Tag Archives: Rick (ISRI USA)

2015/06/29 (M) Website On The Air

Leave a reply

Linda was up at 5:55 AM this morning and left for the bakery at 6:15.  Experience has shown that this is usually early enough to get ahead of the morning rush hour traffic inbound to the Detroit metro area from the northwest.

I got up about an hour later, had granola for breakfast, and enjoyed my morning coffee (Sweet Seattle Dreams half-caff blend from Teeko’s) and then made a run to Lowe’s to purchase a couple of copper ground lugs and 5 feet of #10 green ground wire.  Back home I tried to use one of the ground lugs to terminate the ground wire from the cable entry box (CEB) to the 36″ ground bar on the wall behind the ham radio desks but it’s shape prevented the wing nut from going onto the stud.

I planned to use the other lug to attach one end of the #10 wire to the ground bar and put a male spade lug on the other end to mate with the connector on the Go Box ground pigtail, but that clearly was not going to work.  I dressed the ground wire and (temporary) coax in the ham shack and put the ceiling tile back in place.  I then started cleaning up the living room and small bedroom per Linda’s request before she left this morning.  Some of our (my) projects have a way of expanding throughout the whole house.  I had hoped to also pick up the coax cables spread out in the recreation room, and at least start to straighten up the ham shack/office, putting materials away and moving tools to the garage.

At 10 AM I made a few phone calls.  The first was to Rick Short at ISRI USA regarding the 6860 bus driver’s seat and a possible visit tomorrow morning.  I got his voice mail (again) and never got a return call (again) so I gave up on getting any assistance from him or from ISRI USA.  I called Linda to make sure she did not have any commitments on Wednesday and then called Josh at Coach Supply Direct to set up a visit to his shop for Wednesday late morning.  Linda and I plan to finalize our Flexsteel furniture order and give Josh the deposit during that visit.  Next I called Scott Adams, AC8IL, at Adams Electronics and ordered a 20 foot length of LMR-400 with an N-male connector on one end and a PL-259 connector on the other end.  Scotty and I also chatted briefly about tower bases.

I e-mailed Scott Neader at QST.com regarding the transfer of the SLAARC domain name and website from GoDaddy to QST.com and got a reply back right away with an outline of the steps I needed to follow.  First on the list was creating an account for our ham radio club through his billing system.  I took care of that and e-mailed him back.

Keith Kish, from Kish Lawn, care showed up around 11 AM to cut the grass.  When he was done I headed back to Lowe’s to look for an alternate ground clamp and pulley support for the tower but did not find anything suitable.  So as not to have it be a wasted trip I bought three more bags of broken brick pieces to use around the tower base and cable entry box.

I spent some time looking at the Yaesu FTM-400DR/DE on several different ham radio equipment vendor websites.  Yaesu is offering a $100 rebate on this 2m/440 mobile radio through tomorrow.  All of the distributors are selling it for the same price, $599.95 and the rebate brings it down to $499.95, so if I buy one it will come down to who has them in stock and is offering free shipping.

Linda got home from the bakery around 3 PM, earlier than I expected and nice for her.  She went for a walk while I continued to fuss with ham radio and website stuff.

For dinner Linda made a white beans and mustard greens dish.  We eat a lot of lettuce, kale, and spinach, both raw and cooked into dishes, but only occasionally have collard greens or mustard greens.  Mustard greens have a very strong, bitter flavor and I liked them more than Linda did.  I think they are an acquired taste and may be more suitable as an accent ingredient rather than a main one.

After dinner I checked my e-mail and had a reply from Scott at QTH.com.  The QTH SLAARC account invoice was ready so I paid it using a personal credit card.  I then moved the coax from our Icom IC-7000 to Mike’s Icom IC-2820H and turned it on.  Mike was on the South Lyon repeater discussing the Field Day event with Steve (N8AR) and Bruce (W8RA).  Paul (N8BHT) was able to join the conversation but I was not successful breaking in so I just listened.  It was an indication that my power into the repeater was probably still marginal but a good reminder that ham radio conversations are very public.

When they were done I called for Mike and he came back.  We had a good QSO (chat) about the Yaesu FTM-400.  Jim (N8KUE) joined in for a while.  After Jim dropped off we tested my ability to transmit to, and receive from, both the South Lyon 2m and Novi 70cm repeaters.  The added power of the IC-2820H over my IC-7000 (50W vs 35W in the 70cm band) combined with the lower signal loss of the better coax made just enough difference that I could hold the Novi repeater when transmitting although my signal was still on top of a lot of noise coming back out of the repeater.

Linda wanted to watch an episode of Scorpion, followed by NCIS Los Angeles, after which I caught an episode of Two and a Half Men and then turned off the TV.  I will have to make a decision about the Yaesu FTM-400 in the morning.

 

2015/06/25 (R) The Mouse

Leave a reply

Brighton Honda called yesterday in the afternoon to get permission to do additional work on my car.  Since we plan to keep the car for a while, and then perhaps give it to our son, it was the kind of work that needed to be done regardless of the costs.  They called back later to indicate that they would not have it aligned before closing time.  That was fine with us as it would have been inconvenient to impossible for us to get there by 6 PM to pick it up.  Linda told them to call in the morning when it was ready.

The top of the 40-foot tower from the WNW showing all of the antennas and the pulley with the haul rope. The weather had definitely deteriorated from the day before.

The top of the 40-foot tower from the WNW showing all of the antennas and the pulley with the haul rope. The weather had definitely deteriorated from the day before.

It is amazing how attuned we become to routine sounds and how sensitive we are to non-routine ones, even (especially?) while sleeping.  So it was last night that I was suddenly aware that one of our cats was making a repetitive sound that was unusual.  I turned on my flashlight, hoping to not disturb Linda, and got out of bed.  Both cats were hunched down on the floor on Linda’s side of the bed with Jasper in front.  He was the one responsible for the sound and the reason was next to his head and about 3 inches away; a little dark gray mouse.

My first thought when I see one or both of the cats with a mouse next to them rather than in their mouth is that it is dead but that was not the case.  This mouse was alive and apparently not injured.  I have seen this behavior before in which the mouse basically “plays dead” and the cats leave it alone but watch it carefully.  Mice seem to know that cats are triggered by movement and that if they sit very still the cats just sit there and guard them.  It was 4:30 AM and I was not fully awake so I do not recall the exact sequence of events, but the mouse somehow ended up in our master bathroom.   I do not recall what I did with the cats but I think I went and got a box with high sides and tried to get the mouse to go in it and it made a run for it towards the bathroom.  Linda was awake by this point so she got a towel for me.  I went in the bathroom and used the towel to block the gap under the door and prevent the little critter from getting back into the bedroom while I tried to get it into the box.  I was unsuccessful and it managed to find a place to hide in the hot water baseboard radiator.

Linda got one of the live traps we recently purchased and baited it with the recommended saltine and peanut butter.  We set the trap near the radiator, turned out the bathroom light, shut the door, and tried to plug the gap with the towel from the outside, figuring we would deal with the mouse in the morning.  Juniper kept pawing at the towel and pulling it back from the door so we put both cats out of the bedroom and shut the door.  They found that confusing as they sleep with us and generally have the run of the house.  One or both of them pawed at the door meowing to get back in for quite a while.  It wasn’t the best night’s sleep we have had and the timing was unfortunate given the hard day of tower work.

Brighton Honda called at 8:01 AM to let us know the car was ready.  Hello, I’m awake now!  I checked on the mouse and it was now safely tucked away on top of the radiator fins inside the housing where neither the cats nor I could get to it.  We decided to leave the live trap in place, sealed the gap under the door, and kept the bedroom door shut to keep the cats out.

I had planned to drive to Isringhausen’s U.S. headquarters in Galesburg, Michigan today but first we had to get my car.  As long as we were headed that way we decided to go to the Brighton Panera for coffee, but had toast and juice for breakfast at home before we left.

The 100,000 mile service is extensive and includes changing the spark plugs.  Beyond the routine service items the Element needed a new ball joint and tie rod and had a stuck brake caliper pin that had to be repaired.  Given the front end work I also had them align it.  Butch and I rebuilt the front brakes last year so I was surprised that there was an issue with them, but the car has been towed and driven in some harsh environments since then so that may have been a factor.

The Panera at Grand River Avenue and I-96 is not one of our favorites.  More often than not we end up with coffee grounds in our cups and the bathrooms are not maintained as they should be.  Today was not the first time we have been to this location that the men’s restroom was out of toilet paper.  It is also often freezing cold inside the restaurant and today was no exception.  The weather was overcast and a bit gloomy but the outside temperature, while not warm, was much more comfortable than inside.  We were also unable to connect to their Wi-Fi signal, which is generally useable.  That’s pretty basic stuff to not be able to get right and falls squarely on local management in my opinion.

While we drank our coffee I called Rick Short at ISRI to make sure he would be in but I got his voice mail again.  I asked for a call back but never got one so I did not make the trip to Galesburg.  Apparently they have better things to do than be of assistance to me.  I only want to buy one chair, not a fleet of chairs, so I understand my relative unimportance, but I don’t like it just the same.  We decided to spend the day at home completing the work from yesterday, which had made a mess throughout the house.

One of the things we needed to do was register our cellular booster system.  Given that it is a five band device I was not clear on whether we had to register it only with Verizon or with all of the carriers.  I called the company we bought it from, Cellular Solutions, and talked to Judy who said we only had to register it with the carriers we personally use.  For us that is Verizon Wireless.  Registration was via the Verizon Website and was simple enough.  It did, however, require me to log in to our My Verizon account and navigate through a couple of screens to a page where we could enter the information from the label on the box.  The serial number was on two peel off tags, so one of those went on the booster and the other one went in the manual.

With the unit registered I turned the power switch on and watched the ‘Alert’ lights all go solid yellow.  As I mentioned in yesterday’s post solid yellow lights are not described anywhere in the manual.  I called Cellular Solutions back and said I had a technical support question.  The woman on the phone took my name and number and said someone would call me back.

Since I was apparently taking care of phone chores I decided to call Universal Towers and inquire about their B-30 base.  The woman who answered the phone never gave her name but was able to answer some questions.  She indicated that their base might or might not be compatible with older Heights Tower products, depending on exactly which product I had, and that I would have to talk to the owner, Bill, who wasn’t there at the moment.  She did know that the outside-to-outside measurement of the legs on a B-30 base was 30 inches and the base cost $290.  She also told me that the larger bases, like the B-30, consisted only of the three rods with the mounting yokes on top; the three rods were not otherwise connected together in any way.  She also confirmed that the ‘U’ shaped yokes at the top of the base rods were welded on and not adjustable.  The normal installation procedure involved connecting them to the bottom of the legs of the first section of the tower, setting them in the hole as the concrete is poured, and adjusting them by moving them around until the legs of the tower were plumb.  That sounded to me like a process where a lot could go wrong and not be repairable.

I pulled a 75 ohm coax out of the ceiling of the basement yesterday.  We laid it out in the basement to see how long it was and it looked to be at least 60 feet.  Linda suggested we test it before running it through the basement ceiling which was a very sensible idea.  I unplugged the power adapter for the TV amplifier power inserter, detached the coax that feeds the TV in the bedroom, attached the downstairs cable, and connected the other end to the basement TV set.  Linda set up the TV for Antenna input, did an All Channels scan, and got the same stations we got yesterday, minus a couple.

In spite of what appeared to be acceptable performance I decided I wanted a new coax cable and Linda wanted to return three of the ropes I bought at Lowe’s but never used.  She found the receipt and we went to Lowe’s.  They had a good quality RG-6 quad-shield coax (75 ohm) in various lengths including 50 feet, which is what I needed.  At the register I decided to buy two more 40 pound bags of solar salt.  I am not an impulse shopper as a rule but their supply of Morton Solar Salt was very low and stocking up seemed like a good idea.

We stopped at Teeko’s to order coffee.  Mary took our order and rang it up; one pound each of the three different half-caff blends that have become our standard.  We took note of the fact that the Bennigan’s restaurant building on the northwest corner of Grand River Avenue and Latson Road was gone and a sign said a Panera would be coming soon to that location.  We didn’t say anything to Mary, but that cannot be good news for Teeko’s.  We will continue to buy our custom roasted beans at Teeko’s as long as they are open but it is going to be difficult for them to compete with a $2.25 cup of bottomless coffee, free Wi-Fi, a restaurant, a bakery, drive through service, and ample parking with great access to I-96.

When we got home I checked the live trap in our master bathroom and we had captured the mouse.  We took the trap to the northeast corner of the property, towards our neighbor’s pond, and set it free.  It did not want to leave the trap and I had to encourage it to go.  Once it hit the ground, however, it scampered away looking for a place to hide.

We then worked on running the new coax from the basement TV to the sump pump room above the suspended ceiling.  I disconnected the power inserter for the amplifier and disconnected the old coax we had tested earlier.  I notched a ceiling panel at the corner of a boxed support column behind the basement TV to allow the ceiling tile to go back into place around the coax.  We then installed one of the wire channels to contain and hide the coax from the ceiling down to the TV set and connected it to the back of the set.

In the sump pump room I attached the coax from the cable entry box (CEB) to the input of the new 1-to-2 signal splitter.  I attached the coax for the bedroom TV to one output from the splitter and the coax we just ran to the other output.  I mounted the splitter on the wall of the sump pump room and secured the cable coming from the CEB to the ceiling.  I then plugged the power supply for the power inserter back in to an AC outlet.  Linda scanned for channels and verified that everything was working correctly.  We then installed the other wire channel alongside the trim on the bedroom doorwall to route and hide the cable coming up from the basement.

I continued to fuss with the cell phone booster gain settings.  We had not gotten the promised return phone call from Cellular Solutions Technical Support so I called them.  I got Judy again and explained what I was seeing with the solid yellow lights.  She checked with her tech support people and they said the manufacturer (SureCall) told them the solid yellow was the same as the blinking yellow; that the booster was adjusting the gain and it was “normal.”  The manual says that normal is when the light is off, so I’m not sure I buy this explanation, but based on that I left the booster turned on.

With all of that done we started cleaning up the tools and materials we had scattered over two floors of the house.  I decided that was also a good time to start a load of laundry, although it was actually rather late in day for that.  I did three loads by the time I was done and it was sometime after 10:30 PM before the last load was dry.  I needed to be up at 7 AM to be at breakfast in South Lyon at 8 AM as our SLAARC group would start setting up for the ARRL Field Day event at 9 AM.

 

2015/06/23 (T) Grounded

Leave a reply

As I wrote in yesterday’s post we did not turn off the lights last night until almost 1 AM because we were keeping a close eye on the weather moving across the lower portion of Michigan’s Lower Peninsula.  Although strong to severe storms were still forecast from 1 AM to 5 AM they either did materialize at our exact location or we slept through them.  We had the house closed up and the air-conditioning on, so that cut down the sound level of outside noises.

A cold front had pushed through by sun up and we woke to a cool morning with blue skies and noticeably lower humidity.  We did not have any trees, or even big limbs, come down and there was no damage to our brand new roof.  The forecast yesterday was threatening enough, however, that in the morning we took the potted plants, and as much of our outside lawn furniture as we could find room for, inside including our sun umbrella and trash cans.  I planned to be gone most of the day, and Linda was leaving mid-afternoon to go to dinner and a movie with Diane Rauch, so our first chore was to put all the lawn furniture, plants, and other outdoor stuff back outdoors.

This week is mostly being devoted to ham radio with the ARRL Field Day as the crowning event this weekend.  My specific focus for most of the week, however, has been the “communications tower” adjacent to the east wall of our house.  As described in previous posts we installed a cable entry box (CEB), mounted the cellular booster in the basement, mounted the inside cellular antenna, and ran coax cables.  The antennas will (hopefully) be mounted on the existing 40 foot tower tomorrow, cabled into the CEB, and cables run from there to devices inside the house.  With any luck by the end of the day tomorrow we will have decent cellular service inside the whole house, the ability to watch OTA TV programs on two different TV sets, and finally be able to connect one of our radios in the ham shack to an antenna.  Today, however, was planned to mostly address other things.

I had an appointment with our dentist at 10:20 this morning and left at 9 AM.  I planned to stop at Chuck’s bus garage and check that the key he lent me worked, but I needed gas for my car.  I did not have time for both and did not really have a choice; I would have to check the key some other time.  I ordered two cables yesterday from Scott (AC8IL) at Adams Electronics.  Later in the evening I was unsure if I had specified the connectors correctly so I called and left a message.  I called again this morning to make sure the message got through.  It did, and my original connector specifications were correct.

I arrived at the dentist’s office about 10 minutes before my appointment time.  I called Rick Short at Isringhausen USA to make sure he was going to be in before I drove two hours to Galesburg, Michigan after my dentist appointment.  I got his voice mail a left a message.  “ISRI” makes very high tech air suspension driver’s seats that are used as original equipment in motorcoaches, semi-tractors, heavy equipment, and locomotives.  I would really like one for our bus, but it is not proving easy to get.

Dr. Steve and his assistant, Leslie, made molds of my upper and lower teeth and a bite impression.  The molds will be used to make a mouth guard that I can wear while I sleep.  Dr. Steve has a strong suspicion that I am clenching my teeth and the mouth guard will reduce or eliminate the irritation it causes.  I will have to ask if I can wear it during the day too as I am occasionally aware of clenching my teeth while I awake.

I had not heard back from Rick by the end of my appointment so I called the main number at ISRI and talked to the receptionist.  It turned out that Rick was not in today and she transferred me to Jeff Woodworth.  Jeff was willing to meet with me but thought it would be a better use of my time to wait until Rick was available.  My next opportunity to drive to Galesburg will be Thursday and I will likely go as the ISRI seat is holding up our ordering of Flexsteel seats through Coach Supply Direct.

I stopped for coffee and then re-routed for Chuck’s bus garage in Novi.  The key to the garage worked perfectly.  I called Linda to let her know about the change in plans and headed for home.  There is too much to do at the moment to waste much time so I installed the #4 AWG bare copper ground wire I bought yesterday at Lowe’s.  I mounted an offset copper wire lug using the center support stud for the copper back plane in the CEB.  I replaced one of the plastic hole plugs with a rubber plug with a small hole in the center.  The hole I chose in the bottom of the CEB allowed the ground wire to come straight up into the lug.

Another view of the cable entry box on the east end of the house by the 40-foot tower.

Another view of the cable entry box on the east end of the house by the 40-foot tower showing the bare copper ground wire that runs to the ground rod and then to one of the tower legs.

Outside the CEB I routed the ground wire around to the existing ground rod and secured it using the new clamp I bought yesterday.  There was an old ground wire connected from a clamp on the tower to the ground rod.  I removed that wire along with some coax and control wires that I had clipped when we removed the old satellite dish.  I then attached the new ground wire to the clamp on the tower.  While we were at it Linda trimmed back a small bush that was growing between the tower legs and I pulled leaves, grass and other stuff out from around the Day Lilies that we transplanted last year around the tower base.

With the CEB grounded we looked at how we might get a video cable up to the TV/monitor in our bedroom.  The wall where the TV is mounted has a hot water baseboard radiator that comes almost to the trim on the door wall.  That end of the radiator has a copper pipe that goes through the floor into the basement and it was easy to locate the pipe in the basement.  I determined that there was enough space behind the pipe to safely drill a hole but I had to drill it from the top side at an angle.  A 5/8″ wood boring drill bit created a hole just big enough for the molded F-connector on the end of the cable to pass through.

We fed the video coax cable above the suspended ceiling in the ham shack area to the location of the hole.  I then fed the cable up from the basement as Linda pulled it up into the bedroom.  We adjusted the amount of cable in the bedroom to allow the wall mounted TV set to move through its entire range of motion.  The other end of the cable was then routed into the sump pump room.

By the time we finished pulling this cable it was 3:30 PM and time for Linda to leave to pick up Diane.  They were headed to Royal Oak for dinner and a movie as the movie they wanted to see was only showing at the Royal Oak Main Theater.

While I was out during the morning Lynch Carpet had called to let us know our Armstrong vinyl tile was available for pickup so after Linda left I closed up the house and went to get it.  The 12 boxes of tiles, container of vinyl adhesive, and container of vinyl grout were all neatly arranged on a small pallet and tightly wrapped in shipping plastic.  Rather than break this down and load each thing individually they used a fork lift to set the pallet in the back of my Honda Element.  The rear suspension settled at least two inches when they transferred the full weight of the pallet to the floor of my car.

When I got back to the house I backed the car up to the garage.  I cut the shipping plastic loose and unloaded the tubs and boxes of tiles.  I put the pallet on the garage floor and then neatly stacked the boxes of tiles on it to keep them off the floor.  Each box contained 14 tiles measuring 16″ by 16″ for a total area of 24.89 square feet.  The Armstrong Alterna tiles are a “luxury vinyl” product, and are about 1/8″ thick.  Even so, the boxes were heavier than I expected so I decided to weigh one.  It tipped the scale at just under 42 pounds.  That meant the entire pallet weighed close to 500 pounds, and, ignoring the weight of the cardboard box, that is about 3 pounds per tile.

When I drew out the design I determined that I would need 158 tiles, some of which would be partial.  Figuring conservatively at 150 full tiles equivalent, and ignoring the weight of the underlayment, adhesive, and grout, the floor tiles will weigh about 450 pounds.  I have no idea what the carpet and ceramic tile that I have removed weighed but the tiles were heavy.  I also have no idea what the furniture weighed that we have removed but also have no idea what the new furniture will weigh.  The intent was that the new floor and furniture would weigh less than old stuff but we will see.

I traded phone calls with my dad and we finally got to talk for a half hour starting at 4:30 PM.  He turned 90 this past Sunday.  Mike Fearer from Bid-Rite Concrete called at 6 PM and arrived about 10 minutes later to discuss the foundation for our 70 foot ham radio tower.  I had printed off a page from the Universal Tower website showing their tower base.  I also downloaded and printed their base and tower installation instructions.  I had a set of these to give to Mike so he would have some idea of what the project is about.  We looked at the proposed location for the tower and access for his dump cart.  We also talked about the base, a rebar cage, a form around the top of the hole to allow the concrete to be slightly above ground, and a jig to make sure the base is level and the tower is plumb.

He said he was interested in the job and would work with me and Phil Jarrell (the excavator) to get it done.  Rather than bid the job he would just do it for time and materials.  He also said the current price of concrete was about $100 per cubic yard.  We will need about six (6) cubic yards to fill the required 5′ x 5′ x 6′ (deep) hole.  He thought he might be available the middle of next week but I don’t think I could have everything pulled together that quickly.

After Mike left I went to Lowe’s and picked up five 40 pound bags of topsoil, a 1-in/2-out signal splitter (rated for 5 MHz to 2.4 GHz), and a plastic snap cover channel for hiding the video cable we ran up into the bedroom from the basement for the TV set.  I then went to the Meijer’s supermarket just across Grand River Avenue for soy creamer but they did not have what I was looking for.  As long as I was there I had a salad for dinner at the in-store Subway.

While I was sitting there I called Mike Sharpe (W8XH) to confirm that he was available tomorrow to help with the antenna installations on our 40 foot tower.  I mentioned that the only thing I lacked was a standoff with a pulley at the end of it for hoisting stuff up to me.  He suggested that something like that was essential and I agreed, so I headed back to Lowe’s to see what I could figure out.  What I ended up with was a three foot long 7/16-14 threaded rod, a pulley that had a closed eyelet on top (and was big enough for the 3/8ths rope I bought), some 7/16ths washers, and some 7/16-14 nuts.

When I got back to the house I unloaded the topsoil near the part of the east yard that needs to be filled in, took the other stuff inside, and then assembled the threaded rod pulley system.  I secured the pulley on one end of the rod using two of the nuts, one on either side of the eyelet.  I threaded a nut onto the other end, put on two washers, two nuts, two more washers, and another nut.  I ran the first two nuts, with two washers between them, part way down the rod.  I left the second pair of nuts, with washers between them, near the end of the rod.

I took the assembly out to the tower and adjusted the position and spacing of the two pairs of nuts and washers so they would bracket two of the horizontal tower members.  In use I will secure the rod to the tower at each pair of nuts/washers using plastic cable ties.  This arrangement will put the pulley at least 18″ from the tower which should be far enough out that we can hoist the DB8e OTA TV antenna to the top of the tower without it banging into the tower or hanging up on something.  This antenna is the largest thing we need to hoist up. The old TV antenna is considerably larger and heavier, but it is coming down via gravity.

There was a message on our answering machine from Linda’s sister, Sr. Marilyn, who lives in St. Louis.  She was listening to the news earlier today about the storms that went through our part of Michigan and wanted to make sure we were all OK.  By the time we finished talking it was dark and I was done working for the day.  Linda called shortly thereafter to let me know she was on her way home and I mentioned the call with Marilyn.

I finally opened the box with the vertical omnidirectional outside antenna for the cellular booster system and discovered that I should have opened it sooner.  The mounting bracket was designed to be mounted to a vertical surface, such as the side of a house, not a tube, such as a tower leg.  I did not want to postpone tomorrow’s tower work so I will have to get up early and figure out a way to adapt the existing bracket so I can mount the antenna to the top of the tower.

My initial thought was that an aluminum U-channel of the correct size might solve the problem very nicely.  I could drill two holes in the bottom of the “U” to match the two holes in the bracket.  I could then drill three pairs of holes through the sides of the channel.  The antenna would be bolted to the bottom of the channel.  With the open part of the channel held against a vertical tube I could secure it with three long plastic cable (zip) ties.  Conceptually it should work and be easy to fabricate, but will take time which I won’t have a lot of in the morning.  We have to get the two coax cables from Scotty (AC8IL), drop off my car at Brighton Honda for its 100,000 mile service, and be back in time to have the mount fabricated and all of the antennas and tools ready to go by 10:30 AM when Mike shows up.

Linda got home at 9:45 PM, earlier than she thought she would when she left.  She and Diane ate at Luigi’s and had a very nice meal.  They also enjoyed the movie.  We had a big day on tap for tomorrow and we asleep by 10:30 PM.

 

2015/06/08 (M) Home for a While

Leave a reply

It rained until well after midnight last night.  The rain was not steady but more in the form of heavy downpours associated with thunderstorms.  The gutter along the rear of our house was not able to handle the volume of water and it was spilling over onto our deck making a sound that we are not used to.  I noted that I should check the gutters for clogs at the downspouts today.  My phone chirped, which meant I had an e-mail, and I presumed it was from our whole house generator.  When I got up this morning the clocks on the microwave and range were flashing “2:06”, so my first thought was that we must have taken a power hit then, but the messages on my phone indicated that utility power had been lost and restored around 3:45 AM; at least that was the date/time stamp on the e-mails.  I got up just before 6 AM and finally figured out that the clocks probably reset to 00:00 when the power blipped (3:45 AM + 2:06 elapsed time = 5:51 AM).

I sat in the living room writing with my iPad and playing games until a little after 7 AM and then made coffee, which got Linda out of bed.  We had planned to empty out more of the bus today but the weather was gloomy and we were tired from the rally so we had a long, leisurely morning before busying ourselves with inside chores.  Linda worked at her desk and I wasn’t in the humor to work downstairs in my office so I set my computer up on the dining room table.  Other than an occasional trip to the bus or the garage I mostly sat in front of my computer and talked on the phone all day.

Linda called Alchin’s, our regular trash collection company, to see if they would pick up the old RV furniture.  They do not have a special truck they can send and could not take the steel furniture even if they could get it into their garbage truck.  Linda suggested we find a company like “Got Junk” and searched online for one in the area.  We decided to call “Chuck It Junk Removal” as they are located relatively close to our house.  Keith, from Kish Lawn Care, showed up around 11 AM to cut the grass and Brad, from Chuck It Junk Removal, showed up around 12:45 PM to look at the furniture and flooring we pulled out of the bus and give us a quote on the cost to haul it away.  As Keith was finishing mowing the grass dark clouds were rolling in from the west and not long after he left we had more rain, although nothing like last night.

My dentist thinks my current intermittent teeth issues are the result of clenching my teeth at night so I made an appointment to get fitted for a mouth guard to wear while sleeping.  I also got hold of Phil Jarrell and he decided that tomorrow morning at 8 AM would be a good time for him to stop by and take some elevation readings for the driveway extension and a French drain for the far west end of the property.  Besides the obvious economy of having him do both jobs while he is on site, we need a place to put the topsoil he will dig out for the driveway and we need topsoil to fill in low spots on the west end of the yard.

I managed to finally get some orders placed today.  The big one was for a SureCall Fusion5s multi-band cell phone booster (transceiver) system from Cellular Solutions in Mt. Pleasant, Michigan.  The other was for a window seal from Prevost.  This is not the seal that holds the glass in the frame but rather a large rubber part that seals the space between the window frame and the structure of the coach.  We may need to unlatch the large fixed window on the passenger side and use it to get the old refrigerator out and the new one in.  This window frame has not been opened since we bought the bus and may not have been opened for many years before that, possibly not ever since the bus was built.  I want the new seal on hand in case the current one gets damaged trying to open the window frame.

Besides these two purchases I talked to someone at A-1 Upholstery and described our home made sofa plans.  She suggested that we would need ~9 yards of 54″ wide material for the sofa seats and back cushions.  I sent an e-mail to Josh at Coach Supply Direct reminding him of some things we had discussed at the rally last week and Rick Short at Isringhausen with questions about their 6800 series bus driver seats.  I also finally got to talk to Mike at Suburban Seating in New Jersey.  As I suspected we cannot buy the seat directly from ISRI, but I may be able to order it through Suburban Seating and pick it up from ISRI USA in Galesburg, Michigan.  That would be much nicer than having it shipped to our house on a truck from New Jersey.

I called Rupes/Cyclo to try to get answers to a few questions about the Cyclo 5-Pro Mark II Dual Head Orbital Polisher and its various pads but could not figure out how to talk to a real person.  I submitted the online Contact Form with my questions and got a speedy reply from Cory as a result of which I now know what to order.  All I have to do is figure out how many of each thing I need.  The Cyclo 5 is available on Amazon Prime, by itself, but it did not appear to be the Mark II model.  Some of the major distributors claim to give you a set of “free” ProGuard Orbital Backing Plates, but the Rupes/Cyclo website clearly states that the polisher is not sold without one of the three head options.  I prefer not to patronize businesses that misrepresent their offerings and will probably order the polisher, pads, and chemicals directly from Cyclo even if I am paying MSRP.

I got a call from Gary Hatt at Bus Conversion Magazine.  I had not looked at or replied to e-mails in over a week and he wanted to make sure everything was OK.  While we were talking we got a call from Curtis Coleman of RVillage so Linda took that initially until my other call was concluded.  I had e-mailed Curtis earlier in the day and he was responding to that communique.

Somewhere in the middle of all that we had chickpea salad on a bed of greens for lunch.  Linda then went for a walk, met Chris (K8VJ) at Lowe’s to pick up some SLAARC mail, and roasted vegetables for our dinner when she got home.  I sent Chuck Spera a short e-mail inquiring about how to open the latches on our emergency escape window and then called it a night.