Tag Archives: Isringhausen USA (Galesburg MI)

2015/06/25 (R) The Mouse

Brighton Honda called yesterday in the afternoon to get permission to do additional work on my car.  Since we plan to keep the car for a while, and then perhaps give it to our son, it was the kind of work that needed to be done regardless of the costs.  They called back later to indicate that they would not have it aligned before closing time.  That was fine with us as it would have been inconvenient to impossible for us to get there by 6 PM to pick it up.  Linda told them to call in the morning when it was ready.

The top of the 40-foot tower from the WNW showing all of the antennas and the pulley with the haul rope.  The weather had definitely deteriorated from the day before.

The top of the 40-foot tower from the WNW showing all of the antennas and the pulley with the haul rope. The weather had definitely deteriorated from the day before.

It is amazing how attuned we become to routine sounds and how sensitive we are to non-routine ones, even (especially?) while sleeping.  So it was last night that I was suddenly aware that one of our cats was making a repetitive sound that was unusual.  I turned on my flashlight, hoping to not disturb Linda, and got out of bed.  Both cats were hunched down on the floor on Linda’s side of the bed with Jasper in front.  He was the one responsible for the sound and the reason was next to his head and about 3 inches away; a little dark gray mouse.

My first thought when I see one or both of the cats with a mouse next to them rather than in their mouth is that it is dead but that was not the case.  This mouse was alive and apparently not injured.  I have seen this behavior before in which the mouse basically “plays dead” and the cats leave it alone but watch it carefully.  Mice seem to know that cats are triggered by movement and that if they sit very still the cats just sit there and guard them.  It was 4:30 AM and I was not fully awake so I do not recall the exact sequence of events, but the mouse somehow ended up in our master bathroom.   I do not recall what I did with the cats but I think I went and got a box with high sides and tried to get the mouse to go in it and it made a run for it towards the bathroom.  Linda was awake by this point so she got a towel for me.  I went in the bathroom and used the towel to block the gap under the door and prevent the little critter from getting back into the bedroom while I tried to get it into the box.  I was unsuccessful and it managed to find a place to hide in the hot water baseboard radiator.

Linda got one of the live traps we recently purchased and baited it with the recommended saltine and peanut butter.  We set the trap near the radiator, turned out the bathroom light, shut the door, and tried to plug the gap with the towel from the outside, figuring we would deal with the mouse in the morning.  Juniper kept pawing at the towel and pulling it back from the door so we put both cats out of the bedroom and shut the door.  They found that confusing as they sleep with us and generally have the run of the house.  One or both of them pawed at the door meowing to get back in for quite a while.  It wasn’t the best night’s sleep we have had and the timing was unfortunate given the hard day of tower work.

Brighton Honda called at 8:01 AM to let us know the car was ready.  Hello, I’m awake now!  I checked on the mouse and it was now safely tucked away on top of the radiator fins inside the housing where neither the cats nor I could get to it.  We decided to leave the live trap in place, sealed the gap under the door, and kept the bedroom door shut to keep the cats out.

I had planned to drive to Isringhausen’s U.S. headquarters in Galesburg, Michigan today but first we had to get my car.  As long as we were headed that way we decided to go to the Brighton Panera for coffee, but had toast and juice for breakfast at home before we left.

The 100,000 mile service is extensive and includes changing the spark plugs.  Beyond the routine service items the Element needed a new ball joint and tie rod and had a stuck brake caliper pin that had to be repaired.  Given the front end work I also had them align it.  Butch and I rebuilt the front brakes last year so I was surprised that there was an issue with them, but the car has been towed and driven in some harsh environments since then so that may have been a factor.

The Panera at Grand River Avenue and I-96 is not one of our favorites.  More often than not we end up with coffee grounds in our cups and the bathrooms are not maintained as they should be.  Today was not the first time we have been to this location that the men’s restroom was out of toilet paper.  It is also often freezing cold inside the restaurant and today was no exception.  The weather was overcast and a bit gloomy but the outside temperature, while not warm, was much more comfortable than inside.  We were also unable to connect to their Wi-Fi signal, which is generally useable.  That’s pretty basic stuff to not be able to get right and falls squarely on local management in my opinion.

While we drank our coffee I called Rick Short at ISRI to make sure he would be in but I got his voice mail again.  I asked for a call back but never got one so I did not make the trip to Galesburg.  Apparently they have better things to do than be of assistance to me.  I only want to buy one chair, not a fleet of chairs, so I understand my relative unimportance, but I don’t like it just the same.  We decided to spend the day at home completing the work from yesterday, which had made a mess throughout the house.

One of the things we needed to do was register our cellular booster system.  Given that it is a five band device I was not clear on whether we had to register it only with Verizon or with all of the carriers.  I called the company we bought it from, Cellular Solutions, and talked to Judy who said we only had to register it with the carriers we personally use.  For us that is Verizon Wireless.  Registration was via the Verizon Website and was simple enough.  It did, however, require me to log in to our My Verizon account and navigate through a couple of screens to a page where we could enter the information from the label on the box.  The serial number was on two peel off tags, so one of those went on the booster and the other one went in the manual.

With the unit registered I turned the power switch on and watched the ‘Alert’ lights all go solid yellow.  As I mentioned in yesterday’s post solid yellow lights are not described anywhere in the manual.  I called Cellular Solutions back and said I had a technical support question.  The woman on the phone took my name and number and said someone would call me back.

Since I was apparently taking care of phone chores I decided to call Universal Towers and inquire about their B-30 base.  The woman who answered the phone never gave her name but was able to answer some questions.  She indicated that their base might or might not be compatible with older Heights Tower products, depending on exactly which product I had, and that I would have to talk to the owner, Bill, who wasn’t there at the moment.  She did know that the outside-to-outside measurement of the legs on a B-30 base was 30 inches and the base cost $290.  She also told me that the larger bases, like the B-30, consisted only of the three rods with the mounting yokes on top; the three rods were not otherwise connected together in any way.  She also confirmed that the ‘U’ shaped yokes at the top of the base rods were welded on and not adjustable.  The normal installation procedure involved connecting them to the bottom of the legs of the first section of the tower, setting them in the hole as the concrete is poured, and adjusting them by moving them around until the legs of the tower were plumb.  That sounded to me like a process where a lot could go wrong and not be repairable.

I pulled a 75 ohm coax out of the ceiling of the basement yesterday.  We laid it out in the basement to see how long it was and it looked to be at least 60 feet.  Linda suggested we test it before running it through the basement ceiling which was a very sensible idea.  I unplugged the power adapter for the TV amplifier power inserter, detached the coax that feeds the TV in the bedroom, attached the downstairs cable, and connected the other end to the basement TV set.  Linda set up the TV for Antenna input, did an All Channels scan, and got the same stations we got yesterday, minus a couple.

In spite of what appeared to be acceptable performance I decided I wanted a new coax cable and Linda wanted to return three of the ropes I bought at Lowe’s but never used.  She found the receipt and we went to Lowe’s.  They had a good quality RG-6 quad-shield coax (75 ohm) in various lengths including 50 feet, which is what I needed.  At the register I decided to buy two more 40 pound bags of solar salt.  I am not an impulse shopper as a rule but their supply of Morton Solar Salt was very low and stocking up seemed like a good idea.

We stopped at Teeko’s to order coffee.  Mary took our order and rang it up; one pound each of the three different half-caff blends that have become our standard.  We took note of the fact that the Bennigan’s restaurant building on the northwest corner of Grand River Avenue and Latson Road was gone and a sign said a Panera would be coming soon to that location.  We didn’t say anything to Mary, but that cannot be good news for Teeko’s.  We will continue to buy our custom roasted beans at Teeko’s as long as they are open but it is going to be difficult for them to compete with a $2.25 cup of bottomless coffee, free Wi-Fi, a restaurant, a bakery, drive through service, and ample parking with great access to I-96.

When we got home I checked the live trap in our master bathroom and we had captured the mouse.  We took the trap to the northeast corner of the property, towards our neighbor’s pond, and set it free.  It did not want to leave the trap and I had to encourage it to go.  Once it hit the ground, however, it scampered away looking for a place to hide.

We then worked on running the new coax from the basement TV to the sump pump room above the suspended ceiling.  I disconnected the power inserter for the amplifier and disconnected the old coax we had tested earlier.  I notched a ceiling panel at the corner of a boxed support column behind the basement TV to allow the ceiling tile to go back into place around the coax.  We then installed one of the wire channels to contain and hide the coax from the ceiling down to the TV set and connected it to the back of the set.

In the sump pump room I attached the coax from the cable entry box (CEB) to the input of the new 1-to-2 signal splitter.  I attached the coax for the bedroom TV to one output from the splitter and the coax we just ran to the other output.  I mounted the splitter on the wall of the sump pump room and secured the cable coming from the CEB to the ceiling.  I then plugged the power supply for the power inserter back in to an AC outlet.  Linda scanned for channels and verified that everything was working correctly.  We then installed the other wire channel alongside the trim on the bedroom doorwall to route and hide the cable coming up from the basement.

I continued to fuss with the cell phone booster gain settings.  We had not gotten the promised return phone call from Cellular Solutions Technical Support so I called them.  I got Judy again and explained what I was seeing with the solid yellow lights.  She checked with her tech support people and they said the manufacturer (SureCall) told them the solid yellow was the same as the blinking yellow; that the booster was adjusting the gain and it was “normal.”  The manual says that normal is when the light is off, so I’m not sure I buy this explanation, but based on that I left the booster turned on.

With all of that done we started cleaning up the tools and materials we had scattered over two floors of the house.  I decided that was also a good time to start a load of laundry, although it was actually rather late in day for that.  I did three loads by the time I was done and it was sometime after 10:30 PM before the last load was dry.  I needed to be up at 7 AM to be at breakfast in South Lyon at 8 AM as our SLAARC group would start setting up for the ARRL Field Day event at 9 AM.

 

2015/06/23 (T) Grounded

As I wrote in yesterday’s post we did not turn off the lights last night until almost 1 AM because we were keeping a close eye on the weather moving across the lower portion of Michigan’s Lower Peninsula.  Although strong to severe storms were still forecast from 1 AM to 5 AM they either did materialize at our exact location or we slept through them.  We had the house closed up and the air-conditioning on, so that cut down the sound level of outside noises.

A cold front had pushed through by sun up and we woke to a cool morning with blue skies and noticeably lower humidity.  We did not have any trees, or even big limbs, come down and there was no damage to our brand new roof.  The forecast yesterday was threatening enough, however, that in the morning we took the potted plants, and as much of our outside lawn furniture as we could find room for, inside including our sun umbrella and trash cans.  I planned to be gone most of the day, and Linda was leaving mid-afternoon to go to dinner and a movie with Diane Rauch, so our first chore was to put all the lawn furniture, plants, and other outdoor stuff back outdoors.

This week is mostly being devoted to ham radio with the ARRL Field Day as the crowning event this weekend.  My specific focus for most of the week, however, has been the “communications tower” adjacent to the east wall of our house.  As described in previous posts we installed a cable entry box (CEB), mounted the cellular booster in the basement, mounted the inside cellular antenna, and ran coax cables.  The antennas will (hopefully) be mounted on the existing 40 foot tower tomorrow, cabled into the CEB, and cables run from there to devices inside the house.  With any luck by the end of the day tomorrow we will have decent cellular service inside the whole house, the ability to watch OTA TV programs on two different TV sets, and finally be able to connect one of our radios in the ham shack to an antenna.  Today, however, was planned to mostly address other things.

I had an appointment with our dentist at 10:20 this morning and left at 9 AM.  I planned to stop at Chuck’s bus garage and check that the key he lent me worked, but I needed gas for my car.  I did not have time for both and did not really have a choice; I would have to check the key some other time.  I ordered two cables yesterday from Scott (AC8IL) at Adams Electronics.  Later in the evening I was unsure if I had specified the connectors correctly so I called and left a message.  I called again this morning to make sure the message got through.  It did, and my original connector specifications were correct.

I arrived at the dentist’s office about 10 minutes before my appointment time.  I called Rick Short at Isringhausen USA to make sure he was going to be in before I drove two hours to Galesburg, Michigan after my dentist appointment.  I got his voice mail a left a message.  “ISRI” makes very high tech air suspension driver’s seats that are used as original equipment in motorcoaches, semi-tractors, heavy equipment, and locomotives.  I would really like one for our bus, but it is not proving easy to get.

Dr. Steve and his assistant, Leslie, made molds of my upper and lower teeth and a bite impression.  The molds will be used to make a mouth guard that I can wear while I sleep.  Dr. Steve has a strong suspicion that I am clenching my teeth and the mouth guard will reduce or eliminate the irritation it causes.  I will have to ask if I can wear it during the day too as I am occasionally aware of clenching my teeth while I awake.

I had not heard back from Rick by the end of my appointment so I called the main number at ISRI and talked to the receptionist.  It turned out that Rick was not in today and she transferred me to Jeff Woodworth.  Jeff was willing to meet with me but thought it would be a better use of my time to wait until Rick was available.  My next opportunity to drive to Galesburg will be Thursday and I will likely go as the ISRI seat is holding up our ordering of Flexsteel seats through Coach Supply Direct.

I stopped for coffee and then re-routed for Chuck’s bus garage in Novi.  The key to the garage worked perfectly.  I called Linda to let her know about the change in plans and headed for home.  There is too much to do at the moment to waste much time so I installed the #4 AWG bare copper ground wire I bought yesterday at Lowe’s.  I mounted an offset copper wire lug using the center support stud for the copper back plane in the CEB.  I replaced one of the plastic hole plugs with a rubber plug with a small hole in the center.  The hole I chose in the bottom of the CEB allowed the ground wire to come straight up into the lug.

Another view of the cable entry box on the east end of the house by the 40-foot tower.

Another view of the cable entry box on the east end of the house by the 40-foot tower showing the bare copper ground wire that runs to the ground rod and then to one of the tower legs.

Outside the CEB I routed the ground wire around to the existing ground rod and secured it using the new clamp I bought yesterday.  There was an old ground wire connected from a clamp on the tower to the ground rod.  I removed that wire along with some coax and control wires that I had clipped when we removed the old satellite dish.  I then attached the new ground wire to the clamp on the tower.  While we were at it Linda trimmed back a small bush that was growing between the tower legs and I pulled leaves, grass and other stuff out from around the Day Lilies that we transplanted last year around the tower base.

With the CEB grounded we looked at how we might get a video cable up to the TV/monitor in our bedroom.  The wall where the TV is mounted has a hot water baseboard radiator that comes almost to the trim on the door wall.  That end of the radiator has a copper pipe that goes through the floor into the basement and it was easy to locate the pipe in the basement.  I determined that there was enough space behind the pipe to safely drill a hole but I had to drill it from the top side at an angle.  A 5/8″ wood boring drill bit created a hole just big enough for the molded F-connector on the end of the cable to pass through.

We fed the video coax cable above the suspended ceiling in the ham shack area to the location of the hole.  I then fed the cable up from the basement as Linda pulled it up into the bedroom.  We adjusted the amount of cable in the bedroom to allow the wall mounted TV set to move through its entire range of motion.  The other end of the cable was then routed into the sump pump room.

By the time we finished pulling this cable it was 3:30 PM and time for Linda to leave to pick up Diane.  They were headed to Royal Oak for dinner and a movie as the movie they wanted to see was only showing at the Royal Oak Main Theater.

While I was out during the morning Lynch Carpet had called to let us know our Armstrong vinyl tile was available for pickup so after Linda left I closed up the house and went to get it.  The 12 boxes of tiles, container of vinyl adhesive, and container of vinyl grout were all neatly arranged on a small pallet and tightly wrapped in shipping plastic.  Rather than break this down and load each thing individually they used a fork lift to set the pallet in the back of my Honda Element.  The rear suspension settled at least two inches when they transferred the full weight of the pallet to the floor of my car.

When I got back to the house I backed the car up to the garage.  I cut the shipping plastic loose and unloaded the tubs and boxes of tiles.  I put the pallet on the garage floor and then neatly stacked the boxes of tiles on it to keep them off the floor.  Each box contained 14 tiles measuring 16″ by 16″ for a total area of 24.89 square feet.  The Armstrong Alterna tiles are a “luxury vinyl” product, and are about 1/8″ thick.  Even so, the boxes were heavier than I expected so I decided to weigh one.  It tipped the scale at just under 42 pounds.  That meant the entire pallet weighed close to 500 pounds, and, ignoring the weight of the cardboard box, that is about 3 pounds per tile.

When I drew out the design I determined that I would need 158 tiles, some of which would be partial.  Figuring conservatively at 150 full tiles equivalent, and ignoring the weight of the underlayment, adhesive, and grout, the floor tiles will weigh about 450 pounds.  I have no idea what the carpet and ceramic tile that I have removed weighed but the tiles were heavy.  I also have no idea what the furniture weighed that we have removed but also have no idea what the new furniture will weigh.  The intent was that the new floor and furniture would weigh less than old stuff but we will see.

I traded phone calls with my dad and we finally got to talk for a half hour starting at 4:30 PM.  He turned 90 this past Sunday.  Mike Fearer from Bid-Rite Concrete called at 6 PM and arrived about 10 minutes later to discuss the foundation for our 70 foot ham radio tower.  I had printed off a page from the Universal Tower website showing their tower base.  I also downloaded and printed their base and tower installation instructions.  I had a set of these to give to Mike so he would have some idea of what the project is about.  We looked at the proposed location for the tower and access for his dump cart.  We also talked about the base, a rebar cage, a form around the top of the hole to allow the concrete to be slightly above ground, and a jig to make sure the base is level and the tower is plumb.

He said he was interested in the job and would work with me and Phil Jarrell (the excavator) to get it done.  Rather than bid the job he would just do it for time and materials.  He also said the current price of concrete was about $100 per cubic yard.  We will need about six (6) cubic yards to fill the required 5′ x 5′ x 6′ (deep) hole.  He thought he might be available the middle of next week but I don’t think I could have everything pulled together that quickly.

After Mike left I went to Lowe’s and picked up five 40 pound bags of topsoil, a 1-in/2-out signal splitter (rated for 5 MHz to 2.4 GHz), and a plastic snap cover channel for hiding the video cable we ran up into the bedroom from the basement for the TV set.  I then went to the Meijer’s supermarket just across Grand River Avenue for soy creamer but they did not have what I was looking for.  As long as I was there I had a salad for dinner at the in-store Subway.

While I was sitting there I called Mike Sharpe (W8XH) to confirm that he was available tomorrow to help with the antenna installations on our 40 foot tower.  I mentioned that the only thing I lacked was a standoff with a pulley at the end of it for hoisting stuff up to me.  He suggested that something like that was essential and I agreed, so I headed back to Lowe’s to see what I could figure out.  What I ended up with was a three foot long 7/16-14 threaded rod, a pulley that had a closed eyelet on top (and was big enough for the 3/8ths rope I bought), some 7/16ths washers, and some 7/16-14 nuts.

When I got back to the house I unloaded the topsoil near the part of the east yard that needs to be filled in, took the other stuff inside, and then assembled the threaded rod pulley system.  I secured the pulley on one end of the rod using two of the nuts, one on either side of the eyelet.  I threaded a nut onto the other end, put on two washers, two nuts, two more washers, and another nut.  I ran the first two nuts, with two washers between them, part way down the rod.  I left the second pair of nuts, with washers between them, near the end of the rod.

I took the assembly out to the tower and adjusted the position and spacing of the two pairs of nuts and washers so they would bracket two of the horizontal tower members.  In use I will secure the rod to the tower at each pair of nuts/washers using plastic cable ties.  This arrangement will put the pulley at least 18″ from the tower which should be far enough out that we can hoist the DB8e OTA TV antenna to the top of the tower without it banging into the tower or hanging up on something.  This antenna is the largest thing we need to hoist up. The old TV antenna is considerably larger and heavier, but it is coming down via gravity.

There was a message on our answering machine from Linda’s sister, Sr. Marilyn, who lives in St. Louis.  She was listening to the news earlier today about the storms that went through our part of Michigan and wanted to make sure we were all OK.  By the time we finished talking it was dark and I was done working for the day.  Linda called shortly thereafter to let me know she was on her way home and I mentioned the call with Marilyn.

I finally opened the box with the vertical omnidirectional outside antenna for the cellular booster system and discovered that I should have opened it sooner.  The mounting bracket was designed to be mounted to a vertical surface, such as the side of a house, not a tube, such as a tower leg.  I did not want to postpone tomorrow’s tower work so I will have to get up early and figure out a way to adapt the existing bracket so I can mount the antenna to the top of the tower.

My initial thought was that an aluminum U-channel of the correct size might solve the problem very nicely.  I could drill two holes in the bottom of the “U” to match the two holes in the bracket.  I could then drill three pairs of holes through the sides of the channel.  The antenna would be bolted to the bottom of the channel.  With the open part of the channel held against a vertical tube I could secure it with three long plastic cable (zip) ties.  Conceptually it should work and be easy to fabricate, but will take time which I won’t have a lot of in the morning.  We have to get the two coax cables from Scotty (AC8IL), drop off my car at Brighton Honda for its 100,000 mile service, and be back in time to have the mount fabricated and all of the antennas and tools ready to go by 10:30 AM when Mike shows up.

Linda got home at 9:45 PM, earlier than she thought she would when she left.  She and Diane ate at Luigi’s and had a very nice meal.  They also enjoyed the movie.  We had a big day on tap for tomorrow and we asleep by 10:30 PM.

 

2015/06/15 (M) Cover Up

Linda was originally scheduled to go into the bakery today but it got rescheduled to tomorrow so we did not have to be up by any certain time other than to be ready for the delivery of our new roof shingles.  Apex Roofing is scheduled to put a new roof on our house this week, weather permitting, and assuming they can finish up jobs they had scheduled for last week when it rained so much.

The truck from Wimsatt Materials in Waterford showed up at 8 AM with our shingles but they were unable to deliver them.  They brought them on a boom truck that was too tall to fit under the phone lines across our driveway and there was nowhere else they could position the truck that would allow them to operate the boon.  They were on the phone with their dispatcher and I called Pat Davidson at Apex roofing to let him know what was going on.  The decision was that they would be back this afternoon with a conveyor truck which would fit under the wires and be able to get the bundles up to the roof.  Pat called back to let me know they would be starting in the morning around 7:30 AM.

Later in the day someone showed up in an Apex van with a large enclosed trailer.  We moved our cars and he backed it up in front of our single garage door.  Wimsatt did not return with shingles so they will presumably deliver them first thing tomorrow morning.  They will need to back into the driveway and position the truck in front of our double garage door but that is also where Apex plans to put their debris trailer.  The guy in the van also made it sound like there would be at least six cars/trucks here needing someplace to park.  It should be an interesting morning, especially given the overnight weather forecast which includes drenching rains and possible severe weather and flooding.  The forecast for the daylight hours, however, looks OK.

After the Wimsatt truck left we finished the last batch of granola for breakfast and then got busy with our chores and projects.  Linda spent part of the day at her desk working on the financials for our local ham radio club (SLAARC).  She also tried to contact PayPal to opt out of their upcoming RoboCall campaign but was not able to get through to a real person.

I settled into my office for the morning, dealing with e-mail but focusing on editing blog posts for the last seven days.  Kate got in touch with me to see if we wanted to see The Bikinis musical production at the Meadow Brooke Theatre this week.  Wednesday through Sunday is the final run.  She also forwarded an invitation to a former colleague’s retirement gathering in a couple of weeks.

We have an RV Critter Guard that seals around our 50 A electrical cord and water hose to keep “critters” from entering the coach via that access hole.  We lost our original foam insert when I forgot to remove it from the cable entrance hole in the floor of the bus utility bay and it fell (blew) out while we were driving.  I checked the RV Critter Guard website and my exact products were not listed.  I measured our existing tongue and groove plate and then contacted the company via their contact form and explained what I needed.  I got an e-mail back indicating that my product was custom made and asking me for one additional dimension from the plastic plate.  I got that measurement and e-mailed it to them and indicated that I wanted another plastic plate and two spilt foam inserts.  I expect to receive an e-mail tomorrow with the price.  Once I have that I will call them to place the order.

I have tried several times in the last two years to order products from EZ Connector but they have always had another question for me that required me to go check something and I have never managed to close the loop with them.  I’ve been on a roll the last couple of weeks and decided that today was the day to get this done.  The company is in California, so I called them during the afternoon (my time).  The woman I spoke to on the phone gave me some good information but suggested I e-mail Joe with my requirements.  Joe e-mailed me back and answered several questions but had another one for me.  I responded to that question and went on to something else while I await the prices.  Once I have the pricing I will have to call them and finalize the order.

I exchanged e-mails with Josh from Coach Supply Direct and got a series of revised quotes from him for our new RV furniture and window shades.  What I really need are the drawings that show the exact dimensions of each piece including the size of the base and the location of the pivot (swivel) point.  Apparently he is having difficulty getting these from Flexsteel.  I would also like to have these for the Lambright Comfort Chairs but we took our own measurements at Bradd and Hall.  The whole process of getting furniture is getting very frustrating.  I need to contact Mike at Suburban Seating regarding the ISRI 6860 and pick a day to drive to ISRI USA in Galesburg to look at fabrics.  While I am at it I should probably get a price from Prevost.

I finally got back to work in the bus this afternoon.  I shut off the auxiliary air compressor, closed the valve on the air manifold that supplies air to the toilet and other house accessories, and drained the water separator.  I then investigated what will be required to remove the toilet.

There is a shut off valve on the water line behind the toilet so I closed that.  The water line is attached to the toilet mechanism with a plastic connector with two wings and looked like I could undo it by hand.  The air line looked equally easy to disconnect but the drain looked a bit trickier.  It goes out the back of the toilet rather than through the floor.  There is a metal sleeve with band clamps at each end that connects the discharge pipe to the drain line.  Fortunately the band clamp screws are accessible.

The toilet is screwed to the floor with four Philips head screws.  The centers of the screw heads are threaded and there are plastic caps with posts that screw down into the mounting screws to conceal them.  With the water, air, and waste lines disconnected once I unscrew the base the toilet should slide forward and then we may have to lift it to get clear of the water line.  The trick to getting it back in will be to get the four mounting screws back in the exact same holes.

The humidity outside was near 100% and I did not feel like running the bus air conditioners so I did not remove the toilet today.  I need to get it out, however, to remove the last few pieces of ceramic tile from the bathroom floor.  Once it is out it will have to stay out until the new floor is installed.

I tried pulling on one of the window latch knobs on the fixed window across from the kitchen counter and was surprised by easily it moved the latch.  I did not pull it far enough to unlatch it but it appears that getting the window unlatched will be relatively easy.  Getting the frame open without damaging the frame seal, and getting it closed again so it is weather tight, may be slightly more challenging.

I used a chisel to try removing the thinset and mastic that was adhered to the plywood subfloor.  It came off better than I thought it would but it was a slow process.  In addition to being humid in the coach it was very warm as I have had to leave the roof vents closed with the fans off due to the rainy weather.  I removed enough thinset, however, to convince me that it is worth renting the power floor scraper from the Home Depot in Howell for a day and see how it works.

Late afternoon Linda worked in the kitchen making another batch of her fabulous granola and a black beans and rice dish for dinner.  She soaked two Hatch chilies, two Ancho chilies, and four Pequin chilies and used them in the bean dish.  I had a call from Pat Lintner before dinner to let me know that they took their Prevost to McMillers in Nappanee and were very pleased with work and the price.

I thought about driving to the Lowe’s in Howell after dinner to order the new Frigidaire refrigerator for the bus but it got too late to go.  We have decided to have it delivered to Chuck Spera’s shop in Novi.  We can pull it inside and he has a forklift, so hopefully that works out OK.

We were both tired and headed off to bed at 10 PM.  The weather radar showed a band of more intense rain setting up to our southwest and taking aim at us.  Linda fell asleep quickly but I was still up writing when the rains started around 11:15 PM.  We had the house closed up with the air conditioner running and a small fan for air movement so the sounds of the weather are not as noticeable as when we have the windows and doorwalls open.  I checked the radar again on Wundermap and it looked like we might be in for a long stretch of persistent rain unless the line drifted south just enough to miss us.  The strongest weather in the region stretched from Ft. Wayne, Indiana WSW to just south of Logansport, Indiana but there were lots of pockets of yellow with some orange on the screen over all of the southern half of Michigan’s lower peninsula and the northern half of Indiana.  It looked like it might be another restless night.

 

2015/06/03 (W) GLAMARAMA 2015 (Day 1)

Today was the opening day of the 2015 rally of the Family Motor Coach Association (FMCA) Great Lakes Area MotorCoach Association (GLAMA).  We were expecting three more arrivals from our Great Lakes Converted Coaches (GLCC) chapter but only two of them made it in before the 5 PM parking cutoff.  Jim and Lydia Marin, who parked next to us at Elkhart Campground on Sunday, arrived during the morning while Linda and I were out running errands.  Larry and Alma Baker arrived mid-afternoon.

Linda and I had our usual breakfast and then left around 8:30 AM.  Our first stop was Martin’s supermarket on US-33 northwest of downtown Goshen where Linda ordered the food for our chapter social tomorrow.  She and Karen Gerrie will pick up the deli trays, chips, pop, plates, napkins, and eating utensils tomorrow just before the social begins.

When we were done at Martin’s we continued up US-33 towards Elkhart, took CR-20 over to SR-19 and followed that north to W. Franklin Street where we headed west to the Elk Park Industrial Park and Paul’s Seating.  We met with Paul who was as helpful as he could be but it was basically a wasted trip.  He did not have a showroom, did not have additional information about the products shown on his website, and no longer carried any form of barrel chair.  His business appeared to mostly be recovering existing furniture, although later in the day we were looking at Pleasureway motorhomes (made in Elkhart) that featured furniture from Paul’s Seating.  It did not impress us as the highest quality RV furniture we have seen.

Paul suggested we look at MasterCraft for barrel chairs.  Linda pulled them up on the web browser on her phone.  They were in LaGrange, Indiana, which was quite a drive to the east on US-20, and did not have anything illustrated on their website that looked like the kind of chair we wanted/needed.  We went back down US-33 to Goshen, stopped along the way for a soft pretzel at Ben’s, and then returned to the fairgrounds.

I made phone calls to Isringhausen, Suburban Seating, Villa International, and Glastop RV Furniture.  I chatted with someone at Isri, Carlos at Suburban, Melanie at Villa (in Elkhart), and Peter from Glastop.  The calls to ISRI and Suburban were in connection with getting an ISRI 6800/6832/6860 bus driver seat.  The calls to Villa and Glastop were for barrel chairs.

We sat outside our coach for a while and chatted with Mike Dickson.  He and Kathy are in the Jayco Class C next to us.  We eventually got hungry and Linda made faux deli slice sandwiches for lunch.  By that point I was ready for a nap and slept for about two hours.  We had some of the seitan stroganoff for dinner around 5:30 PM.  I put on my nice GLCC shirt and at 6:05 PM we took the GLCC chapter flag over to Building A to line up for the opening ceremonies.  I thought I could handle the flag alone but we decided to have Linda help carry it.  She was wearing her Desert Bar T-shirt so she went back and changed into her GLCC shirt.

The opening ceremonies started at 6:30 PM.  After the presentation of the Canadian and American colors, the singing of both national anthems, the pledge of allegiance to the U.S. flag, and a very religious invocation, we had the parade of chapter flags.  That was followed by the introductions of a long list of FMCA dignitaries and announcements.  Fortunately it was all done by 7 PM.  There was a short break before the Frustrated Maestros started playing and we took that opportunity to return to our coach as did many of our other chapter members.  Several groups of us stood around and chatted until it got chilly and we all went inside.  The rest of the evening was spent in our coach using our iPads.