Tag Archives: Refrigerator (H3-40)

2015/11/16 (M) Tiling the Cockpit, #3

Linda planned to go to the bakery today but decided yesterday to stay home and help me instead. Based on the 10-day forecast this looks like our last decent weather day to work on the bus and we wanted/needed to make the most of it.

We had breakfast at 8 AM (granola with blueberries and a banana) and had a cup of Stash China Black tea. I had a text message from Kristine Gullen regarding getting together with her and Jim on Saturday and replied in the affirmative. We finished our tea by 8:30 and got to work.

I really wanted to finish tiling the cockpit of the bus, or at least as much of it as we could. That meant cutting and fitting tiles for the stair treads and risers and the two side walls of the entry steps, gluing them in place, and then grouting all of them. We needed to mount the table if possible and I also needed to build a new step for the platform. That was a lot to get done in one day and even before we started I doubted that we would get it all done.

When we opened the bus we were surprised to find that the tiles on the walls of the platform had slipped all the way down to the floor tiles. Obviously I should not have removed the spacers right after installing the tiles and should have to left them in place for any horizontal grout spaces on vertical surfaces. Oh well, not much to do about it now.

Keith called to see if he should come and mulch the leaves one last time. The weather the last few days had been very nice, unseasonably warm and dry. Today was also a beautiful day but the forecast going forward was for much cooler and wetter conditions, so this was an ideal day for our last lawn mowing of the 2015 season.

We measured and cut the tiles for the face of the platform and out to the door. At that point I evaluated what I needed to do to complete the job. Basically, I needed to cut all of the tiles for the entry steps and walls and then install them from the bottom up. Every piece of tile was going to be smaller than a full 16″x 16″ tile and custom cut so even though the square footage was not that much there would be more pieces than usual and it was obviously going to take quite a bit of time to get all of the pieces ready to install. I thought we could be ready for adhesive in two hours but Linda figured it would be at least three. It also meant working with the door open which would make it difficult to keep the interior as warm as we needed.

Phil showed up with his excavator and a dozen bales of straw. I knew the excavator was for a different job as he did not have anything left to do at our place that required it. He was here to finish covering the topsoil and grass seed with the straw. We took a break to go talk to him and confirmed that he was done with the driveway and French drain projects except for the straw. He staged the bales where he needed them but said he had to leave to dig a perk test hole at 1:30 PM and would be back mid-afternoon to finish spreading the straw around.

Linda suggested that we go ahead a grout all of the tile we had already installed. I was more emotionally invested in completing the tile work than Linda but had to agree that this was the prudent thing to do. Until the tile was grouted we could not reinstall the accelerator, the steering column shroud, the seat bases, and the seats, so grouting the tile was clearly a critical path item and that is what we did. It was after noon by the time we finished so we took a break for lunch. Phil had taken off by this time to go dig the test pit.

Lunch was grilled vegan Italian sausage on a bun with mustard and relish and black grapes on the side. Keith finished up mowing the yard while we were enjoying a cup of Rooibos tea. We paid him and chatted about next year. I gave him our approximate timeframe for returning home from Florida and asked him to go ahead and start mowing next spring whether or not we were here. We have had Keith take care of our lawn since we bought our house in the country and he has been very good about doing that when we are away and allowing us to catch up with him when we get back.

By the time we got back to work on the bus it was after 1 PM and I had to concede that we were done working on the tile until next spring except for cleaning them, which had to wait until tomorrow as the grout has to cure for 24 hours before final cleaning. With that decision made we considered what else needed to be done and in what order.

The first order of business was painting the two front seat bases black. We spread out painter’s plastic on the driveway and taped it down. We set the bases there and then masked off the top portion with the swivel bearings and mounting bolt. We wire brushed the bases to remove rust and then went over them with a sanding sponge. I used a cleaner/degreaser and water to clean them and then gave them a coat of black rubberized undercoating paint.

The next order of business was getting all of the tools and materials that we no longer needed out of the bus to give us room to work on other things. On Saturday I re-installed the bump out on the walnut cover for the passenger side HVAC duct. The duct needed to have two 4″ holes drilled in it to match the holes in the metal duct, so that was the next task. I measured very carefully and transferred the measurements to the face of the cover with equal care. Even so, I was off slightly and had to use the sheet metal nibbler to enlarge the bottom of each hole. At least I had a relatively straightforward way to fix this problem; I am not always so lucky.

With the holes enlarged we put the cover in place. The 4″ round plastic registers fit through the wood into the duct but not all the way due to two tabs. I trimmed the tabs off using the Porter-Cable oscillating saw and trimmed a little bit off of one of the outer mounting flanges to make it fit flush. I drilled holes through the two mounting holes on each register using the #5-6 self-centering drill bit and secured them with #6-5/8″ SR screws. We then removed the two temporary black plastic registers from the front of the built in sofa. I trimmed the tabs off of two new brown ones and installed them using the same procedure as the first two.

In the grand scheme of things getting the cover in place and the four registers installed was a small task but it needed to be done and stood in the way of other things. The cover has been stored on top of the two front seats, which have been lying on their backs on the kitchen floor of the bus for weeks. We plan to re-install the seats late tomorrow afternoon.

Two more small, but critical, tasks were securing the pull-out pantry and the refrigerator. I have assumed for quite a while that we would secure the pantry for travel with some form of sliding latch but had not thought about it in any detail. We also needed to secure the refrigerator but I had not thought about this in any detail either. As we pondered the pantry latch it slowly became obvious that we did not have enough wood for a strike plate to receive a pin and we did not have two unobstructed surfaces that were in the same plane, which would be required for the kind of latch I had been thinking about.

As for the refrigerator, one of our bus nut friends secured their unit by running mounting bolts (machine screws) through the floor of the cabinet above the fridge and threading them into the unused tapped holes provided for the upper door hinge (if it was reversed) . After looking at it for a while we realized that we could attach a section of small angle to the inside of the right alcove wall with the other side just against the face of the fridge case but not over so far as to interfere with the door gasket. My measurements indicated that a 1/2″x3/4″ angle would be just right. It looked to me like two 12″ pieces, one by the freezer door and one by the bottom of the fresh food compartment door, would be more than adequate to keep the refrigerator from rolling out as it cannot shift sideways or twist due to the aluminum angle on the left/hinge side at the floor.

About this time Phil returned in a red pickup truck. He finished distributing the straw and loaded three unused bales into the back of his truck. He pulled up in the main drive and we invited him into the bus to see what we had been working on all summer. It is always a pleasure working with Phil. If/when we build a barn we will have him do all of the site prep and finish grading. He will figure out the final cost for the driveway extension and French drain and send us an invoice.

Linda prepared an easy but tasty dinner consisting of a nice green salad, mixed frozen vegetables (corn, peas, and carrots) suitably reheated, and mac-n-cheese that was both dairy-free and gluten-free. After dinner we went to Lowe’s and The Home Depot. At Lowe’s we bought a 1/16″ thick 1/2″x 3/4″ aluminum angle and three 8 foot lengths of brass colored nose edging but did not find a latch that we liked. At The Home Depot we bought some screws for securing the handle on the front of the pull-out pantry and a solid brass door stop to keep the pantry in place. The door stop folds up when not in use and should work to keep the pantry closed while traveling.

Although the new Panera on the southwest corner of Grand River Avenue and Latson Road was finally open for business we stopped at Teeko’s Coffee and Tea on the northeast corner of that intersection. Jeff was there and took our order for eight pounds of coffee beans. We got two pounds each of Ethiopian Yirgacheffe, regular and decaffeinated, the Seattle Blend (regular), and the Sweet Dreams blend (decaffeinated). They will roast the beans and then let them outgas for a few days before vacuum sealing them in half-pound portions. This allows us to take them with us in the bus and keep them very fresh until we are ready to use them and to change what we are drinking more often.

We got home just after 8 PM and took our iPads downstairs to use while we watched our Monday evening CBS TV programs. We caught the weather forecast and then headed to bed. It looks like we will have two more days with unseasonably high temperatures near 60 degrees F but with intermittent rain and then a serious cooling trend with highs this weekend barely above freezing. Our time for working on the bus and being in Michigan is definitely running out.

2015/10/20 (T) Pop-X Pickle

Leave a reply

It’s a good thing there are still five weeks until we depart for Florida; there are a lot of unfinished items that need to be taken care of on the bus and around the house/property before we go.

When Phil is here my attention tends to be on what he is doing. He really knows his stuff, and is an excellent contractor to work with, but since he is not working from drawn plans there are inevitably questions and discussions about just exactly what it is I want and whether that is the best idea or even doable.

Phil had ordered a load of sandy soil for delivery first thing this morning and the “train” (double trailer) showed up not long after he did. The sandy soil he wanted was not available so he got clean sand instead. The train driver of the backed it over our third culvert and into the part of our yard were Phil wanted the material dumped. That took a lot of skill and was impressive to watch. I took a few photographs but video was really required to capture what was happening. The Sony SLT-a99v does video in several different modes but I am just beginning to learn how to use it as a still camera and did not want to mess around with shooting video. Besides, I am not a videographer; it’s a completely different way of thinking than being a still photographer.

Phil digs the trench for the electrical conduit from the SW corner of the garage to the far side of the driveway extension where he also dug a hole for the post that will support the RV outlet box.

With the material on site Phil was at the point where he needed to dig the trench for the RV electrical feed. That meant I had to quickly make some final decisions. I had an 8 foot 4″x4″ treated post and the PVC conduit pieces I needed to go from the post under the driveway to the other side but not enough to go all the way to the garage. If I only put conduit under the driveway I could cap it, let Phil bury it, and then dig it up later and finish trenching from there to the garage. I would not do that by hand, however, so it would mean having Phil come back next year just to dig this little trench. Although I could have him dig the foundation hole for the ham radio tower at the same time that still did not make any sense to me. Among other considerations I would have to fill the trench in by hand after I ran the cable.

Another option was to still use conduit just under the driveway but go ahead and run direct burial cable like we did two years ago for the pull-through driveway in front of the house. I would need three (120VAC) or four (240/120VAC) large wires (or equivalent service entrance cable, each at least 80 feet long to get from the outlet box location in the post to the riser pipe on the garage and through the wall into a circuit breaker box. Not only would I have to get the wire, which would be expensive, I did not have the outdoor outlet box or other parts I needed, so it would take me quite a while to go buy everything. I also did not know exactly where/how I would feed the circuit. (I had some ideas about that but they depended on just what the electricians do tomorrow.)

The most expeditious, and least expensive, option was to get more conduit and additional fittings and run the conduit all the way from the post to the southwest corner of the garage. I left at 9:30 AM for Lowe’s as Phil started digging the trench and the hole for the post.

At Lowe’s I picked up five more 10′ pieces of 2″ PVC conduit, a 45 degree elbow, another 90 degree elbow, a right angle entry box, and a bag of 2″ conduit clamps. By the time I got back to the house Phil had the post set in place and most of the trench dug. I got all of the conduit pieces laid out on the ground and got the PVC cement, a hack saw, and the rope and weight.

Since Phil could not do anything else on the driveway until the conduit was installed he helped me install it (or vice-versa). We joined 10′ sections to both ends of one of the 90 degree elbows and then dropped the weighted rope through it. We then set the elbow and one of the straight sections in the trench with the elbow at the base of the post and the other straight section going straight up the post where I secured it with two clamps. We proceeded to drop the weighted rope through additional straight sections of conduit, applied PVC cement to the ends, and put them together. The conduit had to be inserted about 3″ into the mating piece and twisted as it went in. I was glad Phil was there to help with this as I did not have the grip strength to do it by myself. (I don’t have a lot of physical limitations but the arthritis in the base of my thumbs makes itself known in specific situations.)

When we got near the southwest corner of the garage we measured and cut a section of straight pipe to get us to a turn in the trench. Because of a decorative grass plant the trench could not go directly to the desired location on the west side of the garage and had to go between the grass plant and a nearby small evergreen bush and then turned towards the garage. We installed a 45 degree elbow to get around the corner and it ended up in the center of the trench. When I said Phil knew what he was doing I meant it. We again measured carefully and cut a short section of straight pipe to get us to a 90 degree elbow that would turn up and bring the conduit out of the trench and up the side of the garage. I measured and cut the vertical riser section and we cemented it into the elbow. We now had a complete run with conduit coming out of the trench vertically on both ends.

Phil back fills the trench for the electrical conduit from the corner of the garage to the RV electrical post.

While Phil used his excavator to scoop and push dirt back into the trench and tamp it down I closed off both ends of the conduit. At the garage end I removed the gasketed cover from the entry box, cut a short piece of 2″ conduit, and put it in the fitting hole on the back side. Next I brought the weighted rope up through the bottom fitting hole of the box and used Gorilla tape to secure it inside the short back pipe. I put a cap on the other end of the short back pipe and then put the entry box on top of the riser sideway. I coiled up the extra rope, taped it inside the box, and put the gasketed cover back on. I did not cement any of these connections. When permanently installed the gasketed cover will point away from the wall and the hole in the back will have a longer piece of paper 2″ conduit cemented in and going through a hole into the wall of the garage.

At the post I used a Rigid brand pipe cutter, designed specifically for cutting large plastic pipe and conduit, to cut off the vertical riser at a convenient height above the top of the post. I threaded the rope through a 3/8″ hole in the center of a 4″ disc of 3/4″ plywood and tied a big knot in it. I modified the 2″ cap by drilling three adjacent holes lengthwise from the bottom up and cutting out material with a hacksaw to make a slot. With the rope hanging over the edge of the conduit I lined up the slot in the cap with the rope and put the cap over the end of the conduit.

Since I decided to not have Phil build the area leading up to the planned barn location I wanted to pull all of the unneeded yellow plastic stakes out of the yard and put them away. Re-staking the layout, however, is a time-consuming task so I put 10″ metal (iron) spikes at the locations of the front corners of the barn and the center point for the curved transition into the driveway. I drove them flush with the soil so Keith would not hit them with his mower but we can find them later with a metal detector.

With the conduit installed and the trench filled and tamped, Phil filled started building the “curbs” for the driveway. He had excavated parts of the driveway path and filled in other areas to create a base for the construction fabric and road gravel that was eight inches below the finish grade. The construction fabric is 12’6″ wide and Phil likes to wrap it up on the sides about 8″ so when he staked out the driveway to be 11′ 2″ wide. Phil used the sand to build up the areas along both sides of the driveway so that it looked like he had cut the driveway out, but that is not, in fact, what he had done.

My main bus project today was cleaning up the kitchen and living room, which mostly involved moving tools back to the garage. It is a confined workspace and tends to get cluttered over time as we fetch tools for this and that. I also wanted to be able to see the desk and its Corian countertop.

Two of the three sets of cushions in place on the new built-in custom walnut sofa/storage base.

I called Butch in Quartzsite, AZ regarding the distributor tester. He suggested that I send him an e-mail requesting Bill’s e-mail address and he would send it in his reply. We then discussed the refrigerator and he suggested that I set the freezer to a colder setting, leave the fresh compartment setting as is, and monitor it for a while to see if it changes. I did that and reset the min/max memory for both compartments.

Phil is not done with the French drain yet and spent part of the afternoon working on that instead of the driveway. He made lots of trips back and forth with the front loader to take the topsoil he had removed to create the driveway, spread it out along on top of the pea gravel that fills the drain trench, and grade it off to blend with the undisturbed yard along either side of the drain. Before he is all done with these two separate, but inter-related projects, he will have to bring in several truckloads of topsoil. It will be used to fill low spots, especially at the west end of the property, and to cover everything that has been disturbed. All of the topsoil will be finish graded to blend into the existing contours of the property and then seeded with grass seed.

The view from the living room looking towards the hallway. The new built-in custom walnut desk has its Corian countertop in place and the new refrigerator is in place next to the built-in custom pull-out pantry.

I did not want to get involved in any complex or time-consuming projects so I hung out on the west half of our yard where Phil was working and took lots of pictures with the new camera. Actually, I had been doing that all day trying to document the work as it progressed. When I wasn’t taking photos I gathered up broken branches and larger deadfall and carried or dragged it to the brush pile on the west side of the line of large fir trees that separate the east and west halves of our five acres.

Linda called around 3:30 and asked me to see if her wallet was on her desk. She thought she had it with her but could not find it. She finally located it in her car where it had been since falling out of her case this morning. She was on her way home by 3:50 PM.

I had a final chat with Phil, who won’t be back until Saturday, and then closed up the bus and the garage. We were headed to Ann Arbor this evening and I needed to get cleaned up and put on nicer, more appropriate clothes for our evening out. I used to wear Oxford shirts and nicer pants every day for work, and sometimes a sport coat and tie or even a suit. These days it’s mostly polo shirts and blue jeans or sometimes REI ripstop nylon convertible cargo pants. And this summer it has mostly been my work jeans and work shirts.

We left around 5:15 PM and were parked in Ann Arbor before 6 PM. We agreed to meet Kate at the Lab Cafe which was just around the corner from the Thompson Street parking garage. (This garage is behind the former Border’s book store #1 which also housed the company’s corporate headquarters. Our daughter started with Border’s as a cashier at this store and within four years was a regional manager for their PaperChase product line before the company imploded and went bankrupt.)

Kate was sending Linda text message updates on her travel status and ETA so we ordered a couple of decaf coffees to go. At $3.75 each they were pricier than we are used to paying for coffee but they were “hand-crafted” and the coffee was very good. It took the barista at least 10 minutes to make our cups, grinding the beans just before brewing and then slowly pouring hot water through individual filter holders after pre-wetting the filters. In the time it took to make our coffee I would have been on my second cup at Panera.

Linda (front) and Kate (behind) take in the interior of one of the Pop-X art exhibit sheds.

The music was too loud and really awful, a bad combination in our opinion, so we sat outside in spite of the occasional attempt to rain. When Kate showed up we walked the short distance to Liberty Park to see the Pop-X Art Exhibit. Organized by the Ann Arbor Art Center, all of the art was displayed in “sheds” designed by an architect, one artist per shed. The sheds were approximately 10 feet square with steep pitched roofs. The roofs, and the two sides they pitched down to, were covered in clear wavy plastic panels to let in a lot of natural light. The back end was solid and the front had a pair of sliding “barn style” doors hung from tracks. There was a solid floor that was elevated relative to ground level and provision for electrical power. They were designed to be sold as potting sheds after the exhibit was removed at the end of the week. Although the light was fading I was still able to get some decent shots with the new Sony a99v DSLT camera. It has much greater light sensitivity than the Sony alpha 100 it is replacing as my primary camera and this was my first opportunity to take advantage of that since getting it.

Our main reason for coming to Ann Arbor was to have dinner with Kate but Pop-X was a nice bonus. Ann Arbor has a LOT of dining options; hundreds I would guess just in the very walkable downtown area. We decided to try the Grizzly Peak Brewing Company after Linda confirmed that they had some things on the menu we could eat. It was a bit of a walk but the rain held off and it was an otherwise pleasant evening.

Linda had a dark Porter with definite chocolate tones and I had a hard cider with distinct cinnamon/vanilla tones. It was also supposed to have roasted pecan notes but I did not detect that. Kate had a red beer that was not hoppy and thought I might have liked it. I had a sip of Linda’s Porter and it was very agreeable. We both had small couscous and greens dinner salads, which were very nice, and both had wild mushroom burgers, which were excellent. Linda said her chips were also very good and my French fries were tasty and generously portioned. Kate had a burger and all of our meals came with pickles. Kate does not care for pickles, which I knew, and does not care for vinegar in general, which I did not know, so Linda and I split her pickle rather than have it go to waste. The waiter was very attentive and a good sport when I asked for a gallon of ketchup for my fries. He brought two very full bottles for the table and a bottle of Frank’s hot sauce. We tipped him accordingly.

At 9:30 PM we started a slow stroll back to the parking garage and chatted a while longer by our cars, which coincidentally were parked very close together. It was 10:40 PM by the time we got home. I fed the cats and we went straight to bed. I was up later than I wanted to be trying to outline this post but I had not had much opportunity to work on it throughout the day.

2015/09/24 (R) Blood Work

Leave a reply

Linda got confirmation yesterday that our lab orders had been put in by our doctor. The blood work requires a 12 hour fast (minimum) so we finished dinner last night before 8 PM and did not have breakfast this morning. We headed out around 8:30 AM for the Henry Ford Health System Columbus Center in Novi, the nearest HFHS lab to our house. We would not normally get on I-96 at that time of day due to rush hour traffic but we wanted to get this taken care of early and then get something to eat and drink. We got to the lab at 9:15 and it only took a few minutes to get our blood drawn. We then headed to the Panera on Novi Road at Grand River Avenue for bagels and coffee and some down time to sit, relax, read, research, and write.

Linda spent some time last evening researching wallpaper installation but found conflicting information. I got online and looked at some of the same websites. Wallpaper is a little out of style at the moment and some of the website information was over 10 years old but still seemed relevant. The interior walls of our motorcoach are finish grade plywood that is firmly attached to the structure of the bus with spray foam insulation underneath. The issue is how to prep the plywood before we hang the wallpaper. Some sources indicate that we need to size it, some say to prime it, and others say to use a liner material and then prime, all before hanging the paper. Other sites, however, say to just hang the paper directly on the plywood and be done with it.

We left Panera and were headed west on Grand River Avenue. We noticed that Chuck’s truck was at his shop so Linda made a U-turn and we stopped to see if he was there. He was, so we visited for a while and got to see their new refrigerator and discuss the installation, which Chuck somehow managed to do all by himself. Even with the use of his forklift, that was quite an accomplishment.

We got back to the house at 12:45 PM, changed into our work clothes, took care of a few chores, and had a light lunch of fresh apples, pears, and hummus with onion on rye bread. I then called Josh Leach at Coach Supply Direct and left a message asking him to follow up with Ferman Miller at Countertops Plus. If Ferman does not have any more of the Sandstone Corian I want to make sure Josh gets the 30″x48″ piece from the other supplier before it disappears.

The entrance landing with the floor removed revealing the pneumatic linear actuator that operates the slide out stepwell cover.

When we finally got to work on the bus around 2 PM Linda focused on stripping the old wallpaper and I started preparing the entrance for tiling. She taped off all of the wood trim where she is working, spread painter’s plastic to protect the floor, and wrapped the two living room captain’s chairs. I removed the existing vinyl tile from the entry platform, removed the plywood cover, and uninstalled the step well cover. I then removed the tile and treads from the stairs. I also moved the passenger seat forward and determined that I can probably get to the swivel shaft retaining nut from the back. Removing the seat by removing this one nut will make it much easier to tile that part of the cockpit. Ditto for the driver’s seat.

Although we got a late start on the bus today, and worked on it for less than four hours, we were satisfied with what we accomplished. The old tile came up more easily than I thought it would which bodes well for getting the entry/cockpit tiled with the new Armstrong Alterna Luxury Vinyl tile.

I called Phil Jarrell to verify that he had called Miss Dig and told them to mark the gas main and not just the utilities running to the house. He said he did and expected that they will be here on Friday. I will keep an eye open for them and intercede if possible. Phil expects to start our job on Tuesday. If he does he will probably be finished by the end of the week or over the weekend.

The entry stairs into the bus with the bottom riser cover plate removed to reveal one of the two air-conditioner compressors installed in the spare tire compartment. This is how the ports are accessed for service and recharging. The other compressor is accessed through the bay under the driver’s seat.

Linda let me know that our lab results were available so we each logged in to our HFHS MyChart accounts to look at them. Linda’s lipid profile showed a higher total cholesterol than she expected and she was not happy about it. Dr. Vangel had seen the results and commented that they were OK, but Linda was perturbed about it none-the-less. My total cholesterol was also higher than I would like but not as high as Linda’s. Her LDL and HDL numbers and ratio looked good and her HDL, in particular, was much better than mine. This was no doubt a consequence of her almost daily exercise walking. We apparently do not fully understand the lipid profile numbers or what we still need to change about how we eat to bring them in line with the guidelines put forward by people like Drs. Neal Barnhard and Caldwell Esselstyne.

Linda made a nice salad to start our dinner, served with a small glass of Moscato. The entrée was a mock chicken scaloppini that she picked up at Whole Foods. For a side dish she steamed kale with mushrooms, onions, and garlic. After dinner we sat on the back deck and enjoyed a second small glass of Moscato.

I went to my office and edited the blog posts for July 23 through 31 and hope to upload those posts tomorrow. I had an e-mail from Molly Pinner with Linda’s invitation to work as an office staff volunteer at the 2016 Escapade in Essex Junction, Vermont. I replied to that and cc:d Linda. I then e-mailed Lou and Val Petkus to let them know. I was wrapping up for the evening when I got an e-mail from Ed Roelle with the September CCO Newsletter. He develops the newsletter in MS Word and I convert it into PDF for him. I took care of that and sent it to him and then went upstairs to watch a PBS program on scenic train rides of North America.

The program was interesting but PBS was fundraising again, and the fundraising segments were longer than the programming segments. It seems like this has been going on all summer and we are, quite frankly, tired of it. After clicking around the other channels I turned the TV off and went to sleep.

2015/09/13 (N) Club Business

Leave a reply

Linda is still fighting her cold and I was up way too late last night so we slept until 9 AM this morning. Because we were getting a late start, and neither of us was hungry, I made coffee but we skipped breakfast.

It was 51 degrees F in the bus so I turned on all three electric toe kick heaters and put on my zip front sweatshirt that I use to work in cool situations. We took all of the freezer packs out of the house refrigerator freezer compartment and moved them to the freezer compartment in the bus fridge. Linda also filled four large containers with water and snapped the lids on. We put those in the refrigerator compartment on the bus, turned on the power, and put the wireless remote thermometer in the freezer compartment.

I was going to raise the front of the refrigerator until the top hinge for the freezer door just touched the ceiling of the alcove but our relatively inexpensive model apparently lacks that adjustment. Linda was also concerned about how we will latch the doors for travel. She remembered seeing a very clever latch for a fridge with doors like ours at the GLAMARAMA rally in early June and found a picture of it on her phone. It is actually fairly simple and if custom made could be installed using the holes for the center hinge (between the doors) on the handle side (right side) of the fridge.

(I still like Scott Bruner’s solution best. He devised an electromagnet system that is activated by turning the ignition on but has an override switch. He and Tami have a cafe door, bottom freezer drawer unit. One electromagnet holds plates on top of the cafe doors where they meet at the center of the fridge. A second electromagnet is mounted on the right side of the lower case and holds a plate on the side edge of the freezer drawer front. Very clever, and very fail safe.)

Bruce installs the fixed side of the piano hinge to the top of the wiring chase above the OTR HVAC duct.

Our first construction task for today was to finish installing the built-in sofa. This was a semi-permanent installation with everything in its final place and screwed in. We will have to disassemble it once to finish cutting it and screening off the openings in the OTR HVAC duct and to drill the 4″ diameter holes in the vertical front panel for the circular registers. We also need to find a pair of suitable length lifts to support the seat in the open position. Finally, we need to find and mount some 12V DC LED lights and replace the momentary contact switches in the aft end cabinet with on-off versions.

It took us until 12:25 PM to finish the sofa (for now). We took a brief break and had an apple for a snack. Our next task was to put the plywood bed platform back in the coach. That sounds simple enough but we knew from taking it out that it would be difficult to put back in. The platform is the size of a queen size mattress, in two sections joined by a piano hinge. It’s big, bulky, and very heavy, with no good handholds but we managed to get it into the bedroom and setting flat on the storage box base.

The physically hard part was behind us but now we had to get the fixed part of the platform screwed back down to the base, requiring us to put 18 screws back in the holes they came out of. I rewired the aisle lights before we did that as I was easier to get to the wires. We used two screws to index the location, checked the reveal along the length of each side, and screwed it down. I then reconnected the two gas springs while Linda held the platform up. I also connected the wiring for the two cargo lights but they did not come on. I will have to change the bulbs and see if that’s the problem but for now we had more pressing tasks.

A view from near the co-pilot/navigator seat of the built-in sofa with the hinged seat base lifted up to reveal internal pieces and storage space.

We went inside, each had an apple, and then returned to the bus. I had planned to temporarily mount two 12V DC switches but did not have time to fabricate a temporary mounting plate. We needed the switches hooked up so I just reconnected the female spade connectors on the cable to the spade lugs on the switches and draped the wires over the arm of the passenger chair.

Our next task was to temporarily install the desk. The installation was only temporary in the sense that we would need to disassemble it to get the Aqua-Hot fan-coil heat exchangers installed in the bases. My preference was to get the heating system configured as part of the desk installation but we ran out of time before our appointment at Coach Supply Direct.

Our first sub-task was to cut the 1/4″ Baltic birch plywood spacer to fit on the right side of the right pedestal/base. I cut it to be shorter than the desk and not as deep as the base, which is recessed at the front to create a toe kick space. I cut the lower back corner out so the space would fit around the HVAC duct / wiring chase. We peeled off some clear tape from the mirrors in the right rear corner down below the level of the top of the desk and set the spacer in place.

Our next task was to redo some AC wiring to get power to the space between the pedestals and reconnect the passenger side front duplex outlet. To get power to the interpedestal space I decided to run 2C+G (Romex) cable from the wiring chase through a hole in the bottom of the pedestal, up the inside rear left, and out through a hole in the upper rear left side. This hole and cable will not be visible unless someone crawls under the center of the desk.

In order to get the cover/shelf in the foot well aligned with the left and right pedestal/base components I decided to use mending plates attached to the back side of the bases and pedestals. We started with the right hand components. I attached a plate to the back side of the left rear base projection and one to the underside of the left end of the upper bottom section of the pedestal. We set the base in place, put the pedestal on top of it, and set the cover/shelf in place.

We carefully shifted the components until we had them aligned the way we wanted. I then secured the pedestal to the wall (which is 5/8” or 3/4″ plywood not sure which) with a single screw through the back panel centered from side-to-side and a couple of inches down from the top edge. We double-checked the alignment of the pieces and then secured the pedestal to the base with three screws. The base is not screwed to the floor or anything else except the pedestal.

We set the left base and pedestal in place and fussed with the alignment for but it was already 4:15 PM. We had planned to quit working at 4 PM to get cleaned up for our SLAARC meeting and have dinner. We still have a lot to do tomorrow for me to be ready to leave on Tuesday morning, but it should be manageable.

We went to Panera in Brighton for dinner and both had the Edamame Soba Noodle Bowl. It was a generous serving that was tasty and filling even though it was only 390 calories. It was very high in sodium, a common but unfortunate problem with most of Panera’s food, so not something we would eat often.

We arrived at the South Lyon Witches Hat Depot Freight House at 6:30 PM for the monthly meeting of the South Lyon Area Amateur Radio Club (SLAARC). We had a larger group than usual, at least 30 people. The business meeting was brief and followed by a program by Steve (N8AR) on the Yaesu Fusion technology. Steve and several other club members brought different radios to demonstrate and let the attendees try.

We left in time to get home by 9 PM and watch an episode of Sherlock on Detroit PBS, followed by Rick Steve’s Europe and then Music Voyager. We’ve been working long, hard hours and it was nice to take an evening to relax and do something other than work on the bus.

2015/08/21 (F) Have Fridge Will Travel

Leave a reply

I was up at 7:40 AM and made a pot of Costa Rican half-caff coffee. Linda was up just before 8 AM and washed off some fresh blueberries to put on our breakfast granola. The Costa Rican is definitely not our favorite coffee and I brewed it with a little too much water which did not improve matters. But we bought a pound of beans and are not going to throw them out so the sooner we use them up the sooner we can get something that we like.

Harvey Carter (AC8NO), the current President of our South Lyon Area Amateur Radio Club, agreed to help us move the old bus refrigerator from Chuck’s shop in Novi to our house this morning using his cargo van. He pulled into the parking lot of the shop right behind us at 10 AM. Chuck and Barb had already left for Oscoda in their bus with their race car trailer in tow.

After opening the shop we had Harvey back his van up to the overhead door. We brought several lengths of 2x4s planning to use them under the back of the refrigerator but Harvey had two ramps made from 2x12s with a cross piece that spanned the rear bumper. That looked like a much better alternative to us. He also had a good hand truck and a ratchet strap.

We decided to truck the unit from the left side because the refrigerant and water lines protrude beyond the back of the case. We removed all of the trays from the doors and cabinet but left the shelves in place. We slid the hand truck under the left side of the cabinet and secured it with the ratchet strap. With Harvey on the hand truck we tilted it back and rolled it out to the ramps. We adjusted the ramps so the hand truck wheels would be centered on them. Harvey then pulled the hand truck up the ramp backwards as Linda and I pushed from the bottom, eventually lowering it all the way down as we slid it fully into the van. I then closed up the shop.

I rode with Harvey in the van and Linda followed us in the car for the trip back to our house where I had Harvey back his van up to the small garage door. Reversing our procedure from earlier we unloaded the fridge by rolling the hand truck down the pair of ramps and put it just inside the small garage bay near the door. We plugged it in and it started running so at least we did not break it.

We wanted to put the drawers and door bins back in but could not get the fresh food compartment door open more than a few inches. I was able to open it just enough to see inside and determine that at least two shelves had come loose and wedged into positions that prevented the door from opening. The solution was to remove the door. I undid the three screws that attach the top hinge to the cabinet and removed it, allowing Harvey to lift the door off of the bottom hinge. I reattached the two shelves to the mounting rails at the rear of the cabinet. Harvey then set the bottom door hinge pin back in the lower bracket and held the door while I reinstalled the top hinge. We will plug it in later next week and let it cool off as it has to be running and cold when DTE Energy comes on Friday to pick it up.

While Linda unloaded the drawers and bins from the car and put them back in the refrigerator I gave Harvey the ham radio tour. We looked at the antennas on the tower, the cable entry box, and the ham shack with the multiple monitor wall mounted track system we installed. I then gave him a tour of the bus interior. Linda was getting ready to go for a walk but I suggested we take Harvey to lunch and agreed to go. He lives in Green Oak Township southeast of Brighton so we went to the Panera on Grand River Avenue at I-96 as it was in the direction of his house and we all like their food.

After lunch we drove to the frame shop in Howell and picked up the last of four paintings we had framed. We were pleased with our choice of framing material and the owner, Rick, did a nice job assembling it. We headed back to Lowe’s and looked at thin paneling materials. Linda got a shield for the bird feeder that is supposed to keep the squirrels from getting to the seed block and I got a recessed outlet that I am considering using for the refrigerator in the bus. We stopped at the Walmart adjacent to the Lowe’s but did not find the peanut butter filled pretzels we were looking far. I needed a battery disconnect for the lawn tractor battery but we did not feel like doing anymore shopping today and returned home.

It was late enough in the afternoon that I did not feel like getting the air compressor out and working on the floor of the bus so I went to my office while Linda went for a walk. I was going to upload a few blog posts but decided to work on an article for Bus Conversion Magazine instead.

I took photographs of two buses at a pair of converted bus gatherings in Quartzite back in January of this year. Larry and Carol Hall had a very nice GM4106 at the FMCA Western G.M. Coach rally while Byron and Betty Pigg had a gorgeous Model 15 Eagle at the Eagle International converted bus rally. Larry and Byron are the presidents of their respective groups and the rallies took place at the same time in adjacent sections of the Quartzsite Marketplace dry camp area. This campground is near the epicenter of RV vendor activities and only a mile from where we were camped. Gary Hatt, the owner/publisher of BCM, brought his newly acquired Eagle conversion and had his mobile mechanic drive his MC-9 Moose Creek Motor Cabin, which was for sale. He invited me over so we could finally meet in person, I could meet a few folks, and photograph the buses. He knew, in particular, that Larry and Byron were interested in having their buses featured in the magazine and figured I could help make that happen.

I had started articles on both buses right after I photographed them and worked on them a bit back in February but I did not get them finished before we had to leave Quartzsite in early March. Once we pulled up stakes we were on the move and very busy and I did not get back to them before we got home. Of course, we got even busier once we got home so new articles for BCM were on the back burner with the gas turned off. But magazines have lead times with deadlines for each issue, and Gary very much wanted to feature both of these buses before 2016 arrived, so I dusted them off and decided to work on the article about the Hall’s GM4106.

Larry had sent me a brief narrative some months ago and I had started filling in the detailed specifications about the bus and conversion. I had already selected possible photos for the cover and centerfold as well as the article and post processed some, but not all, of them. I massaged Larry’s narrative, added an introduction of my own, extracted some additional specifications, and then focused my efforts on completing the post-processing of the photos.

I took a break for dinner and afterwards completed the photo processing. I then started inserting the thumbnail versions of the images into the Word document and writing captions. There isn’t really any magic to writing an article; it’s just a specific kind of work. You string words together into sentences, organized by paragraphs, that tell a short story about something interesting and you illustrate it with captioned photos that are hopefully relevant and technically adequate. It takes time and energy to do this well, however, and I ran out of both around 10 PM.

2015/08/15 (S) Steve and Karen

Leave a reply

As we were backing out of the driveway to go to our weekly ham radio breakfast we noticed a large mailbox sitting on the ground next to ours. It was still attached to the upper half of its wood support structure. The number was 593, which is not an address that occurs on our street. We left it there and went to breakfast.

We had a mid-sized group of 15 people at our SLAARC breakfast this morning. On the drive into breakfast we lost power to our GPS every time I transmitted on the 2m ham band. The GPS and cellular booster worked fine all day yesterday with the new 12VDC extension splitter, but I did not use the mobile ham radio.

After breakfast we went directly to Chuck’s shop in Novi to see if we could retrieve the old refrigerator using our car. A measuring tape quickly revealed that the fridge would not fit without removing the seats. Even then it would be too long to close the rear gate and hatch on the Element. At breakfast Harvey (AC8NO) offered the use of his van and labor to help move the fridge and I will probably take him up on it.

On the drive home I chatted with John (NU8M) on the South Lyon 2m repeater and we were joined by Mike (W8XH). After John signed and dropped off Linda tried different combinations of power connections while I talked with Mike. Based on that test the splitter appears to be the problem but we could not determine if it was a voltage drop issue or some form of RFI.

I stopped on the way home to fill the gas tank in my car. When we got home I put the mailbox in the back of my car and we drove to the end of the street but it clearly did not come from one of our neighbor’s yards. When we got back to the house we also noticed that there was a footprint on the side of our mailbox. Closer inspection revealed that the post was slightly loose in the ground and the box was leaning (bent) slightly to one side. Clearly someone had tried to kick it over (and failed) and there was a very high probability that it was the same person(s) who probably broke the other mailbox and left it on the ground next to ours. We discussed whether we should report it to the Livingston County Sheriff Department but did not take the time right then to do so.

Linda needed to make a grocery store run and then prep the food for dinner and pick up the house. With company coming later I did not want to get all sweaty working in the bus and garage so I worked in my office editing and uploading blog posts. I quit around 3:30 and was writing blog posts when Steve and Karen Limkemann arrived at 4 PM.

We always have a nice visit with Steve and Karen and they are good sports about eating the vegan food that Linda prepares. Linda made a sweet and sour collard greens cole slaw and vegan potato salad ahead of time. She cooked corn-on-the-cob on the stovetop and heated vegan beer brats on the grill along with onions and green peppers. Steve and Karen brought a Malbec wine which we enjoyed before, during and after the meal. Dessert was fresh strawberries with cashew milk snickerdoodle ice cream. Really, what’s not to like?

Steve and Karen have rented a house trailer in a trailer park near Venice, Florida for the last few winters. I think they rented it for January, February, and March and split the time with another couple, but I may not have my facts completely straight. The owners of the trailer are from England and decided after this last winter that they want to start using it during the winter so Steve and Karen lost the use of it. They really liked the park and its location so they bought a trailer that was for sale and already set up. We visited them two winters ago, but we were several hours north of them. This coming winter we will be much closer to them while we are in Arcadia during January and February and plan to see them more often. Venice is a very upscale place and there is an excellent vegan restaurant within easy walking distance (a mile) from their trailer park.

We talked about trying to catch the tail end of the Perseids Meteor Shower but the peak was earlier in the week, they would not be visible at our location until midnight, and then only low in the northeast sky, which is not an ideal viewing direction from our yard. Steve and Karen had a 45 minute drive to get home and left around 10:30 PM. By that point it had been a long but very satisfying day for us and we were straight away to bed once they were safely on their way.

2015/08/08 (S) A New Bus Fridge (Finally)

Leave a reply

We overslept and did not get up until 7:15 AM. The weather has been very pleasant all this past week but we awoke to light rain. We left for our SLAARC breakfast at 7:25 AM and took a different route than usual to see how it would be for the bus. I headed north on Hacker to M-59, east to US-23, and south to I-96 east. The ramp from US-23 south to I-96 east is a left exit, left entrance, with a very short merge lane in the middle of a major construction project. I decided that was not our best option for the bus.

We arrived at breakfast at 8 AM to find a dozen people already there but at least 10 more showed up after us. We enjoyed the conversation, as we usually do, but did not linger and were on our way back home by 9:15 AM. As soon as we arrived we changed into our work clothes and got busy with the final preparations to move the bus to Chuck’s bus garage in Novi.

I pulled the bus out at 10:30 AM and Linda followed in the Element, which had all of the pieces we had removed from the old refrigerator along with tools, blankets, and some 2x4s. The bus roof was brushed by a few small, low branches getting from our house to N. Hacker Road, reminding me that I need to covertly trim trees and bushes along our street. I say covertly because they are not on our property. The last time I took the bus out we went south on Hacker to Grand River Avenue. This would have been our preferred route today except that the trees are not trimmed up in a few places and one of them, just before Bendix Drive, clunked the stuff on our roof pretty hard last time. I did not care to repeat that so I went north as we had this morning in the car.

At M-59 I headed west to Latson Road, a trip of some four to five miles in the wrong direction. The reason is that Latson Road going south has a relatively new, and easy to navigate, intersection with I-96. From there we had an easy run to the Beck Road exit, a short jog south to Grand River Avenue, an easy left turn, and the final mile to Chuck’s shop where we arrived at 11 AM.

Chuck had already pulled his bus out of the building and parked it out of the way but there were several trucks and a dumpster trailer blocking access to his door. They belonged to a motley crew that the owner of the building in front of Chuck’s shop had hired to clean up some of the mess left behind by the sunroom company that just moved out of the building. He had me pull up to the right and position myself to back up and then negotiated with the workers to move their vehicles. I pulled up the tag axles and waited. The workers were not happy about it but they did it.

To get our bus into Chuck’s shop nose first he had me back parallel to the building and then bring it around to the passenger side into a space adjacent to the front building until I was perpendicular to his door. I was then able to pull straight in but I did not pull in all the way. Chuck had me stop with the fixed window frame opposite his forklift which he had already positioned for use. The on again, off again light rain was not a factor as the window frame we needed to open was well inside his shop.

Linda and I unloaded all of the stuff from the car and brought it inside the shop. We realized that we forgot to bring the camera so Linda tried to capture the progress of the work with her cell phone camera. I have put those images in a separate gallery post for this date.

Randy, the owner of the Printology business in the suite adjacent to Chuck’s, came over to see what we were up to and stuck around to help. With me working from an 8 foot step ladder outside the bus, while Chuck and Linda worked inside, we opened the window frame about 24 inches and propped it with a piece of 2×4. I then carefully lifted the window higher while Linda sighted along the bottom of the upper cabinet. When I had the frame high enough to be clear of the cabinet Chuck measured the length of 2×4 we would need to prop it open.

It looked like 52 inches would do the trick. I had a 56″ piece of 2×4 so I cut it down to 52″ with my 7-1/4″ Rockwell circular saw. I used the first piece to mark a second piece on an 8 foot 2×4 and cut that. Linda took both pieces inside the bus where she handled one and Chuck handled the other. As I lifted the bottom edge of the window from outside the bus the window hinge (at the top) made some unpleasant (and a bit unnerving) sounds but I got it high enough that they could put the two braces in place and the frame did not come unhinged. We had just finished this task when John Rauch and his son, John, arrived at noon to help move the refrigerators.

The old refrigerator was lying face down in the bus. The two Johns lifted it as a test and determined that they would not have any difficulty moving it. Linda fetched one of the blankets and dropped it over the sill of the open window to protect it and the side of the coach. Chuck had placed the long forks on his forklift about two feet apart and slid a narrow pallet over them. He raised the forks and brought the forklift forward towards the bus. We got him to position the top of the pallet even with the top of the sill and about 3″ away from the side of the coach.

John and John are very strong and were able to lift the old refrigerator case and pass it through the window onto the pallet. With a person on ladders on either side of the pallet we slid the refrigerator all the way out. Chuck then tilted the forks slightly, slowly backed away, and lowered it down. John and John got the old refrigerator off the pallet, carried it out of the way, and stood it upright on its base. They then lifted the new refrigerator onto its back, picked it up, and placed it on the pallet. They went back inside the bus while Chuck brought the forklift up to the coach and raised the forks until the pallet was at window sill level. John and John slid it into the bus, stood it up, and rolled it into the alcove. I then secured it in place with a piece of 1×3 wood screwed to the floor across the front to keep it from rolling out while driving. There is approximately three inches of space above the fridge but it cannot tilt out very far before the upper back edge catches the ceiling of the alcove.

John, John, and Chuck raised the window frame slightly to remove the 2x4s and close the frame when the top hinge started coming apart. Linda yelled for me and I scrambled over to get another pair of hands on the frame. With me and Chuck holding the outside (free) edge and the two Johns holding the hinge edge I was able to see where the hinge was out and direct folks as to what to do. It took several tries and a few minutes (that seemed like hours) but we got the hinge re-engaged and then closed the window frame. We took a few minutes to rest and chat and Chuck showed John (the father) his race car. The heavy lifting was all done so John, John, and Randy took off, but before they did Linda gave John (the son) a gift for their new baby girl, Lucy Violet.

Linda and I put all the shelves and bins in the new refrigerator and then reattached the two doors. That was a bit of extra work as it came with the hinges on the right side but we needed the door to open on the right side. With the doors on we took a moment to consider our choice of size and color (black) and felt we had made the right decision. We started to reassemble the old refrigerator but we were all hungry and decided to go to lunch first. I started the bus and pulled it all the way into the shop so we could close up. Chuck then drove us down the street to Panera for lunch. We took our time and had a nice meal and a nice chat.

Back at the shop we decided to switch the buses around so Chuck would be free to leave. He wanted a picture of the two buses together so I backed ours out of his shop, swung around to the passenger side, got parallel to his bus, and then backed up so the nose of our bus was about 10 feet behind the nose of his. He and Linda then both took photos with their cell phones. When the photo shoot was done I pulled forward to the left and then backed in parallel to the building about four feet from the curb. That gave Chuck plenty of room to pull up next to me on my passenger side and then back around next to the front building and get lined up to pull straight into his bay just as I had done earlier.

Back in the shop Linda wiped out the inside of the old refrigerator and then we reattached the two doors. As she cleaned each rack, shelf, and bin I placed it back into the refrigerator. When it was fully reassembled we plugged it in. It came on, ran for about 60 seconds and then shut off. It obviously was not cold yet, and might have been cause for alarm if I had not dealt with this “problem” before.

I knew from prior experience that the defrost timer had probably disconnected the compressor and connected the evaporator defroster. Chuck pulled out three of his lawn chairs and we sat around waiting for the refrigerator to restart. The only thing missing was three cold beers. We knew the unit still had power as the lights were working. There was an outside chance that the overload protector (fuse?) might have blown, but I did not consider that to be likely. Our patience was rewarded about 25 minutes later when the compressor came back on. While we were waiting we gathered up our tools and various materials and loaded everything back into the Honda Element.

Chuck had a message from his wife, Barbara, with her ETA so we decided to settle back into the lawn chairs and kibbutz until Barb arrived. She showed up a little while later and Chuck got out a fourth chair and we sat in the shop listening to the sound of the functioning refrigerator and debriefing the events of the day. As a result of the window frame hinge coming loose I am now of the opinion that I did not need to remove the two stop blocks. I suspect they are there to “stop” the hinge from coming apart and I should not have removed them. Chuck is also thinking about replacing the refrigerator in their bus and is going to check with Prevost regarding these blocks. As much as anything I was annoyed with myself for the amount of time I wasted removing these blocks but what is done is done and I now need to reinstall the one block that came off undamaged and get a replacement for the other one, even though I can only attach it with one machine screw. Butch thinks he can make one for me, otherwise I will have to get one from Prevost.

Our local electrical utility, DTE Energy, will pick up used appliances. In the case of a refrigerator it has to be plugged in and running, which I presume means it is functioning and cooling the interior. If so, they will take it away and send us a check for $50. From our end that’s a good deal as we don’t have to pay someone to haul it away. Because of the R-12 Freon there are very few places that will deal with it. My guess is that DTE has a sub-contractor who will recover, clean, and recycle the R-12, which is no longer being made and has become very expensive. They may also recycle the copper tubing and electrical wire, and possibly the metal case and other materials. Even with the labor to do this work the unit must be worth more than $50 to them.

We all needed to get some dinner so we wrapped up our visit and started up our bus. I pulled out onto westbound Grand River Avenue followed by Linda in the car. At Beck Road we turned north and then got on I-96 westbound. The bus was at 3/8ths of a tank of fuel so I decided to stay on I-96 and go to the Mobil truck stop at M-52, a run of about 30 miles that would allow the engine and transmission to come up to normal operating temperature. Linda exited at Latson Road and stopped at Meijer’s to do some grocery shopping.

The Mobil truck stop is run down with a very poor, pot-holed apron and parking area, but there are usually several tractor-trailers fueling here when we pull in as it is one of only two places that a semi can refuel between Detroit and Lansing. There weren’t any trucks getting fuel when I pulled in but it was 7:30 PM on a Saturday evening and there were a half dozen tractor-trailers settled in the parking area for the night. I poured two bottles of Stanadyne diesel fuel additive into the fuel tank followed by two ounces of Racor Biocide. I then added 125 gallons of diesel fuel to the tank, which took about 11 minutes. By the time I paid for the fuel and was ready to pull out it was 8 PM.

I called Linda to let her know I was on my way and then reset the trip odometer. I drove east on I-96 for 10 miles to the M-59 / Burkhardt Road exit and got on M-59, which only goes east from there. Eleven miles later I made the turn south onto N. Hacker Road and completed the drive to our house. Linda heard me idling in the street, where I stopped to lift the tag axles before making the tight right turn into our pull-through driveway, and came out to help get me parked. Once I was positioned correctly I put the tag axle back down, let the engine low idle for a minute to let the turbo spin down and let the heads cool off and the temperature to equalize, switched the Level Low system out of drive mode, and shut off the engine. I shut off the air supply to the engine accessories, shut off the chassis batteries, connected the shore power cord, locked everything up, and went in for the evening.

It had been a long day and we were glad to have it behind us. I had been anticipating the refrigerator exchange, with some dread, for well over a month. The concern was that we would not be able to move the units out/in through the window frame, requiring us to remove and replace the lower passenger-side windshield, or that something would go wrong, like the hinge, and turn out to be an expensive and difficult problem to fix. With each passing day it was also becoming a bottleneck in our remodeling project, at least psychologically if not physically. But it was finally done and ended well. We will plug in the new refrigerator tomorrow to make sure it works. We tested it in Chuck’s shop when it was delivered so we expect it to work now. There is a lot of work to do but now we can get on with it and I expect it to go well.

In spite of being tired we stayed up and watched the PBS broadcast of the Simon and Garfunkel reunion concert they did live in New York City’s Central Park 10 years after they split up as a duo. Their music remains among my most favorite from my youth and it has lost nothing with the passing of many years.

2015/07/23 (R) Wrapping Up Mara

Leave a reply

Mara’s plan was to make this the last full day of her visit. Our day started without her as we had cinnamon raisin toast, juice, and coffee for breakfast. I got a call from Jarel with clarifying questions and ideas about the desk and the pull-out pantry. After a thorough discussion we had better ways to approach a few things. He also had a better feeling for the estimated cost of the project and I agreed to send him 50% as a deposit.

I typed up a short letter and printed off the graph that Steve made of the return loss for the M-302N V/U lightning arrestor. I packed the unit for shipping to Morgan Manufacturing and included the letter and graph. Linda wrote out the check for Jarel and got it in an envelope to mail. She then went to the library, Post Office, and Humane Society where she donated cat and dog paraphernalia that we had accumulated over the years.

While Linda was gone I worked in the bus for a while and Mara worked on travel preparations. I started by removing the old 3/4″ plywood floor from the refrigerator alcove. The original plywood bus floor appeared to mostly be in good condition but I will put a new secondary floor in the alcove to keep the refrigerator legs above the level of the new tile floor. There are a LOT of wires running along the floor of the alcove at the back wall and I may fashion a cover for them and seal up the holes at either end.

I removed the AC dimmer for the living room lights and the DPDT momentary contact DC switch from the floor-mounted walnut box where they were installed. The DC switch controlled the passenger side sofa footrest. I had to remove the wires from both switches to get them out. The AC dimmer was easy but the DC switch had four different color wires with spade connectors. I made careful note of which terminal each color went to and then pulled the spade connectors off. With the switches out I was able to remove the box and its mounting cleats from the floor and wall. This area will be tiled and the box will not be reused.

Out of curiosity I tested the switch with an Ohm meter to see how the terminals were connected internally. I also checked the wires with a DC volt meter to see how they were being used. Two of the wires were +12VDC and DC ground and the other two went to a connector that was originally plugged into the footrest. The switch applied 12VDC to the two load wires in one position and reversed the polarity in the other position, making the footrest go out or in respectively.

Last year I had removed two blank outlet covers on the walnut panel next to the co-pilot seat so I knew that these two switches were originally installed there and subsequently moved to the floor-mounted box. I unscrewed the 1/4″ walnut veneered plywood panel from the wall to see what was behind it. What I found was a LOT of wires and it was not a pretty sight. I re-installed the two switches in their original locations and re-routed some other wires so they went up over the HVAC chase.

There was still a large bundle of wires running along the floor at the base of the HVAC chase that I needed to re-route but I decided not to mess with those today. They are connected to four different switches and a doorbell and disconnecting everything was going to require careful attention to detail. I pondered the refrigerator some more and decided there wasn’t anything else I could do with it for now and that I was done working in the bus for today.

There is too much to do at the moment to just sit around so I decided to install the new garage door opener for the small garage door. New is relative; it has been sitting in the garage in its original packaging since we moved into the house, supplied by the previous owners. The old one has not worked correctly since we moved in and the previous owners bought the new one but ran out of time to install it. It turned out to be rather more complicated than I expected, with very comprehensive assembly and installation instructions. It also turned out to be a two-person project so Linda worked on it with me.

We were working and Mara had started prepping dinner when a UPS truck showed up with four boxes. The delivery included: Mara’s refrigerator vent cover; the Cutco knives and scissors, and; the ZioTek track system for wall-mounting the monitors in the ham shack (2 boxes). The vent cover was due for delivery today but the knives were not due until tomorrow, so we were really glad to see them as two of them were for Mara. The monitor mounting system was also due for delivery today but I had temporarily forgotten about it.

The north wall of the ham shack/office. This is where the ZioTek wall-mounted monitor mounting system will go.

Mara was understandably anxious to see if the vent cover fit her base properly. It was a VentMate and appeared to be identical to the old one. She climbed up the ladder on the back of her motorhome and I handed parts and tools up to her. I then climbed up was well. She removed the old cover and we set the new one in place. It was a perfect fit! We put a small amount of putty under each screw head and then ran them down snug and congratulated ourselves on another job completed and well done.

With Linda’s help we put Mara’s kayak back in its custom carrier which fits in the receiver on the back of her motorhome (she does not tow a car). The carrier was built by a welding shop in Mesa, Arizona to Mara’s specifications and is made from 2″ square tubular steel and powder-coated black. The carrier holds the kayak diagonally across the back of the motorhome from lower left (driver’s side) to upper right. The nose of the kayak sits in a pocket near the driver side rear corner of the motorhome and the midpoint is nestled in a much larger cradle. A strap runs from the nose pocket up to the midpoint on one side and across the kayak to the other side where it is attached to a ratchet and has a hook on the end. With the hook engaged in a ring the strap is ratcheted tight and the kayak is secure for travel. Mara runs an anti-theft cable through an eyelet near the nose and attaches a lock for safe keeping. The tail sticks up higher than the top of the roof-mounted air-conditioner covers but does not extend beyond the passenger side wall. The tip of the kayak is 13′ 2″ from the ground.

We made good progress on the garage door opener but had to stop at the point where we needed to attach the motor housing to the ceiling as I needed to get some parts (angle iron and lag screws) that did not come with the unit. The front of the track was attached to the header above the door opening and we left the motor assembly resting on top of a 6 foot stepladder.

The pieces of the ZioTek monitor mounting system laid out on the floor of the ham shack/office.

While Mara and Linda prepared dinner I unboxed all of the monitor mounting components. I was curious to see the parts and wanted to make sure everything was there and undamaged, which was the case.

Dinner was Thai vegan spring rolls in rice flour wrappers. The prep work was in the cutting of lots of veggies (carrots, zucchini, onions, red and yellow peppers, Chinese cabbage, and mushrooms). Mara made two dipping sauces, one with ginger, hot peppers, and other things and one based on fish sauce (so we passed on that). Linda selected our bottle of Malvasia Bianco wine from the Heart of the Desert winery in Alamogordo, NM. It was white, which we thought would go well with the delicate spring rolls, but very sweet with a slightly thick mouthfeel, like a late harvest Riesling or a Sauternes. Perhaps not the best choice, but we finished the whole bottle anyway.

We chatted for a while after dinner but like most of our evening meals dinner was a drawn out affair with lots of conversation. Everyone was tired and the women turned in for the night. I went to my office and answered e-mails from Gary at BCM that I had seen earlier in the day. I then went to bed and tried to catch up on blog posts for the last few days but could not stay awake long enough to finish them.

2015/07/22 (W) Chucking Junk

Leave a reply

After our usual breakfast and coffee we sat for a while in the living room. This is part of our morning routine and I often use the time to finish up my blog post from the previous day but the last couple of weeks we have been busy and I have not always had time. We enjoyed the time until about 9 AM and then got serious about loading our “junk” into the Chuck It Junk Removal dump trailer.

Our bus refrigerator with the doors off in preparation for removing it from the coach.

Mara checked with Cummins Bridgeway and they told her to bring her motorhome in at 11 AM so she broke camp at 10 AM and backed out of the driveway at 10:15 AM. Cummins Bridgeway put several technicians and mechanics to work on her rig to re-install the genset, install new shock absorbers, and service the transmission (filter and fluid). She was out in a few hours and stopped at General RV to return the Camco refrigerator vent cover which did not fit her base on the roof.

The Chuck It Junk Removal dumpster trailer with some of our stuff in it.

We took a break from chucking junk and extracted the old refrigerator from its alcove in the bus, which was a 2-person job. I got some scraps of 1/2″ plywood to set in front of the elevated alcove base as I did not want to walk or slide the unit across the bus sub-floor, especially with the residual thinset mortar. First we had to walk it out a few inches which was hard because it only had 3/8″ clearance on each side. Once it was out far enough we were able to open the doors enough to remove all of the shelves and bins, which Linda took into the house and garage. I then disconnected the water and electric that ran up into the left (freezer) door at the bottom hinge corner for the ice/water dispenser and light. With those disconnected and pulled out of the bottom of the case we unscrewed the bottom and top hinges and removed the two doors. Linda collected all of the small loose parts as we went and put them in a plastic container as we knew we would have to reassemble the unit at some point.

The doors had 1/4″ walnut veneer plywood face panels and we wanted to salvage those to use with the new pull-out pantry. Normally you just remove the handle trim from the edge of the door and slide the panel out. The fridge door panel would not budge so we removed the trim from all four edges of the door. The panel had been stuck in place with strips of double-sided tape so we carefully peeled it loose. The freezer door had two smaller panels, above and below the ice/water dispenser, and they slide out easily after removing the handle trim. We carried the doors, trim, and panels to the garage and then walked the case completely out of the alcove.

The shelf I built for one of the storage bays on Mara’s Fleetwood Bounder.

I spent some time pondering what would be required to disassemble the refrigerator enough to get it out through the door of the bus but decided not to do anything until I had talked to Butch. Just before dinner I had a long chat with Chuck about the refrigerator swap and he reminded me that DTE Energy (the electric power utility for this region) will pick up old refrigerators and freezers and pay you $50 for them. Linda checked this out online and learned that they have to be plugged in and operating or they won’t take them, so we have a double incentive for getting it out in one, operating piece.

Our revised plan is still to get the case out in one functioning piece through the side window frame but it won’t be this weekend. The guy with the sunroom business in the building in front of Chuck’s shop is still in the process of moving to his new place and has trucks, cars, people, and junk all over the place making ingress/egress to Chuck’s shop difficult to impossible. The business is supposed to be gone by the end of the month so we will wait another week and plan for Saturday August 1st assuming I can get the window frame open. In the meantime I need to get back to work on the bus floor, so I will have to spend part of next week sanding and start installing the 1/4″ underlayment for the new vinyl tile.

Mara in our home kitchen with her wonderful pizza. This thing was truly good eats.

Mara and Linda made another pizza for dinner and it was every bit as good as the first one. Mara has been a wonderful house guest. We have left the house open to her and she has made herself comfortable in the kitchen and using the hall bathroom and laundry. It helps that Linda is not possessive about the kitchen. Whenever we have visitors who want to help in the kitchen Linda welcomes their participation. It’s been fun for both of them and they have each learned a few knew things and deepened their friendship.

2015/07/10 (F) Eye of the Beholder

Leave a reply

I was up at 7 AM and made coffee. This usually wakes Linda up, but not this morning. After waiting a reasonable amount of time I went ahead and started drinking. If someone tells you that 7:30 is too early in the morning to be drinking don’t believe it, and if someone tells you that you should never drink alone don’t believe that either.

Linda eventually got up but looked really tired. Unbeknownst to me she had awoken in the middle of the night and not been able to get back to sleep. Neither of us were hungry after the large meals we had last night for dinner so we just had a little juice to wash down our little pills (vitamins and an allergy pill for me).

I’ve been looking for a system to wall-mount multiple flat-panel LCD monitors above/behind the desks in the ham radio shack portion of the downstairs office. Linda was helping search for products and found AFC Industries in New York. Their website had a large variety of very serious looking products. The ones that caught my eye were a 72″ wall mount track with four articulated monitor mounts and a 48″ track with three mounts. They had an 800 number and the website said to call for pricing. That’s usually a bad sign but they appeared to have exactly what I needed so I decided to call them later.

I had planned to work on the custom desk design all day but Linda had other ideas. She had become frustrated with the clutter in the library and the inability to really clean that room and decided that today was the day to do something about it. Point acknowledged. Some of the clutter (but not all) is artwork and she thought the place for us to start was to get some of it hung on the walls. Again, point well taken and agreed. Doing this correctly is a slow process, however, so I knew my plans for the whole day had just changed. Sometimes you have go along to get along.

We have artwork that is not currently displayed which ranges in size from 8″ x 10″ to 2′ x 5′. Some of it is framed and ready for hanging and some of it is not. It is mostly paintings but there is some photography, a few poster prints, and some textile pieces. We went through every piece looking primarily for oil paintings that we liked and that would fit the spaces we had available to hang them. Before we were finished with this project for the day we had hung eight paintings. We also found four paintings that we liked but lacked frames, or ways to hang them, and set them aside for now. Most of the paintings were done by Ann Metzger, my late great Aunt, but one was done by my late mother. We had also moved a few items out of the library into the driveway to be donated to the Salvation Army. I tend to use drywall screws with large fender washers as hangers as they are strong and very secure. We ran out of stainless steel fender washers so that created a natural stopping point for our task.

For a change of pace I decided to climb the tower to measure the center sleeve inside diameter so I could determine what outside diameter mast to get. I got out Mike’s climbing harness, set up the step ladder, put on the harness, climbed up onto the roof, connected the waist strap around the tower, and started climbing. I alternately attached and detached the two safety cables and made good progress until I got to the DB8e OTA TV antenna. To go higher I would have to move from the west face to the northeast face and then undo the waist strap and reconnect it above the mounting point for the OTA TV antenna. I did not feel like doing that today. I was, however, able to reach the bottom of the sleeve by extending my tape measure. The tip of the tape fit inside the bottom of the sleeve with what appeared to be about a quarter inch to spare. I then climbed down and got off the roof, got out of the climbing harness, and put it away.

Back in the house the tip of the tape measured approximately 1-1/8″ across thus it appears that the sleeve is sized for a 1-3/8″ outside diameter mast. I checked Universal Towers website, since they are located in S. E. Michigan, but their selection of aluminum masts did not include this O.D. OnlineMetals.com has 1-3/8″ O.D. 6061-T6 aluminum tube in five different wall thicknesses and a large variety of lengths so that may be the easiest way to get one. But first I will check the usual ham radio places.

Next I called AFC Industries and was routed to Ewa who was very curious what I was going to use the multiple monitors for since I was not a company. I tried to explain why I would need at least three monitors in an amateur (ham) radio shack but she had never heard of ham radio and I don’t think I did a very good job of explaining it. She was paying attention to what I was describing, however, about where I wanted to position the monitors. She could not give me pricing on the phone so I gave her my e-mail address to send a quote. Ewa was prompt in the sending the quote but I did not see it until later as we had the leftover seitan stroganoff for lunch and then left to run errands.

Linda had loaded our donation items in the back of my car while I was on the phone. I brought seven paintings to the car and we left. Our first stop was the Salvation Army donation center between Brighton and Howell. We then went to the Howell Art and Framing Center, a frame shop on the east end of downtown Howell. The proprietor, Rick, worked with us quite a while as we selected frames for four of the seven pieces and played with his Jack Russell terrier, Rudy. These four pieces will go in the library when they are done in about three weeks. Our final stop was Meijer’s where we picked up fender washers, salad greens, and coffee filters.

Back at the house I went to my office to check e-mail and work on the desk design. The quote was there from Ewa and she had already made a follow up phone call so I opened the e-mail and looked at the quote. It was almost double what I expected which was already double what I wanted to spend. I e-mailed her back and asked for a simpler configuration but politely explained that her numbers were way out of my price range. The interesting thing about such experiences is that the Ziotek products I’ve been looking at on the CyberGuys website suddenly do not seem so expensive. It’s funny how that works.

While I was working I got a TXT message from Chuck following up on the refrigerator installation. I texted back that I had not yet checked whether we can open the fixed glass window frame but would do so immediately and call him back. I moved the 7′ step ladder next to the bus and climbed up to inspect the stop blocks as Linda pushed the window open. The two stop blocks on that frame were definitely contacting the drip rail immediately above them preventing the frame from opening more than about 8 to 10 inches at the bottom. The good news was that the Zip Dee patio awning would not interfere with the opening of the window. The bad news is that I was not able to remove the two Philips head screws that secured each block to the frame.

I called Butch to find out what the tool was that I used at his shop to work on my brakes. He said it was a manual impact tool. This nifty little device is a screwdriver that turns through a small angle when you strike the end of it with a hammer. This has the unique benefit of driving the screwdriver bit into the screw head while turning. Butch thought that any auto store would have these so I called the local O’Reilly’s but they did not have any in stock in the store.

While I was talking to Butch Linda was researching other places to buy such a tool. It turned out that Sears would be a good choice but the closest one was at Twelve Oaks Mall over 20 miles away. I was getting ready to drive there but called Chuck first. It turned out that he has two of them so I will borrow one tomorrow after our ham radio club breakfast. I spent the last couple hours of the evening working on the desk design. I then went to bed and worked on this post.

2015/06/18 (R) Chiseled Bikinis

Leave a reply

The light rain that started late yesterday afternoon continued off-and-on through the overnight hours. We awoke to heavily overcast skies but a forecast that called for dry conditions until the early afternoon. We were up at 7:15 AM and had our usual granola breakfast. I took some more Ibuprofen in advance of working in the bus. We were just getting ready to have our morning coffee when I noticed several cars in the driveway. It was 7:45 AM and the roofers were arriving. Pat Davidson was among them so I went outside to chat briefly with him.

We had our morning coffee and then got to work, Linda at her desk and me in the bus. I spent another two hours using the Makita 11 pound power chisel. By 11 AM I had removed as much material from the floor as I felt was worth the effort. Linda brought the camera out and took a few photographs of me at work after which I packed up the equipment, closed up the bus, and went to Home Depot in Howell to return it to their rental department.

I stopped at Lowe’s on the way home and ordered the new Frigidaire refrigerator for the bus, an FFHT1621QB (16.3 cu. ft., top freezer, black, no ice maker or water). I scheduled delivery for Friday July 3rd to Chuck’s shop in Novi. I will arrange with Chuck to take the bus their sometime after that when he is available to operate his fork lift and I can get Brendan or some friends to give us a hand.

Me using the Makita 11 lb power chisel to remove thinset and mastic from the floor of our H3-40. (Photo by Linda)

Work continued on the roof through the morning and then the crew tarped off the roof and left in a few of their vehicles for a long lunch. As forecast it started to sprinkle around 2 PM as they returned from their lunch break. It never rained hard and they kept on working but always with the tarps at the ready in case they were suddenly needed. One of the guys finished installing our two Velux Sun Tunnel skylights which required a tall step ladder in our living room. They looked very nice when he was done.

I had a chat with Jarel Beatty in Logansport, Indiana about the custom desk he is going to build for the bus. I sent him a follow-up e-mail describing the pullout pantry we also need him to build. I then spent an hour working on drawings before I had to quit and change clothes.

Kate had secured tickets through her cousin, Michaela, for this evening’s performance of The Bikinis at the Meadow Brooke Theatre at Oakland University in Rochester Hills. Kate suggested O’Conner’s Public House (Irish Pub) in Rochester for dinner. The roofers had been working in the living room installing the Velux Sun Tunnel skylights but were done by 3:45 PM. That allowed us to get cleaned up, dressed for the theatre, and out the door at 4:30 PM even though the roofers were still working up on the roof.

We got to the pub at 6 PM. Kate got there shortly before us and had ordered a soft pretzel appetizer before the happy hour prices expired at 6 PM. Conveniently there were three large sticks so we each got one. Kate got the cheesy dipping sauce and we split the spicy horseradish mustard, which really had a kick to it. Linda and Kate each had a Smithwicks ale and I had a pineapple ale. To paraphrase “the world’s most interesting man”: I don’t always drink beer, but when I do, I prefer a fruit beer. Not as mysterious as Dos Equis, or as authentic as Guinness, but it’s what I like. Kate had a regular (beef) burger and we both had black bean burgers on soft pretzel buns with fresh hand-cut French fries. The burgers and fries were both really good and the pretzel buns, which had been toasted on a grill, did not get soggy.

The musical was a lot of fun with a wonderful performance by the cast of four women. All four of them were on stage singing and dancing with a lot of energy for most of the performance. Their singing was excellent, each voice having its own unique quality but blending well, and they carried 4-part harmonies in tune with one another and the small 4-pieces band. Two of them, Bambi Jones and Jeanne Tinker, were also in the Meshuggah Nuns musical we saw a month or so ago at the Meadow Brooke Theatre.

The Bikinis is the last production that Kate’s cousin Michaela will work on at the MBT. The production run ends on Sunday and one week later she leaves for a summer stock gig in New England. Meadow Brooke Theatre is a wonderful venue but not convenient to where we live, even less convenient to where Kate works, and very inconvenient to where she lives. All of which is to say, I doubt that the three of us will be going there very often now that Michaela is moving on. That is too bad in a way as we have all enjoyed the shows we have seen. The fact that Michaela, as a cast/crew member, was able to get us tickets did not hurt.

Michaela met us in the lobby where Kate gave her a nice assortment of flowers. She then gave us a behind the scenes tour of the wardrobe area where she has spent the past year working on costuming. We walked out to our cars and by the time we all drove off it was 11 PM. Even with light traffic it took us almost an hour to get home but we arrived while it was still Thursday, albeit just barely.

2015/06/17 (W) Bakery Scraper

Leave a reply

Linda was up at 5:45 AM and out the door by 6:15 AM to beat the morning rush hour traffic headed into the northwest corner of the Detroit metroplex. I got up about an hour later, tended to my morning cat chores, made coffee, had some granola for breakfast, gathered up the trash, and took the big trash can to the street.

The Apex roofing crew started showing up just before 8 AM. After everything was squared away with Apex I went to The Home Depot in Howell to rent the small power floor scraper. The scraper took some of the thinset off but was not as effective as I had hoped it would be. The tool is designed for stripping linoleum floors, so I had no reason to complain that it did not do what I needed it to do. I returned it within four hours and paid the 4-hour rental fee rather than the day (24-hour) fee. The guy in the tool rental department suggested I try a different machine which they had not mentioned to me previously. It was a Makita 11 pound power chisel. I rented it with three chisels.

The roofers were at the point where they needed to install the two Velux Sun Tunnel skylights in the roof of the living room. I showed them where I wanted them installed, if possible, and they tarped off the furniture and floor in the living room. Apex is very good about protecting the yard from damage and capturing the mess that is associated with a roof project. That same care and attention carried over to the inside work, which I appreciated.

Our bus looking forward from the the hallway by the refrigerator and pantry.

After a break for lunch I spent most of the afternoon using the power chisel to strip the area of the floor in the bus where the ceramic tile was installed. I was not able to strip it down to the plywood subfloor, but I was able to knock down most of the ridges of thinset and adhesive that remained after I chiseled out the tiles.

I had a brief chat with Chuck around lunchtime regarding the refrigerator. Butch called mid-afternoon to fill me in on why he was not able to answer the phone last night. Linda called around 2:30 PM to let me know she was leaving the bakery. She pulled in the driveway an hour later and came in the bus to see what I was up to and let me know it was starting to rain. I had made good progress but was not done and decided I would keep the power chisel until tomorrow and pay the 1-day (24-hour) rate.

The roofers were aware of the rain, which was very light though increasing steadily, but were in the middle of replacing plywood and installing the skylights. Some of them finished that up as quickly as they could, cleaned up the roof, and spread out the tarps while the others picked up the debris from the yard and got it in the trash trailer. The trailer was full so they took it with them when the left at 4:40 PM.

We had a snack of pretzels, green grapes and a small glass of Moscato wine. My thumbs were both bothering me (arthritis) so I took some Ibuprofen and then went back to work in the bus. I had to close the roof vents because of the rain so it was warmer inside and a bit stuffy as the humidity had come way up. I worked as long as I could and quit for the day at 6 PM.

For dinner Linda made a simple green salad and then cooked some whole wheat capellini and tossed it with the homemade tomato-based Marinara sauce she made the other day. After dinner I worked in my office for a while. I thought I would upload some blog posts but I had an e-mail from Bus Conversion Magazine with the draft of the May 2015 issue. I proofread part 2 of my 4-part article on the Exterior Makeover of our bus by Phoenix Paint. I found one thing that needed to be corrected and e-mailed it to the editor.

Linda got a DVD of Wild from the Howell Library the other day but we were too tired to watch it and just went to bed. I turned my light out at 9:58 PM, the first time since I can’t remember when that I have done that before 10 o’clock in the evening.

2015/06/10 (W) Ron and Mary

Leave a reply

Same routine as yesterday; up at 7 AM, open up the house, feed the cats, clean the litter tray, start a load of laundry, make the coffee, and drink the coffee while using our iPads.

Our daughter’s 34th birthday is tomorrow but she is flying to Las Vegas today to meet up with her husband who is there on a company outing. We will celebrate her birthday when they get back, perhaps in conjunction with Father’s Day and Linda’s birthday, which is at the end of the month.

Linda left at 9 AM for Brighton Honda to have the 12 V battery in her car checked. The battery light came on the other day so we thought it might need to be replaced. Around 9:20 AM I heard thunder and a short time later we had a brief, heavy downpour. Linda called at the same time and said the battery tested OK. The problem could be the alternator, of course, but presumably the dealer service people know that and checked for that. If not, we will likely be back there sooner rather than later.

Linda headed on to Meijer’s to do the grocery shopping. Today was trash pickup day so I took the trash can to the street. After meeting with Brad from Chuck It Junk Removal the other day we decided we would rent their trailer for 5 days. For the same price as having them physically handle 1/3 of a truck of junk (5 cu. yd.) we can get rid of a full truck of junk (15 cu. yd.) by loading it ourselves. Deal.

I got a call from Phil Jarrell regarding my request for pricing to dig a foundation hole for a ham radio tower foundation. It was a useful conversation in that I had not previously realized that I will need a concrete contractor in addition to the concrete supplier. The only thing the concrete supplier will do is show up with a cement mixer truck and dump the concrete where they are instructed to. The concrete contractor will actually place rebar, build forms, provide carts or a pumper, and get the concrete from the truck to the hole. Phil recommended Mike Fearer of Bid-Rite Concrete as a good guy who would work with me to get this done.

I talked with Chuck about getting a key to his shop so we could have the new refrigerator delivered there and have the old one picked up without having to trouble him to be there. He agreed and suggested that we contact the guy down the street about removing the old windshield and installing the new one as part of the refrigerator swap.

Rather than dig into our bus interior remodeling project I have used the last couple of days to finalize decisions about various products and order them. One of the things I have wanted/needed for a while is a cable entrance box that will allow me to route transmission lines and control cables into the basement from outside. I talked to Chris Perri, KF7P, at the Dayton Hamvention last month and decided that I liked his custom fabricated cable entry boxes. I got his business card at the Hamvention and exchanged a couple of e-mails with him this week. I decided this morning how I want the box initially configured and e-mailed my specs to Chris. I would like to run the cabling for the cell phone booster through this box so I needed to get it on order. Speaking of which, the cell phone booster system arrived today via UPS so I am feeling more comfortable that all of the stuff I am ordering will actually get delivered to our house.

Wednesday’s and Fridays are when Recycle Livingston is open and the Wednesday hours are 11 AM to 5:30 PM. We had my car loaded up with recyclables and Linda drove over after lunch to drop them off. When she got back she made a batch of her yummy granola and I got a couple more loads of laundry done while continuing to work at my computer.

After doing my alternate tile layout for the bus floor yesterday I decided that I liked the way it looked better than the original ad that it would not involve any more cutting than the row/column layout. I also felt confident that I had an accurate enough tile count to go ahead and order the tiles. I drove to the Shell station to fill my tank and then drove to Lynch Carpet in Howell. I ordered 12 boxes of the 16″ x 16″ Armstrong Alterna Luxury Vinyl Tile in the La Plata Creme Fresh pattern, and a gallon each of the vinyl adhesive and Glacier vinyl grout. There are 14 tiles per box (24.89 sq. ft.) for a total of 168 tiles (just under 300 sq. ft.). The inside floor area of the bus is around 300 sq. ft. before subtracting out walls and cabinets but we will be using some of the tiles on vertical surfaces in the entry stairwell and cockpit and around the box that supports the bed platform. My estimate is that I will have 10 extra tiles. The guy at Lynch Carpet suggested that I use a scrap piece of tile as a spacer when installing the tiles but I may use the little plastic “X” pieces designed for this purpose.

From Lynch Carpet I drove to Lowe’s in Howell to see if they had a different portable air compressor that might be more appropriate than the 6 gallon Porter Cable we just bought. The Porter-Cable air compressor has a maximum regulated pressure of 150 PSI but that is also the maximum tank pressure. I will have to test it on one of the front bus tires to determine if it will get the job done and if not I will return it.

The guy at Lynch Carpet also suggested that I rent a handheld grinder from Abe’s or A-1 Rental, both in Howell. Abe’s did not have any grinders of any kind and A-1 was closed on Wednesdays. The gal at Abe’s suggested the tool rental service at the Howell Home Depot, so I stopped there. They also did not have a handheld grinder but they did have a floor model concrete grinder. It was so heavy that I doubt if we could have gotten it into the bus and it was too big to maneuver in the tight spaces where I need to work. They did have a lighter/smaller floor stripper and I may give that a try before I resort to grinding off the thinset with an angle grinder and diamond impregnated wheel and/or a belt sander with a very aggressive belt.

Pat Davidson called from Apex Roofing while I was out so I called him back. They will be able to start on our roof next week Monday or Tuesday and will deliver the shingles on Friday this week. I confirmed that we wanted two of the 14″ light tunnels for the living room. I also indicated that I had scrapped the idea of building a dormer or installing a roof hatch as I simply did not get this taken care of in time.

Linda had closed up the house and turned on the air-conditioning while I was out. It was pulling moisture out of the air but would not bring the air temperature lower than 78 degrees. Not good. This will be our third summer in this house and we have not used the air-conditioning very much. The first summer we were gone for most of June, all of July, and a few days in August. We had the unit serviced last year and thought it was working OK but perhaps did not really use it after that. We did install filters in the return air grills so perhaps they are restricting the airflow too much. It is also possible that it needs refrigerant. I will have to check our records from last year and then call TOMTEK to arrange to have it serviced again.

Linda’s brother, Ron, and his wife, Mary, arrived early this evening. They are on their way to northwest Illinois for a week-long organized bicycle ride. They have to be there on Saturday and will be spending the next three nights at our house. Visits from them are usually not more than once a year but we really enjoy their company when they are here.

For dinner Linda made a nice green salad and then made whole wheat angel hair pasta with onions, garlic, and mushrooms lightly sautéed in olive oil. Ron does not imbibe but Linda, Mary, and I had a glass (or two) of Moscato. We moved to the deck after dinner and had fresh strawberries for dessert. It cooled off as darkness set in and we eventually moved back inside. The other three were in the kitchen and I was sitting on the sofa when Juniper suddenly caught a mouse in the middle of the living room, or at least that is where I noticed that she had it. She took it downstairs and I got her to drop it in the bathroom sink but I was unable to get it into a container to take it outside and it escaped into my office. I closed the doors but I have no doubt it can go wherever it wants in the house from there. When I returned upstairs we chatted until 11 PM and then all turned in for the evening.

2015/06/07 (N) Too Soon, Too Late

Leave a reply

Unlike the Escapees Rallies, which always have a “hitch up” breakfast on the day of departure, the FMCA rallies always end with the entertainment the evening before departure day. On departure day there is an asynchronous but generally smooth exodus of motorhomes that can start as early as 6 AM. A small group of members from the Ontario Rovers chapter was parked across from our row of GLCC buses and they started firing up their engines at 7 AM and pulled out shortly thereafter. No one objects to, or is disturbed by, this as it is understood and accepted that folks need to get on the road as suits their personal plans and travel styles. We are usually required to vacate the rally venue by noon unless we are part of the debriefing meetings.

One of the things I find most interesting about rallies is the somewhat contradictory feelings many of us seem to have on departure day that the rally is ending too soon but we would have been glad to leave sooner. The sense that it is over too quickly has to do, for me at least, with the fact that we enjoy the camaraderie of our fellow converted bus owners who we only see very occasionally. The sense that it has gone on too long is just the fatigue of an intense multi-day event where every day is packed full of things to do.

John and Paulette pulled out around 9:30 AM followed by Don and Sandra and then Larry and Alma. The Canadian contingent of our chapter (two buses and a Class C motorhome) was headed to a campground in Middlebury, Indiana about 17 miles away. They had planned to leave just before noon on the presumption that they would not be able to check in any sooner than that. Karen called and found out their sites were vacant so they all prepped their coaches, hooked up their cars, and were gone by 10:30 AM. Once we saw they were getting ready to leave we did not have any reason to linger so we prepared our coach for departure and so did Scott and Tami. We both decided to hook up by our sites rather than at the dump stations. We pulled away just after 11 AM with them not far behind us.

We took the outer road along the southern boundary of the Fairgrounds over to the dump stations at the southeast corner. There are at least five parallel lanes that RVs can use to dump their holding tanks. We have never had to wait for one but when we got over there they were all in use and there were five motorhomes waiting to get in. We had to dump before we left, and so did Scott and Tami, so there was nothing to do but wait our turn. Soon enough we were able to pull up, hook up our sewer hose, dump our holding tanks, rinse out the hose, put it away, close up the bay’s, and head for the exit.

The easiest way in/out of the Elkhart County 4-H Fairgrounds is NOT through Goshen, Indiana which involves narrower streets, lots of traffic, and railroad grade crossings. From Gate 5 at the far northeast corner of the fairgrounds we turned right on CR-34 (Monroe St.) and headed east. About a mile later, give or take a bit, we turned left and headed north on CR-29. A couple of miles later CR-29 ended at IN-4 which we took east to IN-13. IN-13 starts (ends) at that point and only goes north from there.

We discussed whether to turn east onto US-20 or continue north on IN-13 but finally opted for the US-20 route. IN-13 becomes US-131 in Michigan and we could have taken it up to I-94, passing through Three Rivers, Michigan on the way. But US-20 is a good route that we have traveled many times and is the quickest way home from this part of Indiana, getting us over to I-69 very directly.

Once we got to I-69 the rest of our trip was on Interstate highways except for the last 13 miles. We stopped at the Michigan Welcome Center / Rest Area at mile marker 5 and then continued up to Lansing where we exited onto I-96 east. As we approached the exit for the Mobil Truck Stop at M-52 our fuel level was indicating just below a half tank and I decided not to stop and top it off. We talked about taking the Latson Road exit but M-59 is the most direct route home so I took that exit like we usually do. M-59 only goes east from there and rolls along interrupted by only two stop lights. Approximately 11 miles later I turned south on N. Hacker road and we completed the drive to our house.

We had very light and intermittent rain from the time we left the fairgrounds but it did not affect the drive. The only issue with the bus was that the Battery Balance Light and Vanner Equalizer Light both came on twice. Both times it happened I had just hit a very bumpy section of road so I am wondering if I have some loose cables. I have not checked the batteries in a while and terminal connections are probably due to be cleaned and tightened. The batteries are three or four years old at this point and are standard lead-acid maintenance-free batteries. I keep them on maintenance chargers when the coach is parked, but these batteries typically only last about 5 years so I need to check them and keep an eye on them.

We pulled into our driveway around 2:45 PM and Linda got out to direct me as I parked the rig. We were level without any adjustments so I shut down the main engine, switched off the batteries, closed all of the air valves, and plugged in the shorepower cord. It was not raining so we busied ourselves emptying the bus, including the refrigerator, of items we needed to get into the house sooner rather than later. We did not empty the freezer section as Linda needs to clean out and rearrange our home refrigerator freezer section first, and we left a lot of the clothes on board.

The wind was gusting stronger as the afternoon progressed. It continued to spritz off and on but the heavier rains finally came around 6 PM. They were initially isolated and intermittent but became stronger and more persistent as the evening hours advanced and by 9 PM we had lightning and thunder. Our son called around 9:30 PM just to check in with us, see how our week was, and bring us up to date regarding their activities. Last week was grand-daughter Madeline’s first full week of part-time day care. She will be staying home on Monday’s and Friday’s through the summer and hopefully be able to spend some time with Grandma Linda and Grandpa Bruce.

2015/05/07 (R) Meshuggah Nuns

Leave a reply

We spent part of last night researching a new refrigerator for the bus. Possibilities included models from 13.5 cubic feet to 17 cubic feet from various manufacturers. We found one that was a close match to the dimensions of our current unit, but we are thinking about downsizing to create space for a slide out pantry.

One huge disappointment is that all of the SunFrost models, including their 16 cubic foot unit, are 34.5″ wide. Our refrigerator cubby is only 33-3/4″ wide and there is no easy/practical way to modify it to make it wider. Although very expensive, the SunFrost units are super insulated and use 1/5th the energy of comparable capacity energy efficient refrigerators. They are also available with 12 VDC or 24 VDC compressors, thus avoiding the inefficiencies associated with using the inverter when boondocking.

I spent some time measuring the floor and wall surfaces in the bus that are currently tiled or carpeted but did not calculate the area. I need to do a drawing and put together an Excel spreadsheet as the bus has a lot of odd shaped spaces.

We drove to ABC Supply Co. in New Hudson to pick up samples of Certainteed Landmark Pro shingles. We had narrowed down the possibilities to three choices but needed to see them next to our brick, siding, and trim.

On the way home we stopped at Lynch Carpet in Howell to return the Armstrong tile samples and determine delivery time, which was 2-3 weeks worst case. We did not get a quote since I did not have the square footage figured out yet, but Clint made a note of the tile and vinyl grout we like.

We left the house around 4:15 PM and drove across M-59 to Rochester. The Rochester Mills Beer Company restaurant was in downtown, about five miles east of the Oakland University campus and the theatre. It was after 5:30 PM when we got to the parking lot. We did not expect Kate before 6:30 PM so we ordered a hummus appetizer plate and two beers. The hummus platter featured three different flavored hummus that were very good. Linda had a chocolate coffee tasting dark brew and I had a Framboise. Framboise is a raspberry beer that originated in Holland and tastes more like raspberries than beer. Perfect!

Kate left work at 5 PM. The drive from that part of town to this part of town is one of the worst in the Detroit area, and that is a terrible time of day to do it, but that is what she did because she did not have a choice. She stopped for flowers and a card but made it to the Rochester Mills Beer Company in time to enjoy a pizza and some beer. We had a no cheese veggie pizza with a whole wheat crust that was pretty good. Linda had a different but still dark beer for her second serving while Kate and I both had the Wit’s Belgian style beer with orange and coriander. Although much more beer-like than the Framboise, it was agreeable. Except for some “guest beers” everything at the Rochester Mills Beer Company is brewed by them. It is very local, very fresh, and very good as far as beer goes. They also feature Michigan wines, which we always appreciate seeing in a Michigan restaurant, but we were not having wine this evening.

We made it to the theatre with only a few minutes to spare. Kate got the tickets from will call as they were under her cousin’s name. We had great seats in row D just left of center. Meadow Book is not a large theatre and sitting this close to the stage made for a very intimate experience. The playbill was the musical “Meshuggah Nuns.” We were not familiar with this musical but it was delightful. The 5-member cast were all professionals, including Cindy Williams (Shirley from the Laverne and Shirley TV show) and Eddie Mekka (Carmine Ragusa from the same TV program). They all gave excellent performances but Jeanne Tinker, who played Sister Amnesia, was our favorite. When dressed in a habit one really has to act with their face and hers was very expressive. She also had the “comic” part in the cast and was very funny.

The show ended at 10 PM after which we visited briefly with Kate’s cousin, Mikeala, who is part of the theatre crew working with costuming. We chatted with Kate a while longer in the parking lot and did not get home until close to midnight.

2015/05/06 (W) Old and New

Leave a reply

The morning was devoted to Miss Madeline. She helped Grandma Linda put the toys away before lunch. Brendan arrived around noon and began packing up her stuff. They left at 12:30 PM to get her home in time for her nap.

We unwrapped the box spring mattress foundation and discovered several defects. We bought this at the Sears Outlet Center in Novi and it wasn’t very expensive. Most of the appliances at the outlet center were visibly dinged, dented, and scratched so perhaps some defects should have been expected. The plastic bag, however, was intact. The defects appeared to be the result of improper handling, but that is not to say that XPO was responsible. The bottom dust cover fabric, which is very thin and flimsy, was torn but Linda was able to stitch it back together, at least enough to dissuade the cats from climbing in. There was also a small puncture, about the size of my finger, in the top surface, which again was a very thin material. Since it will have a mattress on it we did bother fixing it. There were also smudge marks on two corners. Again, they will not be visible with the mattress and linens in place so we did not worry about them.

We had e-mails from Kate inquiring about our availability to attend the Thursday evening performance of “Meshuggah Nuns” at the Meadow Brook Theatre. That worked for us so she suggested we meet at the Rochester Mills Beer Company for dinner first. Linda checked the menu online and it looked like it would work for us, so we agreed to the plan.

We spent much of the evening doing online research for a new refrigerator for the bus. The old one is still running and maintaining the temperature fairly well, but it is rather old, not particularly energy efficient, and very loud when running. It has also been repaired twice by our friend Butch and is very difficult to service because of how/where it is installed. As often seems to happen, there were almost no new units available with the same dimensions as our current unit. One of the things we are considering is getting a smaller, 24″ wide, model and building a tall, narrow, 29″ deep slide-out pantry in the unused space.

The smaller fridge would still be a compressor based residential unit, just smaller than the current one. Linda will have to decide if that is a fair trade-off although if I stop drinking Ice brand water it would reduce the need for storage volume. Our current Jenn-Air is a side-by-side and we mostly keep milk jugs full of frozen water in there for thermal mass to help with temperature stability. With a better fridge we would not need nearly that much freezer space as our frozen foods on the bus are usually one or two pizzas, a couple of Amy’s frozen entrees (for when Linda really does not feel like cooking or going out), and perhaps a container of non-dairy “ice cream.”

The Phase Place

Welcome to the next phase (hosted by QTH.com)

Tag Archives: Refrigerator (H3-40)

2015/11/16 (M) Tiling the Cockpit, #3

2015/10/20 (T) Pop-X Pickle

2015/09/13 (N) Club Business

2015/08/21 (F) Have Fridge Will Travel

2015/08/15 (S) Steve and Karen

2015/08/08 (S) A New Bus Fridge (Finally)

2015/07/23 (R) Wrapping Up Mara

2015/07/22 (W) Chucking Junk

2015/07/10 (F) Eye of the Beholder

2015/06/18 (R) Chiseled Bikinis

2015/06/17 (W) Bakery Scraper

2015/06/10 (W) Ron and Mary

2015/06/07 (N) Too Soon, Too Late

2015/05/07 (R) Meshuggah Nuns

2015/05/06 (W) Old and New