Tag Archives: grilled asparagus (vegan)

2015/05/27 (W) The Root of all Things

Leave a reply

Yesterday I used up the last of the coffee beans that Jeff at Teeko’s shipped to us in Quartzsite in late February so this morning I transferred the beans we had roasted last week into our airtight containers and started using them.  Grinding our own custom roasted coffee beans is how my mornings usually start and is just another small thing I like about being retired.

We rarely made coffee at home in the morning when we were employed outside the house.  It took too much time and made a mess that had to be cleaned up later, including the travel mug that we had to remember to rinse out at work and then bring home.  Besides, Linda got free unlimited coffee and tea at the office and I found it easier to stop at Panera and get a large coffee to go; half hazelnut and half decaf.  It was part of my morning routine that I found comforting and the cup was disposable when I was done.

I had a follow-up appointment and evaluation at the endodontist today, so I did not work in the bus this morning other than to take a few pictures of the old dinette corner, where I removed the mirrors yesterday, and the area under the bed, which I also worked on yesterday.

After morning coffee and breakfast I went to my office to work at my computer.  I off-loaded the pictures I just took, selected a few, processed them, and copied them to the folder for this blog.  I then downloaded and installed Adobe FlashPlayer in order to view the Gilbreath Upholstery Service website.  The download also installed a McAfee virus checker that I did not ask for or want and I don’t recall being given an option to opt-out.  I really dislike it when programs do things like that.  In fact, I think it should be illegal and companies who do it should be subject to heavy fines.  I tried to download the PDF catalog but Adobe Reader said it had an unrecoverable error.  Arrrgh!  I e-mailed them to request one that worked.  We will see if that results in anything.

I was responding to a few e-mails when Butch called.  He was trying to figure out the best way to connect up the eight L-16 6 VDC batteries he bought in Quartzsite to make a 24 VDC battery bank with a 12 VDC center tap.  Working only from verbal descriptions we finally ended up with the same diagram of a series-parallel interconnection scheme with equal electrical path lengths through all of the batteries.  The difference between series-parallel and parallel-series is not important when the batteries are operating correctly but each connection scheme is vulnerable to a different battery failure mode.  I happen to prefer the series-parallel scheme as I think it results in better battery charging, but that’s an often debated subject.  The equal path lengths through the batteries, however, is something that is worth accomplishing if at all possible.

By the time we were done talking I needed to leave for my endodontist appointment.  Dr. McWatters said the root canal they did on my upper right rear (tooth #4) last September looked good.  They tested the upper rear teeth on my left side but did not find any indication of a problem.  That would normally be good news, except that I had an intermittent problem in that area all winter so I know something is wrong and will eventually require attention, most likely when it is least convenient for me (middle of the night on a weekend).  But for now there is nothing more to do.

hen I got home I had a few pretzels and hummus and some red grapes and then got back to work at my desk.  I copied my blog post drafts for the 17th through the 26th from e-mails to Word and started editing them.  I took a break to have some tea and write while Linda cooked dinner.  She grilled two veggie burgers along with the rest of the asparagus we bought on Sunday and served the potato salad she made earlier in the day.  Most of the asparagus was mushy except for the tips which I attributed to the plants not the cook.  These were very large purple stalks, not the usual somewhat thinner green ones so maybe that had something to do with it.

After dinner I returned to my desk and finished editing all of my blog posts for May 10 through 26.  Somewhere in the middle of that work Phil Jarrell returned my phone call from yesterday.  We agreed that I will call him back after the GLAMARAMA Rally and he will bring his laser level and we will shoot some elevations.  With a little luck and a bit of perseverance we may get a gravel driveway connecting the 3rd (westernmost) culvert to our concrete driveway with a level spot for one or two guest RVs to boondock. We will also get a dozen tree stumps removed, get a French drain installed to remove water from the western end of the property, and get a hole dug for a ham radio tower foundation.  That last bit of digging will also require a rebar cage, hinged tower base, and coordination with a supplier that can pump concrete immediately after the hole is dug.

When I was done editing my blog posts I logged into our WordPress site, deleted 181 spam comments, and installed an update for our Fast Secure Contact Form plugin.  I started creating the post for May 10 but half way through the Chrome browser became non-responsive indicating that it might be out of memory.  That seemed unlikely, but I closed all of the program’s I had open, shut down my computer, and restarted it.  When I logged back in nothing was responding so I sat and waited until I was eventually able to do things.  The first thing I did was uninstall the McAfee Security Scan app that got installed along with the Adobe FlashPlayer earlier today.  I then proceeded to download three updates for Windows and MS Office, or tried to.

The three updates were only 27 MB total, but after 35 minutes they were only 53% done.  My guess was that the data rate on our AT&T “High Speed Internet” (DSL) connection had slowed to a barely usable trickle, perhaps because of all the rain we had the last few days, but whatever the cause it was almost midnight so I left it to finish at its own pace and went to bed.  I worked on this post and played a few games by which time it 12:45 AM so I got up, put on my robe, and went back to my office.  The download had finished and two of the three updates had installed.  The third one reported an error but Windows Update needed the computer to be restarted to finish the installation so that’s what I did.

Windows updates normally install during shutdown and finish installing on startup and that is precisely what happened this time as well.  I let the system startup completely (until the hard drive light was not on) and then downloaded, installed, and ran the latest version of CCleaner.  It downloaded much faster so maybe it was the Microsoft update server that was slow, or perhaps the McAfee app was causing the problem.

We had rain yesterday and more rain today, including some thunder.  The lights flickered a few times both days but the generator never came on.  If out Internet performance is still sluggish in the morning I will reset the AT&T gateway and see if that helps.  I also noticed that our home refrigerator was suddenly showing 45 degrees F instead of 40.  Linda had loaded it up with food yesterday, and added the potato salad today, but the temperature should not have changed by that much and should have returned to the 40 degree set point within a few hours.  Even adjusting the thermostat down did not rectify the problem over the course of the day so perhaps something else has changed, such as a blocked vent.  I will have to check for that tomorrow.  Hopefully the power blips did not blip some control circuit.  I think I will pull the fridge away from the wall and cycle the power.  We can vacuum off the back while it is out.  If it still won’t hold the temperature we want Linda might get a new refrigerator for the house sooner than expected, although a call to AAA Appliance Service Network in Howell might a more prudent first response.

2015/05/24 (N) Nuts to That

Leave a reply

We had our usual coffee and breakfast granola but made a more leisurely morning of it than normal.  We finally got dressed around 11 AM and headed to the Howell Farmers Market at 11:20 where we bought another bar of soap from Marjorie.  I got to pick this time and chose the ginger-grapefruit.  We bought the Eucalyptus soap two weeks ago and Marjorie suggested letting them air dry for two weeks before using them.  We will see how long the Eucalyptus bar lasts once we start using it and that will tell us how often we need to purchase from her to stay ahead of our usage, allowing for drying time.

We stopped at Lowe’s to return the “white” toilet seat and buy a “biscuit” colored one.  We looked at pipe wrenches but did not buy one.  I did by a 14 TPI, 6″ long blade for my Sawz-All that said it would cut metal up to 1/2″ thick.  I still hoped to get the nut off of the trailer ball on the lawn tractor without having to cut the threaded stud, but the blade was my backup plan.

We had a brief confab regarding the motorcoach refrigerator alcove and cabinet.  I found my small plumber’s toolbox and it had several pipe wrenches inside.  I took the largest one and checked to see if/how it would fit the trailer ball on the lawn tractor.  It opened more than wide enough and looked like it would snug down tight around the throat of the ball (between the ball and the hex flange base).  Linda kept the pipe wrench from slipping out of position on the ball while I used the torque wrench with the 3/4″ drive, 1-1/8″ socket to remove the nut.  It was still a bit of work but we got the ball off without cutting, cracking, or heating.  I then backed the lawn tractor up to the utility trailer and Linda connected the trailer yoke to the tractor tow plate.

Next we tackled the hall bathroom toilet seat replacement.  Once again we encountered nuts that would not come off.  This time the nuts were a hard plastic but the bolts were rusted and the nuts would not turn.  I eventually cut through the two plastic nuts with a utility knife and pried them apart allowing us to remove the old retaining bolts.  We installed the new seat/lid which came with its own special bolt and elongated plastic nut.  The nuts had special tips designed for 1/2″ sockets and engineered to break off when tightened to just the right point.  We had both nuts torqued down and broken off but the seat was slightly crooked so I had to loosen then, reposition the seat, and re-tighten them by feel.  What should have been a simple, short job ended up being a long and difficult one, in part because there was not a lot of room on the sides of the toilet bowl to get under here and work.  As we were cleaning up Linda noticed that the toilet tank was leaning slightly to the right relative to the base/bowl and thought we should adjust it.

I was already aware of the leaning tank, and the fact that it was not as tight as it should be.  The tank is held to the bowl by two bolts that go through the bottom of the tank and are sealed by gaskets under the heads.  I tried tightening the wing nut on the left bolt.  Even though it was rusty I was able to turn it, but the tank immediately started leaking from the bolt hole in the bottom.  We shut off the water and flushed the toilet to get most of the water out of the tank.  Linda held the left bolt head with a long flat blade screwdriver while I turned the wing nut on the underside of the bowl, first by hand and then with pliers.  I was careful not to over torque it and the tank was still a bit wobbly, but it was straighter and it did not leak when we refilled it.  We will keep an eye on it.  A leaky tank will result in water continuously running onto the floor and causing major damage of not detected quickly and stopped.

Linda cleaned up the bathroom while I put the tools away.  We then changed the primary whole house water filter.  The filter we use is the same 10″ length as a standard potable filter element but is about 5″ in diameter and has two micron ratings.  It’s a spun polypropylene media that is 50 microns at the large outer surface and 5 microns at the small inner surface.  In principle it filters better and longer than a single micron rating element by filtering out larger particles first and thus not clogging up the 5 micron material with large particles.  The same thing would be accomplished, of course, with two filters in series, or three, or four, each with progressively smaller micron ratings.

The Post-It note by the filter said we had last changed it on 11 November 2013.  If that was true it was way overdue to be replaced.  The element was completely black from outside to in so it had been in there longer than the fall of 2014 for sure.  We are starting to get some slime in the toilet tanks again and the water seems to have a slight black tinge, but that may have been due to the filter element needing to be changed.  I may need to have Adams Water Treatment come out again to discuss installing an iron filtration system.  Our drinking/cooking water still goes through a reverse osmosis system, so it is very pure.

Having accomplished several rather physical tasks I decide to sit in the living room and work on my blog posts for the last few days.  Linda made hot tea for us to enjoy while iPading, after which she reheated the leftover risotto and asparagus from last night’s dinner and we finished the open bottle of 2013 Egri Merlot.  After dinner I finally settled in to work on computer-based tasks.  I had a long list of things to do but did not get to most them.  I did manage to off-load recent photos of the bus interior from my camera to my computer, select a few to use in blog posts, and processed them.  I edited a few more blog posts but did not get them uploaded to our website.  I then dealt with e-mails and went to bed.

 

2014/08/25 (M) AT&T and the MPSC

Leave a reply

I was scheduled to participate in a meeting of the FMCA Education Committee at 4 PM today but it got rescheduled to Monday, September 8, same time.  That was a welcomed change of plans which allowed me to concentrate on our construction project.

Roese Construction, the contractor for Consumer’s Energy, is still working along our street.  The main gas lines are run.  They are now digging the connection trenches, fusing the sections of pipe together, and filling the trenches back in.  We heard them working at the west end of our property and walked down to see what they were doing and take a few photographs.  A large backhoe was just starting to fill a trench at the northwest corner of our yard where two pieces of main line were joined with a branch line going to the cul-du-sac to the west.  There was a lot of water in that trench and it looked like a (muddy) lap pool.  The surface of the water was only about two feet below the surface of the ground.  I asked the backhoe operator if that was ground water and he said it was.  The northwest corner of our property is a low spot that forms small ponds around many of the trees when it rains, and stays wet for a very long time even after the surface water disappears.

We spent the morning and afternoon sanding drywall compound and touching up a few spots.  While the compound was drying I worked on electrical tasks and Linda worked in the kitchen and did some weeding in the beds around the house.  Somewhere in the middle of all that we put all of the sections of the ham radio tower back on the middle deck, had lunch, and made a trip to Lowe’s for a light switch and various cover plates.  I also picked up an 18″ x 28″ sheet of 1/4″ thick Plexiglas to use as a temporary replacement for the fogged window in the bus when I finally get around to removing it to have it repaired.

Our AT&T phone and DSL service is worse than useless at the moment.  After three un-returned phone calls to both the technician (who gave us his number and said to call him directly if the problem re-occurred within 30 days) and the infrastructure manager for this area (whose name and number we got from the technician) we were fed up, so we filed a complaint with the Michigan Public Service Commission.  About four hours later we got a call from a women who claimed to be from the Office of the President of AT&T letting me know that she was in receipt of our commission filing and that she would be coordinating the “investigation and service repair process.”  The audio level was low and the noise on the line was high, so I could barely hear her and said so.  Apparently she heard the noise too, so at least she knew we were not making this up.  She e-mailed us shortly thereafter with her name and contact information.  That’s a start, but what we really want is the clean, reliable signal that we pay for.

There are things I can do, and need to do, at my computer that do not require me to be online, such as editing the rough drafts of blog posts and selecting/post-processing photographs.  The last post I uploaded to our blog was for August 1st, so I am once again almost four weeks behind.  I needed to finish processing the tree photos from last Thursday, put them in a Dropbox folder, and e-mail the link to Paul at Detroit Tree Recycling, but I did not get that done either.  When I wasn’t eating or driving back and forth to Lowe’s I was working in the garage.

Speaking of food, Linda made stuffed mushrooms for dinner and served them with a side of grilled asparagus.  Both were very tasty.  After dinner I gave the east wall of the garage a final sanding and then worked on the utility closet wall while Linda vacuumed up the dust.  I wiped down the wall with a barely damp sponge and applied a coat of Zinzer primer.  It should be dry enough to paint in the morning.

I drove back to Lowe’s to return a couple of incorrect cover plates I had purchased earlier in the day and get the correct ones.  I picked up another gallon of paint while I was there to make sure I had enough on hand for tomorrow.  On the way home I had a nice QSO (ham radio contact or chat) with Mike (W8XH).  Ham radio is fun and we have yet to get involved in making long distance (DX) contacts with folks all over the world on the HF (high frequency) bands.  Getting our tower up with some HF antennas on it will help a lot.