Tag Archives: Lowes (Howell MI)

2015/08/05 (W) No Mask Wednesday

Leave a reply

Linda was up at 6 AM and left for the bakery around 6:20 AM, I think. I was more asleep than awake and did not get up until later. I wanted to do a load of laundry but needed powdered detergent which I did not have. I also needed to make a run to Lowe’s so I left to take care of my errands without making coffee or having breakfast.

I picked up a couple of 2x4s at Lowe’s that I will use to cut a pair of support arms for propping open the fixed window in the bus while we exchange the refrigerators. I was going to buy a 4’x4′ (half sheet) of plywood to cut for the base of the refrigerator alcove but did not care for the selection. I also did want to wrestle with the size and weight by myself. I will have to go back to The Home Depot with Linda to get what I need. I got my laundry supplies across the street at Meijer’s and headed home.

After unloading the 2x4s I thought I would program the remote control in my car for the new garage door opener. The procedure is very simple but much to my dismay the remote would not connect with the opener. The remote is a 3-button model made by Chamberlin, and both garage door openers are identical Chamberlin models. We have four of these 3-button remotes, one for me, one for Linda, and one for each of our children. We got the 3-button model because we have two overhead doors on our garage and plan (hope) to have a barn someday with an overhead door. All four of the 3-button remotes programmed to the large garage door without a problem and the new door opener came with a single button remote that works just fine, as did the large garage door opener. I won’t know if the problem is the opener or my remote until I can try programming Linda’s remote. If her remote will program then I know it’s my remote, but if it won’t program I still won’t know where the problem lies.

I had originally planned to mask off the interior of the bus today so I could start sanding the floor tomorrow but decided to put it off. Not only would the painter’s plastic be difficult to manage by myself, I realized that it did not make a lot of sense to tape it up in advance of doing the refrigerator swap. I was on the phone with Chuck arranging to bring our bus to his shop this weekend to take care of the refrigerators when our USPS carrier, Michelle, came to the door bearing gifts. Well, OK, they were packages, but I did not expect them until tomorrow so that made them more like gifts in my mind. One was from Amateur Electronics Supply (AES) and the other was from Morgan Manufacturing, so it was all ham radio stuff.

I went to my ham shack/office and mounted the control head for the Yaesu FTM-400 on the stand that just arrived from AES. I e-mailed Steve (N8AR) to arrange a time to test the lightning arrestor before installing it in our cable entry box. I then e-mailed Jarel to start trying to arrange a day next week to drive to his shop in Logansport, Indiana to pick up the custom walnut desk. Finally, I e-mailed Josh at Coach Supply Direct to make sure he was going to be around. I was checking out the TVFool.com website, which Steve recommended, when the art frame shop in Howell called to let us know that three of our four paintings were ready to pick up. They would have all been done but he ordered the forth frame the wrong size and had to reorder it. Linda then called to let me know she was on her way home from the bakery. So much communication, so little time.

When Linda got home we discussed going out to dinner and researched a new place that had opened in Howell. As usually happens, however, there is almost no place that serves anything we choose to eat and we ended up staying home. Linda had a couple of Boca burgers in the freezer and we had those with corn-on-the-cob and fresh fruit (peaches, nectarines, and strawberries). We eat better food, and in smaller quantities, when we dine at home.

After dinner I caught Steve (N8AR) on the radio and we agreed that I would bring the lightning arrestor over to his QTH at 8 PM. I had an e-mail related to the draft of the July issue of Bus Conversion Magazine and checked to make sure a correction had been made correctly.

At Steve’s house my lightning arrestor tested better than the previous one, and should work OK in my system, but it was very clear that there is something wrong with the design and/or manufacturing of these VHF/UHF I.C.E. units. We also came to the conclusion that the quality control testing the manufacturer was doing (if any) was inadequate to reveal the problem. I expect, however, that this one will work when I install it so if it is typical of their units most hams would not have a reason to suspect that it was flawed. Someone would have a problem with it, however, as it is clearly not usable for all frequencies from 40 MHz to 1 GHz as stated on the label. My unit has a 0.31 dB loss at 445 MHz (it should be 0.01) but has an 11.59 dB loss around 635 MHz, which is a huge factor of 16 times loos of signal, and the loss from 500 MHz to 1 GHz is unacceptably large making it useless in that range of frequencies.

Steve captured all of the data and e-mailed it to me. He then tested one of his Polyphaser lightning arrestors and sent me that data file. He also sent me the link to the VNWA software from SDR-Kits.com that I needed to work with the data file. We spent a few minutes talking about the problem we are having at home with our ham radio transmissions interfering with our OTA TV signals. He sent me a link to the free student version of the ELSIE (“L”,”C”) filter design software.

I left about 9:45 PM and called my friend, John Rauch, to see if Saturday noon would work for him in terms of our refrigerator swap. He said it would and that he would check with his son (also John) to see if he could/would also help. I will let Chuck know tomorrow that it looks like Saturday is a “go.”

Linda was asleep by the time I got home so I worked in my office until after midnight. I captured the data attached to the e-mails from Steve and then downloaded and installed both the VNWA and the ELSIE software. I then uploaded my personal blog posts for June 28, 29, and 30. I logged in to the FMCA Freethinkers website, the FMCA GLCC website, and the SLAARC website and installed updates for the themes and numerous plug-ins. With that I came back upstairs and worked on this post in the living room so as not to disturb Linda and finally went to bed around 1 AM.

 

2015/07/24 (F) Open and Shut

Leave a reply

I was up at 7:30 AM and made coffee but I did not see Mara or Linda until after 9 AM.  Around 9 AM I heard a knock at the front library doorwalls and heard someone saying “hello?,  hello?, David?”  I went out the front door and saw the front end of a red Ford Focus parked in front of our bus.  I had never met this guy but he was not unexpected and I knew he was looking for David LaVoisne, who lived here with his wife, Maria, until we bought the house from them in February 2013.  I knew this guy might stop by as he had once before when we were away and chatted briefly with our lawn care guy, Keith.  I also knew that he had worked with David at the Ford Wixom plant before they retired.

We introduced ourselves and had a nice chat.  I explained that David and Maria had sold the house and their Airstream motorhome, bought a newer motorhome, and were now full-time RVers.  (As I recall they bought a used Foretravel.)  Apparently they did not let all of their friends or former colleagues know what they were doing.  I also mentioned that they had moved the few possessions they did not get rid of to their son’s house somewhere in the region and that they probably visited there occasionally.

Mara emerged about the time our visitor left.  Unfortunately I do not recall his name.  We all had breakfast together after which Mara went about her final departure preparations.  She gave Linda a small fir tree and two small herbs.  Linda transferred the herbs to her herb pots and gave Mara’s small pots back.  She needed to top off her fresh water tank so I helped with that.  The lock on the water fill door stuck in the open position so Mara got her can of dry lube and I sprayed a little in the lock by holding the protective cover open with the tip of the key.  That did the trick, another quick fix to a small but potentially annoying problem.

When her rig was basically ready to go Mara made one last use of the shower, got dressed to travel, unplugged the power cord and stowed it away, and pulled in the slides.  After hugs all around she climbed into the pilot’s seat and fired up the engine and Sabra (one of her two cats) climbed up on the dash just in front of the steering wheel.  I guided her as she backed out onto our road.  She drove down to the court, did a three point turn, and a few minutes later drove past our house in the opposite direction, back on the road again after almost two weeks at our place.  It was noon, but she was only going as far as London, Ontario today.  Linda got a text message later letting us know that she had arrived at the Moose Lodge and the border crossing on the Blue Water Bridge from Port Huron, Michigan to Sarnia, Ontario had only taken 30 minutes.

After Mara was out of sight I gathered up the laundry, sorted it, and started a load of warm whites.  I wrote out a list of parts I needed to finish the garage door opener installation and the monitor mounting system in the ham shack and then drove to Lowe’s in Howell.

I was back home by 1:30 PM and we had hummus and chips along with black grapes for lunch.  We started working on the garage door opener installation when my phone signaled that I had a voice message.  It turned out that I had one on the house phone too.  Both messages were from Jarel.  He had a few questions about dimensions on one of desk drawings so I called him back and we sorted that out.  He retrieved the half sheet of walnut veneer plywood from Butch last night and bought 16 board feet of walnut.

In spite of the 85 degree temperature and what felt like high humidity, even though it was only 41%, we worked for about three hours and finished installing the opener on the small garage door.  It was quite an involved process but it worked when we were done.  The new opener has automatic reverse if it encounters an obstruction and an infrared sensor beam about 6″ off the floor.

At 5:30 PM we loaded the old garage door opener into the dump trailer.  We then loaded the old OTA TV antenna pieces.  Brad is picking up the trailer in the morning so we will not fill it but it we put the junk in it that we needed to get out of the garage and a few other things as well.

We took a break around 6 PM to have some water and get off our feet for a while.  At 6:45 PM Linda made salads and cooked up some vegan Italian sausages.  After dinner we planned to work for a while in the ham shack on the installation of the wall-mounted track system but we were too tired to start a project that was going to require decisions and careful attention to detail.  We sat in the living room instead and used our iPads for the usual things.  It was great having Mara here and we look forward to her return someday.  But for now she is off on the next leg of her open-ended adventure and we have a lot of work yet to do to get our bus ready for the 2015-16 winter season.

 

2015/07/18 (S) RV Shopping

Leave a reply

Madeline was awake at 7 AM and Linda got her up shortly after that.  I slept in until 8 AM.  They had already eaten breakfast by then so I made coffee and had cinnamon raisin toast.  Metropolitan Baking Company makes a very tasty cinnamon raisin bread.  We all sat in the living room while Madeline played with various toys and I worked on finishing yesterday’s blog post.

Linda and Madeline left at 10 AM for the Howell Library.  The plan was to let Madeline play in the children’s area, which has a lot interesting things to do for children her age.  After selecting some books and DVDs to bring home they were headed to Meijer’s to do some grocery shopping.

I continued working on my iPad until Mara came in the house.  We had a chat about blogging and I showed her the Feedly app on my iPad.  She has attended workshops put on by The Geeks On Tour and has their training materials.  I think Blogger is probably the right tool for her and Picasa is probably the right way to manage her photos.  They are both Google products so they work well together and they are free to use.  There are downsides to that, especially for professionals, but for most people it’s a great solution.

Mara and I left around 11:45 AM and drove to General RV in Wixom.  This was my first visit to their new facility and it is nice.  The parts department is larger and better stocked than the old one and is bright with natural light from large south and west facing windows.  We were asked several times if we needed assistance but we were never pestered.  They did not have any of the white Dicor self-leveling caulk we were looking for but one of the employees checked their stock and brought out six tubes.  Mara bought four of them along with a new Norcold refrigerator roof vent cover, a small roll of Eternabond tape, and some concentrated RV wash/wax.  I picked up eight brown circular adjustable air vents for the bus.  The ones in there now are black but I think the brown will look better with the new floor tile.  We won’t really know, however, until we install them.

We drove to Lowe’s in Howell where I bought two pieces of 12″ x 18″ thin galvanized steel plate and three rolls of 3M double-sided tape suitable for outdoor use.  The plan is to put one of these on the roof of Mara’s motorhome and possibly put the other on the roof of our bus to allow the use of the magnetic base cell phone antennas that came as part of the weBoost Drive 4G-X cellular booster systems.  Once the steel sheets are affixed to the roof I will caulk around them.  First, however, I will just set the sheets up there and see what sort of difference the system makes.

We stopped at O’Reilly’s auto parts store and Mara bought some 10, 15, and 20 Amp mini fuses.  These fuses have a small LED that glows if the fuse opens.  They were more expensive than the regular ones, but that is a very handy feature and I may stock up on these the next time I need to buy fuses.

Back at the house Linda informed me that when the storm blew in it pulled the sun umbrella out of the table on the deck.  We put the glass top back in the table and re-installed the umbrella.  This has happened a couple of times and we have been lucky that the glass top has not broken.  Mara returned to her rig.  She had left her patio awning out but it was not damaged.

Linda got Madeline up from her nap at 3 PM and read her a story about flying in an airplane.  Madeline then played with her toys for a while.  Around 4 PM Madeline wanted to bake a cake.  Linda was planning on this anyway but it was nice that it was Madeline’s idea.  They got busy in the kitchen and I sneaked off to my office for a while.

Madeline had dinner at 6 PM so I came up from my office while she ate.  Meals are a social time and I was ready for a break anyway.  After dinner Linda helped Madeline get cleaned up.  I slipped back down to my office while they watched an Elmo DVD, but by 7 PM I was done working on the pantry design for the evening and went back upstairs.  Linda was reading the airplane ride book (again), after which Madeline played (with) the organ after which they drew for a while and then played with the Play-Doh.  Madeline is a busy girl.

I was just getting ready to go ask Mara what temperature to preheat the oven when she came to the house with an armful of ingredients for the pizza.  She has a recipe for a wheat-free (gluten-free) pizza dough that she wanted us to try.  It calls for cheese and eggs so to make it vegan Linda had her buy Daiya mozzarella shreds and gave her egg replacer to use.  The other ingredients include almond meal, chickpea flour, golden flaxseed, onion powder, garlic powder, sea salt, olive oil (EVVO), and water.

It took another 25 minutes to get Madeline to bed but once Linda had her tucked in I opened a bottle of Nebiola wine from the St. Clair Winery in Deming, New Mexico.  I often write that I am not a fan of red wines and continue to not like dry wines with lots of tannins.  The Nebbiolo, however, is one of the nicest wines I think I have ever tried.  That probably means it is too sweet for most red wine drinkers, but I did not find it to be sweet; I found it to be smooth and complex.

We ordered a couple of things from Amazon on Wednesday and they showed up yesterday.  When I unboxed the Notier capacitive touch screen precision stylus I was surprised by what I found.  It’s a 2-part housing that unscrews and the cover screws onto the other end of the bottom part, which is needed for comfort and balance.  The stylus tip is small but has a 1/4 in clear plastic disc on the end.  It was on sale for $11 and I decided right away I would not return it.  Besides, I had not actually tried it yet.  So I finally tried it while the pizza was cooking.  It is an amazing little device!  It is, indeed, very precise and works with a delicate touch so I will have to re-calibrate my “typing” style, but it just goes to show that you never know until you try.

I lost track of time but it was somewhere between 9:30 and 10 PM when the pizza was ready to eat.  It was, however, worth the wait and might be the best vegan pizza I have ever had.  The recipe is definitely a keeper.  We each had a chocolate cupcake (with sprinkles) while we finished our wine.  We then adjourned to the living room and talked until almost 11 PM.  It was a very full day for all four of us and everyone was tired but satisfied.  It’s nice having family and friends here.

 

2015/07/12 (N) Mara Comes To Visit

Leave a reply

When I shut down the bus yesterday I forgot to shut off the air supply to the engine accessories and turn off the chassis batteries, so I did that as soon as I got up this morning.  I then made coffee and we had our usual juice and homemade granola.  After breakfast Linda went shopping and I went to Lowe’s.  She picked up a lot of fresh vegetables at the Howell Farmers Market and finished up at Meijer’s.  I bought a 4-piece screw extractor set and then stopped at O’Reilly’s and bought two gallons of 50/50 pre-mixed universal antifreeze to top up the Aqua-Hot in our bus.  I stopped at Teeko’s Coffee and Tea and had them roast a pound of Sumatra Mandheling beans.  We have not tried these before but Mary thought we would like them.  They are not decaffeinated, but we try to keep a regular coffee bean on hand for company, after dinner, or when we want (need) the high octane in the morning.

Linda had been in contact with our friend Mara for the last few weeks so we knew that she might stop here on her way to the Canadian Maritime Provinces.  Late last week she confirmed that she would be here on Sunday so after our morning errands we turned our attention to getting ready for her arrival.  She lives/travels in a Fleetwood Bounder (Class A motorhome).  We saw it in Quartzsite, so we knew it was somewhere between 35 and 40 feet in length and that she does not tow a car behind it.  Yesterday we moved our bus so she could park on the level pad with easy access to our 50 Amp electrical hookup.  I cleaned up the coaxial cables that I had spread out all over the rec room floor and Linda vacuumed the carpets and wood floors and cleaned the bathrooms.  We keep a clean house but it is not always tidy as we are involved in a lot of projects at the moment.  But when company is coming we like things to a least start out tidy.

Mara was coming from Michigan City, Indiana so she only had 200 miles to travel.  Most of it would have been on Interstate highways but she decided to detour over to Three Rivers, Michigan to visit a Latvian community located nearby.  She finally arrived at our house around 2:30 PM.  We met her in the street and I directed her into her parking spot.

It’s always exciting, and a bit intense, to meet up with an RV friend and that was certainly the case here.  Mara had enjoyed her stop at the Latvian community even though she found them in church.  We had last seen her in Quartzsite, Arizona in February.  We had all had a lot of RV travel adventures since then, and it was also her first visit to our house, so we had lots to talk about.

Linda made bow-tie pasta with mushrooms, onions, garlic, sun-dried tomatoes, and basil pesto using basil that she grew on our back deck.  We had a simple green salad and Italian bread with the meal and enjoyed 1-1/2 bottles of the 2013 Egri Merlot between the three of us.  We sat on the deck enjoying the last of the wine until it cooled off and we went inside.  By 9 PM we were all tired but we insisted that Mara stay for fresh sweet cherries.  Rejuvenated by the cherries we all got our second wind and had a long conversation about RVs, cellular and Wi-Fi communications while traveling, and a cool routing app that Mara uses (MapMyPlaces).  By 11 PM we were all tired for real and Mara returned to her rig for the night.  It had been a long, but very satisfying, day for all of us.

 

2015/07/03 (F) 4th Anniversary

Leave a reply

Several SLAARC members were gathering at 10:30 AM this morning to unload the Field Day equipment from Steve’s trailer and store it in the South Lyon water tower.  I was going to join them but decided last night to stay home and work on the design for the desk and HVAC chase covers for our motorcoach.  Having played ham radio for much of the last week and a half I needed to refocus my time and attention on the interior remodeling of our bus.  Besides, Brendan was bringing Madeline to our house sometime mid-to-late morning and I wanted to be home when they arrived.  Today was Brendan and Shawna’s 4th wedding anniversary and they asked Linda if we would take care of Madeline for a couple of nights so they could have some time together without the constant demands of child care.  Of course Linda said ‘yes.’

I had a call last night from XPO Delivery Services letting me know the new refrigerator for the bus would be delivered to Chuck Spera’s shop in Novi today between 6 and 8 PM.  That meant I would have to be at the shop by 5 PM just in case they arrived early and could be there past 8 PM if they arrived late.  At 7:45 AM this morning I got a call from the Lowe’s in Howell asking if XPO could deliver the refrigerator in about an hour.  Sure, why not; I was still in bed but about to get up anyway and having the refrigerator delivered early would actually open up my entire day.  I hurried the process along, had Linda get the receipt, grabbed my iPad, and headed for Chuck’s shop in Novi.  Linda was getting ready to go for a walk as I left.

One never knows what the traffic will be like on I-96 headed into the Detroit metro area from the northwest but on this Friday, at the start of a major holiday weekend, the traffic was very light and I was able to get to Novi in the minimum legal time.  Traffic headed westbound actually appeared to be heavier than the inbound traffic.  I stopped at the Tim Horton’s on Beck Road just north of Grand River Avenue and got coffee which I had not taken the time to make at home before I left.

I texted Chuck to let him know that the refrigerator was being delivered this morning.  He called me back to clarify where to have them set it.  This would be a great weekend to do the swap as all of the other businesses around his shop building will be closed for the holiday, making it easy to get our bus in and out.  But his daughter arrived last night from New York and will be visiting for a week so the refrigerator replacement will have to wait, probably until at least next weekend.

By 9:30 AM XPO had not arrived so I called Lowe’s in Howell and talked to Erica in scheduling.  She said she would call the driver and see what was going on.  I texted a status update to Linda and continued to wait.  By 10 AM there was still no truck and no call back from Erica.  At 10:20 I was dialing Lowe’s again when an Enterprise rental truck drove past the building headed east and a few minutes later went by headed west and pulled into a parking lot.  Moments later my phone rang.  It was the XPO truck driver.  I explained where the driveway was and flagged them in.  When I ordered the fridge I gave detailed special instructions on how to find the building but the driver did not bother reading them and did not bother calling me until he had failed to find the delivery location for the second time.

They backed the truck into the area in front of Chuck’s garage door, lowered the refrigerator down on their lift gate, slid a pair of lift straps under it, picked it up, and carried it into the shop.  I looked it over as best I could and then signed for it.  Only later did I notice a small dent towards the bottom of the door.  I had an automated call later asking if I was satisfied with the delivery and indicated ‘no’, noting the arrival delay and the small ding.  The message said I would hear back from someone within an hour but no one ever called.  We do not plan to make an issue of the ding as we will be lucky to get it into the bus and into its alcove with no further damage.  Still, it should have arrived in perfect condition and did not.

I called Linda to let her know the refrigerator had arrived and that I was getting ready to head home.  She said Brendan had just arrived with Madeline.  As I started to back out of my parking spot Chuck arrived so I spent about 30 minutes talking with him about the timing and approach of the refrigerator swap.  I will almost certainly take our bus to his garage on a weekend.  Only later did I find out that Brendan will not be available to help for the next two or three weekends.  Ugh.  Chuck called a friend (golf buddy) who has narrow pallets (24″) to see if he could get a 5’ long section.  With the long forks set close together on his forklift we can slide the pallet over the forks and have a much more secure platform form for raising and lowering refrigerators, probably laying on their backs.

Linda called back and asked me to stop on the way home for some toddler toothpaste and a toddler toothbrush.  I did not know they made such things but I found them at the CVS in Brighton.  Not long after I got home Linda had lunch on the table.  She heated some veggie nuggets and set them out along with baby carrots, grapes, pretzels, hummus, vegan deli slices, bread, lettuce, and onion.  We all had a good lunch with lots of variety.  Brendan got Madeline down for her nap at 1 PM and hung around long enough to make sure she was asleep.  I took a few minutes to show him the new Yaesu radio before he headed back to Ann Arbor.

I was very tired and took a nap on the living room sofa which is especially comfortable for this purpose, better actually than for sitting on.  Madeline slept until almost 4 PM.  When she woke up she wanted her mommy and daddy and was a little weepy but Grandma Linda got her quickly engaged in doing things.  Linda took her for a walk to see the chickens while I went downstairs to check e-mails.  I responded to ones having to do with the transfer of the SLAARC website and domain name registration from GoDaddy.com to QTH.com and made mental note of others.  When they got back from their walk Linda brought Madeline downstairs to see Grandpa Bruce at work in his office and ham radio shack.  We told her we would help her become an amateur radio operator when she was older.

Linda decided that baking a vegan chocolate cake would be an excellent activity to do with Madeline and give us a nice treat for later.  Madeline helped pour and stir ingredients.  She ended up with chocolate cake batter on her face and clothes but it was worth it as she got to lick one of the spoons.  (Without any animal products, especially raw eggs, vegan cake batter is perfectly safe to eat.)  Linda had previously found a small baking set for Madeline that included a small bunt cake pan.  Some of the batter went in there to make a little cake just for Madeline and the rest was used to make 11 cupcakes.

After the cupcakes were cooked and taken out of the oven to cool Linda made dinner.  We had mock chicken strips (vegan), fresh sautéed green beans, vegan refried beans, and fresh berries leftover from earlier.  When the cakes were cool enough Linda got out the powdered sugar and sifter and we dusted them.  Madeline enjoyed the decorating but somehow ended up with powdered sugar in her hair, on her dress, and all over her face.  I took pictures and then Linda cleaned her up while I cleaned the floor.

After dinner and dessert we played and read a bit.  Linda had gotten three Sesame Street Workshop DVDs from the Howell Public Library so we all climbed up into the bed in our bedroom and watched one of them.  We played along with the various activities and games and encouraged Madeline to do the same.  The program ended at 8 PM which is Madeline’s bedtime.  Linda helped her in the bathroom, got her into her pajamas, and helped her brush her teeth.  She laid down without a fuss and drifted off to sleep. We stayed up until the last chime of the grandfather clock at 9:45 PM and then turned in for the night.  We are always satisfyingly tired after a full day of Madeline.

 

2015/07/02 (R) 100,000 Radios

Leave a reply

We were tired and did not get up until almost 8 AM.  Linda prepared a tofu scramble for breakfast, as we were almost out of her homemade granola, and served it with some cinnamon raisin toast and fresh grapefruit.  It’s the closest thing we eat to scrambled eggs and she serves it as an occasional change of pace from our standard granola breakfast.

I had my annual appointment with my dermatologist this morning at 11 AM.  I needed to pick up a cable from Scott (AC8IL) at Adams Electronics, which was on my way to the Henry Ford Health System (HFHS) clinic, so I left the house a little after 9:30 AM.  The drive was fine initially and I had a nice QSO (chat) with Steve (N8AR) on the South Lyon 2m repeater.  As I was approaching Wixom Road, however, all lanes of eastbound I-96 were stopped.  I was able to exit at Wixom Road and headed north a short distance to West Road which I took east over to Beck Road where Scotty’s business is located a little north of West Road.  I had a brief chat with Scott about the antennas on my tower before I left.

Two miles north of Scott’s shop I turned east on Maple Road (15 Mile Road).  The HFHS has many clinics around the greater Metro Detroit area and my dermatologist is located at the intersection of Maple and Farmington Roads in West Bloomfield.  That should have been an easy trip but there was construction on Maple Road that had the road down to one lane with flaggers.  There were signs advising motorists to seek other routes but I did not heed the warning.  I patiently worked my way through and arrived for my appointment about seven minutes ahead of time.  Good thing I left as early as I did.

My exam was fairly routine and Dr. Nydorf wrote out a prescription for Doxycycline.  I will try taking it (again) three times a week and see if it helps.  I headed straight for home after my appointment but took a different route.  Once I was back at the house Linda went for a walk.  While she was walking I removed the license plate from her car, took the protective (anti-theft) cover off, and cleaned everything.  When it was dry I put the new registration sticker in the corner, reassembled the cover, and installed the plate back onto the car.  I then started working with the various pieces of the new Yaesu FTM-400DR/DE mobile radio.  When she got back from her walk she heated up a couple of tofu hotdogs for lunch.  These are such simple fare but so tasty (with mustard, onions, and relish) and so appropriate for a summertime lunch.  They are also a really easy lunch to get on the table.

After lunch Linda took her car to the Howell library to get some books and children’s DVDs and then stop at the Meijer’s supermarket to pick up a few grocery items for Madeline’s visit this weekend.  While she was running errands I assembled our new Diamond X-300NA antenna.  Once it was assembled it was over 10 feet long so I stored it by mounting it to the side of the tower.  I put it up as high as I could reach from the ground to get the three counterpoise (elevated ground plane) rods above eye level.  Moving it to the top of the tower as a replacement for the Diamond X-50NA will have to wait until next week or later.  The exact timing will depend on the weather, Mike’s (W8XH) availability, and whether I have acquired appropriate standoffs by then for the X-300 antenna and/or the cellular booster omnidirectional antenna.

With the antenna taken care of (for now) I disconnected the coaxial cable for the X-50 from the radio side of the lightning arrestor and positioned it so I could pull it back into the sump pump room.  From there I fed it into the ham shack, disconnected it from the radio, and coiled it up.  I uncoiled the new 20′ LMR-400 cable with the N-male connector end positioned so I could feed it through the corner of the ceiling in the ham shack (by the ground wire) and into the sump pump room.  From there I fed it through one of the 2″ conduits into the cable entry box.  Back outside I shaped the cable (LMR-400 cable is double shielded and stiff) and connected it to the radio side of the Morgan VHF/UHF lightning arrestor and closed the lid on the box.

Back in the ham shack I attached the PL-259 connector to the SO-239 socket on the back of the Icom IC-7000 GoBox.  I could have gotten away with a 16′ cable but the 20′ length gives me more flexibility with respect to equipment placement.  I turned on the IC-7000 but did not hear anyone on either the South Lyon 2m or the Novi 70cm repeaters so I turned it off.

I disconnected Mike’s Icom IC-2820H and set it aside to make space for the new Yaesu FTM-400DR/DE dual band mobile transceiver.  I moved the new coax to the new radio, powered it up, spent a few minutes configuring some basic things, and then listened to the South Lyon and Novi repeaters.  I tried calling them but was not triggering them so I knew the PL Tone was not set correctly.  I called Mike for assistance and left him a voice message.

Linda was back by this time so she came down to see the new radio.  We then went out to the bus to make our final decisions about upholstery fabric and window shade materials.  In the end we chose the Lambright Notion Linen fabric for all four chairs and the MCD B50 material for the dark out shades.  We brought all the samples back in the house and I e-mailed our choices to Josh at Coach Supply Direct.

I had an e-mail from Scott Neader (KA9FOX) at QTH.com requesting an admin login for the SLAARC WordPress website so I set that up and e-mailed him back.  I had the new radio on and was listening to a conversation on the Novi repeater.  It had just concluded when Mike returned my call.  He walked me through how to set up the PL Tone and Squelch Tone for both of the repeaters on the FTM-400.  We were then able to verify that the radio was working on both bands.

For dinner Linda made a salad and pan-grilled tofu with caramelized onions and barbecue sauce which she served open-faced on hamburger buns.  We had watermelon for dessert, which we have been doing a lot this summer.  I did not care for watermelon as a child but it has become a favorite summertime treat.  I had dropped a small lock washer while mounting the new antenna to the tower earlier so I went to Lowe’s to get a replacement and some spares.  On the drive there I got a call from XPO Delivery Service letting me know that the new refrigerator for the bus would be delivered to Chuck’s shop in Novi tomorrow between 6 and 8 PM.

At Lowe’s I picked up some 6mm x 1.0 Nylok nuts in addition to the lock washers.  I also got some grass seed patching mix, a few more bags of decorative broken brick pieces, and a hummingbird feeder with a red reservoir so Linda can use sugar water without red food coloring.  When I got home the odometer on my car read 100000 so I took a picture of it with my phone.  I then spread the patching mix over the bare dirt I had used to fill a hole and troughs left by the installation of the natural gas line to our house last September.  The rest of the evening Linda read and I worked on completing drafts of blog posts.

 

 

2015/06/25 (R) The Mouse

Leave a reply

Brighton Honda called yesterday in the afternoon to get permission to do additional work on my car.  Since we plan to keep the car for a while, and then perhaps give it to our son, it was the kind of work that needed to be done regardless of the costs.  They called back later to indicate that they would not have it aligned before closing time.  That was fine with us as it would have been inconvenient to impossible for us to get there by 6 PM to pick it up.  Linda told them to call in the morning when it was ready.

The top of the 40-foot tower from the WNW showing all of the antennas and the pulley with the haul rope. The weather had definitely deteriorated from the day before.

The top of the 40-foot tower from the WNW showing all of the antennas and the pulley with the haul rope. The weather had definitely deteriorated from the day before.

It is amazing how attuned we become to routine sounds and how sensitive we are to non-routine ones, even (especially?) while sleeping.  So it was last night that I was suddenly aware that one of our cats was making a repetitive sound that was unusual.  I turned on my flashlight, hoping to not disturb Linda, and got out of bed.  Both cats were hunched down on the floor on Linda’s side of the bed with Jasper in front.  He was the one responsible for the sound and the reason was next to his head and about 3 inches away; a little dark gray mouse.

My first thought when I see one or both of the cats with a mouse next to them rather than in their mouth is that it is dead but that was not the case.  This mouse was alive and apparently not injured.  I have seen this behavior before in which the mouse basically “plays dead” and the cats leave it alone but watch it carefully.  Mice seem to know that cats are triggered by movement and that if they sit very still the cats just sit there and guard them.  It was 4:30 AM and I was not fully awake so I do not recall the exact sequence of events, but the mouse somehow ended up in our master bathroom.   I do not recall what I did with the cats but I think I went and got a box with high sides and tried to get the mouse to go in it and it made a run for it towards the bathroom.  Linda was awake by this point so she got a towel for me.  I went in the bathroom and used the towel to block the gap under the door and prevent the little critter from getting back into the bedroom while I tried to get it into the box.  I was unsuccessful and it managed to find a place to hide in the hot water baseboard radiator.

Linda got one of the live traps we recently purchased and baited it with the recommended saltine and peanut butter.  We set the trap near the radiator, turned out the bathroom light, shut the door, and tried to plug the gap with the towel from the outside, figuring we would deal with the mouse in the morning.  Juniper kept pawing at the towel and pulling it back from the door so we put both cats out of the bedroom and shut the door.  They found that confusing as they sleep with us and generally have the run of the house.  One or both of them pawed at the door meowing to get back in for quite a while.  It wasn’t the best night’s sleep we have had and the timing was unfortunate given the hard day of tower work.

Brighton Honda called at 8:01 AM to let us know the car was ready.  Hello, I’m awake now!  I checked on the mouse and it was now safely tucked away on top of the radiator fins inside the housing where neither the cats nor I could get to it.  We decided to leave the live trap in place, sealed the gap under the door, and kept the bedroom door shut to keep the cats out.

I had planned to drive to Isringhausen’s U.S. headquarters in Galesburg, Michigan today but first we had to get my car.  As long as we were headed that way we decided to go to the Brighton Panera for coffee, but had toast and juice for breakfast at home before we left.

The 100,000 mile service is extensive and includes changing the spark plugs.  Beyond the routine service items the Element needed a new ball joint and tie rod and had a stuck brake caliper pin that had to be repaired.  Given the front end work I also had them align it.  Butch and I rebuilt the front brakes last year so I was surprised that there was an issue with them, but the car has been towed and driven in some harsh environments since then so that may have been a factor.

The Panera at Grand River Avenue and I-96 is not one of our favorites.  More often than not we end up with coffee grounds in our cups and the bathrooms are not maintained as they should be.  Today was not the first time we have been to this location that the men’s restroom was out of toilet paper.  It is also often freezing cold inside the restaurant and today was no exception.  The weather was overcast and a bit gloomy but the outside temperature, while not warm, was much more comfortable than inside.  We were also unable to connect to their Wi-Fi signal, which is generally useable.  That’s pretty basic stuff to not be able to get right and falls squarely on local management in my opinion.

While we drank our coffee I called Rick Short at ISRI to make sure he would be in but I got his voice mail again.  I asked for a call back but never got one so I did not make the trip to Galesburg.  Apparently they have better things to do than be of assistance to me.  I only want to buy one chair, not a fleet of chairs, so I understand my relative unimportance, but I don’t like it just the same.  We decided to spend the day at home completing the work from yesterday, which had made a mess throughout the house.

One of the things we needed to do was register our cellular booster system.  Given that it is a five band device I was not clear on whether we had to register it only with Verizon or with all of the carriers.  I called the company we bought it from, Cellular Solutions, and talked to Judy who said we only had to register it with the carriers we personally use.  For us that is Verizon Wireless.  Registration was via the Verizon Website and was simple enough.  It did, however, require me to log in to our My Verizon account and navigate through a couple of screens to a page where we could enter the information from the label on the box.  The serial number was on two peel off tags, so one of those went on the booster and the other one went in the manual.

With the unit registered I turned the power switch on and watched the ‘Alert’ lights all go solid yellow.  As I mentioned in yesterday’s post solid yellow lights are not described anywhere in the manual.  I called Cellular Solutions back and said I had a technical support question.  The woman on the phone took my name and number and said someone would call me back.

Since I was apparently taking care of phone chores I decided to call Universal Towers and inquire about their B-30 base.  The woman who answered the phone never gave her name but was able to answer some questions.  She indicated that their base might or might not be compatible with older Heights Tower products, depending on exactly which product I had, and that I would have to talk to the owner, Bill, who wasn’t there at the moment.  She did know that the outside-to-outside measurement of the legs on a B-30 base was 30 inches and the base cost $290.  She also told me that the larger bases, like the B-30, consisted only of the three rods with the mounting yokes on top; the three rods were not otherwise connected together in any way.  She also confirmed that the ‘U’ shaped yokes at the top of the base rods were welded on and not adjustable.  The normal installation procedure involved connecting them to the bottom of the legs of the first section of the tower, setting them in the hole as the concrete is poured, and adjusting them by moving them around until the legs of the tower were plumb.  That sounded to me like a process where a lot could go wrong and not be repairable.

I pulled a 75 ohm coax out of the ceiling of the basement yesterday.  We laid it out in the basement to see how long it was and it looked to be at least 60 feet.  Linda suggested we test it before running it through the basement ceiling which was a very sensible idea.  I unplugged the power adapter for the TV amplifier power inserter, detached the coax that feeds the TV in the bedroom, attached the downstairs cable, and connected the other end to the basement TV set.  Linda set up the TV for Antenna input, did an All Channels scan, and got the same stations we got yesterday, minus a couple.

In spite of what appeared to be acceptable performance I decided I wanted a new coax cable and Linda wanted to return three of the ropes I bought at Lowe’s but never used.  She found the receipt and we went to Lowe’s.  They had a good quality RG-6 quad-shield coax (75 ohm) in various lengths including 50 feet, which is what I needed.  At the register I decided to buy two more 40 pound bags of solar salt.  I am not an impulse shopper as a rule but their supply of Morton Solar Salt was very low and stocking up seemed like a good idea.

We stopped at Teeko’s to order coffee.  Mary took our order and rang it up; one pound each of the three different half-caff blends that have become our standard.  We took note of the fact that the Bennigan’s restaurant building on the northwest corner of Grand River Avenue and Latson Road was gone and a sign said a Panera would be coming soon to that location.  We didn’t say anything to Mary, but that cannot be good news for Teeko’s.  We will continue to buy our custom roasted beans at Teeko’s as long as they are open but it is going to be difficult for them to compete with a $2.25 cup of bottomless coffee, free Wi-Fi, a restaurant, a bakery, drive through service, and ample parking with great access to I-96.

When we got home I checked the live trap in our master bathroom and we had captured the mouse.  We took the trap to the northeast corner of the property, towards our neighbor’s pond, and set it free.  It did not want to leave the trap and I had to encourage it to go.  Once it hit the ground, however, it scampered away looking for a place to hide.

We then worked on running the new coax from the basement TV to the sump pump room above the suspended ceiling.  I disconnected the power inserter for the amplifier and disconnected the old coax we had tested earlier.  I notched a ceiling panel at the corner of a boxed support column behind the basement TV to allow the ceiling tile to go back into place around the coax.  We then installed one of the wire channels to contain and hide the coax from the ceiling down to the TV set and connected it to the back of the set.

In the sump pump room I attached the coax from the cable entry box (CEB) to the input of the new 1-to-2 signal splitter.  I attached the coax for the bedroom TV to one output from the splitter and the coax we just ran to the other output.  I mounted the splitter on the wall of the sump pump room and secured the cable coming from the CEB to the ceiling.  I then plugged the power supply for the power inserter back in to an AC outlet.  Linda scanned for channels and verified that everything was working correctly.  We then installed the other wire channel alongside the trim on the bedroom doorwall to route and hide the cable coming up from the basement.

I continued to fuss with the cell phone booster gain settings.  We had not gotten the promised return phone call from Cellular Solutions Technical Support so I called them.  I got Judy again and explained what I was seeing with the solid yellow lights.  She checked with her tech support people and they said the manufacturer (SureCall) told them the solid yellow was the same as the blinking yellow; that the booster was adjusting the gain and it was “normal.”  The manual says that normal is when the light is off, so I’m not sure I buy this explanation, but based on that I left the booster turned on.

With all of that done we started cleaning up the tools and materials we had scattered over two floors of the house.  I decided that was also a good time to start a load of laundry, although it was actually rather late in day for that.  I did three loads by the time I was done and it was sometime after 10:30 PM before the last load was dry.  I needed to be up at 7 AM to be at breakfast in South Lyon at 8 AM as our SLAARC group would start setting up for the ARRL Field Day event at 9 AM.

 

2015/06/24 (W) Up The Tower

1 Reply

Today was the day to finally climb the tower to remove an old TV antenna, reposition an amateur radio antenna, and install two new antennas, one for OTA TV and the other for a cellular booster system.  But there were other things to do before I was ready to climb.

I was up at 7 AM and on my way to Lowe’s in Howell by 7:20 AM in search of a solution to the problem of how to mount the outdoor cellular booster antenna.  I ended up buying two 2-1/2 inch U-bolts.  Although the tower legs are 1-5/8″ in diameter the angle bracket attached to the bottom of the antenna is 2-1/4 inches wide.  Thus I needed the 2-1/2 inch spacing for the threaded ends of the U-bolt to clear the bracket.

Back at the house Linda was up and had the coffee made.  We had a quick breakfast of homemade granola.  I removed the tire pressure sensors and GPS from my car and headed to Brighton Honda to drop it off for its 100,000 mile service appointment.  Linda arrived at the dealership about 10 minutes later.  We then headed to Adams Electronics in Wixom.  While Adams Electronics primarily serves the public and business communications markets owner Scott Adams, AC8IL, is a long-time ham and a member of the South Lyon Area Amateur Radio Club and Novi Amateur Radio Club.  Well known in the local amateur radio community, Scotty is the local go-to guy for certain kinds of equipment.  I ordered two coaxial cables from him the other day and we were here to pick them up.

We left to return home at 10 AM so I called Mike (W8XH) to let him know we were running a little behind.  So was he, but thought he could be at our house by 11 AM.  That gave me time to drill a hole in each of the two U-bolt retaining plates and cut a short piece of 1″ square aluminum tube to use as a spacer.  That was the last fabricating I needed to do and we got busy staging all of the materials we were going to need to get the tower work done efficiently.

Setting up the tools and parts outside the "drop zone" of the 40-foot tower on the east end of the house.

Mike (W8XH) setting up the tools and parts outside the “drop zone” of the 40-foot tower on the east end of the house.  (Photo by Linda)

Linda set out a sheet near the tower but not in the “drop zone.”  We spread out materials and tools on the sheet and used it to make sure we could find things quickly and keep them from getting lost in the grass.  I also brought all of my tool boxes to the tower area.  With everything assembled it was time to climb.  I set up our 7 foot step ladder on the east end of our rear deck to provide access to the roof near the tower.  Mike helped me into his climbing harness and got it adjusted.  Once on the roof I took the harness off temporarily as my first task was to remove the 2m/70cm base station antenna.  After clipping the plastic cable ties I lowered it down to Mike while Linda took photographs.  (She helped with many aspects of the work today but was the only photographer.)

Starting up the tower from the roof of the house. (Photo by Linda)

Starting up the tower from the roof of the house. (Photo by Linda)

I put the harness back on and Mike tossed me one of the 100 foot ropes which would eventually be used to haul materials and tools up and down the tower.  I secured the haul rope to one of the unused seat clip rings and Mike instructed me on how to secure the harness while climbing.  I put the waist strap around the tower and clipped it in.  I then put one of the two fall cables, attached to the ring at my upper back, around one of the legs above one of the cross bars above my head and clipped it into the ring at my chest.  The tower is adjacent to the east end of the house and is attached to it by two pipe assemblies just below the soffit (the house has hip roofs) so it was easy to step onto it.  After that things got tougher.

The horizontal trussing on the tower is two feet apart vertically.  That spacing was right at the limit of how high I could lift my right foot and required me to pull myself up part way until I could push with my right leg.  Once up on the next rung I attached the other fall cable, moved the first one higher, and slide the waist strap up to position myself for the next step.  I repeated this pattern with the two fall cables and the waist strap as I worked my way slowly up the tower, clipping old plastic cable (zip) ties as I went.  The tower definitely had some give but I was quickly acclimated to the amount of sway and found it to be acceptable so we decided not to guy the tower with the other three ropes, which would have slowed my ascent even more.

When I finally reached the top of the tower I untied the haul rope, looped it over one of the southeast facing horizontal bars and hauled it up allowing the free end to lower down to the ground.  Mike then tied the rope to the standoff pulley I had fabricated and hauled it up to me.  I already had cable ties, a diagonal cutter, and a pair of slip pliers with me.  I set the threaded rod on the northeast and southeast cross bars, inside and against the two legs that were parallel to the side of the house, and secured it with cable ties.  This was a three-handed job that I had to do with two hands but I got it done while only dropping one cable tie.  With the pulley rod secured I undid the rope and then undid the knot tying the two loose ends together.  I fed one end through the pulley and retied it to the other end.  We now had a way to haul materials and tools (in a bucket) up to me at any needed height while keeping it 18 inches away from the tower.

Three-quarters of the way up ad working with the haul rope. (Photo by Linda)

Three-quarters of the way up ad working with the haul rope. (Photo by Linda)

The next task at the top of the tower was to remove the old TV antenna, mast, and rotor.  When I finally had a close up view of these old components it became apparent that my best course of action was to try and unclamp the base of the mast from the rotator, lift it off of the rotator, and toss it to the ground.

The mast clamp parts were all very rusty so Linda got the WD-40 and Mike sent it up in the bucket.  I sprayed the nuts on the mast mounts and also the rotator leg clamps.  I tried undoing the mast clamps with a slip pliers but it was no good, so Mike sent up three open/closed end wrenches.  One of them was the right size and to my surprise the rusted nuts broke loose and started backing off.  One of them did not want to come off but unscrewed the entire bolt instead.  Fine.  The bolt had a screwdriver slot in the top and was threaded into the rotor housing and I did not care how it came out as long as it did.  I got the mast clamps loose enough that I could work the bottom of the mast free from the top of the rotor.  There was a lot of rust there too.  After clipping some coax cables, rotor control wires, and plastic cable clamps I repositioned myself up one rung on the tower so I could get enough leverage to the lift the mast clear of the rotator collar and control it well enough to make sure the antenna fell to the ENE away from the house and my helpers down below.  And that is exactly what happened.

The first antenna to get mounted was the outdoor antenna for the cellular booster system.  Mike sent the antenna up in the bucket along with the various pieces I needed to secure it to the short top/center mast support tube so the entire antenna, which is omnidirectional, was above all parts of the tower.  What would have been an awkward assembly on the ground took on added difficulty 40 feet in the air but I got it secured with good access to the N-female connector on the bottom.

At the top with the pulley in place and using it to haul up a bucket with tools and parts. Mike is controlling the haul rope on the ground. (Photo by Linda)

At the top with the pulley in place and using it to haul up a bucket with tools and parts. Mike is controlling the haul rope on the ground. (Photo by Linda)

We decided to run the coax on the outside of one of the tower legs rather than down the inside of the tower.  Mike tied the LMR-400 coax to the rope and hauled it up to me.  In addition to the haul rope Mike tied a second control line to the bucket to keep it from swinging all over the place.  I connected the coax to the antenna feed point and then wrapped the connection with coax seal tape.  I then routed the coax down the east leg of the tower and zip tied it to take the weight off of the antenna connection.

Next up was the 2m/70cm amateur radio base station antenna, often referred to as a 2m/440 dual band antenna.  (In this nomenclature the “2m” refers to a range of wavelengths for one of the VHF ham bands and the “440” refers to a range of frequencies for one of the UHF ham radio bands, so it is a mixed units designation.). The antenna is about five feet long with three short counterpoise (ground plane) rods near the base.  It had an LMR-400 style cable connected to it but with PL-259 male connectors on each end.  The antenna feed point is an N-female connector so I had an adapter installed to make everything compatible.  Mike removed the coax and the adapter, zip tied the antenna to the haul cable at three points, put the 10mm wrench in the bucket, and hauled it up to me.

The ham radio antenna was also tricky to get mounted.  I installed it at the top of the northwest leg so that most of the antenna was above the tower and two of the three short counterpoise were parallel to the west (N-S) and northeast (NW-SE) crossbars.  The antenna by itself is light in weight but it is five feet long and mounts at the bottom nine inches, so most if it was above me with a tendency to wave around in mid-air.  With the coax connected, however, it weighed quite a bit more.  I temporarily zip tied the coax to take the weight.  I then had to hold the antenna with its base against the northwest post at my head level, push a U-bolt through the mounting bracket and past the tower leg, slip the mating clamp over the two ends of the U-bolt, and then get a small lock washer and nut on each threaded bolt end.  I then had to repeat this for the second U-bolt.  Again, a three-handed job that I had to do with only two hands.

The old OTA TV antenna and mast on the ground. It came down by the gravity method. (Photo by Linda)

The old OTA TV antenna and mast on the ground. It came down by the gravity method. (Photo by Linda)

The bonus to this work at the top of the tower was a commanding view of the surrounding countryside, which was mostly trees in every direction.  I even saw two towers far to the north and was kept company by a soaring vulture just to the NNE.  I was also able to determine that the tops of the large white pine trees behind the east end of our house are about 10 feet higher than the top of our tower, putting their overall height at about 55 feet as their bases are lower than the base of the tower.  We plan to put the 70 foot tower at a spot that is surrounded by these trees on three sides (W, S, and E) so the top of the tower, and any antennas mounted there, will be well above the tree tops.  That is especially important as we plan to eventually put an HF beam antenna up there on a mast attached to a rotator and it will need to be able to rotate freely for 360 degrees.

The final antenna was the hardest.  The Antennas Direct DB8e OTA UHF/digital TV antenna was very large and heavy by comparison to the other two.  In this case ‘heavy’ meant a few pounds.  It is actually two UHF antennas mounted at the end of a dual support arm structure.  The support arm mounts to a vertical pole, such as a tower leg, at its midpoint and there is a combiner box located there as part of the mount.  A short length of RG-59 (75 ohm) coax connects each antenna to the combiner box and the main coax connects there as well.

How tall the tower appears (and feels) depends on where you are standing. (Photo by Linda)

How tall the tower appears (and feels) depends on where you are standing.  Pulley and haul rope in the upper right.  Lots of coaxial cables to be dressed (secured) on the way down.  (Photo by Linda)

RG-59 is a different kind of coaxial cable from the LMR-400 used for the first two antennas.  LMR-400 has a 50 ohm characteristic impedance and is used for receiving and transmitting RF energy with considerable power if needed.  RG-59 is much smaller in diameter, more flexible, has a 75 ohm characteristic impedance, and uses F-connectors that are the standard for OTA TV, video, and satellite cables.  But I have gotten ahead of myself.  I had to come down a few feet on the tower to install the TV antenna but before doing that I had to start securing the transmission lines to the tower legs with cable ties.

Mike rigged up the haul rope in a ‘Y’ to lift the antenna from its center of gravity while actually attaching the rope to its ends.  That allowed the haul rope to both support the weight of the antenna and keep it oriented correctly while I positioned and clamped it to the southwest tower leg with the dual support arms pointing in an east-west direction.  Because of where I had the pulley mounted, and the length of the ‘Y’ in the support rope, I had to mount the antenna a few feet lower on the tower.  Fortunately the slightly lower height was not going to affect its performance.

Like the ham radio antenna, the OTA TV antenna mounted to the tower leg at two points.  The upper assembly was a U-bolt with a retaining bracket on the back side.  The lower assembly was a pair of straight bolts that went through the combiner box past the tower leg and had a retaining bracket on the back side.  The antenna came with wing nuts instead of washers and regular nuts, which helped a little, but I really needed three hands to get the antenna into position and tighten the mounting brackets.

Mike ties off the DB8e OTA TV antenna with an inverted "Y" so it will haul up in the proper orientation. (Photo by Linda)

Mike ties off the DB8e OTA TV antenna with an inverted “Y” so it will haul up in the proper orientation. (Photo by Linda)

Once I had the antenna sufficiently attached to the tower I was able to position the support arm close to the southeast facing side of the tower.  I then pointed the antenna on the east end of the arm ESE towards the Detroit area TV towers and tightened the two nuts on the mounting studs.  (The horizontal dual support arms are about 3 feet long so I was able to reach through the tower to get to the mounting studs and nuts.) I left the antenna on the west end of the support beam loose and turned it out of my way so I could complete other tasks.

Mike attached the end of the main RG-59 coax to the haul rope, put the amplifier and a 2-foot length of RG-59 coax in the bucket along with lots of zip ties, and pulled them up to me.  The amplifier is about 3″ wide by 2″ high and 1.5″ thick including the concave plastic backplate.  The backplate accepts two zip ties for mounting to a pole.  I positioned the amplifier about 8 inches below the antenna combiner box and cinched up the two zip ties.  I then connected the short coax to the combiner box output and put the combiner back it its protective, weather-gasketed plastic box.  I connected the other end of the short coax to the amplifier input and wrapped the connection with coax seal weatherproofing tape.

Installing the DB8e OTA TV antenna required three hands. Note that I am installing it at the highest point possible when suspended from the pulley with the haul rope in an inverted "Y" attachment. (Photo by Linda)

Installing the DB8e OTA TV antenna required three hands. Note that I am installing it at the highest point possible when it is suspended from the pulley with the haul rope in an inverted “Y” attachment. The yellow waist strap allowed me to lean back and work while the two red security straps would catch me if something broke. (Photo by Linda)

I attached the main RG-59 coax to the output of the amplifier, which is also the DC power input, and wrapped the connection in coax weather seal tape.  I then dressed the cable and secured it to the tower leg.  I aimed the antenna on the west end of the support arm WNW towards the East Lansing TV towers and tightened the nuts to lock it in position.

At this point I was finally done working on the antennas but had three coaxial transmission line running down the outside of the tower, one by each leg.  As I descended the tower, reversing the protocol I used going up, I secured all three cables every few feet.  I finally had my feet back on the roof at 2:20 PM, almost exactly 2 hours and 30 minutes from when I started climbing.  Projects usually take me twice as long as I think they will but this was about half as long as I thought it would take, so we were all pleased that the work had gone smoothly and relatively quickly.  My main objective was to get the old TV antenna down and the three antennas up but my secondary objective was to only climb and descend the tower once.  Mission accomplished, at least for now.

By now we were all hungry and thirsty so Linda made chickpea salad sandwiches and set out fresh sweet peppers, sliced apples, baby carrots, and cold water.  After a suitable lunch break we returned to the next phase of the work which was routing the coax cables into the cable entry box (CEB) and making the connections.

We started with the RG-59 coax from the OTA TV antenna.  I coiled the extra cable and hung it on the tower (with zip ties, of course), routed it into the CEB and connected it to the power inserter / lightning arrestor.  We purchased this cable from a Radio Shack store in Florida two winters ago to hook up our bus to the RV resort cable TV system.  Besides the coax it had a separate ground wire.  The amplifier and the power inserter both had connections for a separate ground wire so I connected it on both ends.

Routing coaxial cable into the cable entry box from the tower and the basement and making the connections. (Photo by Linda)

Routing coaxial cable into the cable entry box from the tower and the basement and making the connections. (Photo by Linda)

We had already routed a 75 ohm video cable from our bedroom TV to the sump pump room in the basement.  I selected a suitable length of this same type of cable from our existing inventory, connected it to the other side of the power inserter, and routed it through the back of the CEB into the sump pump room where Linda guided it.  Conveniently, I had a double-ended F-female barrel connector designed to connect together two cables with F-male connectors.  I plugged in the AC power adapter for the power inserter, which was already in the sump pump room, and we went upstairs to see if we were receiving any TV stations.

We set the ‘Source’ on the TV to ‘Antenna’ and did an ‘Auto Scan’ for digital channels only.  There are very few analog TV signals still in use and the ones that are reside in the old VHF TV spectrum which our new antenna cannot even receive.  The scan found 58 signals, which obviously included the sub-channels.  Besides the main Detroit stations and the East Lansing PBS station we got other Lansing area stations and even a station from Flint.  The nice thing about digital TV is that if you get a picture at all it is very good.

There is a large TV tower at I-96 and US-127 on the southeast corner of Lansing so we were probably picking it up.  There are several TV towers SSW of Lansing about 35 miles that serve Battle Creek and may serve Lansing and Kalamazoo.  They are 50+ miles from us and I did not have the west antenna pointed in exactly that direction but it may have been close enough to pick them up.  Flint is at least 35 miles away straight north off the sides of both antennas so theoretically we should not have received any stations from that direction.  We will have to check the AntennaPoint.com website and confirm by station identifier what stations we are actually receiving.

Feeling good about our success so far we routed the coax for the cellular booster across one of the support arms that brace the tower to the house just under the east soffit.  We dropped it down next to the wall and brought it into the bottom of the CEB, replacing the hole plug with a rubber grommet.  Routing it this way kept it out of the way of future foot traffic, or lawn and garden work, in the space around/between the tower and the CEB.  I connected the cable to the lightning arrestor and coaxed it unto position inside the CEB.  LMR-400 is stiff and bending it sharply will damage it.

I connected one end of the 15-foot LMR-400 cable to the other side of the antenna arrestor and routed it into the sump pump room where Linda guided it into position.  I secured it to the ceiling, brought it down the opposite wall, put a large 180 degree bend in it, and attached it to the connector on the bottom of the cellular booster.  I turned it on and watched the lights blink for a while.  All three of us then started checking signal strength throughout both floors of the house.  All five of the ‘Alert’ lights went from blinking yellow, which means the unit is adjusting the gain on that band, to solid yellow, which is not described in the manual.  Since we had not yet registered the device with Verizon Wireless I turned off the booster.

Back out at the CEB I removed one of the hole plugs directly below the input of the Morgan VHF lightning arrestor.  We routed the coax for the 2m/440 ham antenna across the tower brace, down the wall, and around through the bottom of the box where I attached it to the lightning arrestor input.  I had an old piece of 50 ohm coax with an N-male connector on one end and a PL-259 (male) connector on the other end.  I attached the N-connector to the output of the VHF lightning arrestor and fed the other end through one of the 2″ conduits into the sump pump room where Linda routed it out into the ham shack.

We set our “Go Box” on the desk, plugged the PL-259 into the SO-239 socket on the back of the case, plugged it in to AC power, turned on the power supply, and turned on the radio.  The radio, an Icom IC-7000, came up tuned to the South Lyon (K8VJ) repeater.  I transmitted and successfully triggered the repeater, which is currently at a secondary site about 20 miles from our tower.  Mike went out to his car and used his mobile radio to verify that we could transmit to and receive from the repeater.  I had a lot of background static (white noise) so Mike switched modes and transmitted directly to our antenna.  The signal was full scale and full quieting.  I have a ground lug in the Go Box but did not have it connected.  I vaguely recalled that I had to ground the box at the previous house to eliminate a noise issue.  (The radio and power supply are grounded to the box.)

I switched the radio to UHF and it was set for the Novi repeater.  I listened but did not hear anyone transmitting so I transmitted, giving my call sign and a brief message, and then listened.  I did not get a reply even though Mike was also monitoring the Novi repeater so I switched back to the South Lyon repeater.  Mike indicated that I had, indeed, triggered the repeater and that a couple of other hams acknowledged hearing me in addition to him.  It thus appeared that I did not have something set up correctly on the receive side of the radio for the Novi repeater but the system (radio, cables, arrestor, antenna) was clearly working.

That was enough work for one day so we gathered up all of the tools and unused materials and put them away.  We offered to take Mike to dinner as a ‘Thank You’ for his assistance.  It was more than helpful to have someone on the ground who was familiar with tower operations.  We considered several dining options but opted for Olga’s in Brighton.  Linda and I had small salads, sans the Feta cheese, veggie Olga’s that were excellent, and curly fries without Tabasco sauce for the ketchup.  Warning:  As inconceivable as it may sound, Olga’s does not have any kind of hot sauce in its restaurants.  Mike had a dish with chicken in that he said was very good.

Mike headed home from the restaurant as did we.  We were tired but very pleased with what we had accomplished in the course of the day.  We celebrated our accomplishments by watching several programs on Detroit PBS, something we have not been able to do for more than two years.

 

2015/06/23 (T) Grounded

Leave a reply

As I wrote in yesterday’s post we did not turn off the lights last night until almost 1 AM because we were keeping a close eye on the weather moving across the lower portion of Michigan’s Lower Peninsula.  Although strong to severe storms were still forecast from 1 AM to 5 AM they either did materialize at our exact location or we slept through them.  We had the house closed up and the air-conditioning on, so that cut down the sound level of outside noises.

A cold front had pushed through by sun up and we woke to a cool morning with blue skies and noticeably lower humidity.  We did not have any trees, or even big limbs, come down and there was no damage to our brand new roof.  The forecast yesterday was threatening enough, however, that in the morning we took the potted plants, and as much of our outside lawn furniture as we could find room for, inside including our sun umbrella and trash cans.  I planned to be gone most of the day, and Linda was leaving mid-afternoon to go to dinner and a movie with Diane Rauch, so our first chore was to put all the lawn furniture, plants, and other outdoor stuff back outdoors.

This week is mostly being devoted to ham radio with the ARRL Field Day as the crowning event this weekend.  My specific focus for most of the week, however, has been the “communications tower” adjacent to the east wall of our house.  As described in previous posts we installed a cable entry box (CEB), mounted the cellular booster in the basement, mounted the inside cellular antenna, and ran coax cables.  The antennas will (hopefully) be mounted on the existing 40 foot tower tomorrow, cabled into the CEB, and cables run from there to devices inside the house.  With any luck by the end of the day tomorrow we will have decent cellular service inside the whole house, the ability to watch OTA TV programs on two different TV sets, and finally be able to connect one of our radios in the ham shack to an antenna.  Today, however, was planned to mostly address other things.

I had an appointment with our dentist at 10:20 this morning and left at 9 AM.  I planned to stop at Chuck’s bus garage and check that the key he lent me worked, but I needed gas for my car.  I did not have time for both and did not really have a choice; I would have to check the key some other time.  I ordered two cables yesterday from Scott (AC8IL) at Adams Electronics.  Later in the evening I was unsure if I had specified the connectors correctly so I called and left a message.  I called again this morning to make sure the message got through.  It did, and my original connector specifications were correct.

I arrived at the dentist’s office about 10 minutes before my appointment time.  I called Rick Short at Isringhausen USA to make sure he was going to be in before I drove two hours to Galesburg, Michigan after my dentist appointment.  I got his voice mail a left a message.  “ISRI” makes very high tech air suspension driver’s seats that are used as original equipment in motorcoaches, semi-tractors, heavy equipment, and locomotives.  I would really like one for our bus, but it is not proving easy to get.

Dr. Steve and his assistant, Leslie, made molds of my upper and lower teeth and a bite impression.  The molds will be used to make a mouth guard that I can wear while I sleep.  Dr. Steve has a strong suspicion that I am clenching my teeth and the mouth guard will reduce or eliminate the irritation it causes.  I will have to ask if I can wear it during the day too as I am occasionally aware of clenching my teeth while I awake.

I had not heard back from Rick by the end of my appointment so I called the main number at ISRI and talked to the receptionist.  It turned out that Rick was not in today and she transferred me to Jeff Woodworth.  Jeff was willing to meet with me but thought it would be a better use of my time to wait until Rick was available.  My next opportunity to drive to Galesburg will be Thursday and I will likely go as the ISRI seat is holding up our ordering of Flexsteel seats through Coach Supply Direct.

I stopped for coffee and then re-routed for Chuck’s bus garage in Novi.  The key to the garage worked perfectly.  I called Linda to let her know about the change in plans and headed for home.  There is too much to do at the moment to waste much time so I installed the #4 AWG bare copper ground wire I bought yesterday at Lowe’s.  I mounted an offset copper wire lug using the center support stud for the copper back plane in the CEB.  I replaced one of the plastic hole plugs with a rubber plug with a small hole in the center.  The hole I chose in the bottom of the CEB allowed the ground wire to come straight up into the lug.

Another view of the cable entry box on the east end of the house by the 40-foot tower.

Another view of the cable entry box on the east end of the house by the 40-foot tower showing the bare copper ground wire that runs to the ground rod and then to one of the tower legs.

Outside the CEB I routed the ground wire around to the existing ground rod and secured it using the new clamp I bought yesterday.  There was an old ground wire connected from a clamp on the tower to the ground rod.  I removed that wire along with some coax and control wires that I had clipped when we removed the old satellite dish.  I then attached the new ground wire to the clamp on the tower.  While we were at it Linda trimmed back a small bush that was growing between the tower legs and I pulled leaves, grass and other stuff out from around the Day Lilies that we transplanted last year around the tower base.

With the CEB grounded we looked at how we might get a video cable up to the TV/monitor in our bedroom.  The wall where the TV is mounted has a hot water baseboard radiator that comes almost to the trim on the door wall.  That end of the radiator has a copper pipe that goes through the floor into the basement and it was easy to locate the pipe in the basement.  I determined that there was enough space behind the pipe to safely drill a hole but I had to drill it from the top side at an angle.  A 5/8″ wood boring drill bit created a hole just big enough for the molded F-connector on the end of the cable to pass through.

We fed the video coax cable above the suspended ceiling in the ham shack area to the location of the hole.  I then fed the cable up from the basement as Linda pulled it up into the bedroom.  We adjusted the amount of cable in the bedroom to allow the wall mounted TV set to move through its entire range of motion.  The other end of the cable was then routed into the sump pump room.

By the time we finished pulling this cable it was 3:30 PM and time for Linda to leave to pick up Diane.  They were headed to Royal Oak for dinner and a movie as the movie they wanted to see was only showing at the Royal Oak Main Theater.

While I was out during the morning Lynch Carpet had called to let us know our Armstrong vinyl tile was available for pickup so after Linda left I closed up the house and went to get it.  The 12 boxes of tiles, container of vinyl adhesive, and container of vinyl grout were all neatly arranged on a small pallet and tightly wrapped in shipping plastic.  Rather than break this down and load each thing individually they used a fork lift to set the pallet in the back of my Honda Element.  The rear suspension settled at least two inches when they transferred the full weight of the pallet to the floor of my car.

When I got back to the house I backed the car up to the garage.  I cut the shipping plastic loose and unloaded the tubs and boxes of tiles.  I put the pallet on the garage floor and then neatly stacked the boxes of tiles on it to keep them off the floor.  Each box contained 14 tiles measuring 16″ by 16″ for a total area of 24.89 square feet.  The Armstrong Alterna tiles are a “luxury vinyl” product, and are about 1/8″ thick.  Even so, the boxes were heavier than I expected so I decided to weigh one.  It tipped the scale at just under 42 pounds.  That meant the entire pallet weighed close to 500 pounds, and, ignoring the weight of the cardboard box, that is about 3 pounds per tile.

When I drew out the design I determined that I would need 158 tiles, some of which would be partial.  Figuring conservatively at 150 full tiles equivalent, and ignoring the weight of the underlayment, adhesive, and grout, the floor tiles will weigh about 450 pounds.  I have no idea what the carpet and ceramic tile that I have removed weighed but the tiles were heavy.  I also have no idea what the furniture weighed that we have removed but also have no idea what the new furniture will weigh.  The intent was that the new floor and furniture would weigh less than old stuff but we will see.

I traded phone calls with my dad and we finally got to talk for a half hour starting at 4:30 PM.  He turned 90 this past Sunday.  Mike Fearer from Bid-Rite Concrete called at 6 PM and arrived about 10 minutes later to discuss the foundation for our 70 foot ham radio tower.  I had printed off a page from the Universal Tower website showing their tower base.  I also downloaded and printed their base and tower installation instructions.  I had a set of these to give to Mike so he would have some idea of what the project is about.  We looked at the proposed location for the tower and access for his dump cart.  We also talked about the base, a rebar cage, a form around the top of the hole to allow the concrete to be slightly above ground, and a jig to make sure the base is level and the tower is plumb.

He said he was interested in the job and would work with me and Phil Jarrell (the excavator) to get it done.  Rather than bid the job he would just do it for time and materials.  He also said the current price of concrete was about $100 per cubic yard.  We will need about six (6) cubic yards to fill the required 5′ x 5′ x 6′ (deep) hole.  He thought he might be available the middle of next week but I don’t think I could have everything pulled together that quickly.

After Mike left I went to Lowe’s and picked up five 40 pound bags of topsoil, a 1-in/2-out signal splitter (rated for 5 MHz to 2.4 GHz), and a plastic snap cover channel for hiding the video cable we ran up into the bedroom from the basement for the TV set.  I then went to the Meijer’s supermarket just across Grand River Avenue for soy creamer but they did not have what I was looking for.  As long as I was there I had a salad for dinner at the in-store Subway.

While I was sitting there I called Mike Sharpe (W8XH) to confirm that he was available tomorrow to help with the antenna installations on our 40 foot tower.  I mentioned that the only thing I lacked was a standoff with a pulley at the end of it for hoisting stuff up to me.  He suggested that something like that was essential and I agreed, so I headed back to Lowe’s to see what I could figure out.  What I ended up with was a three foot long 7/16-14 threaded rod, a pulley that had a closed eyelet on top (and was big enough for the 3/8ths rope I bought), some 7/16ths washers, and some 7/16-14 nuts.

When I got back to the house I unloaded the topsoil near the part of the east yard that needs to be filled in, took the other stuff inside, and then assembled the threaded rod pulley system.  I secured the pulley on one end of the rod using two of the nuts, one on either side of the eyelet.  I threaded a nut onto the other end, put on two washers, two nuts, two more washers, and another nut.  I ran the first two nuts, with two washers between them, part way down the rod.  I left the second pair of nuts, with washers between them, near the end of the rod.

I took the assembly out to the tower and adjusted the position and spacing of the two pairs of nuts and washers so they would bracket two of the horizontal tower members.  In use I will secure the rod to the tower at each pair of nuts/washers using plastic cable ties.  This arrangement will put the pulley at least 18″ from the tower which should be far enough out that we can hoist the DB8e OTA TV antenna to the top of the tower without it banging into the tower or hanging up on something.  This antenna is the largest thing we need to hoist up. The old TV antenna is considerably larger and heavier, but it is coming down via gravity.

There was a message on our answering machine from Linda’s sister, Sr. Marilyn, who lives in St. Louis.  She was listening to the news earlier today about the storms that went through our part of Michigan and wanted to make sure we were all OK.  By the time we finished talking it was dark and I was done working for the day.  Linda called shortly thereafter to let me know she was on her way home and I mentioned the call with Marilyn.

I finally opened the box with the vertical omnidirectional outside antenna for the cellular booster system and discovered that I should have opened it sooner.  The mounting bracket was designed to be mounted to a vertical surface, such as the side of a house, not a tube, such as a tower leg.  I did not want to postpone tomorrow’s tower work so I will have to get up early and figure out a way to adapt the existing bracket so I can mount the antenna to the top of the tower.

My initial thought was that an aluminum U-channel of the correct size might solve the problem very nicely.  I could drill two holes in the bottom of the “U” to match the two holes in the bracket.  I could then drill three pairs of holes through the sides of the channel.  The antenna would be bolted to the bottom of the channel.  With the open part of the channel held against a vertical tube I could secure it with three long plastic cable (zip) ties.  Conceptually it should work and be easy to fabricate, but will take time which I won’t have a lot of in the morning.  We have to get the two coax cables from Scotty (AC8IL), drop off my car at Brighton Honda for its 100,000 mile service, and be back in time to have the mount fabricated and all of the antennas and tools ready to go by 10:30 AM when Mike shows up.

Linda got home at 9:45 PM, earlier than she thought she would when she left.  She and Diane ate at Luigi’s and had a very nice meal.  They also enjoyed the movie.  We had a big day on tap for tomorrow and we asleep by 10:30 PM.

 

2015/06/22 (M) Cable Me This

Leave a reply

We turned the air-conditioning off last night and enjoyed the fresh air, pleasant temperature, and lower humidity.  The overnight low was 58 which made for good sleeping.  We awoke to blue skies and what we thought would be a picture perfect Michigan summer day until Linda checked the morning news (iPad).  There was a story about a storm that moved through the upper plains yesterday and had a bead on Michigan for later today and this evening.  What had been a 10% chance of rain for today had been replaced by a forecast for strong-to-severe thunderstorms with the possibility of strong winds, large hail, and tornadoes.  Ahhhh, summer in Michigan.

Not ones to sit around and wait for the apocalypse we did what any sensible couple would do, I made coffee while Linda reheated the last of the Baked French Toast from yesterday’s brunch.  We had breakfast and then sat on the deck enjoying our coffee and contemplating the end of the world, or at least the possible destruction of our brand new roof.  But it’s insured, so “no worries, maan” as they say in Jamaica.  More coffee please.

We have a whole house generator that runs on natural gas so as long as a storm doesn’t damage it we can survive for a very long time without electric utility power.  Losing our AT&T Internet connection, however, would be a genuine hardship as that would require us to use our Verizon Mi-Fi (without the benefit of the new Fusion5s cellular booster which I plan to install on Wednesday) or go to Panera, McDonalds, or one of the libraries to get online.

Keith showed up around 10 AM to cut the grass.  We were hoping he would make it as we have not had too much rain this past week and the last few days in particular have been dry.  I think this is the first time this season he has been able to cut our grass without it being wet.  It looked nice when he was done.

I got a call from Phil Jarrell.  He had been successful in reaching Mike Fearer of Bid Rite Concrete on Mike’s cell phone.  Based on Phil’s description Mike was interested in looking at our tower foundation project and was expecting me to call so I did, using my cell phone, and this time I was able to reach him.  It turned out that the information about his business on the Internet is out of date.  He is no longer in Whitmore Lake but now operates from near M-59 and Latson Road, not far from us.  We agreed that he would stop by tomorrow at the end of the work day to look at our project.

I did not want to do a lot of heavy work today, as I was still a bit tired and sore, but I needed to mount two lightning arrestors in the cable entry box and mount the cellular booster in the sump pump room so I could figure out what coax cable lengths I needed and go get them from Scott Adams (AC8IL) at Adams Electronics in Wixom.  But first I called Mike (W8XH) to let him know I was planning on Wednesday for the tower work, assuming he was still available and the tower was still standing.

Cable entry box showing copper ground plane with Morgan lightning arrestors (lower left), control line arrestor (center top), and cellular and OTA TV arrestors (center).

Cable entry box showing copper ground plane with Morgan lightning arrestors (lower left), control line arrestor (center top), and cellular and OTA TV arrestors (center).

I determined that I needed two coaxial cables and ordered them from Scott by phone rather than take the time today to drive to his place of business.  They will both be LMR-400 with N-connectors on both ends.  One will be 50 feet long, for our 2m/70cm Diamond X50-N VHF/UHF base station antenna, and the other will be 15 feet long, to get from the cellular booster lightning arrestor in the cable entry box to the repeater (amplifier) in the sump pump room.  I will pick them up early Wednesday morning and install them.

One of the lightning arrestors was for the SureCall Fusion5s cellular booster system.  It has N-connectors on both ends, one of which is intended for bulkhead mounting.  It came with an angle bracket that fit over the bulkhead end and I used that to mount it.  I used the 2′ length of LMR-400 that came with the booster installation kit to position the lightning arrestor so the cable from the repeater could exit one of the 2″ conduits and bend around and connect to it.  LMR-400 is a low loss, 50 ohm impedance, coaxial cable that can handle high RF transmit power.  The cellular booster only has a 1 Watt transmitter but is operating at frequencies where energy losses in coax cables become significant.  To do what it does LMR-400 is just under 1/2″ in diameter.  It is fairly stiff and does not make sharp bends so cable runs and connections have to be carefully planned.

The other lightning arrestor was for the Antennas Direct DB8e OTA TV antenna and serves a dual purpose as the power insertion device for the tower mounted amplifier.  The coax cable for OTA TV signals is typically 75 ohm impedance RG-6 with F-connectors.  It is half the diameter of LMR-400 and much more flexible.  It is also typically used to receive low power signals and convey them in one direction; from the antenna to the TV.  Because we are 25 miles from the nearest TV tower and some of the towers are 50+ miles away, I ordered a signal amplifier to go with the antenna.

Ideally you want to amplify an OTA TV signal as soon as it comes out of the antenna and this amplifier does just that.  It will mount on the same tower leg as the antenna about two feet below the antenna feed point.  However, being an active electronic device it needs electrical power to operate.  There are two basic ways that could be done.

One way would be to have power wires, such as +5 VDC and DC Ground that are separate from the coaxial cable that carries the radio frequency (RF) energy.  The two OTA TV antennas on our bus are set up this way with three wires to supply power and control the enclosed rotor.

The other way is to provide DC power through the coaxial cable itself, which is how this amplifier is set up.  The nice thing about this arrangement is that the amplifier only has two connections and they are both coax connectors that can be weather sealed.  To get the DC power into the coax cable, however, requires a special device called a power inserter.  The power inserter, in turn, requires the coax to be split into two segments so there end up being four connections instead of two.  The power inserter for this amplifier very conveniently acts as a lightning arrestor as well, which is why I mounted it to the copper back plane in the cable entrance box.

By boosting what I presume will be weak signals from distant towers the amplified signal should be strong enough to survive the trip through the coax cable to the power inserter, from there to a 1-in/2-out signal splitter, and then through additional lengths of coax to the two TV sets.

After getting the two lightning arrestors mounted in the cable entry box I took a break for lunch and then went to Lowe’s for some supplies.  When I got back home I turned my attention to mounting the SureCall Fusion5s cellular booster (repeater amplifier) in the sump pump room.  The sump pump is in the northeast corner of the basement, which is also the northeast corner of our ham shack and office.  (The ham shack occupies the north wall and my desks occupy the east wall.  Most of the rest of the room is storage.)

I gutted and rebuilt this space, with the help of long-time friend John Rauch, before we moved in and created the large closet (small room) around the sump with insulated walls to contain sounds.  I installed an electrical sub-panel in this room to provide power to the office and ham shack desks and to an RV outlet by the pull-through driveway.  I fed the power for the RV outlet through the bond on the east wall just above the concrete block foundation and ran it underground to the far side of the driveway.  It was my intention from the beginning to mount a cable entrance box next to the power feed and have all of the coax cables and control wires for outside devices enter the sump pump room in the same manner as the power.

The ham shack/office walls are finished with T-111 exterior plywood with 4″ groove spacing and I finished the interior of the closet the same way as I knew I would eventually want to mount things to the walls.  I mounted the SureCall Fusion5s booster on the west wall of the closet about a foot inside the door and just below my eye level so I could see all of the connectors, switches, and indicator lights on the top and front of the unit.  It had four mounting tabs, two top and two bottom, that attached easily to the wall with short wood screws.

There is a duplex AC electrical outlet on that wall and one on the opposite (east) wall.  The power supplies for the cellular booster and OTA TV antennas will plug in to these along with the sump pump and the charger/controller for the battery powered backup sump pump.  One of the things I bought at Lowe’s were two outlet expanders which I installed in these two duplex outlets.  I also bought a switch with a pilot light to replace a single pole Decora switch that will eventually control the light in the closet.  I installed the switch but did not complete the wiring as I have to tie it in to the light fixture which requires me to cut the power to that circuit.   I would also like to replace the bare bulb fixture while I am at it but have not yet purchased a replacement.

Although it was late afternoon I decided to install the inside antenna for the cellular booster system and run the coaxial cable that connects it to the booster.  The antenna is designed to mount to a flat ceiling and provide a hemispherical coverage area below the plane of the ceiling.  I had previously figured out that if I mounted this antenna in the main floor hallway near the midpoint of the house I could connect it to the cellular amplifier using a 50 foot length of coax cable that came with the system.

The desired mounting location was opposite the door to the hall closet and the access to the attic is through the ceiling of that closet, so that was very convenient.  We emptied the closet, removed the clothes rod, and setup our six foot step ladder.  I removed the piece of foam insulation we currently use to seal the attic access opening and climbed up, flashlight in hand to check out what was on the other side of the ceiling.

Our desired location for the antenna was free of problems on the back side so I drilled a 3/4″ hole for the mounting stud and used a piece of rebar to poke a hole through the insulation for the coax cable that came out of the stud.  Linda fed the coax and stud through the hole and I put the retaining nut on the stud from the attic side of the ceiling.  The antenna is shaped like a coffee filter, is about six inches in diameter at the ceiling, and tapers down to about four inches in diameter about four inches from the ceiling.  The housing is white plastic and blends in well with the ceiling paint.

About four feet from where we installed the antenna is a chase that runs from the attic to the furnace room in the basement.  It appears that once upon a time something having to do with the furnace ran through this chase, such as the combustion air intake.  The combustion air is now drawn through the back wall under the deck and the exhaust goes out through the east wall of the basement via a double wall stainless steel flue pipe.  The chase is no longer used for furnace or other utilities although there are electrical cables to switches mounted in the bathroom walls and it still contained a piece of 4″ plastic pipe.

I positioned myself near the chase and guided one end of a 50 foot length of LMR-400 coax down through the pipe and through the hole into the furnace room while Linda held the roll of coax near the top of the ladder and unrolled it.  At one point the coax bunched up and Linda had to go to the furnace room and untangle it.  At another point the 4″ plastic pipe slipped through the bottom hole into the furnace room which caught me by surprise.  Once the cable was mostly fed through I routed it to the location of the antenna, connected it to the pigtail coax from the antenna, wrapped the connection in weather seal tape to keep moisture out, and secured it with a cable tie.

With the antenna installed Linda started preparing dinner while I dealt with the 37 feet of coax in the furnace room.  The furnace room does not have a finished ceiling so I had access to the areas above the suspended ceilings in all of the adjacent rooms.  In particular I was able to feed the free end of the coax above the ceiling in the office and into the sump pump room.  I secured the cable with plastic cable ties at two points in the furnace room to keep it away from the flue and various hot water pipes.  I had about 8 extra feet of cable so I made a large coil with two loops such that the free end came off the loop straight down into the connector on top of the booster.  I hung the coil on the wall above and to the right of the booster making for a very neat installation.

I took a shower to try and get rid of some of the fiberglass itch while Linda finished the dish she was making for dinner.  It was a complex Indian style dish with Basmati rice, garbanzo beans, Swiss chard, onions, and shallots, seasoned with salt, black pepper, cayenne pepper, cumin seeds, garam masala, fresh lemon (zest and juice), and fresh dill that Linda grew herself.  The house was filled with the aromas of all these ingredients for a couple of hours as they were prepared and combined into the final dish.  It tasted as good as it smelled with many flavor layers.

Our beautiful blue sky gave way to high, thin clouds through the morning and then to lower, thicker clouds during the early afternoon.  By 2 PM the clouds to the west were dark as I drove to Lowe’s in Howell and the first, heavy rains came as I got to the parking lot.  I waited a few minutes and they stopped so I got into the store without getting wet.  I had the same good fortune on my way back to the car.  The sustained rains came later in the evening along with a tornado watch.  We went to bed before 10 AM but did not go to sleep.  It took me a long time to write this post and we kept a watchful eye on the weather radar.  Although thunderstorms were forecast as a certainty from 1 to 5 AM with the possibility that they might be severe, we finally turned the lights out around 12:45 AM and tried to get some sleep.

 

2015/06/18 (R) Chiseled Bikinis

Leave a reply

The light rain that started late yesterday afternoon continued off-and-on through the overnight hours.  We awoke to heavily overcast skies but a forecast that called for dry conditions until the early afternoon.  We were up at 7:15 AM and had our usual granola breakfast.  I took some more Ibuprofen in advance of working in the bus.  We were just getting ready to have our morning coffee when I noticed several cars in the driveway.  It was 7:45 AM and the roofers were arriving.  Pat Davidson was among them so I went outside to chat briefly with him.

We had our morning coffee and then got to work, Linda at her desk and me in the bus. I spent another two hours using the Makita 11 pound power chisel.  By 11 AM I had removed as much material from the floor as I felt was worth the effort.  Linda brought the camera out and took a few photographs of me at work after which I packed up the equipment, closed up the bus, and went to Home Depot in Howell to return it to their rental department.

I stopped at Lowe’s on the way home and ordered the new Frigidaire refrigerator for the bus, an FFHT1621QB (16.3 cu. ft., top freezer, black, no ice maker or water).  I scheduled delivery for Friday July 3rd to Chuck’s shop in Novi.  I will arrange with Chuck to take the bus their sometime after that when he is available to operate his fork lift and I can get Brendan or some friends to give us a hand.

Me using the Makita 11 lb power chisel to remove thinset and mastic from the floor of our H3-40. (Photo by Linda)

Me using the Makita 11 lb power chisel to remove thinset and mastic from the floor of our H3-40. (Photo by Linda)

Work continued on the roof through the morning and then the crew tarped off the roof and left in a few of their vehicles for a long lunch.  As forecast it started to sprinkle around 2 PM as they returned from their lunch break.  It never rained hard and they kept on working but always with the tarps at the ready in case they were suddenly needed.  One of the guys finished installing our two Velux Sun Tunnel skylights which required a tall step ladder in our living room.  They looked very nice when he was done.

I had a chat with Jarel Beatty in Logansport, Indiana about the custom desk he is going to build for the bus.  I sent him a follow-up e-mail describing the pullout pantry we also need him to build.  I then spent an hour working on drawings before I had to quit and change clothes.

Kate had secured tickets through her cousin, Michaela, for this evening’s performance of The Bikinis at the Meadow Brooke Theatre at Oakland University in Rochester Hills.  Kate suggested O’Conner’s Public House (Irish Pub) in Rochester for dinner.  The roofers had been working in the living room installing the Velux Sun Tunnel skylights but were done by 3:45 PM.  That allowed us to get cleaned up, dressed for the theatre, and out the door at 4:30 PM even though the roofers were still working up on the roof.

We got to the pub at 6 PM.  Kate got there shortly before us and had ordered a soft pretzel appetizer before the happy hour prices expired at 6 PM.  Conveniently there were three large sticks so we each got one.  Kate got the cheesy dipping sauce and we split the spicy horseradish mustard, which really had a kick to it.  Linda and Kate each had a Smithwicks ale and I had a pineapple ale.  To paraphrase “the world’s most interesting man”:  I don’t always drink beer, but when I do, I prefer a fruit beer.  Not as mysterious as Dos Equis, or as authentic as Guinness, but it’s what I like.  Kate had a regular (beef) burger and we both had black bean burgers on soft pretzel buns with fresh hand-cut French fries.  The burgers and fries were both really good and the pretzel buns, which had been toasted on a grill, did not get soggy.

The musical was a lot of fun with a wonderful performance by the cast of four women.  All four of them were on stage singing and dancing with a lot of energy for most of the performance.  Their singing was excellent, each voice having its own unique quality but blending well, and they carried 4-part harmonies in tune with one another and the small 4-pieces band.  Two of them, Bambi Jones and Jeanne Tinker, were also in the Meshuggah Nuns musical we saw a month or so ago at the Meadow Brooke Theatre.

The Bikinis is the last production that Kate’s cousin Michaela will work on at the MBT.  The production run ends on Sunday and one week later she leaves for a summer stock gig in New England.  Meadow Brooke Theatre is a wonderful venue but not convenient to where we live, even less convenient to where Kate works, and very inconvenient to where she lives.  All of which is to say, I doubt that the three of us will be going there very often now that Michaela is moving on.  That is too bad in a way as we have all enjoyed the shows we have seen.  The fact that Michaela, as a cast/crew member, was able to get us tickets did not hurt.

Michaela met us in the lobby where Kate gave her a nice assortment of flowers.  She then gave us a behind the scenes tour of the wardrobe area where she has spent the past year working on costuming.  We walked out to our cars and by the time we all drove off it was 11 PM.  Even with light traffic it took us almost an hour to get home but we arrived while it was still Thursday, albeit just barely.

 

2015/05/20 (W) Duraclean

Leave a reply

Today was carpet cleaning day.  Linda had been picking up the house for the last week getting ready but we still had a lot of last minute stuff to move, including the cats.  We put them in the library along with their food, water, and litter tray.  We also moved their cat “tree” out there.  They were confused and unhappy about the arrangement but we figured it would be less stressful for them than constantly trying to find new places to hide as Jack moved about the house with his big, noisy carpet cleaning machine.

Jack Hoskins runs a one-man carpet and upholstery cleaning business named Duraclean.  Located in Farmington Hills near our previous house, Jack took care of our cleaning needs for the last years we were there.  When we bought the house in Oceola Township we had him clean all of carpets after the painters were done but before we moved anything into the house.  We did not have him clean the carpets in 2014 but had him out today to do all of them, including my office / ham shack, which was under construction when he was here in 2013.  Jack arrived right on time at 8:30 AM, walked through the job with both of us, and then spent most of the rest of the day cleaning.  Jack works hard and always does a nice job.

Once Jack was squared away we bagged up the pieces of carpet and pad from the bus that would not fit in the trash container and took the container and the bags to the curb.”  (We live on a dirt road and don’t really have curbs, but it doesn’t sound right to say we took the trash to the edge of the street.)  We then unloaded the box from my car with the garden trailer I bought at Lowe’s yesterday, opened it, removed all of the parts, and assembled it.  Linda broke down the cardboard packaging, gathered up some other cardboard and our usual recyclables, and we loaded them into my car to take to Recycle Livingston later.

Keith Kish (Kish Lawn Care) showed up mid-morning to finish cutting our grass.  His Hustler zero-turn riding mower was not repaired yet but he borrowed an articulated stand-behind mower from his son.  Something failed in the hydraulic pump on his Hustler and blew a 1 inch hole in it.  The cost to replace the pump and put the mower back in service will be significant but his business is primarily based on that machine.

I mostly puttered in the bus while Jack worked in the house and Keith worked in the yard.  Linda eventually went to the recycling center and then stopped at Lowe’s to buy some plants, pots, and potting soil.  She is going to try growing some tomatoes, which are one of her favorite summer things, and some herbs.  She moved the hummingbird feeder away from our deck and hung it on a stand in the shade of a tree we can see from our outdoor table.

I boxed up the ceramic tile pieces that were still spread out on the floor of the bus and moved the box to the garage.  That stuff is heavy!  I turned on the chassis batteries so I could move the driver’s seat forward to get access to the seatbelt attachment bolts.  I unbolted the two seatbelt straps and removed them so I could remove the last pieces of the old white carpet from behind and next to the seat.  I then reattached the seatbelts, moved the driver’s chair back, and turned off the chassis batteries.  Refinishing the area around the driver’s seat will be its own special challenge and may not get done with tile as I may need something more flexible.  It will not, however, be heavy carpet intended for use on floors.

My next task was to remove the flexible duct adapters from the HVAC chases.  One of them has an AC electrical cable passing through it, so I will have to undo the cable from a nearby outlet box to get the adapter free.  While I was working on these relatively minor tasks I was also thinking about furniture options.  It finally dawned on me that we did not have buy an expensive custom made sofa-bed or use chairs instead and try to figure out how to finish that area.  I could build a simple but very effective sofa out of wood and have a bottom and back cushion made to the exact dimensions we need using a fabric of our choice.  That opened up the possibility of the fabric matching whatever we get on the chairs.  The seat cushion could double as a bed for one person, with the back cushion removed, and the seat could hinge up to reveal a large storage area rather than dealing with the complexity of a drawer on suspension glides.  The HVAC supply and return could also be easily be accommodated and I would not have to figure out how to finish the chase or conceal all of the wires that run along the floor in front of the chase.  I discussed the idea with Linda and she liked it.

I moved the dinette table up front and we considered its size and placement relative to the seating we would like to use on the passenger side of the coach across from the sofa. We agreed that one of the things we would do while we are at the GLAMARAMA rally is visit Lambright Furniture in Shipshewana and Bradd & Hall in Elkhart.  We also discussed buying a carpet remnant and trimming it to fit in the front part of the bus while we attend the GLAMARAMA rally.

I called Butch to see how his cataract surgery went on Monday.  Apparently it went well, at least his world is suddenly brighter and more colorful.  We talked through various bus projects, including approaches I might take to get a flat, level underlayment for the floor tile.

Keith wrapped up his work, collected his payment, and moved on to Sean’s yard just north of ours.  I suggested that he come every week instead of every other week as long as the grass is growing as quickly as it has the last two weeks and he agreed.  Keith normally does a nice job with our lawn but was now a couple of days behind schedule and trying to catch up using equipment that was not his.  He did not want to drive the stand-behind mower over or near gravel, so some areas along the pull-through driveway did not get cut.  He was also not able to work around obstructions as tightly as he can with his zero-turn mower, and appeared to not overlap some rows.

Jack wrapped up his work not long after Keith and took off for another short job before calling it a day.  I let the cats back into the house and then decided to get out our self-propelled Honda walk-behind mower and trim up the yard in front of the house and some of the areas Keith had missed.  It took a while to get the mower started but I eventually did.

Linda made a nice salad and baked an Amy’s pizza for dinner.  It was 6:30 PM by the time we finished eating.  Linda gathered up the plastic wine glasses and toilet paper holders she bought yesterday at IKEA and we drove to the store in Canton to return them.  The glasses were too tall to fit in our wine glass display case in the bus and the toilet paper holders did not fit in the places we needed them to go in the house.  While we were at the store we looked at their selection of refrigerators, none of which will fit through the entrance door on the bus, and just wandered through looking for ideas.  We were not up that long after we got home, it having been a long but productive day.

 

2015/05/19 (T) More Ceramic Tile

Leave a reply

We were up by 7:30 AM.  A cold front moved through here last night with gusty winds and much cooler temperatures.  The overnight low was 49 degrees F so I closed up the house and made coffee while Linda got ready for her girl’s day out with our daughter, Meghan.  We had toast for breakfast and enjoyed our coffee in the living room to the warmth and glow of the gas fireplace logs.  We both agree that this was a good purchase.

Linda left round 9 AM.  I put a load of towels in the washing machine and then called Kate at work.  I left a message asking her if she would check with Brian about an X-Plan PIN.  I then returned a phone call from Kelly at Brighton Ford and had a nice chat about the F-150.  She worked hard to provide me with additional pricing information as a follow-up to our meeting with Frank on Saturday.  She was able to get the price on an in-stock $46,000 F-150 XLT 4×4 off-road down to $40,000 (with X-Plan but before tax, title, and destination charges).  Six grand is a significant difference, and the F-150 is a nice truck, but forty grand is way more than we were thinking about spending on a vehicle.

Kate called me back while I was on the phone and I returned the call as soon as I finished talking to Kelly.  Kate had already checked with Brian and he was willing to get us a PIN.  One of the odd things about shopping for vehicles in Michigan, especially the Detroit area, is that Ford, GM, and Chrysler all have several “plans” that provide non-negotiable pricing for employees, vendors, and family/friends.  These plans are so widely available that dealers practically assume that you have access to one of them.  I think Ford is making good vehicles and the availability of X-Plan pricing certainly makes them that much more attractive.  Unfortunately they are not selling the mid-sized Ranger in North America, just Europe and Australia.  Mid-size trucks are more our size.

View of kitchen floor looking toward rear from living room. Black Ceramic tile has been removed to just past the refrigerator.

View of kitchen floor looking toward rear from living room. Black Ceramic tile has been removed to just past the refrigerator.

I moved the towels to the dryer and then got to work in the bus.  The high temperature today was forecast to be 57 degrees F so I figured it would be a bit more comfortable working on the ceramic tile removal.  I opened all three roof vents and set the front and middle fans on exhaust.  With the front door open there was plenty of airflow.  I put on my Tyvek jumpsuit and gloves and carried the unbroken tiles I got out the last couple of days to the garage for safe keeping.  I then put the pieces of the ones I broke in a laundry basket to get them off the floor.  They will eventually go in small boxes for disposal.

With all of that material out of the way I vacuumed up the small pieces and tiny shards as best I could along with carpet pad staples and tiny pieces of carpet, pad, and wood.  I then removed the small base molding from the hallway which turned out to be more difficult than I expected.  I put on my safety glasses and face shield, grabbed my floor chisel and 3-pound sledge hammer, and continued removing tiles from the floor.

Getting the tiles out of the hallway was more difficult than the kitchen/dining area.  The narrow hallway limited the directions from which I could position and strike the floor chisel and the result was a much higher percentage of broken tiles.  I did a little better as I moved into the area in front of the bathroom and bedroom doors and then into the bathroom.  I stopped when I got to the tiles under the toilet.  I will have to remove the toilet to get those tiles out and that is not going to happen until after the GLAMARAMA rally.  I do not to remove and reinstall the toilet more than once so it will not get reinstalled until after the new floor is in place.

It was 1:30 PM when I quit chiseling for the day and I left the cleanup for next time.  I got cleaned up and went out to take care of errands.  I picked up our freshly roasted coffee beans from Teeko’s, had French fries at McDonald’s for lunch, and then went to Lowe’s.  I was looking for some sort of grinder to grind down the thinset mortar that is adhered to the plywood subfloor but did not buy one.  I bought a wheeled cart to pull behind our lawn tractor instead.

By the time I got home Linda had returned from her girl’s day out.  She showed me all of the things she bought at Ikea, including four long-stem plastic wine glasses.  We took them out to the bus but they would not fit in our wine glass holder.  She also saw an 18 cubic foot refrigerator (Frostig) that might fit in our fridge alcove.

I turned on the gas fireplace logs, made some tea, and put a second load of towels in the washer.  We sat in the living room researching the IKEA refrigerators on our iPads to the warmth of the fireplace.  I had searched for roof access hatches this morning and found several places that sell them online so I showed that to Linda.  I need to call Pat at Apex Roofing and discuss thus approach.

For dinner Linda made very nice salads with raspberries and walnuts.  She then heated up the leftover risotto and lightly sautéed baby carrots as a side dish.  We sat in the living room after dinner for a while and then watched the 1st and 2nd episodes of season 1 of A Touch of Frost.  Although not a BBC production, it was very engaging.

 

2015/05/18 (M) Ceramic Floor Tile

Leave a reply

I plugged my laptop in, started it, put a load of laundry in the washer, and then made our morning coffee.  We are finally running out of the six pounds of beans we had shipped to us in Quartzsite, Arizona at the end of February and will need to get more from Teeko’s sometime soon.  While we were enjoying our morning coffee I pulled up some information online on how to remove ceramic floor tiles.  What I found was a bit discouraging but what was clear was the need for certain equipment and safety precautions.  Linda needed to return the Sherlock DVDs to the Howell Library today so we went on an errand run to Howell.

At the Library we did some more vehicle research in the April 2015 Consumer Reports.  The Chevy Colorado / GMC Canyon mid-size pickup truck was Motor Trend Magazine’s 2015 Truck of the Year, but being a new model CR had no data on predicted repairs or user satisfaction.  Ditto for the 2015 Ford F-150 and its 700 pound lighter aluminum body.  We liked the size of the Nissan Frontier but the manual transmission required for four-flat towing behind our bus will keep us from buying one.  We have not looked at the Colorado/Canyon yet but it is similar in size to the Nissan Frontier.  CR gave good marks to most of the Subaru models and the Forrester was one of their top picks.  Years ago we wanted a Subaru Outback but they were always just slightly too expensive.  Compared to the vehicles we have been looking at recently, the Subaru’s are less expensive.  Right now, however, we are focused on the utility of a 4-door pickup truck.  Yeehaa!

We checked out the DVDs for Season 1 of the British detective series A Touch of Frost. It is not a BBC production so we will see how we like it.  We stopped at D-R Electric Appliance Sales and Service just up the street to look at refrigerators.  We bought our new gas range/stove from them last September.  They had a 16 cubic foot top-freezer GE (GTE16GTHxx) whose dimensions looked like they might work.  With the doors removed it was under 26″ deep so it would fit through the door of the bus sideways.  It is available in white, black, and stainless steel.  Kurt Richards helped us and said he would search the units he can order if I give him the dimensions of our enclosure.  D-R Electric Appliance is not a dealer for Fisher and Paykel so we would have to get one of those through Lowe’s if we decide to go that route.

Lowe’s was our next stop.  Linda looked at plants but decided not to buy any on this trip.  We picked up a couple of 40 W appliance bulbs for the microwave as one of the two bulbs that lights the top of the range burned out the other day.  I picked up a new face shield, dust masks, a Tyvek jump suit, a floor chisel with shield, and a 3-pound short-handle sledge hammer.

Teeko’s Coffee and Tea is kitty corner from the Lowe’s/Walmart shopping center so we stopped there and ordered one pound each of our three half-caffe blends: Sweet Seattle Dreams (Seattle Blend + Sweet Dreams decaf blend); Ethiopian Yirgacheffe, and Cafe Europe.  Jeff wasn’t there but his mom (Mary) took our order and his dad (John) was starting to put together the roast when we left.  I will pick the beans up tomorrow afternoon.

By the time we got back to the house it was time for lunch so Linda fixed grilled “cheese” sandwiches.  She is still using up the non-dairy cheddar cheese we bought a while back.  It is not Daiya brand and it does not taste like cheddar.  Actually it doesn’t taste like much of anything.  Keith was there mowing the yard as we thought he might be.

Me in the Tyvek jumpsuit removing the black ceramic floor tiles. (Photo by Linda.)

Me in the Tyvek jumpsuit removing the black ceramic floor tiles. (Photo by Linda.)

[p1 L] It was once again 1 PM by the time I got to work in the bus removing the black ceramic floor tiles.  I suited up and Linda took a couple of photos.  I was over dressed under the Tyvek jumpsuit so I changed into something cooler.  Even then it was a hot, sweaty afternoon.  Houses get wrapped in Tyvek to prevent air movement between the interior and exterior, so a jumpsuit does not really breathe.  Neither did I with the dust mask in place so I settled for my wrap-around safety glasses, full face shield, Tyvek jumpsuit, and leather gloves.

I had hoped to get most of the floor tiles out intact.  They are nice 12″x12″ black ceramic with a hint of silver flake in them and they were probably expensive when they were installed in the bus in 1990-91.  They were installed just the way they would be in a house, on a troweled bed of thin set mortar, with one difference; they were set directly on the factory original plywood subfloor of the bus rather than on an underpayment layer.  The information I found online this morning indicated that removing tiles installed this way might require removal and replacement of the subfloor.  That is not an option in the bus so I was curious, and a bit nervous, to see how they would come out.  The other caution was to NOT smash them with a sledge hammer to break them into smaller pieces for easier removal, even though there are lots of websites that tell you to do this.  Ceramic tiles with a high quartz content will shatter sending tiny razor sharp shards flying in every direction; thus the Tyvek jumpsuit, face shield, and gloves.

I took a few tiles out yesterday and most of them came out intact.  The first few today, however, came out in two or more pieces.  Either way I was committed to removing them, so I kept at it.  I developed a technique that seemed to work more often than not.  I would chisel along one free edge and when I got the first indication that the tile was loosening I would switch to an adjacent free edge (if there was on).  Proceeding in this manner I was able to work my way down a row getting most of the tiles loose in one piece.  The tiles were laid in rows with aligned joints running across the coach and staggered joints running the length of the coach.  Thus the rows were short and easier to work on, my work was interrupted by something I will describe next, but I returned to the task and removed the tiles from the entire kitchen/dining area back past the refrigerator.  This part of the deconstruction will take a while but based on the progress I made today it will not take as long as I thought it might, all things being equal (which they never are).

While I was working Keith came to the bus in need of some assistance.  His zero-turn Hustler mower had quit moving and started smoking and was stranded in the northeast corner of our yard.  This particular mower is all hydraulic; the gasoline engine simply turns a hydraulic pump and fluid pressure is used to drive/steer the mower and turn the cutting blades.  Keith had oil on his arms and needed some paper towels.  He suspected a hydraulic hose had failed and the smoke was from the hot oil.  The immediate problem, however, was to get the mower back into its trailer some 400 feet away.

Keith got the mower stuck once last year in wet/soft soil along the north property line.  I was able to use our Cub Cadet lawn tractor to pull him out then so we figured we would try that again.  Just this past weekend I had charged the starting battery and moved the lawn tractor outside to make room in the garage for the furniture we took out of the bus.  It complained for a moment and then started up.  Keith had tow straps so I drove it over to his mower and we hooked the straps to the trailer ball on the back of the lawn tractor.

Keith’s mower weighs 1,200 pounds.  I doubt that our Cub Cadet weighs half that much even with me sitting on it.  I was able to pull it part way across a level-to-slightly-downhill part of the yard but once we hit an upslope my back tires started to slip.  Keith went to get Linda because the lawn tractor would stop if I got off and I was too far from the house to conveniently jump start it.  I continued to drive while Linda helped Keith push although we should have figured out a way to trade places.  It was very hard work for them but the Cub Cadet proved to be “the little engine that could” and we got the mower down by the third culvert (where the driveway for the barn is supposed to go).  We chose that location because it was downhill and close to Keith’s truck and trailer.

Keith’s trailer has a large rear ramp and pointed front like the bow of a boat with smaller ramp that opens at an angle on the driver’s side.  I tried pulling his mower up the rear ramp into the trailer.  The plan was for me to drive out via the front ramp.  Unfortunately the Cub Cadet could not maintain enough traction.  We unhooked it and I drove out the front and put it back in its parking spot.  I got a pair of wheel chocks from our bus and placed them in front of the trailer wheels while Keith unhooked the trailer from his truck.  He then attached the tow straps to the trailer ball on his truck, brought them I through the front ramp opening just off the nose of the trailer, and tied them around the front frame of the mower.  It took a few tries, and one repositioning of the strap on the mower, but Linda and I were finally able to guide it into the trailer while Keith pulled it up the ramp with his truck.

Linda got water for all of us while I helped Keith reload the trailer.  Keith is retired and doesn’t mow lawns for the money.  He’s a good guy who charges us a very reasonable price for the service he provides and we were glad to help him get his mower back in his trailer so he could go home, take a shower, and have a cold beer.  We should have done the same, but he probably took the trailer someplace to have the mower fixed and we both went back to what we were working on.

By 4:30 PM I was too warm and too sweaty to remove any more tiles.  I was also at the point where I was starting down the hallway and needed to remove some quarter round base molding that was installed over the edge of the tiles.  Tomorrow I plan to work earlier in the day when it is cooler, but I say that every day.

Linda cooked most of our dinner on the outdoor grill using the grilling mat to cook potatoes, zucchini, and Japanese eggplant that had been sliced in half lengthwise.  She also made Farro and served it as a side dish.  I think that is the first time she has done that; she normally uses it as an ingredient.  While the vegetables were grilling we sat quietly on the back deck enjoying the last of the first bottle of 2013 Egri Merlot we bought at Whole Foods last week.  The robin eggs in the nest under our deck have hatched so we are trying not to disturb the parents too much.  They need to fly back and forth constantly to feed their young but are understandably weary of us.

I had a call after dinner from Darin Hathaway, the Aqua-Hot technician who worked on our unit in June 2014.  It appeared to have an intermittent ignition coil then and would not fire at all when I had the bus a Butch and Fonda’s in the fall.  Butch and I replaced the burner in October 2014 with the one I bought from him.  That burner was running rich until I replaced the blower bearings while we were in Quartzsite.  Old bearings = slow fan speed = inadequate air supply = rich air:fuel ratio = inefficient combustion and sooty/smoky exhaust.  I still need to repair the original one but for now that is not a priority.  Darin said he could bench test/repair it but Lloyd DeGerald has the same capabilities.

Butch had eye surgery this morning at a clinic in Indianapolis.  I will call tomorrow and see how he is doing.  Linda is having a girl’s day out with our daughter tomorrow, Jack will be here to clean the carpets on Wednesday, Linda has to go to the bakery on Thursday, and I have to take the cats to the veterinarian Thursday afternoon.  I also expect Keith will return sometime this week to finish mowing the grass.  Saturday morning will be our usual ham radio club breakfast and Linda invited Steve and Karen for dinner on Saturday.  Somewhere in there we will probably go look at the Chevy Colorado (GMC Canyon), Toyota Tacoma, and the Subaru Forrester and Outback.  In between all of that I will be doing a load of laundry or two, working on the bus floor, and trying to figure out refrigerators, furniture, and wall treatments, so it is shaping up to be a busy week.  Heck, it’s going to be a busy summer, and maybe a busy fall.

 

2015/05/13 (W) Dental Deconstruction

Leave a reply

We were both up at 7:30 AM.  I made tea instead of coffee and we had a light breakfast.  We both had 11 AM appointments with our dental hygienists and left a 9:35 AM to drive to Dearborn.  We had only gone a couple of miles when we realized we did not put the trash can at the curb so we went back and did that.

Traffic was light and we arrived at Gusfa Dental at 10:50 AM.  My hygienist, Michelle, took me in right away.  Linda’s hygienist, Margaret, took her in on time.  We both had good checkups with no new issues found or procedures required.  The tooth that has been bothering me occasionally all winter may be the one on my upper left, second from the back, that had the root canal last fall, followed by a crown.  Dr. Steve did not see any problem on the x-Rays or exam but said that my various complaints could all be associated with a small but persistent infection at the base of the root canal.  I am due for a 6-month follow-up visit with the endodontist anyway, and was putting off scheduling it until I had my regular checkup today.

It was 12:30 PM by the time we left the dental office and we were both hungry.  We wanted something other than fast food but considered going to Neehee’s Indian diner on Ford Road.  We decided not to go there as it was not very good the last time we went and they had changed the menu, eliminating some of our favorite dishes.  It is also several miles west of I-275 and that stretch of Ford Road is always congested and annoying to drive.  We stopped at the Macaroni Grill at 7 Mile Road and Haggerty Road instead.  We have always found the Macaroni Grill restaurants to be acceptable Italian food in a slightly quaint setting.  Today was no different.  Linda had rigatoni with arrabbiata sauce (spicy tomato), garlic, mushrooms, and spinach.  I had capellini with garlic olive oil and the same add-ins.  We had our fill of fresh baked bread to go with the pasta and were very full by the time we finished lunch.  We used to eat like this a lot more often which is part of the reason we both had a weight problem.

We thought about stopping at Brighton Ford to pick up some literature on the F-150 but decide to drive to Lowe’s at I-96 and Latson Road instead to look at refrigerators.  The smallest one they had on display was 14.3 cubic feet which gave us a chance to see the approximate size of the 13.5 cubic foot Fisher & Paykel.  The F&P is narrower and slightly taller than the one’s at the store, but has a bottom freezer drawer and fits our available space much better.  Lowe’s can order the F&P and it will take two weeks to get.  If I decide to do the fridge swap at Butch and Fonda’s place in Indiana we will have to pick up the F&P in Kokomo as that is the nearest Lowe’s.

Driver side sleeper sofa in our H3-40 with motorized drawer removed.

Driver side sleeper sofa in our H3-40 with motorized drawer removed.

When we got home I changed into my work clothes and worked in the bus.  After emptying the drawer under the jack-knife sofa and removing the APC UPS from under the foot rest area I removed the drawer, footrest cover, and front end panel.  I then removed the two HVAC duct transition boxes and then the two drawer slides.  With all of that out of the way I was finally able to remove the four 1/2″ lag screws from the four corners that secured the sofa to the floor.

Driver side sleeper-sofa with forward end panel and HVAC adapter box removed.

Driver side sleeper-sofa with forward end panel and HVAC adapter box removed.

Getting all of the furniture out will be much easier if we remove the front passenger seat so I worked on that next.  I had never looked carefully at how it was installed until now.  The chair has a 12″ wide x 15″ deep base plate that is bolted to the floor.  The bolts stick up from below and the nuts go over them.  I could not see the studs but I could feel the ends and eventually realized that Royale coach had installed the carpet OVER the base plate.  To remove the seat I would have to remove the carpet or at least cut it and fold it back.  The carpet had to come out eventually anyway and be replaced with vinyl tile so I removed it.  It was more work than it sounds, and took quite a while, as there was not a lot of room to work under, behind, or to the left of the seat, but I got that piece of carpet out.

Villa passenger seat in our H3-40 showing inside edge of mounting plate and studs with nus. (Front of coach to the left).

Villa passenger seat in our H3-40 showing inside edge of mounting plate and studs with nus. (Front of coach to the left).

Removing the seat will now be a simple matter of loosening four nuts and lifting it off the studs, except for the fact that it is heavy.  The studs are presumably the threaded ends of T-bolts with the “heads” in two channels, front and rear, that are installed across the floor.  There is an opening at one end of each channel that allows the T-bolts to be inserted/removed.  My presumption is that all of this is Prevost factory designed and built, not something Royale Coach did, but the driver’s seat does not appear to be installed the same way, so maybe not.

Power base for Villa passenger chair in our H3-40. This thing is complicated!

Power base for Villa passenger chair in our H3-40. This thing is complicated!

I finished working in the bus around 7 PM, put my tools away, and closed up the coach.  As a consequence of our big lunch we were not hungry and skipped dinner.  I called Butch to discuss the project and get some advice.  I then called Chuck and brought him up-to-date.  We finished the evening by watching Season 2, Episode 3 of Sherlock on DVD.

 

2015/05/01 (F) May Day

Leave a reply

Wow, another month gone.

We got up after 8 AM this morning, were having coffee, and had not yet had breakfast when I got a call from Diane at SteelMaster Building Systems.  They are certainly prompt in their follow up as I just submitted an RFQ last night via their website.  I had a very informative conversation with her that left me favorably impressed with the company and inclined towards their products should we decide to build our barn this way.  By the time I finished with her and we spent time studying SteelMaster’s website we sat down to have breakfast at 9:45 AM.

I started a load of laundry and puttered at my desk until Linda had chores for me to do.  She vacuumed the main floor and tidied up the kitchen in advance of tomorrow’s dinner visit with John and Diane and wanted to take the storm door insert out of the front entrance frame and put in the screen.  We like fresh air and have an abundance of it out here in the country.

We drove to the Sears Outlet at Fountain Walk in Novi to buy a box spring mattress foundation.  They were already discounted and also on sale.  The shipping was 50% of the sale price but we could not get it home in our car so that was our only choice.  It was still a bargain and we will have it next Tuesday.  We have been using the heavy, elaborate foundation that came with our Sleep Comfort mattress years ago, but it is broken and needed to be replaced.

We stopped at Lowe’s on the drive back to look at vinyl floor tiles and bought some Oxygenics shower spray heads and soap.  We took a drive up Latson to see if we could find a metal arch garage that Phil Jarrell had recently spotted.  We think we caught a glimpse of it on the west side of the road as we headed north towards M-59.  Heading east on M-59 we took a detour up Argentine Road to see if we could find Phil’s place but never saw anything we felt confident was his.  We headed east on Clyde Road and took Old US-23 back to M-59 where we stopped at Kroger for a few things before returning home.  To Linda’s surprise and delight, the Kroger has some of the mock dairy vegan products, like Daiya cheeses, that she occasionally uses and cannot get at Meijer’s.

Linda had an agenda for today and next up was putting the umbrella in the outdoor table.  Once that was taken care of we sat outside enjoying blue skies, bright sunshine, an air temperature of 71 degrees, and a slight breeze, none of which required the umbrella, but the point was to get it off the floor in the library where it was stored all winter.  Next we moved the natural gas grill from the garage to the lower rear deck, reassembled it, and connected it to the gas supply (it has a quick connect and shutoff valve).  I then busied myself removing the three shower heads and replacing them with the removable spray heads we bought at Lowe’s.  If I did not do that right away they would still be sitting around in their boxes months from now.

Linda used the grill to make dinner.  She grilled seasoned Brussels sprouts, tofu hot dogs, and bananas sliced in half the long way.  This will be the first summer in a long time that we have had a grill.  Linda is excited to have it as it expands her cooking options and provides a way to not heat up the kitchen in the warmest weather.  I am looking forward new dimensions in our meals.

I had planned on reviewing an article for BCM but ended up involved in two phone calls after dinner.  One was with Pat Lintner from GLAMA and our GLCC chapter and the other was with Lou Petkus from the SKP Photographers BOF.  That left just enough time to watch Season 1, Episode 1 of Sherlock on DVD before turning in for the night.

 

2014/09/25 (R) Two M’s

Leave a reply

Linda made zucchini bread and muffins a week or so ago.  We ate all of the muffins within a couple of days but she froze some of the bread.  She took the bread out of the freezer last night to let it thaw so we could have it for breakfast this morning.  She warmed it up and made a fruit salad to go with it, along with our usual fruit juice and coffee.  Marilyn took advantage of her visitor status and slept in so we had breakfast without her and she ate when she finally got up.

Madeline in her sofa-bed with her Winnie-the-Poor sleep sack.

Madeline in her sofa-bed with her Winnie-the-Poor sleep sack.

I was working on the electrical outlets in the garage when Brendan arrived at 9:45 AM with Madeline in tow.  Meghan arrived around 10 AM, so Madeline had all the “buddies” here to admire her.  I finished my electrical work, touched up some drywall compound, and then got cleaned up.  I was once again the designated reader and got to read three books to Madeline.  She had lunch at noon and her dad got her down for a nap around 12:30 PM.  Meghan is still experimenting with foods, so she left to do her grocery shopping on the way home.

The "buddies" (L-2-R): Brendan, Marilyn, Meghan, and Linda. (Not shown: Bruce, taking the photo.)

The “buddies” (L-2-R): Brendan, Marilyn, Meghan, and Linda. (Not shown: Bruce, taking the photo.)

Brendan stayed for lunch and a long chat.  He was thinking about leaving when he decided to check out my old Toyo view camera.  He figured the students in his history of photography class at the University of Michigan had probably never seen one and wanted to take it in for them to see.  He also wanted to have it at his house to play with.  We found it and checked that all the parts were there and he loaded it into his car along with the tripod and dolly (studio roller base).  Madeline started to wake up so he made his exit.  She doesn’t seem the least bit concerned if he’s not here when she wakes up, but is momentarily distressed if she sees him leave.

Flowers along the Mill Pond boardwalk (Brighton, MI).

Flowers along the Mill Pond boardwalk (Brighton, MI).

Madeline is spending the night tonight so we will two M’s here the rest of the day and tomorrow morning.  Linda and Marilyn will take Madeline back to Ann Arbor tomorrow in time for lunch and her 1 PM nap.  Madeline has swimming on Fridays at 4 PM so Linda and Marilyn will leave before that and stop at Whole Foods Market before taking Marilyn to Detroit Metropolitan Airport for her evening flight back to St. Louis.

I took a few minutes to check e-mail while Madeline was napping.  This morning I had tightened up the Wordfence parameters on the FMCA-GLCC site and switched the caching from the faster Falcon Engine to the Basic setting in order to fully activate country blocking.  I only had a few failed login attempt e-mails so I think it made a difference, but only time will tell.  I also white listed our own IP address to make sure we did not get locked out if we mis-typed our login credentials.

Madeline with Grandma Linda on the Brighton Mill Pond boardwalk.

Madeline with Grandma Linda on the Brighton Mill Pond boardwalk.

I had an e-mail from my niece, Amanda, with a couple of pictures of her daughter, Lilly, a very pretty and sweet-tempered child about six weeks younger than Madeline.  We saw them in late June and will like try to visit again en route to the southwest this winter, weather permitting.  If not, we will certainly try to stop in the area on the way back in the spring.

When Madeline awoke from her nap we let he play long enough to fully wake up and then we all went to downtown Brighton.  We walked the boardwalk along the east edge of the Mill Pond and saw a Painted Turtle, an egret, some fish, and lots of ducks and geese.  We then took the pedestrian bridge to the west side of the pond where the playscape is located.  The playscape is a wonderful place with structures built to suggest animals and Madeline explored it thoroughly with Grandma Linda’s help while I took pictures.  It also has an area with chalk boards and a mailbox full of sidewalk chalk that the kids can use to draw.  Madeline spent quite a while trying all the different colors.

Madeline with Grandma Linda at the playscape by the Brighton Mill Pond.

Madeline with Grandma Linda at the playscape by the Brighton Mill Pond.

We stopped by Lowe’s on the way home to return the spark plug I bought last night and get the correct one.  By the time we got back to the house Madeline was hungry so Linda got her dinner ready right away.  For our meal Linda prepared a green salad with sunflower seeds and dried cranberries topped with Ken’s Sweet Vidalia Onion dressing (one of our favorites) and a one pot meal of quinoa with black beans, corn, and onions.  Linda and I finished the Red Guitar Sangria with dinner (Marilyn does not drink alcoholic beverages).

Madline working with chalk at the Brighton Mill Pond playscape.

Madline working with chalk at the Brighton Mill Pond playscape.

Madeline played quietly with Linda for a while as I chatted with Marilyn. Before we knew it, it was time for Madeline to go to bed.  The time between dinner and bed always seem short compared to other intervals during the day.  She is always very good about bedtime and went without a fuss.  Linda spent about 30 minutes getting something ready to e-mail to the bakery software vendor while Marilyn played Words With Friends and I researched where we could buy more Red Guitar Sangria.  It is available at the Meijer’s stores in our area and is very reasonably priced so we will probably get some more.  We had apple crisp for dessert after which Linda and Marilyn played three-way online Scrabble with each other and their brother Ron in Pennsylvania.

 

 

"I think this color goes right here."

“I think this color goes right here.”

Madeline is a very good-natured and relatively calm child but when she is awake she is full engaged with the world around her.  We were all tired after a long but very satisfying day of visiting and turned in without watching any TV.

 

2014/09/20 (S) Bus Talk

Leave a reply

All days have the same number of hours.  How those hours are divided up between light and dark, awake and asleep, busy or at leisure, varies with each day.  Basically, our day went like this:

  • We went to our weekly SLAARC breakfast in South Lyon.
  • We returned home so Linda could get to work on the bakery software conversion project.  She did that all day except for a break to go for a walk.
  • I called D. R. Electric Appliance to check on the range.  As I had figured it did not arrive yesterday (they would have called if it did).  They supposedly ordered it on Tuesday and told me it would take three days to get.  They do not receive product on the weekend so maybe Monday.
  • I worked at my desk on editing and uploading blog posts until 11:30 AM.
  • I went to Recycle Livingston with our weekly load.
  • I stopped at Lowe’s for a 250VAC/15A circuit breaker, outlet, and box.
  • Lowe’s parking lot connects to Walmart’s parking lot, so I stopped there for ICE brand flavored sparkling water and picked up a couple of bottles of  Leelanau Cellars Witch’s Brew seasonal spiced wine.  We had this last fall and enjoyed it.
  • When I got back to the house we had a light lunch of sourdough pretzel nibblers and hummus and then resumed our work.
  • By mid-afternoon I was tired so I took a nap.  I often do better sleeping when I’m tired rather than when I am supposed to sleep.  I also wanted to be rested enough to enjoy dinner this evening.
  • We met Chuck at the Carrabba’s at West Oaks Mall at 7 PM.  He had arrived ahead of us so we only had to wait about 20 minutes to get a table.  Linda and I both had the Tag Pic Pac, one their two vegan options.  It was long, relaxed meal and a great conversation, some of which was about buses (Chuck and Barbara also own a Prevost H3-40 converted coach).  We pulled out of the parking lot a little before 10 PM.
  • Back home we watched season 5 episode 8 (final) of Doc Martin.

That was our day and did not include construction projects or taking photographs.

 

2014/09/18 (R) Crown Prep Anniversary

Leave a reply

I woke up early and got up at 6 AM.  A two hour nap yesterday afternoon meant I was not going to sleep as many hours last night.  I had also set alarms to make sure I got up, which tends to make me wake up earlier than I might otherwise, almost always before the alarms ever activate.  I awoke to find that iOS8 was now available for my iPad2, so I installed six other updates first, some of which emphatically wanted to be installed before the iOS8 update.  I had some raspberry green tea while they uploaded and installed, e-mailed yesterday’s blog post to myself, updated the beginning of this blog post, and then initiated the operating system update.

I suppose “Crown Prep” might be shorthand for “The Royale Preparatory Academy” or some such place and Crown Prep Anniversary might have something to do with an important event at said place but, alas, in my case it meant, more or less, just what it says.  We bought our converted bus five years ago today, a 1991 Prevost H3-40 VIP shell converted by Royale Coach (Monaco) and finished in the fall of 1992.  I also had a dentist appointment today to prepare my recently root-canaled tooth for a permanent crown.  The appointment was at 8:30 AM some 50 miles away in Dearborn, Michigan, which meant I had to be out the door around 7 AM to allow for the heavy traffic inbound to the metro Detroit area from the northwest.  The traffic was even worse than I expected and I pulled into the dental clinic parking lot at 8:29 AM.  I really hate rush hour traffic and avoided it even when I was working full time.  It is such a colossal waste of time.

The U. S. Census Bureau considers Livingston County to be part of the Detroit Metropolitan Statistical Area (MSA).  Locally, many people think of Metro Detroit as Wayne, Oakland, and Macomb Counties while the MSA includes Lapeer, Livingston, and St. Clair Counties as well.  Washtenaw County to the south of us, where our children live, is not part of the Detroit MSA but is part of the larger Detroit “Combined Statistical Area” (CSA) along with Genesee and Monroe Counties.  Having been “west siders” since we moved to the area from Missouri in 1976, Lapeer and St. Clair Counties have always seemed far away while the communities in Livingston and Washtenaw Counties were much more accessible to us.  When I was working as an engineer I was employed by a company in Livingston County and by three different companies in Washtenaw County, specifically Ann Arbor.

I am not clear on the point at which communities, and individuals in those communities, do or do not think of themselves as living in the “Detroit Metro Area” (DMA) which is quite a different thing from the official U. S. Census Bureau boundaries.  My guess is that Howell very clearly sees itself as distinct from the DMA.  My suspicion is that folks in Brighton are split on this, although the community would no doubt like to be viewed as outside the DMA.  The western half of Livingston County is certainly much closer to Lansing, the state capital in the heart of Ingham County, both geographically and culturally.  Western Livingston County and most of Ingham County are rural/agricultural, except for the greater Lansing and East Lansing area (home of Michigan State University).  The eastern half of Livingston County has long been a place from which people commute to work in metro Detroit.

The fact is that being associated with Detroit has not been viewed as favorable by many people and communities in southeast Michigan since the riots of the late 1960’s.  Those events left deep scars on the people who were here at the time, and for many those scars remain to this day.  Not for us, of course; we were not even here then.  And we are the wrong people to ask about affiliations anyway.  We lived in an apartment in Westland for our first two years here and then bought the house in Farmington Hills where we lived for the next 35 years before moving to the “Browelland” (Brighton, Howell, Hartland) area.  Westland and Farmington Hills are clearly Detroit suburbs, like it or not.

I took a survey and Linda said she thought we still lived in the Detroit Metro Area.  I suppose I think so too, but you won’t find many five acre parcels zoned RA (agricultural residential) in the true suburbs of the big city, nor the dark skies and bright stars we have out here on a clear night.  No, we are clearly not in a suburb of Detroit, but that was not my question.  We are kind of in the country but only minutes from all three of the aforementioned municipalities.  For that matter we are not actually in the cities of Brighton, Howell, or Hartland.  Even though we have a Howell mailing address we are actually closer to both Brighton and Hartland and if we had school age children they would attend the Hartland schools.  And when we lived in the suburbs I did not have to drive 50 miles to get to the dentist, 30 miles to get to our vet or eye doctor, or 20 miles to get to our family doctor.  Of course the drive is about the same to get to our ham radio breakfasts and meetings in South Lyon as it was before and we do not have to drive 40 miles to get to our bus, which is now parked in front of the house.  We are also trying to “shop local” as much as possible, which means we are shopping at a wide variety of places we never patronized when we lived in the suburbs of Detroit.  But I digress.

After I was done at the dentist’s office I drove to our veterinarian’s office, just a couple of miles from our old house, to pick up flea and heart worm medication for our cats.  I took a quick drive through the old neighborhood.  It was a nice place to live and has not changed, at least in appearance.  I had a good experience with the local endodontist last week, however, and today’s drive reminded me that we should probably switch to service providers much closer to home for most of our medical and veterinary needs.  But that is not a decision to be made simply on convenience.  We have used our current providers for over 35 years and given how infrequently we use them we have not been motivated to change.  We have been to the dentist a lot this summer, however, so that at least has us thinking about it more seriously.

I stopped for fuel and then at Lowe’s for a keyless door latch/knob set for the utility closet.  They did not have distilled water and I tried two other places before ending up finding some at Meijer’s.  Linda was preparing lunch when I finally got home and had sorted through and organized a large stack of installation and user manuals I had pulled out of kitchen drawer this morning.  Some were left for us by the previous owners, some were for things we have bought since we moved here, and some were for things we no longer have, or have but no longer use.  We went through a small stack of items she wasn’t sure about and then stored everything we needed to keep in a drawer in the small bedroom closet organizer.

I spent the rest of the afternoon and most of the evening, except for dinner, editing photographs for our personal website/blog and the SLAARC website.  I also took a few minutes to enjoy the last of the apple crisp and a glass of Alpha Rose wine with Linda.  It’s been bugging me since yesterday that I could not positively identify the very distinct nose and taste of this wine, so Linda did a little online research on the King of the North grape.  Both the University of Iowa and the University of Minnesota described it as a vine that grows very well in cold northern climates but is very acidic and has a very “grapey” taste that is not really suitable for making wine.  That information helped me figure out the smell/taste.  It was grape soda; really really good grape soda.  Those descriptions did not alter my opinion of the wine.  I like fruit and I like sweet, and I love the nose and the taste as well as the acidic finish is indeed very clean and refreshing.

Linda was watching episode 1 of Ken Burns’ documentary on the Roosevelts when I came up from the basement, so we watched that instead of an episode of Doc Martin.

 

2014/09/13 (S) Overnight Guest

Leave a reply

Linda’s sister, Sister Marilyn, called a couple of days ago to let us know she would be in the Detroit area on business this weekend.  She wanted to know if we could fetch her this afternoon and if she could spend the night at our house?  The answer was “of course,” of course.  Her flight out wasn’t until Sunday evening, so Linda put the gears in motion and arranged a brunch with the local family for 10 AM tomorrow.

Being Saturday, we went to our ham radio club breakfast in South Lyon.  Before leaving our neighborhood we drove to the other end of the street (dead end with turn-around) to see where the gas hookup crew left off yesterday.  We knew they were working down there today because we saw the trucks leave sometime between 5:30 and 6:00 PM last night.  There’s a chance they will be back today and we wanted to see how close they were to connecting our house to the main line.  It looked like they had quite a few houses to do ahead of ours, so we went to breakfast.

We got home around 10:30 AM to find a crew working in our yard trenching in the branch line to our house.  I was told yesterday they were going to bore it in, so something obviously did not get communicated.  Not only that, they were running a 5/8″ line, which was way too small for the 425 meter we are supposed to get.  I stopped the crew and the guy in charge pulled out his paperwork.  It had “425” written on it big letters, but the drawing showed a 5/8″ line.  He agreed that the 5/8″ line was way too small for that meter and that we should have 1.25″ line.  They pulled the little bit of line they had already run out of the ground, raked out some of the dirt they had already trenched, and moved their machine across the street to trench our neighbors yard.

We were lucky we got home when we did.  They had already cut through some tree roots that did not need to be disturbed and would have torn up a lot more of our yard unnecessarily if I had not interrupted their work.  They were nice about it, but I still found it troublesome that I had spoken to two different supervisors face-to-face about this, one as recently as yesterday, but this crew showed up and did something different than what I had been told, and agreed, would be done.

I was finally going to try to remove the fogged window from the bus today, but we had a lot of rain overnight and woke to overcast skies, temperatures in the upper 40’s, and a forecast high of 57 degrees F with a strong chance of rain through mid-afternoon.  That was not the sort of weather for removing a window from a vehicle parked outside.  Besides, with Marilyn arriving mid-late afternoon I did not want to work on anything messy and then have to get cleaned up.

Linda looked up the kitchen ranges we had been considering.  The GE 30″ 5-burner double-oven convention model (JGB870DEFWW) was on sale again at Lowe’s for $180 off MSRP and we would get another 5% off the sale price by using our Lowe’s credit card.  If we ordered it today delivery would be September 27, longer than I would like, but it is what it is.  We have to order this range because Linda wants a white one to match all of the other appliances in the kitchen and the appliance stores do not tend to stock white ranges with the features we want.  I called our local Lowe’s store and confirmed the free delivery and take away of our current range.  Installation is $20 plus a new flex gas line for $30.

I called TOMTEK HVAC and got hold of Tom.  He seemed put off by the fact that I have someone else doing HVAC work at the house and will have the natural gas already tied in when he comes to convert the main house furnace from propane to natural gas, but he said he would check with Weil-McLain on Monday about what parts he needs to do the conversion.  While on the phone with Tom he suggested that we try D. R. Electric Appliance Sales and Service in Howell for our new gas range.  We looked them up on the web and got their (incorrect) phone number and hours.  I got the correct number from 411 before I realized that it was also on their website.  They closed at 2 PM on Saturdays, so we didn’t make it there today, but I called and got an answering machine, left my name, number, and the reason for the call.  Curt called me back a short time later.  I gave him the model number and he said he would call G.E. on Monday.  He said he had been holding off ordering G.E. appliances waiting for Columbus Day sale pricing.  He figured he would have the range three days from ordering and could probably install it at the end of the week or early next.  They charge $25 for installation and haul away, and $25 for the new flex gas line if we need one, so it’s the same $50 as Lowe’s.  (Lowe’s assured me that they were REQUIRED to install a new flexible gas line.)  That all sounded good depending on the price of the range.  Getting it sooner has some dollar value to us, we’re just not sure how much.

I stayed home while Linda went to Meijer’s for groceries.  Finding the crew in our yard this morning doing work they were no supposed to be doing spooked me enough to not want to leave the house unattended the rest of the day.  As long as I was stuck at home, I called Bratcher Electric to give them a heads up that the gas connection to the house was imminent.  Being Saturday I got their answering machine and left a message.  I also called Darryll at DCM Heating & Cooling and left a message regarding the gas connection.  Once the meter is hung and connected everything else depends on Darryll getting his piece done first.

We checked the website for Country Squire Fireplace and Lighting in Howell and saw a 10% off coupon, so I printed that.  I wanted to go there today and buy a set of high-efficiency vent-free natural gas fire logs but it will probably be tomorrow afternoon instead.  These logs are more efficient than a typical kitchen range and are designed to be used with the fireplace flue closed, throwing most of the heat they produce into the room instead of up the chimney.  Darryll said he would hook it up for us and add a shutoff valve when he came back to tie in to the gas meter, so we need to have it here before he comes back next week.

Marilyn called and said their flights were running a little behind schedule and that Linda should pick her up around 3 PM rather than 2:30 PM as originally planned.  She called back again and said 3:15 PM would be better.  Linda got back from the grocery store and we had a quick lunch of leftover Sloppy Joe’s.

With overnight lows in the 40’s, highs only in the mid-50’s, and the connection of our natural gas somewhat imminent, we decided we could afford to use propane to heat the house.  We have been conscious of our propane use because we did not want to get in a position where we needed to have either of the tanks filled.  I turned the furnace on and set all the thermostats a few degrees above ambient to take the chill off.

While Linda drove over to Lake Orion, Michigan to fetch Marilyn I decided to work at my desk selecting photos for gallery posts on the garage/HVAC project and natural gas work, and worked a little bit on the websites for the FMCA Great Lakes Converted Coaches and Freethinkers chapters.  I really need to have the GLCC site usable in the next three weeks and the FTH site within a month of that. That sounds ambitious even as I write it down and I suspect it won’t happen.

Linda and Marilyn got to the house around 4:30 PM and after we got Marilyn settled in her bedroom we just sat and relaxed and talked for a while.  We thought she might appreciate a good home-cooked meal but we ended up taking her to LaMarsa for dinner.  She had the Koshary, which we had last night, and we split an order of garlic almond vegetable Ghallaba with green salad and crushed lentil soup.  We all ate way too much pita bread with garlic spread and were uncomfortably full by the time we finished our meal, but it was delicious and we did not have to prepare it or clean up afterwards.

These days twilight now comes around 7 PM and it was dark by the time we got home at 8 PM.  I made a pot of decaf coffee and we settled in the living room for a long chat.  I set the thermostats back before we turned in for the evening as all three of us prefer to sleep in a cool room.

 

2014/09/12 (F) Posted

Leave a reply

Linda was up very early to try and beat the morning rush inbound to Detroit from the northwest.  I took an Ibuprofen and went back to bed, finally getting up at 7 AM.  1-800-PACK-RAT was scheduled to pick up the 16 foot long storage container we have had in our driveway for the last two months and I wanted to be up and dressed when they arrived.  I did not have any problems with my teeth overnight.  They felt OK this morning but the upper right was still a bit sensitive to biting pressure.  I had a nice soft banana for breakfast and decided to keep taking the Ibuprofen and Tylenol.

I put a load of laundry in the washer and then ran out to take care of errands.  I stopped at Dunkin Donuts for coffee, Lowe’s for solar salt for the water softener, and then Teeko’s for coffee beans.  Jeff still did not have the Sweet Dreams decaf blend even though he orders it every week.  I got a pound of the Seattle Blend 50/50 regular/decaffeinated, and a pound of regular Brazilian Serra Negra to blend with the decaffeinated beans we already had at home.

Heather, from Root Canal Specialty Associates, called around 9 AM to check on me.  I mentioned the sensitivity and she said that was normal and to keep taking the Ibuprofen/Tylenol through the weekend to counteract any inflammation and/or discomfort.  She wanted to know if I thought the temporary filing was high and making contact before the other teeth.  I wasn’t sure, but she said if it was to call them Monday morning and they would get me in to adjust my bite.

Since I was on the phone anyway I called Bratcher Electric to see about the quote/estimate for the generator service / fuel changeover and the service entrance feed from the transfer switch to the sub-panel to change it into a main panel.  They have been very busy with repairing damage caused by the storms of the last few weeks.  We did not suffer any damage beyond some dead branches breaking off from trees, but south of us folks were hit much harder.  That kind of work always takes priority.

The day was overcast and dreary with morning temps in the mid-40’s and a high of 54, but that was OK; it was a perfect day for sitting at a desk and working on a computer, undistracted by either bad or gorgeous weather.  I did, however, bring my computer upstairs and work at Linda’s desk.  My office is very nice but it is in the basement and it is a bit of a cave.  Sometimes I like that, and sometimes I don’t.  I worked on our blog until early-midafternoon and finally uploaded posts from Aug 2 through Aug 20.

My only interruption was a visit from one of Roese Construction’s field supervisors who was checking on where the runs will go to connect the houses in our neighborhood to the natural gas main.  After looking at our situation he agreed with me and Mel who had looked at this a few weeks ago, that staying to the east of the east entrance to our pull-through driveway made the most sense even through it required them to bore at an angle relative to the main line.  That conversation confirmed that they will be horizontal boring the branch line rather than trenching it in.  He did not give me a firm date, but it sounded like it could be as early as tomorrow (Saturday) and likely by Tuesday next week.

My computer battery was down to under 1 hour of charge remaining, so I took it downstairs and plugged it back in to its power supply.  While I was down there I put another load of laundry in the washing machine.  Back upstairs I made a PB&J sandwich for lunch, along with some green tea.  I got back on the RVillage Mobile development site, played with a few more features, and provided some additional feedback to the development team.  I then worked on this post using my new Logitech Bluetooth keyboard.  The Wacom Bamboo stylus is nice, but the keyboard is the way to go when creating extended text.

Juniper, our female cat, was getting into something in the library so I went to investigate.  She had cornered a yellow jacket and was trying to figure out what to do with it.  I solved the problem for her by capturing it and putting it outside.  I don’t think she was pleased with my solution, but not 20 minutes later she was at it again, and it was another yellow jacket.  We have a nest in the soffit near the library that we need to get rid of, but we have not had a problem with them getting into the house until very recently.  Hopefully that has not changed but I will have to investigate the situation.  It may be that with the onset of cooler temperatures they are finding their way into the library through the recessed ceiling downlight cans.  If so, there’s really no good way to seal those.  Fortunately we can close of the house from the library with a kitchen door and a living room doorwall that includes a screen door.

It started raining very lightly around 4 PM, but never developed into anything.  Linda got home from the bakery at 5:30 PM.  The storage container had not been picked up yet so we called the 1-800 number and left a message with our callback number.  I got a call around 6 PM from the local (Plymouth, MI) office verifying the pickup and address.  The driver arrived around 7:20 PM and had the unit loaded by 7:30 PM.  After he left we headed to dinner at LaMarsa where we had crushed lentil soup and split an order of Koshary and salad.  Even splitting the dish we both ate too much, aided by the fresh-baked pocket bread and garlic spread.   The food and service were both excellent, as always, and the garlic spread was “…the gift that keeps on giving.”

We got back from dinner a little before 9 PM, too late to start any in-depth computer work, but early enough for me to finish this post and for Linda to do some recipe research for Sunday’s brunch.  It seems like only yesterday it was still light at 10 PM at night, but we are approaching the autumnal equinox, and there are noticeably fewer hours of daylight now.

 

2014/09/06 (S) Deliveries

Leave a reply

We were up early and off to our SLAARC ham radio club breakfast in South Lyon.  There was a good turnout and good conversation, some of which had to do with our future tower project.  Mike (W8XH) was driving to the Findlay (Ohio) Hamfest tomorrow morning and had room for one more in his car so I decided to go.

Back home we broke down cardboard, loaded it into my car with the rest of our recyclables, and headed over to Recycle Livingston.  Afterwards we stopped at the Howell Bank of America branch so I could get some cash for the Findlay OH Amateur Radio Club Hamfest tomorrow.  A little farther up the road we stopped at Lowe’s for grass seed and bought three plastic tubs to replace the cardboard boxes we have been using on the floor of the kitchen pantry for recyclables.  Lowe’s is at Latson Road and Grand River Road so we hopped on I-96 East over to US-23 and headed south towards Ann Arbor to drop off the window air-conditioner and visit with our son, daughter-in-law, and grand-daughter.

When we exited US-23 at Washtenaw Avenue the traffic was worse than usual, and it is usually pretty bad.  Ann Arbor got hit a lot harder by the storms last night than we did and two of the three traffic signals between the highway and Stadium Boulevard were not working.  Drivers were being courteous, and everyone was taking turns, but the traffic volume through this stretch of road exceeds its capacity even when the signals are working.

We got the window air-conditioner unloaded and moved to the second floor of the garage.  We had a nice visit that included reading stories to Madeline.

Madeline and Grandma Linda read a favorite story.

Madeline and Grandma Linda read a favorite story.

We were going to stop at the Whole Foods Market on our way home but decided to avoid the traffic jam and worked our way through a subdivision up to Geddes Road and back to US-23.  Back home we had a light/late lunch of leftover rice seitan and mashed cauliflower and then worked for a couple of hours getting things out of the storage pod and organized in the garage.  We moved the shelves away from the northeast wall so Darryll could work on the gas pipe when he returns.  We knew when we put the shelves there that we were taking a small gamble that we might have to move them.  Fortunately they slid easily without being unloaded.  We must have the storage container empty by the time we go to bed on Thursday evening as it is scheduled for pickup on Friday.

For dinner we had a nice salad, roasted Brussels sprouts, and sautéed potatoes with onions, garlic, and bell peppers. We finished the no-bake (frozen) double-chocolate torte for dessert. After dinner Linda played Scrabble and Words With Friends while I researched Acme screws, nuts, and related components that we need to get the ham radio tower fold-over mount operational.

I turned in earlier than usual as I needed to be up at 5 AM in order to be at Mike’s (W8XH) QTH by 6 AM to leave for the Findlay Hamfest.

2014/09/02 (T) No More Painting

Leave a reply

After breakfast Linda worked on the financial and membership records for our GLCC RV chapter and I took care of a couple of e-mails.  Keith showed up to cut the grass, which he managed to do in spite of the wet conditions from yesterday’s heavy rains.  After chatting with Keith for a few minutes I started to resume work on “the project” but decided to look for the tub of grass seed and fertilizer we brought from the old house.  I found it rather quickly and we still had a partial bag of grass seed, so I spread it around the front yard by hand filling in the bare and thin spots, of which there were plenty.  Our flock of wild turkeys was back today.  I think they like the grass seed I put out for them.

Wild turkeys gather in and around the fire pit. No...we do plan to cook them.

Wild turkeys gather in and around the fire pit. No…we do not plan to cook them.

I sanded the drywall compound in the library and applied another thin layer.  I’ve been applying non-overlapping horizontal strips of mud, letting them dry, sanding them smooth while feathering the edges, then repeating the process for the areas in-between, or outside, the previous strips.  I will eventually turn this 90 degrees and apply the strips vertically.  The last set of steps will be to fill around the outside of the opening, feathering everything back to the existing wall surface and sanding it smooth with the central part of the patch.  We don’t want it to be obvious that there was ever a hole in the wall.  Once the drywall patching is done I have to prime the new compound and then paint the entire wall.

The paint on the east wall of the garage and the outside of the utility closet looked good and the paint on the inside of the utility closet looked good enough; it is, after all, the inside of a furnace closet.  I was done painting, at least for now, which should have felt like a big deal, but it just meant I could wrap up a couple of things and move on to the next thing.

The first thing was to mount the electrical box on the wall to the left of the library HVAC unit, make all the wiring connections, screw the switch into the box, and put on the cover plate.  I routed the thermostat wire alongside, and zip-tied it to, the armored AC power cable.  The second thing was preparing the mounting holes for the garage furnace thermostat on the outside of the utility closet wall.  I then cut the thermostat cable to the correct length beyond the wall, removed the outer sheath, stripped the ends of the wires, and secured the cable with a zip tie to prevent it from slipping back into the wall.  I did not actually mount the thermostat, however, since I was going to wait for Darryll to connect the wires.

Three adults and three young. They are large and impressive birds.

Three adults and three young. They are large and impressive birds.

By then it was time for lunch, after which Linda left for her dentist appointment in Dearborn.  I wanted something easy to do, so I assembled the three plastic shelving units I bought at Lowe’s yesterday.  They went together easily, but one was missing the feet, top caps, and wall brackets and another one had a defective top cap.  I put them against the east wall of the garage and the floor was flat enough that they lined up well, so I don’t necessarily need the feet.  But the top caps are important, and it bugs me that I did not get everything I paid for.

The next thing I decided to tackle was the wood box in the utility closet that will enclose the electrical sub-panel and make it appear to be recessed and hide all of the electrical cables.  I cleared off the table we have been using to work on sheets of drywall and stood the scrap pieces of drywall against the back wall.  I got the two 8-foot 1×10’s I bought yesterday, put them on the table, made careful measurements and then marked them.  The two side pieces needed to be 52″ long x 7-1/4″ wide, with notches to create clearance for the top plate, horizontal blocking, and electrical cables passing through holes in studs.  I cut them to length with the Rockwell circular saw, and then ripped them to width using the Craftsman band saw.  The band saw had not been used in years but it had no problem ripping each board.  The notches were made with our Porter-Cable saber saw.  This kind of work is a pleasure when you have the right tools.

I screwed the two side pieces into place and then measured and cut a bottom cross member, and a trim strip to go below it, and installed those with screws.  I then cut a top cross member and a backing strip to go behind it between the two side pieces.  When I was done I had a box that would support a 48″ high by 33″ wide 1/4″ thick plywood panel with the outside face flush with the front edge of the sub-panel once I cut a rectangular opening in the plywood to allow it to fit around the box.  The plywood panel will be secured around the edges with a few screws and the sub-panel cover plate will overlap and cover any gap between the panel box and the opening in the plywood.  I will finish the plywood panel tomorrow or Thursday depending on when Darryll returns and how much I have to work with him to get the power connected to the new A-C compressor.

Jasper the cat in the kitty tent on the deck. He spends a lot time looking around and sniffing the air when he is out here.

Jasper the cat in the kitty tent on the deck. He spends a lot time looking around and sniffing the air when he is out here.

That was the end of my project work for the day so I took a shower and put on some clean clothes.  Linda poured a couple glasses of wine and we sat on the deck and enjoyed an absolutely beautiful late summer Michigan evening.  We brought the kitty tent out so Jasper could sit outside with us.  Linda threw a green salad together, followed by the leftovers of the penne pasta dish and Italian bread she made for dinner on Saturday.  As twilight set in we moved inside and I decided to go to Lowe’s for some grass seed.  I figured if the soil was still moist first thing tomorrow morning I would spread it around the bare and thin areas in the back and on the west side of the garage, of which there are plenty. Otherwise I will wait until just after the next rain.

I started reading Big Lake Scandal last night and continued with it this evening.  It’s the 5th and latest book in the Big Lake murder mystery series by full-time RVer Nick Russell.  Nick is a good writer, but he and his wife, Terry, are personal acquaintances, which makes reading his books that much more fun.

 

2014/09/01 (M) A Day To Labor

Leave a reply

One of the odd things about being “retired” is that holidays, like weekends, do not have the same significance they had when we were employed full time.  We no longer have “3-day weekends.”  We also do not have a tradition in our family of gathering on the summer holidays, so those days tend to blend into the days around them.  If not for our Saturday morning ham radio breakfast and the Sunday morning Howell Farmers Market we probably would not know what day of the week it was.

Knowing that today was Labor Day, Linda prepared vegan cinnamon rolls yesterday and baked them first thing this morning.  This was the first time she has made these and they were a real treat. Vegan, yes; whole plant-based food, not exactly.  These will be a rare treat for us.

As has been my pattern for the last few weeks, I sanded and touched up drywall first thing after breakfast.  Most of the drywall compound was finally smooth enough that I felt it was ready to prime.  I discovered that I was out of primer, so I went to Lowe’s to get some and picked up a few other things while I was there.  It was very humid today, which tends to slow the drying of paint, but primer is thinner than paint and gets absorbed into the paper drywall covering   I was hopeful that I might get a first coat of paint applied this evening.

Mike (W8XH) sent an e-mail Saturday evening to the members of the SLAARC announcing the availability of the new WordPress website and indicating that they would each be receiving a unique username and password from me in the next few days.  I wanted to wait at least 24 hours before I started creating users.  That waiting period had passed, so today I parked myself in front of my computer and registered users.

Part of the registration process required me to create a username.  That was easy for a ham radio club as (almost) everyone has an FCC call sign.  It also required a valid/unique e-mail address.  When I created an account an e-mail, with their username and a randomly generated password, got sent to the e-mail address I entered.  The e-mail also contained instructions on how to get to the website, how to login, and how to change their password.  I finished creating the last user account around 9 PM, but I did not work on this between 5 PM and 8 PM.

The vegan cinnamon rolls made for a filing and somewhat higher calorie breakfast, so we skipped lunch today and had an early dinner.  I had requested a picnic type of meal to celebrate the end of the summer tourist season, and Linda fixed a nice one.  We had vegan potato salad, corn-on-the-cob, and pan-grilled tofu slices with BBQ sauce and caramelized onions served open-faced on some of the Italian bread she made for dinner on Saturday.  Dessert was watermelon balls.  And the wonderful thing is that I am maintaining a good weight.  Eating well and eating healthy are not mutually exclusive.  However, like low-fat and fat-free foods, and then gluten-free foods, the processed food industry has discovered a “market” for foods that are free of animal products.  That, however, does not mean they are free of unpronounceable chemicals or excessive amounts of sugar and salt.  There is a growing amount of vegan junk food available in the marketplace.

We spent a little time after dinner on the back deck watching wildlife as a storm front approached from the west.  As the wind kicked up we lost our AT&T DSL connection and then our phone went out, exhibiting the same behavior we have had throughout most of August.  I shut down my computer and changed back into my work clothes to do some painting.  I put a coat of paint on the east wall of the garage and both the inside and outside of the utility closet.  It started raining really hard so I had to close the garage door, which cut down on my light, but eventually the rain let up and I was able to open the garage doors again.  The inside of the utility closet may need another coat, but I think that most of the outside of the closet, and the east wall of the garage, may be done.  That means I can finally mount the thermostat for the garage furnace and put cover plates back on switches and outlets.

I am still working on the outside of the south wall of the utility closet (with the door).  I am using drywall compound to create a smooth transition at the hinge edge of the door to correct for a carpentry error I made when installing the door much earlier in the project.  The transition will make it possible for me to install trim around the door, but I have to build up the transition in thin, tapered layers, allow it to dry, sand it smooth, and repeat the process over, and over, and over.  Ditto for the west wall of the library, which is the other side of the east wall of the garage, where I am building up a slightly recessed area where the opening was for the old window A-C unit so it will blend in with the surrounding wall surface.

20140827 (W) HVAC and Dentistry

Leave a reply

The only thing these have in common (for me at least) is that they occurred on the same day.  Darryll and Alec were back this morning to continue working on our garage furnace and library HVAC project and I had a 2 PM dentist appointment to have them check if I had lost a piece of one of the abfractions they did back on June 17th.

Our dentist is in Dearborn some 50 miles to our southeast, so I try to leave 90 minutes for travel.  I got there ahead of time and they got me in about 15 minutes early.  It was a quick appointment but I was glad I went.  The hard piece of material I crunched while brushing my teeth a few weeks ago was, indeed, the abfraction material from the upper outside of tooth #11.  They replaced it under warranty and I was back on the road by 2:30 PM, which allowed me to make the trip back towards home somewhat ahead of the afternoon traffic rush.

These mushrooms appeared in the yard a few days ago as round balls and then opened up.

These mushrooms appeared in the yard a few days ago as round balls and then opened up.

I needed a saddle connector and Linda needed some “power greens” for our dinner salad so I exited I-96 at Grand River Avenue and headed towards Brighton.  There is a Home Depot right there, but they only had the 3/8ths saddle connectors in bags of five.  I only needed one, which I knew I could get at Lowe’s in Howell.  Traffic headed back towards Howell on Grand River was badly congested so I used a back route, taking Challis Road to Chilson Road to Latson Road.  The Lowe’s and Meijer’s are on opposite sides of Grand River Avenue at Latson Road.

By the time I got home Darryll and Alec had left.  Darryll had indicated they would knock off early and that he would be back next week to finish up.  While they were here they set the library A-C compressor/condenser in place by the west wall of the garage and got the refrigerant lines run, the power cable routed, and the control cable run.  They also cut the openings for the two lower supply registers in the library, installed the through-wall duct work, and the register grills.  Darryll will be back during the latter half of next week to finish up.  That gives me plenty of time to finish drywall work.

Summer is coming to an end.  The parochial schools are already back in session and the public schools start on Tuesday next week.  Lots of folks are heading north for the upcoming holiday weekend which marks the end of the summer tourist season.  Fall colors have already appeared on a variety of trees in our part of the county and a few seem somewhat advanced.  Except for the last few days, it has been a cool, moist summer.

Early this morning I e-mailed Shelly from the AT&T Office of the President thanking her for calling us on Monday in response to our Michigan Public Service Commission complaint filing that morning, and for following up with her contact information by e-mail.  Our phone line is still noisy to the point of being useless, but we have not seen the dreaded “Check Tell Line” or “Line In Use” messages on our phone and the DSL has stayed connected as near as we can tell.  I am not aware, however, that AT&T has actually done anything yet to fix the problem.  They certainly have not communicated any such information to us  Unfortunately working on the SLAARC WP website and creating user accounts absolutely requires me to be reliably online, as does the Intro to Linux course I am (supposed to be) taking through edX, so these tasks may have to wait until our AT&T DSL connection has been solid for a while.

 

2014/08/25 (M) AT&T and the MPSC

Leave a reply

I was scheduled to participate in a meeting of the FMCA Education Committee at 4 PM today but it got rescheduled to Monday, September 8, same time.  That was a welcomed change of plans which allowed me to concentrate on our construction project.

Roese Construction, the contractor for Consumer’s Energy, is still working along our street.  The main gas lines are run.  They are now digging the connection trenches, fusing the sections of pipe together, and filling the trenches back in.  We heard them working at the west end of our property and walked down to see what they were doing and take a few photographs.  A large backhoe was just starting to fill a trench at the northwest corner of our yard where two pieces of main line were joined with a branch line going to the cul-du-sac to the west.  There was a lot of water in that trench and it looked like a (muddy) lap pool.  The surface of the water was only about two feet below the surface of the ground.  I asked the backhoe operator if that was ground water and he said it was.  The northwest corner of our property is a low spot that forms small ponds around many of the trees when it rains, and stays wet for a very long time even after the surface water disappears.

We spent the morning and afternoon sanding drywall compound and touching up a few spots.  While the compound was drying I worked on electrical tasks and Linda worked in the kitchen and did some weeding in the beds around the house.  Somewhere in the middle of all that we put all of the sections of the ham radio tower back on the middle deck, had lunch, and made a trip to Lowe’s for a light switch and various cover plates.  I also picked up an 18″ x 28″ sheet of 1/4″ thick Plexiglas to use as a temporary replacement for the fogged window in the bus when I finally get around to removing it to have it repaired.

Our AT&T phone and DSL service is worse than useless at the moment.  After three un-returned phone calls to both the technician (who gave us his number and said to call him directly if the problem re-occurred within 30 days) and the infrastructure manager for this area (whose name and number we got from the technician) we were fed up, so we filed a complaint with the Michigan Public Service Commission.  About four hours later we got a call from a women who claimed to be from the Office of the President of AT&T letting me know that she was in receipt of our commission filing and that she would be coordinating the “investigation and service repair process.”  The audio level was low and the noise on the line was high, so I could barely hear her and said so.  Apparently she heard the noise too, so at least she knew we were not making this up.  She e-mailed us shortly thereafter with her name and contact information.  That’s a start, but what we really want is the clean, reliable signal that we pay for.

There are things I can do, and need to do, at my computer that do not require me to be online, such as editing the rough drafts of blog posts and selecting/post-processing photographs.  The last post I uploaded to our blog was for August 1st, so I am once again almost four weeks behind.  I needed to finish processing the tree photos from last Thursday, put them in a Dropbox folder, and e-mail the link to Paul at Detroit Tree Recycling, but I did not get that done either.  When I wasn’t eating or driving back and forth to Lowe’s I was working in the garage.

Speaking of food, Linda made stuffed mushrooms for dinner and served them with a side of grilled asparagus.  Both were very tasty.  After dinner I gave the east wall of the garage a final sanding and then worked on the utility closet wall while Linda vacuumed up the dust.  I wiped down the wall with a barely damp sponge and applied a coat of Zinzer primer.  It should be dry enough to paint in the morning.

I drove back to Lowe’s to return a couple of incorrect cover plates I had purchased earlier in the day and get the correct ones.  I picked up another gallon of paint while I was there to make sure I had enough on hand for tomorrow.  On the way home I had a nice QSO (ham radio contact or chat) with Mike (W8XH).  Ham radio is fun and we have yet to get involved in making long distance (DX) contacts with folks all over the world on the HF (high frequency) bands.  Getting our tower up with some HF antennas on it will help a lot.

 

2014/08/23 (S) Square Waves

Leave a reply

We have so much to do at home and on the bus that we might have skipped the SLAARC (ham radio club) breakfast in South Lyon this morning, but I had agreed to meet Chuck at his shop (bus garage) at 10 AM in Novi and to bring Mike (W8XH) along with his oscilloscope to look at the tachometer signal, or lack thereof.  We had a nice chat with our ham radio friends, discussed having dinner in a week or so with Bruce and Linda, and then headed to Chuck’s shop.

We had two different opinions as to what signal we might find, if any, at the end of the wires that connect to Chuck’s tachometer.  Matt, from Bob’s Speedometer, told me that the signal to both the VDO tachometer and speedometer were variable frequency square waves at 3 to 5 volts peak and that the electronics in the gauge moved the needle in proportion to the frequency.  Mike (W8XH) had talked to Jim (N8KUE), who works in the research lab at Ford Motor Company, and Jim was of the opinion that the input to these gauges was a pulse width modulated signal.  With pulse-width modulation the frequency and amplitude of the waveform are constant but the width of the “pulse” (the “on time” of non-zero voltage) varies from zero to some maximum percentage of the half cycle, up to 100%.  If it is on for the entire half cycle it becomes a square wave.  The longer the pulse (on time percentage) the more energy is transmitted.  The gauge electronics can convert that to a needle position or run a motor faster or slower, such as might drive an odometer.

So which was it?  Well…neither.  What we saw was an alternating current signal that appeared to simply be an impulse (sudden spike in the voltage), one positive and one negative per cycle, with the frequency responding in direct proportion to the engine RPM.  The impulse had a rapid but noticeable decay time that appeared to me to exponential, but we did not have the wires connected to a load and that may have affected the signal. The voltage we were seeing appeared to be in 300 mV range, a far cry from the 3 – 5 volts we expected.

We loaded the cardboard in my car before going to breakfast, so when we were done at Chuck’s we headed directly to Recycle Livingston.  From there we went to pet Supplies Plus for some cat litter and then to Lowe’s for four more sheets of drywall (Sheetrock) and a large tub of better drywall compound.  After fighting with the back wall of the garage recently and having trouble with using the patching and repair compound yesterday, I wanted a drywall compound that would go on easier and smoother.  It could just be my technique, of course; I wasn’t that good at dry-walling 32 years ago, and feel like I have lost what little technique I once had.

Back home we unloaded everything, changed into our work clothes, and had lunch; grilled “cheese” sandwiches with tomatoes and dark leafy greens and fresh peaches, ripened to perfection.

While Linda sanded the drywall compound I applied yesterday I removed the panel from the library side of the opening for the old window A-C unit.  I insulated the cavity, cut and installed a new piece of drywall, and re-taped the seams.  I helped Linda finish the sanding, wiped off the dust with a wrung out sponge, and then applied another coat of drywall compound.  I then applied a first cost of “mud,” as drywall compound is commonly called, to the filler panel in the library.

In preparation for dry-walling the new utility closet we had to do some carpentry to box around the flue and gas pipe where they pass through the west wall.  We also had to box around the supply air duct where it passes above the utility closet door.  Finally, we added some backer boards along the edge of the platform by the west wall.  The purpose of all of this carpentry was to provide backing along all drywall edges so it will be supported and can be secured.  Our final task for the day was to trim a piece of 2×4 to block off the top of the wall cavity where the return air duct is connected next to the door between the library and the garage.

For dinner we had leftovers from Thursday:  Koshary and pita bread with vegan garlic “butter.”  Linda read somewhere recently that drier white wines are generally considered (by someone) to go better with Middle Eastern food, but we thought our 2009 Egri Merlot went quite well with dinner.  Of course, Koshary is an Egyptian dish, and so perhaps more Mediterranean than Middle Eastern.  All of that reminded me that there really are no rules about these things; drink what you like and enjoy life.

 

2014/08/20 (W) Like A Well-Oiled Clock

Leave a reply

Darryll and Alec (DCM Heating & Cooling) were back today to continue working on the garage and library HVAC project.  I was talking to them as they unloaded tools and materials when I got a call back from Paul Keech.

Paul has changed the name of his company from Paul’s Tree Service to Detroit Tree Recycling and is also running American Mulch.  As I was told yesterday he is trying to focus on tree removal, especially wood lots with multiple trees, rather than tree trimming.  Among other reasons, the trees he removes provides the raw material for his mulch business.  Also, the guy who did most of his climbing the last ten years has moved on to another job and it’s hard for Paul to run a business when he’s up in a tree, even with a cell phone.  I tried to describe the trimming and removal work we need done but in the end we agreed that I would take some photos, put them in a Dropbox folder, and e-mail him the link.  He also encouraged me to get a couple of quotes from some companies more local to our new location.

While I was talking to Paul, Darryll found a small leak in the reducer at the T-fitting behind the garage and tightened it.  The pipe out of this reducer will bring gas into the garage and was the last piece of pipe they worked on the last time they were here.  Alec reset the pressure to 12 PSI and it appears to be holding better than it has up to this point.

In the course of the day, they…

  • …finished setting the Library furnace/air-conditioner and connected the parts together.
  • …cut the hole for the return air register and installed the return air duct.
  • …ran the supply air ducting from the top of the unit along top of the ceiling, over the top of the utility closet door, and then angled it to run along east wall at the ceiling.  All of the duct outside the closet is insulated.  Two flexible ducts will come off the top and run through the attic to supply air through ceiling registers on the east end of the library.
  • …marked the location for the two registers that will be at the bottom of two rigid ducts running down the east garage wall to supply air to the library just above the baseboard heat radiators.
  • …removed the old library window A-C unit and covered the hole with cardboard.  We will have to patch the opening on both sides with drywall and paint it.
  • …shut off the propane to the old library wall-hung space heater, removed the unit, capped the line (iron pipe), turned the gas back on and checked for leaks.
  • …connected the double-walled flue pipe for the library furnace.
  • …connected the double-walled flue pipe for the garage furnace.
  • …ran the 1/2″ iron pipe for the gas supply to the garage furnace.

They will take care of the air-conditioner condenser/compressor installation on a subsequent visit.  In the meantime I need to install electrical junction boxes for the two furnaces, which must have switches located within three feet of each unit.  I also need to run new 12 AWG 2+g NM cable for old A-C condenser/compressor and repurpose the existing A-C condenser/compressor wiring as an outside 120 VAC / 15 Amp outlet.

We still needed to repair drywall in the library and upper east garage wall and install new drywall on the lower east wall of the garage and on the new utility closet walls.  The lower half of the east garage wall is the next thing I have to do as I need to have it done before he comes back to finish the duct work.

I got a call from Chuck Spera just before noon letting me know that he was headed to his shop to pick up his old VDO bus tachometer and take it to Bob’s Speedometer Service on Bergin Road.  Bergin is an east-west road about one mile north of our house.  Bob’s was over at Old US-23, less than five minutes away.  I met Chuck there at 12:30 PM and we met with Matt who handles their VDO instrument repairs.  He tested Chuck’s tach and pronounced it broken but probably repairable, so Chuck decided to leave it there.

Matt did confirm for us that both the tachometer and the speedometer take a square wave input signal in the 3 – 5 volt range with deflection of the needle proportional to the frequency of the waveform.  Presumably this same signal regulates the speed of a motor that drives the gears of the odometer.  I had discussed this very situation with Mike (W8XH) just last night and he is willing to bring his 100MHz 2-channel storage oscilloscope and help us look for and trace these signals if needed.  Once we have known good gauges installed knowing what waveform to look for will help greatly with troubleshooting should they still fail to indicate the appropriate information.

After we were done at Bob’s I headed over to the Meijer’s northeast of M-59 and US-23 to get a few things for Linda.  By the time I got home, Glen Williams of Tenor Clocks LLC had arrived to service our grandfather clock.  I “broke” it about a month ago by trying to wind it at just the wrong time and it has not chimed since then.  It has also never been oiled in the 11 years since we bought it and Glen told us on Saturday that it should be cleaned and oiled every 5 – 7 years.  (We saw Glen at the GLCC/CCO rally in Clio, Michigan this past Saturday when we were there.)  Glen took the mechanism out and examined it and said that nothing was broken.  Apparently it finally bound up the last time I wound it from lack of proper oiling.  He cleaned it, oiled it, and checked it for wear but did not see any.  He reassembled it, checked the operation and timing, and said it was running smoothly and keeping very accurate time “…like a well-oiled clock.”

Although my time on the computer today was limited, I managed to post my blog entry for August 1st and started selecting photos for other posts.  I updated the Technical page on the SLAARC website with a document on low band antennas for Field Day use, and added a link to an online Smith Chart Tutorial.  I then updated the online roster.  I am at the point where I need to generate WordPress user accounts for the club members so I looked more carefully at the WP-Members plug-in documentation to see if there was a way to have the website e-mail each member as I create their account.  It appears that there is, but it will take a little more work on my part to get that set up and working correctly.  As I was working on this our AT&T DSL line started dropping out; again.

Linda spent part of the day preparing food ahead in advance of having company tomorrow.  She held back some of the crushed red lentil soup for our dinner and served it alongside sandwiches.  While we were eating we noticed that the phone said “Line In Use.”  We knew we were not using it, but I picked up one of the handsets, pushed “Talk”, and got a very loud, very noisy busy signal.  We checked all of the phones to make sure there wasn’t a problem with one of them.  There wasn’t.  When I checked again the message said “Check Tel Line.”  That usually means we won’t have a dial tone when we push “Talk” and that was, indeed, the case.

Ken is the service technician that has been out twice to try to resolve the problem and he left his AT&T cell phone number in case we had recurring problems.  He also left his manager’s name and phone number.  I called and left a message for Ken and then called and left a message for his manager, making it very clear that Ken has been working hard to resolve our problem and we are happy with the service he is providing.  I also tried to convey that the service disruptions are interfering with our ability to do things online, like edit websites.  It’s bad enough that the data rate is so slow, but we depend on our “always on” DSL service to always be on.

We went to Lowe’s after dinner to buy a couple sheets of drywall.  We looked for special cover plates with a switch opening in one half and a round hole in the other, but did not find anything like that.  We stopped at Teeko’s on the way back and had Jeff roast two more pounds of half-caff blends for us; one Ethiopian Yirgacheffe and the other Seattle Blend.  He was still out of the Sweet Dreams decaf blend, which we have him mix 50-50 with the regular Seattle Blend to make Sweet Seattle Dreams, but he is supposed to be getting some in his shipment tomorrow.

Back home we unloaded the drywall, had some fresh strawberries for dessert, and read quietly for a while.  I’ve been reading the PDF version of the 2nd edition of The Mobile Internet Handbook and am done except for the glossary and the appendices.  It is over twice as many pages as the 1st edition and is the definitive resource on connectivity for RVers in particular.

 

2014/08/15 (F) On The Level

Leave a reply

I got dressed this morning for physical work, but ended up doing very little.  I worked at my desk most of the morning, including working through the first chapter of the Intro to Linux course on edX.  I came up from the basement to have lunch at 12:30 PM after which I moved my car out of the pull-through driveway.  I then started the bus and, with Linda’s assistance, backed it out of the pull-through driveway, drove it the short distance to our straight driveway (which ties into the other end of the pull-through driveway), pulled it up onto the concrete driveway as far as it could go, and parked it.  The concrete driveway runs uphill from the road to the garage and, not knowing how long it might be there, I lowered the front end and raised the back end; not enough to level it but enough to make it better.  Linda chocked the drive tires while I hooked up the electrical shore-power.  The front bay had gotten water in it from the recent rains so we opened all of the bays to let them air out while Linda soaked up as much water as she could with a couple of old towels.

Spreading 21AA road gravel to fix the driveway.

Spreading 21AA road gravel to fix the driveway.

I got out our 8′ step ladder and pole saw/lopper to prune some large (1 – 2 inch) dead branches that were hanging over the pull-through driveway where the rear end of the bus normally sits.  I no sooner started this work when Phil from Precision Grading showed up right on time with his dump truck, tracked front-loader, and rolling compactor attachment to repair the damage done to the pull-through driveway by the recent landscaping work.

Phil off-loaded the front-loader from the trailer and then disconnected the trailer from the dump truck.  He had a small load of 21AA road gravel (with lots of fines) that he dumped in two different spots in the pull-through driveway.  He then put the truck back in the street and set up his laser level to see just what he needed to do.  He used the front loader to move the gravel around and distribute it evenly and finished by back blading it with the bucket to level it.

Rolling and compacting the driveway.

Rolling and compacting the driveway.

Once he had the gravel the way he wanted it, he removed the bucket and attached the vibrating roller/compactor.  He went over the driveway several times, always making his final pass going backwards while pulling the roller to smooth out the tracks created by the machine’s drive treads.  The roller/compactor worked the fines down into the base and by the time he was done the driveway looked and felt tight; even better than last year when Phil did not yet have this attachment.  The machine also shook the entire house, especially the rear deck which is mostly supported by tall 6×6 and 4×4 posts.  He indicated that we did not need to wait for rain, or anything else, before putting the bus back in its spot, so after he left that is what we did.

But before Phil left, he used his laser level to check the grade in the back.  Although it does not appear to the naked eye to drop very much in the first 70 feet, the laser level indicated that there was a steady down slope over that distance with a total drop of over 1 foot.  He checked all the way to the edge of the cattails marsh, at which point the ground was down 4-5 feet from the deck.  The surface of the neighbor’s pond looks to be at least two feet lower from there.

The compacting roller really makes a difference.

The compacting roller really makes a difference.

There are several implications to this.  For one, it means the surface of the pond is well below our basement slab (6 – 7 feet) and at least 2 feet below the bottom of the footings for our house, so it is probably not the source of the water that runs into our sump.  It also means there is adequate grade to allow surface water to run off once the grass grows in (although it would be better if there was more grade than there currently is in the first 50 feet).  Equally important, the grade is more than adequate for a very effective French drain should we decide to have Phil pull up the existing drain lines and replace them.  Finally, having a hole dug at least 8 feet deep for the ham radio tower base should not pose a problem as the starting elevation is at least 6 feet above the basement slab.

With regards to the tower base, Phil suggested that I have the rebar cage, mounting bolts, and alignment structure built ahead of time and ready to go.  He could dig the hole first thing in the morning with his mini-excavator (up to 8’ deep) and figured it would only take an hour at most.  The assembled rebar could be positioned, plumbed, and secured in an hour or so, and the concrete could be delivered and poured in the late morning.  He indicated that spreading the work out over more time than that, especially letting the hole sit overnight, was not a good idea

Close up of the compacting roller attachment. This thing shook the whole house!

Close up of the compacting roller attachment. This thing shook the whole house!

We discussed how to get the concrete into the hole given its location about 40 feet northeast of the northeast corner of the house.  Our two options appear to be the little dump carts or a pumper.  The carts would have to drive up the east side of the house between the house and the septic tanks, but Phil thought that would be OK as long as they put down plywood to drive on.  He said a pumper truck would be very expensive but that a separate pump is available that can be towed to the job site.  With that equipment the concrete mixer truck would simply unload the concrete into the pumper, which would then pump it to the hole.  Both the truck and the pumper would be in the east end of our pull-through driveway.  Phil suggested that I call Carl Russell in Byron, Michigan as he is a good concrete guy and probably has a concrete pump.

After Phil left we reversed our earlier steps and moved the bus back into the pull-through driveway.  It rolled right up onto the level pad area and did not leave any noticeable tire tracks.  Nice.  We hooked up the “50 Amp” shorepower cable, turned off the chassis batteries, checked that all of the battery chargers were working, and shut/locked everything.

While Phil was working, Linda went to the Howell Library to return children’s books and came back with a card for the Howell Melon Festival.  The Festival started today and runs through Sunday.  She wanted to go walk around so we skipped dinner and headed out around 5 PM.  At the first turn in our road we encountered two workers from Roese Construction.  They were working on installing the natural gas main line down the street and said another crew would be coming along behind them in 1 – 2 weeks doing the branch runs up to the meters on the houses.

The Howell Melon Festival was just getting started when we got there but parking was already at a premium.  We parked a few blocks away in an empty church parking lot.  Some of the smaller side streets were already blocked off but Grand River Avenue and Michigan Avenue were both still open to traffic.  They will be closed tomorrow and Sunday and filled with vendor booths.

The weather was perfect and all of the downtown restaurants were very busy with lots of outside seating.  In the 16 months we have lived in the new house we have never really visited most of the downtown Howell merchants.  We went into Country Squire, a business that sells fireplace logs and inserts as well as outdoor cooking grills.  They had a couple of natural gas fireplace logs that were 99%+ efficient and did not require the flue to be open.  We thought they were a bit pricey but they were actually capable of heating a room.  We don’t use our existing propane logs because they are mostly decorative and require the flue damper to be open, which just wastes fuel and money.  The Country Squire also had a couple of natural gas grills that would mount to our deck and attach to our existing quick disconnect.

We walked through the food vendor area but did not see anything that interested us.  After walking past the starting gate for the Howell Melon Run we ended up at Uptown Coffee, on the northeast corner of Grand River and Main, where we had some brew and Sabra hummus with pretzel chips.  We started back towards our car and paused at the Old Courthouse long enough to hear the first number by the band.  They sounded good and not too loud.  We had our folding camp chairs in the car but decided to pass on the concert.

We stopped at Walmart on the way home to buy a microwave popcorn popper bowl and stock up on flavors of ICE brand sparkling flavored water.  Meijer’s sells a few flavors but Walmart has the broadest selection, including my two favorites (pineapple-coconut and blueberry-pomegranate).  Our final stop was at Lowe’s for a 100-pack of bright orange marker flags.  I will use these to mark the powerline that runs under the driveway to feed the RV outlet, the propane line to the house, the drain pipe from the corner of the house into the first septic tank, and the drain pipe that connects the outlet of the second septic tank to the beginning of the drain field.

It was a long day but a good one.  We watched another episode of Doc Martin and then called it a night.

 

2014/07/31 (W) Wrapping Up?

Leave a reply

We were tired and went to bed early last night.  Naturally, that meant we were up earlier than usual this morning.  Linda made her fabulous vegan blueberry pancakes to get us fueled up for a long day of work.  The landscapers were also here reasonably early and had a very productive day.  More on that later.

Our first task this morning was installing a switch controlled dual LED floodlight fixture on the back of the garage above and to the left of the door (when viewed from the outside).  The location was determined by the construction of the rear wall of the garage.  I measured and re-measured the location of the cable hole to make sure the surface mounted junction box ended up in the center (vertically) of one of the siding boards.  I drilled a 1/2″ hole through the back (north) wall of the garage just to the right of the back door (when viewed from inside the garage) and just below the top plate.  I ran a 14-2+g (NM) cable (that I had previously prepped and left in the wall cavity) through the hole in the wall and then through the hole in the back of the junction box.  This was the part of the north wall where I had to remove concrete backer board, a burned 2×4, and singed insulation, so the studs and back side of the exterior plywood sheathing were exposed and accessible.

We moved around to the outside and I caulked the hole around the wire, put a generous band of while caulk around the hole on the back of the junction box, and a half circle of caulk around the top back edge of the box and mounted it to the outside of the house with the center knockout centered over the hole in the wall.  I installed the dual LED light fixture and put a bead of caulk around the top half of the junction box where it met the fixture.  (The heads of the cheap machine screws that now come with electrical fixtures and plates strip very easily making it difficult to get a tight fit.)  I caulked the wire hole from the inside and then dressed and secured the cable.  I turned the circuit breaker on, and checked for proper operation of the switch and light fixture.  It was all good.  I like it when that happens.

Our next task was to install three round blue plastic junction boxes for bare bulb light fixtures; two for the garage attic and one for the garage end of the library attic.  I was originally going to install a switch near the top of the fold-down ladder to control the lights and run power to it from a new ceiling light fixture in the utility closet, but we came up with a better solution.

There was a three-gang electrical box in the east wall of the garage just inside the door from the library.  It had two switches installed and the cover plate had openings for a duplex outlet in the third position, but no device installed there.  We thought this would be a better place for the switch—as there was already power to the box—if we could get a wire through the wall from the attic to the box.  The drywall is missing from the lower half of the wall so we had good access to the underside of the box.  (The drywall was removed by the previous owner to repair the frozen hot water baseboard heat pipes.)  I checked in the attic and it looked like we had a good shot at making this work.  The icing on the cake was that we could install a switch with a pilot light that is designed to fit in a duplex outlet cover plate.  Not only would it be convenient, it would provide a visible indication that the lights were on.

I did the attic work while Linda took care of the garage end of this task, passing me parts and tools as needed and helping feed NM cable. We ran 14-2+g (120V, 15A) wire from the attic through the east wall to the existing outlet box.  I pulled the cable over to the location by the library attic, mounted the box, cut the cable, unsheathed it, stripped the wires, ran it into the box, and secured it to the truss.  I repeated that process with the end of the free cable.  The plastic light fixtures I bought very conveniently feature pass-through wiring terminals so all I had to do was hook up the cables, fasten the fixture to the box, and screw in the 100 W rugged service bulb.

I repeated this process for the next box/fixture which I positioned just to the west side of garage ridge 1/4 of the way in from the front (south) wall.  Finally, I repeated most of this process for the third and final (for now) box/fixture which I positioned on the east side of the ridge 1/4 of the way in from the back (north) wall.  Somewhere in the middle of all that we stopped for lunch.

With the attic lights installed I needed to pull the wire that supplied power to the outlets in the west half of the garage out of the rear/north wall and up into the attic.  Easier said than done.  The cable was originally part of the circuit that powers the outlets in the northeast wall of the garage (and now powers the new floodlights on the back wall) but I disconnected it a week ago knowing that I wanted to feed it from a separate breaker.  The cable went through a hole in the top plate and I discovered that the bottom cord of the gable truss had been set partially covering this hole with the cable pinched under it.  I cut the cable from above and ran it into a plastic switch box.  Linda was then able to pull the tail end loose from underneath.  I will run a new cable from the sub-panel to the junction box after I get more pressing work done.

On that note I also realized today that I do not have to get the cables for the new circuits through the top plates above the sub-panel, which was going to be difficult-to-impossible.  The sub-panel is surface mounted and I already planned to box around it.  With the supply air duct coming out of the new HVAC unit and running straight out along the ceiling above the utility closet door I will have 16 inches of clear ceiling space.  The sub-panel is about four inches deep so I will have about three inches of ceiling above the panel and in front of the top plates where I can run new cable into the attic.  Brilliant!

Our last attic task for today was to disconnect two telephone wires in the wall cavity to the right of the sub-panel, pull them up into the attic, reroute them, and reconnect them.  One of them turned out to be the main phone/data line coming into the house from the AT&T box at the southwest corner of the garage.  There was a telephone wall outlet to the right of the old sub-panel that this line ran to before continuing on to the rest of the house.  The wires are very small gage, are unshielded, and the cable is draped through the attic over multiple 120 VAC cables.  I need to replace this with a single run of much better (shielded) cable when I have time.  Perhaps we will get less static on the phone and faster Internet data transfer rates.  (Nah, probably not.  It will still be an AT&T landline.)

While I started working on re-wiring the three-gang box in the east garage wall, Linda made a run to Lowe’s to get a 32′ roll of 16″ x 3.5″ (R-13) insulation and a switch with a pilot light.  I got the box rewired, we energized the circuit, and everything worked.  Yippee!

The landscapers today consisted of Steve (the owner), Spencer (his nephew), and Tommy.  Steve used the excavator to place four large boulders on the sides of the new front steps.  That was the last work to be done in front that required the excavator so he used it to back blade (level off) and compact (with the bucket) the pull-through driveway.  He was not able to return it to its existing condition but did the best he could with the equipment he has.

He took time out to use his chain saw to cut down a dead pine tree, cut it up into 4′ lengths, and carry the pieces back to his truck with the excavator.  He then used it to fill/grade a large low spot just southwest of the garage.  This was the route they used to get the excavator to the back yard.  It was also where all of the construction debris was piled until yesterday, and the excavator really tore the ground up in that area over the last four weeks.

Spencer and Tommy worked in the back hand-grading the slopes beyond the retaining walls and the area that was trenched for the drain tiles.  They worked in a layer of good topsoil, spread grass seed, and covered it with straw.

Steve plans to lay the brick pavers for the front sidewalk tomorrow and have the whole project wrapped up by the end of the day.  It looked like they were on track to accomplish that until Spencer informed us that there was apparently a leak in the drain tile somewhere in “the valley.”  Leak was an understatement; we had an area at least 8′ x 12′ that had turned into a pond.

It appeared that the drain line for the sump pump was somehow discharging its water at this point rather than it flowing all the way down to the drains at the back of the yard.   Spencer dug up some of the line coming down the slope and found several holes on the top side, but it did make sense that these were the source of the problem.  Our guess is that that line, which is not one continuous piece of drain tile, has become disconnected at the valley floor allowing all of the water to escape at that point, and/or crushed, causing the water to back up through a connector (which is only designed for water to flow one way).  Fortunately we kept the original PVC discharge extension pipe from the sump pump outlet so we temporarily disconnected the buried drain line and reconnected the extension pipe.

Whatever the cause of the leak, we are sure it will be found and fixed, we’re just not sure that will happen by the end of the day tomorrow.  I had thought about “testing” the system by using a garden hose to put a significant volume of water into each of the drain lines.  As of now, I will definitely be doing that.

Our final task was insulating a section of the rear/north wall.  We got three of the four plus cavities filled and ran out of steam.  Besides, it was dinner time.  Linda made one of her “go-to” dishes; angel hair pasta with onions, garlic, mushrooms, sun-dried tomatoes, basil, and mixed baby greens lightly sautéed in olive oil.  This is a dish she can throw together from ingredients on hand without a recipe and it is always delicious.  We had a small glass of Leelanau Cellars Summer Sunset wine while she cooked and a small glass of Meiomi Pinot Noir with the dish.  No salad and no dessert; just a great pasta dish and nice wine.  I got cleaned up and we watched the first episode of season five of Doc Martin.  As we were drifting off to sleep we thought we heard the distant howl of a coyote.