Tag Archives: roasted red pepper hummus

2015/12/28 (M) On to Arcadia

Leave a reply

Even though we were pulling out this morning we did not set an alarm to get up at some particular time.  We were up by 7:30 AM anyway. I did not make coffee or have breakfast and started preparing for departure.  We packed up our computers and put them on the bed, put away remote controls, and turned off the laser printer and NAS.  While Linda cleared off counters and secured drawers I took care of some outside things.

I pulled the tow bar parts bags out, set them aside, got out the tow bar adapters for the car, and inserted them.  I folded up the two bag chairs and put them in the car and folded up the plastic table and stowed it in the front bay.  I checked the pressure in the two front/steer tires on the bus and they were fine so I did not have to get the air compressor and hose out.  I put up all of the awnings and opened the air valve for the engine accessories and toad braking system.

When everything else was ready Linda pulled the car out while I turned on the bus chassis batteries and started the bus engine.  I let the chassis air up, pulled up the tag axle, pulled out of our site, and then backed up until I was parallel with, and close to, the edge of the road on the passenger side and not blocking anyone’s driveway.  Linda pulled the car up behind the bus and we connected it for towing.  The breakaway cable finally broke so I got the spare cable out of the glove box but I could not get the key out of the disconnect.  Rather than risk breaking it and thereby disabling the car, we decided to travel without it.

We had a final, quick chat with our neighbor’s, Danny and Dorothy, and with Ken on the other side, and pulled away around 9:10 AM.  We were out of the resort and headed southeast on US-27 at 9:26.  At Ocala we headed south on I-75 as far as exit 301 (Cortez Blvd) at Brooksville, and headed east on FL-700 as far as US-98 and headed south.  Most of this segment was also co-terminus with US-35.  The drive was mostly rural and very pretty.  It was warm outside but patchy clouds kept the temperature inside the coach from getting too warm, at least for a while.  Eventually I turned on the OTR HVAC system and it worked well.

We passed through several smaller towns but eventually got to Lakeland which was much larger, with lots of stop lights and traffic, so it took longer to get through.  Still, it was an attractive community and something to see besides an Interstate highway.  The Detroit Tigers spring training camp is in Lakeland and we will likely drive up for some games while we are in this part of Florida.

US-17 joined up with US-98 as we were leaving Lakeland.  Somewhere south of Lakeland (Fort Meade?) US-98 turned east towards Sebring and we continued south on US-17 to Arcadia.  A few miles before reaching US-70 west of Arcadia we turned onto NE Turner Road which ran due south towards the Turner Agri-Civic Center and bypassed downtown Arcadia.  We pulled into the Civic Center, which was the rally venue, at 1:15 PM.

Linda checked in with rally organizers/hosts Bill and Brenda Phelan.  Linda stayed with the coach while Bill drove me over to check out sites.  I selected site #9 which would have us facing west with our passenger side facing north.  Although this orientation put the afternoon sun on our windshields, it also provided shade in conjunction with the patio awning.  Dan (?) led us over to the site and then left us to unhook the car and back the bus in.  We leveled the coach (we thought) and I shut it down and went through our arrival preparations.

The inside of the coach was cool from the OTR HVAC and I wanted to keep it that way, so we left the windows and roof vents closed and put the insulated foil panels in the three large skylights.  We also found the snap covers for the side windows next to the driver seat and installed those.  We were able to position the coach which generous space to our passenger side and far enough back that the 25 foot shorepower cord just reached the outlet box.  After plugging in we turned on all three of the residential air-conditioners.  We deployed all of the awnings, including the patio awning, to shade the windows and provide a shady place to sit outdoors.  We also have a fresh water and sewer connection but may not use them while we are here.  We are only here until Friday or Saturday and came in with a mostly full fresh water tank and mostly empty waste tanks.

Although it was very warm (86 degrees F) and humid the clouds had thickened and filled in during the second half of our drive and there was a good, steady breeze.  The bus ran well today including the OTR HVAC.  The low pressure light only came on briefly one time while I was idling at a stop light.  Apparently it works a lot better when it is relatively warm outside.

Once we were set up we had a light lunch of roasted red pepper hummus and sourdough pretzel nibblers with fresh apple slices and orange segments.  We then drove to Walmart to pick up some anti-itch cream and bought a few grocery items while we were there.  We checked out the filling station on the property and decided it was not a good choice for our bus.  We also found the entrance to Big Tree RV Resort which was, literally, across the street from the Walmart.  We drove back towards downtown and stopped at the Winn-Dixie to see if they had a better selection of boxed wines than the Walmart.  They did, and we bought a Franzia Crisp White.  We drove the rest of the way into downtown in search of a filling station with diesel fuel, and access for large vehicles, before returning to the rally site.

Linda wanted to go for a walk so we strolled past the buses and other RVs that were already here.  We ran into Scott Crosby working on Dan’s windshield.  We met Dan, Kathy, and their son James at the FMCA GLCC Surplus and Salvage Rally back in September.  Apparently the windshield on their GM PD4106 started coming out of its gasket along the top and caving into the cockpit on their trip to Arcadia.  Scott was up on a ladder getting the gasket reseated around the frame and glass.

We continued our walk and discovered that Paul and Claudine Elbisser, also from our FMCA GLCC chapter, were here.  We visited with them for quite a while before finishing our stroll around the rally and returning to our rig for dinner.  Linda microwaved a sweet potato and served the last of the Gardein stuffed mock turkey roll and broccoli that we had for dinner on Christmas day.

After dinner I tried tuning in OTA TV stations, orienting the antenna both WNW towards Tampa St. Petersburg, and due south towards Port Charlotte, Punta Gorda, and Ft. Meyers.  When I scanned for stations I found about 60 in each direction although many of them were the same stations.  So much for digital TV signals bring highly directional.  We watched reruns of our Monday evening TV shows on CBS.  We also turned on the Verizon Mi-Fi so we could get online long enough to check TV tower locations and network affiliations, check our e-mail, and change our location in RVillage.

I got an e-mail from Gary at BCM with the draft of the February 2016 issue and a request that I proofread Part 1 of my 2-part article on our Habitat For Humanity RV Care-A-Vanner build in July 2013.  I was a little tired from our day’s activities and was not in the humor to review articles, edit old blog posts, or write new ones so I just watched TV and fiddled with the thermostats and fan speeds on our air-conditioners.  I was puzzled by the fact that it felt humid in the rig in spite of the air-conditioners having been on all day.  The front and rear ones seem to be cooling better than the middle one, but the front one was the only one that we seaw water dripping from the drain line outside the bus.  I admit to having some level of concern about where the condensed water from the evaporators is going, assuming they are condensing any moisture.

The overnight low was forecast to be about 70 with morning fog, i.e., 100% relative humidity so in spite of the fan noise we left the bus closed up and the A-Cs running.  I adjusted the thermostats down to make sure the condensers would run, and lowered the fan speed in the bedroom to reduce the noise level.  I plugged the power in for the rear OTA TV antenna, but it was not functioning correctly and was clearly not going to fix itself.  It needs to be replaced but I am reluctant to buy another one of the same model as the failure rate so far has been 50%.  Linda read, and I played a few games, on our iPads and then went to sleep.

 

2015/10/08 (R) A Mighty Hose

Leave a reply

Linda was up before 6 AM to drive to the bakery ahead of the worst of the morning rush hour traffic.  I was aware of her getting up but fell back asleep.  She is very quiet as she goes about her preparations on such mornings, which I appreciate.

I got up around 8AM, fed the cats, and cleaned their litter tray.  I made half as much coffee as usual and measured out a bowl of granola, probably a little more than usual.  I took my coffee to the living room and turned on the fireplace, expecting to settle in with my cats and work on my iPad, but the iOS 9.0.2 update was available so I started the installation and read the last few pages of Number Theory and Its History by Oystein Ore.  I read from screens more than from paper these days, but I still like to curl up with a printed book.

Jasper used to sit next to me on the sofa in the morning but seems to prefer sleeping on top of one of the back cushions these days.  Juniper, who never used to pay much attention to me, has taken his place.  She has always sought out warm places to curl up but has always preferred Linda’s lap to mine.

My bus project for today was reassembling the plumbing to the two fan-coil heat exchangers that go in the bases under the two desk pedestals.  Yesterday I cut new holes for the supply and return hoses.  My first task was to remove the hoses from the bleeder valves and install barbed plastic plugs in the ends to prevent coolant from coming out.  I then pulled the hoses back and out through the new openings.

The area behind the desk where the heater hoses emerge from the passenger side OTR HVAC duct.

The area behind the desk where the heater hoses emerge from the passenger side OTR HVAC duct.

I worked on the hose for the right hand (rear most) heat exchanger first.  I positioned the base, routed the hose to the lower fitting, and marked where to cut it.  I put a plastic paint tray liner under the hose before I cut it but more coolant came out than I expected.  I got as much of it in the liner as I could and grabbed a bunch of paper shop towels.  I got the liner outside without spilling any antifreeze and poured the used antifreeze in a one gallon jug that I keep for just this purpose.  I used a funnel that is also reserved for use with antifreeze.

I took the cut off piece of heater hose outside, plugged end down, and set the open end in the tray liner.  We already had a bucket of soapy water in the bus as we had planned on hanging wallpaper yesterday.  I wrung out the sponge and then squeezed some of the soapy water on the floor and cleaned it up with paper shop towels.

The left and right desk bases and center cover/spacer set in place. The heater hoses are not yet connected.

The left and right desk bases and center cover/spacer set in place. The heater hoses are not yet connected.

With the mess cleaned up I slipped two hose clamps over the end of the hose and worked it onto the lower fitting on the heat exchanger.  If only it had been as easy to do as that description!  The 3/4″ i.d. rubber heater hose did not just “slip” over the 3/4″ o.d. copper pipe even with some residual antifreeze lubricating the inside of the hose and the outside of the pipe.  Indeed, it took considerable and simultaneous pushing and twisting to get the hose on.  It was also a lot harder than I expected to work with the heat exchangers installed in the bases, even without the desk pedestals in place.

I was interrupting my work as needed to take photographs and as I finished up the first hose the camera refused to trigger the shutter.  The LCD screen indicated that the compact flash memory card was full so I went to my office to offload the images from the last few days.  My other CF card was empty so I put that in the camera and set it aside.  I had not backed up my photos to the Network Attached Storage units in quite a while so I decided to take the time to do that.  While I was at it I backed up my blog posts from December of 2014 through July of this year along with several issues of The Gypsy Journal.

As long as I was at my computer I checked my e-mail accounts, logged into RVillage, and logged into my account at B&H Photo.  My new Sony alpha 99 and accessories were on their way from New York and due to be delivered by the end of the day tomorrow.  I am excited to finally be getting a new digital camera with a full frame (35mm) sensor that will work correctly with all of my old Minolta A-mount lenses.

By this point it was lunchtime so I cleaned up (antifreeze is definitely NOT good eats) and scrounged around the kitchen for something tasty but easy to fix.  My “go to” meal is usually roasted red pepper hummus and sourdough pretzel nibblers.  We had a little hummus left, which I finished, but I was still hungry so I made a bowl of popcorn.  I would probably not make a good bachelor.

I went back to the coach and contemplated attaching the other hose to the left heat exchanger.  While I was thinking about it Linda called to let me know she was on her way home.  It was 1 PM so I decided to wait for her to get home to help me install the second hose.  I had some phone calls to make and used the time for that.

I called Karen at Bratcher Electric to schedule the upgrading of our 60 Amp sub-panel in the garage to a 100 Amp main panel.  While I had her on the phone I asked if Mike would itemize the quote.  I also mentioned that they had picked up two or three whole house generator customers through my referrals and perhaps Mike could provide some consideration for that in the pricing.  Next I called Ferman Miller at Countertop Plus in Shipshewana, Indiana to check on the Corian desk top and table.  Ferman answered the phone and said he had called Josh this morning to let him know the pieces were ready for pickup.  I then called Josh to see what his plans were.

We originally agreed that he would pick them up and bring them to our house on his way to visit relatives in the northeast side of the Detroit metropolitan area.  His plans had changed and he won’t be visiting his relatives anytime soon.  He is leaving on Tuesday for a FMCA area rally in the Carolinas and will be gone for a week.  Before he leaves he needs to get something to a customer in Cleveland in addition to getting our stuff to us or deciding that we will have to drive to Shipshewana to get it ourselves.  One option is that we meet him somewhere on Sunday.  Ann Arbor is a possibility but Toledo or Defiance (Ohio) are more likely rendezvous points.

Linda got home around 2 PM and changed into her work clothes.  With Linda’s help I was able to avoid the mess I had with the first hose.  The second hose was even harder to get on than the first one but we managed to do it.  In part because of the arthritis in the joints at the base of my thumbs I do not have as much grip strength as I would like and often need.  The twisting and pushing was hard on my hands and the confines of the base and proximity of crisp wooden edges resulted in lots of small cuts.  This was not something I anticipated in the design and construction of the bases and the installation of the heat exchangers.

I took a break and drove to Northwest Plumbing Supply to see if they had a bleeder valve like the ones in our bus system.  They did not and had never do seen anything like it before.  The showed me a couple of things they did have but I did not buy anything.  I got a call from Brighton Honda that my car was ready for pickup so I headed home to get Linda.  She drove me to the dealership and then went on to Meijer’s for a few grocery items.

I drove to Lowe’s in Howell and was fortunate to find Lars in the plumbing department.  The store was not very busy and he took an interest in showing me various plumbing options that might allow me to replace the bleeder valve with something that would do the same thing while also giving me a way to add antifreeze to the system.  What I ended up with was 3/4″x3/4″X1/2″ copper sweat T and a 1/2″ sweat ball valve with a waste port.

Bruce works on attaching the heater hoses to the fill/bleeder valve T assembly he built.

Bruce works on attaching the heater hoses to the fill/bleeder valve T assembly he built.  (Photo by Linda.)

Back home I cleaned some 3/4″ and 1/2″ copper pipe with 120 grit plumbers sandpaper.  I cut two pieces of the 3/4″ pipe about 3″ long and one piece of the 1/2″ pipe about 1-1/2″ long.  I brushed the inside of all the fittings and test fit the pieces.  I then applied flux to all of the surfaces to be soldered, inserted the two 3/4″ stubs into the run fittings, inserted the 1/2″ stud into the bull fitting, and put the ball valve on the other end of the 1/2″ pipe.  I used the lever on the ball valve to mount the assembly in my bench vise.  I removed the waste port cap to protect the neoprene seal and opened the ball valve so as not to trap heat inside.  I then heated the T and the end of the valve and applied the solder.

I figured there had to be an easier way to get heater hose onto the heat exchanger and that Butch was the guy who would know what it was.  I called and he said antifreeze can obviously be used and works fairly well but that a small amount of dish soap would also work as a lubricant and not harm the antifreeze or the Aqua-Hot and its components.  As long as we were on the phone I caught up on their activities.

They were still there at the RV Park in Bouse, Arizona but only until the 15th of this month.  The terms and conditions of their employment as managers of the park had not turned out to be as described during the interview process and they are wrapping up after only a month on the job.  They will move their bus back to Quartzsite and spend at least part of the winter at Joe and Connie’s place where we both spent last winter.  I know it was a big disappointment to them that the situation in Bouse did not work out, but their situation in Q will be familiar, comfortable, and inexpensive, as well as convenient to the Quartzsite Gem and Mineral Club which they joined this past winter.

For dinner Linda made a blend of onions, garlic, mushrooms, and power greens and served it over a baked potato topped with Daiya cheese.  It was very yummy, and the potatoes kept the dish warm all the way to the end.  The weather had turned cloudy through the afternoon and we got the first raindrops during dinner.

The fill/bleeder valve T assembly with the heater hoses connected. The assembly is located between the bases at the floor and will be hidden by the center connector/cover.

The fill/bleeder valve T assembly with the heater hoses connected. The assembly is located between the bases at the floor and will be hidden by the center connector/cover.

I had really hoped to have the hydronic heating system reassembled today so we went back out to bus after dinner to hook up the heater hose that runs between the two heat exchangers.  This was actually two pieces of hose with my homemade bleeder/fill valve half way between the two exchangers.  Even with dish soap the two hoses were very difficult to get onto the heat exchanger fittings and the bleeder/fill stubs, but I got them on.  Linda took pictures while I grunted, groaned, and moaned and I took a few more when I was done.

It was 8:45 PM when we finally quit working, secured the bus, and went inside.  I cleaned my hands as best I could but I could not get all of the black from the rubber hoses to come off.  We sat for a while in the living room and had the last of the frozen chocolate torte that Linda made a couple of weeks ago.  We finally turned in around 10 PM and watched Rick Steve’s Europe, Travel in the Americas, and a couple of cooking shows while I worked on this post.

 

2015/07/28 (T) Mighty Dremel

Leave a reply

I got up at 8 AM.  I must have been sleeping soundly as I was unaware until then that had already gotten up.  She had gone for a walk and left me a note.  The high temperature today is forecast to hit 90 degrees F and she wanted to get her walk in early.  I fed the cats and checked the mouse trap in the pantry.  We caught another one overnight so I carried the trap back to the northeast corner of the yard and released it.

I made our morning coffee and had just settled in to work on my iPad while it brewed when Linda returned from her walk at 8:35 AM.  We enjoyed our first cup of coffee and then had breakfast.  She made a batch of her fabulous granola yesterday but we have to finish the previous batch first.

Today was the day to get back to work on the bus.  First I spray lubed the two overhead garage doors, both rollers and section hinges, and ran them up and down and back up.  I needed to open them anyway to get out the ladder and tools and sometimes it’s better to spend an extra minute while you are thinking about something and just take care of it.  Besides, I had no way of knowing if I would accomplish anything else today so at least the doors worked more smoothly.

This is where the "stop block" was located. The left screw came out but the right one did not. I had to grind it off.

This is where the “stop block” was located. The left screw came out but the right one did not. I had to grind it off.

In a very real sense our entire bus remodeling project hinges on getting the old refrigerator out and the new refrigerator in.  The refrigerator swap, in turn, hinges on being able to open the fixed window panel on the passenger side of the bus.  That panel is hinged at the top by a pair of rolled channels, one on the top back edge of the window frame and the other on the lower back side of a rail that runs almost the entire length of the bus.  Most of the upper body side panels are hung from these rails and secured at the bottom with latches or other fixed hardware.

The window frame in question has two latches that can be released allowing the frame to swing open and provide an emergency exit, except for the two “stop blocks” in the upper outside corners which are attached to the frame (with two screws) just below the rail.  As the name suggests, these blocks appear to stop the frame from opening more than about 10 inches. That would make emergency escape difficult but it makes it impossible to remove a refrigerator.  We know these frames will open farther as someone posted a photo of an H3 on one of the Prevost bus websites with this same frame open almost 90 degrees (horizontal).

As I have described here before I successfully removed the left block and the left screw from the right block a couple of weeks ago but have been unable to remove the right screw from the right block.  Early in my attempt to remove it I stripped the Philips head and things just got worse from there.  I borrowed an impact screwdriver from Chuck, which successfully extracted the left screw but the right screw would not budge.  I eventually bought and used three different screw extractor sets and broke two drill bits using one of them.

The Dremel with a cutoff wheel installed. The stop block was unusable by the time I got it of.

The Dremel with a cutoff wheel installed. The stop block was unusable by the time I got it of.

I borrowed a soldering gun and Dremel Kit from Chuck on Saturday and finally got around to using them today.  The idea of the soldering gun was to heat the screw causing it to expand and then contract when it cooled.  This will sometimes cause screw threads to separate from tapped holes.  In this case the block was already turning relative to the shaft of the screw but the screw was not turning so I hoped the heat might free it from the threaded hole in the frame.  To find out, however, I needed to create a slot in the shaft that would accept a flat blade screwdriver, in particular the large bit that is part of Chuck’s impact screwdriver kit.  Enter the Dremel.

In order to create a wide enough slot I put two cutoff wheels on the arbor.  The block is at the top of the window frame so standing at the highest safe step of our 8-foot step ladder I was at a comfortable height for holding the Dremel vertically and cutting a horizontal slot.  The cutoff wheels are about the size of a quarter so the slot extended well beyond the screw head, or what was left of it, into the block.  Using the Dremel was a last resort and I knew that once I made that decision the block was going to get destroyed.

The Dremel cutoff wheels cut through the block, which is aluminum, very easily and did not have any trouble with screw or the broken drill bits.  The drill bits eventually loosened to where I was able to extract them with pliers.  I tried several different screwdrivers in my newly created slot but to no avail.  I sprayed WD-40 around the block and screw using paper towels to catch the overspray and clean up any runs.  I kept cutting the block until I was able to pry it off of what remained of the screw.  With less than a quarter inch of the shaft left I cut a slot in the end and tried to unscrew it but the tangs just broke off.  I tried unscrewing it with pliers but it would not budge.  The protruding stub would interfere with opening the frame 90 degrees so I used the Dremel with a cutoff wheel to grind the shaft down flush with the frame.

All the "stuff" I used to attack 25 cents worth of aluminum because of corrosion.

Some of the “stuff” I used to attack 25 cents worth of aluminum because of corrosion.

Linda came out to help at this point.  I repositioned the ladder and then we unlatched the frame on the inside.  Linda pushed it out while I supported it from outside.  It opened farther than it had before but we did not try to raise it to a horizontal position.  The frame/glass is very heavy and we did not want to risk having it come loose at the hinge. We closed the frame and latched it.  I took a few pictures and then put all of the tools away.  The weather was very warm and humid and that was enough outside work for today.

We had hummus, pita chips, and black grapes for lunch.  After lunch I spent a few minutes in my office checking e-mail and then typed up the minutes from our July SLAARC meeting.  I then started working on the design/drawings for the built-in sofa.

I have a very long list of things to do but the furniture design remains a priority as I need to make sure Jarel has all the information he needs to keep moving forward on the custom cabinetry.  Although I will be assembling the sofa Jarel will be cutting all of the pieces.  I will be using a long rip of a full sheet of plywood and a long piece of 3/4 x 3/4 walnut hardwood as an edge band for the horizontal platform.  In order to give Jarel a cut sheet I needed to design the unit.  I also needed to design it so I knew it would fit when assembled.

I took an occasional break to chat with friends on the two local ham radio repeaters that we tend to use but otherwise stayed on task until late afternoon.  I had pulled a book on cryptology from our personal library and started reading it.  I took a nap before dinner and continued reading afterwards.  Fascinating stuff, cryptology.

 

2015/07/24 (F) Open and Shut

Leave a reply

I was up at 7:30 AM and made coffee but I did not see Mara or Linda until after 9 AM.  Around 9 AM I heard a knock at the front library doorwalls and heard someone saying “hello?,  hello?, David?”  I went out the front door and saw the front end of a red Ford Focus parked in front of our bus.  I had never met this guy but he was not unexpected and I knew he was looking for David LaVoisne, who lived here with his wife, Maria, until we bought the house from them in February 2013.  I knew this guy might stop by as he had once before when we were away and chatted briefly with our lawn care guy, Keith.  I also knew that he had worked with David at the Ford Wixom plant before they retired.

We introduced ourselves and had a nice chat.  I explained that David and Maria had sold the house and their Airstream motorhome, bought a newer motorhome, and were now full-time RVers.  (As I recall they bought a used Foretravel.)  Apparently they did not let all of their friends or former colleagues know what they were doing.  I also mentioned that they had moved the few possessions they did not get rid of to their son’s house somewhere in the region and that they probably visited there occasionally.

Mara emerged about the time our visitor left.  Unfortunately I do not recall his name.  We all had breakfast together after which Mara went about her final departure preparations.  She gave Linda a small fir tree and two small herbs.  Linda transferred the herbs to her herb pots and gave Mara’s small pots back.  She needed to top off her fresh water tank so I helped with that.  The lock on the water fill door stuck in the open position so Mara got her can of dry lube and I sprayed a little in the lock by holding the protective cover open with the tip of the key.  That did the trick, another quick fix to a small but potentially annoying problem.

When her rig was basically ready to go Mara made one last use of the shower, got dressed to travel, unplugged the power cord and stowed it away, and pulled in the slides.  After hugs all around she climbed into the pilot’s seat and fired up the engine and Sabra (one of her two cats) climbed up on the dash just in front of the steering wheel.  I guided her as she backed out onto our road.  She drove down to the court, did a three point turn, and a few minutes later drove past our house in the opposite direction, back on the road again after almost two weeks at our place.  It was noon, but she was only going as far as London, Ontario today.  Linda got a text message later letting us know that she had arrived at the Moose Lodge and the border crossing on the Blue Water Bridge from Port Huron, Michigan to Sarnia, Ontario had only taken 30 minutes.

After Mara was out of sight I gathered up the laundry, sorted it, and started a load of warm whites.  I wrote out a list of parts I needed to finish the garage door opener installation and the monitor mounting system in the ham shack and then drove to Lowe’s in Howell.

I was back home by 1:30 PM and we had hummus and chips along with black grapes for lunch.  We started working on the garage door opener installation when my phone signaled that I had a voice message.  It turned out that I had one on the house phone too.  Both messages were from Jarel.  He had a few questions about dimensions on one of desk drawings so I called him back and we sorted that out.  He retrieved the half sheet of walnut veneer plywood from Butch last night and bought 16 board feet of walnut.

In spite of the 85 degree temperature and what felt like high humidity, even though it was only 41%, we worked for about three hours and finished installing the opener on the small garage door.  It was quite an involved process but it worked when we were done.  The new opener has automatic reverse if it encounters an obstruction and an infrared sensor beam about 6″ off the floor.

At 5:30 PM we loaded the old garage door opener into the dump trailer.  We then loaded the old OTA TV antenna pieces.  Brad is picking up the trailer in the morning so we will not fill it but it we put the junk in it that we needed to get out of the garage and a few other things as well.

We took a break around 6 PM to have some water and get off our feet for a while.  At 6:45 PM Linda made salads and cooked up some vegan Italian sausages.  After dinner we planned to work for a while in the ham shack on the installation of the wall-mounted track system but we were too tired to start a project that was going to require decisions and careful attention to detail.  We sat in the living room instead and used our iPads for the usual things.  It was great having Mara here and we look forward to her return someday.  But for now she is off on the next leg of her open-ended adventure and we have a lot of work yet to do to get our bus ready for the 2015-16 winter season.

 

2015/07/11 (S) Impactful Tools

Leave a reply

We had a small crowd for our SLAARC breakfast this morning but good conversation.  After breakfast we drove to Chuck’s house and picked up the manual impact screwdriver.  Barb was up in the thumb visiting her brother-in-law who recently lost his wife (Barb’s sister).  We lingered for a while and then left for home, stopping for gas on the way.

Back at the house I started a load of laundry and then went to work on the stop block screws.  Linda helped steady the ladder and pass tools and parts back and forth.  I got three of the four screws out of the two stop blocks but the head stripped on the forth one so I was only able to remove the aft stop block.  I tried different bits and even tried drilling a small hole in the center of the head to allow the bits to go in farther but it did not work.  The next approach will be a screw extractor, but first I have to go buy one.

We had soy yogurt for lunch with red grapes and I had a few pretzels with roasted red pepper hummus.  I kept trying to get to the basement to work on the desk design but kept getting detoured.  Once I finally reached my office I found that the mouse trap that I had placed under one of my desks was out in front of it.  The food was gone but there was no mouse, only mouse poop.  I realized that the trap was upside down which allowed the door to swing open.  Our best guess is that a mouse was trapped and the cats pulled the trap out from under the desk and accidentally turned it over while pawing at it trying to get the mouse.  Since there was no sign of a mouse having been caught by one of the cats my best guess is that it escaped, for now.

I checked e-mails and found the one with the credentials and instructions for the QTH.com web-hosting of SLAARC.com so I shared those with the other members of the SLAARC website team and then logged in to check out the log file I had created the other day as a test.

I decided to reconnect the Yaesu FTM-400 radio to the Diamond X-50 antenna on the tower so I could monitor the Novi and South Lyon repeaters while I worked in my office.  I had quite a mess on the ham shack desks and decided the best way to deal with it was to install Mike’s Icom IC-2820H in my car in place of our Icom V-8000 2m rig.  At least that would get the 2820 off the desk.  I checked that the mounting brackets and they were identical so I removed the V-8000 but left the mounting bracket installed in the car.

Mike had modified the power cord on his radio by cutting off the T-connector and replacing it with Andersen PowerPoles so I had to modify the power cable in my car to match as I could not modify Mike’s radio.  I removed the fuse from the positive (+12VDC) lead and then cut off the T-connector, leaving about 6″ of wire so I can add PowerPoles and make it into an adapter cable.  I brought my Hakko soldering station up from the basement, set it up on the floor behind the center console, ran an extension cord from the garage, and used it to solder PowerPole contacts to the two wires.  I then inserted them into the black/red housing pair and snapped them in place.

I mounted the IC-2820H, connected the power cable and connected the coax from the antenna.  I reinstalled the fuse in the positive lead, started the engine, and turned the radio on.  A couple of hams were chatting on the Novi repeater, one of whom I knew (Jim, KB8TAV).  When they finished I gave Jim a call and he came back to me, the first time I have been able to use the Novi 440 repeater from my car.  Jim signed off and I switched to the South Lyon 2m repeater and gave a general call.  Steve (N8AR) came back to me and we had a short QSO that verified the radio/antenna was also working on 2m.  As we were wrapping up Linda started fixing dinner.

Linda fixed a simple salad and Dr. Praeger’s vegan hamburgers with Daiya non-dairy cheese.  These patties were also squishy rather than firm and, like the ones at Zingerman’s Roadhouse the other night, where not very satisfying.  They tasted OK, and we ate them because we are not inclined to waste food, but there is a lot more to what makes food satisfying than just taste.  Sight, smell, and texture (mouth feel) are also important.

Linda had several TXT messages from Mara letting us know that she would be arriving tomorrow sometime before 2 PM as she wanted to watch the Wimbledon finals at that time.  Linda and I considered how best to accommodate Mara’s motorhome and finally decided to just pull our bus straight forward until the nose was at the edge of the concrete driveway.  That created more than enough space on the level part of the pull-through driveway for her to park and plug in to our 50 amp service.  The only loads we have in the bus at the moment are battery chargers so we used our 15 amp cord to plug it into a garage outlet.  Since I had to start it to move I switched it to high idle once I had it positioned, leveled it, turned on the OTR air-conditioning to put a load on the engine, and let it run for 30 minutes.

I returned to my office after dinner and work on the desk design for a while but by this point I was tired and not really in the mood.  The last time I updated the BCM page on our website was after the February 2015 issue came out.  I have had articles in the March, April, and May issues and will have articles in the June and July issues.  I captured the covers from March, April, and May and updated the page.

I exchanged e-mails with several people and spent some time looking at dual and triple monitor stands on EBay.  We rarely use EBay and the site made me change our password before it would let me log in.  There was a large selection of products but none of them were exactly what I am looking for.  There wasn’t any rush so I decided to revisit this tomorrow.

 

2015/06/30 (T) Three Score and Five

Leave a reply

Today was a milestone birthday for Linda.  We had our usual leisurely early morning with coffee, fresh fruit, and cinnamon raisin toast (from Metropolitan Baking) for breakfast.  We talked some more about our long-term ham radio plans and decided we would order one (1) of the new Yaesu FTM-400DR/DE dual band mobile radios and a slightly more powerful VHF/UHF base station antenna.  Our daughter called around 9 AM to wish her many happy returns of the day.  My Michigan Public School Employee Retirement System (MPSERS) health insurance shifted her to secondary, with Medicare as primary on June 1st, the first day of the month in which she turned 65.

The temperature was in the low 60’s when we got up at 6:30 AM.  The weather forecast for the afternoon had an increasing chance of rain and the possibility of isolated thunderstorms so Linda went for a mid-morning walk.  I headed to my office to order the radio and a Diamond X-300NA 2m/70cm antenna.  All of the online distributors are selling the radio for the same price.  I decided to buy both products plus the RTSystems programming software, from Amateur Electronic Supply (AES).  Their UPS Ground shipping is “free” and since they are based in Ohio the shipment will be here in 1-2 days rather than 4-5 days.

I took a break and spread three more bags of brick pieces around the base of the tower and in front of the cable entry box.  Back in my office I dealt with some personal e-mail.  I sent an e-mail to Scott (KE9FOX) at QTH.com with additional information he needed to transfer the SLAARC website and domain name registration from GoDaddy to QTH.com.  I then gathered up a load of laundry and put it in the washer.

By the time that was all done it was getting close to lunch time.  Lunch was a big spinach and lettuce salad, baby carrots, a few sourdough pretzel nibblers with roasted red pepper hummus, fresh sweet cherries, and the blueberries/strawberries/raspberries that were left from breakfast.

After lunch I transferred the laundry to the clothes dryer and then got cleaned up.  We left around 3 PM for the U.S. Bar and Grill in Wayne and stopped on the way to get a card.  Today was John Smallwood’s last day at Wayne RESA and there was a gathering from 3-to-6 PM to see him off.  John was the VP of the Wayne County Salaried Staff Federation (WCSSF) and succeeded me as President of the local when I retired.  Now it was John’s turn to enjoy a well-earned and well-deserved retirement.  This was the second gathering for a colleague in the span of just over a month.  Besides wishing John well it was an opportunity to reconnect with other former colleagues.

After a suitable amount of time visiting at John’s party Linda and I drove to the Mongolian Barbecue in Novi for a celebratory birthday dinner.  It is a very noisy restaurant but was not as bad on a Tuesday evening as it was the last time we were here on a Saturday.  I would have preferred a quieter and more relaxing atmosphere, but the Mongolian Barbecues have a lot of ingredients that we can eat and we find the method of preparation very much to our liking.  By the time we had a small bowl of soup, a moderate sized salad, and a good size bowl of ingredients we were full.

I had a brief QSO with Chris (K8VJ) on the drive home.  I stopped at the Shell station and topped off the gas tank in my car so we would be ready to go in the morning.  We finally got home at 8:30 PM.  Linda made some hot tea and we each had a piece of Prickly Pear Cactus Jellied Candy.  I restarted the dryer on Touch Up and checked my e-mail.  We were tucked in by 10 PM as we needed to be on the road by 7:30 AM tomorrow.