Tag Archives: Gary Hatt (BCM)

2016/02/25-29 (R – M) Sand Castle Stallions Port

2016/02/25 (R) Siesta Key

We were up at 6:30 AM this morning and did not have coffee or breakfast.  We picked up Mara and Michael at 7 AM and headed west on FL-70 towards Bradenton.  Our destination was an endodontic office in Lakewood Ranch were Mara had an 8 AM appointment for a root canal procedure.  As we were coming into town Michael spotted a Dunkin Donuts.  Location duly noted.  I pulled up to the office building at 7:55 and we all went in.

The endodontist said the procedure would take about an hour.  Michael stayed to wait for Mara while Linda and I drove back to the DD for coffee and something to eat.  The DD was in a small shopping plaza next to a Shell station so I topped off the car’s fuel tank before we topped off ours’.  I bought regular gasoline (10% Ethanol) for $1.56 per gallon.  We were getting ready to leave DD when Mara texted Linda that she would be longer than originally thought.  The tooth needed a filling and the dental practice next door just had a cancellation and could take her right away.  That was fortunate for Mara as she and Michael are leaving on Saturday for a week long cruise.  She also wasn’t sure she could get in to see her dentist before July, which was much too long of a time to rely on the temporary filling the endodontist had put in place.

With Mara’s dental needs taken care of we headed west on FL-70 to I-75 south to Exit 207 and then west to US-41.  A short jog to the right (north) and back to the left and we were on Siesta Key Drive headed west to the island of Siesta Key.  We drove through the town, which was very quaint (upscale trendy, actually) and found a place to park with public access to the beach.  The Siesta Key beach is very fine white sands, reputed to be the finest and whitest of any beach in Florida.  We walked quite a ways south from our entry point past the main public entrance and numerous lifeguard stands, all of which were staffed.  The wind was strong and the waves were high and I took a few photos.

A group of Royal Terns face into the wind on Siesta Key Beach.  Siesta Key, FL.

A group of Royal Terns face into the wind on Siesta Key Beach. Siesta Key, FL.

When we got back to the car we exited the island via the southern bridge and drove down US-41 to Venice.  We found a parking spot, which is not easy in Venice, and walked around the historic downtown area, which is now a mix of quaint and upscale shopping and lots of places to eat.  It is a very attractive area but there were a lot of people there.

We were just window shopping when we walked past the TableTop store.  As the name suggests, they sell a wide variety of products used to set a dining table.  We looked around to see if they had plastic wine glasses but did not see any.  We were just about to leave when we spotted one.  It was smaller than we wanted so we asked if they had others.  They did, we just did not see them!  They were not plastic, however, but were made of polycarbonate.  That’s the same material used for contact lens blanks and motorcycle visors.  It felt heavy duty and had a slight bluish cast.  The sales associate assured us that they could be cleaned in a dishwasher and would not discolor, craze, or crack, and will not break even if dropped on concrete (although we do not intend to test that claim).  We bought four of them at $15 each.

Mara and Linda play in the fountain in Venice, FL.

Mara and Linda play in the fountain in Venice, FL.

When we had seen enough of Venice we returned to the car and drove a short distance to Cafe Evergreen in Nokomis for linner.  I had the veggie (vegan) burger and Linda had the vegan beet Rueben.  Mara had the stir-fry noodle dish, which both of us have had before, and Michael had the Chana Masala.  Our waiter, by his own admission, was having an off day but the food was good and we took our time enjoying it.

When we were done with our meal we were also done exploring for the day and I drove us back to Arcadia.  On the drive back we discussed plans for tomorrow, which included Solomon’s Castle in the late morning, Hermann’s Royal Lipizzaner Stallions in the mid-afternoon, some before and after errands, and a picnic lunch.  Back at the RV Resort we dropped Michael and Mara at her RV and then returned to ours.  We watched our Thursday night CBS TV programs and had some popcorn later in the evening.  We headed to bed at 11 PM, watched a few minutes of Charlie Rose, and then went to sleep.

2016/02/26 (F) Castle Stallions

Our two main attractions today were Solomon’s Castle, near Ono, Florida and Hermann’s Royal Lipizzaner Stallions near Myakka City, Florida.  Both locations were within 25 miles of Arcadia and each other, so we did not have to endure an excessive amount of car travel.

We picked up Mara and Michael at 10:15 AM, stopped at the local Wells Fargo bank branch, and then headed west out of town.  At the edge of town we headed north on FL-661 towards Ono.  We turned onto CR-665 and five miles later turned off onto Salomon Road to the parking lot of Solomon’s Castle.  We had the address in the GPS, but there were occasional old hand-painted signs confirming the route.  We arrived just before 11 AM, when the “castle” opens for tours, but the parking lot was already crowded.  We bought our tickets for the 11:30 tour and then strolled around the part of the grounds between the parking lot and the castle while we waited.  Horse Creek runs through the property, much of which was wet.

Michael and Mara by the horse statute near the entrance to Solomon’s Castle.  Ono, FL.

Michael and Mara by the horse statute near the entrance to Solomon’s Castle. Ono, FL.

Solomon’s Castle was built by, and is still the home of, Henry Solomon and his wife.  Henry, who is about to turn 81, is an artist who has been creating art objects for 76 years.  Much of the main floor of the castle is an art museum, although the walking tour includes the living room and kitchen.  Other living spaces are on the second floor and were not part of the tour.  There is also a guest bedroom available to rent for $125 per night but I do not recall if an overnight stay included breakfast.  There is, however, a scale “replica” of the Santa Maria that houses part of the onsite cafe and is run by Solomon’s daughter and her husband, who live in a separate house on the property.

Solomon’s Castle and his art are quirky.  Although we did not get to meet him, we came away with an image of his sense of humor, and caught a glimpse of him in his workshop while we were walking the grounds after the tour.  Solomon works in a variety of materials but mostly metal and wood, and mostly with discarded scrap materials including food cans, beer cans, and parts/pieces of automobiles.  I took quite a few photos while we were there.  I don’t know what our son’s professional opinion of Solomon’s corpus would be, but some of his pieces were interesting and we had to respect the sheer quantity of work he has produced.  He seemed to have a particular interest in Picasso, copying several of the master’s works in wood montage.

Mara, Michael, and Linda on the grounds of Solomon’s Castle.  Ono, FL.

Mara, Michael, and Linda on the grounds of Solomon’s Castle. Ono, FL.

From the castle we continued north on CR-665 up to FL-64, the Florida Cracker Trail, and then west about five miles to Wauchula Road where we headed south to Myakka City.  At FL-70 in Myakka City we headed east about 1/2 mile and pulled in to a local park on the north side of the road that affronted the west bank of the Myakka River.  The picnic tables were all bolted to the concrete slabs that served as the floors of the open-sided shelters so we ate our lunch in the shade.  The air temperature was in the mid-60’s, and there was a breeze, so we ate with our jackets on.

After lunch we headed west on FL-70 to the other side of Myakka City were we turned south on Singletary Road.  About seven miles down we found the entrance to the Hermann’s Royal Lipizzaner Stallions and Spanish American Riding School complex.  Hermann’s is the home of a group of Lipizzaner horses that tour North America.  The original horses were part of the 500 Austrian Royal Lipizzaner horses rescued by General George Patton at the end of World War II.  Gabby Hermann is the matriarch of the current operation and the original horses were brought to the USA by her father.  The Lipizzaner horse was first bred in Austria in 1565 from Arabian and Andalusian stock.  Six lines were produced and new Arabian and Andalusian stock have been included in the breeding since that time to avoid the negative effects of inbreeding.

Gabby Herman exercises one of the Royal Lipizzaner Stallions in training.  Myakka City, FL.

Gabby Herman exercises one of the Royal Lipizzaner Stallions in training. Myakka City, FL.

Hermann’s has open rehearsals (performances) every Thursday and Friday at 3 PM and Saturday at 10 AM when they are not touring, weather permitting.  These are not “dress rehearsals” as the houses and riders are not fully costumed the way they would be for a show while on tour.  They do, however, put the horses through all of their maneuvers.  The rehearsals take place in an open air arena connected to the nearby stables with a pair of gated fences.  There are bleachers on the two long sides of the arena and visitors also bring lawn chairs and set them up on three sides of the arena.  We arrived around 2:15 PM and there were already people there.  Admission was a $5 “donation” per person, but it was not optional.  It was well worth the price, however, and we made an extra contribution at the end of the show.

We secured good seats in the last row of the one of the bleachers at the top of the stairs with our backs to the sun.  That allowed us an unobstructed view for photography with light from a good direction.  It was a good thing we got there early.  Six fully-loaded tour buses showed up after we got there along with lots of passenger cars.  The bleachers were packed and the lawn chairs were at least two deep around the fence.  After the show we walked over to see the 17 day old colt and walk through the stables.  I took photos and also snapped a few shots of the tour buses after chatting with the driver of a 2016 Prevost H3-45 with a beautiful deep purple paint scheme.  I would sure like to have one of those to convert.

Five stallions work in formation at Hermann’s Royal Lipizzaner Stallions and Spanish American Riding School.  Myakka City, FL.

Five stallions work in formation at Hermann’s Royal Lipizzaner Stallions and Spanish American Riding School. Myakka City, FL.

When we were done at Hermann’s we drove back to Arcadia and stopped at Walgreens before returning to Big Tree Carefree RV Resort.  We spent a little time at Mara’s motorhome so she could walk Linda through the various cat and RV chores that needed to be taken care off during the next week.  With that done we stopped at the mail room.  We had a slip in our mail slot that there was a package for us in the office but it was after 5 PM and the office was closed.  We figured it was the shipment of Nutpods vegan coffee creamer but we would not be able to pick it up until Monday as we would not be around during office hours on Saturday and the office is closed on Sundays.

For dinner Linda made lentil potato burritos using various leftover ingredients that we wanted/needed to use up.  I opened the bottle of Barefoot Moscato wine, using the cork puller that Mara gave us the other night, and we had some for dessert.  We were both tired so we watched some TV, including the first of three episodes of a new Masterpiece Mystery series named Silk about barristers in England.  We did not watch the second episode as we had to be up early in the morning and it was going to end too late.

2016/02/27 (S) Port Miami

We were up at 6:30 AM and left at 7 AM for Dunkin Donuts where we got something to eat and a couple of large half-caffe coffees.  As planned, we were back at Mara’s motorhome at 7:30 AM.  By 7:45 we had Michael, Mara, and their luggage onboard and were on our way to the cruise ship terminals at the Port of Miami some three plus hours distant.

The GPS wanted us to go south on FL-31 but we had already decided we would take FL-70 east to US-27 and then take that south/southeast as far as I-75.  We stopped at a Marathon station in South Bay to use the restrooms and let Mara and Michael get some coffee.  We headed east on I-75 to its end point at MM 0 and then followed whatever roads the GPS told us to use to get to Port Miami.  When we were almost to the Port we deviated from the GPS and took the tunnel under the water to get to the cruise ship terminals rather than exit the highway and use the bridge.  There was some temporary confusion, and minor tension, surrounding this but soon enough we ended up at Terminal F where the MSC Divina was docked.

Traffic was heavy and chaotic, but we found a spot at the curb and got them unloaded.  A quick handshake and a hug and we were on our way.  I never cease to be appalled at the incredibly pour traffic engineering we encounter at major transportation terminals.  We did get a stunning view of the skyscrapers that dominate the downtown Miami skyline, but after a bit of driving around we managed to escape the island via the bridge and I was glad to be clear of the area.

Linda had researched vegan friendly eateries last night and selected one called The Kitchen.  It was near Miami International Airport, not too far from Port Miami, and basically in the direction we needed to travel to return to Arcadia.  She put the address in the GPS and we enjoyed a slow, late Saturday morning, drive through downtown Miami.  We arrived around 11:30 and there were only a couple of other diners there.  As is often the case, it was a slightly funky little place, but it had an entirely vegan menu with lots of interesting options.

The Kitchen is, in fact, the prep facility for a chain of local eateries, and plenty of other customers showed up while we were there.  We had the tacos, which included plantains, and the nachos.  The tacos were good, especially the plantains, but the nachos were outstanding.  Both were made with vegan chorizo sausage.  The nachos had a base of blue corn chips with beans, tomatoes, salsa, and cashew cream.  It was also a big serving.  For dessert we each had a coconut date ball and a gobi berry chocolate brownie.  Yum.  The Kitchen was a bit pricey but most of the ingredients were organic and the food was fresh and very tasty so we felt it was good value for the money.

We left at 12:30 PM and I turned the wrong way leaving the parking lot.  It turned out we were on US-27 headed north so we stayed with that choice.  The GPS wanted to put us on the Interstate/Tollroads but we knew that eventually it would put us back on US-27.  There was a lot of traffic and frequent traffic signals, but we eventually got clear of the developed urban area.  Not too far out we stopped at a roadside park with an airboat operation and switched drivers.  Linda told me later that I napped for about an hour but my experience of the situation was that I nodded off and woke up repeatedly because of neck discomfort.

We got back to our RV resort around 3:45 PM and stopped at the mail room on the way in where I retrieved a box of magazines from BCM.  The 3 PM Mardi Gras parade had just ended but some of the decorated golf carts and masked participants were still hanging around the activity building.  I made a mental note that the Mardi Gras dinner started at 7:30 PM and we returned to our rig.

We turned on our Verizon Mi-Fi and got our local network online.  I opened the box of magazines to see what was inside and e-mailed Gary to let him know what I received.  Linda needed to attend to Mara’s cats, Maui and Sabra, and we both had several updates pending on our iPads and smartphones.  We packed up the iPads and walked to the activity building where I set up our technology in the library while Linda went on to Mara’s Bounder to tend to her cats.

I got both iPads and both smartphones connected to the Internet via the resort Wi-Fi system, which can only be picked up at/near the activity building (which includes the office, lanai, library, dining room/kitchen, card room, and laundry room).  The best reception is outside in front of the building, as the antenna is on the peak of the roof ridge at the front gable, but the reception in the lanai and library is very usable.  There was one other person there using the Wi-Fi but she left shortly after I arrived.

The updates for our iPads took 500 MB and the smartphone updates took at least another 250 MB, so it was at least a 0.75 GB update session.  Our 12 GB monthly Verizon data plan works out to about 0.4 GB per day, on average, so we are trying to do our updates using the park Wi-Fi and save our data plan for web searches, document/photo uploads/downloads, and other work we want and/or need to do from our motorcoach.

While I was updating our devices Linda got a text message from Mara and I was able to watch the latest OK Go video and play a few games.  Kate sent me the link a week ago and I was waiting for a chance to use the resort Wi-Fi when there were few, if any, other users.  I also downloaded the latest issue of The Gypsy Journal digital edition.

When I was done I packed up and walked over to Mara’s rig.  Linda exchanged text messages with Mara.  She and Michael are on the Holistic Holiday at Sea cruise for the first time.  They had finished the opening session with Jessica Porter and Neal Barnhard, M.D. and enjoyed it very much.  They had just sat down to dinner and we’re excited about that too.  We enjoyed their enthusiasm and recalled what it was like for us the first time we went on this cruise.  Linda packed up a few things to bring back to our coach.  Mara made Broccoli salad last night and there was a lot left over that she wanted us to eat.

It cooled off quickly after the sun set and the overnight low was forecast to be 42 degrees F.  We closed up the coach and then had some of Mara’s broccoli salad along with vegan Italian “sausage” for dinner.  We finished the Barefoot Moscato wine, had a few grapes for dessert, and settled in to watch some TV programs on the local PBS channels before going to bed.  We had spent 7 hours driving/riding in the car today and we were tired.

2016/02/28 (N) Cat Care

It was cool in the coach this morning and I stayed in bed, under the covers, with the electric heating pad on, until after 7:30 AM.  The cats were persistent, however, and I finally got up and took care of their needs.  I turned on the Aqua-Hot diesel burner and the zone control thermostats for the bathroom and the kitchen/living area and the electric toe-kick heater for the front of the bus.  Linda got up at 8 AM as I was making coffee.

We had granola for breakfast, after which Linda packed up her laptop computer and gathered up papers related to work she needed to do.  She took the car and drove to Mara’s motorhome to tend to the cats and then work there.  She did not need to be online and figured the cats would appreciate the company, or at least get more accepting her presence and attention if she spent some quiet, extended time there.  I stayed at our rig to catch up on draft blog posts and attend to our cats.

Last week I downloaded the free version of an app called “OfficeSuite (Free) Mobile + PDF” and have been using it to write the drafts of my recent blog posts.  It works at least as well as the native iPad Notes app, better in my opinion (so far), and creates a native docx format Word document.  It also works with various cloud services.  Hypothetically that should save me the steps of e-mailing it to myself, selecting/copying the text from the e-mail, pasting it into a blank Word doc, and then cleaning up all of the junk caused by the Note app, which is considerable (numerous calendar hyperlinks).  I say hypothetically because I have not yet set up or tested the cloud sync feature.  That was on my “to do” list for today.

Around 11:30 AM it was getting warm in the coach under mostly sunny skies.  I opened windows and roof vents and then put out all of the awnings. I continued working on my blog posts from the last four days and was finally ready to upload one of them via a cloud service.  We have a Dropbox account but we also have OneDrive accounts as part of the Windows 10 OS on our notebook computers.  I don’t normally use OneDrive but I thought this would be a good opportunity to try it.

I set up the credentials to allow the app to connect to the OneDrive account attached to my OS login.  I then tried to move or copy the Word docx file for Wednesday’s blog post from “current files” to the OneDrive under Network locations but the OfficeSuites app would not give me the OneDrive account as an option.  I checked the Help screens for information to assist me but could not find anything pertaining to this specific problem.  The app has Pro and Premium upgrades available ($ and $$) but the feature chart indicated that interfacing to all five of the different cloud services was included in the Free version.  Rather than waste time on this I called David Aungier to let him know there was an updated version of his featured bus article in a folder in my Dropbox and then kept working on draft blog posts.

At 1 PM I was getting ready to walk over to Mara’s rig to get the shower supplies from Linda when she returned in the car.  We have been able to avoid removing the cats’ litter box from our shower by using the showers at the building by the swimming pool.  That also keeps the shower water out of our grey water tank, allowing us to go more days between dumps.  I got my towel and the soap from Linda and walked over to the shower house.

When I got back from my shower I trimmed my beard and shaved.  It had probably been at least a month since my last beard trim and I was starting to look a bit scruffy.  All cleaned up and feeling refreshed I dealt with a couple of e-mails and then returned to the issue of getting the OfficeSuites app to sync with one of my cloud services.  It appeared that Dropbox might be the best choice so I established the connection to that account.  Voilà!  I was finally able to copy a local Word file to the folder I had previously set up in my Dropbox for blog post documents.

I proceeded to finish each post in turn and copied it to the Dropbox folder which immediately uploaded it to the cloud server.  I checked my ASUS notebook computer to make sure the document had made it to the local hard drive.  It had, which meant I could move it to where I keep the draft posts and start editing it directly.  This was a big deal for me as I expect it to streamline the blogging process.

As I was working on all of this I realized that I had told Gary at BCM that I would review and comment on an article he had received from Lloyd DeGerald and would try to get it back to him by Sunday evening.  Lloyd is a highly experienced, factory-trained, Webasto / Aqua-Hot service and repair technician and has worked on our Aqua-Hot in the past.  His article was basically a terse service procedure consisting of a numbered list of steps.  There were some things that I was not clear about so I added comments and highlighted them in yellow.  I got the document e-mailed back to Gary, with answers to several questions he had asked, just as Linda was putting dinner on the table.

Dinner was an improvised dish of red beans and rice with onions, garlic, tomatoes, turmeric, and kale.  I added a little extra Tabasco hot sauce to mine and it was a very good dish.  After dinner Linda did the dishes and then we walked over to Mara’s motorhome, by way of the garbage trailer, to tend to the evening cat and rig chores.  Maui stayed out long enough to get up on the hassock and show some interest in me.  I let her smell my hand but when I tried to pet her head she swatted at me.  Too much, too soon.  She played with a cat toy that Linda shook around, ate her dinner, and disappeared into the bedroom.  Sabra stayed out the whole time we were there, ate her dinner, and chased feathers that Linda moved around.

We walked back to our rig before 8 PM and watched a special about the Manners of Downton Abby on PBS.  The overnight low was forecast at 54 degrees F so we closed the roof vents but did not close the coach windows all the way before turning in for the night.

2016/02/29 (M) Bonus Day

Last night was the Academy Awards but we did not watch the show.  We had not seen any of the films and were more interested in a pair of specials on the Manners of Downton Abby about the role of the show’s historical consultant whose job it has been to make sure all of the actors were as authentic as possible in their speech and mannerisms.

We got up this morning between 7:30 and 8 AM, which seems to have become our norm of late unless we have an outing planned that requires an early departure.  We had our usual coffee followed by granola with blueberries for breakfast.  We doodled on our iPads for a bit and I finished my blog post for yesterday and uploaded it to our Dropbox.  Linda noted that today was February 29th.  In a month that is usually two to three days shorter than all the others it was like having a bonus day.  I also enjoy the relative rarity of the event.

At 9:30 AM Linda packed up her computer and papers and walked over to Mara’s motorhome to tend to the cats.  She planned to stay and work a while and was expecting a call from Dave at the bakery around 10 AM.  I finished my coffee, got dressed, and settled in to work at my computer.

When Linda returned we walked to Walmart for a few grocery items before it got too warm outside.  When we got back and had the groceries put away, we reconfigured the back of the car.  After Mara’s arrival, but prior Michael’s arrival, we had reconfigured the back of the car.  We had removed one of the rear seats and put the other rear seat down so Mara could go places with us.  Most of the stuff went back in the car but in order to store the removed seat in the front bay of the bus and make room for some of the stuff from the car we had moved the air compressor and two of the four chassis stands to the passenger side engine bay.

Just prior to Michael’s arrival we reconfigured the back of the car again as we now needed four seats.  To keep our stuff out of sight and protect it from the weather we bought a small tent, set it up behind the bus, and put everything in it.

When Mara and Michael return from the Holistic Holiday at Sea Cruise on Saturday Michael is going to rent a car to and get them back to Arcadia from Miami.  He will be sticking around for another four weeks and they will need a car for most of that time as we are leaving Big Tree Carefree RV Resort a week from today.  So today we put both rear seats back up, emptied out the storage tent, reloaded the car, and repacked the front bay of the bus.

As long as we were working outside I stripped out the bad silicone caulk between the new passenger side lower windshield and the gasket.  I found a different product in one of our parts and supplies tubs and got it out.  I did not apply it, however, as I wanted to let the rubber gasket relax and hopefully reform to the glass.  In retrospect, it is painfully obvious that the Safelite installers did not know what they were doing.

It was a sunny day and by early afternoon the air temperature was 80 degrees F, so we put on our swimming suits and walked over to the pool.  We stopped at the office to retrieve our package of Nutpods non-dairy coffee creamer and put it in the mail room until later.  After a nice soak and vitamin D treatment we showered, changed into dry clothes, and walked back to the mail room to retrieve our Nutpods package and other mail.  Being the last day of the month our electric bill was there along with an invitation to the Michigan reunion lunch scheduled for July 14 in Concord, Michigan.  The Resort does have a strong sense of community, and people take that back to their home states/provinces when the leave.

I had a text message from Kerry Fear requesting payment for snowplowing services for February.  Linda wrote a check and got it ready to mail.

For dinner Linda made stuffed poblano peppers and pan-grilled them.  (We do not travel with an outdoor grill, either propane or charcoal.)  The stuffing was rice, black beans, tomatoes, scallions, vegan sour cream, cumin seeds, and Daiya vegan cheddar cheese.  So good.  We had some Barefoot Riesling wine after dinner and fresh mixed fruit salad (bananas, strawberries, and blueberries) for dessert.  I really like the way we eat.

After dinner we watched our usual PBS news programs followed by our usual CBS entertainment shows.  I stayed up to watch Charlie Rose’s interview with Tim Cook, CEO of Apple, Inc.  I was getting ready for bed and turned on the fresh water pump.  It normally runs briefly to build up pressure and then shuts off.  This time it just kept running.  That meant one of two things: either there was an opening in the system (faucet or leak), or the demand pressure sensor was not working.  I shut it off, put my sweats and Crocs back on, grabbed a flashlight, and went outside to investigate.

It was almost midnight but there was plenty of light from the resort street lamps.  I checked both sides of the utility bay and did not see any sign of a leak other than the small drip from the fill valve packing nut.  I turned on the shore water supply and opened the valves to allow it to flow through the softener to the coach.  Once the lines and softener were filled and pressurized I did not hear any further water flow, so I was somewhat confident that we did not have a leak in the system.  I left the outside water turned on so we could flush the toilet and run water to wash our hands.

Back inside I wrote a sticky note not to turn on the water pump and stuck it on the toilet seat.  Linda woke up right after I finally got to bed so I was able to tell her in person, but the note was still a good reminder.  I watched Tavis Smiley’s interview with Tom Waters of Pink Floyd and then went to sleep. February 2016 had been a very busy, but very satisfying month for us.

 

2016/02/05–09 (F–T) Super Windows Roadtrip

2016/02/05 (F) Windows 10 Upgrade

We had a long day yesterday and even though we were in bed before 11 PM we still slept in until 8 AM this morning.  I did not make coffee and we did not have breakfast as we were picking up Mara at 8:50.  We shut down our computers and iPads and packed them for travel.  We set the windows in the bus so the cats would be comfortable.  At 8:45 AM we loaded the car and drove over to get Mara.  We stopped at the Dunkin Donuts in Arcadia for coffee and bagels and then headed west on FL-70 for Ed and Betty Burns’ place in Bradenton.

Everglades National Park entrance sign on the road from Homestead and Florida City, FL.

Everglades National Park entrance sign on the road from Homestead and Florida City, FL.

The main purpose of our visit today was to upgrade Linda’s Samsung laptop computer and my ASUS notebook computer to Windows 10 using Ed and Betty’s unlimited broadband data.  A secondary objective was for Linda to purchase/download the latest version of Turbo Tax.  Our tertiary goal was to update iPad and smartphone apps.

We got to Ed and Betty’s a little after 10 AM, introduced them to Mara, and got busy setting up our computers.  We had a bit of a false start but finally had the Windows 10 installation process launched by 11 AM.  After quite a bit of conversation, Linda and Betty busied themselves making lunch and Mara settled in to go through her mail.  Once the files for Windows 10 appeared to be downloaded I initiated the update process for eight apps on my iPad2.  Betty washed off a bag of red grapes and set them out for all of us to enjoy.

At 12:30 PM we moved our technology to a coffee table in the living room to clear the dining room table for lunch.  Betty made a large pot of vegan chili mac and we had sliced avocado, tortillas, and potato chips to go with it, along with grapes and slices of Meyer lemons for our water.  Florida really is a good place to be if you want to “eat fresh.”

The ladies left around 1:45 PM to go for a walk while Ed and I stayed behind.  I connected my phone to their Wi-Fi and updated a dozen apps.  My computer was finally ready to configure Windows 10 at 2 PM and I went through the customized personalization rather than accepting the Express Setup defaults.  My iPad was up-to-date so I started working on this post while I waited for the Windows 10 process to finally finish.

It took until 2:30 PM for my computer to be fully booted up and usable.  About that same time Linda’s computer was finally ready to configure.  I wanted Linda here for the configuration choices so I waited for her return.  The ladies got back at 2:45 PM and Linda resumed configuring her machine.  We had originally planned to go see the 3 PM practice session of the Royal Lipizzan Stallions in Myakka City, but we would have had to leave at 2 PM to get there.  We will definitely go seem them, but for now this was, once again, deferred to a future day.

Linda purchased, downloaded, and installed the latest version of TurboTax and was done installing updates by 4:20 PM.  Her update process went smoothly, if slowly, and without any apparent hitches.  When the initial Windows 10 upgrade finished on my machine I did not have any of the quick start or system tray icons which concerned me greatly.  After rebooting my computer, more than once, the icons eventually returned.  I installed an undated driver for the NVIDIA GeForce graphics processing unit (GPU).  I also had a problem with the sound but was able to resolve it using the audio troubleshooter.

I rebooted my machine for what I hoped was the last time at 4:45 PM.  It took 15 minutes to fully boot up and I made one more check for updates.  It appeared that the operating system updates were all done but there were still updates to install for Adobe Photoshop and Lightroom, both of which are large and tend to take a long time to download.

By this point Betty had opened a couple of bottles of wine and convinced all of us that the collect best option for dinner was to order pizza and eat at their house.  Linda coordinated the pizzas and ordered them from Vertoris’ where we ate last night and which was only seven miles away.  While she and Ed were in transit to get the pizza and salad I updated Photoshop and Lightroom.  I started each program and Photoshop indicated that it had a problem with the video card driver and had disabled some of its enhancement features.  That was not an immediate problem as I do not presently make any use of Photoshop, but the incompatibility was distressing nonetheless.

I had done what I could in the way of updates for today so I shut down my computer and packed it away to clear the table for dinner.  Betty set the table and Linda and Ed returned a short time later with the food.  We sat down to a wonderful meal with friends that finally concluded around 7:30 PM.  It had been a wonderful day with friends and we had gotten a lot accomplished thanks to the use of their technology, but by 7:45 PM we were all tired and the three of us were on our way back to Arcadia.  We dropped Mara back at her motorhome at 8:45 PM and were back at our coach by 8:50 PM.  We watched the end of an episode of Endeavor and then watched another complete episode.  By then we were sleepy tired and went to bed.

2016/02/06 (S) Article Uploads

We slept in this morning until after 8 AM and so did the cats.  We lounged around in our sweats drinking coffee and eventually had granola for breakfast.  It was cloudy with rain coming and we considered spending the day in the bus in our sweats when we remembered that it was the first Saturday of the month.

The Everglades is vast and low, but is not a swamp.  Swamps involve stagnant water.  The Everglades is almost entirely shallow, but constantly flowing, water like a river.  Everglades NP, FL.

The Everglades is vast and low, but is not a swamp. Swamps involve stagnant water. The Everglades is almost entirely shallow, but constantly flowing, water like a river. Everglades NP, FL.

The Arcadia Farmers Market takes place on the first and third Saturday of each month so Linda texted Mara to see if she wanted to go.  She did, so we got dressed, picked her up in the car, and drove downtown.  To our disappointment there were only four vendors there and only two of them were selling food.  One was a local farm that had freshly picked Napa cabbage and locally produced honey.  Linda bought a head of the cabbage and Mara bought a cabbage and a jar of honey.  We took a short walk around downtown and then drove to Joshua Citrus Co.

At Joshua Citrus we bought a few Ruby Red grapefruit and a few Honeybelle tangelos.  Mara also bought a variety of citrus including Meyer lemons.  We stopped at Walmart on the way back to our RV resort for cat litter and a few sundry items while Mara picked up some groceries.  We dropped her at her motorhome and took a minute to meet another couple from Howell, Michigan who were just getting ready to pull out.  We then returned to our rig around 1 PM.

Linda made rollup sandwiches with soft tortillas, Napa cabbage, dark greens, and hummus.  At 1:30 PM she phoned Mara to see if she wanted to go for a walk and headed over to rendezvous with her.  I had a call earlier from Dave Aungier and called him back.  He had downloaded his BCM article from my Dropbox and reviewed it.  We went over a few minor changes, which I made to the Word doc, and discussed the process of submitting it to the magazine and working it through to publication.

Dave and I were done talking by 2 PM and it had started to rain lightly.  Linda had worn her raincoat but returned around 2:30.  By that time I had turned my attention to the three articles that Stacy had finished proofreading and returned to me.  I went through each one and accepted most of the changes.  I then went through each one and made sure I had all of the image files properly identified and organized.  I backed up all of the files, moved them to the READY folder, and then uploaded them to my Dropbox.  Once everything had transferred I e-mailed Gary (BCM publisher) and Jorge (layout) and let them know the files were there.  I had a few more e-mails back and forth with Gary and had to redo a panoramic photo that had discontinuities in it that I had not noticed.

Mara came to our rig to discuss some logistics related to the Holistic Holiday at Sea cruise that she and her friend, Michael, are going on at the end of the month.  As it turns out we will take them to Miami and pick them up when they return and take care of Mara’s two cats while they are away.  Mara waited for a lull in the rain and returned to her rig a little before 6 PM.  For dinner Linda prepared a salad with diced Napa cabbage and honey roasted peanuts and a homemade dressing made with rice wine vinegar, sesame and vegetable oils, Dijon mustard, fresh grated ginger, salt, and pepper.  It was very good.  She then reheated the leftover pizza from the last two nights.  The pizza was exceptional when it was fresh and, although it lost its crisp crust on reheating, it was still tasty as leftovers.

While Mara was visiting the leak around the bedroom ceiling vent/fan reappeared.  The lower outside corner of the lower passenger side windshield also leaked, but we expect that to happen every time until we do something to fix it.

After dinner we watched a couple episodes of Endeavor and then a couple of episodes of As Time Goes By.  After that we watched a PBS documentary on Jason Blair, the discredited New York Times reporter.  We caught a few minutes of news and weather and went to bed.

2016/02/07 (N) Super Sunday

Today was just one of those days.  It also happened to be Super Bowl Sunday, but that’s another story.  As we do most days we started our morning with coffee.”  As she often does on Sunday mornings, Linda made vegan pancakes for breakfast.  We split a ruby red grapefruit as well.

Though much of the Everglades is open, there are stands of trees throughout.  This one had a “face.”  Everglades NP, FL.

Though much of the Everglades is open, there are stands of trees throughout. This one had a “face.” Everglades NP, FL.

Linda walked to Winn-Dixie with Mara while I settled in to work at my computer.  My plan was to edit and upload blog posts but in the end I only got two more posts ready to go and did not get them uploaded.  Not that I was goofing off; I was busy all day but ended up taking care of other things.

For starters, I downloaded an updated version of the Logitech SetPoint software for my Logitech UltraThin Touch Mouse and then reconfigured the settings.  The mouse is capable of a variety of things with just subtle movements but seemed to be less stable than before the Windows 10 upgrade.  I was also having problems with my cursor jumping around while typing.  I initially noticed it while typing e-mails but noticed it later while working in Word.  Linda had the presence of mind to suggest that it might be the touchpad.  Sure enough, the touchpad was active.  That had not occurred to me because it wasn’t active under Windows 8.1.  Apparently the upgrade to Windows 10 activated it.  So much for maintaining my existing settings.

I had additional e-mails back and forth with Gary and Jorge at BCM, as result of which I updated the BCM page on our website.  I also e-mailed Brenda Phelan to check on the status of our tire covers.  When I finally got to work on blog posts I selected and processed several photos from our visit on Thursday to the Ringling Estate.  I then edited the two posts mentioned previously.

When Linda got back from Winn-Dixie she made rollup sandwiches for lunch with dark leafy greens and garlic hummus in soft tortillas.  We had red grapes to go with the sandwiches.  After lunch she walked up to the mail room.  I got a happy birthday card from our daughter and son-in-law, which was nice.  The eight pounds of coffee we ordered from Teeko’s back home had also arrived.  I checked the order to make sure it was correct.  It was, so I stored the box as we won’t need it for another couple of weeks.  I exchanged a couple of text messages with my daughter and decided it would be easier to just call her.  We had a nice chat.

Mara walked down to our coach mid-late afternoon and the three of us went for a vigorous walk through the entire RV resort.  We all returned to our bus and visited long enough for me to demonstrate the mapped location history feature in RVillage.  Mara headed back to her rig around 5:30 PM and Linda started fixing our dinner.  She made vegan Sloppy Joe’s with TVP and baked sweet potato fries.  Yum.

Eventually it was time for Super Bowl L (50).  I had intended to continue working at my computer all evening but my enthusiasm had waned and I found the game distracting.  We kept the volume down and played games until 9 PM and then switched the TV to PBS and watched Downton Abbey.  When it was over we switched back to the game.  It looked like the Denver Broncos were going to beat the Carolina Panthers so we watched a documentary on PBS/World about a family in Japan.  Linda went to bed when it was over but I switched to PBS/Create and watched a tribute concert to American film composer John Williams.  Jasper curled up with me for a while and then indicated it was time to go to bed.

2016/02/08 (M) Travel Prep

It got down to 40 degrees F outside last night and dropped into the upper 50’s in the coach.  Juniper stayed close to us for most of the night and snuggled up next to my head around 4:30 AM.  The cats must have eaten most of their food during the night as by 7 AM Juniper was most insistent that I get up.  I finally did at 7:15 AM, fed them, turned on the furnace, and made our morning coffee.  Linda was up by 7:30, plugged in the charging cable for our Verizon Mi-Fi, and was playing word games by the time the coffee was ready.  That girl really likes her word games

An Anhinga pruning its feathers.  Everglades NP, FL.

An Anhinga pruning its feathers. Everglades NP, FL.

Linda checked our Verizon account via her iPad and we had used 7.03 of our 10 GB of monthly data plus the 2 GB of extra allocation we got for downloading and installing the Verizon go90 app on our phones.  The data usage function on the Mi-Fi device (Novatel 5510L) showed 9.03 out of 12 GB as it combines all available data, so they were in agreement.  It’s a good thing we have the extra 2 GB each month for the next few billing cycles.  This current cycle (January 20 through February 19) has included iOS and app updates for both of our iPads, app updates for our Android phones, uploading of four BCM articles to our Dropbox (with lots of photos), numerous e-mails with large attachments, and upgrades from Windows 8.1 to Windows 10 on both of our computers.  Even though we made some use of the resort Wi-Fi while at the laundry room, and did the Windows OS and some iPad/smartphone upgrades at Ed and Betty Burns’ place using their unlimited broadband connection, it has been a heavy period of data usage for our Verizon account.  Twelve gigabytes is not enough data to get us through a typical month while we are away from home.

We had granola for breakfast with fresh fruit and juice and then settled in to finish our coffee and doodle on our iPads.  I e-mailed my blog posts for the last five days to myself and then download/installed the Gmail app on my iPad2.  We took showers, got dressed, straightened up the bathroom, and got on with our chores.  I turned on the electric block heater for the engine to warm it up for a maintenance start later today.

We are headed to Homestead and the Florida Keys tomorrow for four days so today was, in part, a travel preparation day.  Linda’s first task was a trip to the post office to mail the book she bought at The Ringling estate for Madeline’s Valentine’s Day present.

We are taking the car and leaving the cats behind in Mara’s care so Linda wanted to clean up the bus a bit.  We also both needed haircuts.  Linda made a 1 PM appointment at a place near the Winn-Dixie.  One of my tasks was doing laundry which I took care of at 11 AM.  Linda finally got hold of a real, live person at the Florida Toll Road Sunpass system but the account is in my name and they would not talk to her.  She found me in the laundry room and worked her way through the phone menu until she got back to an actual person and then put me on the phone.  The woman was very nice and very efficient and it only took about 10 minutes to get our account reconfigured so we could access it.  We logged in and confirmed that we still have a credit balance and updated our credit card information.

When I was done with the laundry I turned on the Aqua-Hot engine preheat loop.  When Linda got back from her appointment she cut my hair.  Another task was giving Mara a key to our coach and going over the care and feeding of our feline friends.  Linda took care of that.

A few days ago our Progressive Industries EMS threw another PE2 error code, which indicates an open ground.  The current error code is 0 (zero), indicating that everything is OK, so it is/was obviously a momentary problem.  Presumably the problem is in the resort wiring as that is what the PI EMS is designed to monitor and protect against.  I wanted to do done things with the bus chassis today so I took care of this at the same time.  Unlike last time, I shut off the circuit breaker at the power pole, unplugged the shorepower cable, cycled the breaker a couple of times to wipe the contacts, cleaned the contacts on the plug, inserted and removed it several times to clean the contacts in the outlet, plugged it back in, and turned the breaker back on.  All of that was designed to clean electrical contacts and remove a possible marginal connection.

Another thing I did today was start the bus engine, let it warm up, moved the bus aft and for slightly to make sure the brakes were not frozen, and re-leveled the coach before shutting the engine down.  I shut of the block heater and Aqua-Hot burner before starting the engine.  We are a little over half way through our stay here at Big Tree RV Resort and given the often humid, rainy conditions I wanted to make sure the brakes were not rusted closed.  I also wanted to check the fuel gauge as we have been running the Aqua-Hot diesel-fired hydronic heating system on cold mornings and it uses about 1/4 gallon of diesel fuel per hour when operating.  When I was done with this process I turned on the fuel polishing pump so it could run while we were away.

We still had enough gallons of fresh water on board that I decided not to dump and fill the tanks today.  With the engine/chassis stuff taken care of my main focus today, when not preparing for our trip, doing laundry, eating meals, going for walks, and dealing with e-mails, was working on my blog.  It may be the thing I want to do, but it is often not the thing I need to do, or in some cases, the thing I have to do.

I failed to record what we had for dinner but I’m sure it was tasty.  We watched TV for a while and then went to bed.

2016/02/09 (T) Road Trip

My night was interrupted around 1:30 AM by very strong wind gusts.  All of the awnings were out except the large patio awning and were perfectly capable of being damaged by the gusts.  I put on my sweats, slipped into my Crocs, and went outside to stow the awnings.  The two bedroom window awnings and the driver side living room awning are held open by straps with a loop on the end that slips over a hook mounted on the side of the coach.  The roller tubes are spring loaded and self-retract when the straps are released.  While retracting they have to be controlled, using a long metal rod with a right angle bend on one end and a semi-circle handle on the other, but are otherwise easy to deploy and stow.  Besides the possibility of the fabric tearing where it mounts to the body or the roller tube, we had the front end of the driver side front awning flipped up by a strong wind gust in Sheridan, Wyoming.  I would not have believed that was possible unless I had seen it happen, but we were not about to risk having it happen again.

An Egret stalks its prey.  Everglades NP, FL.

An Egret stalks its prey. Everglades NP, FL.

I spite of my sleep being interrupted I was up at 7 AM.  As we do every morning, we fed the cats, refreshed their water, and cleaned their litter tray.  We finished packing, adjusted the windows, loaded the car, pulled out as of our site a little before 8 AM, and stopped at the dumpster to drop off a bag of kitchen trash.  We drove to the local Shell station to fill the fuel tank and stopped next door at Dunkin Donuts for coffee and something to eat.  We then headed east on FL-70.

Our destination was Homestead, Florida and Everglades National Park.  Our route was FL-70 east to US-27 south to FL-821 south (which is part of the Florida Toll Road system) to its terminus at US-1 in Florida City just south of Homestead.  From there we headed west through Florida City and on to Everglades National Park.  This part of Florida is very flat but it was still an interesting drive.  It was cloudy and cool for the whole drive down.

We stopped at the Visitor Center to get a map and stamp our National Parks “Passport.”  We entered the park using Linda’s Senior Access Pass and a few miles in stopped at the Anhinga and Limbo Gumbo trails area.  We walked both trails, each about 1/2 mile in length, and I took quite a few photos.  By the time we got back to our car it was 1:30 PM.  We were hungry and wanted to get more information about boat tours so we drove the 34 miles to Flamingo.  We had lunch at the Buttonwood Cafe and went over to the Marina to check on buying fuel.  They wanted over $5 per gallon so I passed.

We also checked on the pontoon boat tours.  Two different tours were available, one into Florida Bay and the other into the Mangroves.  Both tours left on the hour starting at 9 AM with the last one departing at 4 PM.  The tours lasted just under two hours, and cost $35.  They did not take reservations and tickets could only be purchased the same day.  We decided to return to the park tomorrow and deferred any decision about the boats until then.

By this time, it was late enough in the day that we decided to start back towards the entrance 34 miles away.  We stopped at Pa-Hay-Okee and hiked the boardwalk before leaving the park for the day.  On the way back to our hotel we stopped at a Shell station in Florida City and filled the fuel tank for a more reasonable price per gallon.  We found the hotel, a Hampton Inn just off exit #2 of the Florida Toll Road between Florida City and Homestead, and checked in.  We had lunch rather later and were undecided about what to do for dinner, or when.  We drove across the street to the Publix supermarket, bought snacks for tomorrow, and bought red grapes, hummus, and sourdough pretzel nibblers to have for dinner in our room.

We had Direct TV in our room but eventually found PBS and CBS and watched our usual Tuesday night programs.  We also found The Weather Channel and Weather Nation and checked the current weather and forecast for the next few days with great interest.  Some of the coldest weather of the year was dropping down through the upper Midwest and Great Lakes, affecting the Northeast, mid-South, mid-Atlantic, and Deep South past our location and all the way to Key West. We had brought a variety of clothing, so we were prepared.

 

2016/01/16 (S) – 2016/01/20 (W) A Capitol Experience

2016/01/16 (S) Fort Myers Beach Marilyn

I got up at 8:15 AM, cleaned the cats’ food bowls, fed them, and then made coffee.  I replied to an e-mail from BCM publisher Gary Hatt regarding which article he planned to run in March and which one in April.  I then downloaded my photos from the last two days from my camera to my computer.  Linda slept in and did not get up until 9:10.  We both felt like we have had too much less-than-ideal food to eat the last few days and split a grapefruit for breakfast.

Our plans for the day revolved around meeting Linda’s sister, Sr. Marilyn, at noon at the Diamond Head Beach Resort and Spa in Fort Myers Beach where she is attending an educational conference and taking CPE courses to maintain her counseling license.  The conference was being put on by her religious community, the Sisters of St. Joseph of Corondelet.  Marilyn told us the resort parking was outside but the entrance had a relatively low bar over it so I took the ham radio antenna off of our car before we left at 10 AM for the drive to Fort Myers Beach.

Two hours should have been plenty of time to get there but we finally discovered the downstate traffic congestion that many fellow RV/snowbirds have mentioned to us.  The trip down FL-31 south was an easy, pleasant drive through citrus groves and ranches.  It ended at FL-80 where we headed west towards Ft. Myers.  We had the GPS set for “shortest route” so it took us through town instead of putting us on I-75 but it was an interesting route and we got to see different parts of the city including downtown and McGreger Avenue, which is lined with large Royal Palms.  It was also the location of the adjacent Henry Ford and Thomas Edison estates.  In spite of the traffic we will probably venture back there at some point to see the estates.

Apparently everyone was headed to Ft. Myers Beach today as the last few miles to get onto the island took one hour.  It was the worst traffic I seen in years.  There is only one bridge connecting the north end of the island to the mainland and there are two lanes of traffic that funnel down into one.  The lanes have a divider between them and are controlled by separate stop lights.  We had never seen anything like it before.  Linda texted Marilyn with a revised ETA.

Marilyn and Linda at the Diamond Head Beach Resort & Spa, Ft. Myers Beach, FL.

Marilyn and Linda at the Diamond Head Beach Resort & Spa, Ft. Myers Beach, FL.

When we finally pulled into the parking lot of the hotel at 12:30 PM Marilyn was waiting for us.  We paid for parking ($10), parked the car, and went directly to Cabana’s, the hotel’s beachfront bar/restaurant.  Linda had a margarita and I had a frozen strawberry daiquiri.  What can I say?  I like fruit drinks.

For lunch Linda and I both had veggie burgers and Marilyn had the Portobello mushroom burger.  The veggie burgers were mushy, as they often are, but the French fries were coated with something before being fried, probably flour, and were excellent.  After we were done eating Linda and Marilyn walked out onto the beach where Linda took her shoes off and walked in the ocean.  Our $10 parking fee got us a voucher for the same amount which we applied to the lunch bill.

We spent the next 90 minutes strolling a portion of Estero Boulevard, the main/only street that runs the length of the island.  I took a few photographs and we wandered into a few shops but did not buy anything.  We also walked out on the pier where we got a close up look at two Pelicans and a great view of the very crowded beach to the north and south.  This place definitely had that upscale but slightly funky, seaside resort, winter getaway vibe that is one of the reasons people flock to such places.

The Beach at Ft. Myers Beach, FL.

The Beach at Ft. Myers Beach, FL.

We were back at the hotel at 3:30 PM.  Marilyn had something to do at 4 PM so we took our leave and got back into the bumper-to-bumper traffic that was now moving slowly towards the bridge and off the island.  But at least it was moving, and once we cleared the bridge traffic moved along much better.  I changed the GPS to “fastest route” and it took us over different roads to I-75 and then north five miles to FL-80 where we retraced our earlier route (in reverse) to get back to Arcadia.  At the intersection of FL-80 and FL-31 we stopped at a Publix supermarket and bought a couple of bottled drinks.

It had been a long day and I did not feel like working at my computer.  We tuned in a program on PBS at 8 PM and doodled on our iPads.  Linda was checking the weather and the forecast for overnight was starting to look ominous.  When the program ended at 9:30 we went outside to retract our awnings and put our folding chairs and table away.  We stowed the big patio awning last and it started to rain lightly as we completed that task.  We left the TV on and watched the weather situation closely.  I finally went to bed at midnight knowing that we would not got a full, restful night’s sleep.

2016/01/17 (N) Bad Weather

The cold front that swept across the Florida peninsula overnight was draped off of an intense low pressure system that moved from Texas along the Gulf coast shore into the Florida panhandle and eventually along the Florida/Georgia border and off into the Atlantic.  The front, combined with a low level jetstream, raced across the area at 50 to 60 miles per hour triggering numerous thunderstorms and spawning a few tornados.

We had followed the development of the system closely before going to bed at midnight as both channel 11 and 20 had continuous storm team coverage.  At 4:30 AM we received severe weather alerts on our phones.  Linda’s phone has a loud klaxon warning sound associated with these alerts and we were instantly wide awake.  We put on our sweats, so that we would at least be dressed in case we had to leave the rig, and turned on the TV.

Arcadia, including our Big Tree Carefree RV Resort, was in the northeast corner of a tornado warning box.  It had started raining, off and on, well before midnight but as the storm front moved into our area thunderstorms came with it, one with Doppler radar indicated rotation.  There was lightning and thunder, of course, and the rain became steady and very heavy.  The wind really picked up but never became tornadic.  We stayed up until 5:30 AM by which time the main storm front had passed.  There were a few lingering cells behind it but the meteorologists gave the “all clear” for our area and we went back to bed.

The temperature was in the upper 60’s when we got up at 8:30 AM, rose slightly to about 70, and then dropped throughout the day as the front that triggered the storms raced off into the Atlantic opening the door for much colder air to flow in behind it, courtesy of the Polar Vortex that was plunging most of the Eastern U. S. and Canada into a deep freeze.

The rest of the day was uneventful with pleasant weather.  My focus was selecting and processing photos from the recent Arcadia Rally 2016 for the bonus content section of the digital edition of the March 2016 issue of Bus Conversion Magazine.  Linda worked on her counted cross-stitch project and went for several walks.  I joined her for brief strolls after lunch and dinner.  For dinner Linda made vegan chili from scratch.  It was very good.  We watched Downton Abbey on PBS after which Linda went to bed while I continued to work on photos.

2016/01/18 (M) The Capitol Steps

The air mass behind the cold front that swept out of the Gulf of Mexico, across Florida, and out into the Atlantic Ocean yesterday was noticeably colder and drier than normal for southwest Florida.  The temperature overnight dropped to 47 degrees, so we slept well and woke to clear skies and crisp air.

Our day revolved around the 3 PM performance at the Venice Theater of the political comedy musical group The Capitol Steps.  Venice is over an hour’s drive from Arcadia so we arranged with Steve and Karen Limkemann to make a day of it that would include lunch, photography at the Venice Rookery, the show, and dinner.

We skipped breakfast, showered, and dressed up enough to be presentable for the theater.  We gathered up several layers of outerwear and I put the 100-300 mm zoom lens on the Sony a99v.  We left at 10 AM and stopped at the Shell station in Arcadia to top up the fuel tank. Dunkin Donuts was right next door so we each got coffee and a blueberry bagel to split.  I got a frozen coffee drink made with almond milk and mocha.  I had never had one of these from DD and it was pretty good.

I had the GPS set for fastest route.  It took us out FL-72 towards Myakka State Park, which I expected, but then took us south on County Road 769.  Along the way we saw the usual assortment of citrus groves, ranches, and birds but also saw a Bald Eagle.  CR-769 turned southwest and eventually intersected I-75 where we headed “north.”  Although it was another 25 miles to the Nokomis exit, I-75 ran mostly east-west for this stretch so this route actually made a lot of sense.  It was only a couple of miles from the exit to Steve and Karen’s place and there was a Publix supermarket along the way, so we stopped and bought them a bag of M&M’s to replace ones we had eaten on our last visit and were going to eat on this one.  Not vegan, but a small indulgence.

We got to Steve and Karen’s place at Bay Lake Estates at 11:30 AM.  At 11:45 we walked to Cafe Evergreen about 1.5 miles away, an easy walk on a sidewalk without having to cross any major streets.  Cafe Evergreen is a small, all organic, restaurant with a good selection of vegetarian and vegan dishes.  We both had salads for lunch and they were very good.  Everything we have had to eat here has been excellent and the service has always been on a par with the quality of the food.

We walked back to Steve and Karen’s and visited until we left at 2:15 PM to drive to the Venice Theatre.  Parking can be a problem in downtown Venice but Steve found a parking space on a side street near the theatre.  We have enjoyed The Capitol Steps every time we have seen them and this show was as good as any.  Laughter really is the best medicine.

Herons and Egrets at the Venice Rookery, Venice, FL.

Herons and Egrets at the Venice Rookery, Venice, FL.

The show was done around 5 PM.  By the time we made our way to the restrooms and out of the theatre it was 5:15 PM.  Steve drove us to the Venice Rookery where we bundled up against the chilly air and Steve and I got out our cameras.  The sky was clear except for some thin clouds to the west and I took quite a few photos in the quickly changing light.  Sunset was just before 6 PM and we stayed until 6:30 to watch bats emerge from their purpose-built houses atop tall, slender poles.  We headed back to Cafe Evergreen where we had 7 PM dinner reservations.

Linda, Karen, and I drank lots of coffee, which was smooth and warm.  Linda and I had stir-fried kelp noodles with vegetables served over a bed of couscous with an Asian style sauce.  It was delicious and had a wonderful texture.  We each had a vegan indulgence for dessert; cranberry pecan for me and chocolate peanut butter for Linda.  It was a very satisfying meal.

We got back to Steve and Karen’s at 8:45 PM and decided to head for home.  We reversed our earlier route and were back at our coach before 10 PM.  We watched NCIS Los Angeles and went to bed, tired from a long, but very satisfying day.

2016/01/19 (T) VZW Data Usage

We left the windows open about inch yesterday, along with the kitchen ceiling vent (but no fan), so it would not get too warm inside from the sun while we were away.  It was cool inside when we got home at 10 PM and we closed up the coach in anticipation of the outside temperature overnight dropping into the low 40’s.  Last night was another cool one, literally.

Herons and Cranes at the Venice Rookery, Venice, FL.

Herons and Cranes at the Venice Rookery, Venice, FL.

There are only a few hot dishes that Linda makes for breakfast and most of them are a lot of work.  The one dish that is relatively easy is oatmeal, and it is a great choice for a cool/cold morning.  It stays warm long enough to eat it before it gets cold, is a hearty (and heart healthy) dish, and stays with you for quite a while.

Linda stopped at the resort office yesterday to see if they could cut the grass around our site while we were gone for the day.  The awnings were up and our chairs/table were still put away from the weekend storms, so the site was clear.  The office said they probably would not get to it on Monday as the ground and grass was too wet but when we finally left the coach today we saw that they had, in fact, mowed the area.

We have been on the go more than sitting still for the last week and needed some time at the coach to do things.  I needed to wrap up work on two articles for BCM and settled in today to do that.  Today (the 19th of the month) is also the end of our Verizon Wireless billing cycle.  We do not have park Wi-Fi at our site in Big Tree Carefree RV Resort and have been leaving our Verizon Mi-Fi on continuously.  We managed to use almost all of our 11 GB of data during the current billing cycle so I wanted to spend today working on photos for the articles and defer uploading them until tomorrow.

Before getting back into my BCM rally article I copied all of the photos that I took yesterday at the Venice Rookery from the camera to my computer.  Linda tries to create a new postcard for Madeline every Tuesday and wanted a picture from the Rookery.  My best photos were of individual birds or small groups but she wanted something that would give Madeline a better visual understanding of just what a rookery is.

 

I finally selected a photo with lots of different birds in lots of different positions, including some in flight.  Linda logged into the PhotoCardApp on her iPad and determined that the post cards the company creates and mails out are 8.25″ by 5.5″, which is a 3:2 aspect ratio.  That is also the native format of my Sony SLT-a99v.  Using Faststone Image Viewer (FIV) I was able to resize the image to the exact size of the postcard.  I then e-mailed it to Linda’s Gmail account which, in spite of our local area network in the bus, is the easy (only?) way to get it from my computer to her iPad.

While I was processing the image Linda looked up the term “rookery” and discovered that its meaning is more specific than we thought.  While it is, indeed, a place where birds roost and build nests (typically in trees) it is actually specific to rooks, which are a crow-like bird.  It has, however, become the generic term for a place where one or more species of bird roost, breed, nest, and raise their young.

Besides the main post card photo the PhotoCardApp allows you to create your own stamps.  Creating a stamp costs two credits but once it’s created you can use it over and over for just the cost of the postage.  (You get 30 credits for $25 and each card costs 2 credits to create, produce, and mail.)  We do not have a lot of photos of the two of us together as one of us (usually me) is typically behind the camera.  We have a nice head and shoulders photo that our son took that I use at the end of my BCM articles.  I e-mailed that to Linda and she used it to create a personalized stamp.  I found a second photo of us that someone took at the 2014 GLAMARAMA Rally so I processed it and e-mailed it to Linda to use for a second stamp if she wanted.  We are both wearing our bright yellow GLCC dress shirts, so it is very RV specific.

We tried Facetiming with Brendan, Shawna, and Madeline Sunday evening but the connection was too slow so we talked on the phone.  They were in Washington D. C. for a conference related to Shawna’s research and Madeline got to visit the Natural History Museum and see dinosaur skeletons.  The PhotoCardApp also has a large collection of “stickers” that can be added to a post card, so Linda added an electronic dinosaur “sticker” to the one she was working on.

A Great Blue Heron at the Venice Rookery, Venice, FL.

A Great Blue Heron at the Venice Rookery, Venice, FL.

The last couple of days there was some confusion between BCM owner/publisher Gary Hatt, the layout person (Jorge Escobar, in Columbia), and myself regarding which article they were running in the March 2016 issue.  Gary cleared that up in favor of my article on the Arcadia Rally 2016.  That, in turn, allowed me to move ahead with finishing that article today, which I finally did around dinner time.  My only breaks were to eat lunch and go for short walks.

Linda worked on her counted cross-stitch project but took time out to go on several longer walks, including one to the local Winn-Dixie supermarket.  She planned to make a bean soup for dinner and needed a few ingredients.  The soup was based on a package of mixed beans and lentils she bought at a health food store in Frankenmuth, Michigan back in October.  She added water, tomato sauce, garlic, onion, greens, chili powder, and turmeric.  By the time we sat down to dinner the sun had set and the temperature was dropping so the hot soup was not only delicious but really hit the spot.

We walked over to the mail room after dinner.  My new driver’s license had arrived.  The registrations and tabs for the bus and car arrived a few days ago so as of now we are not expecting any more mail.

Back at the coach I turned on the electric toe-kick heaters and plugged in the Broan portable cube heater rather than run the Aqua-Hot.  We put on our Tuesday evening TV programs but I was in a groove and turned my attention to selecting and processing photos to go with blog posts.  I got through my images for November and December and the first few days of January by 11 PM when the last show ended and Linda headed off to bed.

We still had 1.5 GB of data left in our current billing cycle, which ended at midnight, although I was not sure in what time zone.  I knew the data for my BCM Arcadia rally article was not more than 0.5 GB so I uploaded it before our data allocation reset.  It’s expensive to exceed our allocation but there is also a “cost” associated with not using what we have paid for.

I turned the thermostats on the toe-kick heaters back and turned off the Broan cube heater.  I turned on the electric heating pad on my side of the bed, set it to 4, and activated the pre-heat function.  I finally got to bed around 12:30 AM and snuggled in under the blankets.

2016/01/20 (W) Cellular Options

I don’t know if the outside temperature got into the upper 30’s last night but even with the coach closed up the temperature inside dropped to 59 degrees F.  Linda got up first this morning and turned up the thermostats on the electric toe-kick heaters.  I got up a few minutes later and turned on the Aqua-Hot diesel burner and the three thermostats that control the zone pumps and fans on the heat exchangers in the house portion of the bus.

We had slept in a bit and were sitting around in our sweats while the coach warmed up when we realized at 7:55 that the Wednesday coffee was starting in five minutes.  We did not feel like going over in our sweats or changing clothes so I made coffee in our coach like I do almost every morning.  The problems (for us) with the Wednesday morning coffee, based on having been one time, is that there is no opportunity to socialize and it takes too long.  It was well attended the one time we went so it apparently serves the needs of the resort management and most of the residents.

Linda used her iPad2 to check in on the world and I used mine to finish up my blog posts for the last few days.  We eventually had granola with blueberries and bananas for breakfast, which is always a treat.  Linda walked our kitchen trash over to the dumpster and then continued walking the park for her first walk of the day.

My original objective for today was to upload image and document files for my Arcadia Rally 2016 article to my BCM Dropbox folder, but I got that done before I went to bed last night.  Although I have a lot work to do on several websites, including ours, I wanted to put the finishing touches on my featured bus article about Ronnie and Diann Mewbourn’s 1969 Model 07 Eagle bus conversion and move two technical articles from “proofreading” to “ready” status.  Gary has not had Kathy proofread/edit any of them yet so that had to wait for another day.  I also wanted to continue selecting/processing photos for my January blog posts but got distracted with system updates for my ASUS laptop computer.

I ran the CCleaner program and then ran the Windows 8.1 disk check utility.  I ran it because MS Outlook keeps “encountering a problem and has to close” or stops responding.  The check disk utility did not find any errors so I downloaded a new version of Defraggler and started it.  I probably should have run it overnight as it ran all day and through the evening.  I think I could have worked while it was running but I have always preferred to let disk defragmenters run without anything else tasking the system.

With my computer tied up and my blog post drafts up-to-date I had a little time on my hands.  Linda is always up for another walk so we walked over to the CellularSales store, an Authorized Verizon Retailer located on an out lot of the Walmart shopping center.  The shopping center is on the other side of Highway 70 so we used the crosswalk at the traffic signal for the shopping center entrance.  This stoplight also serves the entrance to the 55+ community immediately to the east of our RV resort and is where we make our U-turn when headed east to head back west to the entrance to our resort.

The reason for our visit was that we became eligible for device upgrades back in April and wanted to check out what was available in smartphones and data plans.  We were also looking for a new Mi-Fi device that Chris and Cherie (Technomadia) reported on in their Mobile Internet Aficionados (MIA) site.  We usually work with Verizon corporate stores but there isn’t one in Arcadia.  The store was large, spacious, very nice, and not busy so Toby was able to spend some relaxed time answering our questions.

The Mi-Fi device we wanted to see was the new Netgear AC791L but CellularSales did not have one and Toby was not familiar with it.  They did not even have the Novatel 6620L and were still selling the Novatel 5510L which is what we have now and want to replace.  We got our 5510L in June 2013 from a Verizon retailer in Gillette, Wyoming and our friends at the RV Mobile Internet Resource Center (MIA) consider it obsolete and no longer even report on it.

We also looked at new phones and learned that the Samsung Note 4 and Note 5, along with the Galaxy VI smartphone, do not have removable batteries.  Toby viewed that as a negative and we agreed.  The Galaxy V smartphone, which does have a removable battery, would still be an upgrade over our Galaxy III phones.  It has a larger screen but not as large as the Note devices, which are almost too large to hold up to your ear.  Toby also showed us the new LG phone which was very nice but again did not have a removable battery.  It’s the newest competitor to the Samsung Galaxy S VI.  We will do more research before deciding what, if anything, to do.  The AC791L, in particular, appears to be available online without a contract and at a better price than in a retail outlet.

As long as we were on the other side of the highway we stopped at Walmart and bought a loaf of Italian bread to go with our soup for dinner.  When we got back to our coach the disk defragmenter on my computer was still only part way through the disk and indicating the time remaining as “> 1 day.”  The temperature outside was near perfect, not too warm or cool, so Linda got out one of our chairs and sat outside reading while I stayed inside and took a nap.

I got up a couple of hours later and wiled away what was left of the afternoon.  We have been keeping an eye on our male cat, Jasper, who has lost little patches of fur from several spots on his back, and finally decided that we should get him in to see a vet.  The closest one is on FL-31 less than a mile from our RV resort and is the one that folks in the resort recommended.  Linda was looking for reviews online but could not find the clinic so she drove over in the car to get the name and phone number.  It turned out that she had found the veterinarian’s name but he used to work out of his house at a different location.  We plan to drive out towards Lake Okeechobee tomorrow but will call the veterinary clinic first and make an appointment for Friday.

The Venice Rookery at sunset, Venice, FL.

The Venice Rookery at sunset, Venice, FL.

As the sun sank in the western sky the temperature cooled off quickly and we closed up the coach.  Linda heated the rest of the soup she made yesterday and we sat down at 7 PM to a simple but delicious dinner of soup and bread.  We turned on the TV after dinner, watched Jeopardy, and then switched to PBS to watch the Wednesday night nature/science programs.

The last 10 days have been very busy and somewhat intense for us.  We had been to the woodcarvers expo in Punta Gorda, visited with Steve and Karen, met Ron and Mary at Myakka State Park, visited with them again at our RV resort, attended the Tampa RV Supershow in conjunction with strong weather, visited Marilyn in Fort Myers Beach, dealt with severe weather again, followed by a long day of working on photos for my BCM rally article, had a long day visiting Steve and Karen in Nokomis again and seeing The Capitol Steps at the Venice Theatre, eating at Cafe Evergreen twice and then visiting the Venice Rookery to take photographs before returning home, had finally had another really long day yesterday selecting/processing photos and placing them in my BCM article.  Looking back at all of that we were probably due for an easy, low activity day, and one of the nice things about retirement is that we can usually have “do nothing” days whenever we want.

When I checked my computer it was still showing 17 hours to complete the defragmentation so I went to bed.

 

2016/01/06 (W) -10 (N) Websites, Woodwork, and Wildlife

2016/01/06 (W) Filtered Article 

The temperature dropped into the mid-50s last night and made for excellent sleeping conditions.  Never-the-less, Linda was up at 6:30 AM and read quietly until I got up at 8 AM.  I used the last of the current batch of coffee beans yesterday so I opened four fresh bags this morning, a half-pound each of Ethiopian Yirgacheffe (regular and decaffeinated), Seattle Blend (regular), and Sweet Dreams Blend (decaffeinated).  Teeko’s Coffee and Teas back home roasted and vacuum packed the beans for us in 1/2 pound amounts so they would stay fresh through the winter.  I made a full pot of the Ethiopian Yirgacheffe (half-caffe) and Linda prepared toast and grapefruit for breakfast.  One of the things we bought yesterday at Joshua Citrus was orange marmalade so Linda opened it and we had some on our toast.  It was not as bitter as most orange marmalades I have tried and I liked it.

Charlotte Harbor Event and Conference Center, Punta Gorda, FL.

Charlotte Harbor Event and Conference Center, Punta Gorda, FL.

Tonight was the weekly Powerball lottery drawing and the amount was approaching 400 million dollars so we agreed that we should buy a few tickets.  Since there was a possibility of rain this afternoon Linda wanted to get her walk in early so she walked to the Winn-Dixie supermarket in search of lottery tickets.  The Winn- Dixie is in a shopping plaza with other stores on the same (south) side of US-70 as the Carefree Big Tree RV Resort about 1/2 mile west towards downtown.  There is a very wide sidewalk along the south side of US-70 that is used by walkers, bicyclists, and folks in golf carts, from our resort and the much larger adult community just to our east, to get to the shopping area just west of us.  The Walmart is immediately across the street, with a stop light and crosswalk, but golf carts cannot go there as far as we know.

I’ve needed to change the water filter under the kitchen sink for a while so today I finally did.  I installed the GX1S01R GE Drinking Water Filter housing in fall 2014 to replace the Everpure unit that gave me no end of difficulty whenever I tried to change the filter cartridge.  It turned out that neither of our two filter wrenches fit the housing and I had to get my large slip pliers out to get it off.  The inside of the housing was dirty so I boiled some water in the microwave, added a small amount of dish soap, cleaned it thoroughly, and rinsed it out.

The GE drinking water filter element is a Class I media (0.5 – 1.0 micron) that reduces or removes more things than most filters, including:  MTBE, VOCs, Chlorine (taste and odor), Lead, Cysts, Mercury, Turbidity, and Asbestos.  The capacity of the element is listed as 500 gallons* (*depending on water conditions) and the useful life is listed as 6 months.  The filter feeds a special drinking water faucet in the kitchen sink that is only used for cleaning food and cooking so I doubt that we run anywhere near 500 gallons of water through it in 6 months, or even in a year.  Given how we use our motorcoach, and the cost of the filter elements, I will probably change the filter once a year.  To that end I wrote the date on a piece of Frog Tape and attached it to the housing.

I continued to focus on my article for BCM about Ronnie and Diann Mewbourns’ 1969 Model 07 Eagle bus conversion.  I thought I might get it done by lunch but I did not get back to work on it until after 11 AM.  I worked on it most of the rest of the day and into the evening and still did not get it finished.  By 9 PM I had the photos selected and processed but deferred integrating them into the article until tomorrow.  I will then upload it to our Dropbox and e-mail Diann that it is available for review.

Lunch was left over black-eyed peas, fresh fruit, and hummus with sourdough pretzels for dipping.  Dinner was salad and pan-seared tofu with caramelized onions in BBQ sauce with fresh strawberries for dessert.  We went for walks after both meals and Linda got in 10 miles today.

If we watch TV at all on Wednesday evening it is usually PBS and so it was tonight.  Nature was on cross-species animal bonding, Nova was on an archeological investigation of WWI trenches and tunnels, followed by a two hour program on the CERN LHC (Large Hadron Collider) and the search for the Higgs bozon particle and other, possibly more elementary ones.  It was after midnight by the time I got bed.

2016/01/07 (R) Jam Session

We were both awake around 7 AM.  Linda read for a while and got up around 7:45.  I drifted back to a light sleep and finally got up at 8:15.  By the time the coffee was ready to drink it was 8:45 AM.  Linda washed off some blueberries and poured our cups of Joe.

Linda bought 10 tickets yesterday for the Powerball lottery.  Our $20 investment returned $4.  The good news was that no one won and Saturday’s drawing will likely approach $700 million.  I know the odds of winning are astronomically small, but any non-zero chance to win even a piece of that pot seems worth another $20.  After all, you can’t win if you don’t play.

Linda by the signposts at the Charlotte Harbor Sheraton Four Points Hotel, Punta Gorda, FL.

Linda by the signposts at the Charlotte Harbor Sheraton Four Points Hotel, Punta Gorda, FL.

We had granola with fresh berries for breakfast.  I then e-mailed the Geeks on Tour to see if we could arrange a meetup.  That’s the name of Jim and Chris Guld’s business and they are currently just up the road at the Thousand Trails Preserve (RV park) in Zolfo Springs.  They are full-time RVers who do seminars and in-depth training classes on a wide range of technologies at RV rallies, parks, and other venues.  You can find them here:  http://www.geeksontour.com.  They also do a weekly podcast and have an extensive catalog of video tutorials.

I spent the morning and early afternoon finishing my BCM article on Ronnie and Diann Mewbourn’s 1969 Model 07 Eagle bus conversion.  I uploaded it to a folder in our Dropbox for them e-mailed them the link and some instructions.  I also sent the link to BCM publisher Gary Hatt.

We had hummus with sourdough pretzel nibblers and fresh fruit for lunch around 1 PM.  Our plan for the afternoon was to go watch a practice session of the Royal Lipizzan Stallions.  The U.S.-based stallions’ facility is just up the road in Myakka City and they have practice sessions open to the public at 3 PM on Thursdays and Fridays, and 10 AM on Saturdays.  They ask (charge) a $5 donation per person.  The facility has bleachers but you can bring your own chair.  We had planned to go today because the forecast for this afternoon was pleasant.

We want to order some fresh citrus fruit from Joshua Citrus here in Arcadia and have it shipped to our children in Michigan.  It will be much more economical for us to have it shipped to one place and Meghan agreed to receive it and distribute it.  We were going to stop there on our way to see the Lipizzaners but at 1:15 PM it was still overcast.  I wanted to take photographs so we decided not to go and will visit the facility another time.

With the change in our plans we took a long walk around the resort.  I then had to figure out something else to do.  I was tired and decided to take a nap.  The sofa was not available as Linda was working on her counted cross-stitch project so I curled up on the bed next to Jasper (the cat) and dozed for a couple of hours.

For dinner Linda fixed a side of mixed grains, steamed some broccoli, and sautéed a package of Gardein Orange “Chicken.”  The orange chicken is a soy-based dish and it is very tasty.

After dinner we turned on the TV and I worked on the bonus content photographs for my article on the recent Arcadia converted bus rally.  Perhaps because of the distraction from the boob tube, was trying to clean up a slightly complicated situation I had created for myself, was just not in the humor, or some combination of the three, I found the work a bit tedious.  I stuck with it long enough to get it better organized and then stopped at a somewhat logical point and watched TV.

2016/01/08 (F) Touring Geeks

There was rain in the forecast for overnight and I heard the first few drops before I went to bed just before midnight.  The rains came in earnest sometime between 4 and 5 AM and it rained hard around 7 AM.  I was awake at that point and decided to get up and check for leaks.  Fortunately there was no sign of the leaks we had during the last rain event.  I fed the cats, plugged in the charger for our Verizon Mi-Fi, and made the coffee.

Bruce by the signposts at the Charlotte Harbor Sheraton Four Points Hotel, Punta Gorda, FL.

Bruce by the signposts at the Charlotte Harbor Sheraton Four Points Hotel, Punta Gorda, FL.

After checking the user manual we determined that it is OK for the Mi-Fi to be plugged in and charging while it is turned on and operating.  The issue with the device is that it really wants to be unplugged from the charger once the battery is fully charged and can overheat if left connected.  Since we do not have a usable RV park Wi-Fi signal at our site it simplifies our online life if we can just leave the Mi-Fi on with the Wi-Fi Ranger connected to it.  The Mi-Fi battery is very slow to charge, especially when the device is turned on, but it eventually reaches full charge.  The battery will not even operate the device for 12 hours but it will operate long enough to get through the night.  What I am still trying to figure out is when to plug it in during the evening so that it is fully charged just before we go to bed.  That is a trial and process.  Once I have it figured out I need to make a habit of plugging it in when I get up in the morning and again at the right time during the evening.

After a little more discussion I e-mailed Jim Guld to confirm plans for a visit and dinner this afternoon.  We settled in with our coffee and iPads for a while and finally had breakfast at 9 AM.  Linda had two frozen toaster waffles she wanted to use up so we had those with peanut butter.  I also add a little apricot preserves on mine.  We split one of the Ruby Red grapefruits we bought at Joshua Citrus the other day.  Yum.

With company coming later today we took showers.   While Linda was getting her shower I copied recent photos from the Sony SLT- a99v to my ASUS laptop.  An updated version of the Play Memories Home software was available, so I downloaded and installed it.  After I showered, shaved, and got dressed Linda cut my hair.  We then cleaned the coach, putting away things that did not need to be out and sweeping/mopping the floor.

With the cleaning of ourselves and the coach completed, we went on an errand run.  After dropping off a small bag of trash our first stop was the Winn-Dixie supermarket.  We then drove to the Turner Agri-Civic Center to drop off recyclable plastic.  We swung by El Pirata Mexican restaurant to check out the menu and then drove to Joshua Citrus Company.  While I picked out some Sugarbelle oranges and Ruby Red grapefruit Linda ordered a three tray box of mixed citrus fruit that included Honeybelle tangelos, Meyer lemons, Navel oranges, and Ruby Red grapefruit.  The box will be shipped to our daughter and she will divide up the fruit with our son.  That arrangement allowed us to send more fruit at a lower cost than shipping to two addresses.  Our final stop was at Walmart for a few food items we did not find at Winn-Dixie.

Back at our coach I spent some time updating the Participants Database for our FMCA Freethinkers chapter (FTH) website.  I also spent some more time trying to recall just how I set up the WP-Members plugin for the SLAARC website so I can recreate it for the FTH website.  I was not able to do that in the time I had available and I think that might be due, in part, to changes that have been made in newer versions of the plugin.  I set up a WordPress User for Linda using the WP-Members registration form and it did not work the way I remembered it in the SLAARC website.  Apparently I am going to have study the user manual in detail.

Christine Guld called at 2:30 PM to let me know that she and Jim were on their way to our resort.  They arrived around 3 PM and we quickly settled into an easy conversation covering a wide range of topics.  Jim and Chris are the “Geeks on Tour” and do technology training (edutainment) at RV rallies and other venues.  They have seen and done a lot of things and are interesting, fun folks with whom to share time.

At 4:30 PM Jim drove us to dinner at Magnolia Seafood and Grill in downtown Arcadia.  The restaurant was almost empty when we arrived and we got a nice corner table by the front picture windows.  Today was Jim’s birthday and we enjoyed sharing it with him and Chris.  We lingered over dinner for almost two hours and by the time we left people were waiting in the lobby for a table.  I don’t like to wait for tables, but it’s usually a good sign when a restaurant is that popular.  Everyone said their meal was excellent.  Jim drove us back to our coach and dropped us off.  There was a music jam back at the Thousand Trails Peace River Preserve in Zolfo Springs starting at 7 PM. They wanted to cap off their evening there and we certainly understood.

We walked over to the resort office and picked up our mail.  My driver license renewal paperwork was there but nothing else.  Back at our coach we turned on the TV.  PBS/Create was airing the Las Vegas BeeGees concert from 20 years ago (again). With that as background we doodled on our iPads and eventually went to bed.

2016/01/09 (S) FTH Website Work

Our plan for today was once again to go watch the Royal Lipizzan Stallions practice session at their facility in Myakka City.  Fog moved in last night and was still thick by the time we finished breakfast at 9 AM.  That was when we needed to leave in order to get there and set up our chairs in time for the start of the session at 10 AM.  For the second time this week we decided to defer this event to a future date with better weather.

Black Crested Night Heron at the Peace River Wildlife Center, south of Punta Gorda, FL.

Black Crested Night Heron at the Peace River Wildlife Center, south of Punta Gorda, FL.

Linda resumed work on her counted cross-stitch project and I worked for a while on photos for the BCM article on the Arcadia Rally 2016.  No one won the Powerball lottery on Wednesday and by this morning the top prize had exceeded 800 million dollars, an all-time record for any lottery in the U. S.  Linda needed a few grocery items for our dinner and we wanted to buy a few more lottery tickets so we walked to the local Winn-Dixie supermarket to take care of those errands.  It was approximately a one mile round trip and on the walk back the cloud cover broke up into partly sunny skies.  Back at the coach we opened all three roof vents, turned on the exhaust fans, and opened the windows wider.

Linda settled back into her counted cross-stitch project and I turned my attention to our FMCA Freethinkers website.  I checked the SLAARC website (WordPress) to see how I set up the quick registration page through the WP-Members plug-in and then set up a similar (hidden) page for the FTH website.  I cleaned up a lot of other things on the website as well, including the member directory.  This work occupied the rest of the afternoon except for a lunch break and a brief walk.

Lunch was grilled “cheese” (non-dairy) and tomato sandwiches–very messy but very good–with grapes and orange slices.  The walk was brief because we stopped to visit with a couple from Ithaca, Michigan.  While we were chatting we watched low, thick white clouds moving towards us from the southwest against a dense, dark gray sky.  A couple of drops of rain was our early warning to return to the coach.

We got back before the rain started but once it did we closed the roof vents and reduced the window openings.  The forecast a few hours earlier had a chance of a thunderstorm at 9:15 PM but by 2 PM it was raining hard and an old leak around the bedroom exhaust vent/fan reappeared.  I also found a small leak at the lower outside corner of the new lower passenger side windshield.  We were both pretty discouraged at these continued leaks having hired people to fix them.  The heavy rain continued off and on for hours prompting Linda to track it in her iPad and eventually turn on the TV.  Lee County, which includes Fort Meyers about 45 miles due south of us, was under a tornado warning.  Arcadia is in Desoto County, which is the next one north, but the weather here was not severe, just wet.

While Linda was preparing dinner I e-mailed the members of our FMCA Freethinkers chapter to let them know that the public portions of the chapter website were now open for viewing and that I would be e-mailing each of them a unique username and password for the Members Only area in the near future.

For dinner Linda made a quinoa dish with julienned carrots, diced green onions, grated ginger, edamame, diced cucumber, and diced bell pepper.  She served it at room temperature and it was another fabulous dish.

After dinner Linda put on the Bengals-Steelers NFL playoff game while I started generating the usernames and passwords for the Freethinkers website.  I finished that work in about 90 minutes with the process of creating users automatically sending an e-mail to each member with their login information.  With that done I settled on the sofa with my iPad to finish up blog posts while we continued to track the weather.  The frontal system responsible for the wet/severe weather stretched from out in the Gulf of Mexico ENE across the Florida peninsula and was drifting to the east as storm cells raced along it.  Fort Meyers got 3″ of rain and sustained some wind damage from a rare January tornado.  The system was due to pass over Naples between 9 and 9:30 PM.  Our friends, Barb and Chuck, are there so hopefully they will just get rain like we did.

We did not have any more rain after dinner so we opened the roof vents and turned the exhaust fans on.  The forecast for Arcadia kept changing through the evening with the probability of rain around midnight bouncing up and down.  By the time we went to bed it looked like we might be done with precipitation for the night.

2016/01/10 (N) Wood Art

We made it through the night without any further rain or threatening storms and got up around 7:30 AM this morning.  We got dressed right away but I did not make coffee.  Our main objective for today was a visit to the Florida Winter National Wood Art Expo and Competition (FWNWAEC) in Punta Gorda.  We gathered up raincoats, camera gear, and a list of addresses for places we might visit, and headed out around 8:15 AM.  We stopped at the Dunkin’ Donuts in Arcadia for coffee and bagels and then continued west into downtown where we picked up US-17 and headed south to Punta Gorda.

The island at the Venice Rookery, Venice, FL.

The island at the Venice Rookery, Venice, FL.

We had a pleasant drive down and arrived at the Charlotte Harbor Event and Conference Center in Punta Gorda just after 9 AM.  The FWNWAEC opened at 9 AM so our timing was good.  The parking lot was mostly empty so I got a spot near the building and we finished our coffee before going inside.  Admission was $7 each and we got wristbands that allowed us to come and go all day if we wanted to.

We spent a couple of hours looking at all of the wood carvings on display and I photographed a few of them.  There were also lots of vendors selling tools, materials, supplies, and finished products.  At one of those tables we met John, who heads the woodcarving group at our RV resort, and learned that there will be woodcarving classes at the Turner Center February 8-11 and another exhibition there on February 20.  He invited us to stop by when the woodcarving group meets at the resort on Thursday mornings.

By 11 AM we had seen everything we wanted to see.  On our way out of the building the ladies at the entrance table were explaining to someone else some of the other things to do nearby and I heard mention of a Farmers Market.  I asked about its location and got directions.  Before leaving the event center area we walked the grounds around the Convention Center and Tiki Bar that is part of the Sheraton Four Points hotel next door.  We then headed south on Retta Esplanade through a nice area of wonderful homes on our left and waterfront parklands on our right.  There was a very large craft fair in progress but we passed it by in favor of finding the Farmers Market.

The market was inland a few blocks and was located in a smaller, but lovely, park where the vendor canopies were spread out along a winding pathway that led to a historic house which was open for visitors.  There was also a group of about eight musicians with guitars, fiddles, and such.  Linda bought a large Miatake mushroom after we sampled some and decided it was one of the best mushrooms we had ever tasted.  We found another vendor selling turmeric in root form.  She said it would keep for months so Linda bought a large piece.  At another vendor she bought sesame seeds and flax seeds, so the market turned out to be a good stop.

From the market we continued south in search of the Peace River Wildlife Center.  It was a small, private facility but had quite a collection of animals, mostly birds, that were being rehabilitated (if possible) for release back into the wild or living out their lives’ (if release was not possible).  A small donation was requested on entrance and willingly paid.  Most of the birds were in enclosures that made them difficult to photograph but the pelican area was open, and wild birds came and went, so I was able to get a few photos there.

From the Wildlife Center we drove back north into downtown Punta Gorda and the headed northwest on the Tamiami Trail across Charlotte Harbor towards Port Charlotte.  Our destination was the Earth Origins market in Port Charlotte which was, conveniently, located on the east side of the Tamiami Trail.  I say conveniently because the Trail was basically a 20 mile long strip mall.  It was six lanes divided plus left and right turn lanes, and choked with cars, so having the store on the side of the road we were already on was definitely convenient.

We were done with our shopping by 2:30 PM and realized that we were only 36 miles from Steve and Karen Limkemanns’ place in Nokomis (near Venice).  We called and got Karen on the phone.  Steve was out riding his bike but was due back soon.  They had no plans for the rest of the day so we headed their way.  We had been to their mobile home park (Bay Lake Estates) two years ago but had not been there since they bought their own place this past March.  It took about 45 minutes to get there, by which time Steve had returned from his bike ride.  We got a tour of their new place, which was one of the newer units in the complex and very nice.  We also walked up to see a unit that had caught fire and completely burned.  It was stunning to see how little of it was left.  The unit next door did not burn but the vinyl siding facing the fire melted and sagged.  Most RVs are built much the same way as mobile homes and park model trailers and they do not do well in fire situations.

Before going to dinner we decided to drive to the Venice Rookery.  We saw a sign for it driving up and wondered just what it was.  It turned out to be a large pond with an island that was a favorite resting and nesting area for egrets, herons, Anhingas, and other birds.  The island provide natural protection from land-based predators and locals told us that a large alligator protected them from any threat that might try to swim across.  I took what photos I could but had not planned on doing wildlife photography and did not have the correct lens(es) with me.

The temperature had been moderate during the day and our shorts had been appropriate clothing.  The best time to view the birds is apparently at sunset when large numbers of them return to the rookery.  As the sun sank towards the tree tops it got decidedly chilly and we finally had to call it a day.  We will be back on the 18th to see The Capitol Steps at the Venice Theater and made plans to return to the rookery with appropriate clothing and photo equipment.

From the Rookery we drove directly to Cafe Evergreen for dinner, an organic restaurant not far from Steve and Karen’s winter home.  The Café is not specifically vegan but always has some nice vegan selections.  Linda and I both had roasted beet Reuben sandwiches.  She had an edamame salad as a side and I had baked sweet potato “fries.”  We both had lots of decaffeinated coffee but no dessert as we were quite full by the time we finished our meals.

We went back to Steve and Karen’s place and visited a while longer before finally leaving a little before 8 PM.  Linda wanted to see Downton Abbey at 9 PM and we figured we had an hour drive to get back to our RV park in Arcadia.  The GPS wanted to take us south on I-75 but we went north 10 miles and took FL-70 due east through Myakka River State Park.  About half way to Arcadia we encountered an accident scene and had to wait for 15 minutes before we could continue our trip.  We got home a few minutes after 9 PM so we were still able to watch the show.  The Abominable Bride episode of Sherlock was rebroadcast following Downton Abbey so we watched it again.

The weather had cleared out behind the strong cold front that pushed through the area yesterday and temperatures overnight were forecast to drop into the upper 40’s.  We closed down all the windows before we went to bed.  I turned on the electric heater pad on my side of the bed before climbing in.  It had been a long day and neither of us felt like reading or writing so I turned off the lights and we went to sleep.

 

2015/12/28 (M) On to Arcadia

Even though we were pulling out this morning we did not set an alarm to get up at some particular time.  We were up by 7:30 AM anyway. I did not make coffee or have breakfast and started preparing for departure.  We packed up our computers and put them on the bed, put away remote controls, and turned off the laser printer and NAS.  While Linda cleared off counters and secured drawers I took care of some outside things.

I pulled the tow bar parts bags out, set them aside, got out the tow bar adapters for the car, and inserted them.  I folded up the two bag chairs and put them in the car and folded up the plastic table and stowed it in the front bay.  I checked the pressure in the two front/steer tires on the bus and they were fine so I did not have to get the air compressor and hose out.  I put up all of the awnings and opened the air valve for the engine accessories and toad braking system.

When everything else was ready Linda pulled the car out while I turned on the bus chassis batteries and started the bus engine.  I let the chassis air up, pulled up the tag axle, pulled out of our site, and then backed up until I was parallel with, and close to, the edge of the road on the passenger side and not blocking anyone’s driveway.  Linda pulled the car up behind the bus and we connected it for towing.  The breakaway cable finally broke so I got the spare cable out of the glove box but I could not get the key out of the disconnect.  Rather than risk breaking it and thereby disabling the car, we decided to travel without it.

We had a final, quick chat with our neighbor’s, Danny and Dorothy, and with Ken on the other side, and pulled away around 9:10 AM.  We were out of the resort and headed southeast on US-27 at 9:26.  At Ocala we headed south on I-75 as far as exit 301 (Cortez Blvd) at Brooksville, and headed east on FL-700 as far as US-98 and headed south.  Most of this segment was also co-terminus with US-35.  The drive was mostly rural and very pretty.  It was warm outside but patchy clouds kept the temperature inside the coach from getting too warm, at least for a while.  Eventually I turned on the OTR HVAC system and it worked well.

We passed through several smaller towns but eventually got to Lakeland which was much larger, with lots of stop lights and traffic, so it took longer to get through.  Still, it was an attractive community and something to see besides an Interstate highway.  The Detroit Tigers spring training camp is in Lakeland and we will likely drive up for some games while we are in this part of Florida.

US-17 joined up with US-98 as we were leaving Lakeland.  Somewhere south of Lakeland (Fort Meade?) US-98 turned east towards Sebring and we continued south on US-17 to Arcadia.  A few miles before reaching US-70 west of Arcadia we turned onto NE Turner Road which ran due south towards the Turner Agri-Civic Center and bypassed downtown Arcadia.  We pulled into the Civic Center, which was the rally venue, at 1:15 PM.

Linda checked in with rally organizers/hosts Bill and Brenda Phelan.  Linda stayed with the coach while Bill drove me over to check out sites.  I selected site #9 which would have us facing west with our passenger side facing north.  Although this orientation put the afternoon sun on our windshields, it also provided shade in conjunction with the patio awning.  Dan (?) led us over to the site and then left us to unhook the car and back the bus in.  We leveled the coach (we thought) and I shut it down and went through our arrival preparations.

The inside of the coach was cool from the OTR HVAC and I wanted to keep it that way, so we left the windows and roof vents closed and put the insulated foil panels in the three large skylights.  We also found the snap covers for the side windows next to the driver seat and installed those.  We were able to position the coach which generous space to our passenger side and far enough back that the 25 foot shorepower cord just reached the outlet box.  After plugging in we turned on all three of the residential air-conditioners.  We deployed all of the awnings, including the patio awning, to shade the windows and provide a shady place to sit outdoors.  We also have a fresh water and sewer connection but may not use them while we are here.  We are only here until Friday or Saturday and came in with a mostly full fresh water tank and mostly empty waste tanks.

Although it was very warm (86 degrees F) and humid the clouds had thickened and filled in during the second half of our drive and there was a good, steady breeze.  The bus ran well today including the OTR HVAC.  The low pressure light only came on briefly one time while I was idling at a stop light.  Apparently it works a lot better when it is relatively warm outside.

Once we were set up we had a light lunch of roasted red pepper hummus and sourdough pretzel nibblers with fresh apple slices and orange segments.  We then drove to Walmart to pick up some anti-itch cream and bought a few grocery items while we were there.  We checked out the filling station on the property and decided it was not a good choice for our bus.  We also found the entrance to Big Tree RV Resort which was, literally, across the street from the Walmart.  We drove back towards downtown and stopped at the Winn-Dixie to see if they had a better selection of boxed wines than the Walmart.  They did, and we bought a Franzia Crisp White.  We drove the rest of the way into downtown in search of a filling station with diesel fuel, and access for large vehicles, before returning to the rally site.

Linda wanted to go for a walk so we strolled past the buses and other RVs that were already here.  We ran into Scott Crosby working on Dan’s windshield.  We met Dan, Kathy, and their son James at the FMCA GLCC Surplus and Salvage Rally back in September.  Apparently the windshield on their GM PD4106 started coming out of its gasket along the top and caving into the cockpit on their trip to Arcadia.  Scott was up on a ladder getting the gasket reseated around the frame and glass.

We continued our walk and discovered that Paul and Claudine Elbisser, also from our FMCA GLCC chapter, were here.  We visited with them for quite a while before finishing our stroll around the rally and returning to our rig for dinner.  Linda microwaved a sweet potato and served the last of the Gardein stuffed mock turkey roll and broccoli that we had for dinner on Christmas day.

After dinner I tried tuning in OTA TV stations, orienting the antenna both WNW towards Tampa St. Petersburg, and due south towards Port Charlotte, Punta Gorda, and Ft. Meyers.  When I scanned for stations I found about 60 in each direction although many of them were the same stations.  So much for digital TV signals bring highly directional.  We watched reruns of our Monday evening TV shows on CBS.  We also turned on the Verizon Mi-Fi so we could get online long enough to check TV tower locations and network affiliations, check our e-mail, and change our location in RVillage.

I got an e-mail from Gary at BCM with the draft of the February 2016 issue and a request that I proofread Part 1 of my 2-part article on our Habitat For Humanity RV Care-A-Vanner build in July 2013.  I was a little tired from our day’s activities and was not in the humor to review articles, edit old blog posts, or write new ones so I just watched TV and fiddled with the thermostats and fan speeds on our air-conditioners.  I was puzzled by the fact that it felt humid in the rig in spite of the air-conditioners having been on all day.  The front and rear ones seem to be cooling better than the middle one, but the front one was the only one that we seaw water dripping from the drain line outside the bus.  I admit to having some level of concern about where the condensed water from the evaporators is going, assuming they are condensing any moisture.

The overnight low was forecast to be about 70 with morning fog, i.e., 100% relative humidity so in spite of the fan noise we left the bus closed up and the A-Cs running.  I adjusted the thermostats down to make sure the condensers would run, and lowered the fan speed in the bedroom to reduce the noise level.  I plugged the power in for the rear OTA TV antenna, but it was not functioning correctly and was clearly not going to fix itself.  It needs to be replaced but I am reluctant to buy another one of the same model as the failure rate so far has been 50%.  Linda read, and I played a few games, on our iPads and then went to sleep.

 

2015/12/14 (M) Christmas Stocking

I was up just before 7 AM to feed the cats, who were crying rather than using their usual technique of circling the mattress, and decided to just stay up.  I tried connecting my iPad to one of the nearby RV resort Wi-Fi access points but was still unable to connect to the Internet.  I tried to connect our WiFi Ranger to the access point but it was unable to acquire an IP address.  I turned on our Verizon Mi-Fi, connected the Wi-Fi Ranger to it, and started up my computer.  Linda was also up by this time and played a few word games on her iPad while I made coffee.

It was heavily overcast, but not foggy, and the sky glowed briefly with the rising sun before turning to a muted gray.  It was 71 degrees F outside, as dense cloud cover had prevented the temperature from dropping overnight, and 78 inside.  We left windows and the roof vents open last night with the bathroom exhaust fan on, so we had airflow but the humidity was higher than we like.  Still, we slept OK.

We had granola for breakfast.  After breakfast Linda drove to the Publix at the southwest corner of Gainesville to buy groceries.  I updated the other three WordPress websites that I manage and then got back to work on the HFH article for BCM which I did not finish yesterday.

I finished selecting and inserting photos for Part 2 of the article.  I then selected and organized the remaining photos for the digital edition Bonus Content sections for Part 1 and Part 2.  The penultimate step was to upload all of this to our Dropbox in a way that reflected the two-part organization of the article.  The final step was to e-mail Gary and let him know it was done.  Unfortunately this is at least the third time I have been “done” with this article so I won’t know if I am really, finally done until I see it in print.

We had a mock turkey sandwich for lunch and split an apple.  After lunch I sent e-mails to three friends who live south of our RV resort to try and arrange get-togethers before we leave at the end of the month.  I heard back from Bruce and Linda Whitney (really) right away.  They are members of our ham radio club back home and are in the process of relocating to their new home near Brooksville, Florida.  We agreed to get together this coming Sunday.  I eventually heard back from John and Marian Hogan and they were also interested in getting together.  By dinner time I had not heard back from Al Hesselbart, but I will.

Linda finished the needlepoint part of her project and walked to the sewing room by the office where she was able to use one of the sewing machines to attach the needlepoint matrix to a piece of white felt to make Madeline’s holiday stocking.  Our Verizon Mi-Fi had shut down when the battery drained so I plugged it in to recharge it.  I tried connecting our WiFi Ranger to the RV resort Wi-Fi and this time it worked.  There was obviously a problem with the system and it took until this afternoon for the office to get a technician out to fix it.

Gary Hatt at BCM had Kathy proofread the draft of my article on servicing the Webasto burner in our Aqua-Hot and sent it back to me.  I accepted all of her edits except one and then reformatted the article in two columns with the photos for the print edition inserted in-line.  I uploaded it to our Dropbox and e-mailed Gary.

We had both spent a long day mostly sitting so we went for a long stroll around the RV resort.  When we got back to the coach Linda started preparing dinner.  She added Halo orange slices to the salad, which included dried cranberries, walnuts, and sun-dried tomato dressing.  Yum.  The main course was couscous and black beans with corn, onion, and garlic.  Double yum.  We went for another walk after dinner.

When we got back we settled in to watch our usual Monday night TV programs and had a small glass of wine.

 

2015/12/11 (F) Naked Grape

We were both up at 7:45 AM but the cats were active long before that.  Besides their usual jumping on and off the bed they were unusually frisky and spent quite some time chasing each other back and forth the full length of the coach, often taking flying leaps onto the bed.  I fed them and Linda cleaned their litter tray after which I made coffee and she made oatmeal for our breakfast.  While we finished our coffee Linda played word games on her iPad and I put the finishing touches on yesterday’s post, e-mailed it to myself, and started working on today’s post.

My sister called at 9:30 AM and we talked for about 30 minutes.  When we were done I got dressed and gathered up the first load of laundry, drove it down to the laundry room, loaded the washing machine, and started it.  I then drove to the NAPA store to get the E-clips for the awning window lever pins.  This time they had them.  I ordered 12 but they came in bags of 20 and were cheaper per piece in that quantity.  There are 16 of these clips securing the lever arms for the eight awning style windows, so I bought the whole bag.  I also bought some J-B Weld that I plan to use to repair the broken weld on one of the passenger side living room window latches.

When I got back to the coach I gathered up the second load of laundry, which included the bed sheets and pillow cases, and drove it down to the laundry room.  The first load was done so I loaded it in the dryer and then put the second load in the washer.  I returned to the coach for 25 minutes and then went back to put the second load in the dryer.  It took several more trips to get all of the laundry in/out of washers and dryers, put in on hangers or fold it, and get it back to the coach.

For lunch we split a mock turkey sandwich with lots of greens, a tangerine, and a pear.  It was like a salad on a bun.  I had a text from my sister asking me to call a social worker at a different medical center and let her know that Patty would call her back later in the afternoon.  After lunch I called Amy and left a message.  Amy called me back and we chatted briefly.  Presumably she also talked to Patty later in the day.

Linda resumed work on her counted cross-stitch project and suggested that I select a bottle of wine for this evening and put it in the refrigerator.  None of the wines we had struck my fancy so I drove to the Grocery Depot and bought a 3L box of Naked Grape Moscato.  We received notifications from Amazon that two packages had been delivered so I stopped in the office on the way back and picked them up.  One was the two bath mats for the bathroom and the other one was our 8.5×14 brochure paper for our holiday letter. I put the box of wine in the fridge when I got back to the coach.

I finished the 2-column formatting of Part 1 of my 2-part BCM article titled What To Do With Your Bus:  Building with Habitat For Humanity and e-mailed it off to Gary, the publisher of Bus Conversion Magazine.  By the time I finished going through e-mails it was 3 PM and had gotten warm in the coach, even with the windows open and the roof vent fans running.  I laid down on the sofa and took a nap for a couple of hours.

When I finally got up from my nap the sun was low in the southwest sky and it had cooled off just a bit so we both sat outside with our iPads for a while.  It was a beautiful day today with clear skies and a warm sun and highs in the mid-70s.  Today is Friday, which means we gather at the fire circle at 7 PM for fellowship and music, so we had dinner at 6 PM, earlier than usual.  Linda made a nice green salad, as she does most evenings, with walnuts, raisins, and dried cranberries.  She reheated the leftover seitan stroganoff and heated some frozen broccoli.  She rarely uses frozen ingredients, but they are always handy to have around for a quicker, easier to prepare, meal.

Linda opened the box of Naked Grape Moscato wine and filled a small coffee thermos.  She put the thermos and our two plastic wine gasses in our wine tote and we walked down to the firepit.  We took the recyclables with us as the bins are just beyond the firepit.  When we got there at 6:40 PM John already had the fire going but no one else had arrived.  We like to get there early so we can sit near John and Ali.

As was the case two years ago I ended up tending the fire.  Not that I mind; I am actually pretty good at it, but the available firewood at the moment is not good.  It is very heavy for its size and I suspect it is not very dry.  I convinced John that we should leave the natural gas on under the logs.  Normally the gas is only used to start the fire but leaving it on, even on low flame, seemed to help reduce the amount of smoke.  I also used some of the scrap construction lumber which was very dry and burned hot and clean.

We stayed at the fire until 10 PM and enjoyed John’s guitar playing, singing along, and conversation.  Around 9:30 he got a call from a couple who had just arrived at the gate and he had to leave to escort them to their site.  They had been delayed by a traffic jam that resulted from an accident.  Every RVer who has been on the road for more than a few months has experienced this.  As was the case last weekend it was just the two of us with John and Ali at the end.  We would have stayed longer, as I had a small but nice fire burning, but John had to close up the resort buildings and check the gates and Ali was starting to get cold.  I turned off the gas, spread out the logs, and we headed home.

When we got back to our coach we turned on the TV and doodled on our iPads for a while before going to bed.  Linda inadvertently locked Juniper in the bathroom closet but after hearing an unusual thumping sound several times, and not seeing her anywhere, I investigated and found her.  She likes to climb in the closets and get behind things, and was actually reluctant to come out, but she finally did and ended up in bed with us and the other cat, as is the case almost every night.

 

2015/12/09 (W) Return to Satchel’s

I was up at 7 AM.  It was 66 in the coach; cool but tolerable.  I put on my sweats, fed the cats, and cleaned their litter tray, but did not turn on the heaters.  Linda was up by 7:15.  I made coffee and we delayed breakfast until later.  We are going to Satchel’s for dinner with John and Ali this evening so we decided to have brunch instead of breakfast and lunch.  Satchel’s has some of the best vegan pizza we have ever had, including a choice of vegan cheeses, so it will be a big meal for us.

Linda used her iPad to do some holiday shopping.  I checked my e-mail and was then going to play a few games on my iPad but the iOS 9.2 update was available so I started the installation process and set it aside.  Once the updated OS was installed I had five app updates available so I initiated those, one at a time, and started working on this post.  The updates downloaded fast enough to be reasonable.  Either the Resort has made significant improvements in the Wi-Fi and Internet connection bandwidths or very few people are using the system at the moment, or both.

I got the BCM boxes out from under the bed and integrated in the issues I received on Monday.  Everything was there so the three sets of issues are ready to give out as door prizes in at the Arcadia Rally 2016.  I worked on the photo tips article for BCM for a while and then decided to do some more work on the BCM page on our website.  I had a detailed e-mail from Gary at BCM with suggestions, and I find it easier to use that kind of information when it is printed out, but when I tried to print it my computer said the printer was offline.  The printer display said it was “Ready” so I had a problem to investigate and resolve.

This was the first time we tried to use the HP Color LaserJet 3600 printer since we put it on board the bus and it was the first time we had connected it via the Amped|Wireless SR20000G network extender / router.  I had expected it to plug-and-play as this trip was also the first time we have used the newer/larger NAS on the bus with this particular router and it worked without me having to do anything to configure it.

I downloaded an updated version of Advanced IP Scanner and ran it.  It could not find the printer and claimed that both of our computers and the NAS were “dead” connections, even though they were communicating with each other and the Internet.  All of the evidence suggested that the problem was somehow related to network addresses.  I went into the printer configuration menu via the front panel and changed two settings, turning on IP Release and IP Renew.  I turned the printer off and back on but that did not cause it to connect.

I went in and out of the control panel in my computer looking at the various screens related to devices and drivers, specifically printers.  I also went into the web interface for the SR20000G where some settings and context dependent help screens caught my attention.  In particular, the SR20000G appeared to be set up as a DHCP client rather than a server and the help screen suggested that it was getting IP addresses from the primary router, i.e., the one connecting our “home” network to the Internet.  In our motorcoach, that is our Wi-Fi Ranger, and the Wi-Fi Ranger operates on a different range of locally routed IP addresses (10.139.1.nnn) than most home networks (192.168.17.nnn).  I opened the Advanced IP Scanner again and figured out how to get it to scan the local address range served by the Wi-Fi Ranger and voilà, there was the printer, the NAS, our computers, and the SR2000G.

The final step was to revisit something that caught my eye earlier.  In the printer driver configuration there is a Port screen and the printer was configured with a Standard TCP/IP Port in the 192.168.1.nnn range.  I created one in the 10.139.17.nnn range to match the address that Advanced IP Scanner indicated had been assigned to the printer.  I tried printing a printer test page and voilà (again) I heard the familiar sound of the printer indexing a sheet of paper and shortly thereafter had the test page in my hands.  I went into my e-mail and printed the one from Gary.  This was not what I expected to be doing today but it was satisfying to get it resolved and not have it take any longer than I did to get it done.

One of our tasks for today was reinstalling the awning style window in the living room.  I happened to notice this morning that one of the lever pins on the other driver side window was coming out, indicating that the C-clip was missing.  Closer examination revealed that the lever pins on the four windows we had repaired in April 2014 were all reinstalled with pins put in backwards.

I took a break from my other work at 1 PM and drove to the local NAPA store to buy new C-clips.  The clerk at the store had a kit of clips and a paper template for matching style and sizes.  He said our existing clips are actually E-clips, not C-clips, and the size I needed was a 1007.  He did not have any in stock but ordered them from another store and said they would be in at 4 PM.  We would be on our way to dinner by then so I indicated I would pick them up in the morning.

Back at the motorcoach John stopped by to let us know that he and Ali were going to do some shopping before dinner and to figure out a time to meet us at the restaurant.  We agreed on 5 PM.  As long as he was here I gave him the bag of Fire Ant Killer I bought for him on Monday.

We decided that we would also do some shopping before dinner.  We left at 3:15 PM and headed up FL-121 towards Gainesville.  When we got to I-75 we headed north to the next exit at Archer Road (FL-24) and made our way slowly through the traffic, into the outdoor mega-mall, and to Walmart.  We needed a small hassock (that would double as a storage cube), a small table (that we could put between the two captains chairs), a non-slip shelf liner (to put under the printer), a seat cushion (for the card table chair at the desk), a small mat (to put on the floor outside the shower to catch cat litter), batteries (for our bathroom scale), and high quality 8.5×14 paper (to print our holiday letter).  We found all of those items except the last one, but did not buy the hassock as the store only had them in gray.  We then worked our way to the Office Max store at the center of the mall.  They only had one (open) ream of 8.5×14 paper and it was regular copy paper.  Useless for our needs.

We put the address of Satchel’s pizzeria/restaurant into the GPS and worked our way over to the east side of town through rush hour traffic.  We pulled into the restaurant parking lot at 4:41 PM just as John and Ali were stepping out of their Tahoe two spots down.  Satchel’s is a very popular place but at quarter to five it was mostly empty.  It was a lovely late afternoon but the sun was already setting and the air would being cooling off quickly so we asked for an inside booth, which also happen to have padded seats.

We started with a small salad that was still big enough to share with Ali and John.  They had pizza slices but we ordered a medium (13″) pizza with Daiya mozzarella cheese, onions, mushrooms, and sun-dried tomatoes.  Soooo good.  John and Ali split a bottle of Cabernet, Linda had water, and I had ginger ale.  Satchel’s makes their own soda pop and it is very tasty (but contains sugar).

By the time we left the restaurant at 6 PM it was full of people, inside and out, and the noise level had risen to where Linda and Ali were starting to have difficulty with conversation.  We settled our bill and went on our way.  John and Ali had more shopping to do but we headed straight for Williston.  As we were approaching the intersection at I-75 I noticed that I was getting low on fuel.  I probably could have made it to Williston, but why chance running out of gas.  There are five filling stations near this intersection but the Mobil station was the first one on the right so I pulled in.  A few minutes later we were on our way again and we arrived back at our motorcoach at 7 PM.

I put the cushion on the desk chair while Linda put the placemat in the bathroom.  We opened the folding table and adjusted the height so the cats’ scratching post just fit under it and put it in place between the two captains chairs.  Having a table in that spot has been the plan from the beginning of the remodeling.  Although the folding table is temporary, it immediately increased the functionality of the interior.  It also allowed us to better visualize how the living room will look/feel when we finally install the permanent table.

Linda spent much of the rest of the evening shopping for holiday gifts and domestic necessities on Amazon.  She got presents ordered for everyone except her sister, with all of them being drop shipped directly to the recipients.  She also ordered a 15″x15″ brown storage hassock and a pair of washable floor towels (for the bathroom).  We definitely get our money’s worth out of Amazon Prime.

 

2015/12/07 (M) Not on Vacation

I set my iPad alarm clock last night for 5:30 AM.  As soon as the alarm went off Jasper got up next to me on the outside edge of my side of the bed, snuggled in by chest, and wanted to be petted at great length.  I obliged him for as long as I could and was rewarded with his loud, resonant purring, which I could feel as much as hear.  I still managed to get out of bed by 5:45, feed the cats, get dressed, and be on my way by 6:08.

It’s only 75 miles from Williston to Suncoast Designers in Hudson, but the first few miles were a slow roll through the RV resort to the front gate followed by the short trip through downtown with a 35 MPH speed limit and several stop lights.  After a short distance on US-41 south I picked up FL-115 heading west.  A few miles past the airport it made a large sweeping turn to the south and continued on that heading for about 17 miles at 60 MPH until it joined up with to US-19.  I continued south on US-19 at 65 MPH for another 20 miles.  At that point it felt like I was making good time but I knew what was ahead as I had driven this route several times when we were here in 2014.

US-19 gets closer to the Gulf of Mexico the farther south you go, and with that closeness comes an increasing presence of people.  The first population center I came to was the charming little “Suncoast” town of Crystal River, followed by Ingless, Homosassa Springs, Weeki Wachi, and then finally Hudson.  These towns all have much lower speed limits and stop lights, and they get larger and closer together the farther south you go.  The side of the road changes from forest and farm to intermittent small businesses, then continuous shall businesses, and then suburban commerce that extends back from the main road until you reach Hudson which is a far northern suburb in the greater Tampa / St. Petersburg metropolitan area.  From Weeki Wachi on south US-19 is six lanes with a median, is lined with commercial properties, and has lots of traffic.

I arrived at Suncoast Designers a little before 8 AM so the trip took about an hour and 45 minutes.  I checked in at the office and they had someone meet me at the factory door to take the window and label it with my name.  We had this thermopane window repaired in April 2014 but the new seal did not hold.  Getting it repaired was one of our reasons for returning to Florida this winter.  Not the main reason, of course, but a factor in our decision.  I was back in my car and on the way home by 8:20 AM.  I will have to come back tomorrow to pick it up.

On the drive down I spotted a Dunkin Donuts about 10 miles north of Hudson on the west side of US-19 so I stopped there on the way back for a large coffee.  I had also seen quite a few filling stations between Crystal River and Hudson, many of them Shell stations, so I picked one that had easy access and regular gasoline (10% Ethanol) for $2.03 per gallon, cash or credit.

I remembered seeing an Office Max and pulled in when I spotted it.  By now it was well after 9 AM and businesses were open.  They had several different weights of expensive color laser photo paper but nothing like that in 8.5×14 (legal) size.  I did not need to have the paper today so I did not buy any.  I really do not want to redo our Holiday Letter for 8.5×11 paper so I will check online and see what I can get.  There was a Rural King at the same mall complex as the Office Max so I bought two bags of Spectracide Fire Ant Killer.  I also got a bag of free popcorn, which is available at all Rural King stores.  More places should do that, I think.

It was going on 11 AM by the time I got back to the coach.  Linda had been up since 7 AM and was ready to set her cross-stitch project aside and go for a walk.  I had been sitting for the better part of five hours so that sounded good to me.  We went for a vigorous stroll through the resort and arrived back at our coach ready for lunch.  Linda heated up a couple of vegan hot dogs and served them on the large whole wheat buns with mustard and relish.

After lunch I installed updates on the FMCA Freethinkers chapter website, the FMCA GLCC chapter website, and our personal website.  I then took snapshots in Adobe Reader CC of the covers of the BCM issues for July through December 2015, post-processed the covers, and uploaded them to the BCM page on our website along with brief descriptions of my articles that appeared in each issue.  I finished inserting photos into the OASIS Combi article I’ve been working on for BCM and will upload it to our Dropbox and e-mail Butch this evening.

It was a gorgeous day so we sat outside for a while and I worked on this post.  That is one of the things I really like about my iPad.  An earlier e-mail from Gary indicated that my package was out for delivery today.  I was about to get in my car and drive to the office when Joe and Teresa from Brighton, Michigan stopped in their golf cart to chat.  When they went on their way I dropped off the recyclables on my way to the office, picked up the box of magazines (which was heavy), and returned to the coach.

I worked some more on this post on my iPad but by 5:30 PM I had been up for 12 hours on too little sleep so I took a nap until 6:15 PM when Linda woke me up to have dinner.  For dinner Linda made a green salad with fresh blueberries and strawberries and made black bean smothered sweet potatoes.  Besides the black beans, the topping had tomatoes, scallions, cumin, and coriander and was finished off with a dollop of vegan sour cream.  Yum, yum, yum.

We watched the PBS NewsHour, another thing we typically never do, but then we do a lot of things differently when we are away from home.  We then watched our usual Monday night TV programs on CBS.  Even when we are away some things don’t change.  We are not “on vacation” after all.  We don’t go on vacation to get bus windows repaired.  In fact, we no longer go on vacation, we simply blend new experiences into our everyday lives.  Such is the nature of retirement as extended-time RVers in a converted bus.

 

2015/12/05 (S) Saturday Night Fire Circle

I was awake at 6:30 AM and finally got up at 7:15.  I fed the cats and cleaned their litter tray, both of which are chores but I don’t mind doing them.  I sat on the sofa with the heater pad on my lower right back and finished yesterday’s blog post draft.  Linda got up at 8 AM having been awake since I got up.  At 8:20 I was going to make coffee but Juniper climbed in my lap so Linda took care of that chore, which is certainly one of our more pleasurable.

Linda worked on her counted cross-stitch project and I worked on our Holiday Letter all morning.  I had a finished draft by lunch time and Linda read through it.  I have it set up for 8.5×14 inch legal size paper, but printing it that way will depend on whether we can get high quality glossy color laser paper in that size.

Linda reheated the last of the red beans and rice for lunch after which I washed some grapes.  After lunch Linda continued to work on her project and I turned my attention to another article for Bus Conversion Magazine.

I had some correspondence with the publisher, Gary, yesterday regarding my article on servicing the Webasto burner bearings and decided to finish my article on Butch Williams’ installation of an International Thermal Research OASIS Combi in their MCI MC-9 NJT bus conversion.  The work was done in October and November 2014 and the article was basically written in January 2015 but I had not selected or processed any of the photos.

I read through the article, highlighted several places with missing information, and rewrote some things.  I then selected 36 photos and started processing them.  The processing involved various adjustments such as alignment, lighting, and color followed by resizing and sharpening in two different sizes.  The larger size is typically 1900 x 1272 pixels as that will fill the screen of a 17 inch monitor and I don’t feel a larger size is needed or supported by the level of detail in the images.  The smaller size is typically 300×200 pixels.  I embed the smaller images at the end of the Word document with the image number and a caption.  I used to embed them into the article but the editor and layout person need the ability to fit them into the layout and I ultimately developed enough confidence in them to do that.  This is always subject to change, however, as is everything connected with this magazine.

We had dinner at 5 PM, earlier than usual.  Linda made a nice green salad, sautéed and lightly glazed some baby carrots, and heated some Amy’s vegan macaroni and cheese.  The reason for the early dinner was the holiday parade down Main Street in Williston at 6 PM.  We left at 5:30 and walked to the corner of NE 5th Street and Main Street.  NE 5th Street is the street that leads back to the front entrance of the resort and is towards the end of the parade route, which comes down Main Street from west to east.  There were already people there, all from the RV Resort as near as we could tell, but we were early enough to get seats on the low brick wall that borders the parking lot for the funeral home.

Main Street is also US-27 but the police closed it down at 5:45 PM.  The parade started at the west end of Main Street by the high school so the lead police motorcycles did not reach us until 6:20 and the front of the main parade did not get to us until 6:30.  There were cars with beauty queens, simple floats with seasonal themes, Girl Scout and Boy Scout troops, politicians, fire trucks, horses, and an elephant with Santa Claus riding on top.  It was a classic small town holiday parade.  It was all over by 7 PM and we walked briskly back to the firepit.

The firepit at WCRVR is about eight feet in diameter, surrounded by a concrete floor ring about six feet wide and covered by an inverted conical roof about 24 feet wide at the lower eaves.  A massive 8 foot diameter inverted conical hood is suspended over the firepit and the 12″ diameter flue pipe runs out the center top of the roof.  The outside perimeter of the floor has large wooden rocking chairs (think Cracker Barrel restaurant), a bench, and a few other chairs and there is a little bit of lighting up in the ceiling.  It’s a wonderful place to sit and enjoy the fire, visit, and listen to people play their guitars and sing.  The flue does not draft correctly so it tends to be smokey, but that is the only downside.  If not for that it would be perfect.

John was there with a couple of other people and had a nice fire going.  Even though it was in the mid-to-upper 60s there was a strong north breeze and the fire felt good.  Lots of other people eventually showed up and filled almost all of the seats so John got his guitar and started playing and singing.  Linda walked back to our rig to fetch our plastic wine glasses and opened a bottle of Egri Merlot.  It’s a good life.

I got a call from my sister and stepped away from the firepit.  She called to let me know that our dad was back in the hospital.  When I returned to the fire circle John was busy playing and singing and some folks had left so I tended the fire.  By 9 PM everyone had left except for John, Ali, and us.  I continued to tend the fire while the four of us talked.  Just before 10 PM I spread out the last embers of the fire and we all returned to our rigs for the night except John, who does the closing rounds on weekends.

Back at our motorcoach Linda put on the Michigan State vs Iowa Big 10 Championship football game.  Though not particularly interested in football I was too tired to work so after sending an e-mail to our son I laid down on the sofa; the first time I have done that since we built it into the coach.  By the time the game was over it was 11:45 PM.  We watched a few minutes of Cook’s Country on Create and went to bed.  I turned the TV on in the bedroom then turned it off.  I turned down the brightness of my iPad display and with only the dim light of the ceiling vista, and whatever light could get in around the window shades, worked on my blog post until 1 AM.

 

2015/12/02 (W) Settling In

I was up at 7 AM, fed the cats, and settled in on the sofa with the heater pad on my lower right back to work on my iPad.  I finished my blog post for yesterday and e-mailed the last three days to myself.  I updated seven apps and then checked out the latest issue of the SKP Photographers BoF newsletter.  Linda finally got up at 9:15 AM.  I made a pot of coffee and we had toast for breakfast.

My first priority after breakfast was responding to a half-dozen e-mails from Gary at BCM, one of which required me to proofread an article he had written about a recent rally.  Next I selected four photos I took with our new Sony a99v DSLT camera and uploaded them to a Dropbox folder for Lou to see.  Somewhere in there I got a call from Joe (our mobile mechanic) about Globus cork flooring products.  As long as he was on the line I asked his opinion about the chassis battery / Vanner equalizer issue.  He reminded me, as he often does, that I already knew how to check if the Vanners were working.  When we concluded the call I went outside and did the checks.

With the Vanners connected to the batteries and working correctly the voltage at the “12V” terminal should be exactly 1/2 the voltage at the “24V” terminal.  Equivalently, the voltage from +24 to +12 should be the same as the voltage from +12 to Ground.  I unplugged the two maintenance chargers to let the surface charge bleed off and used the time to trace the wiring behind the two battery disconnect switches.  As I somewhat expected the two Vanner equalizers, which are wired in parallel, are NOT connected to the batteries when they are disconnected from the coach electrical panels.  (The one Vanner whose label I could see is a Voltmaster 60-50M rated at 50 Amps maximum so I presume the other one is the same model.)

With the battery bank connected the relative voltage measurements were as expected, indicating that the Vanners were probably working correctly while the absolute measurements of +25.6 and +12.8 (to the nearest 0.1 VDC) indicated that the batteries were fully charged.

I put the disconnect switches back in the disconnected position and plugged the maintenance chargers back in.  I checked the voltage on the upper and lower battery strands and they were close to the same but not identical.  That was reasonable given that the chargers were independent (electrically isolated) and the upper and lower strands were bridged by Vanner equalizers just minutes before.  Based on my testing it appeared that everything was OK except that I lacked a plausible explanation for why the engine alternator apparently did not fully charge the batteries yesterday on the drive down from Mayo.  I wrote all this up in an e-mail and sent it to Joe, Butch, and Chuck, all of whom have had conversations with me about this over the last few days.

Linda made a humus and onion on rye sandwich and we split it for lunch along with some grapes.  It rained hard while we were eating but the rain did not last long.  After lunch I completed the certification paperwork for our FMCA Freethinkers Associate Chapter.  It was 4:15 PM by the time I was done.  I will get copies made tomorrow and get it in the mail to the headquarters in Cincinnati, Ohio.

I logged in to the Prevost Community website to renew our AITA NAPA discount card but wasn’t sure what to do, so I called Chuck.  He and Barbara were at a wine and cheese gathering and he said he would call me back when he was free.  Linda wanted to go for a walk around the Resort so at 4:30 we headed towards the north end.  This part of the Resort has had a lot of development since we were last here and now has a lot of new park models and large pads for RVs.

We looped around to John and Ali’s 5th wheel but did not see any sign of them so we headed down the main road towards Jeff and Kathy’s site.  Sure enough, John and Ali were there enjoying a glass of wine with Jeff and Kathy.  They offered us some and we accepted and pulled up a couple of open chairs.  We sat and visited until 6:30 PM when we started to get some persistent rain drops.  John drove us back to our coach in his golf cart.

For dinner Linda made a nice green salad and pan-seared tofu with a balsamic vinegar, soy sauce, and sugar glaze with chives.  It was very good and I could easily have eaten twice as much.  After dinner I worked on an article about replacing the bearings in our Aqua-Hot Webasto burner this past winter while we were on Quartzsite.  I got the text finished and inserted/captioned the photos that had been post-processed.  There are more photos to be processed and I plan to finish the article tomorrow and upload it to the Dropbox for proofreading.

I need, and have been looking forward to, a stretch of quiet days with time to work at my computer as I have a lot to do.  I need to update our website and blog, which is almost four months behind, and get back to work on the SLAARC, FMCA Freethinkers, and FMCA GLCC websites.  I also need to finish some articles for BCM that have been “in process” for quite a while, and I need/want to write some new ones.  Along the same lines I need to clean up my BCM folders on my hard drive and in our Dropbox.  That is not all going to happen by the time we leave for Arcadia, but I will do as much as I can.  Once we get to Arcadia we will be spending more time away from the coach exploring southern Florida and visiting with friends.  That means I will be creating lots of new photos and posts but have less time to process them.  Ahhhh, retirement.

 

2015/11/12 (R) Unforced Solutions

When I got up at 7 AM Linda had already left for the bakery.  I had granola for breakfast and made a cup of Stash China Black hot tea.  I went to my office and processed the photo that Byron sent me of him and Betty and e-mailed it to Gary and Jorge at Bus Conversion Magazine.  I then replied to an e-mail from Nancy (& Big Bill).  We met them at Suncoast Designers in Hudson, Florida in April 2014.  They are from Ontario but have a place near Ocala, Florida where they spend at least part of the winter.  I also replied to an e-mail from the Mitch in Florida regarding good places for bus service and forwarded my reply to Chuck.  I cleaned the kitty litter tray and finally got to work on the bus.

A piece of scrap SurePly underlayment used as a spacer/guide for the Porter-Cable oscillating saw to undercut he bottom edge of the side wall panel so it can be removed above the floor tile.

A piece of scrap SurePly underlayment used as a spacer/guide for the Porter-Cable oscillating saw to undercut he bottom edge of the side wall panel so it can be removed above the floor tile.

First up was to finish screwing the down the SurePly underlayment on the floor of the passenger seat platform.  With that done I turned my attention to trimming the switch panel next to the passenger seat.  This panel is just 1/4″ walnut veneered plywood but has both AC and DC switches mounted in a row across the entire top portion.  The added thickness of the underlayment and tile on the floor and back wall of the platform required the bottom and back edges of the panel to be trimmed so it could be installed and removed in case I need to get to the wiring behind it.  I used pieces of underlayment as spacers/guides and trimmed off the edges using the Porter-Cable oscillating saw.  This was the perfect tool for this situation where I could not remove the panel and take it to the shop.

With the panel trimmed and the sawdust vacuumed up I turned my attention to the tile.  After test fitting some pieces to see where the edges would land I decided to tidy up the front of the bus so it would be easier to work.  While that was certainly true it was also a tactic of stepping away from the work and letting solutions float into consciousness rather than trying to force them out.  After several trips to bring things inside the house and garage it was noon and time for lunch, which meant more time to relax and let my subconscious work on the tile layout.  Hummus and sourdough pretzel nibblers made a quick, easy, tasty meal and a cup of Constant Comment decaffeinated tea helped wash it down and warm me up while I worked on this post.

Two scrap pieces of the Armstrong Alterna Luxury Vinyl tile used as feeler gauges to make sure the side wall switch panel will clear the floor and rear wall tiles.

Two scrap pieces of the Armstrong Alterna Luxury Vinyl tile used as feeler gauges to make sure the side wall switch panel will clear the floor and rear wall tiles.

As long as I was taking a break I called Pat/Vickie Lintner to let them know I would be coming through Elkhart tomorrow (Friday) and verify that they would be home in the morning.  That sounded fine to Pat.  I will be picking up an accessory for a Nutone power base unit from them.  We have one of the power bases installed in the kitchen counter of the bus but the blender was the only accessory that came with the bus when we bought it.  Pat and Vickie had a power base in their bus but it broke years ago.  They never replaced it, and don’t plan to, so they no longer needed the accessories and were willing to give them to us.  We got most of the pieces from them at the GLCC Surplus and Salvage Rally back in September but we were missing a critical piece which Vickie thought she still had and eventually found.

After my break I reinstalled the large front trim board on the driver side vertical wiring/plumbing chase that is located on the outside wall next to the back of the driver’s chair.  I don’t recall how I got it out but I could not get it back in.  I ended up trimming off a small protrusion on the lower end and then it went into position without any further difficulty.  It was a small thing, but it needed to be done and it was good to get it checked off my (mental) “to do” list.  When I cannot solve the problem I am trying to solve (tile layout) I try to keep moving and get other small tasks completed.

I took a few more minutes to carefully measure the adjustment needed to the bump out on the passenger side HVAC duct cover and the dimensions for the two new pieces of walnut that will go on either side of the sofa seat.  I brought the old pieces in the house and found the leftover walnut in the garage as I have to take some of it with me tomorrow to Jarel’s cabinet shop in Logansport, Indiana.  I think an hour of my day disappeared between these small, simple tasks.

I continued to ponder the tile layout for quite some time, taking and retaking measurements as I tried to figure out an arrangement that would allow the joints to fall in reasonable places while making sure I could notch around things that go through the floor and avoid having any small pieces.  That is a lot of constraints.  The arrangement I finally came up with had three full 16×16 tiles centered on the landing and into the driver area.  There will be pieces about six inches wide along the fore and aft edges, and the first full tile will also be about six inches back from the edge of the landing (by the entry stairs).  The joints (grout lines) resulting from this placement will continue up the front of the passenger seat platform and result in tile placements on the platform that should work out well.

Linda called at 4:15 PM to let me know she was on her way home from the bakery and was stopping at Kathi’s on the way.  I was done working in the bus for the day so I adjusted the thermostats on the heaters and checked the house battery bank status.  The battery bank voltage was at 25.0 VDC, just slightly down from the 25.2 V level of a fully charged and rested “24 V” lead acid battery (2.1 V per cell x 12 cells in series).  The State Of Charge (SOC) was at 84% and I decided to leave the charger off until Saturday morning after breakfast.  I did have the shorepower turned off for a few hours Wednesday so the refrigerator was running on the inverter for a while but there are no DC loads operating in the coach at the moment and the Magnum remote is showing zero current coming out of the battery bank.  There must be some loads, however, as the battery SOC wound not drop that much that quickly due to self-discharge.  I locked up the bus, went in the house for the evening, and turned on the outside lights for Linda.  Given when she left the office I knew it would be dark by the time she got home.

I took a few pictures throughout the day so I went to my office and off-loaded them onto my computer.  I had an e-mail from Gary at BCM with the latest markup of the PDF for the December 2015 issue.  I proofread my article and highlighted a half dozen things that needed to be changed, using the sticky note feature for the first time to indicate the corrections, and e-mailed it back to Gary and Jorge.

Linda got home about the time I clicked ‘send’ so I wrapped up my desk work and went upstairs.  She had not been grocery shopping this week and wasn’t sure what to fix for dinner so I suggested vegan pancakes.  Fifteen minutes later we were enjoying flapjacks with real maple syrup and cups of hot tea.  Breakfast for dinner is always a treat.  We spent a little time in the living room by the fireplace and then went to the rec room to watch a few TV programs while we doodled on our iPads.  We have been trying to break the habit of watching TV in bed but we finished watching the last show in bed and then turned out the lights.  In a reversal of our recent usual morning routine I have to be up early and Linda does not, but she still fell asleep before I did.

 

2015/09/28 (M) Connected

I was up at 8 AM, got dressed to work, gathered up the laundry, and started a load in the washer.  I was getting ready to grind the beans for our morning coffee when Linda got up.  She did not look at all well, having come down with what appeared to be a bad cold late last night.  But she’s a trooper and washed our breakfast berries, as she does most mornings, and got our granola ready.

Bus work notwithstanding my first task this morning was to figure out what had gone wrong with the thermostat in the main floor hallway of the house.  This is our “main” thermostat; it controls the heat to the living room, entry foyer, hallway, and kitchen/dining room.  It also controls the air-conditioning for the entire main floor of the house.  There is no air supply or return from the basement and the library has its own HVAC system.

I used my VOM to check the voltage at the secondary of the transformer on the furnace, at the input to each of the five motorized valves, and the voltage coming out and going to the five thermostats (four for space heating zones and one for domestic hot water).  Everything looked OK.  I pulled the main thermostat off of the base to check the wiring there.  I also got out the installation manual to make sure I knew what I was checking.

The wiring of the base plate matched the diagram for a 1H/1C-2T system, i.e., one heating system, one cooling system, and TWO transformers.  The manual was also very clear that the common wire had to come from the cooling system transformer.  The voltage from Rc to C was just under 15 volts when I expected it to be ~26V.  All of this pointed towards the air-handler.  I shut off the circuit breaker for the air-handler and reset it but that did not fix anything.  The evidence was confirming my suspicion that something happened while Rebecca was in the attic on Friday.  That meant I was going to have to go in the attic to figure out what it was.

Getting into the attic meant I had to empty the hall coat closet of all of its hanging contents and most of the stuff sitting on the floor and remove the wooden hanging rod, which fortunately lifts up and out easily.  I then had to lean a 6-foot step ladder against the back wall, climb up, and unscrew the 1/2″ piece of foam insulation that we use as a temporary cover until I can fabricate something more permanent (hopefully something that involves a self-storing ladder and hinged, spring-loaded door).

With the cover removed I was able to get my waist to about ceiling height, set my flashlight where I could reach it, and hoist myself up into the attic.  I do not have any permanent/switched lighting in the attic, but I plan to install some at some point.  What I should do is install a hatch in the hallway so I do not have to empty the closet to get into the attic, but that probably won’t happen.  I did this in our previous house and it made working in the attic much more convenient.  Flashlight in hand I crawled the 15+ feet over to the air-handler on plywood set across the roof trusses on a slope.  I was reminded than another attic project will be to rig up a walkway (crawlway) that is level and does not compress the insulation.  The insulation in this attic is a mess and needs to be straightened out, so that is another project for our “to do” list.  But I digress.

When I got to the air-handler I saw a surface mounted switch box on top of the unit partially obscured by one of the flexible ducts.  The switch was in the “Off” position so I flipped it to the “On” position.  I did not see a transformer so I presumed it was inside the enclosure.  I also presumed that Rebecca had either accidental moved the switch while checking/measuring the unit or had turned it off as a safety precaution and forgot to turn it back on.  It did not really matter as the result was the same either way.

I worked my way back to the hatch in the closet ceiling, lowered myself down onto the top of the step ladder, and climbed down.  The thermostat, which is on the wall across from the closet, now had information showing on the display.  The upside to all if this was that I now knew something about our HVAC system and Wi-Fi thermostat that I did not previously know, so at least I learned something in the process.

This thermostat is 7-day programmable model so I set the day and time and then went through the programmed values but could only access the settings for the cooling mode.  I activated the setup menu and walked through all of the settings, changing only one that had nothing to do with the programming.  I finally got out the user manual and saw that I had to select a mode in order to program its schedule.  I manually set temperatures for heating and cooling that would not cause those systems to come on and then programmed the times and temperature set points, four per day for each mode, for all seven days.

Keith showed up late morning while I was working.  We agreed to let the grass go for another week.  It has been dry and a little warm during the day for the last week and the grass has not grown much.  There is, however, a real possibility of rain latter today and into tomorrow.  Also, Phil is supposed to start tomorrow on the French drain and driveway work and with a little luck in the weather department may be done by next Monday.

With the thermostat issue resolved I turned my attention to the bus.  I thought about priming the walls but decided against it.  I would need to move the desk pedestals and bases, unscrew the sofa seat platform and move it on top of the pedestals, and then mask everything with painter’s plastic.  All of that was work that was much more easily and quickly accomplished with two people and Linda was sound asleep taking a nap that she obviously needed.

The other reason for not getting into the priming was that I have to take the bus to Chuck’s shop in Novi tomorrow morning to have the two lower windshields replaced.  That meant the bus had to be ready to move before the end of today and there were two things I had to do in that regard.  One was to reattach the desk pedestals to their bases and to the wall.  The other was to connect the loose ends of the two Aqua-Hot heater hoses together.  It had only just occurred to me that once I start the main engine the Aqua-Hot will heat up and the coolant will expand.  If these hoses are not connected the supply line will have coolant coming out of it and the return line will suck air into the system, neither of which would be good things.

I took care of the desk first.  I reattached each pedestal to its corresponding base using the existing screw holes.  I set the two assemblies in place with the connecting cover and then reattached each pedestal to the wall using the existing screw hole.  I thought about trimming down the temporary plywood top and reinstalling it but decided there was no point in doing that.  I cleaned up the rest of the interior making sure there were no loose items on counters or elsewhere that could fly around while the coach was moving.

The two bleeder valves were still clamped inside an old piece of heater hose that originally connected the two front heat-exchangers together with short stubs of hose on the other ends.  Working in the garage on our temporary workbench I unclamped and removed the hoses.  One of the valves was very badly corroded on one end and was not reusable.  The other one needed to be cleaned up but appeared to otherwise be serviceable.  Some of the inside of the hose was stuck to the metal of one of the pipe ends and was surprisingly difficult to remove.

I washed my hands, which were filthy, checked my e-mail, sent a message to Bill Gerrie, replied to an e-mail from Butch, took the dried laundry upstairs, folded it, and put it away.  Linda woke up while I was finishing the laundry and heated up some Amy’s mock chicken noodle soup for our lunch, which we had with sourdough pretzel nibblers and roasted red pepper hummus.  It was 2:30 PM by the time we finished lunch.  I called Josh Leach at Coach Supply Direct to see if he had followed up with Ferman Miller at Countertops Plus regarding our Corian tabletop.  I got his voice mail and left a message.  It felt like the day was slipping away and I had not done much but I had, in fact, accomplished quite a bit and all of it was stuff that needed doing.

I worked on this post for an hour and then completed the task of connecting the two heater hoses together.  I cut the ends of the old hoses off so I had clean material and square ends.  I slipped two band clamps over each hose and pushed them over the pipe ends of the bleeder valve.  They were very difficult to get on but I got them on far enough to put two clamps on each connection.  I did not turn the Aqua-Hot on as I would rather not refill these hoses with antifreeze at this time but I did start the main engine to air up the chassis and then let it run for 30 minutes to get it up to temperature.  It did not have any noticeable effect on the coolant in the Aqua-Hot in that short amount of time.

While the engine was running I closed the roof vents and made one last check that the interior was secure.  Once I shut the engine off I closed the various air valves, disconnected the batteries, locked up the coach, and was done working on/with the bus for the day.  I changed out of my work clothes and went to my office to edit blog posts from early August and get them ready to upload.

Linda called me up to dinner at 7 PM.  We had vegan cheeseburgers with leftover vegan potato salad and collard greens Cole slaw (inherently vegan).  It was yummy.  I went back to my office to edit more posts but got involved in e-mails from/to Bill Gerrie and Gary Hatt.  Gary sent me the BCM logo he is using for business cards and I spent over an hour trying to use Microsoft Publisher, and then Word, to layout a BCM business card that says “Freelance Author/Photographer.”  I did not care for the result and really want a card with the cover of the February 2013 issue as a full card photo.  The cover of that issue is our bus.

I came upstairs a little after 10 PM and watched the end of NCIS Los Angeles with Linda.  She did some online research and concluded that she did not have a cold but is suffering from an allergic reaction to something.  She went straight to sleep while I played a few games on my iPad before turning out the lights.

 

2015/09/22 (T) Bench Work

Linda scraps the old wallpaper off below the passenger side living room window.

Linda scraps the old wallpaper off below the passenger side living room window.

We were up at 7:30 AM and had fresh grapefruit and cinnamon raisin toast for breakfast.  We turned the fireplace on and drank our coffee in the living room.  After taking care of a few chores we got to work on the bus.  Linda started stripping the old wallpaper while I finished soldering two 45 degree copper street elbows.  I then got my tools out and gathered up supplies I needed to disconnect the fan-coil heat exchangers and heater hoses.

I started by trying to connect a 1/2″ i.d. clear vinyl tube to the drain stub on the Aqua-Hot.  The stub points straight down, is approximately 3/4″ long, and the open end is about 3/4″ above the base.  There is a hole in the base of the unit at that point, provided by Aqua-Hot for a drain line, but Royale Coach installed one of the CruiseAir condenser units directly beneath the Aqua-Hot and did bother to provide a hole in the shelf or make alternate arrangements for draining the unit.  I could not get the vinyl tube over the stub and with a limited amount of time to spend on this minor annoyance moved to Plan B.

We have had a large stainless steel photo processing tray, approximately 2′ X 3′, for years.  Today we used it to catch antifreeze and protect the new floor.  Linda got some scrap towels and we put them under all of the edges of the tray.  I then set the heat exchangers on pieces of 2×4 in the tray to keep them up out of the antifreeze.  Linda held the heater hoses as I undid each of the band clamps in turn and worked them loose from the exchangers.  We emptied the coolant from the exchangers and hoses into the tray, wiped off the heat exchangers, took them outside, and set them in the driveway.

The two fan-coil heat exchangers in the photo tray ready to have the coolant hoses disconnected.

The two fan-coil heat exchangers in the photo tray ready to have the coolant hoses disconnected.

We made sure the hose that connected the two units was drained, wiped it off, and took it outside.  This hose has bleeder valves at each end that I will have to remove as I need to reuse one of them.  We drained the two remaining hoses as best we could and put the open ends in the metal photo tray.  I bought a bucket yesterday with a gasketed lid that has a built in spout.  I picked the band clamps and pieces of 2x4out of the antifreeze and put them in the bucket.  We then carefully poured the antifreeze from the tray into the bucket and put the lid on.  We carried the tray outside and set it in the driveway and then took the bucket outside.

Linda took a break from stripping wallpaper and went to the bank to deposit proceeds from the recent rally.  There wasn’t anything else I could do in the coach and I turned my attention to cleaning up the work surface in the garage.  I took the two desk bases to the garage and started working on the installation of the grates and heat exchangers.  I had not worked through the details of this in advance so I had to figure them out now.  I started with the left base, which has an angled front.

The coolant hoses with the heat exchangers removed.  We were able to contain the coolant in the tray and not get any on the new floor tiles.

The coolant hoses with the heat exchangers removed. We were able to contain the coolant in the tray and not get any on the new floor tiles.

The heat exchangers needed to be spaced up 1/2″ off the floor to better align with the openings in the sides so I cut pieces of 1/2″ plywood to put under them.  The exchangers have two holes on the bottom front edge that were probably created by Royale to mount them.  Actually, it appears that Royale mounted them upside down, presumably to position the coolant connections where they needed them.  I say they were upside down because I discovered labels on the “bottom” indicating they were made by “Vantage Products, Exclusive U. S. Distributor of Primus Hydronic Heating Products.”  I designed the desk bases so that the exchangers would mount the same way Royale had them.  As such they will remain “upside down” but it will not affect their operation.

My plan was to put 3/8″ wide by 1/4″ thick dense foam self-stick weather stripping around the edge of the discharge side of the exchangers to seal them to the base and reduce vibration noise due to the fans.  I cut the 1/2″ plywood large enough to provide room for mounting brackets to attach the plywood inserts to the base in locations that I could reach with the heat exchangers in place.  The exchangers had to be screwed to the plywood before it was set in place inside the base since the grates blocked access to the two mounting holes.

The two fan-coil heat exchangers that will go in the bases under the two desk pedestals.

The two fan-coil heat exchangers that will go in the bases under the two desk pedestals.

By now it was mid-afternoon Keith showed up and mowed the grass so I took a little time out from my work to chat with him.  When I returned to the makeshift workshop in our garage I cut the brass-colored decorative aluminum grates to size and secured them on the inside of the base using small screws.  I also wanted to add a layer of the plastic gutter mesh I bought yesterday.  After cutting the first piece to size I decided to use double stick tape.  The only tape I had was 3M Extreme Duty Mounting Tape so I drove to Lowe’s to get something more appropriate.  I found a 1″ wide clear tape and decided to try it.

Half inch wide tape would have been better so I tried cutting the 1″ tape in half lengthwise.  I removed the discharge grate, applied the tape to the edges on the back side, and pressed the plastic mesh into it being careful to keep it as straight as possible.  I then screwed the whole assembly on the inside of the base.  The screws did not like going through the tape or the mesh so I was quickly disabused of this assembly process and decided to use the tape as it came off the roll.

For the air intake grate I first screwed the metal sheet to the inside of the base.  I then applied shorter pieces of tape around the edges in-between the screw heads.  I carefully positioned the pre-cut plastic mesh, peeled the protective layer off of the tape, and stretched/pressed the mesh in place.

I needed to clean the 3/4″ copper inlet and outlet pipes on the heat exchanger so I got Linda to help me at this point.  She held the heat exchanger as I used a strip of plumber’s sandpaper to remove heater hose rubber that had stuck to the pipe.

Because of the grates on the air openings in the base I positioned the plywood spacer and then marked/drilled the holes for the mounting brackets.  I set the exchanger in place, made several alignment marks, removed the exchanger, and took out the plywood.  I attached the brackets to the inside of the base and then attached the weather stripping to the front of the exchanger case.  I positioned the case and Linda held it while I secured it with two screws.  I slipped the plywood/exchanger assembly back into the bottom of the base and Linda pulled it tight to the front while I secured the brackets to it.  One base done, one base to go.

Keith was done mowing about this time and stopped to see what we were up to and pick up his check.  He normally mows our property on Monday morning but had some service issues with his truck that put him back a day.  He had some string trimming to finish and our dinner was ready so he went back to work and we went inside to eat.  Dinner was salad and Whole Wheat ABC Pasta Veggie Soup.  The soup was a North Bay Trading Company mix that Linda got at Whole Foods.  She added kale and tomatoes to make a very tasty and nutritious dish.

After dinner I was closing up the bus for the evening and noticed that the two large MCD shades in the living room had come loose from their front mounting brackets.  This undoubtedly happened Sunday on Hacker Road as we returned from the rally in Elkhart, Indiana.  Linda helped me move one of the desk pedestals on the sofa so I could get to the shade on the driver’s side of the coach.  Once I could get to it the mounting rail snapped into the clip fairly easily but I will have to figure out why it popped out in the first place and make adjustments if needed/possible.

I checked e-mail and replied at length to one from Gary at BCM.  We then settled in to watch the season opener of NCIS and NCIS New Orleans (NCISNOLA) followed by several shows on CreateTV (PBS).  I multi-tasked, working on blog posts at the same time.

My work yesterday and today was not as physical as what we have been doing for most of the summer so it did not feel like I had done much but the evidence suggested otherwise.  These seemingly small tasks often have a lot of steps that have to be done carefully in the right order and take time to do.  There was also a certain amount real-time problem-solving and a trip to the store in the middle of the work.  I hope to finish the other base tomorrow, get both of them back in the coach, and get them plumbed with the new heater hose.  That may have to wait a day or so, however, as Linda needs to finish stripping the wallpaper in the area behind the desk and we need to hang the new paper before re-installing the desk.  There is a definite order to this work that cannot be circumvented.

 

2015/09/01 (T) Tiling Kate

We both slept until 8 AM this morning and even then got up slowly and reluctantly.  We probably need a day off to rest, relax, and catch up on some not-so-physical tasks, but now is not the time.  There is too much to do and time is slipping by.  The fact that hot weather, muggy weather is forecast for the rest of the week probably had some effect on our enthusiasm for getting back to work.  We should probably get up at 6 AM and quit working by early afternoon, but I am not on a sleep schedule that accommodates those hours.

We had our usual homemade granola with blueberries, split a banana, and had OJ/GFJ to wash down our vitamins.  I made Ethiopian Yirgacheffe half-caff coffee, but not as much as usual.  We enjoyed our coffee in the living room with our cats and finally got back to work at 10 AM.

Dry fit of Armstrong Alterna floor tiles.  The starting point was where the kitchen was where the kitchen transitions into the hallway.

Dry fit of Armstrong Alterna floor tiles.  The starting point was where the kitchen was where the kitchen transitions into the hallway.

Today was one of the milestone days we have been working towards all summer; we (finally) started laying out (dry fitting) the new floor tiles.  I had done two layouts on 1/4″ grid paper back in early June; one with the sides of the tiles parallel and perpendicular to the centerline of the bus floor, the other with the sides turned 45 degrees.  We both liked the turned layout better so I used it to estimate the number of tiles we needed and placed the order back in mid-June.  They took a few weeks to arrive but they have been sitting flat in their boxes since early July waiting to be installed.

My original drawing has tiles lined up with opposite corners on the centerline of the floor, although it looks good on paper there was no way I could draw it at a scale that allowed me to accurately account for the 1/8″ grout spacing.  The drawing was just a “proof of concept” and a starting point for the actual layout.

We laid tiles out according to the plan from a starting point in front of the refrigerator that would allow one of the grout lines to go down the center of the hallway in front of the pantry.  Unfortunately that did not allow the tiles to reach the front edge of the floor by the cockpit or work out well for the toe kick space under the kitchen base cabinets or hallway running back to the bathroom and bedroom.

A famous problem in mathematics is finding convex polygons that can “tile the plane.” What this means is that the polygon can fit together with itself perfectly so that there are no gaps.  Some of Escher’s artwork was based on the use of such polygons and that is the context in which most people would be familiar with this concept.  Among “regular” polygons, which are equilateral and equiangular, triangles, squares, and pentagons can tile the plane.  So can right triangles and parallelograms, which includes the rhombus.  Beyond that it gets a bit tricky and someone just recently discovered a previously unknown irregular pentagon using a computer program to systematically examine a very large number of possibilities.

What does that have to do with our bus remodeling project?  Not much, really, beyond the obvious fact that the new vinyl floor tiles for our motorcoach are squares with an edge length of 16 inches.  Floor tiles are almost universally square in shape because they are easy to manufacture and can be laid out on a floor in several different ways. Finding a way that fits a particular space in a balanced way is the tricky part, however, and more so in this case because the tiles need to form a continuous pattern of grout lines (if possible) while working their way down the hall and into the bathroom and bedroom.

We shifted the string of tiles running down the centerline towards the kitchen cabinets on the driver’s side of the bus so the corners just reached the recessed base.  We then shifted them towards the rear of the coach to get reasonable size pieces at the front edge by the cockpit.  We filled in some tiles to either side of the main fore-aft string to make sure they would make it to the edges with reasonable size pieces.  When it was clear that this positioning was going to provide a balanced installation in the kitchen and living room we started working our way down the hallway and into the bathroom.

The tiles continued to fall into place and fit well in the bathroom but did not flow into the bedroom quite the way we wanted.  We may have to offset a grout line as we transition from the hallway to the bedroom but were otherwise satisfied with our dry fitting.  We returned to the front of the coach and placed every full tile that we could.  We then started trimming tiles to fill in smaller pieces.  We limited ourselves to pieces that had one or two straight cuts and no notches or tabs.

It was 4:30 PM by the time we got to the door of the bathroom and bedroom threshold, where a critical decision would need to be made regarding the offsetting of a grout line.  We have learned that the end of the work day is not a good time to make critical decisions.  With company coming in a couple of hours we quit working and got cleaned up.

I sat in the living room and worked on this post.  Kate sent a text message at 5:30 PM that she was leaving Wayne RESA and heading our way.  We figured she would get here at 6:30 and that is when she arrived.  She brought a dip that she made from cannelloni beans, garlic, and lemon juice, some baby carrots, and some pretzel chips.  We enjoyed the appetizers with some Bell’s Oberon beer while we chatted about work, travel, and family.  Kate travels every chance she gets, usually with her S.O. Brian but sometimes by herself.  Europe is a favorite destination but she frequently visits family members all across the U.S.A. and sometimes overseas.

After catching up a bit we gave Kate a tour of the bus interior.  She liked the new floor tiles and our choice of seat fabric but was suitably impressed with the pull-out pantry which pleased us.  I turned off the three residential air-conditioners as we exited the bus.  Linda then got busy preparing dinner while I showed Kate the pieces of the custom desk and built-in sofa.  I turned on the A-C in the library (where the desk and sofa pieces are stored) to cool it off and lower the humidity.  It had been off all day since we were running the main house A-C plus the three A-C units in the coach.

Dinner was ready at 8:30 PM, a simple but tasty meal of burgers and fries with a second round of Bell’s Oberon beer.  (Linda bought a real beef patty and got a slice of real cheddar cheese for Kate.)  We had fresh strawberries and Coconut Bliss non-dairy ice cream for dessert and then continued to chat about photography, cameras, travel, and the low power Radio station, AM 1700, that Brian runs in Ypsilanti.  A local blogger does a weekly interview show that Brian then podcasts.  The most recent one was an interview with a professor from U of M Ann Arbor who wrote a book that was recently made into a movie (Diary of a Young Girl).  The podcast was “liked” by Sarah Vowel, who is sometimes featured on “This American Life.”  Very cool.

Kate had to go to work in the morning and left around 10:15 PM.  Linda went straight to bed but I had a couple of things to take care of first.  I had initiated the download of an updated NVidia GeForce driver for my ASUS laptop computer.  I e-mailed several documents to my sister Patty, and then downloaded the final draft of the August/September Bus Conversion Magazine, proofread my two articles, and e-mailed a couple corrections to the publisher.   I installed the driver update and then went to bed.  I wrote for a while and finally turned out the light at midnight and fell asleep.

 

2015/08/27 (R) In and Out

Linda was up at 5:45 AM and on her way to the bakery at 6:15.   I got up an hour later and also got an early start to my day; early is relative, after all.  After a bowl of granola I brewed some Cafe Europe / Columbian decaf coffee, turned on the gas fireplace, and continued reading Number Theory and its History.  A week ago Jim (N8KUE) e-mailed some questions to us regarding RVing and bus conversions.  I felt that too much time had passed without a response so I settled in at my computer to answer his questions as best I could.  I sent my reply at 9:30 and turned my attention to our bus project.

I got the pull-out pantry (mostly) installed yesterday.  Before we could place the refrigerator in the alcove, however, I needed to do four things:

  1. Install a piece of aluminum angle to prevent the fridge from sliding to the left;
  2. Secure the water line that went to the old refrigerator;
  3. Plug up openings in the cabinet with steel wool; and
  4. Install the 10th drawer slide on top of the pantry to reduce lateral movement at full extension.

I decided to tackle these tasks in that order, which meant a trip to Lowe’s to get the aluminum angle.  I chatted briefly with Mike (W8XH) on the drive and stopped at The Home Depot first but did not find what I wanted.  Lowe’s had a 3 foot length of 1/8″ thick 1.5″X1.5″ angle.  I wanted aluminum because it is light, easy for me to work, and won’t rust or need to be painted, but I wanted the 1/8″ thickness for strength.  While I was there I picked up another foam brush, a bottle of Mineral Spirits, and a package of #8-1.75″ stainless steel self-drilling exterior wood screws.

The road graders were out today in our part of the county and I passed the one working on Golf Club Road going to, and returning from, Lowe’s.  There was also one working on our road that I could not get around, so I followed it slowly until it reached our driveway and I could turn in.

Back home I cut the aluminum angle to a length of 26.5 inches, the same as the depth of the refrigerator base section and the top piece of plywood in the base of the alcove. I selected a drill bit that was just barely larger in diameter than the stainless steel screws.  Starting with the midpoint I drilled holes every three inches along the centerline of one side of the angle.  I then countersunk each hole, checking with a screw until the head was just slightly recessed.  A light back bore with the countersink bit removed any rough edges.

With the pantry pulled all the way out I placed the side of the angle with the holes on the 2nd piece of plywood in the alcove base with the other side of the angle against the edge of the 3rd piece of the base.  Since these pieces of plywood are all 3/4″ thick the vertical side of the angle extended above the plywood by 3/4 of an inch, more than enough to catch the left side of the refrigerator.  I held the angle tight against the edge of the 3rd piece of plywood, with the front edge back about 1/2″, and used the #8 VIX self-centering drill bit to drill a pilot hole in the back hole.  I then secured it with one of the stainless steel screws, penetrating both the 2nd and 1st layers of plywood and probably a heavy 1/8″ of the subfloor.  I held the front of the angle tight and secured the 2nd hole from the front in the same way, as I could not access the first hole due to the pantry.  I drilled all the remaining holes except the first and put in the screws.  I then pushed the pantry all the way in so I could access the front hole and secured it.  The angle was now held in place by nine strong screws fastened into a lot of wood.

The pantry and refrigerator installed in the alcove.

The pantry and refrigerator installed in the alcove.

The old refrigerator had an ice maker and cold water dispenser in the freezer door so there is a flexible copper water line at the back of the alcove.  The line runs through an inaccessible area and into the cabinet under the kitchen sink so removing it would be difficult and impractical.  It was easier to secure the water line, and besides, we might want to use it again someday.  I found some used screws with broad #2 SR heads and used them to secure cable ties with mounting tabs to the back wall of the alcove.  I re-shaped the copper tube as best I could so it would lie relatively flat against the back of the alcove and used the cable ties to hold it in place.

I noticed when I moved the tube that a little water came out of the end.  That struck me as odd as I had it in my head that the line was out of service.  After a little investigation I remembered that the shutoff valve for this line was still attached to the water inlet tube on the back of the old refrigerator.  If we had pressurized the fresh water system this would have been an open line.  Yikes!

I now had another, unexpected, task that had to be done before I could do anything else.  I gathered up a few tools, parts, and materials, got my head and arms into the under sink cabinet (which is never comfortable), shut off the supply line valves (just to be safe), and disconnected the copper tube to the refrigerator alcove.  I wrapped the threads of the open end of the T-fitting with several turns of Teflon tape, threaded a cap into the fitting, and snugged it up tight.  I did not, however, pressure test it as I did not want to take the time and I did not want to pressurize the fresh water system with the toilet disconnected.

With the water line secured I got one of the old packages of steel wool and used it to stuff the openings in the lower rear corners of the alcove where lots of wires, the water line, and two air lines pass in and out.  I meant to use the #1 steel wool but grabbed the 4/0 by mistake.  It will work just as well but the 4/0 is what Linda is using to clean all of the walnut woodwork, so it was a bit of a waste.

The pull-out pantry is very stable vertically and horizontally except when it is all the way out where it can move side-to-side about 1/2″.  I decided to install the last of the 10 slides on the flat between the top of the pantry box and the ceiling of the alcove, which is also the base of the upper cabinet.  The ceiling of the alcove is not parallel to the floor and so it was not parallel to the top of the pantry box.  I was able to slide a piece of 3/4″ oak veneered plywood between the ceiling and the upper edge of the top slide. With the 10th slide on top of the pantry I had about a 1/8″ gap between the slide and the plywood at the front, opening to about a 1/4″ gap at the rear.

My first attempt at a solution was to try cutting blocks from the end of a 2×4 to be just the right thickness for the front, middle, and rear.  That quickly proved to not be a workable solution without some form of stationary saw.  After further pondering I decided to cut a 4.5″ wide piece of the oak veneered plywood from one of the leftover pieces that happened to be 26.5″ long.

The new refrigerator in the alcove with the doors open.

The new refrigerator in the alcove with the doors open.

I set the piece of plywood in place on top of the two slides, one mounted to the alcove side panel and the other resting on top of the pantry box, and shimmed it with wood shims between the plywood and the ceiling to remove the gap between the plywood and the slide without making it tight.  I pulled the pantry out slightly so I could drill and screw the rear hole of the stationary part of the slide.  I then pulled the pantry all the way out, pushed the center section of the slide part way back in, and secured the front hole of the moveable part of the slide to the top of the pantry.  I used a slot that allowed side-to-side adjustment, just in case.  I also secured the center slot on the moveable slide to the top of the pantry box.

I fiddled with the slide until it went in and out smoothly.  It is tight enough that I don’t think it will come open when driving, but it pulls out easily enough and will be easier once we get a handle on it.  Linda called at 4 PM as I was finishing this task to let me know she was on her way home from the bakery.  It would be 60 to 90 minutes before she got home so I moved on to the next task.

The first piece of underlayment to go in will be a full 4’x8′ sheet minus a notch for the middle air-conditioner drain line and part of one short side that has to fit around the built-in pantry.  I measured for those cuts and then laid the sheet out in the driveway on top of 2x4s (on the flat).  I tried plunge cutting most of the 21″ long by 1″ wide strip off the end with my circular saw without using a guide and finished the cut with my saber saw.  My plunge cut wasn’t very good so I trimmed it with the saber saw.  That edge will go under the mirror tiles against the back of the built-in pantry so it will be OK.

Linda got home around 5:30 PM.  After unloading her car and changing clothes she examined my work for the day and was pleased with the way the pull-out pantry worked.  She helped me carry the 4’x8′ sheet of underlayment into the bus at which point I decided that we needed to get the refrigerator into the alcove before doing anything else.

We set the underlayment aside and uncovered the fridge which we had previously wrapped in painter’s plastic to keep it clean while grinding and sanding.  Linda cleaned off packing tape adhesive with Goo Gone, wiped it off with a wet rag, and then I wiped it off with a dry towel.  We rolled it over to the alcove, shut off the circuit breaker, plugged it in, and secured the cord to the back.  It rolls very easily but to get it into the alcove we had to tilt it forward to get the bottom back edge of the unit onto the 2.25″ high plywood base.  Oops; the left edge of the fridge space overlapped the built-in pantry opposite and prevented the unit from tilting enough to get the back edge up high enough.

The pantry pulled out with the refrigerator installed.

The pantry pulled out with the refrigerator installed.

We have learned not to panic, and after a moment’s thought we turned it slightly to the right, got the right rear bottom corner up onto the plywood and slid it into the alcove a couple inches.  We were then able to turn it to the left and get the left rear bottom corner onto the plywood base, making sure it was inside the aluminum angle.  Fortunately we had enough clearance above the unit to do that.  (If not we would have used the leftover 3/4″ plywood in front of the alcove, gotten the fridge onto those pieces, and then rolled it straight into its space.).   We lifted the front bottom of the unit and rolled it back into its cubby.  It was a perfect fit; snug to the aluminum angle on the left, tight to the right side of the alcove at the rear with a small (3/16″) gap at the right front, and far enough into the alcove that we can open the three drawers to the left of the sink.  High five!  Good job team.

I turned on the breaker to make sure the refrigerator still worked.  It did, and we were both pleased with how much quieter it is than the old one.  We did not need it running at the moment, however, so I turned the breaker off.  Linda got a towel and propped the doors open.

We got the underlayment flat on the floor and slid it into position.  It needed to be trimmed in three spots and I did not want to get into that at this hour so Linda started preparing diner while I put tools and materials away, locked the bus, and closed up the garage/shop.  I plugged in the old refrigerator (in the garage) to let it cool down overnight as DTE Energy’s recycling program is picking it up tomorrow between 8 AM and noon.

Dinner was mock riblets in BBQ sauce, green beans with onions and carrots, and fresh peaches, all very tasty.  After dinner I worked at my desk.  I replied to several e-mails from Gary at Bus Conversion Magazine, and looked at my Habitat For Humanity article to see if I could split it into two or three parts.  It looked like that was possible so I let Gary know.  I chatted briefly with Steve (N8AR) on the Novi 440 repeater and with Jim (N8KUE) on the South Lyon 2m repeater.  I processed three photos of the finished pantry/fridge installation showing that everything goes in and out and e-mailed it to a dozen people.

I came to bed just before 10 PM.  We watched TV for a while until Linda drifted off to sleep.  I stayed up a bit longer to finish this post.

 

2015/08/21 (F) Have Fridge Will Travel

I was up at 7:40 AM and made a pot of Costa Rican half-caff coffee.  Linda was up just before 8 AM and washed off some fresh blueberries to put on our breakfast granola.  The Costa Rican is definitely not our favorite coffee and I brewed it with a little too much water which did not improve matters.  But we bought a pound of beans and are not going to throw them out so the sooner we use them up the sooner we can get something that we like.

Harvey Carter (AC8NO), the current President of our South Lyon Area Amateur Radio Club, agreed to help us move the old bus refrigerator from Chuck’s shop in Novi to our house this morning using his cargo van.  He pulled into the parking lot of the shop right behind us at 10 AM.  Chuck and Barb had already left for Oscoda in their bus with their race car trailer in tow.

After opening the shop we had Harvey back his van up to the overhead door.  We brought several lengths of 2x4s planning to use them under the back of the refrigerator but Harvey had two ramps made from 2x12s with a cross piece that spanned the rear bumper.  That looked like a much better alternative to us.  He also had a good hand truck and a ratchet strap.

We decided to truck the unit from the left side because the refrigerant and water lines protrude beyond the back of the case.  We removed all of the trays from the doors and cabinet but left the shelves in place.  We slid the hand truck under the left side of the cabinet and secured it with the ratchet strap.  With Harvey on the hand truck we tilted it back and rolled it out to the ramps.  We adjusted the ramps so the hand truck wheels would be centered on them.  Harvey then pulled the hand truck up the ramp backwards as Linda and I pushed from the bottom, eventually lowering it all the way down as we slid it fully into the van.  I then closed up the shop.

I rode with Harvey in the van and Linda followed us in the car for the trip back to our house where I had Harvey back his van up to the small garage door.  Reversing our procedure from earlier we unloaded the fridge by rolling the hand truck down the pair of ramps and put it just inside the small garage bay near the door.  We plugged it in and it started running so at least we did not break it.

We wanted to put the drawers and door bins back in but could not get the fresh food compartment door open more than a few inches.  I was able to open it just enough to see inside and determine that at least two shelves had come loose and wedged into positions that prevented the door from opening.  The solution was to remove the door.  I undid the three screws that attach the top hinge to the cabinet and removed it, allowing Harvey to lift the door off of the bottom hinge.  I reattached the two shelves to the mounting rails at the rear of the cabinet.  Harvey then set the bottom door hinge pin back in the lower bracket and held the door while I reinstalled the top hinge.  We will plug it in later next week and let it cool off as it has to be running and cold when DTE Energy comes on Friday to pick it up.

While Linda unloaded the drawers and bins from the car and put them back in the refrigerator I gave Harvey the ham radio tour.  We looked at the antennas on the tower, the cable entry box, and the ham shack with the multiple monitor wall mounted track system we installed.  I then gave him a tour of the bus interior.  Linda was getting ready to go for a walk but I suggested we take Harvey to lunch and agreed to go.  He lives in Green Oak Township southeast of Brighton so we went to the Panera on Grand River Avenue at I-96 as it was in the direction of his house and we all like their food.

After lunch we drove to the frame shop in Howell and picked up the last of four paintings we had framed.  We were pleased with our choice of framing material and the owner, Rick, did a nice job assembling it.  We headed back to Lowe’s and looked at thin paneling materials.  Linda got a shield for the bird feeder that is supposed to keep the squirrels from getting to the seed block and I got a recessed outlet that I am considering using for the refrigerator in the bus.  We stopped at the Walmart adjacent to the Lowe’s but did not find the peanut butter filled pretzels we were looking far.  I needed a battery disconnect for the lawn tractor battery but we did not feel like doing anymore shopping today and returned home.

It was late enough in the afternoon that I did not feel like getting the air compressor out and working on the floor of the bus so I went to my office while Linda went for a walk.  I was going to upload a few blog posts but decided to work on an article for Bus Conversion Magazine instead.

I took photographs of two buses at a pair of converted bus gatherings in Quartzite back in January of this year.  Larry and Carol Hall had a very nice GM4106 at the FMCA Western G.M. Coach rally while Byron and Betty Pigg had a gorgeous Model 15 Eagle at the Eagle International converted bus rally.  Larry and Byron are the presidents of their respective groups and the rallies took place at the same time in adjacent sections of the Quartzsite Marketplace dry camp area.  This campground is near the epicenter of RV vendor activities and only a mile from where we were camped.  Gary Hatt, the owner/publisher of BCM, brought his newly acquired Eagle conversion and had his mobile mechanic drive his MC-9 Moose Creek Motor Cabin, which was for sale.  He invited me over so we could finally meet in person, I could meet a few folks, and photograph the buses.  He knew, in particular, that Larry and Byron were interested in having their buses featured in the magazine and figured I could help make that happen.

I had started articles on both buses right after I photographed them and worked on them a bit back in February but I did not get them finished before we had to leave Quartzsite in early March.  Once we pulled up stakes we were on the move and very busy and I did not get back to them before we got home.  Of course, we got even busier once we got home so new articles for BCM were on the back burner with the gas turned off.  But magazines have lead times with deadlines for each issue, and Gary very much wanted to feature both of these buses before 2016 arrived, so I dusted them off and decided to work on the article about the Hall’s GM4106.

Larry had sent me a brief narrative some months ago and I had started filling in the detailed specifications about the bus and conversion.  I had already selected possible photos for the cover and centerfold as well as the article and post processed some, but not all, of them.  I massaged Larry’s narrative, added an introduction of my own, extracted some additional specifications, and then focused my efforts on completing the post-processing of the photos.

I took a break for dinner and afterwards completed the photo processing.  I then started inserting the thumbnail versions of the images into the Word document and writing captions.  There isn’t really any magic to writing an article; it’s just a specific kind of work.  You string words together into sentences, organized by paragraphs, that tell a short story about something interesting and you illustrate it with captioned photos that are hopefully relevant and technically adequate.  It takes time and energy to do this well, however, and I ran out of both around 10 PM.

 

2015/08/20 (R) On The Level

We awoke around 7 AM and noticed that it had rained overnight.  We had Linda’s homemade granola with fresh blueberries for breakfast, followed by a pot of coffee brewed from the Cafe Europe / Columbian Decaf blend I got from Teeko’s on Tuesday.  As we do most mornings we enjoyed our coffee while using our iPads to check in on the world (Linda) and write about our day yesterday (me).

While Linda went for a walk I checked e-mail and responded to several from Gary Hatt at Bus Conversion Magazine.  I then unloaded all of the boards, slides, battery terminal covers, and the pneumatic disc sander and discs from the car.  I set up our 15 gallon portable air compressor by the entrance door of the bus, got the long air hose out of its storage bay, and connected the air sander.

When Linda got back from her walk we unloaded the pull-out pantry from the car and stored it on top of some of the bookcases in the library.  We had a light lunch after which Linda settled in to work at her desk and I busied myself with sanding the floor in the bus with the air sander.

Floor prep tools: 4” belt sander, hammer and chisel, 4” rotary pneumatic body sander.

Floor prep tools: 4” belt sander, hammer and chisel, 4” rotary pneumatic body sander.

I was eager (anxious) to get the initial sanding done so I could apply the floor leveling compound.  Like drywall compound it will be a multi-day process.  I needed to fill any deep gouges and voids, let the compound dry, and then lightly sand it with an orbital pad sander and finer grit sandpaper to make sure it is smooth.  I then needed to fill the shallow grooves that exist between the ridges of thinset and mastic that I could not sand off completely.  Once that dried I would again sand it off lightly and then apply a final, very thin, skim coat to the entire area, feathering it into the areas where tile was never installed.  Finally I would go over the entire area gently with the pad sander one last time to make sure the surface is as smooth and flat as possible before installing the 1/4″ underlayment.  The tile will be installed directly on the underlayment.

I considered using self-leveling instead of troweled-on floor leveling compounded but decided against it.  Self-leveling is thin, like water, and flows.  As such it seeks its on level and forms a smooth flat surface that is “level” as determined by gravity.  Although it offers the possibility of a single step process with no sanding, it also offers the potential to go wrong and not be repairable.  The bus subfloor would have to be dead level side-to-side and front-to-rear.  There would also have to be a border to contain the liquid and there could not be any holes or cracks that it could leak through.  In particular it seemed I’ll-suited for feathering into the adjacent areas of the subfloor that were never tiled.  And so I decided to fill in and “level” the floor the slower and more labor intensive, but more controlled, way.

For dinner we had the other half of the gluten free pizza Linda made on Tuesday.  We had peaches, strawberries, bananas, and an orange melon that were all ripe so she made a fruit salad.  We finished the bottle of Cupcake Black Forest Decadent Red Wine.

We decided to turn in early and watch a little TV.  Part 2 of The Mystery of Matter: The Search for the Elements was on PBS at 8 PM.  We saw Part 3 last night and did not realize until 7:45 PM that Part 1 was on this evening at 7 PM, so we still have not seen it.

 

2015/08/13 (R) Sanding Success

Linda was scheduled to go into the bakery today but knew before we went to bed last night that the visit was postponed.  That was just as well; we were very tired from our long day yesterday and slept in this morning.

Before I even had a chance to make coffee I spotted wild turkeys by the road in our easternmost driveway entrance.  They walked past the east end of the house into our backyard.  They hung around by the deer block for quite a while so we had a good long look at them and I took a few pictures.  There was a big tom, a younger/smaller tom, and a half-dozen hens, one with a surprisingly small chick for this late in the season.  The turkeys eventually moved on and we got back to our normal routine.  While I made the coffee Linda made her own version of raisin, date, walnut oatmeal with some quick oats that she had in the pantry.  It was very good.

We read for a bit but I needed to finish the blog posts for the last several days and Linda needed to return some items to the Howell Library and run a couple other errands.  While working on the blog post for yesterday I realized that we had not loaded all of the pieces for the built-in sofa.  I checked the pieces we had against the drawings, which we should have done yesterday, and confirmed that we were missing the two top pieces (E) for the support boxes (HVAC plenums) and the top piece (H) for the return air plenum.  I texted Jarel and he replied quickly that he would try to take care of it in time for me to drive back down on Wednesday to pick up them up.  It’s a 12-17 hour, 550 mile day, for me and costs about $60 in gasoline, so hopefully he will have the pantry done by then as well.

Linda got word from our son via TXT message that Shawna’s father, Mick, had passed away.  He had an aggressive but non-cancerous brain tumor that did respond to two separate surgeries and was moved to hospice care about two weeks ago.  Brendan, Shawna, and Madeline are cutting their vacation short by a day to head to the Grand Rapids area but are still leaving Tuesday to fly to Denver to visit Shawna’s mother, Carol, and her husband, Cliff.  It appears that a memorial service may be in the works for the weekend of the 22nd and 23rd, in which case we will probably drive over.

My sister tried to call me today.  Linda was on the house phone quite a bit today with bakery-related business so Patty tried my cell phone but did not leave a message.  I was working in the bus at the time, did not have it with me, and Linda could not find it in time when it was ringing.  Being deaf in one ear she cannot locate where sounds are coming from.  She does a little better when she uses her BAHA, but rarely wears it around the house.  I called my sister back and left a message and she eventually called me back and we got to talk.

Our father, who is 90, had been admitted to a hospital near where he lives.  The staff said he appeared to have severe dementia, but he was fine (for his age) just a couple of weeks ago, so I suspected a stroke or some other sudden change.  Patty sent me a text latter that the CAT scan of his brain revealed two recent lesions (last few weeks), the telltale sign of two strokes.  She also said he was being transferred to Missouri Baptist Hospital, which is much closer to where she lives, for further care.

Those two pieces of news certainly put a damper on the day, and may cause an adjustment in my plans if I have to travel to St. Louis.  In the meantime there is stuff that has to get done, so even though it was warm today and I wasn’t really in the humor, I kept working in the bus, off and on.  I vacuumed up loose material, including inside the bases of cabinets, and then cleaned the wiring in the refrigerator alcove with Lysol.  I decided to make a template for the refrigerator alcove plywood base filler panels so I could cut them the right size/shape on the first try.  I then used one of the new ceramic sanding belts on the residual thin-set and mastic, and it worked!  My sense of hope was renewed that I will be able to install the new floor correctly.

By 7 PM I was feeling drained so I wrapped up my work and took a shower.  For dinner Linda made pan-grilled BBQ tofu with caramelized onions and served it open faced on a hamburger bun with a side of fresh steamed asparagus.  It was delicious.

After dinner I went to Lowe’s and The Home Depot in search of several items but only ended up buying another 36 grit sanding belt.  I needed floor leveling compound but was not prepared to choose between their limited options.  I also needed a self-centering drill bit but neither store had them.  Lowe’s and THD really are focused on the tools and materials one needs to work on a house and its surrounding property.  Things like self-centering drill bits, though useful for things like drilling holes for door hinges, are really cabinet-making tools.  As big as these stores are they can’t, and don’t, sell everything.

I talked to Butch on the drive home.  The self-centering drill bit that Jarel recommended for installing the pull-out pantry slides is a Vix and Butch suggested four places where I could buy it:  Rockler, Custom Service Hardware, McFeeley’s, and Grizzly’s.  Before ordering one I need to e-mail or text Jarel and ask him what size screw I need to mount the pull-out pantry extension slides.

Back home I thought of four other things I could have bought while I was out so I added them to my list.  I then went to my office and worked on blog posts, updated the BCM Group page on RVillage, e-mailed Gary Hatt at BCM, responded to an e-mail from Howard (PlayaDog) re: screens for sliding bus windows, and started downloading Adobe Creative Cloud 2015 updates.  Jack Conrad had responded to my earlier e-mail asking if he knew what was going on with the Arcadia rally and I sent him a reply.  By the time I dealt with all that I was ready to recline and rest.

 

2015/07/26 (N) Rearranging

I was up at 8 AM but did not make coffee as Linda was still asleep and the grinder is fairly noisy.  I put the last load of laundry in the washing machine, cleaned the litter tray (which we keep in the downstairs shower), and then worked in my office.  Jasper (the cat) came down to assist me but mostly ended up supervising.

All three monitors mounted in the ham shack using the ZioTek wall-mounted track system.  The Dell is in the middle.  There is a mount and room for one more monitor at the right end.

All three monitors mounted in the ham shack using the ZioTek wall-mounted track system. The Dell is in the middle. There is a mount and room for one more monitor at the right end.

I mounted the fourth (last) arm on the wall-mounted rail in our ham shack.  I swung it back against the wall to get it out of the way as I do not have a monitor that I want to install at that position at the moment.  I cleaned up the tools and staged them by the stairs and then moved the coiled coax out of the way and cleared a few things off of the desks so I could move the desks back into position.  I left them farther out from the wall than before so they were appropriately placed relative to the three wall-mounted monitors.  I then put various pieces of ham radio equipment back on the desks.

Monitors obviously need computers.  I removed the Dell Precision laptop from my computer desks, removed the computer from the combination docking station and monitor stand, cleaned all of the pieces, and reassembled it.  I set it at the left edge of the ham desks, slid it under the left monitor, and placed our old Icom IC-706 HF transceiver on the monitor platform, just for appearance sake.  We are not using thus radio at the moment but it fit nicely in that spot.

I placed the GoBox with the Icom IC-7000 HF/VHF/UHF transceiver and 12VDC power supply at the right edge of the desks, put the MFJ-998 Intelli-Tuner to its left (under the right monitor), and put the larger variable voltage DC power supply on top of it.  The time we spent yesterday determining where to mount the rail on the wall was time well spent.  The monitors are at a comfortable height for viewing when seated at the desk, tilted down slightly to avoid glare from the overhead down lights, and the bottom edges are high enough above the desk to permit sizeable equipment to slide under them.  The desks are also far enough out from the wall to make it easy to attach and manage cables.

I rearranged my primary ASUS laptop on my computer desks and checked my e-mail accounts.  I have had a discussion going on this past week with Gary at Bus Conversion Magazine about hats with the BCM logo and responded to a couple more of those communiques.  Around 10:15 AM I heard footsteps and knew that Linda was finally up so I wrapped up the work in my office, transferred the laundry to the dryer, and went upstairs.

Linda was working at her desk and was not hungry but wanted coffee.  She did not sleep well last night so I made a pot of Sumatra Manhelding which is NOT one of our half decaffeinated blends.  I got myself a bowl of granola and had a large glass of orange juice.  We spent the rest of the morning in the living room reading, writing, and menu planning.

The dinette area of our bus with the two fan-coil heat exchangers on the floor.  They will go in the bases of the desk when it is installed in this corner.

The dinette area of our bus with the two fan-coil heat exchangers on the floor. They will go in the bases of the desk when it is installed in this corner.

I like to hear the grandfather clock strike 12.   Besides the charming Westminster chimes, it serves to announce that the part of the day has arrived where I am supposed to get some of the physical work on my to-do list accomplished.  Today, however, my #1 priority was to redesign the pull-out pantry so I limited my physical work to gathering up my tools from the basement and moving them to the garage, moving the bus back to its normal parking spot, and taking photos of cabinet details in the bus for Jarel.  I mixed in a little e-mail, a few computer updates, some ham radio, and time for meals, but basically I worked at my drafting board most of the day and evening.

For dinner Linda made a very tasty dish that we had not had before.  The base ingredient was rice and she used basmati even though the recipe called for brown.  I prefer basmati rice to brown rice so it was a good substitution as far as I was concerned.  The other ingredients were garlic, power greens, mushrooms, and blanched fresh green beans.  She sliced and caramelized a large onion and used it as a topping.  This was essentially a “1-pot” dish in that all of the ingredients ended up combined prior to serving.  Linda makes a lot of dishes like this and we both like them. This particular dish had the crunch of the green beans, the chewiness of the rice, and the soft earthy character of the mushrooms held together by the garlic and olive oil and topped with sweet earthiness of the caramelized onions.

At 8 PM local (EDT) I participated in the weekly SLAARC Info Net for the first time in a couple of years and did so from the comfort of our ham shack.  It was a pleasure using our new Yaesu FTM-400DR/DE dual band transceiver with our Diamond X-50N 2m/70cm antenna at a height of 40 feet and connected by good coaxial cables all the way through.  Club president Harvey (AC8NO) served as net control operator and did a nice job.

After the net wrapped up at 8:45 PM Steve (N8AR), Andy (N8DEV), and I chatted for another 20 minutes trying to find some rhyme or reason why our Yaesu FTM-400’s are experiencing random audio dropouts.  We did not get it figured out and wrapped up our QSO so Steve and I could check into the LARK (Livingston Amateur Radio Klub) net that started at 9 PM (EDT).  This was the first time I had checked in to this particular net even though LARK is based in Howell and the repeater is closer to us than the ones in South Lyon or Novi.

The LARK Net was much briefer than the SLAARC net and concluded at 9:16 EDT.  Steve and I went back to the South Lyon repeater where Paul (N8BHT) heard us and joined the conversation.  When we finally wrapped up our testing QSO I went back to work on my pull-out pantry drawings.  I was about to shut everything down at 10:45 PM EDT when Mike (W8XH) announced his presence on the South Lyon repeater.  He was mobile but full-quieting and I did not experience any dropouts during our 25 minute QSO.  I took a few minutes to e-mail Jarel and then called it a night.  I had a few almonds as a snack, got ready for bed, and worked on this bog post for a while.

 

2015/07/07 (T) Field Day Photos

We did not sleep well last night, were slow to get up this morning, and slower to get going.  A cold front was pushing in from the northwest with the promise of cooler temperatures and sunny, blue skies, but first we were in for a day of overcast conditions and rain, which started around 8:30 AM.  It was a perfect morning to sit quietly in the living room, reading, writing, and drinking our coffee but too warm to turn on the gas fireplace logs.

Yesterday Linda started researching RV parks in southern Florida for this coming winter and we spent some time this morning looking at them online.  There was one in particular, Riverside RV Resort and Campground, which caught our attention.  Located on the Peace River near Port Charlotte and Punta Gorda, it is a short distance southwest of Arcadia where the annual Buss’in rally is held.  We went to the rally two years ago and had a great time so we will go again this year if we decide to winter in Florida, which is our current inclination.

One of the reasons for us to winter in Florida, at least occasionally, is our many contacts there.  Our friends, Steve and Karen, bought a mobile home near Venice; our friends, Chuck and Barbara, bought a lot at Pelican Lake in Naples; our ham radio friends, Bruce and Linda, bought a house on 25 acres near Brooksville; our GLCC fiends, Ed and Janet, bought a place that I think is near Sarasota; our FMCA Freethinker friends, John and Marian, bought a place in Dunnellon; and our other FMCA Freethinker friends, Ed and Betty, bought a place in Bradenton.  In addition to all of those folks quite a few of our RV friends, like Pat and Vicki, spend the winter in Florida, and the state has a lot of things to see and do, including one of the best state park systems in the nation.

Linda left for her appointment with the dermatologist and I got to work at my desk.  I continued to deal with e-mails related to the SLAARC domain transfer and an ongoing conversation with BCM publisher Gary Hatt.  I got a Dropbox link to some Field Day photos from Steve (N8AR) a few days ago and downloaded them.  Last night I got a similar e-mail from Mike (KE8AGY) with a Google Drive link and today I got one from Jim (N8HAM) so I downloaded all of those photos.  I spent most of the rest of the day selecting and processing the photos I took and then processed all of the ones I got from other people.

I took a break to chat with Linda when she got back from her appointment.  I then removed the defective Morgan M-302N VHF/UHF Lightning Arrestor from the cable entry box and boxed it up to ship back to Morgan.  I took another short break for dinner, which was an excellent Farro and kale dish, and then worked until 8:30 PM when we had agreed to watch a movie.  This evening’s choice was The Imitation Game, a film about Alan Touring and the concepts he invented that allowed the British to build a machine that broke the coded messages generated by the German Enigma machine during WWII.  I spent another hour at my desk after the movie before going to bed and finishing this post.  Tomorrow morning I plan to finally upload some blog posts and then get back to work on the design of the custom desk for the bus.

 

2015/07/05 (N) Return to HFM

Madeline helps Grandma Linda mix the batter for vegan blueberry pancakes.

Madeline helps Grandma Linda mix the batter for vegan blueberry pancakes.

The day started with Grandma Linda’s fabulous, made from scratch, blueberry vegan pancakes for breakfast, which Madeline helped make!  After breakfast we took Madeline to the Howell Farmers Market (HFM).  She had been to this market with us once before and it was a beautiful Michigan summer morning for a return visit.  On the drive over we discussed why it is that you cannot buy a farmer at a farmers market and you cannot buy a garage at a garage sale.  English can be a funny/strange language.

We walked the entire market, which is not really that big, and Linda bought some fresh strawberries.  A couple of the regular vendors were missing.  In particular we wanted to buy some more soap from Marjorie but she was not there.  Madeline enjoyed checking out the child and doll sized wooden furniture that one vendor had for sale.  We kept an eye out for someone selling jelly beans but did not see any so we stopped at the CVS on the way home and got a small bag of them.

We had just gotten home and I was unlocking the front door when Brendan and Shawna arrived.  We had a nice visit and they stayed for a light lunch.  By the end of lunch Madeline was showing signs of being ready for her nap so Brendan transferred the car seat and stroller from Linda’s car to their car, gathered up all of Madeline’s things, and loaded their car.  Madeline left with her parents at 12:30 PM and Linda laid down for a nap shortly thereafter.

I looked at the SLAARC WordPress website on my iPad to make sure it was working.  I checked most of the pages except for the Member Only Area, which requires a login, and they appeared to be OK.  I then went to my office to deal with things that needed to be dealt with from there.

Madeline tries on a child sized rocking chair at the Howell Farmers Market.

Madeline tries on a child sized rocking chair at the Howell Farmers Market.

My first task was to update the roster and financial records for our FMCA Freethinkers Associate Chapter.  I sent e-mails to new members, uploaded the updated roster to our Dropbox, and e-mailed everyone that they were available.  I had received the draft copy of the June 2015 issue of Bus Conversion Magazine on Friday.  I proofread part 3 of my 4-part article on the exterior renovation of our motorcoach and sent corrections to the editor.  I then settled in to edit blog posts.

I took a break for dinner.  Linda cooked Brussels sprouts and heated some vegan riblets.  The barbecue sauce on these riblets is very tasty.  We had vegan chocolate cupcakes for dessert and they were very tasty too.  I then went back to my office and continued editing blog posts.

I took a break just before 8 PM to join the South Lyon 2m Information Net using our new Yaesu FTM-400DR/DE RADIO but I did not hear anything except noise.  I left the radio on for a while and then turned it off.  I switched the coax to the Icom IC-7000 and turned it on but did not hear anything there either.  I turned the IC-7000 off, switched the coax back to the FTM-400, turned it back on, and went back to work at my desk.  Around 8:30 PM the squelch started opening and I heard very faint voices way down in the noise.  After listening carefully I was able to determine that it was Steve (N8AR) running the net but I could not understand most of what was being said.

It was the first time in a long time that I had tried to participate in the net and I was disappointed that the new installation of the antenna on the tower and coax cables to the radios in the basement was not working adequately.  They were working OK when I tested them with Mike (W8XH) so it could have been an unusual band condition but Steve was obviously getting in from farther to the west than our QTH.  I enjoy operating and am looking forward to finally having our larger tower up and some HF antennas in operation but for now I need to concentrate on getting the VHF/UHF stuff working reliably (correctly and consistently).

I exchanged some e-mails with Gary at BCM regarding the magazine and then continued editing blog posts.  I got through the end of June by 11 PM and quit for the night.

2015/07/04 (S) Another Fourth

Linda was up at 7 AM and grabbed a shower as Madeline is usually awake by 7:15 and up between 7:30 and 7:45.  Madeline tends to wake up hungry so Linda likes to have breakfast ready to go.  I was up by 7:20 and also grabbed a quick shower.  When Madeline was finally ready to get up she let Grandma Linda carry her into the living room and hold her in her arms for a while.  When she was ready to sit up Linda brushed her hair and then Madeline returned the brush to the master bathroom.  Linda got her changed into her day clothes and then we all had breakfast.  Linda and I had our usual coffee, orange juice, and granola with fresh berries plus some vegan sausage links.  Madeline also had the sausage links and berries but her main course was toaster waffles with a little bit of real maple syrup.  Yum.

One of the swans at the Brighton Mill Pond.

One of the swans at the Brighton Mill Pond.

After breakfast Madeline wanted to go look for chickens so she and Grandma Linda went for a walk.  When they got back I learned that they saw three chickens, a duck, some bunnies, and a chipmunk (ground squirrel).  We then read a couple of stories and built a fort in the living room.  We talked about going to the Mill Pond in Brighton to see/feed the ducks but there was some sort of running event this morning, a parade at 10 AM, and then a rubber ducky race at the Mill Pond following the parade.  It is the 4th of July, after all, and most communities have celebratory events going on all day and into the evening, ending with fireworks displays.  That sounded like a crowd to me, with the attendant parking hassle, but we figured the crowd might have thinned sufficiently by 10:30 AM to make the experience a good one and decided to chance a visit.  Linda made PB&J sandwiches and packed some grapes and cookies.

Madeline sitting at a picnic table at the Brighton Mill Pond playscape.

Madeline sitting at a picnic table at the Brighton Mill Pond playscape.

We parked in the lot behind the La Marsa restaurant, which is far away from the Main Street part of the Mill Pond, and walked down the boardwalk to the playscape.  There were a lot of people gathered around the Pond for the rubber ducky race and quite a few children at the playscape with their adult chaperones.  Madeline explored the entire playscape with great enthusiasm.  By the time she was done it was 11:30 AM and she was hungry so we had lunch at one of the picnic tables under the shade of a big tree.

After lunch Grandma Linda stood in line with Madeline to use the bathroom.  We then walked around the Mill Pond and paused to cover our ears while the emergency sirens were tested, this bring the first Saturday of the month.  We had a leisurely stroll back to the car and I had a nice chat with a fellow photographer along the way.  He is a local artist/writer with a deep interest in the Mill Pond and the wildlife that calls it home.  He wrote down his website URL for me: http://Words4It.com.  I checked it out when we got home and it is a valuable resource for anyone interested in the flora and fauna of the Brighton Mill Pond.

The various shades of green with a few orange flowers caught my eye while strolling the boardwalk at the Brighton Mill Pond.

The various shades of green with a few orange flowers caught my eye while strolling the boardwalk at the Brighton Mill Pond.

Back at the house Madeline had some soy yogurt and fresh berries before taking her nap.  I don’t know if she fell asleep and woke up or never completely fell asleep but around 2 PM I heard her fussing.  When I checked on her she said she needed to go to the bathroom.  Linda had fallen asleep but that is a duty she takes care of so I woke her up.  Madeline took care of her business, laid back down, and fell asleep.  Linda stayed awake.

With Madeline asleep I took the opportunity to go to my office and check e-mail.  There was one from Scott at QTH.com indicating that the SLAARC website had been copied to the QTH web servers and was ready for testing.  I think that meant the GoDaddy DNS had been changed to point to the QTH installation but I don’t think the domain name registration had been moved yet.  I will need to clarify that with Scott on Monday.  I also had an e-mail from Gary at Bus Conversion Magazine with the draft of the June 2015 issue attached.  This issue has part 3 of my 4-part article on the 2011-12 exterior renovation of our Prevost H3-40 motorcoach.  I replied that I would proofread it and submit corrections before I go to bed tomorrow night.

Madeline takes the high road and Linda takes the low road on the Brighton Mill Pond boardwalk.

Madeline takes the high road and Linda takes the low road on the Brighton Mill Pond boardwalk.

Although Linda is much more physically active with Madeline than I am I was feeling the need for a nap and laid down at 3 PM.  I heard Madeline get up around 4 PM and I finally got up at 4:15.  Linda enlisted Madeline’s help preparing dinner while I took pictures.  The first task was shucking the whole ears of corn.  Next, Linda let her put them in a large pot of water, add a little bit of sugar, and stir.  While the pot started to heat up on the stove Madeline helped prepare the strawberries by washing them.  Linda then got the vegan burgers ready to grill (inside on our stove top griddle) and prepared the garnishes.  Madeline does not get to help with things that are sharp or hot.  Soon enough it was time for dinner and we all enjoyed our corn-on-the-cob and vegan cheeseburgers. For dessert we had some more of the chocolate cake that we made yesterday with fresh strawberries.

We spotted this young bunny along the boardwalk at the Brighton Mill Pond.

We spotted this young bunny along the boardwalk at the Brighton Mill Pond.

After dinner I cleaned up the dishes and we went out on the deck to sit in the chairs and enjoy a near perfect Michigan summer evening while we watched the bunnies eating grass.  Around 7:15 PM we watched another Sesame Workshop DVD.  This one was on Shapes and Colors.  It was over by 8 PM and Madeline started getting ready for bed which was a very jovial affair.  First the potty, then jammies, then tooth brushing followed by finding blankies, “bebes” (pacifiers), and stuffed animals, all the while laughing and giggling.  Linda finally got her to sit quietly and read her a story which calmed her down enough to go to bed.  If her thoughts drift to her mommy and daddy she will get weepy—it’s part of being two and a half—but we have been successful on this visit keeping her engaged enough to avoid anything more than some occasional brief tears.

Madeline washes the strawberries.

Madeline washes the strawberries.

We split the remainder of a bottle of Leelanau Cellars Winter White wine we had opened some time ago but had vacuum sealed and it was still fine.  Linda finished the dishes and loaded the dishwasher while I filled in the day’s details on this blog post.  Both cats came out of hiding and sought our attention.

We have been hearing fireworks, and/or gunfire, for many weeks now and today was no exception.  Two nights ago someone in the neighborhood was firing off, or shooting, something until well after midnight.  There were more fireworks tonight, as expected, and the activity intensified after 9 PM as dusk gave way to night.  The cats were not completely relaxed about the noise but seemed to tolerate it.  As far as we know Madeline slept through all of it as she is a very sound sleeper.

 

2015/06/08 (M) Home for a While

It rained until well after midnight last night.  The rain was not steady but more in the form of heavy downpours associated with thunderstorms.  The gutter along the rear of our house was not able to handle the volume of water and it was spilling over onto our deck making a sound that we are not used to.  I noted that I should check the gutters for clogs at the downspouts today.  My phone chirped, which meant I had an e-mail, and I presumed it was from our whole house generator.  When I got up this morning the clocks on the microwave and range were flashing “2:06”, so my first thought was that we must have taken a power hit then, but the messages on my phone indicated that utility power had been lost and restored around 3:45 AM; at least that was the date/time stamp on the e-mails.  I got up just before 6 AM and finally figured out that the clocks probably reset to 00:00 when the power blipped (3:45 AM + 2:06 elapsed time = 5:51 AM).

I sat in the living room writing with my iPad and playing games until a little after 7 AM and then made coffee, which got Linda out of bed.  We had planned to empty out more of the bus today but the weather was gloomy and we were tired from the rally so we had a long, leisurely morning before busying ourselves with inside chores.  Linda worked at her desk and I wasn’t in the humor to work downstairs in my office so I set my computer up on the dining room table.  Other than an occasional trip to the bus or the garage I mostly sat in front of my computer and talked on the phone all day.

Linda called Alchin’s, our regular trash collection company, to see if they would pick up the old RV furniture.  They do not have a special truck they can send and could not take the steel furniture even if they could get it into their garbage truck.  Linda suggested we find a company like “Got Junk” and searched online for one in the area.  We decided to call “Chuck It Junk Removal” as they are located relatively close to our house.  Keith, from Kish Lawn Care, showed up around 11 AM to cut the grass and Brad, from Chuck It Junk Removal, showed up around 12:45 PM to look at the furniture and flooring we pulled out of the bus and give us a quote on the cost to haul it away.  As Keith was finishing mowing the grass dark clouds were rolling in from the west and not long after he left we had more rain, although nothing like last night.

My dentist thinks my current intermittent teeth issues are the result of clenching my teeth at night so I made an appointment to get fitted for a mouth guard to wear while sleeping.  I also got hold of Phil Jarrell and he decided that tomorrow morning at 8 AM would be a good time for him to stop by and take some elevation readings for the driveway extension and a French drain for the far west end of the property.  Besides the obvious economy of having him do both jobs while he is on site, we need a place to put the topsoil he will dig out for the driveway and we need topsoil to fill in low spots on the west end of the yard.

I managed to finally get some orders placed today.  The big one was for a SureCall Fusion5s multi-band cell phone booster (transceiver) system from Cellular Solutions in Mt. Pleasant, Michigan.  The other was for a window seal from Prevost.  This is not the seal that holds the glass in the frame but rather a large rubber part that seals the space between the window frame and the structure of the coach.  We may need to unlatch the large fixed window on the passenger side and use it to get the old refrigerator out and the new one in.  This window frame has not been opened since we bought the bus and may not have been opened for many years before that, possibly not ever since the bus was built.  I want the new seal on hand in case the current one gets damaged trying to open the window frame.

Besides these two purchases I talked to someone at A-1 Upholstery and described our home made sofa plans.  She suggested that we would need ~9 yards of 54″ wide material for the sofa seats and back cushions.  I sent an e-mail to Josh at Coach Supply Direct reminding him of some things we had discussed at the rally last week and Rick Short at Isringhausen with questions about their 6800 series bus driver seats.  I also finally got to talk to Mike at Suburban Seating in New Jersey.  As I suspected we cannot buy the seat directly from ISRI, but I may be able to order it through Suburban Seating and pick it up from ISRI USA in Galesburg, Michigan.  That would be much nicer than having it shipped to our house on a truck from New Jersey.

I called Rupes/Cyclo to try to get answers to a few questions about the Cyclo 5-Pro Mark II Dual Head Orbital Polisher and its various pads but could not figure out how to talk to a real person.  I submitted the online Contact Form with my questions and got a speedy reply from Cory as a result of which I now know what to order.  All I have to do is figure out how many of each thing I need.  The Cyclo 5 is available on Amazon Prime, by itself, but it did not appear to be the Mark II model.  Some of the major distributors claim to give you a set of “free” ProGuard Orbital Backing Plates, but the Rupes/Cyclo website clearly states that the polisher is not sold without one of the three head options.  I prefer not to patronize businesses that misrepresent their offerings and will probably order the polisher, pads, and chemicals directly from Cyclo even if I am paying MSRP.

I got a call from Gary Hatt at Bus Conversion Magazine.  I had not looked at or replied to e-mails in over a week and he wanted to make sure everything was OK.  While we were talking we got a call from Curtis Coleman of RVillage so Linda took that initially until my other call was concluded.  I had e-mailed Curtis earlier in the day and he was responding to that communique.

Somewhere in the middle of all that we had chickpea salad on a bed of greens for lunch.  Linda then went for a walk, met Chris (K8VJ) at Lowe’s to pick up some SLAARC mail, and roasted vegetables for our dinner when she got home.  I sent Chuck Spera a short e-mail inquiring about how to open the latches on our emergency escape window and then called it a night.

 

2015/04/26-30 (N-R) Routine Returns

2015/04/26 (N) Bentley

Turning the lights out at 11 PM last night meant I would be awake around 6 AM this morning and ready to get up, and that was the case.  Linda was awake by 6:30 AM and we were up shortly thereafter.  I was able to light the natural gas fireplace without difficulty.  The only thing I can figure is that perhaps I did not have the Off/Pilot/On gas valve in the right position last night.

With the gas valve in the Off position gas cannot flow beyond the valve.  In the Pilot position gas can only flow to the pilot flame assembly, and only while the knob is pushed in, until the flame has been lit long enough to cause the heat sensitive pilot valve to remain open at which point the knob can be released.  I do not think gas can flow to the main burner tubes, however, until the knob is turned to the On position.  There is also a Remote/Off/On switch that has to be in the Off position when lighting the pilot flame (with the built in spark igniter) and moved to the On position to allow the main burner tubes to receive gas.  All I can figure is that I did not have the Off/Pilot/On valve turned to the On position. The Remote position is intended to be used with a wall mounted thermostat which we do not have.  For us the firelogs are primarily decorative but are useful for taking the chill off of the early morning or late evening.  We never have them on, however, unless we are in the living room or dining room where we can see them.

Linda fed the cats while I made coffee which we enjoyed in the living room by the firelogs.  It was 33 degrees F outside this morning but in another week the morning temperatures should be such that we can sit on the rear deck and enjoy our morning brew out there.  We finally both got dressed and Linda heated an Amy’s Breakfast Scramble and split it between us.  We lingered a while longer in the living room and finally got to work on our various chores.

Linda’s focus was to continue cleaning the kitchen, off-loading food and kitchen supplies from the bus, and getting her domestic and professional domains back in order.  She made a grocery list as the day went along.  We would normally go to the Howell Farmers Market on Sunday morning, but the outdoor market does not start until next week.

I cleaned the cats’ litter tray, which seems to be my job at home but Linda’s job on the bus, and then got to work on revising the draft survey for the FMCA national education committee.  While I was doing that I also started up a couple of our workstation computers, installed updates, and kept an eye on my e-mail and RVillage messages.  I worked on the survey until dinner time, with a break for lunch, and had Linda proofread it before I uploaded it to my Dropbox and e-mailed the link to the committee.  We have a telephone meeting at 3:30 PM EDT tomorrow and I wanted everyone to have a chance to look it over in advance of the meeting.

Linda made Farro with garlic, dried cranberries, almonds, and kale and cooked some fresh asparagus.  A green salad and a glass of wine completed a very nice meal.  Linda had a text message from her sister letting us know that her housemate, Linda, decided to have Bentley put down.  He was the oldest of her three dogs, deaf and arthritic, and on medications that he would not take, and he had lost interest in food.  We had both received a text message from Linda regarding our recent visit so I responded to that.  We were sad that Bentley was gone, but glad that we got to see him one last time.

I turned my attention to editing photos for my April 10 blog post about out visit to Bandolier National Monument and Santa Fe, New Mexico but the batteries in my wireless mouse needed to be recharged so I plugged it in and called it quits for the night.  Linda was watching the first episode of Wolf Hall (PBS) on her iPad so I finished reading the May-June 2015 issue of the Gypsy Journal and played a few rounds of my favorite games.  Linda prepared some fresh berries for dessert and we enjoyed them to the glow of the firelogs before going to bed.

2015/04/27 (M) Caller #9

After coffee and cereal this morning I continued selecting and processing photos from our April 10 visit to Bandolier National Monument and Old Town Santa Fe.  I ended up with 16 photos so I uploaded the post and put them in an image gallery at the end.  After lunch I got all of my documents in order for my 3:30 PM (EDT) telephone meeting of the FMCA Education Committee.  I chatted briefly with the committee chair to see if there were any surprises in store.  I then worked on consolidating my draft blog posts for April 11 through 15 which included the time we spent in Norman, Oklahoma visiting with my uncle Bob and Aunt Helen, and four additional generations of relatives.

I exchanged e-mails with BCM Publisher Gary Hatt and Editor Dave Rush regarding my article on the redoing of the exterior of our coach.  The article is 5,800 words with 71 photos and they would like to split it up and run it in installments over three or four issues.  That will require me to go back through the article and identify the places where it can be split, making sure the photos track with the text, and write some additional bridge paragraphs to wrap up each installment and introduce the next one.

I dialed in to my FMCA meeting just before 3:30 PM.  I was caller number nine (9) but I did not win anything.  The meeting lasted almost 90 minutes.  We discussed the survey we have been developing and approved a motion to pass it along to the Executive Board with the recommendation that it be sent to a random sample of the members both electronically and via USPS.  I expect to receive minor corrections in the next 36 hours and get a final draft to the FMCA Executive Director on Wednesday so he can have it reviewed by an outside expert (Barry) at Membership Corporation of America (MCA).  The FMCA executive board meets in a week so we will see what happens.

After the meeting I finished working on the April 11-16 consolidated post and uploaded it to our personal blog just in time for dinner which featured taco bowl salads.  She started with refrigerated tortillas, draped them over ramekins, and baked them to create the shell.  She reconstituted an ancho, red Hatch, and pequin chile and used them to season the pinto beans, mixed greens, tomatoes, onions, and olives that made up the filling.  Franzia Fruity Red Sangria went nicely with the tacos.  Later we had a fresh mixed fruit salad of blackberries, blueberries, strawberries, and bananas.  We relaxed for a while, reading and playing games, but were surprisingly tired and went to bed before 10 PM.  Change happens, transition takes time.

2015/04/28 (T) And now … the rest of the summer

As sometimes happens when we go to bed early, we slept in this morning and did not get out of bed until after 8 AM.  It is nice to be able to do that if we want to.  Coffee and toast got the day started followed by reading, writing, and cat admiring.  It was a beautiful, sunny morning albeit still on the chilly side.  In other words, another day in the idyllic paradise we call retirement in the country.

We have both been busy since we got home last Friday, unloading the bus and putting things in their place in the house, visiting family, cleaning and stocking the kitchen, going through mail, and working on bills and accounting, both personal and organizational.  And that was mostly Linda!  I helped with some of that but was mostly focused on finishing a draft survey for the FMCA education committee, sending it out, and participating in a committee meeting by teleconference yesterday afternoon.  I will have some minor additional work to do on the survey by the end of the day tomorrow, but with the meeting behind me I can now concentrate on all of the other things that need to be done.  To paraphrase Paul Harvey “And now … the rest of the summer.”

One of the chores that is always there is laundry.  Linda seems to take over this task when we are living in the bus, but it is definitely my job when we are at home.  Ditto for cleaning the cat litter tray.  To be fair, both the laundry room and liter tray are in the basement where my office and the ham radio shack are located, so I am down there a lot more than her.  When we first return home after being away for an extended time there is a lot of laundry to do.  Not that we don’t do it while we are away, we do, but I like to clean everything that we had with us.  This is not a one day task, in part because we like to limit the number of loads of laundry we do on any given day so as not to overload the septic tanks, and in part because I just do not want to spend an entire day doing laundry.

My main focus this morning, however, was to revisit my article for Bus Conversion Magazine on the renovation of the exterior of our bus back in 2011/2012.  It needs to be split into 3 or 4 installments and I would rather do that myself, making sure the photos track with the text.  I started a load of laundry and then got to work, keeping an eye on e-mail and RVillage.  I finished restructuring the article just before lunch, uploaded it to my BCM Dropbox folder, and e-mailed the editor and publisher.  Linda reheated the Farro-cranberries-almonds dish for lunch and served it with black grapes.

I moved the first load of laundry to the dryer, put a second load of laundry in the washing machine, and started compiling my posts for April 16 through 20.  I got an e-mail from Lou Petkus regarding the SKP Photographers BOF website.  Lou started, and leads, the BOF and administers the website while I take care of the RVillage group and someone else takes care of the member database/roster.  He found and installed a free system for displaying photo albums.  He was setting it up so each BOF member had their own login and could upload their own photos and wanted me (and Linda) to try it out.  I did, and found a number of issues which I documented for him.  I like the idea, so I hope he can resolve the issues.

I folded and hung up the dried laundry and returned to my blog post which I uploaded, tagged, and published before going upstairs.  It was a beautiful day and while Linda was outside on the rear deck reading four deer walked up the eastern boundary of our property.  We were chatting back there when the doorbell rang, which is unusual for us.  It was Aaron, one of the kids (teenager?) from the house to our immediate east.  UPS had delivered our Amazon order to their house instead of ours even though it had my name and our address on the label.

Linda sautéed onions until they were partly caramelized, pan-fried tofu slices, and then added bar-b-que sauce.  She served these in tortillas rather than on buns.  She also sautéed fresh green beans.  I opened a bottle of Barefoot Moscato and we each had a small glass with dinner.

After dinner I called Joe Cannarozzi, the mobile mechanic who has done the majority of the service work on our bus since we got it back to Michigan in 2010.  As planned, he is now in upstate New York where he will be working well into the fall.  He plans to be back this way the first week in November and we made plans to have him do the routine chassis maintenance at that time.  I also discussed our interior renovation plans for the bus and got some tips from him about how to approach that work, especially the floor, as he has done several.

I noticed that I had a voice message from Gary at BCM.  He had called earlier in the day after I had uploaded the new 4-part version of the Exterior Makeover article so I called him back and left him a message.  Tag; you’re it.

2015/04/29 (W) Bus Lunch

We had a typical start to our day; coffee, breakfast, and iPads (news, weather, games, reading, and writing).  Actually, that’s how most of our days in the bus also start, so the only real difference is where we are sitting and what we can see from that vantage point.  I needed to order a refill on a prescription medication so I tried doing that on my iPad.  No problem iPad-wise, but the Michigan Public School Employees Retirement System (MPSERS) had switched the mail order prescription drug service from Medco/Express-Scripts to Catamaran Home Delivery effective January 1, 2015.  Catamaran was already the third part administrator (TPA) but was now operating their own pharmacy.  Even though I already had a Catamaran account I had to register for Home Delivery service.  Once I did that I was supposed to be able to see any prescriptions that had transferred over.  There weren’t any 🙁  That meant I needed a new prescription.  I had a mid-morning appointment and did not want to spend time “holding for the next available representative” so I decided to take care of this task tomorrow.

Linda called last Friday and arranged to have our curbside trash pickup resume this week.  Wednesday is trash pickup day, so the trashcan had to go out by the street this morning.  (We don’t have curbs here, so I can’t say we took the can to the curb.)  The last two years Alchin’s has come past our house around noon.  While we figured that would probably be the case again this year we did not want to risk missing the truck, so Linda took it out early.

Linda is the treasurer of SLAARC, our local ham radio club based in South Lyon, Michigan.  The club’s bank (First Merit) is there and she needed to make a deposit.  I was headed that general direction so I took it with me.  The deposit made, I headed on to Chuck Spera’s bus garage in Novi, MI.  Chuck and Barbara have the same model Prevost bus that we do only one year newer and converted by Liberty, so fancier than ours.  Like us, they spend a lot of time in it, and, like us, there are always projects to be done.  Some of those, in turn, require some discussion.

I met Chuck at his shop at 10:15 AM and had a look at his turbo boost sensor intake manifold pressure hose.  It appeared to be intact but old a frayed like mine was.  The one on our bus failed on the drive out to Quartzsite, AZ in December 2014.  Changing his hose would be more difficult than our as is chassis batteries are in the passenger-side engine bay and make access to that side of the engine much more difficult than in our bus.  We have been using the same mobile mechanic for the last few years but he has found longer term employment and cut back on the mobile servicing of Prevost chassis.  I indicated to Chuck that we really needed to find someone locally who is in business at an accessible location and plans to continue as such into the foreseeable future.  He suggested that we take a drive to Johnie’s in Walled Lake, so that is what we did.

Denny was not there (Johnie was his dad) but I got to see the place and now know where it is.  We drove back to the Panera in Novi for lunch and then back to Chuck’s shop which is nearby.  By 2 PM we had not only solved all of the world’s problems we had made good progress on unraveling the mysteries of the universe.  Wanting to leave something for the next conversation I headed for home leaving Chuck to ponder the mysteries of the bus, which are far more baffling than the mysteries of the universe.

I drove home on Grand River Avenue (GRA) to avoid WB I-96 and the I-96/US-23 interchange construction.  I bought gas at the Wixom Meijer’s and found out 20 minutes later that I had paid way too much for it ($2.59/gal).  The BP station in Brighton had regular for $2.29 and the Shell station closest to our house had it for $2.44.  Bummer.  I passed a First Merit Bank on the south side of GRA just west of Old US-23 in Brighton.  Not right around the corner from our house, but a lot closer than South Lyon.  There is also a Jeep dealership there.  We are interested in getting a Jeep Wrangler Unlimited, we just don’t like the prices we are seeing.

Our Amazon shipment arrived with the two filter cartridges for the under sink housing in the bus and other things.  Hopefully the delivery to the wrong address on Monday was a one-time thing.  I had been trading phone messages with Gary at BCM and finally got through to him this time.  I then curled up with the new B&H catalog which made it feel like Christmas in April.

Linda made a potato lentil ginger curry for dinner and it was very good.  I had planned on revising the FMCA Education Survey and sending it out this evening but I was simply not in the humor to go back downstairs.  I think my retirement motto is going to be “there is always tomorrow, and if not, it didn’t matter anyway.”  Linda had to get up early tomorrow morning to beat the traffic headed into Detroit so we went to bed earlier than usual.

2015/04/30 (R) Steel

Linda set her alarm for 5:45 AM.  The purpose of her alarm is to wake me up so I can wake her up.  It worked as planned and she got up and got ready to go to the bakery while I went back to sleep.

I finally got up at 8:30 AM.  I’ve been busy since we got home but also a bit tired and feeling the need to just unwind from our exciting winter out west.  After breakfast I called the Internal Medicine clinic at the Henry Ford Health System Columbus Center in Novi to see if I could get my doctor’s nurse to get my doctor to write me a new prescription for my nasal spray.  Naturally I never got to talk to the doctor or a nurse, but the youngish sounding lady who handled the phone call was very helpful, up to a point.  She really wanted to schedule me for an appointment and was not quite piecing together that my prescription, which is for a maintenance drug, is only good for one year but my doctor only needs/wants to see me every other year.  I don’t expect the new script to be a problem, but that fact that my MPSERS health care plan changed mail-order prescription providers as of January 1st may add a wrinkle.  I’m not due for a physical until the fall but I will go sooner if needed to get my script.  Which reminds me, I need to schedule my annual appointment with the dermatology PA.

I focused on making some last minute corrections to the FMCA education survey and shipped it off.  I got an e-mail back from Diane Wolfe with some questions.  She is not a member of the FMCA education committee but she and husband Brett did review and comment on it.  The questions were interesting and answering them gave me a chance to explain some technicalities and cc: the FMCA Executive Director as they were as much for his benefit as hers.

I had several e-mails back and forth with Kate regarding productions at Meadowbrook Theater and an exhibition at the Detroit Institute of Arts (DIA), all of which sounded interesting.  Our social life is less active at home than on the road so we welcome such opportunities.

I had a phone call from Mike at Rocket Steel Buildings following up on an inquiry I made.  He sent me a brochure and a price.  It was something but not exactly the quote I was looking for.  I still need to follow up with SteelMaster Building Systems and get to work on drawings for the wood-framed basilica design.

I compiled my blog posts for April 21-25, 2015 after finding the one for the 24th.  I had e-mailed it from my iPad but it never arrived.  I e-mailed it again and it bounced back.  The spam blocker even said it was from a white listed sender (me!) but rejected it anyway.  Huh ???  I sent it a third time to two addresses, one of which was not attached to our domain, and it came through to both accounts, naturally.  I guess this was one of the mysteries of the universe that Chuck and I left unsolved yesterday.  Anyway, I finally got it, finished compiling my posts, and uploaded, tagged, and published it.

I also had several e-mails back and forth with Lou Petkus regarding the SKP Photographers BOF and website.  Gary sent me a link to a document in his Dropbox with photos and audio files from an interview he did for a featured bus article that never got written.  I agreed to take a look at it and see what I can do.

I managed to get more things off of the bus, including bedding, and did two more loads of laundry.  I do not like to do more than two loads a day as it over taxes the septic system.  Someone rang the front doorbell, the second time this week.  This time it was Kaylie, Aaron’s sister, from next door.  For the second time this week UPS delivered a package, correctly addressed to me, to the wrong address.  I was concerned this would happen and Linda said I was a pessimist.  Apparently we were both right.

I called the local UPS store but the only thing they could do was give me the national 800 customer service number.  I am a pessimist (just ask Linda), so I was not looking forward to that experience, but I called and fought my through their voice menu system.  It did not include an option for my situation (of course) and I finally just kept saying “agent” until the system gave up and connected me to a real person.

“Chelsea” was apologetic, even though she had not personally done anything wrong, because that’s what customer service people are trained to do.  I think someone, somewhere, once upon a time figured out that apologizing diffuses customers who are upset.  Well, it doesn’t.  And assuring me that it “won’t happen again” is equally meaningless when it comes from a person who is not in a position within the organization to make such a statement.  But Chelsea verified my name and address and the incorrect delivery address and said she took careful notes and would make sure they got to the right person.  I hope so.

What is perhaps most frustrating is that UPS has a local distribution center in Howell, and I have the address, but it is not open to the public except for limited package pickup hours.  In other words, the mistake is being made by a driver who is most likely operating out of that location, or by someone scheduling the routing, but there is no customer support person or facility manager that I can talk to, face-to-face, and resolve this at the point of origin of the problem.  We buy a lot stuff now through Amazon Prime, and it all gets shipped via UPS, so having it delivered anywhere other than to our house is a problem.

Linda called at 4:30 PM to let me know she was leaving the bakery at 5 PM and heading to Kathi’s.  They were going to have dinner at La Marsa in Farmington Hills and give the I-96 traffic a chance to subside before she finished the drive home.  I had some of the leftover potato barley ginger curry for dinner and then called Phil Jarrel to remind him that we are still trying to figure out how to put up a bus barn and still want him to do the site prep and driveway.  I then called Butch to see if he was able to locate the front brake drums for their MCI MC-9 NJT bus.  He was, and already had the driver side front reassembled.  I responded to a couple of e-mails and filled out an online RFQ for SteelMaster Building Systems and went to bed.

 

2015/02/24-28 (T-S) Bus Projects

2015/02/24 (T) Little Bus Projects

I went to bed early (for me) last night but slept in until almost 8 AM.  It was cool in the coach and I had cats snuggled up with me enjoying the warmth of the electric heating pad.  When I finally got up I tended to their needs—food, water, and litter—and then tended to mine; fruit juice, granola, coffee, and grapefruit.  It is Tuesday, which is trash collection day, so I gathered up the trash from the kitchen and took it to the refuse container by the curb.  We will only have one more trash collection while we are here and that will likely occur after we have pulled out on Tuesday March 3rd.

I finished up yesterday’s blog post, got dressed, and got to work on my bus projects.  I started by wiping off the spotting on the windows and body from the recent rains.  I thought the reason I spent 40 hours cleaning and waxing the body was so water would run off if it but apparently I was mistaken.  I had also noticed that the wax on the passenger side of the bus had not been fully rubbed down.  I started working on this but without using additional water it just made it look worse so I quit somewhat disgusted with the whole situation and got to work on other stuff.

First up was the dashboard instrument lighting.  For the turbo boost gauge I made a 5 inch extension lead with red #14 wire and insulated female spade connectors on each end to connect to the +24VDC supply wire for the old gauge.  I made a similar lead with black wire for the ground but only put a connector on one end to attach to the new gauge bulb holder.  I used a crimp style speed connector to splice the free end into the existing ground wire which had a fork connector on the end that I did not want to cut off.  I put one of the 24VDC wedge base bulbs in the holder and snapped it into the gauge.

I undid the retaining ring on the speedometer and pulled the instrument out the front of the dashboard.  I thought I had wired the two light bulbs in series to use 12VDC bulbs on a 24VDC circuit but discovered that they were already wired in parallel.  I pulled the two bulb holders out and the bulbs were discolored as if they had been too hot.  I could not determine the voltage rating on the bulbs so I replaced them with 24V ones.  I reinstalled the speedo into the dashboard and put the dashboard cover back on.  I will test the lights the next time I connect the chassis batteries.

I next considered replacing the MAC valve that controls the air shutters for the two A-C compressor/condenser units in front.  I looked at the existing valve and decided to hold off until I could talk to Butch.  He and Fonda had taken off for the day, so that would have to wait.  The valve has a diagram on it that indicates how it operates but I was not completely clear on how to read it.  When I built the new air panel I used identical replacement valves and plumbed them the same as the old ones.  I searched online for “pneumatic valve symbols” and got all kinds of sites.  One of them had a 25 slide presentation on ANSI standard symbols and schematics so I downloaded and studied it.  With my new knowledge I was able to verify that the valve was, in fact, installed correctly.  I figured it was since it seemed to work correctly (until it failed) but it was nice to know for sure.  I am not certain that the three control switches are wired correctly, however, but that is a different project for a different day.

I really did not want to change the entire valve.    I bought the replacement valve from Hei/Tek in Phoenix so I called them for technical support.  They confirmed what Butch suspected; the operator (solenoid) can be changed without replacing the entire valve.  They had a defective valve and offered to take the solenoid off and mail it to me for no charge.  Deal.  I should have it tomorrow so I deferred any further work on this project until the part arrives.

By now it was time for lunch so I made a nice sandwich with toasted sourdough bread, vegan deli slices, Daiya havarti style vegan cheese with jalapeños, lettuce, onions, pickles, veganaise, and honey mustard.

Next up was mounting the turbo boost sensor.  It was a beautiful, sunny day but rather cool so I put on one of my long-sleeve flannel work shirts.  Hey, who said the desert in the winter was paradise?  Oh yeah, I did.  I knew this was going to be an annoying little project and it was.

The turbo boost (intake manifold pressure) sensor is a small rectangular part about 1″ wide by 2″ long by 1/2″ thick.  It has a weatherproof 3-wire electrical connector and a 1/2″ long tube that the pressure hose from the intake manifold slips over.  The sensor is mounted to a somewhat larger flat bracket with a slight bend in it.  The bracket has an angled slot and is supposed to be secured to the back side (towards the front of the bus) of the engine computer mounting bracket by a single bolt that the slot slips over.

No doubt there is an easy (correct) way to mount the bracket, but it probably requires disassembling other stuff to create access.  That was not going to happen, at least not today.  One problem was that there was not a lot of space to get my hands in there to work.  Another problem was that I was working “blind.”  Even though I had a telescoping mirror I could not position it correctly in the available space and I needed both hands to install the bracket.  But the real problem was that the retaining bolt had long ago disappeared and I had no idea what bolt was supposed to be used or if it threaded into a hole or required a nut.

I had looked this up in my engine manual some time ago so I knew where and how the bracket was supposed to mount, but the manual did not call out the diameter, thread pitch, or length of the mounting bolt.  I tried several bolts that I had but none of them where right.  I asked Barb to keep an eye on my tools and bus while I made a quick run to Herb’s Hardware where I bought an assortment of bolts.  None of them fit.

One of my original bolts was “close” but a little loose.  I decided to wrap it generously with Teflon tape to see if I could fatten it up enough to hold.  I reattached the electrical harness, shortened the pressure hose, and reattached it as I would not be able to make these connections after the bracket was mounted.  I finally managed to get the bracket installed and I think my taped bolt will hold it until we get home and I can figure out the correct bolt.  Even if/when I do, there is no good way to get in there and tighten it.  I ended up using a 7/16″ short socket with a swivel adapter and 6″ long drive extension that I turned by hand.  At least it was mid-late afternoon on a beautiful day with abundant sunshine illuminating the west-facing engine bay.

I still have a half dozen projects to take care off over the next four days but it was good to have the dashboard and turbo boost sensor completed.  During the course of the afternoon I discussed with Barb and Jim what I had found about the use of potassium bromide (KBr) to control seizures in dogs and cats.  I really hope they will discuss this with their vet.

I made popcorn for a late afternoon snack and then checked my e-mail to see if Stacy had proofread my Quartzsite 2015 article and deal with any other correspondence from publisher Gary Hatt.  She had called in sick again, so the proofreading was delayed yet another day.  Linda had called while driving home but caught me in the middle of working on the turbo boost sensor mounting.  I called her back around 6:30 PM my time (8:30 PM EST).  She was really tired so we did not talk very long.

At 7:30 PM (MST) I called David Lambert.  David currently lives in a group home in Olympia, Washington (PST).  He has long been the adult best friend of J.C. Armbruster, my best friend from high school (besides Linda, of course).  I met David on a visit to Washington State many, many years ago and we also became friends.  I learned then that David had struggled with bi-polar affective disorder all of his life and it has not gotten better for him with time.  He does not have much contact with people outside of the group home other than J.C., who has really come to his rescue over the last couple of years.  David does not usually have much to say, but I try to let him know that I know he exists.  Tonight, however, he was a bit more talkative and told me about recent visits with his sister Mary Kay from Everitt, Washington and his half-sister Soliel, who is moving to Sacramento, California.  He also like to watch the TV program “Axe Men.”  He is at least a 3rd generation native northwesterner and logging is part of his family heritage.

For dinner I heated up the “Soyrizo” we bought at Albertson’s supermarket.  I diced garlic, shallot, sweet onion, carrot, green and jalapeño peppers and sautéed them is a little olive oil before adding the soy Chorizo and heating it thoroughly on high heat.  It was a filling but tasty dish.  After dinner I resumed working on the photos of Larry and Carol Hall’s GM bus conversion.  By the time I got to bed and turned the lights out it was midnight.

2015/02/25 (W) Another “Little” Bus Project

I was up at 7:30 AM, which seems to be my norm when I’m in bed by midnight.  The local Farmers Market operates on Wednesdays and this would be my last opportunity to buy a loaf of Barry’s Basic Bread.  I skipped coffee and breakfast, got dressed, and counted out enough dimes and nickels from the cup where we store our change to cover the $3 cost of a loaf.

Once I got back to the coach I made coffee and had breakfast and then settled in to finish yesterday’s blog post, which needed a lot of work, and start on today’s post.  Jasper sat on my lap purring and enjoying my attention for quite a long time before moving to the dinette.  Juniper ate breakfast and then stretched out on the passenger seat as she does most mornings.  The cockpit is the part of the bus that gets coldest at night but since we are parked facing east it is the first place to warm up in the morning.  The sun is not coming up due east yet, of course; that doesn’t happen until March 21st, but it is rising more directly in front than it did in late December and much of January.

I still had a list of bus projects to work on, but first I checked my e-mail.  I did not have a communique from Stacy or Gary so I logged in to our WordPress website/blog and replied to a comment Kate had recently posted.  While I was logged in I updated three plug-ins, deleted 80 spam comments, and initiated a Wordfence scan.  I repeated the update process for the FMCA Freethinker and Great Lakes Converted Coaches websites and the South Lyon Area Amateur Radio Club website.  “In for dime, in for a dollar,” and “no time like the present” are phrases that came to mind.

I don’t seem to get started on bus projects much before noon, but that’s OK; nowhere is it written that I have be working on the bus at sun up.  The bus projects still to be done include:

  • Replacing the solenoid operator on the air-conditioning shutters.
  • Replacing the solenoid on the pilot valve that controls the level low front axle.
  • Securing the wheel well body panel just forward of the PS drive axle.
  • Starting the generator and making sure it works by turning on all three A-C units + Starting the bus and making sure everything works, including repositioning the bus and re-leveling it to make sure the Level Low system is working.

Butch and Fonda were gone all morning so I did not know if my operator solenoid had arrived yet via the USPS.  I don’t have time at the moment to sit in a holding pattern so I decided to work on the body panel.  It was being held on by only two screws and a bolt without a nut, so I was able to remove it without too much difficulty.  (When someone says “without too much” it means “with some.”).  Once the body panel was off I could see clearly that it was supposed to be attached at six points plus the bolt that connected it to the next piece of wheel well trim.  Two more things also became obvious:

  1. that the missing screw I had set out to replace could not be reached without removing the splash guard panel in front of drive tires, and
  2. I was going to have to slide under the bus in order to reach some of the screws.

Given that reality, I slid one of my stands under the chassis just aft of the passenger side rag axle.  The chassis was about 1″ above the stand but I was reasonably confident it would keep the bus from falling on me if the passenger side air springs failed suddenly.  I also pulled out one of my large sheets of plastic that make it a lot easier and more comfortable to slide under the bus, especially on gravel.

I had removed and replaced the two splash guards at Butch and Fonda’s house this past fall when we replaced the ride height linkages.  Fonda helped me with that project so we both knew how obnoxious a job it was even with the bus sitting on four chassis stands so I could get under it easily and work safely and comfortably.  But there was no way around it, so the splash panel came off.  We put the body panel back in place but had trouble lining it up with the holes in the chassis.  Where the front top corner attached we could see that an old fastener had rusted into the hole and sheared off, probably when someone tried to remove it.

Someone showed up to talk the Butch and Fonda about their work-camping job for next winter so I continued working alone.  I eventually got the panel secured at all six points plus the bolt and got a nut on the bolt.  I also got the splash guard back in place with the three retaining screws installed.  The fourth mounting point, however, used a bolt with a spacer tube and a locknut and was in a location that made it impossible to install by myself without getting completely under the bus and sitting up by the transmission or pulling both drive wheels off, neither of which was going to happen.  That meant I needed Fonda’s assistance again.

I started putting my tools away and cleaning up my worksite while I waited for Butch and Fonda’s visitor to leave.  He eventually did and Fonda came over to help me with the last attachment point on the slash guard.  Once that was done, again with some difficulty, I put my tool boxes away and locked up the bays and the car.  It took a whole afternoon for what started out as a job to replace one missing screw.  That’s often how it goes with buses.

I washed up (buses can be dirty work) and then worked on this post for a while.  I called Linda a little after 5:45 PM my time (MST) figuring she would be close to being done working for the day.  I figured correctly and we talked for about 15 minutes.  The issue with the generator required a new pressure regulator and some new hoses.  Natural gas operates at 1/2 to 1/3 the pressure of propane and, even though the generator engine is supposed to work on either just by changing an electrical connection, Bratcher Electric said they have seen this delayed failure quite a few times when switching from propane to natural gas.  It is still programmed to self-test on Thursdays at 11AM EST, so we will see if it auto-starts tomorrow like it should.

For dinner I made a mixed greens salad with onion, carrot, green pepper, dried cranberries, honey roasted peanuts, Daiya pepper jack vegan cheese, and Tofurkey brand deli slices cut into thin strips, dressed with Newman’s Own Creamy Balsamic dressing, and a couple of grinds of fresh black pepper.

I was starting to run low on the lightly flavored/carbonated water that I enjoy and we were almost out of raisins which I use on my salads.  I was also out of hummus and Snyder’s Sourdough Pretzel Nibblers both of which are unacceptable things to be without.  I had checked the Road Runner Market here in town a couple of days ago but they did not have any of these products.  Our supply of small paper bowls and plates was also getting low.  The forty mile round trip to Albertson’s in Blythe, California would take 75 to 90 minutes and two gallons of gasoline, costing $5 to $6, but I decided to make the trip after sunset rather than work at my computer.  The left side of my neck and left upper back were bothering me more than usual as a result both of long hours at the computer and working under the bus on the body panel today.

As long as I was at the store I picked up a few things that were not on my list including:  Ken’s Steak House salad dressings, several different fruit preserves, another bottle of honey mustard (with real honey), another pack of Tofurkey peppered mock deli slices, some black grapes, extra chips, and two bottles of Goslings Ginger Beer.  It was an easy run over and back, a nice drive over the small mountain range that separates this part of Arizona from California.  We have not driven around much at night since we have been in the southwest and I discovered that both Blythe and Quartzsite sparkle like gems at night.  On the drive from Blythe back to Q I could easily see all the way to the other side of the valley once I was clear of the pass.  Not only were the lights of the city spread out before me, I-10 was a ribbon of white and red light snaking up the KOFA Mountains until it disappeared over the next pass.  It was quite a sight.

Back at the coach I got all of the groceries moved from the car to the kitchen and put away.  The plastic bags often end up with holes in the bottom because they are so thin so I sorted them according to whether they had holes or not and ended up with five of each.  How convenient.  I put one holy bag inside each unholy bag creating five ready-to-use double bags.  Sometimes I amaze myself.  But I can only bask in the glory of my accomplishments for so long and then I have to get back to the processes of daily life. Tonight that meant cleaning up the dishes from dinner and checking e-mail.  I lose track of time when I am working and it was well after midnight by the time I turned off the lights.

2015/02/26 (R) LiveStream

For some reason I was awake at 7 AM.  I can function on only six hours sleep but I do better on seven.  By eight hours I am uncomfortable and need to get up whether I am rested or not.  Even before I got up I heard engine noses and voices outside and looked to see what was going on.  It took me a moment to recognize Larry and Sandy’s motorhome and then remember that they were taking it to Yuma for a long weekend.  Larry had told me yesterday they were going to do that so they would be in a good position to watch an air show at Marine Corps Air Station Yuma.

It has been getting cool overnight, dropping into the upper 40’s, so I put on my sweat pants and shirt.  We bought these not long after we got to Quartzsite so we would have something easy and comfortable to wear on mornings when it was cool in the coach.

I fed the cats, refreshed their water, cleaned their litter tray, bundled up the trash, ground up some Sweet Seattle Dreams coffee beans, and brewed a pot of coffee.  I got out the two blue blankets and put one on the dinette seat and one on the passenger seat.  Jasper immediately curled up on the dinette blanket and Juniper curled up on my lap while I sat on the coach working on my blog posts for yesterday and today and enjoyed my first cup of coffee.

I like the start of the day; it is one of my favorite times.  I am usually rested and generally relaxed and have the comfort of my small morning routine.  The whole day is in front of me and it is still possible to accomplish something, anything really, but not everything, and sometimes not much.  The end of the day is always more variable.

I only have a few repair tasks left to do on the bus plus one or two on the car.  Bus-wise, I need to:

  • Replace the solenoid operator on the air-conditioning shutters.
  • Replace the solenoid operator on the pilot valve that controls the level low front axle.
  • Replace one of the driver side headlights (it has a small hole in it).

Car-wise, I need to:

  • Replace the two auxiliary tail lights in the car.
  • Wash and wax the car.

Although I have most of the parts I need I was expecting another solenoid operator for the shutters to arrive in yesterday’s mail.  It did not, so I hope it arrives today as I really do not want to replace the whole valve nor do I want to disassemble the new one, even though I’ve been told that it is OK to do so.  I think the headlight can wait until I get home, but I need to see if I have one with me.

The other things I have to do are not maintenance/repairs, just routine checks to make sure that we, the car, and the bus are ready to roll on Tuesday.  These include:

  • Starting the generator and making sure it works by turning on all three A-C units + some additional load(s).  That will also verify that the air-conditioners work.
  • Starting the bus and making sure everything works, including repositioning the bus and re-leveling it to make sure the Level Low system is working.

The things that will wait until Monday include checking/setting all of the tire pressures, which I will do on Monday morning, and making sure the hitch and tie bar are ready to go.

While I was working on this post I got a call from Joe Cannarozzi, the mobile mechanic who has maintained our bus chassis, generator, and some aspects of our main engine for the last four years.  He is still in Mississippi but starting to arrange his spring service calls enroute to his summer job in upstate New York.  Unfortunately it looks like he will be in Michigan in early April and we will miss him this time around.

By the time I finished breakfast it had warmed up enough in the coach to take a shower.  I then started a load of laundry and settled in to upload some blog posts from early January.  I decided to keep doing consolidated posts and started pulling together the ones for January 1st through 7th.  I selected nine photos from these dates and processed them.  My work was frequently interrupted by the three loads of laundry I was doing and some necessary housekeeping.

The water level in our fresh water tank was indicating below 1/3rd so I checked it visually.  It was at 1/4 so I filled it, which took about 90 gallons.  I tested the water coming out of the softener for total hardness (TH) using a test strip from each bottle as I wanted to make sure the strips gave me the same reading.  They did, and it was somewhere above 0.0 and below 1.5.

As the tank was nearly full I noticed water on the floor of the bay and determined that it was coming from the fresh water tank drain valve.  I soaked up the water that was there and tried moving the valve quickly open and then closed to see if that might clear a small piece of debris or somehow “seat” the valve.  The leak was not coming out the drain pipe onto the ground.  It was seeping around the top of the valve housing but I could not determine if it was coming from a seam or around the metal rod that comes out the top and attaches to the knife blade inside.  This is a 1-1/2″ diameter valve of the type used on smaller RV waste tanks, especially grey water tanks.  I will check in the morning to see if it leaked overnight and probably make a trip to several of the RV stores here in town to see if I can locate a spare valve.  I won’t be able to attempt a repair, however, until the tank is almost empty so I only have to dump (waste) a small amount of softened fresh water.

Interspersed with my blog work I had some pretzel nibblers and sun-dried tomato hummus and eventually ate a grapefruit.  I did not feel like fixing anything fancier so that constituted lunch.  Butch and Fonda left at 1:45 PM to check the P. O. Box and then go to a meeting of the Quartzsite Gem and Mineral Club.  They stopped at the post office on the way hone but there was no package for me.

Linda called at 2:45 PM my time.  She had wrapped up her year-end work at the bakery and was back at the house making a cup of tea before settling in for one more evening of tax return work.  She was fairly confident that she would have everything wrapped up tonight or tomorrow morning.  There was a tentative plan in place for her to babysit Madeline Friday evening so Brendan and Shawna could go out.  Plans were also in the works to attend a women’s gymnastics competition at the University of Michigan on Saturday and then go to dinner.  She did not mention whether Meghan would be joining them.

Sometime during the afternoon I got the last load of laundry out of the dryer and put away.  I took a break from working at my computer around 6 PM to sit and chat with Butch and watch yet another gorgeous Quartzsite sunset.  In spite of a cooler air mass the sun was very hot today, but once it started to set the air temperatures asserted their presence and we eventually retreated to our coaches for the evening.

I continued working on my blog post, checking e-mails as they popped up.  I had one from Gary with my Quartzsite 2015 article attached.  Although Stacy had not made it into work she was feeling well enough to edit it at home.  I had planned to view a live Technomadia chat on “Making Connections on the Road” at 7 PM but forgot to tune in.  I realized my oversight around 7:30 PM and joined the event in progress, but first I had to create an account with the LiveStream service which involved the usual e-mail verification process.  But it was quick and I got to see/hear the last 20 minutes of the event which was mostly Q&A.  The whole thing was archived, however, so after it ended I nuked a vegan hot dog for dinner and then replayed the part I had missed.

I had not yet made the bed so I took care of that and then resumed working on my blog post.  I finally uploaded the post sometime around 10:30 PM and by the time I uploaded and captioned the photos, created all of the tags, and clicked the “publish” button it was after midnight.  Rather than wait until tomorrow, I went through Stacy’s edits of my article, accepted most of them, and rewrote a couple of awkward sentences.  I uploaded it to the BCM folder in my Dropbox and then e-mailed Mike (editor) and Gary (publisher) that it was there along with all of the photos.  I also e-mailed it back to Stacy and Gary so she could compare it to the one she sent me.  I got to bed at 1:30 AM, later than I like but with some things accomplished.

2015/02/27 (F) Granola Express

In spite of going to bed so late last night (early this morning, actually) I was up at 7:45 AM.  That was mostly because the cats do not care what time I went to bed.  They have their routines and by 8 PM they figure breakfast and fresh water are way overdue.

Linda called around 9:15 AM my time to ask me about a bucket full of water in the furnace room. The double wall stainless steel flue pipe for the furnace runs horizontally under the floor joists through the furnace room and then through my office above a suspended ceiling and finally out the east side of the house.  Moisture tends to condense inside the pipe and drip out of it at the joints between sections if they are not sealed.  The bucket is there to catch the drips and it was full.  It used to drip on the furnace but Tom from TOMTEK HVAC sealed that gap so now it drips somewhere else.

Linda checked the status of the UPS delivery of the “care” package Linda shipped to me.  It was in Blythe, California at 5:15 AM this morning and scheduled for delivery by the end of the day.  It will be nice to finally have my pillow and once again be able to enjoy Linda’s homemade granola.

After breakfast I checked my e-mail, updated my water usage spreadsheet, and finalized my FMCA Freethinkers 2014 financial statements.  The statements are now ready for Linda to audit, which will take her all of 10 minutes (at most).  I then took stock of my BCM articles that are “in-process” and decided to finish the one on the Turbo Boost Repair and move it to the proofreading stage.  With that done, I started pulling together the next consolidated blog post for January 8 – 14, 2015.

For lunch I made a sandwich with sourdough bread, salad greens, vegan deli slices, vegan cheese, pickles, veganaise, and honey mustard.

The solenoid operator from Hei/Tek in Phoenix was not in today’s mail so something obviously went wrong.  I called Hei/Tek and talked to Brie.  She checked with her shipping department and called me back to let me know it got sent UPS ground to our P. O. Box.  UPS does not deliver to P. O. Boxes so it was sitting in Blythe, California in an undeliverable status.  I gave them our P. O. Box number because she told me on Tuesday they were going to mail it (USPS).  Brie gave me the number for UPS, but it was a national 800 number.  I looked up the local Blythe UPS center but it had the same national number listed.  It also indicated their Will Call hours were M – F, 9 – 10 AM.  I called the 800 number and Jose fielded my call.  He changed the status to “hold for pickup” and we will have to drive to Blythe on Monday to get it.

Somewhat ironically I had a UPS delivery scheduled for today and it arrived around 4 PM.  My part could have been on the truck had I done something about this on Wednesday or Thursday.  The box contained an envelope for Butch and Fonda and a small envelope for me.  My envelope contained license plate tabs and registration cards for both vehicles, and dues check for our FMCA Freethinkers Chapter.  The box also contained my pillow, which I have missed, and four bags of Linda’s homemade granola, which I have really missed.

Since I could not get my part until Monday I decided to take the operator solenoid off of the new valve and put it on the old valve.  This was certainly a faster, easier job than replacing the entire old value/operator with the new valve/operator.  I put air to the shutters and used the low voltage control circuits to test the new operator solenoid and it worked as designed and built.

I settled in at my computer to work on the next consolidated blog post, stringing seven separate posts together and selecting/processing photographs.  I worked on a detailed e-mail reply to Gary at BCM and then worked for a while on another article that has been “in-process” since January.

I was finally hungry around 9:30 PM and heated up an Amy’s frozen Sweet and Sour gluten free noodle dish.  Much to my surprise it was not very good, which is unusual for Amy’s products.  I needed to get up and adjust tire pressures first thing in the morning so I made sure I was in bed with the lights off by midnight.

2015/02/28 (S) Out With A Roar

I got up at 7 AM and debated whether to go ahead and adjust the tire pressures or make coffee and eat breakfast first.  I was a short debate and I won.  It was 8 AM by the time I finished my granola and my first cup of coffee.  The sun was well above the horizon but partially obscured by clouds and the temperature was 57 degrees F.  I put on my zip front work hoodie (sweatshirt jacket) and went out to take care of business.

I turned on the TireTraker Monitor and stuck it in my pocket.  As I removed each sensor it triggered a brief alarm on the monitor.  Most of the bus and car tires were close to correct according to my air pressure gauge, with some slightly over-inflated and some slightly under inflated, except the driver side steer tire on the bus which was four pounds low.  When I put a sensor back on the valve stem it reestablished communication with the monitor.  This is supposed to trigger a new/current reading on the monitor but it appeared to me that all of the displayed pressure values were off, reading high in most cases by 3 – 4 pounds.  I am not convinced yet that this system works the way I was told it does.

With the tires taken care of I disconnected the air hose from the air-compressor and stored it in the tray over the driver side drive wheels along with the air pressure gauge and air chuck.  I disconnected the power cord and rolled it back up on its reel and then put the air-compressor back in its travel compartment in the car.  I then went back inside to have my second cup of coffee.

A wind advisory was in effect for today and through the overnight hours.  Winds were forecast at 25-30 MPH with gusts over 40 MPH and that is what we got.  The temperature barely reached 70 degrees F while the sun played peek-boo with partly cloudy skies all day.  The combination made for a brisk day.  The forecast for Sunday morning through Tuesday noon is for rain, with possibly an inch along and north of I-10, and a flash flood watch from 5 PM Sunday until 5 PM Monday.  February was definitely going out with a roar.

I spent the central part of the day cleaning out the front bay of the bus and re-packing it.  We acquired a few things while we here, most notably supplies for cleaning and waxing the bus, and they had to be stored someplace for travel.  We had kept several cardboard boxes from UPS shipments and I used those to organize the new cleaning supplies and stow them in the back seat of the car.

Butch and Fonda put their mats away yesterday and I should have done the same but was busy with other things.  Jim L. stopped by to use Joe and Connie’s WiFi DSL gateway.  I gave him about 30 pounds of solar salt for his water softener and he helped me fold up our large patio mat.  As I have written here, the solar salt is simply not effective in recharging our portable water softener.  We could use it at home in our residential water softener but it is a heavy, bulky, and inexpensive commodity so it made more sense to leave it here with someone who could use it than to transport it over 2,200 miles.

Jim L. suggested that I pull out by pulling forward, cutting my front tires hard to the right, and angle out between a concrete pad and the Palo Verde tree (bush) by the light pole.  The Palo Verde was hanging out far enough that I decided to trim a few branches so as to avoid any possibility of scratching the passenger side of the coach.

My one little repair project today was to try building a “retaining pond” on the floor of the water bay underneath the leaking fresh water tank drain.  I used self-stick weather seal formed to circles, one inside the other.  I had noticed that there is a small gap where the discharge pipe turns and goes through the floor.  My solution was to contain the water that is seeping from the drain valve in the little retaining pond and give it a chance to flow down through the gap.  We are going to pick up some inexpensive bath towels on Monday to soak up the water.  We can ring them out, line dry them in the dry Arizona air and brilliant sun, and re-use them.

The only outside chores I have left to do to get us ready to leave are to:

  • dump the waste tanks.
  • clean and stow the dump hoses and fittings.
  • top up the fresh water tank.
  • recharge the water softener (maybe).
  • check the engine oil and top it up if needed.
  • check the hitch, tow bar, and cables.

Mid-afternoon I called J. C. and left a message.  He called me back a short time later and we talked for almost two hours.  J. C. was my best friend in high school (Linda had her own special status) and is one of the only people from that period in my life with whom I am still in contact.  J. C. works at Boeing Aircraft as an inspector in the 737 production facility.  He is only a few months younger than me but is looking at age 66 as his earliest possible retirement point.

I also had a call from Pat Lintner.  Pat is the National Director for our FMCA GLCC chapter and is also the Senior VP of the FMCA GLAMA.  He wanted to give me a heads up that Jane Roush, the GLAMA President, would be sending an e-mail later today to all of the GLAMA chapter presidents and national directors regarding a recommendation that the Midwest and Great Lakes areas be merged.  The Great Lakes Area consists of Indiana, Michigan, Ohio, and Ontario and has 21 chapters, the smallest number of any FMCAA area.  The Midwest Area is made up of Illinois, Wisconsin, Iowa, Minnesota, South Dakota, North Dakota, Manitoba, and Saskatchewan and has 24 chapters.  All of the other nine areas have more chapters.  I did, in fact, receive Jane’s e-mail a few hours later and forwarded it to all of the GLCC members for whom I have valid e-mail addresses along with a few additional comments.

The rest of the day was spent doing this and that.  Linda called and brought me up to date on her day.  She went with Brendan, Shawna, and Madeline to Crisler Arena at the University of Michigan Ann Arbor to watch part of a women’s gymnastics competition.  Meghan and Chris met them back at the Fay-Lee house for dinner.  I cleaned up the dishes, mostly silverware that had accumulated over the last few days.  I checked and replied to e-mails, mostly from Gary at BCM.  I worked on my consolidated blog post for the second week of January and had it ready to upload by 11 PM but was too tired to start the process at that hour.

 

2015/02/06 (F) KOFA NWR Palm Canyon

 

Palm Canyon Road entrance to KOFA NWR.

Palm Canyon Road entrance to KOFA NWR.

I slept in until 8 AM, got up, put on my sweats, and made a pot of coffee.  While that was brewing I turned the TT-400C TPMS monitor on and then adjusted the pressures in the four car tires and checked the passenger side steer tire on the bus.  Based on the temperatures it was reporting the monitor appeared to not be picking up the six rear tires on the bus so I plugged the PressurePro repeater in.  It is mounted in the passenger side rear corner bedroom cabinet and Darryl Lawrence said it should work fine with the TT-400C monitor.  Consumer TPM Systems all operate on the same frequency of 433.92 MHz and the repeater just receives, amplifies, and retransmits signals on that frequency.  The sensors have a unique digital identity and send out an encoded digital signal; that’s how the receiver/monitors know which signals to display and ignore the rest.

Linda in the parking lot at the mouth of Palm Canyon, KOFA NWR, AZ.

Linda in the parking lot at the mouth of Palm Canyon, KOFA NWR, AZ.

The north wall of Palm Canyon, KOFA NWR, AZ.

The north wall of Palm Canyon, KOFA NWR, AZ.

 

 

After a breakfast of juice and cinnamon raisin oatmeal Linda went for a walk while the air temperature was still cool.  I stayed at the coach and dumped the holding tanks, made up our mixture of a bottle of PineSol with an equal amount of water and a cup of Calgon bath beads.  Shake until dissolved and add ~60% to the black tank (via the toilet) and the other 40% to the gray tank via the bathroom and kitchen sinks, including the In-Sink-Erator.

 

 

 

 

The beginnng of the Palm Canyon trail, KOFA NWR, AZ.

The beginnng of the Palm Canyon trail, KOFA NWR, AZ.

 

 

With my chores done I recorded the dump in our notebook and then added the information to our Water Usage spreadsheet.  According to the spreadsheet and our notebook it had been 19 days since we last emptied the waste tanks.  I knew that wasn’t possible as we normally dump every 9 to 10 days when we are in normal water usage mode, and Marilyn was here for the first half of that interval.  Clearly we had forgotten to record a dump 9 or 10 days ago.

 

 

The north wall farther into Palm Canyon, KOFA NWR, AZ.

The north wall farther into Palm Canyon, KOFA NWR, AZ.

 

 

 

I finished working on some additional draft items for the survey the FMCA National Education Committee wants to send out.  I sent them to the committee chair (Gaye) and the member whose items I was revising.  We have another phone meeting on Monday and I wanted to get these items out to the committee by tomorrow so the members have time to look at them.

 

 

 

 

 

 

 

I got an e-mail from Gary at BCM last night advising the editor that I was doing an article on Quartzsite for the February 2015 issue and would have it done by the end of next week.  I e-mailed him back last night and then wrote it this morning and e-mailed it to him and Mike, the editor, for review.  Although I am no longer employed, I sometimes still work better against a deadline.

Deeper into Palm Canyon approaching the 1/2 mile mark.  KOFA NWR, AZ.

Deeper into Palm Canyon approaching the 1/2 mile mark. KOFA NWR, AZ.

After cleaning and waxing the bus and spending a lot of time sitting in front of our computers we wanted to get away from camp and do some sight-seeing.  The repair we had done yesterday to the passenger side rear tire on our car seemed to be holding so at 2PM we headed for the King OF Arizona (KOFA) National Wildlife Refuge (NWR) Palm Canyon area about 20 miles south of town.

A lone palm backlit high up on the south wall of Palm Canyon, KOFA NWR, AZ.

A lone palm backlit high up on the south wall of Palm Canyon, KOFA NWR, AZ.

This seemed like a good spot to stop and let Linda take my picture for a change.  Palm Canyon, KOFA NWR, AZ.

This seemed like a good spot to stop and let Linda take my picture for a change. Palm Canyon, KOFA NWR, AZ.

Palm Canyon is an enormous slot in the Kofa Mountains.  The canyon is aligned ENE to WSW opening to the WSW so we figured the best light would be in the mid-to-late afternoon.  To get there we drove south out of Quartzsite on US-95 about 19 miles to Palm Canyon Road and then east for seven miles on a good gravel roadway.  Good is relative, of course; it took as long to drive the 7 miles as it did the 19.  The trailhead is at the end of the road, which is the beginning of the canyon.  There are also several areas just off the parking/turnaround designated for tent camping, and it would be a spectacular place to pitch a tent.  The last mile or so of the road climbs more than you realize until you get to the parking area and are treated to a sweeping view of part of the La Paz Valley that stretches for over 100 miles from Parker on the north end to somewhere north of Yuma on the south end.

 

Looking WSW back out of Palm Canyon at the La Paz Valley.  The trail climbs it goes deeper into the canyon.  KOFA NWR, AZ.

Looking WSW back out of Palm Canyon at the La Paz Valley. The trail climbs it goes deeper into the canyon. KOFA NWR, AZ.

 

There they are!  The fan palms of Palm Canyon high up in a shaded crevice on the south wall of the canyon.  KOFA NWR, AZ.

There they are! The fan palms of Palm Canyon high up in a shaded crevice on the south wall of the canyon. KOFA NWR, AZ.

The trail is a 1/2 mile hike into the canyon near the floor but to the south of, and above, the central drainage wash.  The canyon is named for the California Fan Palm trees that grow there; the only naturally occurring Palm trees in Arizona.  There is lots of other vegetation in the canyon, however, and the palms are a bit elusive.  About a half mile in there is a small wooden sign with an arrow pointing up to the left at a 45 degree angle.  All the sign had on it was the word “PALMS.”  And there they were, way up in a narrow crevice.  Mind you, some of the trees in this main grove have trunks that are 20 inches in diameter, but the canyon is a big place and the trees are far away from where we were standing.  The only wildlife we saw up close were small lizards about 3″ long, 6″ with their tails.  We heard and then saw a bird soaring high above the southern edge of the canyon but could not tell what it was.

 

Delicate colors on the north wall of Palm Canyon in the late afternoon sun.  KOFA NWR, AZ.

Delicate colors on the north wall of Palm Canyon in the late afternoon sun. KOFA NWR, AZ.

 

The light was nice hiking in and got better and better as we hiked out.  The trail climbs quite a bit from the parking area, but not steeply in any one place.  We took our time and I took a lot of photographs.  By the time we got back in our car the sun had slipped behind the Dome Rock Mountain Range that defines the western edge of the La Paz Valley.  We had nice colors in every direction but without any clouds we did have a particularly photogenic sunset.  By the time we got back to US-95 it was approaching 6:20 PM and we needed our headlights even through the glow along the crest of the mountains continued almost all the way back to town.

Looking back into Palm Canyon as we hike out.  KOFA NWR, AZ.

Looking back into Palm Canyon as we hike out. KOFA NWR, AZ.

 

 

 

Linda made a green salad with fresh tomatoes and blueberries, dried fruit, and nuts and dressed it with Raspberry Walnut Vinaigrette.  She heated up a couple of tortillas and used them to make a quesadilla-like thing with Daiya (vegan) cheese, tomato slices, and jalapeño pepper slices.  We had a small glass of Franzia Refreshing White wine with dinner and had red grapes for desert.

 

 

Before we left for our hike I had unplugged the power supply from my ASUS notebook computer to let it cool off.  It seems to me that it runs hot.  I plugged it in when we got back and had a notification on the screen that the computer needed to be restarted to complete the installation of updates.

 

The only wildlife we saw up close in Palm Canyon.  KOFA NWR, AZ.

The only wildlife we saw up close in Palm Canyon. KOFA NWR, AZ.

 

The north wall at the entrance to Palm Canyon in the glow of sunset.  KOFA NWR, AZ.

The north wall at the entrance to Palm Canyon in the glow of sunset. KOFA NWR, AZ.

I decided to check my e-mail first and had a couple from Gary, so I called him after we finished dinner and we chatted for about an hour.  It sounds like the article I sent him this morning on Quartzsite 2015 won’t run until the March issue, so that will give me a little more time to select and process photos, experience more things here, and possibly extend the article a bit.  In the meantime Gary is going to have Stacy proofread all of the articles that are ready plus the one I just sent.

 

 

My ASUS laptop keyboard appears to be functioning correctly again so I was reluctant to restart my computer, but the message said it would restart in one day on its own anyway.  I guess there’s no time like the present to find out if the machine has a problem.  It finished whatever it was it needed to do, powered down, and restarted without a hitch.  I then copied all of the photos from our canyon hike to the computer and NAS and started looking at them.  I processed a few and then went to bed.

 

2015/01/22-26 (R-M) Q 2015 W4

2015/01/22 (R) Sister Marilyn

Marilyn & Linda in front of Beer Belly's "adult day care" outdoor bar.

Marilyn & Linda in front of Beer Belly’s “adult day care” outdoor bar.

The temperature dropped into the low 40’s last night in the wake of the cold front that brought strong winds to Quartzsite yesterday.  We were up at 6:30 AM to give us time to eat breakfast and enjoy our coffee before Linda left at 8 AM for the Phoenix airport to pick up her sister.  Marilyn was scheduled to arrive at 11 AM MST and the airport is a 2 to 2-1/2 hour drive from Quartzsite but Linda wanted to take her time getting there and be in the cell phone lot before the flight got in.  The plan was to go to lunch and then drive back to Q so she was going to be gone most of the day.

I had turned off the diesel burner on the Aqua-Hot last night so this morning I turned on the three electric toe-kick heaters and the Broan cube heater to take the chill off of the interior.  With the coffee pot also turned on we were drawing 26 A at 115 VAC on leg 1 and 15 A at 118 VAC on leg 2.  That was more current than we were able to draw before Jim L. changed the shorepower connection from 30 A (120VAC) to 50 A (240VAC) and the first time we have had reasonable voltage levels since we arrived here.

I rode over to the RV show with Butch at 9 AM to look at tire pressure monitoring systems and we both ended up buying TireTraker TPM Systems from Darryl Lawrence.  We have both done business with Darryl in the past and trust him as a vendor.  I also bought three products from the Carnu-B booth.

Back at the coach I checked the coolant level in the Aqua-Hot expansion reservoir.  It was right at the maximum cold level so there was nothing else to do for the moment.  I needed to redo the overflow hose, but not today.  I then used two of the Carnu-B products on the driver-side side window and surrounding painted body surfaces.  It removed the hard water stains and polished everything up very nicely.  I then did a test patch on the front of Butch and Fonda’s bus and it appeared to clean the stainless steel nicely.  They later cleaned an adjacent patch with straight food-grade vinegar and it seemed to work just as well although it did not provide a wax finish.

While I was fiddling with the Aqua-Hot and the cleaning/waxing process Butch started reading the manual for the TT-TPMS and found information that indicated the system did not work the way we thought it did and needed it to.  The manual more than implied that the sensors were activated by motion and stated that readings would appear “… within 20 minutes of starting to drive.”  Say what?!  We both want to use the system to check our tire pressures BEFORE we start to drive, as would most RVers.

Although there are things we do not like about our current Pressure Pro TPM systems they certainly give us the current pressure in the tires without having to drive the vehicle.  They also allow us to monitor just the bus, just the car, or both.  Most systems do this, including the TireTraker, but the Truck Systems Technology (TST) does not.  That was Butch’s first choice system until he found that out.

At 12:45 PM I rode over to the Quartzsite Senior Center with Butch and Fonda for a 1 PM meet and greet with Chuck Woodbury of RV Travel and the Geeks On Tour.  It ran until 4 PM but we were anxious to get back to the RV Show tent and talk to Darryl.  We took our TT-TPMS units with us with the intent of returning them but Darryl assured us that they do work the way we need them to so we decided to keep them for another day or so to test them.

Fonda had not been to the RV Show yet so we walked the entire tent.  I spent a little time talking to the guy at John Carrillo Hydronic Heating.  He had a brand new, never been fired, Webasto DBW2010 burner (with the controller) for $1,800 (cash).  I have seen them online for $3,300, so I knew that was a good price.  I wish I needed one, but we already have a spare.  He also had a new combustion chamber for $200 and I may go back and get one of those.  They wanted $450 for an ignition coil, which I also need, but I can get one from Sure Marine Service for $303.  We spent a long time looking at flag poles at the Flag Pole Buddy booth and Butch bought a 22′ model with an extra set of mounts.

Linda was texting me her status on a regular basis and by the time we got back to camp she and Marilyn were already there and relaxing on the porch of Joe and Connie’s park model trailer.  We sat outside until the sun kissed the tops of the southwestern mountains and then moved inside to escape the chill.  While we were sitting in the coach visiting and cooking Butch installed one of the TT-TPMS sensors on the driver-side front tire of their Suburban, programmed it into the monitor, noted the readings, and went for a test drive.  He noted the readings when they got back and plans to check it again in the morning before moving the car.  That will be the real test.

For dinner Linda made a nice green salad and a lovely mushroom kale risotto with Arborio rice.  We then went to the apartment so I could light the pilot flame on the wall-mounted propane heater.  I visited for a bit and then went back to the coach and Linda followed a bit later.  We were both tired and turned in early.

240 degree panorama from atop 'Q' Mountain, Quartzsite, AZ.

200 degree panorama from atop ‘Q’ Mountain, Quartzsite, AZ. Left edge is N, right edge is SSW.

2015/01/23 (F) Q Mountain

We were up by 7:30 AM and Marilyn eventually arose and joined us for coffee and toast.  The only bread we had was a package of whole wheat pitas, but they toasted just fine and were very good with orange marmalade.  I am not, however, thrilled with the Soy Delicious Almond milk coffee creamer.  It is not as ‘creamy’ as Silk soy creamer and it tends to separate into tiny bubbles in the coffee.  I do, however, like the Almond milk that we sometimes buy, especially on granola type cereals.

Butch called just after breakfast to let me know that the TireTraker TPMS works the way Darryl said it does.  That was welcome news as we both like the system, including the small sensors and the rechargeable monitor, and we both like Darryl.  He and Fonda had things to do today so I borrowed his hose crimper pliers before they left.

Linda and Marilyn left shortly after Butch and Fonda and drove to Blythe, California to do some grocery shopping and sight-seeing.  That left me with some alone time to concentrate on getting some things done that I have needed to work on for a week, such as categorizing FMCA seminars, and have just not found (made) the time.  I value and enjoy my work with the FMCA National Education Committee but we have a significant personal investment in our presence here in Quartzsite, and although we will likely return here again in the years to come that is not guaranteed, and this could turn out to be a once-in-a-lifetime experience.  The FMCA work took about an hour to complete and e-mail too Jim A., with who has been the lead person on this.

I also needed to make a minor change to the Aqua-Hot expansion tank plumbing and turn the burner back on.  I removed the overflow hose, shortened it, re-routed it, and re-connected it to the drain tube on the tank.  I also tried to tighten the clamp on the middle zone pump hose.  I noted that the coolant level was at the ‘minimum cold’ mark on the expansion tank.  I will check everything again tomorrow.

With the Aqua-Hot project done I decided to replace the old Sentry turbo boost gauge with the new VDO gauge.  I removed the dashboard cover, disconnected the lightbulb connectors, removed the retaining bracket, and pulled the gauge out the front of the dashboard.  I removed the lightbulb socket to give me better access to the main air fitting and undid that, completely freeing the unit from the dashboard.  I pulled the light socket out of the new gauge to give me more room to put the air fitting on and to check the bulb type.  It was a miniature glass wedge base 12VDC 3W and will need to be replaced with a 24V, 3W bulb.  I then slipped the gauge into the dashboard from the front and secured it with the supplied bracket on the back side.  Linda and Marilyn returned at this point so I quit working on the gauge, put the cover back on the dashboard, and helped bring in the groceries.  I will have to get the 24V bulb and also rewire the leads to match the harness connectors.

We had a light lunch and then drove down to the market area and wandered through the big tent RV show.  We got new Ballisti-Tech screen protectors for our Samsung Galaxy S III smartphones.  We also strolled through a small part of the Tyson Wells and Prospectors Panorama areas.  When we left the RV show we headed south on US-95 to the BLM Roadrunner STVA so Marilyn could see the Quartzfest RVs in the desert.  We found Lou and Val Petkus at their 5th wheel and visited briefly before heading back to town.  The light was good and the sun was still high enough that I made an impromptu decision to climb Q Mountain and try to get pictures of the RVs spread across the desert around Quartzsite.

I got my pictures, and got off the mountain before it got dark, but missed the best color, which we saw while driving back to camp to close up the rig before going to dinner.  The Geeks were out viewing and photographing the sunset before walking to the Grubstake restaurant for dinner so and we chatted with them briefly and then drove to Crazy Jerry’s for our evening meal.  The very thin crust mushroom, onion, and tomato no-cheese pizza was excellent and the French fries were also good.  When we got back to our coach Linda prepared some fresh strawberries for desert.

After visiting with Jim and Chris on Wednesday we decided that we would join the Quartzsite Yacht Club, which claims to have the largest membership of any yacht club in the country (world?, universe?) at over 7,500., although we later heard that it was more than 9,000.  Membership is $30 which gets you a hat, T-shirt, membership card and certificate.  Apparently the membership is good at other (real) yacht clubs that honor reciprocal arrangements.  We had planned to join today but did not fit it in.  It may be Sunday or even a day next week at this point.

I spent some time transferring photos from my camera to my laptop computer and our NAS unit.  I processed three panoramas and three individual images taken on Q Mountain, checked my e-mail, and went to bed.

Sunset glow looking NE from 'Q' Mountain.

Sunset glow looking NE from ‘Q’ Mountain.

2015/01/24 (S) Lake Havasu City

We were up at 7:15 AM and I brewed a pot of coffee while Linda showered.  I took my turn and also trimmed up my beard a bit.  Marilyn came over around 8:25 AM and we all had coffee followed by breakfast.  Linda and I had granola while Marilyn had toast and jam.  She is not that found of breakfast and does not care for milk or milk substitutes.

I removed some of the parts boxes from the back of the Element to eliminate the rattling just in case we decided to drive in to the Desert Bar on the way back from Lake Havasu City (LHC).  We left around 9:15 AM and headed up AZ-95 towards Parker.  It was a cool morning with clear skies and the sun lit up the mountains to the west and north.  When we got to Parker we decided to cross the Colorado River into California and take the Parker Dam Road 17 miles up to Parker Dam, drive across back into Arizona, re-connect with AZ-95, and continue north to LHC.

We knew that the stretch of the River from the dam downstream to Parker had quite a few RV Parks, campgrounds, and mobile home communities because we caught glimpses of some of them from AZ-95, or saw signs for them, the last time we were in LHC.  The drive from Parker to LHC is very scenic but you do not have a view of the river most of the time.  Much of the drive from Parker to the dam on the California side, however, was close to water level so we were able to see the resorts on both sides of the river.  We had also heard that there were wild burros along the California route and indeed there were.  We saw five total, two of them just before the dam.  They appear to be docile animals, but they are wild, and you are not allowed to feed or harass them.

Once we got to LHC we followed the signs for the London Bridge and found the parking lot and visitor center.  We watched a video on the history of the London Bridge, which was actually the second most recent in a long succession of bridges across the River Thames dating back before Roman Times.  The Bridge was purchased, disassembled, moved, and reconstructed in LHC.  It was placed at the entrance to a peninsula and then a channel was dug out under it and connected to the Colorado River on either end, turning the peninsula into an island.  There is an “English Village” at the base of the bridge on the mainland side, which was not very special, but a wonderful pedestrian path winds along the channel all the way down to Rotary Park.  The air was cool and the wind was very strong, but the sun was very warm and we had a lovely stroll.

After walking the path we drove over the bridge and around the island, stopping at one of the reproduction 1/8 scale lighthouses.  The LHC Lighthouse Association has erected some two dozen scale replicas of U. S. Lighthouses.  The ones on the island are all replicas of lighthouses from the Great Lakes while the ones on the Arizona shore are east coast replicas and the ones on the California shore are west coast replicas.  While we were driving Linda researched places we might be able to eat lunch and settled on The Black Bear Diner.  She and Marilyn had garden burgers with French fries and I had the Sweet Garden Harvest Salad.  All of the food was very good, and I was particularly pleased with the salad, which had raisins, dried cranberries, nuts, fresh strawberries, and shredded coconut with a honey Dijon dressing.

The restaurant was in a corner of the parking lot for the Albertson’s grocery store so we went in looking for regular Silk soy creamer.  They did not have any so we started back to Quartzsite and stopped at the Basha’s market on the south end of town.  They had the Silk Vanilla Soy Creamer, not the regular, but I got some anyway.  They also had a nice selection of Daiya cheeses and vegan sausages.  We picked up some sourdough bread and preserves on our way to the checkout.  Of all the food stores we have been in Basha’s was the nicest so far.

By the time we got to Parker I was getting tired so I pulled into the casino parking lot.  I switched places with Linda and she drove the rest of the way to Q.  Back at camp she and Marilyn went to the apartment and started assembling a 500 piece puzzle on the dining table.  As I do on any day that I have taken a lot of pictures I transferred them from my camera to my computer and backed them up to the NAS unit.  I used the Microsoft Image Composite Editor to create two panoramic images of the California mountains just south of LHC.

None of us were hungry enough to warrant fixing dinner so we snacked on hummus and chips (vegan junk food).  Marilyn went back to the apartment at 9 PM and we went to bed shortly thereafter.  A long day of fresh air and sunshine had once again worn us out.

2025/01/25 (N) Visitors

Linda& Marilyn at the London Bridge English village.  It's a real London phone booth, but no phone.

Linda& Marilyn at the London Bridge English village. It’s a real London phone booth, but no phone.

Today was basically a stay at home day.  Marilyn is officially “on retreat” and spent part of the day by herself reading and contemplating.  I made coffee for breakfast, as usual, and Linda made her amazing vegan cinnamon rolls for brunch.  They were brunch because they take hours to make and she did not feel like getting up early enough to have them ready by breakfast and we did not expect her to.

Butch dropped Fonda at church and then came back to get me on his way to the Big Tent RV Show.  Today was the last day of the show so I bought a 2″ wide roll of rescue tape and got three smaller rolls in the deal.  I bought more of the Carnu-B wax but the vendor was out of the Metal Shine cleaner.  That’s the risk one takes waiting until the end of a rally or show.  I also bought two small LEDs that looked like the might work in our spotter/downlights.  We then stopped by Mac McCoy’s booth to chat.  He was busy with customers but Charles Martin was there so we chatted with him instead.

We got back to camp just after 11 AM as Linda was putting the finishing touches on the cinnamon rolls and Marilyn joined us for brunch.  I tried one of the new LED bulbs but it would not fit in our fixtures.  I dealt with some e-mail and thought about spending the rest of the day writing but decided to work outside instead.  My outside task today was cleaning some of the bus windows using the Carnu-B Metal Shine to remove hard water stains.

Chris and Jim of Geeks On Tour did their weekly live broadcast from their rig and then started making preparations to leave.  We had two cinnamon rolls left so Linda took them over as a going away gift.  Charles and Connie Martin dropped in and a short time later Mara and her friend Michael arrived.  Marilyn came over followed by Butch and Fonda so we circled the chairs and had quite a gabfest.

Eventually everyone left and I returned to my window cleaning while Linda and her sister started preparing dinner.  Linda made her wonderful warm Farro dish with kale and dried cranberries while Marilyn made a shredded Brussels sprout dish with pistachios and dried cranberries.  Both dishes were excellent and the use of dried cranberries in each one tied them together nicely.

Linda and Marilyn went to the apartment to watch Downton Abbey but the satellite receiver was not activated so they worked on the jigsaw puzzle instead.  I stayed in the coach and took a call from Lou Petkus who had questions about RVillage.  I then consolidated my blog posts from the first seven days of October (2014) into a single post, selected five photos to go with it, and uploaded it to our WordPress site, the first post I have done since September 30, 2014.  If I do one consolidated post each evening I should be caught up to our arrival in Quartzite on December 12, 2014 in about two weeks.  After that I may go back to daily posts or continue to consolidate three or four days at a time.  I would like to be caught up and making current/daily posts by the time we pull out of here on March 1st.

London Bridge in Lake Havasu City (LHC), AZ.

London Bridge in Lake Havasu City (LHC), AZ.

2015/01/26 (M) A Plethora of Jims

We had toast and jam (strawberry preserves and orange marmalade) for breakfast along with our usual coffee and juice.  Jim A. called just after breakfast to update me on work we are doing for FMCA HQ.  Jim G. (&  Chris) pulled out yesterday.  Jim B. (& Barb) are here for the winter.  Jim L. (The brother of owner Joe L.) manages this place and stops by almost every day.  I think we have met several other Jims along the way.  When we meet someone new I just assume their name is Jim until I learn otherwise.  This winter has truly seen a plethora of Jims.

Jim and Barb let me know they were headed to Blythe, California to go grocery shopping and offered to pick up anything we might need.  Butch and Fonda also left but Larry and Sandy did not, which was unusual for them.  Linda and Marilyn wanted to walk around Tyson Wells so I drove them down to Kuehn Street and Central Avenue, stopping at the Post Office on the way.  I stopped on the way back at Herb’s Hardware store to get some 000 steel wool and then topped off my fuel tank at the Union 76 station.

Connie Martin visiting us at the Camp Liebherrvile / Brocker.

Connie Martin visiting us at the Camp Liebherrvile / Brocker.

Back at our coach I started assembling my blog posts from October 8 through 15 into a single post and selecting photos to go with it.  I do not like to sit and do this kind of work for long stretches of time so I got out my cleaning supplies and worked on the outside of some of the bus windows.  I tried using straight vinegar to clean them followed by rubbing with the steel wool, and tried it in the opposite order.  I decided to stick with steel wool first figuring the vinegar would help clean it off.  I did not apply wax to the outsides of the windows as I want them as clean as possible before I wax them.  Rain was forecast for today and it eventually started so I moved indoors and cleaned the insides of several windows on the passenger side of the coach.  These were clean enough that I used the Carnu-B spay wax that I bought yesterday on them.  The rain let up so I moved back outside and worked on the upper windshields.  I got both of them steel wooled and wiped down with vinegar and got a coat of wax on the driver side glass before it started drizzling again.  I put my supplies away again and headed back inside.  Linda called and asked to be retrieved so I drove back down to Kuehn and Central to pick them up.

Linda put out some hummus, chips, and grapes for lunch and we heated up the leftover Farro dish and divided it up between us.  Marilyn went back to the apartment to take a nap and Linda laid down to read and snooze while I continued working on e-mails and blog posts.  Gary Hatt, publisher of Bus Conversion Magazine, sent me several photos of himself standing in front of his Eagle.  I selected the one I thought would work best to go with his “Publisher’s Letter” in the January 2015 issue, post-processed it several different ways, and sent it back with an explanation of what did and why.  I also got the blog post for the second seven days of October completed and uploaded before dinner.

Mara Culp and Charles Martin visiting us at Camp Liebherrville / Brockner.

Mara Culp and Charles Martin visiting us at Camp Liebherrville / Brockner.

As the afternoon progressed the rain settled in.  Although not heavy, like a thunderstorm, it was steady well into the evening.  Jim and Barb returned and Marilyn eventually came back over to the coach.  That got Linda out of bed and working on dinner.  She made a dish that has become a standard; pasta with onions, garlic, mushrooms, and sun-dried tomatoes lightly sautéed in olive oil.  Instead of wheat noodles, however, she used “zoodles.”  Zoodles are long slender pieces of zucchini made with a hand operated SpiraLife spiral slicer.  They get added to the sauté just before serving and are simply heated rather than cooked.  We had a green salad with Ken’s Steak House Asian Sesame dressing, dried cranberries and pistachios.  We had slices of a sourdough baguette with pepper spiced olive oil for dipping and Linda and I had a glass of Franzia sangria.  Fresh strawberries for desert completed a nice meal.

Marilyn helped with the dishes after which she and Linda checked on the developing storm out east and then played Scrabble and other games while I stayed out of their way and worked on this post.  Hey, it’s a small kitchen.

The rain stopped at 7:38 PM but started again in earnest around 8:30 PM.  It was still raining at 9:15 PM when Marilyn went back to the apartment and the forecast said we could have rain overnight until 5 AM tomorrow.  We have had very little rain here this winter so I am sure this is welcomed.  It will be interesting to see if the precipitation triggers any sort of desert bloom tomorrow on our drive to Yuma or perhaps the following day.

Linda’s iPad battery was down to about 10% at 9:45 PM so she retired to the bedroom, where the charger is located, and continued to read for a bit longer.  I am usually very sleepy an hour after dinner but get my second wind a couple of hours after that.  I had an e-mail from Gary at Bus Conversion Magazine regarding the use of soft water in the Webasto-based Aqua-Hot in his Eagle and sent him a reply.  I then went through the article on Butch’s main engine air-compressor failure, finalized all of the changes, and uploaded it to our Dropbox along with the photo files.  I updated my BCM Article Status Sheet and uploaded it to the BCM folder in our Dropbox.  I then e-mailed Gary and editor Mike Sullivan to let them know that the new material was ready and available.  By the time I finished it was going on midnight.

 

2015/01/19 (M) The Big Tent

I got up at 7 AM, made coffee, and had some while Linda slept in.  I left at 8:15 AM and drove to Lloyd and Verda DeGerald’s motorhome on East Kuehn Street.  Lloyd was still there so I was finally able to purchase the Webasto flame sensor (photocell) I needed for our second/spare Webasto DBW2010.75 burner.  I then drove the short distance west on East Kuehn Street to the entrance of the Quartzsite Market Place camping area and drove in to the Eagles International rally.

This GM bus conversion tows a VW bus with matching paint.  I wonder if they use the VW to pull the bus out when it gets stuck?

This GM bus conversion tows a VW bus with matching paint. I wonder if they use the VW to pull the bus out when it gets stuck?

I grabbed some general purpose bus photos while Byron Pigg cleaned up the area around his bus so I could photograph the exterior for Bus Conversion Magazine.  While I was working Butch called to let me know he was almost back from Blythe and wanted to meet Gary, the owner/publisher of BCM.  Before Butch arrived Neal Sunderland, VE6NL drove up and looked over Gary’s MCI MC-9 Moose Creek Motor Cabin.  Gary was over talking to the GM bus owners but came back and had a long chat with Neal.  I exchanged contact information with Neal and we agreed to meet later at our coach so he and his wife could see it.

Eagle buses certainly make very nice motorhome conversions. This one was pulling out of the Eagles International rally at Quartzsite.

Eagle buses certainly make very nice motorhome conversions. This one was pulling out of the Eagles International rally at Quartzsite.

When I was done “working” I returned to camp and had a bite to eat.  I then transferred the photos I had just taken to my computer, organized them according to subject, and backed them up to our NAS device.  By the time I was done Linda was ready to go to the market area.

Quartzsite is a place with a sense of humor.  Central Ave I-10 overpass.

Quartzsite is a place with a sense of humor. Central Ave I-10 overpass.

Quartzsite is, metaphorically, a “big tent” but there is literally a Big Tent set up here that houses the Big Tent Sports, Vacation, and RV Show.  The Show started this past Saturday but today was our first chance to go.  Besides, our RV insurance agents (Charles and Chris Yust of C&C Marketing) had advised us at the SKP Happy Hour to avoid the weekends and come during the week in the afternoon.  Because traffic was so congested on Central Avenue heading south from Main Street to Kuehn Street we decided to walk the 1.4 miles from our coach to market area.  Along the way we ran into Mark and Emily Fagan.  They are photographers and writers and I recognized them immediately from Escapees Magazine and their blog.  We introduced ourselves and had a nice chat before continuing our separate ways.

At least they are in agreement about the size.

At least they are in agreement about the size.

We walked through the Big Tent, stopping at a few booths and quickly passing by many others.  There was a much higher percentage of non-RV vendors than we normally see at RV rallies, and significant duplication of others.  There were at least 18 vendors selling some kind of miracle pain reliever and a dozen vendors selling LEDs.  We did, however, spend some time with the TST TPMS vendor who was from the factory and will probably go back and buy a complete system from him.  We also stopped at the FMCA booth and chatted with FMCA President Charlie Adcock and ran into RVillage founder/CEO Curtis Coleman there.  We lingered awhile at the Carnu-B booth watching a demonstration of products for cleaning, polishing, and waxing the exterior of a motorhome.  We spent a few minutes at the Escapees RV Club booth and talked at length with the folks at European Motorhome Tours and The Ultimate Road Trip (Alberta, British Columbia, Yukon Territory, and Alaska).  If money were no object we would do the European Tours.  They are typically 30 days and sometimes more than 40 and include the motorhome rental, all of the overnight stops, admission to key attractions, and some of the meals.  The main added cost, besides flying there and back, are groceries and fuel.

Charlie Addcock, FMCA National President, in the Big Tent at Quartzsite, AZ.

Charlie Adcock, FMCA National President, in the Big Tent at Quartzsite, AZ.

Neal Sunderland called while we were still at the Tent and we agreed to meet him and Nora at our coach at 4 PM to see it and chat.  Lou called while we were visiting and we agreed to meet for dinner at 5:30 PM at Crazy Jerry’s.  We had vegan pizza and sat until almost 8 PM talking.  While we were there I got a call from Curtis Coleman of RVillage inviting us to drinks at the Quartzsite Yacht Club.  He was there with Patti and the Gulds (Chris and Jim).  The QYC is across the street from Crazy Jerry’s, so that was easy.  The Amber Bock on tap was very tasty and we were there until 9:45 PM.

 

2015/01/18 (N) The Desert Bar

Today was divided into several distinct pieces.  At 8:30 AM we connected Linda’s iPad to our Verizon MiFi and Facetimed with our son, daughter-in-law, and grand-daughter.  At 25 months her vocabulary is developing quickly and she recognizes us on the iPad as Grandma Linda and Grandpa Bruce.

The Nellie E. Saloon at The Desert Bar outside Parker, AZ.

The Nellie E. Saloon at The Desert Bar outside Parker, AZ.

When we concluded the call I made a quick run over to the Quartzsite Market Place to touch base with Gary Hatt and the folks at the Eagles International bus rally and the FMCA Western GM Bus Chapter rally.  I returned to pick up Linda and we chatted briefly with Jim Guld of Geeks On Tour.  He and Chris are staying at our encampment for at least this week.

Linda at The Desert Bar.

Linda at The Desert Bar, upper level.

We headed up AZ-95 to Plomosa Road and headed east into the BLM camping area to pick up Mara.  She is camped with the WINs (Wandering Individuals Network) but we drove past their camp and she flagged us down on the return.  We got a brief tour of her Fleetwood Bounder and then headed for the Desert Bar.  It was over 40 miles to get there with the last five on a primitive road that is not regularly maintained.  It was very rough in places but our Honda Element had enough ground clearance to handle it and 4-wheel drive was not needed.  It was, however, a slow drive.  There is also a network of rougher trails that ATVs use to get to the bar.

The lower level of The Desert Bar.  Lots of people for a Sunday afternoon.

The lower level of The Desert Bar. Lots of people for a Sunday afternoon.

One of the buildings that makes up The Desert Bar is the Nellie E. Saloon.  It is named after the mine that operated there at one time.  The bar began very humbly in 1983 and has grown considerably since that time.  It is the quintessential “let’s build it and see if they come” venture.  And come they did.  It is completely off-grid and powered mostly by solar energy, although we did see a propane tank which we presumed fuels the cooking grills.  Hours are weekends (Sat and Sun) noon to 6 PM from the first weekend in October to the last weekend in April.  We got there a little before it opened but there were already people there and by 1 PM there were at least 200 people milling around and eating and the live band started playing.  It was an older but active crowd, reflective of what we generally see around Quartzsite.  The Desert Bar has moved beyond famous and is now legendary.

Linda with our friend, Mara, at The Desert Bar.

Linda with our friend, Mara, at The Desert Bar.

The beer was canned but cold and fairly priced, especially considering the location.  We had veggie burgers that were tasty and cost $3.50 each.  We shared an order of garlic fries with Mara and they were excellent.  There were lots of other choices on the menu as well, so of which we could have had.  As we were getting ready to leave we spotted riders on horseback coming up the road so we stuck around long enough to photograph their arrival.  These were the original, 1 HP, ATVs of the American west.  We had a great time there and it was certainly a unique place and experience for us.

The dance floor at The Desert Bar.

The dance floor at The Desert Bar.

We left at 2 PM, stopped at the Wal-Mart in Parker, and got back to our rig at 3:30 PM. I dropped Linda off and headed over to Lloyd DeGerald’s place.  Verda was there but Lloyd had their credit card machine with him so I said I would come back tomorrow morning to buy the Webasto flame detector photocell.  I then headed back to the Eagles International and Western GM bus rallies to grab some general bus photos.

Linda and Mara enjoying the vibe at The Desert Bar.

Linda and Mara enjoying the vibe at The Desert Bar.

Gary and I touched base with Buck Bolding to get squared away with arrangements to photograph his Eagle later in the week.  We also walked over to the Western GM rally and made arrangements with Larry Hall to photograph his bus on Tuesday morning.

Byron Pigg and his wife Betty had straightened up their 1985 model 15 Eagle so I spent some time photographing the interior.  The rally was having a pot luck (carry in) meal at 4:30 PM and invited me to stay so I had some plain spaghetti and green salad.  While I was there I met Rico and Monica, a couple from Europe that have spent four months each winter for the last 15 years traveling around the world in a decommissioned Swiss military truck with a large trailer behind it.  Rico drives buses in Europe for a living and works enough hours in eight months to earn his full year’s pay, which gets paid out to him once a month all year long and making it convenient to fund their annual travels.  Gary and I chatted with folks until it was dark and I finally left to go back to my coach.

Patrons arrive at The Desert Bar on the original, 1 HP, ATV.

Patrons arrive at The Desert Bar on the original, 1 HP, ATV.

BCM publisher Gary Hatt (L) at the Eagles International bus rally at the Quartzsite Market Place drycamp area.

BCM publisher Gary Hatt (L) at the Eagles International bus rally at the Quartzsite Market Place drycamp area.

I spent the rest of the evening copying photographs from my camera to my computer and working on this blog post.  Somewhere in all of that I got a phone call from Lou Petkus of the SKP photographers BOF and we figured out a time/place to meet.

Sunset over 'Q' Mountain from the Eagles International bus rally site.

Sunset over ‘Q’ Mountain from the Eagles International bus rally site.

 

2015/01/16 (F) Making Contact

The Aqua-Hot came on a couple times last night for a few minutes and it was nice to hear that old familiar roar and know that it was working the way it is supposed to.  I need to see if I can put a new clamp on the hose that comes out of the middle zone pump.  I also need to shorten and re-route the tube to the expansion tank, but the burner/combustion process is finally working correctly for the first time in 3-1/2 months.  At some point Butch and I will try to figure out what is wrong with the other burner and fix it if we can.  I also need to make the same wiring/connector modifications to the second burner so it is plug-n-play interchangeable with the installed one.

Butch and Fonda decided to make a run to Yuma today.  He needed parts from Home Depot, Lowe’s, or Tractor Supply Company that he figured he could not get in Quartzsite, Blythe, or Parker, although Blythe has a good sized NAPA Auto Parts store.  We chose not to go this time for various reasons, not the least of which was that Linda’s sister is arriving on Thursday and Yuma, along with Los Algodones, Mexico is one of the places we want to take her.  But more immediately we wanted to meet up with Gary Hatt from Bus Conversion Magazine today and attend a get-together that Technomadia scheduled at Beer Belly’s for 1 PM.  I also received an e-mail yesterday that Lou and Val Petkus had arrived in Quartzsite so we are trying to arrange to meet up with them.  Lou is the head staff photographer for the SKPs Escapade in March and I am the assistant staff photographer.

Our out-and-about day, however, did not start until late morning so that left the morning open to get other things done.  As usual, Linda went for a walk while I started writing an article for BCM on the work we did yesterday on our Aqua-Hot.  Linda and I took lots of pictures and I think it will be a solid technical article when I am done.

We left at 11:15 AM and drove to the Quartzsite Market Place dry-camping area.  The entrance is on the north side of Kuehn Street east of Central Avenue (US-95) but is not easy to spot.  We stopped at the Too Crazy Ladies trailer and picked up our engraved SKP Ham BOF call sign tags and Rescue Our Cats sign.  We then took the back entrance into the RV parking area, which is just to the left of the TCL trailer.  It did not take us long to find Gary Hatt back with the Eagles International Bus Rally group.

Gary Hatt, publisher of Bs Conversion Magazine, recently acquired this Eagle bus conversion.

Gary Hatt, publisher of Bs Conversion Magazine, recently acquired this Eagle bus conversion.  We met him for the first time at this Eagles International Bus Conversion Rally in Quartzsite, AZ.  Linda is talking to Aqua-Hot service technician Lloyd DeGerald (left).

When we arrived Lloyd DeGerald was there with his assistant working on the Aqua-Hot in Gary’s recently purchased Eagle bus conversion.  Gary’s friend John was working on other projects on both the Eagle and the MC-9 Moose Creek Motor Cabin.  Lloyd determined that the Webasto controller was not functional and needed to be replaced.  He had a new one for $800 and a used one for $400.  Gary went with the used one and had Lloyd do a full service on the unit as well.  While the technicians were working on the Aqua-Hot Gary gave us a tour of both coaches.  By the time he was done with the tours Lloyd had the Aqua-Hot running very nicely.  Before he left I chatted with him about the photocell flame detector and he said he had one for me at a discounted price.

We walked around the market area visiting the vendor booths by the street to kill a little time and found a particular vendor open who had been closed the last few times Linda checked.  They had organic dried apple slices as well as organic dried veggie chips.  We bought a bag of the cinnamon apple chips and a bag of the veggie chips and had a few of each while we strolled.  We worked our way back to Gary’s buses by 12:45 PM, gathered him up, and walked over to Beer Belly’s “Adult Day Care” (outdoor bar) for the Technomadia RVillage get-together at 1 PM.  It took us a few minutes to spot Chris Dunphy’s signature black hat, as Beer Belly’s was crowded, but we finally did and joined the group that was gathered there.  They have also written articles for BCM but like us had never met Gary in person so I made the necessary introductions.

Beer Belly’s had Amber Bock on tap so Linda and I each had one.  We don’t normally drink at 1 in the afternoon, and beer is not normally my first choice if I am going to drink, but the sun was warm and the beer was cold and it was all good.  We stayed about an hour, chatted with some of the other folks that showed up, and then walked back to Gary’s buses.  We agreed to come back and pick him up at 5:30 PM and drive him to our campsite so he could see our bus and get away from the crowd for a little while.

L-to-R: Gary Hatt's Eagle, his MC-9 Moose Creek Motorcabin, and some of the other Eagle bus conversions at the Eagles International rally.

L-to-R: Gary Hatt’s Eagle, his MC-9 Moose Creek Motorcabin, and some of the other Eagle bus conversions at the Eagles International rally.

Given the timing of our social encounters we decided to have an early dinner.  I was using my iPad when the FedEx truck pulled in.  I went out to meet the truck but Barb beat me to it.  There was one package addressed to Butch so I figured it was the gauges from PartDeal.com but we left the box on a chair by the front door of their bus.  Barb indicated that someone named Jim was supposed to come work on something on Butch and Fonda’s bus and was going to park his motorhome onsite for a few days.  The generator bay door was open so I wondered if Butch was having a problem with the genset.  If so, he had not mentioned it to me.

For dinner Linda made white rice with greens and things and heated up some mock orange chicken she has had in the freezer for a while.  It was a relatively quick and easy meal to prepare but very tasty.  We were just starting to eat when a familiar looking SUV pulled in with two kayaks on top.  It was Chris and Jim Guld of Geeks On Tour.  I knew Jim wasn’t here to fix a generator but was pleased to find out that they were checking out of the Scenic Road RV Park tomorrow and moving in with us for the next week.  We have known them for a few years but never really had a chance to just socialize in a relaxed setting so we are looking forward to a little quiet social time with them.

I left a little after 5 PM to fetch Gary and John and drove by the DeGerald’s motorhome first to buy the photocell flame detector but they were not there.  We were back at the coach before it got dark and I had just enough time to give them a tour of the bays.  It was chilly so we went inside and gave them a tour of the interior.  We had a little wine or beer, as suited individual tastes, and just sat and visited.  All too soon I had to drive them back.

Butch and Fonda pulled in around 8 PM.  We were getting concerned about their dogs only to discover that the dogs had traveled to Yuma with them.  I chatted briefly with Butch and a little while later he brought over our turbo boost gauge.  We turned in early as we are headed to Lake Havasu City very early tomorrow morning.