Tag Archives: exercise walking (Linda)

2015/10/31 (S) Boo!

Leave a reply

We overslept a bit this morning and did not get up until 7:20 AM.  We dressed quickly and drove to breakfast separately as we had to go to separate places afterwards.  We got there at 8 AM and had a nice chat with the folks at our end of the table.  It was a big group this week, at least 24 people, maybe more.

Linda left breakfast at 9:15 AM to meet Diane at Kensington Metropark at 9:30 and go walking.  I lingered at the restaurant until after 9:30.  I drove back to I-96 and Grand River Avenue in Brighton, where I filled my fuel tank at the Shell station, and had a nice QSO with Mike (W8XH) while driving.  I then drove across the street to Brighton Ford to pick up the four spin-on coolant filter/conditioners I ordered yesterday.

Brighton Ford’s parts department is a NAPA outlet but they do not have any signs to that effect as Ford Motor Company won’t allow it.  My next stop was up Grand River Avenue towards Howell at the O’Reilly’s Auto Parts store where I picked up the nine (9) gallons of Chevron Delo 100 SAE 40 engine oil I ordered yesterday morning.  I drove home and chatted a bit more with Mike on the way.  I found out that he gets his Lawn tractor serviced at/by Sloan’s in Linden and is very pleased with them.  He has a trailer for transporting his lawn tractor and is willing to let me borrow it to transport ours when I am ready.

When I got home I unloaded the oil and filters and then emptied the dishwasher, refilled it, and started it.  I then went to my office to work.  I had an e-mail reply from Byron Pigg with information I needed to finish the article for Bus Conversion Magazine (BCM) about his 1985 Model 15 Eagle bus conversion.  I incorporated the new info into the Word docx and then called Byron on the phone.  We spent at least an hour going over the article and chatting about bus conversions.  After we wrapped up our conversation I worked a bit longer on the article making the last few edits and removing blemishes from two of photos.  I uploaded the article (Word docs) and all of the photo files (jpgs) to my BCM Dropbox folder at 2:15 PM and then e-mailed Gary (publisher), Mike (editor), and Jorge (layout).

Shawna gets Madeline into her Bumblebee costume for Halloween Trick-or-Treat in their neighborhood.

Shawna (back to camera) gets Madeline into her Bumblebee costume for Halloween Trick-or-Treat in their neighborhood.

While I was doing all of that Linda firmed up our Halloween plans with our son.  We left the house at 2:45 PM and drove to Ann Arbor, arriving at their house around 3:30.  Shawna got Madeline into her bumblebee costume and Linda gave her a Halloween gift bag with a rag doll, some candy, and a card.  At 4:15 we walked over to a neighbor’s house for a gathering that included snacks/dinner.  We talked to host Laurel’s parents, Tom and Kendra, who were there from San Diego, California.  All of the kids and most of the adults left at 5:15 to go door-to-door trick-or-treating on Granger Street.  Granger was closed off to vehicles for several blocks with policeman at each barricade and there were hundreds of people out and about.  Many of the adults were in costume, some quite elaborate, and it was quite a sight.

Madeline caught on very quickly to her role in all of this and would often walk past other, larger children right to the front of the line to get her treat.  She is just shy of three years old so it was cute.  One of the houses had two large pumpkins out front, appropriately carved.  They were real pumpkins and each weighed about 1,500 pounds when they were delivered by a truck.  Madeline is above average height for her age but these pumpkins towered over her.  The homeowners are well known in the neighborhood for having these giant pumpkins each year and bring in mind-boggling large quantities of candy in crates.  You gotta love neighbors like that.

The rain held off for most of the prime trick-or-treat window from 5 – 6 PM but I was cold and went back to the house a little ahead of everyone else.  It started to drizzle around the same time Madeline’s endurance was waning and they got back to the house at 6:30 with the umbrella deployed.  Madeline was eager to take stock of her Halloween “loot”.  We enjoyed watching her excitement at having different items to choose from and then “negotiating” with her parents over having to select just one item for this evening.  Halloween trick-or-treat is perhaps best appreciated while watching a three year old experience it.

We left around 7 PM and stopped at the nearby Whole Foods Market for soy creamer.  We picked up two bottles of Frey brand wine, a white and a red, and two pieces of vegan cake.  Frey makes organic wines without the use of animal products and are a sponsor of “Cooking School” with Christina Perillo on the PBS Create channel.

I got a call from Joe as we were getting ready to leave Whole Foods.  He was packed and ready to hit the road first thing in the morning.  He wasn’t sure if he would make it all the way to our house on Sunday or finish the trip early Monday morning.

It rained on the drive home and I took the wheel as Linda has a hard time with dark/wet roads.  We were reminded, once again, of the poor condition of Michigan’s roads, many of which need to be repainted and have reflectors installed such as the ones we saw in Florida the winter before last.  (I suspect that the reason Michigan does not use them is because of snow plows, but they really make it safer to drive dark roads at night.)  We got home sometime after 8 PM and had dessert.  I checked the bus for leaks buy did not find any new water.  I texted Joe our address, checked e-mail, and then opened the package from Rockler Woodworking that our postal carrier had delivered earlier in the day.

The maple veneer from Rockler was a bit darker than I had hoped, but it will still be a nice contrast to the walnut trim when suitably finished.  The two shelf brackets were certainly substantial enough but it remains to be seen if the wall of our coach is adequate to support the table without a leg to the floor.  The main issue will be the fasteners near the top which will be in tension and trying to pull out of the wall.  Of secondary concern will be the lower tip of the brackets, which will be in compression, trying to push through the wall and possibly puncturing it.  I may have to use expanding bolts or toggles rather than screws for the upper (tension) fasteners.

We had some hot tea and went to bed.  Although I did not get to work on the bus today I got a lot accomplished and we had a great time watching our younger grand-daughter experience Halloween.

 

2015/09/29 (T) Bus Windshields

Leave a reply

Today was windshield day.  A week or so ago Chuck made appointments for both us to have windshields replaced on our buses by the local Safelite franchise.  Chuck knows Scott, who now has a management position with the company, and arranged the work through him.  The appointment was nominally from 8 AM to noon so Chuck was at his shop before 8.  We figured it would take a while for the crew to do his two lower windshields so I got up around 7 AM but did not have coffee or breakfast.  I finished yesterday’s blog post and then went through my final departure tasks starting at 8:30 AM.  I texted Chuck at 8:45 AM and pulled out of our driveway at 8:50 AM, figuring that was late enough to miss most of the morning traffic headed into the northwest corner of the Detroit metropolitan area.  Chuck texted back that I could take my time as the crew had not shown up yet.

The first raindrops came as I was pulling out of our driveway.  As I pulled out onto Hacker Road I had a clear view of dark clouds to the northwest.  Although my destination was 20+ miles to the southeast I headed north towards M-59.  The shortest route would have been south, and gotten me quickly onto pavement, but there are some low branches before the road ends at Grand River Avenue so I do not go that way.  From Hacker and M-59 the shorter route would have been east to US-23 and then south to I-96 but that interchange is a left exit, left entrance in the middle of an extensive construction zone; not the sort of thing I wanted to deal with in the bus.  So I waited patiently for a break in the traffic and then headed west on M-59 towards the storm clouds.  A guy heading east had to slow down while I pulled out a flipped me off as he went by.  I hope he had a nice day.

I encountered heavier rain as I traveled west for about four miles.  I turned south onto Latson Road and drove away from the rain, reaching I-96 about four miles later.  I headed east on the I-96 and had an easy drive all the way to Beck Road with only an occasional raindrop.  Even at this hour of the morning there were traffic slowdowns along the way but no parking lot traffic jams.  The Beck Road exit was easy to navigate going south and it was equally easy to position myself for the left turn onto Grand River Avenue.  About a mile and a half later I pulled into the parking lot for Chuck’s shop and phoned Chuck to let him known I was there.

I knew in advance how he wanted me to position my motorcoach but there were enough vehicles parked in various places that I wanted him to spot for me.  I lifted the tag axles, pulled up to the building, and then turned hard to the right.  I backed around to the driver’s side to get somewhat parallel to the building and then started angling towards the passenger side.  There is space next to the building in front of Chuck’s shop directly across from his large (bus size) overhead door.  My objective was to back around into that space and then pull forward steering hard to the left to get lined up with the door.  I have done this before and managed to do it again with Chuck’s assistance.  Our Prevost H3-40 VIP conversion is surprisingly maneuverable with the tag axle lifted off the ground.

There were two Safelite vans there when I arrived and Charlie and Eric were already busy working on Chuck’s lower windshields.  Chuck had backed his coach into the shop so I could pull in nose first and get the front end out of the rain if needed.  Since there were only two guys, and the removal and installation of one of these windshields is a two man job, I just parked my bus outside and shut it off.

I called Linda at home but did not get her so I tried her cell phone.  She was at Kensington Metropark walking with Diane.  She said we had heavy rain at home before she left and that it was moving towards the shop.  I could see the dark clouds to the WNW and it eventually rained bucketfuls, albeit for only a brief time.

A couple of years ago Chuck and I went together and bought five lower windshields from Prevost for our H3-40 VIP coaches, two for him and three for me, for the ridiculously low price of $125 each.  They were shipped to his shop in a big triple set of cardboard boxes with foam spacers on a pallet and have been sitting there waiting for us to find someone to install them.  Chuck decided to use both of his, in part because there were stone chips in the current ones, and in part because he is vacating his shop and needed to reduce the amount of stuff that has to be moved and stored.

The existing windshields on Chuck’s coach both cracked rather badly when they were removed, as in multiple dozens of fractures, but did not shatter.  Safety glass is a wonderful thing.  He was not planning on keeping the old ones but it was obvious that removing a windshield in order to install a new gasket with the idea of reinstalling the glass was probably not possible.  Charlie and Eric removed the old gaskets and then cleaned off the frames.  Chuck’s old gaskets had been slit at the corners by a previous installer, probably to make it easier to get the gaskets over the glass, but should not have been altered in that way.

Chuck had new gaskets and spline material so the guys got one of the new gaskets installed on the frame.  It looked like it would be too big but by the time they got it pressed fully into place it was a perfect fit.  They lubricated the gasket and set the new windshield in place.  After working the top of the gasket over the top edge of the glass they slid the windshield from the outside edge all the way towards the center pillar.

Chuck and I were both hungry and thirsty.  Since Charlie and Eric were working on his coach I took Chuck’s suburban to Panera for coffee, a muffin (for Chuck) and a bagel (for me).  I made the trip twice.  I was almost there when I realized that I did not have my wallet and went back to get it.

The guys finished installing Chuck’s windshields and went to lunch.  We did not leave as we had no idea how long they would be gone.  It turned out to be about an hour.  When they got back I had Charlie look at my two lower windshields.  The passenger side was cracked and definitely needed to be replaced.  The driver side had two small rock dings but they were not directly in front of the driver’s seat and not near an edge so I decided to only replace the passenger side lower windshield at this time.

I started up the bus, pulled the nose into the shop, and lowered the suspension to make it easier for the guys to work on it from the outside.  I pulled in far enough to make sure the front part of the roof was completely inside the building as it is lower than the rest of the roof and slopes forward.  I lowered the rear more than the front to make sure any rain that hit the portion of the roof that was outside the building ran to the sides and rear rather than forward and down the windshields.

To remove my windshield they removed the spline that locks the glass into the gasket and then managed to get the glass and gasket out as one assembly.  The glass already had a 10″ crack when they started and was fractured in 100 places by the time it came out.  They cleaned off the frame, which had a lot of crud on it, and then put the new gasket on.  The gasket for the lower windshields is reversible and is used on either side.  It is not rectangular, however, with the vertical edge by the center pillar being longer than outside edge where the glass wraps around into the A pillar.

With the gasket in place they installed the windshield by using large suction cups to pick it up, front and back side, and setting the bottom edge into the gasket with the right edge about four inches from the center pillar.  The passenger side mirror was in the way so I had to loosen one of the set screws and swing it out of the way.  They used a hard plastic stick with a rounded tip and edges to get the gasket over the outside of the top edge of the glass.  Using glass cleaner as a lubricant they then slid the glass towards the center and into the gasket channel.  The glass did not slide easily but Charlie and Eric were big, strong guys and it eventually was in place.  They then used the plastic sticks to get the gasket out from behind the glass and over the edge all the way around.  The last step in the installation was to put Sikaflex adhesive caulk between the frame and the gasket and between the gasket and the glass, all from the outside.  They masked off the frame to protect the paint but did not mask off the glass.  Gasketed glass installation was not something I knew anything about so it was informative to be able to watch every detail of this process.

They had our invoices with them but had to have the office redo mine and e-mail it since I only had one windshield replaced instead of the two we originally scheduled.  Chuck and I each wrote them a check.  Eric had us sign on his Note tablet and printed our receipts on a portable wireless printer.  It had been six hours since they arrived and they had spent five of those working pretty hard.  We gave each of them a $20 tip.

Charlie and Eric loaded up our three old broken windshields and left.  I then backed my bus out and parked it.  Charlie wanted it to sit for at least an hour before driving it to let the Sikaflex cure a bit.  Chuck locked up the shop and we went to Panera (again) for a late lunch.  We both had Black Bean Soup and Chuck had a half sandwich.  Barb called as we were finishing our meal and said she was her way to the shop so we headed back.  She arrived at the shop just ahead of us and inspected the new windshields on their coach.  I then showed her the work we have done on the interior of our coach.  We sat around in the shop talking while I waited for the worst of the rush hour traffic to pass before driving the bus back to our house.

I called Linda around 5 PM and then left for the drive home, reversing my route from this morning.  Traffic was heavy but moved along.  Linda heard me pull in the driveway and helped get me positioned.  It’s hard to sneak up on someone with a Detroit Diesel 8V92 engine.  Once I was parked I shut off the accessory air to the engine bay, disconnected the chassis batteries, and plugged in the electrical shorepower line.  Back in the coach I noticed that the refrigerator had come out of the alcove about 12 inches.  It had not budged on the drive to/from Edwardsburg and Elkhart but I will obviously have to secure it after all.

Dinner was reheated chili and Saltine crackers.  When Linda makes chili she always makes extra and freezes it to have on hand for easy heat and serve meals.  It is a one pot meal the way she makes it and is as good, or better, left over as it is fresh.

Ferman had called while I was gone and let Linda know that he had the Sandstone Corian he needed to build the small table for the bus so after dinner I texted Josh to let him know.  I then checked e-mail but did not respond to any.  We watched NCIS and NCISNOLA on the big TV in the basement and then went to bed.

 

2015/09/23 (W) Autumnal Equinox

Leave a reply

We were up at 8 AM, had granola for breakfast, and enjoyed our coffee in the living room by the fireplace.  I like cool mornings.

I spent some time yesterday morning, and again this morning, considering my full-frame DSLR options.  The only 50 MP “35mm” DSLR camera body on the market at this time is the Canon 5Ds/R and there is no indication that Sony plans to introduce a successor to the A99 anytime soon.  The A99 is still available, as is the vertical battery pack/grip and I am at the point where I will probably order one.  It has a 24 MP full-frame CMOS sensor, which is double the resolution of my alpha 100.  More importantly, it will accept all of my old 35mm Minolta A-mount lenses and they will work as designed.

Linda left at 9:40 AM to meet Diane at Kensington Metropark.  I gathered up the laundry, sorted it, and started the first load.  I then settled in at my desk for a while.

I e-mailed Mike (W8XH) to see if he could assist me on Saturday and/or Monday with climbing the tower to do some more antenna work.  I then e-mailed Bill Gerrie to see if he and Karen were in Michigan yet.  I pulled up the initial mockup of the October 2015 issue of Bus Conversion Magazine and proofread my article on replacing the speedometer.  Jorge had done a good job of laying it out.  I e-mailed back four minor corrections, one slightly larger one, and a general comment about the lack of space following periods.  I had an e-mail from Steve Smith (N8AR) with contact information for Yaesu Fusion technical support.

The washing machine beeped so I transferred that load to the dryer and started another one.  I noticed that it was after 11:30 AM so I cleaned the cats’ litter tray, grabbed the garbage from under the kitchen island sink, put it in the trash can, and got it to the street.  Alchin’s normally comes “around noon” but I had a feeling they had already driven by.  They were still in our subdivision, however, and stopped on the way out to empty our can.

I had another cup of coffee and updated this post.  By noon Linda had not called yet let me know she was on her way home so I headed to Lowe’s for a roll of plumber’s sandpaper.  I also picked up the paste we need to hang the new wallpaper.  On the way back to the house I stopped at Teeko’s Coffee and Tea to order some Cafe Europe half-caff blend.  Linda was home when I got back and we had a light lunch.  We have both finally taken off some of the weight we put on this past winter.  Long, hard work days with little or no lunch seem to help.

By the time we got back to work on the bus projects it was 3 PM.  It’s hard to make progress when the workday starts in the afternoon.  Today is the autumnal equinox, so it gets dark much earlier in the evening than it did in late May, June, July and even most of August.  Still, as anxious as I am to get the heat exchangers re-installed we have to deal with the wallpaper in that part of the bus first.  Linda helped me assemble the right desk base, repeating what we did yesterday with the left base.

The left pedestal base with the Aqua-Hot fan-coil heat exchanger mounted inside.

The left pedestal base with the Aqua-Hot fan-coil heat exchanger mounted inside.

We installed the metal grates on the air openings (from the inside) and then used doubled-sided tape to affix the plastic mesh to the metal grate.  We put a 1/2″ plywood spacer in the bottom and marked the locations of the mounting bracket holes and the heat exchanger.  We took the exchanger and spacer out, punched the starter holes, and drilled.  Linda cleaned the heat exchanger and used a pair of tweezers to straighten the bent radiator fins, of which there were quite a few.  We cleaned off the two copper pipe stubs that provide the inlet and outlet for the antifreeze and then attached the self-stick 3/8″ X 1/4″ dense foam weather-stripping around the front of the housing.  We mounted the exchanger to the spacer with approximately 1/8″ of the foam weather-stripping beyond the front edge of the spacer.  We put the spacer/exchanger assembly back in the base and I secured it with screws while Linda pulled it into position, compressing the weather-stripping.

Linda cleans and straightens the fins on one of the fan-coil heat exchangers.

Linda cleans and straightens the fins on one of the fan-coil heat exchangers.

I took a few photographs as we worked and took some more of the finished assemblies.  While we were working we got a call from Philip Jarrell of Precision Paving.  Phil was calling to see if we still wanted the French Drain and driveway work done.  He has been busy all summer and even more so coming into fall when folks decide they need stuff done before winter.  He had given us a quote (estimate) back in the spring but could not do the work then because the soil was way too moist.  The property has dried out nicely over the last seven weeks and he wanted to make sure he did the work yet this year if we were still interested.  I told him “yes” and he said he would call “Miss Dig” right away to get the utilities marked and then get started.

The two desk bases with the fan-coil heat exchangers installed view from above and behind.

The two desk bases with the fan-coil heat exchangers installed view from above and behind.

I think this annoyed Linda as it will be another significant expenditure, but it’s something I think needs to be done and it is not easy to get a slice of Phil’s time.  (Actually, we have done a lot of difficult work together on the bus this summer and I think she was already annoyed from working with me on the right base.)  Not taking advantage of Phil’s availability would likely mean a two-year delay in getting this work done.

This project is actually a combination of two different projects that happened to make more sense to do at the same than at separate times.  The French drain is intended to dry out the far west end of our property which has standing water in the spring and after heavy rains, and stays moist/soft for the first half of the summer.  There are a lot of trees in that area and we have lost some and are losing others.  The driveway work will give us additional parking for people visiting in their RVs and create the main approach to the location for the bus barn that I hope to eventually build.  The topsoil that Phil pulls out from the driveway will be used to fill in low spots on the west end of the property, further improving the drainage in that area.

The right desk base viewed from above/behind showing the fans mounted on the back side of the heat-exchanger.

The right desk base viewed from above/behind showing the fans mounted on the back side of the heat-exchanger.

Linda returned to stripping wallpaper in the bus while I folded the laundry and put it away.  For dinner we had a salad and more of the soup that Linda made yesterday.  After dinner Linda researched wallpaper installation while I worked at my computer and uploaded eight blog posts from the third week of July.  About the time I finished the last one Brendan called so I went upstairs and Linda put the call on speaker.  He is a couple of weeks into his position at Eastern Michigan University teaching Art History and gave us a status report on how it is going, along with news of how Madeline is doing in her new daycare program University of Michigan.

We watched Dr. Michael Greger’s 2015 nutrition research summary on Linda’s iPad.  This is an annual presentation that he does at the vegan Summerfest in Pennsylvania.  His theme this year was the top health concerns of Americans, based on a major survey that was done by one of the national survey organizations, and what nutrition research has to offer with respect to these.  As we already know, many different diseases, one common answer; whole-food, plant-based, nutrition with no animal products.  We really are what we eat, and Americans are now some of the least healthy people on the planet.  We went to sleep reaffirmed in our dietary choices.

 

2015/08/24 (M) Skimcoating

Leave a reply

For a change of pace we had granola with vegan yogurt for breakfast.  I made seven cups of the Cafe Europe / Columbian decaf blend but Linda only had one mug as she was meeting Diane at Kensington Metropark at 9 AM to walk.  After she left I gathered up the laundry, sorted it, and started the first load.  I then turned my attention to the bus.

My first task was to cut one of the 8″x8″ sheets of #80 sandpaper in half, put it on the orbital pad sander, and go over all of the Universal Patch and Skimcoat (UPS) that I applied yesterday.  The 80 grit worked well and I only needed the one half sheet.  I swept the floor clean of loose debris and then assembled my tools and materials to patch a few gouges I missed yesterday and then skimcoat the entire portion of the floor that used to have ceramic tile on it.  I mixed 24 ounces (by volume) with 12 ounces of water (by volume), half as much UPS as I did yesterday.  I tried to work more quickly and got most of it applied.  I cleaned up my tools and let them dry while the compound cured.  That also gave me an opportunity to move laundry from the washer to the dryer and start another load in the washing machine.

I had a call from Chuck so I took a break to chat with him.  He and Barbara spent the weekend racing at the old Air Force base in Oscoda, Michigan.  Their bus and race car both ran well and he turned in some very good times.  He had installed a new turbo boost gauge in the bus and based on my experience had selected a 0 to 15, PSI VDO unit.  Apparently 15 PSI is not high enough for his engine.  I have seen the boost on my gauge, which is a 0 to 30 PSI model, go as high as 17, but not often.  For most of our trip to Arizona and back this past winter it did not go over 15 PSI.

The only issue they have with their coach at the moment is their old Amana residential refrigerator.  The freezer is apparently not keeping things as cold as it should and the ice maker is not working.  They use a lot of ice and generally have the freezer stocked, so those are problems.  They bought a bag of ice for the weekend but it appeared to get warm enough to develop surface moisture and then refroze into large chunks, inconvenient at best.  I think they have decided to replace it and want to do so before they leave for the winter and while they still have the shop and the forklift.

Chuck is also going to contact the glass installer and see if he would be willing to install bus windshields.  Both of his lower windshields need to be replaced as do both of ours.  We have five replacements at his shop, two for him and three for me.  I also have new gaskets but he needs to get two sets.  We discussed late September as the best time for me and he will see if the windshield guy will do all four of them on the same day.

I mixed the remaining USP, about 12 ounces (by volume) with 6 ounces of water (by volume) and finished the skimcoating of the bus floor.  I used the last little bit of compound to patch some screw holes and small gouges in the living room floor where carpet had been installed.  There may be a few more but instead of opening another bag of UPS I will probably return it and buy a quart of the premixed compound.  I then cleaned up my tools again and left them in the sun to dry.

Linda got home about this time.  It was just after noon, so we had a light lunch of vegan deli slices with lettuce, onion, and Daiya non-dairy cheese, on thin buns.  A pluot provided a nice, sweet finish to lunch.

We measured for wallpaper the other day so I took the notes and created an Excel spreadsheet to figure out how many rolls of wallpaper to order.  While I did that Linda worked on cleaning and reconditioning drawer fronts with Touch of Oranges and Touch of Beeswax.  After examining the wallpaper in the bathroom (of the bus) I think we need to replace it too.  We took a few minutes to get those measurements and I added them to the spreadsheet.

The wallpaper we have selected is the Lamar (#699-3377R) from the Just Textures collection of Sellars and Josephson.  It is an off-white color with a small texture pattern designed for reverse hang, random match installation.  It is only sold in 2-roll bolts 27″ wide and 4.5 yards long.  We will need more than six rolls to replace all of the wallpaper so we will have to order eight rolls even though we may defer doing part of the hallway and the bathroom for a while.  Fortunately it is not too expensive (as wallpapers go) and is scrubable, which was one of our requirements for use in the bus.  Linda will return the sample books to Delux Drapery and Shade Company in Ann Arbor on Wednesday morning and place the order.

Linda reheated the leftover fajita veggies from last night and fixed some white rice to go with them.  We had fresh strawberries and a little Coconut Bliss non-dairy ice cream for dessert.  Coconut Bliss ice creams are not too coconuty, and are appropriately named.  They are as good as I remember Hagan-Daas being.

I took a little time to add lines to my floor tile layout drawing showing the location of the underlayment sheets.  It looks like I may need at least eight sheets.  I have four sheets in the garage and will install those before buying more.  I spent the rest of the evening working on the article for Bus Conversion Magazine about Larry and Carol Hall’s GM4106 bus conversion and finished it around 10 PM.  I spent another 1.5 hours catching up on e-mail and checking in on the status of Technomadia’s bus renovation project at MasterTech in Elkhart, Indiana.  The weather has turned cool and should be perfect for working on the bus tomorrow.  We need to have long, productive days, so I had a snack and got to bed at midnight, played a few games, and went to sleep.

 

2015/08/18 (T) Walking Grind

Leave a reply

We were up at 8 AM and I made a pot of Ethiopian Yirgacheffe half-caff coffee while Linda got breakfast ready.  She made a batch of granola yesterday so we had some with fresh blueberries and unsweetened soy milk.  It’s our standard breakfast, but that’s because we like it so much.  She had an e-mail from Robin at the bakery and had to deal with some issues related to the bakery’s new account, The University of Michigan Ann Arbor.  As I do most mornings I sat in the living room working on my iPad, drinking my coffee, and paying attention to our two cats.

Being Tuesday Linda had a date with Diane to walk at 10 AM and left at 9:30 for Kensington Metropark.  I continued working on my iPad for a while and enjoying my coffee.  At 10:15 AM I called the Livingston County Sheriff and reported the mailbox incident from late Friday evening /early Saturday morning.  Shelby took the call, was very nice, said she was not aware of any other mailbox reports, but would pass the info along to the Desk Sargent.  I checked my e-mail and confirmed with Harvey for Friday at 10 AM to move the old bus refrigerator.  I finally went out to work on the floor of the bus at 11 AM, by which time the outside air temperature was already in the 80’s.

I leave three of the awning style windows in the bus open a few inches so it doesn’t get too hot inside.  I opened all three roof vents, turned on their ceiling fans, and set them to exhaust air rather than draw it in.  I also left the entrance door open to allow more air to flow through the inside of the coach.  I then sanded and vacuumed until about 1 PM.  When I came back in the house I had two missed calls from Michele Henry of Phoenix Paint so I called her back.  I was on the phone with her when Linda got back from her walk.

Once I wrapped up the call with Michele we had a light lunch of hummus with pita chips and both black and red grapes.  While we were eating we were entertained by a gray squirrel who had gotten onto the bird feeder and was hanging upside down by its hind legs.  It would curl its body to bring its mouth up to the bottom of the feeder, emancipate some seed, and then uncurl to the more relaxed stretched out position and eat it.  All of this was also being watched with both interest and considerable skepticism by three crows who were hanging around on the ground under the feeder.  They grabbed seeds that the squirrel dropped but seemed very wary of it, which surprised us.  I speculated that perhaps they had never seen a squirrel behave in this way and were, therefore, understandably and appropriately cautious; crows are very smart, after all.

After lunch we took the three wallpaper sample books to the bus to look at them with the woodwork.  Before we could do that, however, we discovered a small bird trapped in the coach and had to deal with it.  I say “trapped” because it was up on the dashboard and obviously confused by the windshields as it kept trying to fly out through them.  It did not realize it could get out the same way it came in, through the open door.

The bird seemed small and I think it was an immature sparrow but I’m not sure.  It was seeking safe shelter in the space between the dashboard cover and the lower driver side windshield.  I used a broom to try to gently encourage it to fly towards the door but it was understandably suspicious of my good intentions.  I put on a pair of canvas work gloves and it allowed me to gently pick it up.  I tried to release it at the door opening and it flew into the door causing Linda to make a comment about why we use the phrase “bird-brained.”  I caught it again, got outside the bus clear of the door, and tossed it gently away from the bus.  It immediately took flight and flew off to the southwest, apparently none the worse for its ordeal.  I can only image the story it told the other birds.

I got a piece of the Armstrong Alterna Luxury Vinyl floor tile from the garage.  Many of the wallpapers that we thought would look good with the floor tile turned out to be too yellow, and most of the ones with good color tone were too dark, but we found a few that we liked.  Those tended to be lighter without a lot of pattern and a neutral, off-white color.  We are, however, far from a final choice as we do not currently have a sample of the Lambright Notion Linen upholstery fabric or the MCD night shade material and the wallpaper has to work with all of these simultaneously.

We measured the areas that need to be repapered and in the process decided that we would leave the old wallpaper on the inner wall of the hallway, at least for now.  (The paper in the bathroom, which is different from the rest of the coach, is generally in good condition and we are not currently planning on replacing it as part of this project.)  The existing wallpaper in most of the coach is a string cloth with a beige base but distinct vertical threads that contain a noticeable amount of grey and a more subtle herringbone pattern.  It looks good with the walnut woodwork and worked well with the old white carpet, black ceramic floor tile, and bone leather upholstery, so we think it will continue to look good with the new floor tile.

If Josh is at his shop tomorrow we will try to stop and pick up the Lambright Notion Linen sample as whatever wallpaper we choose has to work well with the furniture fabric.  On Thursday we will revisit the papers in the three books we currently have with an eye towards something that has some grey in it.

It was another warm, humid day and I was done sanding so I closed up the roof vents, locked up the coach, and went inside.  Linda prepared a pizza using the gluten-free crust recipe she got from Mara.  Yum.

After dinner I went to Lowe’s and bought two bags of TEC Skill Set Universal Floor Patch and Skim Coat, a mixing bucket, two bags of tile spacers, and three 4’x8′ sheets of 1/4″ SurePly underlayment.  I meant to buy a folding metal sawhorse but left it somewhere in the store.  I was going to buy premixed floor leveling compound but they only had 1-quart containers for $10 each and the directions said it would only cover 1.5 square feet.  I have about 80 square feet of floor to patch and level, so that clearly was not a good solution.

The Universal Floor Patch is a powder that has to be mixed with water, but each bag will cover 20 – 25 square feet at 1/8″ thickness and costs $13; much better than the premixed stuff.  I have a few areas to patch that are deeper than 1/8″ but the material can be applied up to 1/2″ thick per coat, and most of the area just needs a much thinner skimcoat.  It can also be sanded within 24 hours which will allow me to make it very smooth and keep the work moving along.  My goal is to have the floor leveled and sanded smooth by bedtime on Saturday so I can install the 1/4″ underlayment on Sunday and start laying tile on Monday or Tuesday next week.

I stopped at Teeko’s Coffee and Teas to get some more of the Cafe Europe half-caff blend.  They had the regular blend but not the decaf blend so I had Roger use the Columbian decaf instead.  He roasted the beans for me while I waited and Jeff showed up along with his wife as I was leaving.  They were married last September and are expecting their first child late next month.  Jeff was wearing his Pepsi delivery shirt, confirming what the woman at the Kahuna Coffee Shop told us last Friday.

We turned in early as we will be getting up very early tomorrow to drive to Indiana again.  Linda watched an episode of NCIS after which I watched a PBS special on the origins and evolution of the Navy Seals.

 

2015/05/25 (M) Memorial Day

Leave a reply

We spent the morning lounging around drinking coffee and enjoying the holiday.  Hey, even retired people need a day off.  Actually, we continued to research refrigerator, seating, and upholstery options for the bus, taking a break to have a tofu scramble and toast for breakfast.

We stumbled upon the Yale Appliance blog which proved to be very informative.  Yale is a very large appliance store in the Boston area and maintains a blog about appliances.  After reading what they had to say in some fairly recent postings we realized that we should probably not be looking for a “counter depth” refrigerator.  It also appeared that our best bet in terms of case dimensions and interior volume might be a standard top freezer design and our best bet in terms of both price and reliability might be a Frigidaire.

We went to the Frigidaire website and found that the FFHT1621QB might fit our needs perfectly.  It is a 16.3 cu. ft. top freezer design available in black, white, or stainless steel with doors that can be hinged left or right.  (We need a fridge with doors the hinge on the left.)  It is 28″ W x 30-1/8″ D x 64-3/8″ H and only needs 3/8″ clearance on the top and sides and 1″ in the rear.  The depth includes the doors and handles; the depth of the case alone is only is 26-5/8″.  Our refrigerator alcove is 33-3/4″ W x 29-1/2″ D x 66-3/4″ H so it will fit easily, recessing a bit more than our current 22.6 cu. ft. Jenn-Air and leaving 5″ to its left for a pull out pantry.  The pantry will have be custom built and measure approximately 5″ W x 28″ D x 66″ H including top and bottom mounted slides/guides.  Also of importance, we will not have to modify the cabinet above the refrigerator alcove.

In terms of seating we checked out Gilbreath Upholstery’s website but then concentrated on the Bradd & Hall website.  Bradd & Hall is a well-known RV (& marine) furniture supplier in Elkhart, Indiana.  They handle the Flexsteel RV and marine product lines and also sell the Lambright Comfort Chair product line, although the latter is available directly from Lambright in Shipshewana, Indiana.  We have sat in the Lambright Lazy Relaxor Lite swivel recliner (wall hugger) at RV rallies and found it nicely sized and very comfortable for us.  It is 24″ W x 33″ D x 38″ H and needs 2.4″ clearance from the wall.  It is normally a free-standing chair so we are unclear whether it can be secured to the floor or be used with seat belts.  We plan to visit Bradd & Hall on Monday, June 1 before we check into the GLAMARAMA rally and this is one of the things we will ask about.

Bradd & Hall also sells a Flexsteel Barrel Chair with a bolt down pedestal base that locks in different positions and includes a bar for attaching seat belts.  It is 26″ W x 30″ D x 34″ high and might be a better fit for our bus and what we are trying to accomplish with our remodeling project.  Last, but not least, they sell Flexsteel Captain’s Chairs (which Flexsteel calls “bucket seats” on its website).  We need a chair of this type to replace the oversized front passenger chair and possibly to replace the driver’s chair.  My hope, however, is to get an ISRI 6800 seat for the driver’s position.  These are the seats that are normally installed on tour buses.

An advantage to getting everything from Bradd & Hall, except for the ISRI driver’s seat, is that we can get the same fabric on the passenger Captain’s chair and living room chairs and buy additional materials to have the seat and back cushions made for the sofa that I will build (with storage underneath).  We will probably find a folding chair for the desk and can have the seat recovered in the same material so that everything is coordinated.

Linda called the J. C. Penney’s salon to see if Renee was working and had openings.  She was, and she did, so Linda booked a time, grabbed her car keys, and headed to Twelve Oaks Mall.  That seemed like an opportune time for me to head to the bus to double check measurements and ponder design solutions.  I checked the dimensions of our refrigerator alcove and the Frigidaire FFHT1621QB will definitely fit very nicely.  The front part of the passenger side of the bus has 13′ 3″ of flat floor space available for a desk and two chairs with a small dining table between them.  On the driver side of the bus the aft end of the sofa nook is 7′ 2″ from the entrance step.  If I can fit both chairs and the table in the first 7′ 2″ on the passenger side we will have room for a 6′ long desk that is 26-1/2″ deep.  That’s long enough to have a file drawer on one end and a printer shelf on the other end with plenty of room in between for a chair.

We have been planning on reusing the Corian top from the old dinette table so I decided to disassemble the top from its base.  I had never really looked at the construction before now and discovered that the Corian is glued to a wood panel that is secured to the two massive posts that are screwed to the base.  I was able to disconnect the base from the posts easily enough but there did not appear to be any way to separate the Corian from the support structure.  I took a few whacks at it with a pry bar and small sledge hammer and it was clearly not going to come loose.

The good news is that we can now select a new table top in whatever size, shape, and material suits us and use the same material for the desk top, which will double as additional kitchen counter space.  Our assumption has been that we will use Corian, but Corian is heavy so we will consider other options before making a final decision.  We discussed extending the desk top all the way down the wall to the front of the living room, although it would only be about 6″ deep at most, and building shallow cabinetry to go under it and fill in the space above the HVAC chase and below the window trim.  That space will essentially be wasted otherwise, and have to be finished in some way, so building small storage spaces is worth considering with or without the extended desk top.

What all of this comes down to is that we have to select the two chairs we want to use in conjunction with figuring out the table size and support system, and then finalize the design of the desk.  We plan to recondition all of the woodwork (with Touch of Oranges and Touch of Beeswax) and replace the refrigerator before we install the new floor, which has to go in before the furniture.  That’s the order in which decisions have to be made and the work has to be done.  Chairs and custom woodwork are potentially long lead items so we need to get them finalized and ordered, but they are the last things to get installed, so it should work out OK in the end.

It rained hard for a brief time mid-afternoon, after which Linda went for a long walk.  She was walking almost daily this winter in Quartzsite, Arizona but has not walked much since we got home.  That gave me time to work on this blog post.

Earlier in the day we snacked on nuts instead of having lunch.  Linda made whole wheat capellini for dinner using the Portobello mushrooms and some of the asparagus we bought yesterday at the Howell Farmers Market.  It was delicious.

I had intended to work at my computer most of the day but that obviously did not happen.  When I finally went to my office after dinner I had a long chat on the phone with Butch about hardware for the slide out pantry and other bus-related things and then checked a few websites that he suggested as good sources of specialized hardware.  I then e-mailed GLCC members about parking with the chapter and took care of some other e-mail.  In addition to computer-based work I need to keep working on the bus but I am also at the point where I need to order some things and then settle in and work on drawings for the desk, pantry, and sofa.