southwest so we headed pack to our coach and settled in for the evening.  For dinner Linda made a barley risotto with garlic, shallots, mushrooms, sun-dried tomatoes, vegetable both, and seasonings.  While she was cooking I got a call from my dad and got him caught up on our whereabouts and activities.  The risotto was excellent and we each enjoyed a glass of sangria with our meal.

I don’t know if we are just relaxed, or really tired after a hard summer and fall, but we have both been going to bed earlier and waking up later than usual.  Or perhaps it is just the effect of fresh air and sunshine.  Whatever the reason, it’s nice to be able to just sleep when that is what we feel like doing and get up when we are read.

We have an excellent Verizon signal here in Q.  Linda often likes to pace up and down Lollipop Lane while talking on the phone.  If you lived on Lollipop Lane you would too.

We have an excellent Verizon signal here in Q. Linda often likes to pace up and down Lollipop Lane while talking on the phone. If you lived on Lollipop Lane you would too.

2014/12/24 (W) Christmas Eve

It’s Christmas Eve and we woke to a temperature of 37 degrees, clear skies, light winds, and no snow.  The forecast high for today was 66, with no snow.  Do I miss snow at the holidays?  Not really.  At one time (high school) I considered myself something of a “romantic” in the sense that I liked the classical music of the romantic era, but I am not particularly nostalgia.  If I was, we would own a restored 1957 Chevy; red, of course.  No, we had snow at home before we left and as a harbinger of things to come we took it as a sign that our departure was overdue.  Christmas in the desert will be a new experience for us, but so far it looks very agreeable.  We will miss being with family, of course, but we are not alone here and technology keeps all of us much more connected than it once did.

Having been to Blythe yesterday we did not have any last minute shopping to do today.  The desert was there yesterday and will be there tomorrow (I presume) so we did not have to see it today.  With the holidays upon us I did not feel like working on bus projects.  Linda started addressing the envelopes for our Year-In-Review Holiday Letter and then worked on food preparations for tomorrow’s dinner with Butch and Fonda.  It seemed like a good day for me to finally start catching up on some things that I have not had time for in a while.  For instance, I need to work on articles for Bus Conversions Magazine, update our bus project list/status, update our website, upload some blog posts (OK, a LOT of blog posts), and catch up on the blogs I follow using the Feedly app on my iPad.  I am way behind on all of these tasks and starting to feel some pressure about it, albeit self-imposed.  I do not have to do any of these things if I don’t want to, of course, but they are activities that I enjoy and want to do.  Still, being way behind takes some of the fun out of it and makes it a bit more like work.  I won’t get caught up in one day or one week or even one month; it will take many weeks of persistent effort.

After checking e-mail, I settled in to work on my article about the exterior renovation of our motorcoach.  Michele Henry of Phoenix Paint helped me finish the article in early October but I still needed to select and caption all of the photos.  While I worked on that Linda walked to the Road Runner Market and managed to snag the last 3-pack of yeast.  When she got back she made her orange cranberry relish for tomorrow’s dinner.

We took a break for lunch and then Linda headed out for her daily power walk.  When she got back she continued addressing envelopes for our holiday letter.  Just as I was feeling like I needed a break, Butch knocked on the door to let me know he was working on a small project that might interest me.  He had already burped the coolant lines that supply heat to the living area of their bus when driving and gotten the last of the coolant into the system.  His new project was getting an alternator driven tachometer connected and calibrated.

It turned out that he needed positive DC power to the tachometer in addition to the ground and RPM signal.  He was able to temporarily pick up 24VDC from the positive terminal of the starter, found a convenient ground point, and picked up the rotational speed from the stator terminal on the back of the alternator.  With the engine running at low idle he measured the RPM of the main crankshaft pulley using an optical sensor instrument.  It was just over 600 RPMs so he adjusted the tach via a set screw on the rear to match the reading.  He kicked it into high idle and measured the rotational speed as 950 RPM.  That is what the tach displayed within the precision of the markings.  He already has a signal wire run from the engine compartment to the cockpit but needs to mount the tachometer in a separate bullet housing, connect the wire on both ends, and provide positive and negative (ground) DC to the instrument.  He decided not to take on that project today.

(Note:  RPM is universally understood to be an abbreviation for “Revolutions Per Minute” but that is not necessarily correct.  An object such as the pulley on the end of an engine crankshaft rotates about its own axis, just as the earth does, and has angular velocity which is properly measured in rotations per some unit of time or angular displacement per some unit of time.  The abbreviation is, of course, still RPM.  In the case of the pulley, however, Butch put a small piece of white tape on the face of the pulley at the outside edge to act as a target for his optical sensor.  If we consider the piece of tape as a separate object then it does, indeed, revolve around the center axis of the pulley, just as the earth revolves around the sun.  Viewed thus way, revolutions per minute is technically correct.  As with many things in physics, it depends on your frame of reference.  So much for today’s physics lesson.)

This building houses (L-2-R) the laundry room, the apartment, and a small workshop.

This building houses (L-2-R) the laundry room, the apartment, and a small workshop at our compound.

As long as I was outside I borrowed Butch’s metal detector and went in search of a couple of tie downs that Joe told us were buried somewhere near the outer edge of our patio awning.  I knew they were lined up with a reference mark on one of the concrete patio slabs and it did not take long to locate and uncover them.  We put a couple of medium-sized rocks on top of them so we could relocate them easily.

We got several multimedia messages from our son today with pictures of our grand-daughter at our daughter’s house helping make cookies.  Brendan, Shawna, and Madeline are spending the night and Katie is joining them tomorrow.  Butch and Fonda will spend most of the day at the local church Fonda selected, including a carry-in (pot luck) luncheon, but will have dinner with us around 6:30 PM.

I finally returned to our coach and worked on my article about the Zena power generating system I installed to charge our house batteries while driving.  Again, the article was mostly finished a long time ago, but I could not submit it until I completed the installation, got the system operational, and took a few more photos.  All of that happened in October and November but I was too busy with other projects and preparations to pull it all together at that time.  I had a couple of e-mails today from Gary, the publisher of Bus Conversion Magazine, indicating that the December 2014 issue might not be out until early January 2015, and wondering if I might have a finished article they could use.

For dinner Linda made a salad of dark mixed greens with raisins, nuts, and pear slices drizzled with raspberry walnut vinaigrette dressing followed by pan-seared tofu slices with caramelized onions and bar-b-que sauce served open-faced on hamburger buns.  We split a Sam Adams Pumpkin Spice Ale.  I am not a big fan of ales or pumpkin but beer seemed like the right beverage for this dish.  It was OK, but I would have enjoyed a Yingling or Shiner Bock more.

I made good progress on both articles today.  I got an e-mail from Mike, the editor of BCM, wondering if I had a finished article.  The ZENA article was close enough that I decided to finish it and upload it to our Dropbox before going to bed.  I e-mailed Mike back to let him known it was there and offered to finish the other one by the end of the weekend.

Earlier in the day I updated our personal WordPress site to the just released version 4.1 and updated several plug-ins and themes.  My last task before turning in for the night was to replicate the update process on the other three sites I manage.  By the time I got to bed it was Christmas Day.

2014/12/25 (R) Christmas in Q

The wind came up strongly overnight and we were awakened by the rattling of the vent fan domes.  From our north facing bedroom window we could see flags and the tops of trees blowing briskly in the wind.  We could also hear and see the awnings on the south/passenger side of the coach flapping.  Linda checked the weather channel app on her iPad and it reported winds at 20 MPH.  We were not expecting winds that strong until the daytime and they were strong enough for us to be concerned about our awnings.  By that point we were wide awake so we put on our sweatpants and shirts, slipped on some shoes, found a set of keys, got the step-stool out of the front bay and the awning rod out of the folding chair bay, retracted the two awnings, returned the rod and step-stool to their respective storage compartments, and finally went back to bed.

Linda got up at 6:30 AM in order to start making cinnamon rolls from scratch.  I usually get up first and make a pot of coffee but I was up past midnight working, so I slept in for another hour.  The yeast she bought yesterday wasn’t cooperating so we turned on one of the Broan ceramic cube heaters to try and create a warmer and more consistent environment to get the dough to rise.

We borrowed Butch and Fonda’s Verizon MiFi (unlimited data plan) so we could Facetime with our children and their families, who were gathered at our daughter and son-in-law’s house.  We got to watch all of them open the presents we left for them when we were there on Thanksgiving and they got to watch us open the gifts they sent with us or shipped to us here in Quartzsite.

Brendan, Shawna, and Madeline (son, daughter-in-law, and grand-daughter) sent a 2015 Shutterfly Calendar with photographs of all the different family members placed on the dates for birthdays, anniversaries, and such.  We do not need much at this point in our lives, but a collection of photographs that also reminds us of the people and dates that are most important to us is something we appreciate and treasure.  Meghan and Chris (daughter and son-in-law) bought us each a genuine Tilley hat.  I have known about these hats for a while but never bought one.  Given our outdoor oriented RV lifestyle, these were excellent gifts.

After we were done with our Facetime session Linda took the cinnamon rolls over to the apartment to bake since it has a range with an oven.  She will finish cooking dinner there later and the four of us will eat there this evening as it has a table that will seat four people.

The apartment bedroom.

The apartment bedroom.

In spite of early indications to the contrary the cinnamon rolls rose and baked just fine. The dough used flour, salt, vegan butter, yeast, and flax meal with water (egg substitute) and a little sugar.  The filling was made with brown sugar, vegan butter, cinnamon, and maple syrup.  The topping was a glaze of sugar, water, and vanilla with raisins and chopped walnuts.  Linda took two of them over to Butch and Fonda and we had some for breakfast still warm from the oven.  It’s a good thing that these are as much work to make as they are or I might want them for breakfast every day.   🙂

Linda had a call and TXT message from her sister (Marilyn) and sent a reply.  She was on her way to her housemate’s family gathering and they agreed they would talk later today.  She also sent merry Christmas TXT messages to her sister-in-law, Mary, and good friend, Diane.  At noon our time (1 PM CST, UTC-6) I called my sister to wish her a happy holiday.  Her daughter, grand-daughter, and future son-in-law had already been there in the morning as Ryan had to work that afternoon.

I made a second pot of coffee, which is unusual for us, but we planned to spend the day lounging around the coach cooking (Linda) and working on the computer (me).  Linda cleaned up the breakfast cookware, poured another cup of coffee, and started working on the chocolate cake for tonight’s dessert.  With the cake prepared and in the apartment oven she turned her attention to making the candied yams.  Once those were done the only thing left to do was bake the Tofurkey, roast the asparagus, and heat the gravy.  It was a lot work for her but it was spread out over two days and she enjoyed, and did it, willingly.  We could have gone out for dinner if she wanted, even though we would not have found much we could eat, but I am glad she preferred to cook.

Once I wrapped up the conversation with my sister I got back to work on the Outside Makeover (Exterior Renovation) article.  Although I thought I was done writing I made a few more edits and selected additional photos.  By 5 PM I had 74 photos selected and placed in sequence to match the flow of the article.  I had also done as much of that work as I cared to for the day.

We were down to 1/4 tank of fresh water so I decided to refill it.  About that same time Linda decided it was chilly enough in the apartment that she wanted the propane space heater turned on so I shut off the water and took care of that.  The heater had a hose that went through the wall at floor level to the outside with a regulator and POL fitting on the end of it.  I found a couple of 20 lb. propane tanks in the workshop and connected one of them to the regulator.  It took a while but I eventually got the pilot flame to light and then got the heater to ignite.  I then went back and finished filling our water tank.

The little apartment is very cute with three rooms: a bathroom on the east end, a bedroom on the west end, and a kitchen/dining/living room in the middle.  It has a shower, a 4-burner electric range with an oven, a refrigerator/freezer, a small microwave oven, the aforementioned space heater, a small window air-conditioner, a small TV/monitor with a satellite receiver, two easy chairs, a small dining table with four chairs, and a queen sized bed.  Marilyn is seriously considering coming for a visit the last week of January and if she does she will stay in the apartment and get to experience Quartzsite.

Linda starting to set the table in the apartment for Christmas dinner.  No pictures of Butch & Fonda (they are camera shy).

Linda starting to set the table in the apartment for Christmas dinner. No pictures of Butch & Fonda (they are camera shy).

We bought a bottle of Sternthaler Nurnberger Christkindles Gluhwein spiced red holiday wine at Central Market in Fort Worth, Texas to serve with our Christmas dinner.  It is a mulled wine that is supposed to be gently heated before serving, but we found it quite agreeable straight from the refrigerator.  About 20 minutes before dinner time we set it out on the counter to warm up slightly, the space heater doing a very effective job heating the small apartment even on its lowest setting.

Linda and Fonda both contributed dishes to the meal and Fonda made a couple of things that we could eat.  They brought chicken and traditional mashed potatoes for themselves but also tried some of the Tofurkey roast.  Linda made a vegan chocolate cake for dessert and whipped refrigerated coconut milk solids to use as a whipped cream substitute.  Our daughter did this for the Thanksgiving meal and we really liked it.

We sat in the apartment for a long time after dinner and just talked until we were all tired.  Linda and Fonda had already cleaned the dishes so we turned off the propane space heater and carried all of our stuff back to our coaches.  Linda put the leftovers away while I did a final check of my e-mail for the night.  I then shut my computer off and we headed to bed.  Like so many things in our retirement RV lifestyle, this Christmas holiday was a new and good experience.

 

2014/09/25 (R) Two M’s

Linda made zucchini bread and muffins a week or so ago.  We ate all of the muffins within a couple of days but she froze some of the bread.  She took the bread out of the freezer last night to let it thaw so we could have it for breakfast this morning.  She warmed it up and made a fruit salad to go with it, along with our usual fruit juice and coffee.  Marilyn took advantage of her visitor status and slept in so we had breakfast without her and she ate when she finally got up.

Madeline in her sofa-bed with her Winnie-the-Poor sleep sack.

Madeline in her sofa-bed with her Winnie-the-Poor sleep sack.

I was working on the electrical outlets in the garage when Brendan arrived at 9:45 AM with Madeline in tow.  Meghan arrived around 10 AM, so Madeline had all the “buddies” here to admire her.  I finished my electrical work, touched up some drywall compound, and then got cleaned up.  I was once again the designated reader and got to read three books to Madeline.  She had lunch at noon and her dad got her down for a nap around 12:30 PM.  Meghan is still experimenting with foods, so she left to do her grocery shopping on the way home.

The "buddies" (L-2-R): Brendan, Marilyn, Meghan, and Linda.  (Not shown: Bruce, taking the photo.)

The “buddies” (L-2-R): Brendan, Marilyn, Meghan, and Linda. (Not shown: Bruce, taking the photo.)

Brendan stayed for lunch and a long chat.  He was thinking about leaving when he decided to check out my old Toyo view camera.  He figured the students in his history of photography class at the University of Michigan had probably never seen one and wanted to take it in for them to see.  He also wanted to have it at his house to play with.  We found it and checked that all the parts were there and he loaded it into his car along with the tripod and dolly (studio roller base).  Madeline started to wake up so he made his exit.  She doesn’t seem the least bit concerned if he’s not here when she wakes up, but is momentarily distressed if she sees him leave.

Flowers along the Mill Pond boardwalk (Brighton, MI).

Flowers along the Mill Pond boardwalk (Brighton, MI).

Madeline is spending the night tonight so we will two M’s here the rest of the day and tomorrow morning.  Linda and Marilyn will take Madeline back to Ann Arbor tomorrow in time for lunch and her 1 PM nap.  Madeline has swimming on Fridays at 4 PM so Linda and Marilyn will leave before that and stop at Whole Foods Market before taking Marilyn to Detroit Metropolitan Airport for her evening flight back to St. Louis.

I took a few minutes to check e-mail while Madeline was napping.  This morning I had tightened up the Wordfence parameters on the FMCA-GLCC site and switched the caching from the faster Falcon Engine to the Basic setting in order to fully activate country blocking.  I only had a few failed login attempt e-mails so I think it made a difference, but only time will tell.  I also white listed our own IP address to make sure we did not get locked out if we mis-typed our login credentials.

Madeline with Grandma Linda on the Brighton Mill Pond boardwalk.

Madeline with Grandma Linda on the Brighton Mill Pond boardwalk.

I had an e-mail from my niece, Amanda, with a couple of pictures of her daughter, Lilly, a very pretty and sweet-tempered child about six weeks younger than Madeline.  We saw them in late June and will like try to visit again en route to the southwest this winter, weather permitting.  If not, we will certainly try to stop in the area on the way back in the spring.

When Madeline awoke from her nap we let he play long enough to fully wake up and then we all went to downtown Brighton.  We walked the boardwalk along the east edge of the Mill Pond and saw a Painted Turtle, an egret, some fish, and lots of ducks and geese.  We then took the pedestrian bridge to the west side of the pond where the playscape is located.  The playscape is a wonderful place with structures built to suggest animals and Madeline explored it thoroughly with Grandma Linda’s help while I took pictures.  It also has an area with chalk boards and a mailbox full of sidewalk chalk that the kids can use to draw.  Madeline spent quite a while trying all the different colors.

Madeline with Grandma Linda at the playscape by the Brighton Mill Pond.

Madeline with Grandma Linda at the playscape by the Brighton Mill Pond.

We stopped by Lowe’s on the way home to return the spark plug I bought last night and get the correct one.  By the time we got back to the house Madeline was hungry so Linda got her dinner ready right away.  For our meal Linda prepared a green salad with sunflower seeds and dried cranberries topped with Ken’s Sweet Vidalia Onion dressing (one of our favorites) and a one pot meal of quinoa with black beans, corn, and onions.  Linda and I finished the Red Guitar Sangria with dinner (Marilyn does not drink alcoholic beverages).

Madline working with chalk at the Brighton Mill Pond playscape.

Madline working with chalk at the Brighton Mill Pond playscape.

Madeline played quietly with Linda for a while as I chatted with Marilyn. Before we knew it, it was time for Madeline to go to bed.  The time between dinner and bed always seem short compared to other intervals during the day.  She is always very good about bedtime and went without a fuss.  Linda spent about 30 minutes getting something ready to e-mail to the bakery software vendor while Marilyn played Words With Friends and I researched where we could buy more Red Guitar Sangria.  It is available at the Meijer’s stores in our area and is very reasonably priced so we will probably get some more.  We had apple crisp for dessert after which Linda and Marilyn played three-way online Scrabble with each other and their brother Ron in Pennsylvania.

 

 

"I think this color goes right here."

“I think this color goes right here.”

Madeline is a very good-natured and relatively calm child but when she is awake she is full engaged with the world around her.  We were all tired after a long but very satisfying day of visiting and turned in without watching any TV.