Tag Archives: Goshen IN

2015/06/02 (T) GLAMARAMA 2015 (Day 0)

We were up at 7 AM and had cinnamon toast for breakfast but did not have coffee.  We checked various routes to the Elkhart County 4-H Fairgrounds (EC4HFG) and searched online for information about any possible road construction problem areas but did not find anything that looked problematic.  By 8 AM we had started preparing the bus and car for travel.  Linda walked over to Curtis’s coach to say “so long for now” but all the shades were down so she sent him a text message that we were on our way.  We pulled out of our site at 8:15 AM.  I pulled up clear of other RVs and stopped to wipe off the passenger side mirror which was obscured with dew.  I am always surprised that I don’t notice things like that before we start to move.

We took CR-4 west to SR-19 and went south, crossing over the Indiana Toll Road, to CR-6.  There are times of the day that this intersection would be very busy but traffic was light this morning and I had no trouble getting into the correct turn lane and completing the turn.  CR-6 is a 4-lane road and moved along nicely all the way to CR-17 except for a short lane closure for local maintenance.  We turned south on CR-17, took it down to US-20, and headed east.  As I expected, this stretch of US-20 was still very much under construction with only one lane open in each direction and no wide loads over 11 feet permitted.  Traffic was more congested and slower but it moved along.  When we got to SR-15 we turned south and ran along nicely until we got to a construction zone that had the road down to one lane with flaggers.  We waited patiently and eventually got through the bottleneck.  We were routed through a short detour and then finally entered Goshen.  We followed the SR-15/US-33 Truck Route and found ourselves in another one lane construction zone with flaggers, and a train thrown in for good measure, but we eventually made it to our turn onto eastbound CR-34 (Monroe Street) and drove the final mile to Gate 5 of the EC4HFG.

We were directed to the staging area where we unhooked our car.  We were then led to the area reserved for our Great Lakes Converted Coaches Chapter and backed into our site.  The Laughing Raven Touring Co. bus was already parked in our area.  We saw this bus at Elkhart Campground while walking but did not realize it was headed to the rally.  The owner, Mark Lovegreen, is not a member of our chapter but wanted to park with other buses and we were glad to have him.  I reserved 12 parking spaces, the parking crew gave us 13, and I had a least one coach that was not going to show up so we had the space.  Also, Pat and Vicki Lintner got parked on hard surface nearby as the ground in our area was very soft when they arrived on Sunday.  In addition to being our chapters National Director Pat is the Senior VP of GLAMA would normally be parked elsewhere except that he likes to park with the chapter.

While Linda set up the interior and made coffee I hooked up the electrical power.  Our main 50 A circuit breaker did not want to set.  I finally pushed the lever hard enough to move it but did not like the way it sounded and did not get power to the coach.  I have indicator lights that told me there was power at the coach end of the shorepower cord but I verified that using my VOM.  I removed the cover from the disconnect box in our coach and verified that there was voltage present on both the L1and L2 bus but no voltage present on the output lugs of the circuit breaker.  Bummer.

Linda turned off the 30A supply circuit breaker and unplugged the cord.  I checked with the VOM that there was not voltage present and then unclamped the L1 and L2 load wires, removed them from the circuit breaker, and then removed the breaker from the box.  I tested it for continuity and with the lever in the “ON” position and one leg showed a short but the other leg showed an open.  That meant I should have had voltage coming through to our Progressive Industries EMS on one leg but I never did.  Regardless, we needed a new breaker as at least the one side had clearly failed.

The circuit breaker was a Square D QO style 2-pole 50A model.  I knew that Lowe’s carried QO breakers so Linda searched for the nearest store using her phone.  There was one on US-33 back towards Elkhart so Linda fixed a “to go” cup of coffee for me and I headed there.  They had a good selection of QO breakers including the 50A one that needed.  I looked briefly at refrigerators and noted that they had the Frigidaire model we are considering in white, black, and stainless steel.  Maybe we will drive up later to look at them.

I took a different route through Goshen to avoid the one lane construction zone.  Back at the coach I refilled my coffee and got to work.  As bus repairs go this one was pretty straightforward.  Getting the two load wires into the circuit breaker clamps was a bit tricky but I got them in.  The QO breakers snap onto a mounting rail at the bottom and then the contact fingers snap over two blades at the top.  All of that took a bit of pushing but I got it in.  I put the cover plate back on, reconnected the shorepower cord, turned on the supply breaker, and turned on the coach breaker.  We had power to the coach but it shut off.  I reset the breakers (turned them full off and then back on) and everything appeared to be fine and the power did not trip out after that.

With our power problem averted Linda walked over and got us registered and signed up for one of the few remaining time slots to work in the rally office.  She had volunteered to work registration but most of the time slots were already filled and the only thing left was Saturday morning.  Shortly after she returned to our parking area three more buses showed up:  Bill and Karen Gerrie, Mike and Kathy Dickson, and Joe and Mia Temples.  Next in were John and Paulette Lingafelter followed by Don and Sandra Moyer.  Late in the afternoon Scott and Tami Bruner arrived.  That only left a couple of coaches arriving tomorrow.

I borrowed a sledge hammer from Joe Temples and pounded three pieces of rebar into the ground to serve as supports for the clubs three flag holders.  A number of RVs around the rally site had the same design and I suspect that there was an article in the magazine, or something online, about how to build these.  They are very simple and inexpensive, can be taken apart for transporting, and rotate with changes in wind direction.  Our club as a USA flag, a Canadian flag, and a Chapter flag.

We all stood around in small, shifting groups talking about this and that.  I laid down around 2 PM and napped for about 90 minutes.  We are conveniently located to one of the bathroom/shower facilities so Linda took a shower there so as to not use up the good water in our tank.  By 6 PM most of our group had left to go out to dinner.  We ate around 6:30 PM, having a nice, light supper of cold chickpea salad on a bed of power greens.

A little before 7 PM we drove back to Lowe’s to look at refrigerators.  It turned out that the ones I saw were the 18 cu. ft. models not the 16 cu. ft. one we need/want.  The 18 cu. ft. model would fit in our alcove but take up the entire width leaving no space for a pull out pantry.  We looked at solar powered spotlights for illuminating the flags at night but at $18 each decided not to buy any as we needed at least three and would ultimately need the approval of the club to buy them.  We stopped at the Martin’s market on US-33 and picked up a deli tray brochure and a few grocery items.

Back at the rig there were lots of folks gathered in conversation.  Linda and Vicki went for a walk while I chatted with Mark (from Alaska) and Scott.  Scott and Tami recently had a new Whirlpool residential refrigerator installed in their bus so I went to see it.  It’s a very nice French door fridge with lower freezer drawer but is too tall for our alcove.  This is the style refrigerator Linda wanted but we could not find one sized to fit our space.  Bill Gerrie helped me get the U.S. and Canadian flags off of the holders.  Linda and Vicki returned just in time to help fold them properly.  With darkness came much cooler temperatures and everyone retreated to the warmth and comfort of their coaches.

Someone reminded us that Paul’s Seating in Elkhart was a good place to shop for furniture so Linda Googled it and found the website.  There were pictures of lots of chairs, including a barrel chair, but no information about dimensions, fabric options, or prices.  We will likely go to Martin’s in the morning and place a food order and then drive in to Elkhart and find Paul’s.  The critical path for our interior remodeling project goes directly through the selection of furniture and then through the refrigerator replacement so we are starting to feel some pressure about getting decisions made and orders placed.

 

2014/06/15 Family Time

We were parked in a fenced compound area next to the regular “campground” at the Elkhart County 4-H Fairgrounds.  The campground has gravel sites with 50A full hookups, and we were allowed/encouraged to use the sewer connections to dump our holding tanks before departing this morning.  We had checked out the campground last night and decided that it would be easier for us to pull around to the dump stations on the outer road than to maneuver into and out of one of the open campground sites, all of which were back-ins.

I have mentioned before what a nice facility this is.  Several of our GLCC members are from north central Indiana and explained to us that the fairground is as nice as it is because it is booked every week for most of the year, winter being the exception.  Elkhart is considered the center of the RV industry in the U.S., but the reality is that RV-related industry is located throughout north central Indiana, and a little bit of southern Michigan, with a few facilities in other parts of Indiana and Ohio.  There is also significant RV industry in California, Oregon, and Florida, and to a lesser extent in Pennsylvania and Alabama.  By “RV Industry” I am referring to manufacturing, not RV parks, resorts and campgrounds, or RV dealers and service facilities, which are obviously located all over the place.

We skipped breakfast and coffee, as we always do on travel days.  Linda prepared the inside for travel and then we visited for a while with our GLCC friends.  Around 9:00 AM I unplugged the electrical power, stowed the cord, turned on the chassis batteries, opened the air valve for the engine accessories, and fired up the engine.  I did not have any trouble getting out of our parking spot or the compound.  I drove over to the dump station, which can accommodate nine RVs at one time, and Linda followed in the car.  While the holding tanks were emptying we hooked up the car for towing.  With everything stowed and secured for travel we checked the toad controls and lights and were on our way, exiting the fairgrounds at 9:25 AM.

We followed the same route home that we used when we left the Escapade rally a month ago: CR-34 (Monroe St.) east to CR-29 north to IN-4 east to IN-13 north to US-20 east to I-69 north to I-96 east to M-59 east and finally a couple of miles of dirt roads to our house.  We stopped at the Travel America (T/A) truck stop on M-60 at I-69 to put biocide and Stanadyne diesel additive in the tank along with 75 gallons of diesel fuel.

We had just over 1/4 tank of fuel indicated on the fuel gauge when we pulled in to the T/A.  If the gauge is anywhere near accurate that was approximately 50 gallons of fuel, enough to travel another 200 miles and still have 15 – 20 gallons in the tank; more than enough to get us to the Mobil truck stop on I-96 about 25 miles before our house.  I wanted to use as much of the fuel in the tank as I could before adding more but did not want to risk running out or sucking sediment off the bottom and clogging the fuel filters.  In the end we decided it was safer to stop and add fuel while we still had the 1/4 tank.  The 75 gallons brought the fuel gauge up to 5/8ths, which is what I expected.  The fuel tank capacity is 235 gallons, but I assume the full mark on the gauge corresponds to 200 gallons.  That makes every 1/8 of a tank on the gauge correspond to 25 gallons.  We also presume that our average fuel economy, based on prior data, is 6 MPG which equates to 150 miles per 1/8 tank.

We did not fill the tank because the bus is going to be sitting for a while and we did not want to have all of that fuel onboard aging in the summer heat.  There is a reason, however, to keep the fuel tank as full as possible.  Most of the fuel that is pumped to the engine is used to cool the injectors and the DDEC engine computer and returned to the tank. The more fuel in the tank, the less frequently any particular molecule passes through the engine giving the fuel in the tank more time to dissipate the heat.

Our trip was easy and un-eventful other than the powered driver-side windshield shade quite working.  Add that to the list.  We got home by 1:30 PM which gave us time to unload food and a few essentials from the bus and take showers.  Since Linda spent Saturday morning preparing food, she only had minimal cooking to do for dinner.  Our son, daughter-in-law, and grand-daughter arrived at 3:30 PM and our daughter and son-in-law arrived at 4:00 PM.  Madeline had a cold, wasn’t feeling well, and had only had a short nap, but she was fine as long as she was busy.  This was a combination birthday and Father’s Day gathering, but mostly an excuse to gather our small, immediate family.  We had a lovely summer meal of potato salad, collard greens cole slaw, baked beans, and cheeseburgers with chocolate cupcakes (from a local bakery) and fresh strawberries for dessert.  All vegan, and all delicious.

Brendan, Shawna, and Madeline left shortly after dinner and Meghan and Chris left around 8:00 PM.  Although our morning departure and drive home had been quite routine and the family gathering had been relaxed and relatively easy, it all added up to a long day.  I started the download of an update to my Adobe Creative Cloud subscription that looked like it was going to take a while, so we skipped watching an Episode of Doc Martin and turned in for the night.

 

2014/05/11 (N) A Pre-Game Show

Linda received Mother’s Day wishes this morning from our daughter and son.  Modern communications technology has certainly changed the RV experience, making it possible to stay in contact with family and friends, and even work or conduct business from the road.  The Elkhart County 4-H Fairground has WiFi and the WiFi Ranger Company is sponsoring WiFi connectivity and the WiFi Cafe during Escapade.  Our friends were having difficulty staying connected from inside their metal hulled bus, but we found and locked onto a strong signal using our WiFi Ranger Mobile Ti and shared it with them.

Panorama of the Elkhart County 4-H Fairgrounds.

Panorama of the Elkhart County 4-H Fairgrounds.

Today was still early arrival–the Escapade doesn’t officially start until tomorrow–but many rigs were already here and more arrived during the day.  For a rally that had not yet started there was a lot of activity.  Escapees runs a very popular “RVers Boot Camp” as a pre-rally before every Escapade.  They also have their SmartWeigh program set up to weigh vehicles.  The Geeks On Tour (Jim and Chris Guld) were also running pre-rally workshops on technologies for travelers, including Windows 8, cell phones, Picasa, and blogging.  Yesterday and today were big setup days for the vendors and Escapade volunteers were busy setting up the registration area, seminar rooms, and other venues.

I got a call from Lou Petkus (K9LU) regarding photography during the Escapade.  Linda and I had previously volunteered to be part of an official SKP Photographers BOF Escapade photography team.  He picked us up in a golf cart around 9:00 AM and we drove back to Building A to meet up with Sue Spahn, the forth member of our team.  Since the advent of digital photography, Escapade has featured a slide show of the previous day’s events just ahead of the evening announcements, door prizes, and entertainment.  Kathy Carr, Escapees RV Club president, and her daughter-in-law, Angie Carr, have handled this in the past, but asked the SKP Photographers BOF if they would take responsibility for it this year.  It was fortuitous that the BOF agreed to do this as Kathy and Bud had to return to Texas for medical reasons.  Kay Peterson, SKP founder and SKP #1, returned to Texas with them.

Molly Pinner (Escapade Director) and Lou Petkus (head photographer).

Molly Pinner (Escapade Director) and Lou Petkus (head photographer).

The photography team met for about an hour, looked at the schedule of events for the week, and discussed the kind of photos we were after and the logistics of covering all of the activities and still having some time to participate.  Head and shoulders shots of smiling people were at the top of the list, of course.  We each got a flash drive to use for transferring our photos each day to Lou whose job it would be to assemble the daily slide show.

Registration opened at 10:00 AM so we took care of that and picked up our 54th Escapade polo shirts we had pre-ordered.  I got a few photos of the Registration area/process, coffee/donut area, and Escapade banners in the WiFi Cafe.  Kelly Hogan, the president of WiFi Ranger, had his magnificent Class D motorhome and matching communications trailer parked just outside the building and we were able to chat with him briefly to thank him personally for figuring out how to get our WFR-MTi working with the Williston Crossings RV Resort WiFi system this past winter.

There were signs of spring at the fairgrounds.

There were signs of spring at the fairgrounds.

Linda headed back to our coach to start working on a project with Butch and Fonda while I stopped at the AG building to take a few photos of the Geeks On Tour in action.  I also stopped by the RVers boot camp for some photos and then climbed the grandstand to take a panorama of the fairgrounds.  Back at our rig I shot another panorama of our row and then settled in to work on Butch and Fonda’s project until we had to meet with Lou again at 3:30 PM.  We found Lou and Val’s rig and then drove over to Sue’s rig in Lou’s golf cart.  While we were there Lou got Wayne to take a picture of the photography team.

We decided to go to dinner with Lou and Val and headed back down US-33 looking for Culver’s.  Linda and I were able to get nice salads there and split some French fries.  Lou started to drive us back to our site but we kept stopping for photo ops.  One of those opportunities was the Vendor pizza party/social.  We got our photos and visited briefly with folks we knew like Chris Guld of Geeks On Tour, Nick/Terry Russell of The Gypsy Journal, and Charles/Chris Yust of C &’C Marketing (our RV insurance agents).  Escapade directors Bob and Molly Pinner were there along with some other vendors that we recognized.  Molly invited us to stay, which we appreciated, but we are not RV vendors and this was their social.

Terry Russell, Chris Guld, and Nick Russell at the vendor/speaker social.

Terry Russell, Chris Guld, and Nick Russell at the vendor/speaker social.

The RV vendors are their own little community (sub-culture) within the larger community/sub-culture of RVing.  Many (most?) of them are full-time RVers who make their living traveling the RV rally and show circuits selling their goods and services.  As such they share experiences and perspectives that are different from those of us who just attend rallies and shows, especially those of us who are retired.  They are often at the same events and, even when they are competitors, frequently become good friends.

Wallce Lewis (Escapade Assistant Director), Dortha Hall (Escapade Coordinator), and Jim Guld (speaker) at the vendor/speaker social.

Wallce Lewis (Escapade Assistant Director), Dortha Hall (Escapade Coordinator), and Jim Guld (speaker) at the vendor/speaker social.

We finally got back to our coach where I downloaded photos from our Sony alpha 100 SLR camera to my laptop computer while Linda downloaded photos from her Samsung Galaxy S III smartphone to her laptop computer and then onto her SKP flash drive.  I used Microsoft Image Composite Editor (ICE) to process the two panoramas I had photographed and then transferred everything to my SKP supplied flash drive.  We walked over to Lou and Val’s 5th wheel and visited for a while as Lou downloaded the photos from the flash drives and took a quick look at them.

We decided to take the long way back to our coach by walking through some of the campground areas we had not yet visited.  Thick clouds had moved in and the skies to the west were getting ominously dark.  Several people stopped us to let us know that possibly severe storms were headed our way portending damaging hail and wind gusts of 70 MPH.  We shortened our walk and headed back to our rig where we found Butch outside talking on his cell phone.  We put up the two awnings we had down for sun shade and stowed our chairs and end table.  High wind and awnings don’t mix well.  Butch and I chatted until the mosquitoes got bad and then retreated to our respective buses for the evening.

Panorama of EC4HFG horse track infield parking area.

Panorama of EC4HFG horse track infield parking area.

It got into the low 80’s today and the humidity was up with the approaching weather, so the coach interior was in the upper 80’s.  We were watching the approaching storms on our weather apps and the weather/radar sub-channel out of Ft. Wayne, Indiana.  It was a fairly aggressive system but showed signs of dividing and going around us to the north and south.  The rain eventually started, forcing us to close our ceiling vents and narrow our window openings.  Serious lightning developed and the rain intensified to the point where we had to close the large entrance door window and reduce the awning window openings to about an inch.  With a forecast of continued rain overnight and a low of only 65 degrees F we knew it would not be the best night for sleeping.  Still, I love storms and enjoyed seeing/hearing nature’s power while I worked on blog posts for yesterday and today.

 

2014/05/10 (S) Goin To Goshen

We were up at 6 AM with our sights set on a 7:30 AM departure.  Most of the supplies that still needed to be loaded onto the bus were staged in the front vestibule, on the dining room table, or the bathroom counter.  It took several trips to get everything on board, including the cats, but it was an easy final loading process.  We are getting better at this with practice but it certainly helped having the bus parked with the front door opposite the front door of the house.

With everything on board we did the final preparations on the car and bus, pulled the shore power cord, and stowed it away.  We finished closing up the house, checked the lights on the coach and car (they were all working), arranged a few things on the interior, and were ready to roll.

The cats had already sought the safety of their travel locations under the front passenger seat even before I sat done in the driver’s seat.  The big Detroit lit right up and as soon as the oil pressure came up I engaged the high idle to make it easier to build the air pressure and switched the suspension to drive mode.  When the air dryer “sneezed” (purge valve opened) I turned off the high idle, pulled up the tag axle (to shorten the turning radius), put it in gear, and pulled out of our driveway.  It was 7:30 AM.  We made our way up to M-59 and headed west.

It was a chilly morning, though not as cold as earlier in the week when I reset the tire pressures and the TPMS sensors.  I quickly discovered that I had cold air coming in by my feet and shortly thereafter realized that I forgot to open the air supply to the louvers for the air-conditioner compressor compartment behind the front bumper.  When the louvers are open that compartment allows outside air to get into the bay under the driver’s seat and from there into the cockpit, especially at highway speeds.  The louvers require air pressure to close and prevent this air intrusion.  Rather than pull into a business or shopping center I decided to continue on to I-96 west and stop at the rest area at mile marker 112 which would allow an easy off/on just before reaching the Lansing area.

As I suspected, the air supply to the louvers was closed.  I usually shut off this circuit when parked to minimize leaks and auxiliary air pressure run time, but this is (obviously) not part of my mental “to do” list yet.  Every trip I say we need to create written checklists, one for departure and one for arrival, but we get busy and never follow through; at least we haven’t yet.

From the rest area we continued on I-96 west along the southern edge of Lansing, picked up I-69 at the southwest corner of town, and headed south towards Indiana.  It was a downhill run from there, or so it seemed, as the pyrometers were often near the bottom of the scale.  We exited onto US-6 and headed west towards Goshen, Indiana.  We picked this route so we could pick up US-33 north and come into the Goshen area from the southeast.  Our initial destination was a Walmart supercenter at the southeast corner of town on the east side of US-33.  Our plan was to meet up with Butch and Fonda who were driving in from Twelve Mile, Indiana.  From there we would have a short, but slow, drive up US-33 into the heart of Goshen and then east on Monroe Street to the Elkhart County 4-H Fairground.  It’s only a few miles but it is slow because of the heavy traffic that always seems to be present on this high density commercial/retail stretch of a two-lane US highway.

The Walmart "stables" on  US-33 southeast of Goshen, IN.

The Walmart “stables” on US-33 southeast of Goshen, IN.

We were in phone contact with Butch and Fonda so we knew their departure was delayed by business and bus issues.  We arrived somewhat ahead of our agreed rendezvous time, and decided to wait for them at the Walmart as long as we could without getting uncomfortable about the possibility of not getting to the fairground before the 2 PM arrival cutoff.   We did some shopping, had a bite of lunch, took some photographs, and played some games on our iPads while we waited.  The Walmart had a “stable” for the Amish buggies and it was full, with additional buggies tied up to the fence line.  You just don’t see that most places, but this is one of the things that is uniquely interesting about north central Indiana.  Butch and Fonda eventually got on the road and were making good progress but we decided around 1:15 PM to go on to the fairgrounds and try to meet up with them there.  That meant they would not have to stop at the Walmart and incur additional time delay.

Like most rallies, the Escapade requires rigs that want to park together to arrive together.  They also want the rigs identified in some way as being together.  For small groups (four or less) they wanted matching ribbons tied to the driver-side mirror.  For larger groups they wanted the arrival planned in advance with a placard in the window of each rig that identified the group and the rig number, 1 of n, 2 n, etc.  Although the Escapade did not provide a rendezvous area the arrival rate had slowed down by the time we pulled in and they allowed us to unhook our car and wait for our friends, who pulled in not more than 10 minutes behind us.

We had a nice chat with the parking crew while we waited and found out that some of them were members of the SKP Chapter 6 – Great Lakes, which covers Michigan.  We joined the Chapter at the 2010 Escapade at this very same fairground but have not yet made any of the rallies.  Chapter 6 is one of the oldest chapters in the Escapees RV a Club and will celebrate its 30th anniversary at a Labor Day rally this year.  The rally will be in Michigan and perhaps we will be able to finally attend.

We were directed to our adjacent parking spots on the east side of the infield of the horse track and got backed in with the assistance of the parking crew.  The fairground was well prepared for RVs on parts of the property that are not set up as permanent RV sites.  Electrical cables emerged from manhole covers and ran to outlet boxes on the ground and temporary water manifolds were placed alongside the power lines.  We only connected the shore power for now, having arrived with a full fresh water tank.  I dialed back the charger section of our Magnum 4024 inverter/charger to an AC input of 25 Amps before connecting the power through to the coach.  This limited the amount of power the charger section would use, ensuring that adequate power would be available for other essential coach functions such as the refrigerator, auxiliary air compressor, lights, coffee maker, and television sets.

We put out our patio awning to shade the passenger side of the coach from the afternoon sun and sat around for a while enjoying a snack of pretzels and almonds along with a tasty adult beverage (us, not them).  Linda and Fonda went for a walk while Butch and I fell asleep.  We woke up hungry and eventually decided to go out to dinner.  We took our car and since I was driving I had to pick the restaurant.  We ended up at a Chinese buffet and all ate too much.  We were surprised to see a lot of Amish buggies tied up outside the restaurant and even more surprised to see so many Amish inside enjoying the buffet.  I thought it was actually pretty cool, just unexpected.  By the time we got back to our buses we were satiated and tired.  We retired to our respective coaches for the evening.

 

2013_09_17 (Tue) To Goshen We Go

We awoke this morning to temperatures in the mid 40’s.  As we had no reason to rush we stayed under the covers a bit longer than usual.  Lazy mornings are always a source of consternation for our cats who, in spite of the obvious presence of food in their bowls, expect us to get up at the first sign we are awake and attend to their perceived need for fresh(er) food.

I turned on the electric toe-kick heater in the bathroom to take the chill out of the air, but then decided to fire up the Aqua-Hot instead to warm up the entire coach and preheat the main engine.  At a seminar in Gillette, Wyoming this past summer we learned that the Aqua-Hot needs to run with some regularity in order to run well, so this was an opportunity to do that and to check my work from yesterday for leaks.  The Aqua-Hot ran quite well, but as I feared there was a small leak at the gasket between the two halves of the check valve.  I will try one more time to get a couple of wrenches on this part and tighten it, but if that is not successful I will have to install the new check valve, which would take another entire day.  Ugh.  I like doing projects, but I don’t care so much for doing them more than once.

We had oatmeal for breakfast, which is always nice on a chilly morning and has a certain staying power for days when lunch is uncertain.  After breakfast we got our coach ready for travel while Butch and Fonda did the same with theirs’.  We departed Twelve Mile, Indiana a little before noon with Butch and Fonda in the lead and headed for Goshen, Indiana to attend the Great Lakes Area Motorcoach Association (GLAMA) 2013 area rally (GLAMARAMA13).

Our route was IN-16 (Co Rd 700 N) westbound to N Co Rd 600 E northbound to IN-25 northbound to US-31 northbound to US-6 eastbound to IN-15 where we stopped for a stretch break.  We moved into the lead and continued northbound on IN-15 to Goshen with Linda navigating based on directions provided by the rally organizers.  We had been advised by FMCA to follow the directions they provided in order to avoid a bridge that was out on the main road to the fairgrounds from the west.

We tend to travel on Intestate and US highways, but have also found State highways to generally be good for travel.  Even county roads are OK if we know in advance we will not encounter weight, height, or width restrictions.  This is where it is helpful to have local information from folks familiar with the roads.  It also helps that our Rand-McNally RVND7710 GPS is configured to know the parameters of our rig, so we are able to travel with some confidence that we will not encounter unexpected obstructions.  As an added feature it also provides real-time traffic information, especially near larger metropolitan areas.

The trip up IN-15 brought us quickly into the outskirts of Goshen with heavy, slow traffic.  This presented a challenge for us as the buses do not accelerate that quickly and the lights do not stay green for that long.  It was important that I not lose Butch at a light as Linda had the detailed directions for getting to the fairgrounds.  As we came to downtown Goshen there was construction with lanes closed and traffic rerouted through barrel lined jiggy-jogs.  We pressed ahead none-the-less as we needed to go east on IN-4, just three short blocks beyond the construction.  We made it through but it was the kind of situation that adds a bit of stress to the usual pleasure of driving the coach.

We continued east on IN-4 looking for Co Rd 29 southbound.  Along the way we spotted an official looking sign that said “RV Rally and Fairgrounds” with an arrow pointing down a nicely paved road to the south.  I slowed down and considered taking this road—even though the turn looked a bit tight—until I noticed the “NO TRUCKS” sign on the adjacent pole.  We are never sure whether or not we are a “truck” so we generally decide one way of the other depending on what is to our advantage.  In this case I took a “pass” and continued on down IN-4 to CR-29.  We headed south on CR-29 until it ended at CR-34 where we turned westbound back towards the fairgrounds.  Our directions said to enter at Gate 3, but as we approached the northeast corner of the fairgrounds an orange-vested parking crew member motioned us to turn in.  I hesitated again, but decided to follow his directions.  The parking procedures are usually well thought out and the crews usually know what they are doing.  The whole arrival/parking experience generally goes much more smoothly if you simply follow their directions.

(It is worth noting, however, that as with a boat or airplane the driver of an RV bears the ultimate responsibility for it’s operation and is the ultimate decision authority with respect to that operation.  If the driver is unclear or uncomfortable with what parking crew are asking them to do, the correct response is to STOP, ask for clarification, and not move until they are certain they understand where they supposed to go and are comfortable (willing and able) going there.  Arguing with parking crew, however, is counterproductive, and ignoring them and moving the RV is potentially dangerous.  Parking crew are there to move large numbers of RVs efficiently and safely to planned parking areas and drivers should always give them their full cooperation but never surrender their ultimate decision authority.)

We arrived at the rally venue a little before 2 PM.  The usual procedure is to unhook a towed vehicle and drive it, separate from the motorhome, to the site or a designated parking area.  And so it was today.  They had changed the entrance gate to channel us into an area where there was more room to unhook our towed vehicles.  With the cars unhooked, we proceeded to the holding area where we queued up and waited to be escorted to our site.  For this rally parking areas had been reserved for chapters so they could park together without having to arrive together (caravaan style).  We were part of the reservation for the Great Lakes Converted Coaches chapter (GLCC).  The parking crew was friendly and efficient and we “wheels down” (an aviation term) in our site by 2:30 PM with the coach set up and ready to use by 3:00 PM.

The reserved parking was an unusual feature of this rally, and an attempt by GLAMA to be as accommodating as possible in spite of the added complexity of this arrangement.  If you have not been to an RV rally, you won’t fully appreciate how nice it was to be able to park with “our group” without having to coordinate our arrival with everyone else.  Generally if RVs want to park together at a rally they have to arrive together in a caravaan.  The only aspect of their parking that is usually pre-arranged is the area of the facility they will be in based on the hookups (electricity, water, sewer, generator use) they have paid for as part of their pre-registration.  Even with a small number of RVs caravaning can be a challenge.  Wile some rallies provide an arrival area where RVers can meet up and form their caravan, many rallies do not have the space for this.  In that case, the RVers first have to find a place to rendezvous.  (Walmart is a popular choice, especially if folks are staying overnight there anyway.)  They then have to make their way to the rally site while trying to keep the group together at stop lights (which isn’t possible with more than two rigs).  GLAMA is to be applauded for trying this new approach.

Goshen is the county seat for Elkhart County, Indiana and the home of the Elkhart County 4-H Fairgrounds.  We had been to this facility once before for The Escapees RV Club Escapade in September 2010 and it is a nice facility for an RV rally.  Access to the fairgrounds is good, and the interior roads are more than adequate for large motorhomes (and converted buses).  The campgrounds can provide 30 Amp power and water for a large number of rigs (800+), and there are also some full hookup, 50 A sites.  There are many buildings and covered outdoor areas available for entertainment, vendors, seminars, and meetings.  And yet all of this is neatly contained in a surprisingly compact space that makes the venue very walkable while the paved roads make for good driving of toads and courtesy transportation golf carts.

This is the first Great Lakes Area Motorcoach Association (GLAMA) rally being organized by the officers and volunteers of GLAMA.  For many, many years the Great Lakes Area Spring Spree (GLASS) rally had served this purpose.  Held at the Berrien Springs, Michigan youth fairgrounds, GLASS was a nice rally at a nice venue held over Memorial Day weekend and consistently drew 800+ motorhomes until the last few years.  Unlike most FMCA area rallies, however, the GLASS rally was organized by the Michigan Knights of the Highway, the 4th FMCA chapter ever formed, and the oldest FMCA chapter still in existence.  MKH handled the registration process, and any financial benefit (or loss) went to them, not GLAMA.

GLAMA takes in Indiana, Michigan, Ohio, and Ontario Canada, so obviously it does not include all of the states that border on the Great Lakes.  Even so, it covers a large geographic area with lots of FMCA members.  GLAMARAMA 2014 is also slated for the Elkhart County 4-H Fairgrounds in Goshen, but the intent is to then rotate it to each state and Ontario for two years each.  That will entail more work for GLAMA organizers, but will open up the chance for more people to attend and build a stronger sense of ownership across the association.

Today was early entry day, so there were no official activities beyond arrival and registration/check-in.  Pat and Vicky Lintner were already parked at the GLCC area as Pat is the GLAMA VP for Indiana and part of the rally organizing committee responsible for all of the rally specific signage.  We pulled in next to Pat and Vicky, followed by Butch and Fonda.  Mike and Laurie Minnick pulled in shortly thereafter in their 1968 MCI MC-7 bus conversion.  Don and Sandy Moyer then arrived in their 1948 Spartan bus conversion.

[Note: The Spartan bus was built for three years, post World War II, in Sturgis, Michigan.  The owner/president of the company was the chief test pilot for the B-25 bomber.  All of the engineers and craftsmen came from the aircraft industry and the bus was designed/built much more like an airplane than a motor vehicle.  Only 57 Spartan buses were built and most of them ended up being used outside the U. S., including some used to make a 12 hour daily run from Damascus, Syria to Baghdad, Iraq and a 12 hour run back, making it the fastest bus line in the world at the time.  The Moyer’s bus was the last one built, a 28 foot model.  It was destined for a bus company in Wisconsin but they never took delivery.  It left the factory as a seated coach, was driven out of the factory, and the front tires came off the ground because it was too heavy in the rear end.  Within two years someone had purchased it, taken out the seats, and had it converted to a motorhome.  Many of the details suggest that it was “professionally” done, but the Moyer’s have not been able to track down who did the conversion.  It was eventually parked and left to rot for 35 years until Don and Sandy rescued it.  Based on their research there are no more than 12 of the original 57 buses still in existence and theirs’ is almost certainly the only motorhome.  Don worked 8 hours a day, 7 days a week, for 18 months to put it back in usable condition.  It is a truly unique RV.]

GLCC reserved space for eight motorhomes and the other three planned to arrive tomorrow. The chapter will have more members/rigs in attendance than that, but they will be parked elsewhere.  George and Sue Myers are parked within close sight of our group, but are located for their convenience in running the golf cart courtesy transportation service.  Don and Kathy Crawford from Ontario are in the VIP row as Don is a past president of GLAMA, which also entailed being the national vice-president representing the Great Lakes Area.  Ditto for Jon and Sondra Walker, who was the GLASS National Director until he moved on to become GLAMA President.  Jon was elected the FMCA Senior National Vice-President this past summer at the FMCA national convention in Gillette, Wyoming, so the number two national FMCA officer is a GLCC guy.  Ron and Meredith Walker, who just joined our chapter, are also here but are parked with the Frustrated Maestros.  Ron is a retired K-12 music teacher and is the conductor of the FMs.

Linda made something new for dinner: firm tofu slices pan fried with onions and Bar-B-Que sauce.  She served it on a sesame seed bun with a side of sweet corn on the cob and some Sam Adams Cherry Wheat beer to wash it down.  Sometimes simple is best.

 

2013_09_16 (Mon) Home Away From Home

Buses at Service Motors in Twelve Mile, Indiana.

Buses at Service Motors in Twelve Mile, Indiana.

Service Motors in Twelve Mile, Indiana has become something of a home away from home for our motorcoach, having spent quite a bit of time there since we bought it.  As I have mentioned previously, Butch is very handy and has lots of tools, including a machine shop where he can custom fabricate things if needed.  He has been very generous with his time, talent, and facilities, giving me a good place to work on our bus and helping me with it when I need it (which is most of the time).  We often stop there enroute to other places, especially rallies that Butch and Fonda are also attending.  Once again, we spent the day camped there.

Service Motors is Butch and Fonda Williams’ Crosley automobile parts business.  They are the only full-line parts supplier for these wonderful little cars, last made in the early 1950’s, and have an active customer base.  They rarely close their business, but decided they would for the week while we attended the FMCA GLAMARAMA13 rally in Goshen, Indiana.  (Butch and Fonda are basically the same ages as us and were married one day before we were.  They have run Service Motors for 20 years and would like to retire and move in to their 1989 MCI MC-9 NJT bus conversion, which they have done themselves from scratch.  The business and facility are for sale.)

Linda worked with Fonda on some accounting issues while Butch attended to various bus and business tasks.  I spent the day repairing a leaky fitting on the fuel return line from the Aqua-Hot to the fuel tank.  This fitting had been leaking since I installed it as part of the fuel polishing pump project.  It looked like a simple enough project, which meant it would take me most of the day; and so it did.

The fitting in question was on the lower end of a check valve (back flow preventer) at the back of a small compartment, which made access difficult.  (I mentioned this project in a blog post in early June 2013, and have an article about the Parker Fuel Polishing Module queued up to run in some future issue of Bus Conversions Magazine.)  The compartment was covered by a beauty panel with a door, so the actual access opening was even smaller.  “Luxury” motorcoaches often conceal functional systems behind “beauty” panels so that the bays look impressively sleek and shiny when the doors are opened.  What I see, however, is something that blocks my access to systems that I need to work on so I decided to remove the panel, permanently.  This is why simply projects take all day.

The panel was held in place by four “L” brackets concealed on the inside (of course).  I borrowed an angle drive from Butch which allowed me to remove the screws fairly easily.  However, when I installed the electrical feed and switch for the fuel polishing pump back in June, I drilled a hole through this panel, ran a wire through it to the pump, and mounted the switch on the outside of it.  I dismounted the switch and removed the ring terminal from one of the wires as it would not fit through the hole otherwise.  With the switch and wires out of the way I was able to remove the panel after cutting loose some old rubber caulk along the bottom edge.  This is why simple projects take all day.

The “compartment” in question is just the extra bay space at the business end of the Aqua-Hot.  In addition to the fuel polishing pump it houses the coolant expansion reservoir and fuel filter / water separator for the Aqua-Hot as well as the fresh water pump for the domestic water system.  Fortunately the cover on that end of the Aqua-Hot slides off easily after removing only three easily accessible screws (it happens occasionally).  This made access to the leaky fitting much better.

The fitting was NPT male on one end, for threading into the bottom of the check valve, and barbed on the other end for attaching the fuel return line from the Aqua-Hot.  Barbed fittings are designed for a one time, press on installation of a rubber line, i.e., once the line is pushed on it does not leak and it does not pull off.  To remove it I had to cut it just below the fitting.  I was then able to unscrew the fitting from the check valve.  I was fairly certain that this junction was the major source of the leak.  The threads still showed remnants of Teflon thread tape, but not much.

The other potential leakage point was the seal between the two halves of the check valve itself.  The check valve is a two-piece body with internal parts, and there is a gasket between the two pieces of the body.  I had inadvertently loosened this joint when installing the fuel polishing pump and had not been able to re-tighten it in place because of the limited access.  Although I had a spare check valve, I decided to try and tighten the one that was already installed as replacing it meant cutting additional tubing and un-threading/re-threading additional joints.

Butch’s brother John came over in the morning to help Butch (and me) with anything that needed to be done.  Butch had him change out the element on his main engine fuel filter / water separator while he worked on other bus and business issues.  Fonda split her time between business things and loading their stuff on their bus.  Even when they are closed, there is business to attend to.  By the time I finished my little project it was well into the afternoon.  Butch and Fonda worked a while longer and then we headed off to Rochester for dinner at Alejandra’s Mexican-American restaurant.  It was 9 PM by the time we got back to the coach and we headed off to bed.