Tag Archives: Chevy Colorado – GMC Canyon

2015/05/18 (M) Ceramic Floor Tile

Leave a reply

I plugged my laptop in, started it, put a load of laundry in the washer, and then made our morning coffee.  We are finally running out of the six pounds of beans we had shipped to us in Quartzsite, Arizona at the end of February and will need to get more from Teeko’s sometime soon.  While we were enjoying our morning coffee I pulled up some information online on how to remove ceramic floor tiles.  What I found was a bit discouraging but what was clear was the need for certain equipment and safety precautions.  Linda needed to return the Sherlock DVDs to the Howell Library today so we went on an errand run to Howell.

At the Library we did some more vehicle research in the April 2015 Consumer Reports.  The Chevy Colorado / GMC Canyon mid-size pickup truck was Motor Trend Magazine’s 2015 Truck of the Year, but being a new model CR had no data on predicted repairs or user satisfaction.  Ditto for the 2015 Ford F-150 and its 700 pound lighter aluminum body.  We liked the size of the Nissan Frontier but the manual transmission required for four-flat towing behind our bus will keep us from buying one.  We have not looked at the Colorado/Canyon yet but it is similar in size to the Nissan Frontier.  CR gave good marks to most of the Subaru models and the Forrester was one of their top picks.  Years ago we wanted a Subaru Outback but they were always just slightly too expensive.  Compared to the vehicles we have been looking at recently, the Subaru’s are less expensive.  Right now, however, we are focused on the utility of a 4-door pickup truck.  Yeehaa!

We checked out the DVDs for Season 1 of the British detective series A Touch of Frost. It is not a BBC production so we will see how we like it.  We stopped at D-R Electric Appliance Sales and Service just up the street to look at refrigerators.  We bought our new gas range/stove from them last September.  They had a 16 cubic foot top-freezer GE (GTE16GTHxx) whose dimensions looked like they might work.  With the doors removed it was under 26″ deep so it would fit through the door of the bus sideways.  It is available in white, black, and stainless steel.  Kurt Richards helped us and said he would search the units he can order if I give him the dimensions of our enclosure.  D-R Electric Appliance is not a dealer for Fisher and Paykel so we would have to get one of those through Lowe’s if we decide to go that route.

Lowe’s was our next stop.  Linda looked at plants but decided not to buy any on this trip.  We picked up a couple of 40 W appliance bulbs for the microwave as one of the two bulbs that lights the top of the range burned out the other day.  I picked up a new face shield, dust masks, a Tyvek jump suit, a floor chisel with shield, and a 3-pound short-handle sledge hammer.

Teeko’s Coffee and Tea is kitty corner from the Lowe’s/Walmart shopping center so we stopped there and ordered one pound each of our three half-caffe blends: Sweet Seattle Dreams (Seattle Blend + Sweet Dreams decaf blend); Ethiopian Yirgacheffe, and Cafe Europe.  Jeff wasn’t there but his mom (Mary) took our order and his dad (John) was starting to put together the roast when we left.  I will pick the beans up tomorrow afternoon.

By the time we got back to the house it was time for lunch so Linda fixed grilled “cheese” sandwiches.  She is still using up the non-dairy cheddar cheese we bought a while back.  It is not Daiya brand and it does not taste like cheddar.  Actually it doesn’t taste like much of anything.  Keith was there mowing the yard as we thought he might be.

Me in the Tyvek jumpsuit removing the black ceramic floor tiles. (Photo by Linda.)

Me in the Tyvek jumpsuit removing the black ceramic floor tiles. (Photo by Linda.)

[p1 L] It was once again 1 PM by the time I got to work in the bus removing the black ceramic floor tiles.  I suited up and Linda took a couple of photos.  I was over dressed under the Tyvek jumpsuit so I changed into something cooler.  Even then it was a hot, sweaty afternoon.  Houses get wrapped in Tyvek to prevent air movement between the interior and exterior, so a jumpsuit does not really breathe.  Neither did I with the dust mask in place so I settled for my wrap-around safety glasses, full face shield, Tyvek jumpsuit, and leather gloves.

I had hoped to get most of the floor tiles out intact.  They are nice 12″x12″ black ceramic with a hint of silver flake in them and they were probably expensive when they were installed in the bus in 1990-91.  They were installed just the way they would be in a house, on a troweled bed of thin set mortar, with one difference; they were set directly on the factory original plywood subfloor of the bus rather than on an underpayment layer.  The information I found online this morning indicated that removing tiles installed this way might require removal and replacement of the subfloor.  That is not an option in the bus so I was curious, and a bit nervous, to see how they would come out.  The other caution was to NOT smash them with a sledge hammer to break them into smaller pieces for easier removal, even though there are lots of websites that tell you to do this.  Ceramic tiles with a high quartz content will shatter sending tiny razor sharp shards flying in every direction; thus the Tyvek jumpsuit, face shield, and gloves.

I took a few tiles out yesterday and most of them came out intact.  The first few today, however, came out in two or more pieces.  Either way I was committed to removing them, so I kept at it.  I developed a technique that seemed to work more often than not.  I would chisel along one free edge and when I got the first indication that the tile was loosening I would switch to an adjacent free edge (if there was on).  Proceeding in this manner I was able to work my way down a row getting most of the tiles loose in one piece.  The tiles were laid in rows with aligned joints running across the coach and staggered joints running the length of the coach.  Thus the rows were short and easier to work on, my work was interrupted by something I will describe next, but I returned to the task and removed the tiles from the entire kitchen/dining area back past the refrigerator.  This part of the deconstruction will take a while but based on the progress I made today it will not take as long as I thought it might, all things being equal (which they never are).

While I was working Keith came to the bus in need of some assistance.  His zero-turn Hustler mower had quit moving and started smoking and was stranded in the northeast corner of our yard.  This particular mower is all hydraulic; the gasoline engine simply turns a hydraulic pump and fluid pressure is used to drive/steer the mower and turn the cutting blades.  Keith had oil on his arms and needed some paper towels.  He suspected a hydraulic hose had failed and the smoke was from the hot oil.  The immediate problem, however, was to get the mower back into its trailer some 400 feet away.

Keith got the mower stuck once last year in wet/soft soil along the north property line.  I was able to use our Cub Cadet lawn tractor to pull him out then so we figured we would try that again.  Just this past weekend I had charged the starting battery and moved the lawn tractor outside to make room in the garage for the furniture we took out of the bus.  It complained for a moment and then started up.  Keith had tow straps so I drove it over to his mower and we hooked the straps to the trailer ball on the back of the lawn tractor.

Keith’s mower weighs 1,200 pounds.  I doubt that our Cub Cadet weighs half that much even with me sitting on it.  I was able to pull it part way across a level-to-slightly-downhill part of the yard but once we hit an upslope my back tires started to slip.  Keith went to get Linda because the lawn tractor would stop if I got off and I was too far from the house to conveniently jump start it.  I continued to drive while Linda helped Keith push although we should have figured out a way to trade places.  It was very hard work for them but the Cub Cadet proved to be “the little engine that could” and we got the mower down by the third culvert (where the driveway for the barn is supposed to go).  We chose that location because it was downhill and close to Keith’s truck and trailer.

Keith’s trailer has a large rear ramp and pointed front like the bow of a boat with smaller ramp that opens at an angle on the driver’s side.  I tried pulling his mower up the rear ramp into the trailer.  The plan was for me to drive out via the front ramp.  Unfortunately the Cub Cadet could not maintain enough traction.  We unhooked it and I drove out the front and put it back in its parking spot.  I got a pair of wheel chocks from our bus and placed them in front of the trailer wheels while Keith unhooked the trailer from his truck.  He then attached the tow straps to the trailer ball on his truck, brought them I through the front ramp opening just off the nose of the trailer, and tied them around the front frame of the mower.  It took a few tries, and one repositioning of the strap on the mower, but Linda and I were finally able to guide it into the trailer while Keith pulled it up the ramp with his truck.

Linda got water for all of us while I helped Keith reload the trailer.  Keith is retired and doesn’t mow lawns for the money.  He’s a good guy who charges us a very reasonable price for the service he provides and we were glad to help him get his mower back in his trailer so he could go home, take a shower, and have a cold beer.  We should have done the same, but he probably took the trailer someplace to have the mower fixed and we both went back to what we were working on.

By 4:30 PM I was too warm and too sweaty to remove any more tiles.  I was also at the point where I was starting down the hallway and needed to remove some quarter round base molding that was installed over the edge of the tiles.  Tomorrow I plan to work earlier in the day when it is cooler, but I say that every day.

Linda cooked most of our dinner on the outdoor grill using the grilling mat to cook potatoes, zucchini, and Japanese eggplant that had been sliced in half lengthwise.  She also made Farro and served it as a side dish.  I think that is the first time she has done that; she normally uses it as an ingredient.  While the vegetables were grilling we sat quietly on the back deck enjoying the last of the first bottle of 2013 Egri Merlot we bought at Whole Foods last week.  The robin eggs in the nest under our deck have hatched so we are trying not to disturb the parents too much.  They need to fly back and forth constantly to feed their young but are understandably weary of us.

I had a call after dinner from Darin Hathaway, the Aqua-Hot technician who worked on our unit in June 2014.  It appeared to have an intermittent ignition coil then and would not fire at all when I had the bus a Butch and Fonda’s in the fall.  Butch and I replaced the burner in October 2014 with the one I bought from him.  That burner was running rich until I replaced the blower bearings while we were in Quartzsite.  Old bearings = slow fan speed = inadequate air supply = rich air:fuel ratio = inefficient combustion and sooty/smoky exhaust.  I still need to repair the original one but for now that is not a priority.  Darin said he could bench test/repair it but Lloyd DeGerald has the same capabilities.

Butch had eye surgery this morning at a clinic in Indianapolis.  I will call tomorrow and see how he is doing.  Linda is having a girl’s day out with our daughter tomorrow, Jack will be here to clean the carpets on Wednesday, Linda has to go to the bakery on Thursday, and I have to take the cats to the veterinarian Thursday afternoon.  I also expect Keith will return sometime this week to finish mowing the grass.  Saturday morning will be our usual ham radio club breakfast and Linda invited Steve and Karen for dinner on Saturday.  Somewhere in there we will probably go look at the Chevy Colorado (GMC Canyon), Toyota Tacoma, and the Subaru Forrester and Outback.  In between all of that I will be doing a load of laundry or two, working on the bus floor, and trying to figure out refrigerators, furniture, and wall treatments, so it is shaping up to be a busy week.  Heck, it’s going to be a busy summer, and maybe a busy fall.

 

2015/05/16 (S) Trucks and Buses

Leave a reply

To paraphrase, “If it’s Saturday we must be in South Lyon” and that was, indeed, the case.  Most of the regulars were missing from our weekly breakfast gathering of the South Lyon Area Amateur Radio Club (SLAARC), but six of us showed up and had a great conversation.  By the time we headed towards home it was starting to rain lightly.

We stopped at Brighton Honda to get some information on the Honda Ridgeline pickup truck.  The salesman was very nice, but unfortunately Honda has stopped making the Ridgeline.  They are reintroducing it in the fall of 2016, but we will likely make a decision about a new car/truck sooner than that.  There are still a few in stock around the country but we already have an orphaned Honda Element.  We like the car, but would be happier if they were still being made.  In this case, however, it was a moot point as the Ridgeline is not towable four wheels down.

We drove next door to Brighton Ford to look at F-150 pickup trucks.  We were assisted by Frank Stapleton and he was easy to work with.  He insisted that we meet his new car sales manager, Eric Wilkinson, before we left.  We felt that was unnecessary at this stage in the process, but he also seemed like a nice enough guy.  The entry level XL 2-door may be reasonably priced (not really, but what car is?), but the slightly nicer XLT 4-door short bed with 4-wheel drive, towing package, and off-road package looks like it would price out at $45,000 give or take three grand.  Without X -Plan pricing that is simply not going to happen, and even with X-Plan pricing it is not a sure thing.  Frank really wanted us to test drive one but given the rainy weather we were not in the humor to do that today.

The F-150 is a nice truck, nicer in fact than many cars, and perhaps nicer than a pickup truck needs to be or should be.  On the plus side it certainly has ground clearance, but on the negative side (for us) it is also BIG.  The back seat room in the four door body style is cavernous, made larger by fold up seats, and that would be very useful for us when traveling in the bus.  Between the back seat and the bed we could store a LOT of stuff.  It has well-placed handles by all four doors, and it is a god thing as we both needed them, along with the running boards, to get in and out.  There are several engine options including the 2.7 L and 3.5 L Eco-Boost models, both of which feature twin turbochargers.  These are high-tech engines, with incredible power and torque and decent fuel economy. I liked the sound of that, but unfortunately that technology comes at a significant price premium.  Interestingly, Ford is using an aluminum body and the truck weighs in at about 4,700 pounds.  Our Honda Element weighs over 4,000 pounds and it is not nearly as big as the F-150.  How well the aluminum will hold up is unknown.

We were almost home when we decided to keep driving and visit LaFontaine Nissan.  While not as convenient as the Brighton dealerships, it is only 15 miles from our house, 13 of those headed east on M-59.  Linda checked their hours on her phone and they were open until 4 PM.  The purpose of our visit was to look at the Nissan Frontier pickup truck and the Nissan Xterra SUV, both of which Edmonds.com suggested were viable off-road alternatives to a Jeep Wrangler while Consumer Reports indicated they were more reliable and more practical than a Jeep Wrangler.  Bobby Lundwall, the Commercial Manager, assisted us and we met the General Sales Manager, Don Poley, before we left.  Bobby was very helpful and brought a Frontier and Xterra around front for us to see.  Again, we were not interested in test driving one at this stage, especially in the rain.

The Nissan Frontier pickup has an available 4-door, 4-wheel drive, short bed model.  It is considered a mid-size truck and is noticeably smaller than a Ford F-150 in every way.  The Pro-4X off-road version has 10.1 inches of ground clearance at the differential, which should be adequate for our needs.  It has a transfer case but is only towable four wheels down with the 6-speed manual transmission.  We looked at the Xterra but found it harder to get in and out of, especially the back seat.  It is taller than the Frontier and after due consideration we agreed that we were not really in the market for an SUV.

The Frontier does not have the bewildering array of options that the F-150 has and would be more suitable for the 95% of our driving that is on local paved and dirt roads.  It would be perfectly adequate for hauling materials from Lowe’s to the house and has an available tent option for camping.  We presume that aftermarket bed covers, canopies, and even small truck campers are available but we would check on that before buying one.  Ditto for Blue Ox base plates and the ability to install an SMI Air Force One auxiliary braking system.

We did not test drive one, but it was easy to get in and out of, and comfortable to sit in, at least in the front seats.  It weighs about 4,500 pounds, basically that same as the much larger F-150.  The only negatives at this point are the manual transmission and lack of choice on interior fabric; the Pro-4X only comes with a charcoal interior, either cloth or leather.  The bottom line was that it is probably a better fit for us than a Jeep Wrangler or a Ford F-150 and could be acquired for under $35,000 equipped the way we want it.  Nissan also has zero percent financing available at the monument, although that is often in place of other incentives.  The fact that it requires a manual transmission to be towed four wheels down, however, probably knocks it out of contention.

Storage compartment under the lift-up bed platform. The two boxes concealed and protectd 4" flexible HVAC ducts.

Storage compartment under the lift-up bed platform. The two boxes concealed and protectd 4″ flexible HVAC ducts.

Once we got home we had a light lunch.  I then changed into my work clothes and got back to work deconstructing the inside of our motorcoach.  (I like the term deconstructing as I think it is more descriptive of what I am doing that demolishing or even disassembling.)  My goal for today was to finish removing all of the carpet and all of the carpet tack strips.  I accomplished all of that except for a piece of carpet on the wall behind the driver’s seat and a piece on the front wall of the entry stairwell.  My first task, however, was to cut a short slot in the 3/8″ plywood filler that was under the dinette in order to free an AC electrical cable that ran through it and then through the floor.

Getting the carpet off of the sides of the bed platform was interesting.  There was a piece of wood trim installed along the top edge of the side of the bed base facing the front of the bus and just under the plywood bed platform.  The trim strip is rabbited on the underside and conceals a 12VDC strip light that is tied in with toekick lights in the bathroom and the floor lights in the hallway.  The power for the lights comes from inside the bed base through a small hole in the plywood and carpet.  The trim strip also appeared to be installed over the carpet and needed to be removed to get the carpet loose along the top.

Under-bed storage compartment with bot HVAC ducts uncovered.

Under-bed storage compartment with bot HVAC ducts uncovered.

There was also an adjustable HVAC louver on each side of the bed.  The louvers were installed from the outside and had flexible heater ducts slipped over them on the inside and secured with screws.  The flexible ducts were in the storage area under the bed and were covered by wood boxes to protect them.  The boxes, in turn, were carpeted to match the rest of the storage compartment.  To disconnect the wiring for the strip light and remove the boxes I had to first empty out all of the stuff stored under the bed so I could get in there to work.  The bed platform is hinged about one foot from the head end and the foot end lifts up, supported by two gas struts, so there was plenty of room to work once I emptied it out.

I have disassembled enough of the bus at this point to have some idea of how the conversion was built.  The cover “boxes” for the flexible ducts were actually half-boxes with a long side and top and one small end.  They were installed into a corner using a cleat screwed to the floor that the bottom edge of the long side was then screwed into.  There was a similar arrangement to catch the free edge of the top and it was screwed to the inside wall of the platform base.  All of these screws were put in through the carpet that covered the boxes and were essentially invisible so I had to find the screw heads by touch and back them out.

The area just forward of the bed base with the bed platform raised and facing the driver side of the bus.

The area just forward of the bed base with the bed platform raised and facing the driver side of the bus.

Once I got the protective boxes loose I discovered that the floor and wall were also carpeted.  There was a small bump out in each rear corner that served as wiring chases for AC electrical outlets on each side of the bed, and these bump outs were carpeted.  It seemed clear to me that the HVAC ducts, which are part of the OTR HVAC system, may have originally been installed directly into the HVAC chase outside the bed base and later repositioned to the sides of the bed thus requiring the louvers, flexible ducts, and cover boxes.  They also greatly reduced the available storage space under the bed.

The OTR HVAC chase runs along the floor-wall junctions on both sides of the bus for most of the length of the coach and a 12″ section of it is accessible on either side of the bed.  Removing the two flexible ducts, sealing up the openings, and installing the louvers outside the bed platform will free up additional storage space under the bed which is a good thing as we can always use for storage space.  That’s a nice bonus but adds some additional work to the remodeling project.  Such is the nature of remodeling; you never really know what you have until you have completed the deconstruction phase.

The aft side of the bed base. There is not a lot of room to work in here so I will remove the bed platform when I install the new tile floor. I plan to use the same tile on the sides of the bed base.

The aft side of the bed base. There is not a lot of room to work in here so I will remove the bed platform when I install the new tile floor. I plan to use the same tile on the sides of the bed base.

It was overcast all day with humidity near 100% and rained off and on into the evening.  It was also warm so I kept opening the roof vents and running the fans to make it more comfortable in the coach, but every time I did it started raining shortly thereafter.  When I was done working on the bus for the day I moved the ten concrete blocks that had been supporting the propane tank for the whole house generator and pulled up the utility marker flags for the underground gas line to our meter.  Keith will be here to cut the grass this coming week and I want him to be able mow these areas.

Linda spent the afternoon thoroughly cleaning the kitchen.  She also prepared a sugar-water solution, filled the hummingbird feeder we bought at Lowe’s the other day, and hung it off the railing of our rear deck.  A hummingbird found it almost immediately which was very cool.  For dinner Linda made pan-grilled tofu slices with caramelized onions and sweet BBQ sauce served on tortillas.  She also sautéed fresh broccoli and sliced up some fresh strawberries and pineapple.

After dinner Linda went to the Edmonds.com website to see if she could get a better feel for dealer cost and Fair Market Value for the Ford F-150 and Nissan Frontier.  While she was at it she looked up the Chevy Colorado (GMC Canyon), and Toyota Tacoma.  The Chevy Colorado was Motor Trend Magazine’s 2015 Truck of the Year.  Both the Colorad0/Canyon and Tacoma are mid-sized pickup trucks.  Toyota’s full-size pickup is the Tundra.

Brendan called while we out to see if Linda could sit with Madeline tomorrow night while he and Shawna had dinner with their friend Jorge.  Depending how the day goes tomorrow I may go to Ann Arbor with her.  We had two episodes of Sherlock left to watch and the DVDs have to go back to the library on Monday, so we watched both of them this evening.  It was a double feature so I made popcorn in-between episodes.