Tag Archives: B&H Photo (NYC)

2015/10/25 (N) Bus Dinner

Leave a reply

It was 44 degrees outside when we got up this morning but cozy in the house.  We were out of Linda’s homemade granola so we had oatmeal for breakfast.  It’s a nice change of pace on occasion and was a hot, hardy start on a chilly day.  I made a pot of Sweet Seattle Dreams coffee and we had a quiet morning in the living room.  We talked about going to the Howell Farmers Market, as today is the last day of the 2015 outdoor season, but did not need anything and given the temperatures decided not to go.  I changed into my work clothes at 10:30, went out to the bus, and turned up the thermostats to raise the interior temperature.

My focus in the bus today was tasks that I could not do alone.  I got my 15/16ths closed-end ratcheting wrench and removed the main retaining nut from the driver’s seat and from the front passenger seat.  Each of these nuts threads over a vertical stud that is fixed to the pedestal/riser which is in turn bolted to the floor.  In between the top of the riser and the bottom of the 6-way power base is a ball-bearing swivel plate which is centered on the mounting stud.  To get to these nuts I had to move the seats forward using the motorized bases and reach in from behind but I had good access and the nuts were not hard to loosen and remove.  I bought this closed end ratcheting wrench specifically for removing/installing these seat mounting nuts and it was worth every penny I paid for it.

With the nuts removed I unplugged the 12V DC power supply wires to each seat.  Linda and I were then able to lift the seats off of the pedestals without too much difficulty, carry them back into the kitchen (of the bus), and lay them down on their backs on the floor, which was protected with blankets.

The reason for removing the seats was two-fold:

  1. We were going to hang wallpaper on the living room walls where they merged into the cockpit and needed better access to those areas, and
  2. I plan to tile the floor and walls in the cockpit and entry this coming week and needed these seats out of the way in order to be able to do that.

Our next task, preparatory to hanging wallpaper, was to remove the walnut cover (half box) from the front eight feet of the passenger side OTR HVAC duct and wiring chase.  We set it across the two seats we had just removed to get it out of the way.

Bruce marks a piece of wallpaper on the dining room table in the house before cutting it.

Bruce marks a piece of wallpaper on the dining room table in the house before cutting it.

When we were finally ready to start wallpapering we needed three relatively short pieces; two to finish the driver side and one to finish the passenger side, at least as far as we intended to go.  I made a sketch for the shape of each piece, took measurements, and added them to the sketches.  The wallpaper is 26.5″ wide on the roll and the longest piece we needed was only 24″.  I got the 3′ and 6′ rulers from the shop while Linda got the roll of wallpaper.  We used the dining room table in the house to measure, mark, and cut each piece.  Although relatively small these pieces took some additional, careful, attention because they had to fit over, under, and around cabinets and window trim.  To make the installation easier I trimmed away as much of the waste material as possible before hanging the piece.

Linda partially filled two 5-gallon buckets with water, added soap to one of them, and brought them out to the bus while I retrieved the paint tray and liner and the 6″ pasting brush.  We laid out all of the wallpaper tools, put a towel on the floor, and set the paint tray/liner on the towel.  I poured the amount of wallpaper paste I thought we would need into the tray and started with the piece of wallpaper at the right end of the built-in sofa (towards the front of the bus).

As we had done previously everywhere else in the bus I applied the paste to the wall rather than to the back of the wallpaper.  The wall behind the sofa had been primed but the small strip above/behind the end cabinet and around into the cockpit had not been, so I used more paste in the unprinted areas.  This first piece required a lot of trimming so it took a while to hang but it looked good when we were done.  As I got each piece installed, with Linda’s help, she rolled the seams and then washed off the excess paste with a large sponge using the soapy water followed by a second sponge with clean water.

We continued along that wall towards the front of the bus with the second piece.  It did not require as much trimming as the first piece and went in a little faster and easier.  I overlapped the thin strip above/behind the cabinet with the first piece and cut through both of them to create a clean, tight seam.  When we hung wallpaper in our house many years ago all of the seams were done by overlapping adjacent panels and cutting through both pieces.  The paper we are using in the bus, which is actually vinyl, is installed by butting the factory edges together.  This certainly simplifies installation, and speeds it up a bit, but it is harder to get a perfect seam.  Still, it was the right choice for our motorcoach as it is washable and scrubbable and goes very well with the interior.

On the passenger side of the coach I pasted up the last section of the living room wall and part of the small section of wall under the trim on the window next to the front passenger seat.  I ended up cutting off a small part of this piece and installing in separately as the trimming required was intricate and awkward to do.

After installing the two parts of this third piece we decided to go ahead and paper a small triangular section of wall above the bottom window trim.  I got a scrap of wallpaper from the house that was big enough to cover the right triangle shape and cut it approximately to size.  I pasted the wall, set the bottom edge flush to the sill, pressed the back edge into its vertical corner, and trimmed off the excess.  This little section of wall was capped by a piece of walnut that ran at an angle along the bottom edge of the glass.  I trimmed off the paper at the bottom edge of the wood trimmed and tucked the paper in under the walnut.

The reason we did not wallpaper all of the small wall section below the window is that part of the plywood wall is severely water damaged and a piece of it rotted and is missing.  There is no practical way to replace the plywood and the only practical way to repair this area is to panel over it.  We could use thin plywood and wallpaper it but we have enough of the 1/4″ walnut veneered plywood that we salvaged from the old refrigerator to panel this area.

We were done with the wallpapering by 2:30 PM.  Linda cleaned off most of the tools and then took the two buckets of water out of the bus to pour them out and clean them.  I took the paint tray/liner, pasting brush, and some of the tools to the laundry room and cleaned them.  There was very little paste left in the tray liner so I had estimated quite closely on the amount I needed for today’s work.

The swivel mechanisms for the two front seats consist of two rings separated by ball bearings and interlocked around the inside edge.  They have an ‘A’ side and a ‘B’ side and one of them was installed ‘A’ side up and the other ‘B’ side up.  They also have a large washer.  The driver seat was installed with the washer between the swivel bearing and the power base.  The passenger seat had the washer directly beneath the retaining nut inside the power base.  Given these differences I could not tell the correct orientation and order of assembly by casual inspection of the pieces involved.  It is possible that the swivel plates are, in fact, symmetrical and thus can go in either way, but one of the washers had to be in the wrong place.

My interest in all of this was motivated, in part, by the fact that both of these seats have always wobbled since we bought the coach.  The new seats are firmly attached to the power bases which seem tight but may have some play.  I was suspicious of the swivels, however, as the main source of the play.  I studied the design for a while and came to some tentative conclusions.

When the swivel plates are installed the ring on the bottom (that sits on the pedestal) is not going to move as the pedestal is bolted to the floor.  The top ring, which will be in contact with the power base, is going to move relative to the fixed bottom ring when the seat is tuned.  I decided that the larger ring, which wraps around the inside edge of the smaller ring, should go on the bottom.  With regards to the washer it seemed to me that it should go directly under the retaining nut, allowing the power base to swivel relative to the nut without loosening it.  Further, placing it between the swivel plates and the power base would potentially prevent the base from fully resting on the swivel plate and allow the whole seat to wobble.

I will examine all of this again more carefully when we are ready to reinstall the seats.  For now, I took the two swivel bearings to the garage to clean and lubricate them.  After wiping them off I sprayed them with WD-40, worked them around, and wiped them off again.  I then sprayed them with garage door lubricant, worked then around again, and wiped them off.  Finally, I worked Red Tack ‘grease’ into the ball bearing race, spun the rings to distribute it evenly, and the wiped the outer surfaces clean.  After cleaning the grease off of my hands I took the swivel plates back to the bus, wiped the pedestal plates clean, and set them back in place.

We quit working around 3 PM so Linda could cut my hair and beard.  I then shaved, showered, and got dressed for dinner.  Linda showered after me but was dressed and ready to go before I was.  We made plans yesterday to meet Bruce (W8RA) and Linda (K4YL) at Carrabba’s in Novi at 5 PM for dinner.  We left at 4:30 and arrived in Carrabba’s parking lot just after 5.

The parking lot was not full so we knew there would not be a wait for a table.  Bruce and Linda were already there and had opted for a booth.  The booths will seat six adults so they have more table space than a table for four. They also offer a bit more privacy for conversation in an otherwise not very private setting.

Carrabba’s had changed its menu since we were last here.  The one dish they had before, Tag Pic Pak (seriously), was no longer on the menu.  It was Linda’s favorite dish and one of only two that we could eat.  They had something with a different name that the waitress said was the same but it included chicken.  She said they could leave the chicken out but the price would still be $14.95.  The Tag Pik Pak was $10.95 as I recall.  We have come to resent paying for animal products that we don’t eat.  Linda ended up getting whole grain spaghetti with Pomodoro sauce and I got whole grain spaghetti with olive oil and garlic.  Linda said the sauce lacked flavor.  My dish was “off menu” and was unimpressive.  Our salads, dressed with vinegar and oil, were OK and the bread was very tasty.  Linda had a glass of wine and I had blackberry sangria.  Sangria is Spanish, not Italian, but it was good.  The meal overall was disappointing but we had a great time chatting with Bruce and Linda over dinner.  The manager stopped by to ask how our meal was (as a courtesy) and ended up having to talk to us for 20 minutes.

Back home Linda made vegan banana nut muffins.  The organic bananas we bought at Meijer’s two days ago must have been bruised because they were going bad very quickly.  Banana bread or muffins was a great way to salvage what we could.  While she made the muffins I went to my office, checked e-mail, and off-loaded the photos we took today.

At 8 PM I turned on the Yaesu FTM-400 ham radio and participated in the SLAARC Info Net.  When the net was over I came back upstairs, reviewed the items in my B&H Photo shopping cart, and placed the order.  I then spent a little time researching DC distribution panels on the DX Engineering website and doing a Google search for cantilevered table supports and legs.  We each had a muffin for dessert and went to bed at 10 PM.  I put on the Detroit PBS Create channel, turned down the volume, and worked on this post for a while before finally going to sleep.

 

2015/10/15 (R) Camera Software Updates

Leave a reply

We had breakfast and coffee as usual but Linda had to leave at 9 AM for a 10 o’clock meeting at the bakery.  I had the fireplace on and hot coffee in my cup so I just stayed put in the living room in my warm winter robe.  I was finishing yesterday’s post when I got a call from Joe Cannarozzi looking for Chuck Spera’s phone number.  My N/A/P book is in my phone so after we were done talking I looked it up and texted it back to him.

After wrapping up yesterday’s blog post and starting today’s I spent a little time with the manual for the new Sony a99v DSLT camera and added a BC-VM10 battery charger to my B&H Photo cart.  Around 10:15 AM I made a follow up phone call to John Palmer at Palmer Energy Systems regarding the terminal block for the Magnum Energy Battery Monitor Kit (BMK).  John had not had a chance to talk to anyone from Magnum and indicated that his main contacts were away at a trade show.  He will still try to follow up with them but thought I might do just as well calling them directly.  They are in Washington State but are relocating to Minnesota as a result of being purchased by Sensata Technologies so I deferred the call until later today.  John said their phone and e-mail contact information had not changed yet, but he thought it might eventually as a result of the sale to Sensata and relocation to Minnesota.

There wasn’t much I could do with the desk in the bus without Linda’s help so I gathered up the laundry and started a load.  I then worked in my office for a while.  I was going to off-load photos from both the Sony a100 and Sony a99v but the Play Memories Home software indicated that updates were available and certain features (social media website interaction) required the newest version.  While I do not plan to interact with social media very much, photographically, I might want to at some point.  Besides, I like to have my software as up-to-date as possible.

The version that came on the CD-ROM was 1.03.something and the latest version from Sony’s website was 5.03.something, so my camera body was probably sitting at B&H Photo for quite a while.  The installer was a 15.6 MB download and program was a lot bigger than that.  It took over an hour to download, install, and then re-scan all of the images in the PICTURE folder, even though it just did this on Tuesday.  While I was waiting I got a solicitation from the Michigan VFW and agreed to send them a small donation of $10.

Rather than sit and stare at my computer screen I got the mail and then called Magnum Energy and asked for technical support.  I was caller number six in line to talk to someone so I selected the return call option from their menu and left my name.  Their system had already captured my phone number but had me confirm it.

One of the things I need to do with the new Sony a99v camera is figure out whether my old flash equipment can be used with it.  I found my Sunpak ring flash, my Metz CT-45, and my two Quantum Turbo gel cell battery packs.  The battery packs had their chargers connected so I set them up in the ham shack and plugged them in.

Linda called at 3 PM to let me know she was just leaving the bakery and planned to stop at Meijer’s.  That meant we would not be finishing the desk installation until tomorrow.  At that point I had not yet heard back from Magnum Energy; so much for being number six in line for a call back.

Debris piled where the new driveway extension will go. Phil’s truck and large excavator in the distance on the road at the discharge end of the culvert.

Debris piled where the new driveway extension will go. Phil’s truck and large excavator in the distance on the road at the discharge end of the culvert.

I was just about to return to my office when Phil Jarrell showed up at 3:10 PM.  I put on my outdoor work shoes and sweatshirt and went out to join him.  We looked at the discharge end of the culvert and agreed on a game plan.  He unloaded his excavator with the 30″ toothed bucket attached, drove it back into the woods well beyond the end of the metal culvert, turned it around, and brought it back towards the culvert.  Phil’s Caterpillar excavator is a powerful machine and he was able to dig the large root loose that was blocking the outlet of the culvert.  He then dug a trench back from there for about 20 feet, clearing out lots of other stuff as he went, and then stopped.

Linda got home at 4 PM after deciding not to stop at Meijer’s after all.  I walked back to the house and suggested she come see what Phil was doing.  She did and then went back inside to do some bakery-related work at her computer.

A closer view of Phil’s truck and excavator. He can move a lot of dirt, rock, and anything else he wants with this thing.

A closer view of Phil’s truck and excavator. He can move a lot of dirt, rock, and anything else he wants with this thing.

Phil used a shovel to clean out the end of the culvert, which was already filled with mud, so he could determine the elevation of the top and bottom of the discharge end of the culvert.  He then set up his laser level and started taking readings.  The 12″ diameter culvert drops 9 inches from the high end to the low end.  Phil said a 2″ drop would have been sufficient and the 9″ drop is actually a problem.  If it only dropped two inches most of the discharge end would be above grade.  But that is not the situation so we started working our way into the woods checking the elevation as we went.

The excavator positioned in the woods digging the large root out from in front of the discharge end of the culvert under the road.

The excavator positioned in the woods digging the large root out from in front of the discharge end of the culvert under the road.

By sighting down the center of the road in front of our house I determined roughly where the property line was.  Phil determined that if we continued trenching straight out from the culvert to the property line we would be out a total distance of about 50 feet and would be seven inches below the bottom of the inlet side of the culvert.  He also pointed out the soil he had already dug was very sandy and should drain well.  The fact that this whole wooded area had grass growing in it provided further evidence that it drained well.  A high clay soil would have held water and created an inhospitable environment for grass.

It was well past 5 PM and with the cloudy skies the light was fading so Phil did not want to go any farther today.  He also needed to get fuel in his front loader so it was ready to go first thing tomorrow.  He parked the excavator where it was out of the way and locked it before taking off.

 

 

The discharge end of the culvert with tree roots, dirt, and other debris cleared out of the way.

The discharge end of the culvert (dark hole center right) with tree roots, dirt, and other debris cleared out of the way.  The light gray horizonal stripe at the top of the screen is the road.

Linda made a wonderful pasta dish for dinner.  She used a whole wheat linguini and added it to a sauté of EVOO, garlic, onions, mushrooms, sun-dried tomatoes, greens, and Brussels sprouts.  Yup, Brussels sprouts in pasta.  It was a first for me and it was very good.  Earlier in the week she had picked up a couple of bottles of Barefoot Moscato at the store, one white and the other red, so I opened the red.  It was sweet, of course, but we both liked it and thought it went well with the pasta which was all savory ingredients.

After dinner I returned to my office and finally connected the new Sony SLT-A99V camera to my computer and transferred images to my laptop as I had set out to do this morning.  After completing the transfer I formatted both cards, changed the file system to create daily date folders, and set the USB transfer mode to Mass Storage.  I registered the body, vertical grip, batteries, battery charger, and SD memory cards along with the old Sony alpha 100 body and lens (DSLR-A100K) and then created entries in our password program with all of the relevant details.

The packaging for the SD cards indicated that there were two free software programs available to support the cards so I went to the referenced website.  One program was Memory Card Data Recovery and the other was X-Pict Story.  The purpose of the data recovery program is self-evident.  X-Pict Story is used to create slide shows.

Both programs required proof that I had qualifying media in the form of model and serial numbers in order to even download them.  I got the packaging for one of the SDXC UHS-1 memory cards and looked it over very carefully but could find either piece of information.  I took the cards out of the camera but could not see any identifying information on them.  I got my magnifying lens hood and with that extreme magnification I was able to just make out a model number (SF-64UY) on one side and 8-digit serial number on the other.

As long as I was in front of my computer I checked into RVillage and went through a dozen and a half notifications and “liked” or commented on a few.  There was an Ambassadors virtual meeting today 2 PM PDT (5 PM EDT but we were busy.  There is another one on Saturday at 10 AM PDT (1 PM EDT) and we will try to arrange our day so we can participate.

I spent some more time researching harness systems for holding cameras in front of me.  I think the 2-camera harness from Cotton Carriers may be just what I am looking for.  I was having trouble navigating their website using my iPad2 so I will look at their products more closely on the computer tomorrow.  I will also investigate whether I can order their products through Amazon or be better off ordering directly from the company.

Linda stayed up reading past 11:30 PM which is unusual for her.  I finished this post just after midnight but will look it over again in the morning before e-mailing it to myself.  Lights out; big day tomorrow with lots to try and get done.

 

2015/10/11 (N) Now Heat This

Leave a reply

I guess we were tired after having Madeline at our house for 23 hours.  We slept in until after 8 AM and it was going on 9 by the time the coffee was brewed and we sat down to breakfast.  I really needed to attend to some paperwork for our FMCA Freethinkers chapter but was also eager to get deeper into the manual for the new Sony a99v camera.  I installed the PDF manual onto my laptop yesterday from the CD-ROM that came with the camera and then e-mailed it go my iPad2 so I could read it conveniently.

HL – Jasper, our mackerel tabby male cat, allows himself to be photographed on the living room floor. You wouldn’t know it from this photo, but he is actually a very sweet animal ad a real joy to have in our household.

Jasper, our mackerel tabby male cat, allows himself to be photographed on the living room floor. You wouldn’t know it from this photo, but he is actually a very sweet animal ad a real joy to have in our household.

Other than the time, date, and date format I have not adjusted any of the default settings or experimented with the camera’s many functions.  I have taken a few photos just to make sure it works but I do not want to start generating a lot of image files until I have made decisions about basic things like folder naming conventions and “normal” shooting modes and settings.  I did, however, enable a “rule of thirds” grid on the viewfinder screen.

Linda worked on our personal accounting and then prepared the treasurer’s report for our amateur radio club meeting this evening.  I took a break from reading the camera manual to research the availability of some accessories on the B&H Photo website.

The electric cable release for my old Minolta 9000 SLR film cameras works with the a100 so it may work with the a99v too.  If not, newer remotes are available, including wireless ones that are not too expensive.  I found the angle finder but it is discontinued.  With the adjustable LCD screen in the back of the camera the angle finder isn’t really necessary but would have been a nice accessory just the same.  I am also looking for a case and/or a photographer’s vest and/or a chest harness/holder.  The a99v with the vertical grip and a telephoto lens is a substantial piece of equipment, both in size and weight, and the chest harness/holder would support that weight more comfortably and securely than a neck strap.  I found several interesting things but not exactly what I had in mind.

By the time Linda finished her accounting tasks I was dressed to work.  First up was the hydronic heating system in our bus.  I got four pieces of 2×4, each about four feet long, and two pieces of 2×12 about 16″ long.  I put a pair of 2x4s under each desk base and inserted one of the 2x12s between the 2x4s and the base.  That raised each base three inches which was enough to ensure that the heater hoses attached to the lower fitting on each heat exchanger sloped slightly downward back towards the main unit.

The hose that connects the two heat exchangers together in series is attached to the top fitting on each one.  Half way between the exchangers is a T with the bull branch pointing up.  A ball valve with a waste port is attached to the branch.  While Linda held the valve higher than anything else in the system I opened the valve and used a small funnel to slowly pour in antifreeze.  When the lines and exchangers appeared to be full I closed the valve, turned on the thermostat for that loop, and turned it up to cause the circulating pump to come on.  I let the pump run for a few minutes and then turned it off.  Again with Linda elevating the valve I opened it and added a little more antifreeze.  I ran the pump again for a few minutes and shut it off.  This time the coolant was still right at the valve so I shut it and Linda set it down.

It was now time for “the big test.”  In order to be able to see if there were any leaks, and catch any coolant if there were, we put heavy duty paper shop towels under all six of the clamped connections where the heater hose went over 3/4″ copper as well as under the soldered joints of the T and valve.  I opened the water bay on the passenger side, where the Aqua-Hot is installed, checked the coolant level in the expansion tank, and made sure the paper cup was positioned under the overflow tube.  The level of coolant in the expansion tank was just above Minimum Cold.  With everything in order I turned on the Aqua-Hot burner and then turned the front zone thermostat back on.  I also turned on the thermostats for the bathroom and bedroom zones to cause coolant to circulate through those loops.

There are quite a few gallons of antifreeze in the hydronic heating system and even on a mild day such as today (temperature just above 70 degrees F) it takes a while to heat it up to the 170 degrees required to shut off the diesel burner.  I kept checking the hoses by the fill valve and the expansion tank.  When the hoses were warm and the level of the coolant had risen 1/2″ in the expansion tank I cracked open the waste port on the fill valve.  I got a tiny, short hiss and then coolant came out so I quickly closed it.  It appeared that our method for filling the system and bleeding the air out had worked as intended, and there was no evidence of any leaks.

I left the Aqua-Hot on until it shut off on its own.  The expansion tank was near full at this point and I topped it up.  As the system cools down the coolant will contract in volume and some of the coolant in the expansion tank will be drawn back into the main chamber.  It’s important that there is more coolant in the expansion tank than the amount that will be drawn in or air will get drawn in instead.  I buttoned up the coach and turned to my next task.

I removed the chain from the new Poulan Pro 18” chain saw since I completely dulled it trying to cut through a tree root.  As long as the cover, chain, and bar were off I cleaned up the motor unit as best I could.  Oil impregnated sawdust is tenacious stuff.  I put the new chain on the bar and attached them to the motor, making sure the chain was oriented correctly.  I topped up the bar and chain oil reservoir and topped off the fuel tank.

It took several trips to get the 7′ step ladder, pole saw, compound lopping shears, hand tree saw, and chain saw back to the apple tree.  I noticed yesterday that one of the main branches coming off the trunk about 3′ above the ground was dead.  The bark was missing and the smaller limbs were brittle.  The bark looked like it might have been chewed away by deer but I wasn’t sure.  All I knew is that it was dead.

I started with the pole saw and worked from the ladder to cut off the limbs that extended far up into the tree.  Once I had those detached and pulled out of the tree I started the chainsaw and used it to cut off the larger branches as I worked my way down towards the main trunk.  I gathered all of the smaller material into a pile and then gathered the larger pieces together.  I used the largest piece as a sawbuck to support the other pieces as I de-limbed them and cut them into four foot lengths.  I then cut up a large pine tree limb that has been sitting on the ground under the apple tree for quite a while.  I used the pole saw and loppers to trim off a few other small branches and the carried all of the tools back to the garage.  It was 3 PM by the time I got everything put away.  I was done with physical work for the day so I got a much needed shower and got dressed appropriately for our meeting later.

The apple tree is still in need of serious pruning if it us to survive and bear useful fruit.  It particular it needs to be “topped.”  It is too tall overall, especially in the center, and much of the fruit is growing up there where the sunlight is good but it cannot be reached either by us or by the deer.  We have been putting deadwood in the firepit all summer and, more recently, on the disposal pile, where it goes mostly depending on what part of the yard the tree was in when it fell or got cut down.  In the case of the apple tree it occurred to me that Applewood is prized for the smoke it produces when grilling so I may stack it up, let it continue to dry, and perhaps rent a chipper next year to turn it into something useful.

We had breakfast later than usual, and skipped lunch, so we ate dinner at 4:30 PM, which was earlier than usual.  Dinner was lentil loaf, baked potato, and steamed broccoli, a simple but healthy and tasty meal.

On Friday I exchanged a few text messages with Josh at Coach Supply Direct regarding our desktop and table.  The net result was that his schedule had changed and he was not going to be able to get our desktop and table from Countertops Plus in Shipshewana, Indiana and deliver them to us for over a week, at the earliest.  He had also planned to bring some extra clips for our MCD shades and look at the wiring on the front passenger seat 6-way power base.  Those last two items were not critical but we are ready to install the desk once we have the desktop and cannot afford to wait another week and a half to get it.  I called and left a message for Ferman Miller to let him know I would be driving down tomorrow morning to pick them up.  I then worked on this post until 5:30 PM when I stopped to reinstall the antenna, radio, and GPS in my car.

We left at 5:45 PM for our monthly SLAARC meeting and shortly thereafter heard Mike (W8XH) on the South Lyon 2m repeater.  I replied to his call and we had a QSO that lasted almost all the way to our meeting site, where we arrived within a minute of one another.

We socialized with fellow club members from 6:30 PM until Harvey (AC8NO) called the business meeting to order just after 7 PM.  The club secretary was absent so I took the minutes.  The business meeting lasted less than 10 minutes and was followed by a presentation on APRS by Eric (K8ERS).  I gave Mike (W8XH) a check for the Icom IC-2820H dual band radio that has been in my car since early summer.

As I said at the beginning, I really needed to update the FMCA Freethinkers roster and financial reports and make them available this evening.  Well, sometimes things don’t happen just because they need too.  Today was just too perfect a day to waste it sitting inside at a computer and by the time we got home from our meeting I did not feel like starting this task.  I will try to make this a priority tomorrow evening, but each day is an adventure and I have to be agile in dealing with the myriad tasks that lay before me, including ones that appear unexpectedly.

 

2015/10/10 (S) The New Camera

Leave a reply

Madeline was awake before 7 AM and coughing loose a bit of nasal/chest congestion.  A little after 7 Linda put on her robe and went to check on her.  I put my robe on too and Linda brought her to bed with us.  She lay quietly between us for a half hour, as dawn gradually illuminated the outside world, but never fell back asleep.  I needed to change position and offered to hold her on the sofa in the living room, which she accepted.  I turned on the fireplace and she climbed up in my lap and snuggled up.  Linda joined us a little while later and the three of us cuddled in the dancing light and warmth of the fire for another 20 minutes.  These are the special moments.

Madeline wanted to see the last part of the Curious George video we watched last night so Linda did video duty while I made a pot of coffee.  By the time the cartoon was done Madeline was awake enough to help make breakfast; vegan pancakes with blueberries incorporated into the batter.  Madeline helped mix all of the ingredients but Linda handled the cooking.  Madeline is only 34 months old after all, and not ready to work with sharp objects or heat.  We had hot real maple syrup and mixed berries on the side with orange juice (not from concentrate).

The whole morning was accomplished in our robes and pajamas and it felt like it was Sunday.  Madeline even got to see a half dozen very large wild turkeys in the street in front of our house.  The cats seem to know when Madeline is seated at the table and often emerge long enough to get a few kibbles and a drink of water.  Madeline got some berry stains on her pajamas so Linda got her undressed to get them out.  Madeline took that as an opportunity to enjoy the freedom of running around in her birthday suit for a few minutes.  You can get away with that when you are not yet three years old.

Everyone got dressed and then took up their stations in the living room.  Linda and Madeline played with Legos and played (with) the organ.  Ms. M and I then played “soccer,” throwing, catching, and kicking a large beach type ball and a small soccer type ball.  Madeline was still a little tired so Linda sat with her while she played an iPad game that involved taking care of a dog.

Yesterday the UPS truck delivered a package from B&H Photo in New York.  Inside was a Sony alpha 99 camera body, specifically an SLT-A99V, which included an infoLithium (Lithium ion) battery and charger, a camera strap, a hot shoe flash adapter, Getting Started instructions, a CD-ROM with software and manuals, and various pieces of paper that included warranties and special offers.  Also in the box was a vertical battery grip (VG-C99AM), five additional infoLithium batteries, a belt-mount battery holder, and two 64 GB SDXC memory cards.

Linda suggested that this was my Christmas and birthday present for the next five years, but the reality is that the old Sony alpha 100 body was an increasingly unsatisfactory camera and needed to be replaced.  I bought the a100 in 2007 or 2008 and have not spent hardly any money on photographic equipment since then.  The a99 has been around for a few years now but is still Sony’s top-of-the-line full-frame (36mm x 24mm) sensor, A-mount lens body, which means it is compatible with all of my old existing A-mount Minolta lenses.  As it turns out, I can also use A-mount lenses designed for smaller sensors, such as the lens that came with the a100.  The a99 detects the lens format and adjusts the use of the sensor accordingly.  The a100 zoom lens, however, was an inexpensive “kit” lens that turned out not to be very sharp, especially around the edges, so it is unlikely that I will ever use it with the a99.

At 24 MP (mega pixels) the a99v is not a state-of-the-art camera by comparison to the newest offerings from Canon and Nikon, or even Sony’s own E-mount product line, but it is double the pixel count of the 12 MP a100, and has many features that the a100 does not have, including much better auto-focus and much better sensitivity to low light.  The maximum effective ISO speed on the a100 is 1600 whereas the a99v is 25600 and can be set even higher if needed.  The a99v also includes a built-in GPS receiver that enables it to geotag images.  It includes a hot shoe flash adapter, as well as a PC flash connection, so I have some hope that I will be able to use my old flash equipment, something I have not been able to do with my much older Sony alpha 100.

The old a100 holds one Lithium ion battery and one Compact Flash card, 4 GB maximum.  It also has an adapter so it can use SD memory cards, but the maximum usable capacity is still 4 GB.  The a99v also holds one Lithium ion battery in the camera body but holds two additional batteries in the vertical grip accessory.  Not only will the vertical grip be handy for shooting in portrait orientation, the two additional batteries should allow for extended shooting time even when using flash.  The body also has two memory card slots both of which can accept SD memory cards up to 64 GB.  Slot one can also accept a Sony Memory Stick Pro Duo.

Digital cameras are sophisticated combinations of mechanical, optical, electronic, and computer technologies.  Compared to film cameras of yesteryear prosumer and professional cameras, both single lens reflex (SLR) and single lens translucent (SLT) like the a99v, are feature-rich devices designed to give photographers complete control of the images that are produced.  That also means they are complicated devices with significant learning curves.  Throw in the fact that cameras like the a99v can shoot HD movies with sound and it takes considerable practice over an extended period of time to really master their use.  But I am retired, and photography is one of my three hobbies, so I have, and will take, the time to learn to use this new camera competently.  Competence in this case means the ability to quickly and intuitively select modes and adjust settings to allow me to capture (create) the images I envision.

Brendan called to see how Madeline was doing and arranged to pick up her up later in the afternoon, after the 3:30 PM start time of the U of M football game.  Unless you are attending the game you do not want to drive in, or anywhere near, Ann Arbor for the four or five hours preceding the opening kickoff.  It’s not a great place to be after the game ends either, especially as regards getting in to a restaurant or pub, unless you specifically want to be part of the pre/post game experience.

Madeline wanted to go outside and swing so we put on our shoes and got her into a light jacket.  She is just learning to pump her feet.  She understands the concept but does not yet having the timing.  When she was done with the swing we collected branches and twigs that were lying in the yard and added them to the burn pile.  We then walked around part of the back yard but her shoes got wet from the grass and she wanted to go back inside.

I checked our apple tree and was surprised to see damage that looked similar to that caused by the Emerald Ash Borer.  It’s possible that deer have been chewing at the bark but whatever the cause there are some very large limbs that are now dead.  What concerned me is that I do not recall them being in that condition the last time I looked.  The tree is very old, very large, and has not been properly pruned for a very long time.  We may end up losing it in the end, which would be a shame, but the time to prune is late winter to very early spring and we have not been here at that time of year the last two seasons.  I have my eye on a portion of the western 2/3rds of our yard, however, as prime real estate for some new trees, including some fruit trees.  But not this year, and probably not next year either.

Madeline was hungry after her backyard adventure.  She had soy yogurt and pistachios for lunch and found the pistachios very much to her liking.  She and Linda watched a Daniel Stripped Tiger cartoon and then she laid down for a nap at 1:30 PM.  I snuck off to my office to check e-mail, install the software that came with my new camera, and start downloading updates for the Linux box.  Completing the installation of the Sony Play Memories Home software required the camera to be connected to the computer, so I installed the two SDXC memory cards and one of the fully charged batteries.  On first power up I had to set the date and time.  I then connected it to the computer with the provided USB cable and completed the software installation.

One of the things the PMH software does is go through the PICTURES folder and catalog all of the images it finds by date and makes them accessible through a calendar view.  The camera also came with the Image Data Converter program for dealing with RAW format image files and Remote Control software that allows the camera to be tethered to a computer and controlled from there.  I will eventually have to figure out if/how Adobe Lightroom and Photoshop deal with Sony RAW files.

I quit working at 3 PM, Linda got Madeline up at 3:30, and Brendan arrived at 3:35.  Madeline had been sleeping pretty soundly and did not wake up easily.  She was initially upset that her mom did not come with her dad to get her and got herself worked up enough that she took quite a while to settle down.  To make matters worse she really wanted to stay another night at our house and was resisting going home even though she wanted to see her mommy.  When you are not yet 3 years of age it’s hard to understand that you cannot have mutually contradictory things at the same time, although I suppose in this case that had Shawna come to the house and stayed overnight Madeline could have had everything she wanted.

Linda got Madeline’s toddler bed deflated and packed for travel and rolled up her sleeping bag.  She and Brendan then gathered up all of the things that had to go back to Ann Arbor.  Madeline does not travel light; the clothes, books, toys, stuffed animals, and other accoutrements filled four carry bags in addition to the bed and sleeping bag.

After Brendan and Madeline left I checked my e-mail and replied to several having to do with my duties as secretary of the FMCA Freethinkers Associate Chapter.  We will be holding our annual meeting by teleconference in the next three to six weeks and I have to update the roster and prepare financial statements.

I transferred the complete User’s Manual for the Sony a99v from the CD-ROM to my laptop, backed it up to the NAS units, and then e-mailed it to my iPad.  I downloaded it to my iPad and spent much of the evening reading it.  We headed off to bed a little after 9 PM.  I tuned into the Create channel on Detroit PBS (WTVS) and watched a series of back-to-back episodes of Cooking with Nick Stellino while I worked on this post.  Nick’s show is charming and he is the poster boy for unapologetic high self-esteem but with no hint of arrogance.  His love of food and passion for cooking is infectious and I enjoy his show.

 

2015/10/09 (F) All Charged Up

Leave a reply

We finished the current batch of granola for breakfast and had just finished our meal when Chris, from Bratcher Electric, showed up at 8:45 AM to service the whole house generator.  He let me watch and explained the various steps in the process.  The trickiest part appeared to be replacing the spark plug on the back side of the engine.  Everything else was fairly accessible.  There is a 1/4 turn valve to drain the oil and a rubber tube to get it out to a collection vessel.

Chris had what looked like a small gas can but it was painted blue.  It had a clear plastic tube attached to what would normally be the air vent.  The tube was sized to just fit inside the oil drain hose.  A vacuum pump was threaded on to opening where the pour spout would normally go.  A few pumps of the handle and the device sucked the oil right out of the engine and contained it so he could transport it easily and cleanly.  It was a very clever device, and obviously very handy for someone who does several generator maintenance procedures every day.

He gapped the spark plugs at 0.028″, checked the air filter (it was fine), replaced the oil filter, noting the date on the filter with a permanent marker, and put ~2-1/3 quarts of 5W-30 synthetic oil back in the engine.  He cautioned me to only use the specified filter and pure synthetic oil.  The engine runs hot under load and regular oil can lead to problems.  He checked all of the settings and changed the weekly self-test to run at full speed for the entire time.  He prefers that setting as it gets the engine up to normal operating temperature and helps burn off any moisture in the oil.  He started the unit manually, let it run for a while, and then shut it down and put in back in AUTO mode.

Linda prepared the dry ingredients for her vegan chocolate cupcakes and then put together a grocery list.  She left to go to Meijer’s while Chris was still working.  He finished up around 10:15.  I worked on the bus, using split plastic wire loom to protect the wires that power the fans on the heat exchangers.  I then worked on reconnecting the wires from the front bay electric heater to the supply wires.

A close up view of the fill/bleeder valve assembly for the heat exchangers in the desk bases.

A close up view of the fill/bleeder valve assembly for the heat exchangers in the desk bases.

The supply wires run inside the HVAC duct.  They originally came out of the duct and went through a hole in the floor into the OTR air-conditioning bay and then through the partition wall into the front bay.  I had to cut the cable and pull it through the floor from underneath so I could install the new floor tile.  I could clearly see where the OTR HVAC supply duct came into the distribution duct but when I tried drilling from below I seemed to hit metal.   The bottom of the duct was clearly plywood so I drilled from above with a 1/2″ spade bit.  I got through most of the plywood but again seem to hit metal.  I knew there wasn’t anything in that location, like wires, pipes, or air lines, so I switched to a 1/2″ twist drill and finished the hole.

I dropped a screwdriver through the hole so I could locate it from below.  I then pushed the electrical cable from the heater up through the hole and secured it to a fastener on the forward wall with a cable tie.  Linda got back at this point so I helped get the groceries into the house.  She then mixed a new batch if granola and put it in the oven to bake.  I gathered up my electrical tools, uncapped the feed wires, checked them with a volt meter to make sure they were not energized, connected the feed wires to the load wires, and tucked them back inside the duct.

We had a choice as to what to work on next—fill the heat exchangers and hoses with antifreeze or hang the wallpaper in the hallway—so we had lunch.  Summer has passed, but tofu hotdogs with mustard, onion, and relish, along with some red grapes, was still a tasty lunch.

When we got back to work in the coach we decided to hang the wallpaper.  The pieces were already cut and laid out on the bed.  Hanging them not only got them off the bed, it would allow us to get the wood trim off the bed as well and back on the lower wall.  But not today.  The wallpaper adhesive needs to cure for 24 hours before we work around it and does not achieve its full cure for 5 to 7 days.  We have one piece of wallpaper to hang behind the forward end of the sofa but the wall prep is not finished in that area.  Once that piece is up, and we have the Corian top for the desk, we can complete the installation of the desk and sofa.

Shawna was bringing Madeline at 4:30 PM to spend the night with us.  It was already 2:30 and I needed to get cleaned up and put on non-work clothes before they arrived so we called it a day.  I had once again accumulated quite a few tools in the bus.  I gathered up all of the ones I was done with, returned them to the garage, and locked up the coach.  The UPS truck showed up with my package from B&H Photo which I set aside temporarily while I took a shower and got dressed.

The box looked like it had been treated well in shipment.  I opened the box, carefully removed all of the contents, and compared them to the order/packing list.  Everything was there and appeared to be in pristine condition.  I unwrapped the battery charger and Lithium ion battery, put the battery in the charger, and plugged it in.  The new charger is essentially the same as the one that came with my Sony alpha 100 years ago so I got the old one from the basement.  I bought five additional batteries so I opened one of them and plugged it in to the old charger.  I then found the Instruction Manual and curled up with it on the living room sofa while Juniper (the cat) curled up on me.

The directions with the charger and the batteries indicated that it can take up to 175 minutes to fully recharge a battery and that full charge is not obtained until an hour after the charging light goes out.  So, basically, I need to leave the batteries in the charger for three hours to ensure they are fully charged.  The camera takes one battery, and the vertical grip accessory takes two batteries, so my normal operating configuration will be to have three batteries in the use.  That’s why I have a total of six batteries for this new camera.  I will probably buy another charger so I can charge three batteries simultaneously.

I called Chuck to let him know I got my car back late yesterday but would not be able to move the windshields box until sometime next week.  It turned out that he and Barbara were also busy all weekend.  His daughter, son-in-law, and grandson were in town with more family arriving from Trinidad and Tobago this evening.  Tomorrow is his grandson’s first birthday and Sunday he is being baptized at the church in Ann Arbor where Chuck’s daughter was married.

Shawna showed up just after 4:30 PM.  Madeline had fallen asleep in the car and was slow to wake up, clinging to her mom for quite a while.  Linda brought in the various bags of clothes and toys along with the inflatable bed and got everything situated in the middle bedroom.  When Linda mentioned making cupcakes Madeline finally woke up and became cheerful.  Once her focus was on baking with Grandma Linda Shawna was able to slip away without any drama on Ms. M’s part.

Today was Brendan and Shawna’s friend Jorge’s birthday and the three of them were headed to a new restaurant in Detroit to celebrate.  The restaurant does not take reservations and is apparently very popular at the moment so Shawna was not sure if they would actually get to eat there.

With Linda’s help Madeline mixed the ingredients for the cupcakes and managed to pour most of the batter into the baking tray.  Linda then prepared dinner while I played with Madeline.  We did the ABCs on her placemat, and then colored with crayons.  Dinner was mock chicken tenders, edamame, and steamed carrot rounds with fresh orange segments and sliced strawberries, so it was mostly fresh, whole plant-based foods.

As soon as the cupcakes were cool enough to be frosted Madeline coated each one with the special Halloween orange frosting and the back and orange Halloween sprinkles.  I was summoned to inspect the work and then it was time to eat.  Madeline selected a cupcake for herself and then one for me and one for Linda.  We ate them at the table and they were very good.

After cupcakes we played soccer with two different balls, kicking and throwing them all around the house.  By 8 PM we needed to start winding things down.  Shawna had left her iPad and Madeline selected a Curious George video about Christmas.  Linda and Madeline climbed up in our bed where they could stretch out their legs and watched the first 60% of the cartoon.  I opened two more camera batteries and put them in the chargers and then joined the girls.  We will watch the rest of the cartoon tomorrow morning.

I helped Madeline brush her teeth and Linda got her into her pajamas.  Linda read her several stories and finally got her in bed around 9:15 PM.  During dinner Madeline inquired about having pancakes for breakfast.  (I had made the same inquiry over lunch.)  Linda did not have all of the ingredients she needed so after Madeline went to bed I went to Meijer’s in Howell and bought avocado oil and all-purpose flour.  Linda is trying to use up ingredients rather than stock up on them so I bought a two pound bag of King Arthur organic unbleached enriched all-purpose flour even though I could have bought a 10 pound bag of the Meijer’s brand (bleached and not organic) for only 50 cents more.

Just before going to bed I opened two more batteries and put them in the chargers.  We went to bed at 11 PM but did not turn on the TV to ensure that we did not disturb Madeline’s sleep.  I was basically done with the draft of this post and read some more of the Instruction Manual for my new Sony alpha 99 (SLT-A99V) camera and vertical battery grip (VG-C99AM).  I am really looking forward to using this new equipment but it takes a couple of days to charge batteries, install software, and read manuals enough to be able to configure it for first use.  This class of camera has a lot of adjustable parameters with default settings that may or may not be what any particular user wants.

 

2015/10/08 (R) A Mighty Hose

Leave a reply

Linda was up before 6 AM to drive to the bakery ahead of the worst of the morning rush hour traffic.  I was aware of her getting up but fell back asleep.  She is very quiet as she goes about her preparations on such mornings, which I appreciate.

I got up around 8AM, fed the cats, and cleaned their litter tray.  I made half as much coffee as usual and measured out a bowl of granola, probably a little more than usual.  I took my coffee to the living room and turned on the fireplace, expecting to settle in with my cats and work on my iPad, but the iOS 9.0.2 update was available so I started the installation and read the last few pages of Number Theory and Its History by Oystein Ore.  I read from screens more than from paper these days, but I still like to curl up with a printed book.

Jasper used to sit next to me on the sofa in the morning but seems to prefer sleeping on top of one of the back cushions these days.  Juniper, who never used to pay much attention to me, has taken his place.  She has always sought out warm places to curl up but has always preferred Linda’s lap to mine.

My bus project for today was reassembling the plumbing to the two fan-coil heat exchangers that go in the bases under the two desk pedestals.  Yesterday I cut new holes for the supply and return hoses.  My first task was to remove the hoses from the bleeder valves and install barbed plastic plugs in the ends to prevent coolant from coming out.  I then pulled the hoses back and out through the new openings.

The area behind the desk where the heater hoses emerge from the passenger side OTR HVAC duct.

The area behind the desk where the heater hoses emerge from the passenger side OTR HVAC duct.

I worked on the hose for the right hand (rear most) heat exchanger first.  I positioned the base, routed the hose to the lower fitting, and marked where to cut it.  I put a plastic paint tray liner under the hose before I cut it but more coolant came out than I expected.  I got as much of it in the liner as I could and grabbed a bunch of paper shop towels.  I got the liner outside without spilling any antifreeze and poured the used antifreeze in a one gallon jug that I keep for just this purpose.  I used a funnel that is also reserved for use with antifreeze.

I took the cut off piece of heater hose outside, plugged end down, and set the open end in the tray liner.  We already had a bucket of soapy water in the bus as we had planned on hanging wallpaper yesterday.  I wrung out the sponge and then squeezed some of the soapy water on the floor and cleaned it up with paper shop towels.

The left and right desk bases and center cover/spacer set in place. The heater hoses are not yet connected.

The left and right desk bases and center cover/spacer set in place. The heater hoses are not yet connected.

With the mess cleaned up I slipped two hose clamps over the end of the hose and worked it onto the lower fitting on the heat exchanger.  If only it had been as easy to do as that description!  The 3/4″ i.d. rubber heater hose did not just “slip” over the 3/4″ o.d. copper pipe even with some residual antifreeze lubricating the inside of the hose and the outside of the pipe.  Indeed, it took considerable and simultaneous pushing and twisting to get the hose on.  It was also a lot harder than I expected to work with the heat exchangers installed in the bases, even without the desk pedestals in place.

I was interrupting my work as needed to take photographs and as I finished up the first hose the camera refused to trigger the shutter.  The LCD screen indicated that the compact flash memory card was full so I went to my office to offload the images from the last few days.  My other CF card was empty so I put that in the camera and set it aside.  I had not backed up my photos to the Network Attached Storage units in quite a while so I decided to take the time to do that.  While I was at it I backed up my blog posts from December of 2014 through July of this year along with several issues of The Gypsy Journal.

As long as I was at my computer I checked my e-mail accounts, logged into RVillage, and logged into my account at B&H Photo.  My new Sony alpha 99 and accessories were on their way from New York and due to be delivered by the end of the day tomorrow.  I am excited to finally be getting a new digital camera with a full frame (35mm) sensor that will work correctly with all of my old Minolta A-mount lenses.

By this point it was lunchtime so I cleaned up (antifreeze is definitely NOT good eats) and scrounged around the kitchen for something tasty but easy to fix.  My “go to” meal is usually roasted red pepper hummus and sourdough pretzel nibblers.  We had a little hummus left, which I finished, but I was still hungry so I made a bowl of popcorn.  I would probably not make a good bachelor.

I went back to the coach and contemplated attaching the other hose to the left heat exchanger.  While I was thinking about it Linda called to let me know she was on her way home.  It was 1 PM so I decided to wait for her to get home to help me install the second hose.  I had some phone calls to make and used the time for that.

I called Karen at Bratcher Electric to schedule the upgrading of our 60 Amp sub-panel in the garage to a 100 Amp main panel.  While I had her on the phone I asked if Mike would itemize the quote.  I also mentioned that they had picked up two or three whole house generator customers through my referrals and perhaps Mike could provide some consideration for that in the pricing.  Next I called Ferman Miller at Countertop Plus in Shipshewana, Indiana to check on the Corian desk top and table.  Ferman answered the phone and said he had called Josh this morning to let him know the pieces were ready for pickup.  I then called Josh to see what his plans were.

We originally agreed that he would pick them up and bring them to our house on his way to visit relatives in the northeast side of the Detroit metropolitan area.  His plans had changed and he won’t be visiting his relatives anytime soon.  He is leaving on Tuesday for a FMCA area rally in the Carolinas and will be gone for a week.  Before he leaves he needs to get something to a customer in Cleveland in addition to getting our stuff to us or deciding that we will have to drive to Shipshewana to get it ourselves.  One option is that we meet him somewhere on Sunday.  Ann Arbor is a possibility but Toledo or Defiance (Ohio) are more likely rendezvous points.

Linda got home around 2 PM and changed into her work clothes.  With Linda’s help I was able to avoid the mess I had with the first hose.  The second hose was even harder to get on than the first one but we managed to do it.  In part because of the arthritis in the joints at the base of my thumbs I do not have as much grip strength as I would like and often need.  The twisting and pushing was hard on my hands and the confines of the base and proximity of crisp wooden edges resulted in lots of small cuts.  This was not something I anticipated in the design and construction of the bases and the installation of the heat exchangers.

I took a break and drove to Northwest Plumbing Supply to see if they had a bleeder valve like the ones in our bus system.  They did not and had never do seen anything like it before.  The showed me a couple of things they did have but I did not buy anything.  I got a call from Brighton Honda that my car was ready for pickup so I headed home to get Linda.  She drove me to the dealership and then went on to Meijer’s for a few grocery items.

I drove to Lowe’s in Howell and was fortunate to find Lars in the plumbing department.  The store was not very busy and he took an interest in showing me various plumbing options that might allow me to replace the bleeder valve with something that would do the same thing while also giving me a way to add antifreeze to the system.  What I ended up with was 3/4″x3/4″X1/2″ copper sweat T and a 1/2″ sweat ball valve with a waste port.

Bruce works on attaching the heater hoses to the fill/bleeder valve T assembly he built.

Bruce works on attaching the heater hoses to the fill/bleeder valve T assembly he built.  (Photo by Linda.)

Back home I cleaned some 3/4″ and 1/2″ copper pipe with 120 grit plumbers sandpaper.  I cut two pieces of the 3/4″ pipe about 3″ long and one piece of the 1/2″ pipe about 1-1/2″ long.  I brushed the inside of all the fittings and test fit the pieces.  I then applied flux to all of the surfaces to be soldered, inserted the two 3/4″ stubs into the run fittings, inserted the 1/2″ stud into the bull fitting, and put the ball valve on the other end of the 1/2″ pipe.  I used the lever on the ball valve to mount the assembly in my bench vise.  I removed the waste port cap to protect the neoprene seal and opened the ball valve so as not to trap heat inside.  I then heated the T and the end of the valve and applied the solder.

I figured there had to be an easier way to get heater hose onto the heat exchanger and that Butch was the guy who would know what it was.  I called and he said antifreeze can obviously be used and works fairly well but that a small amount of dish soap would also work as a lubricant and not harm the antifreeze or the Aqua-Hot and its components.  As long as we were on the phone I caught up on their activities.

They were still there at the RV Park in Bouse, Arizona but only until the 15th of this month.  The terms and conditions of their employment as managers of the park had not turned out to be as described during the interview process and they are wrapping up after only a month on the job.  They will move their bus back to Quartzsite and spend at least part of the winter at Joe and Connie’s place where we both spent last winter.  I know it was a big disappointment to them that the situation in Bouse did not work out, but their situation in Q will be familiar, comfortable, and inexpensive, as well as convenient to the Quartzsite Gem and Mineral Club which they joined this past winter.

For dinner Linda made a blend of onions, garlic, mushrooms, and power greens and served it over a baked potato topped with Daiya cheese.  It was very yummy, and the potatoes kept the dish warm all the way to the end.  The weather had turned cloudy through the afternoon and we got the first raindrops during dinner.

The fill/bleeder valve T assembly with the heater hoses connected. The assembly is located between the bases at the floor and will be hidden by the center connector/cover.

The fill/bleeder valve T assembly with the heater hoses connected. The assembly is located between the bases at the floor and will be hidden by the center connector/cover.

I had really hoped to have the hydronic heating system reassembled today so we went back out to bus after dinner to hook up the heater hose that runs between the two heat exchangers.  This was actually two pieces of hose with my homemade bleeder/fill valve half way between the two exchangers.  Even with dish soap the two hoses were very difficult to get onto the heat exchanger fittings and the bleeder/fill stubs, but I got them on.  Linda took pictures while I grunted, groaned, and moaned and I took a few more when I was done.

It was 8:45 PM when we finally quit working, secured the bus, and went inside.  I cleaned my hands as best I could but I could not get all of the black from the rubber hoses to come off.  We sat for a while in the living room and had the last of the frozen chocolate torte that Linda made a couple of weeks ago.  We finally turned in around 10 PM and watched Rick Steve’s Europe, Travel in the Americas, and a couple of cooking shows while I worked on this post.

 

2015/09/30 (W) Annual Checkups

Leave a reply

We were both scheduled for our physical exams today.  Mine was at 9:20 AM, and I needed to leave by 8:20 to be sure I was there on time, so I got up at 7:30, showered, and dressed.  I took my vitamin and allergy meds but did not make coffee or have breakfast, Linda’s appointment was at 1 PM so she slept in.  We both had our blood drawn a week ago and the lab results had already been reviewed by our doctor and made available to us via the Henry Ford Health System MyChart patient information system.

We are both basically in good health with only minor issues, such as arthritis in the base of my thumbs or worn out knee joints in Linda’s case.  Both of our blood analysis results were OK across the board but that does not mean we were completely happy with them.  My blood pressure was a little higher than I would like but the doctor thought it was fine.  Linda’s total cholesterol is higher than she would like so we are still learning what dietary choices and physical activity have to do with controlling that.  We respect our doctor’s judgement but we are also re-calibrating our own understanding of what is desirable for us versus what is “normal” for adults our age living in the USA.

The problem with “normality” is that it is a statistical concept.  In a population that is overwhelmingly unhealthy we do not necessarily want to be normal.  As an example, American medicine considers the normal range for total cholesterol to be 120 to 200 and yet research, as reported by Dr. Michael Greger at NutritionFacts.org, shows that real health is associated with a number less than 150.  Most Americans have total cholesterol way above that except for one group; active vegans.  As another example it is generally accepted that as people age blood pressures in the 130’s over 80’s are “normal” and yet in rural China and Africa, where people eat mostly whole-food plant-based diets, “normal” is 110 over 70 for their entire lives.  Heart disease and other “western” aliments are also virtually unknown.  We are still works in progress.

I do like my morning coffee even though it is usually half regular and half decaffeinated so I left my physical exam and headed for the Tim Horton’s at Beck and Grand River Avenue.  While I was in line I got a call from Chuck wanting to know if the new windshield cut down any of the wind noise.  He was headed to his shop just down the street so I suggested he stop and chat over a cup of coffee.  I told him what intersection I was at but mistakenly told him I was at Dunkin Donuts so he stopped there first.  We have air/water leaks around the other windshields, side windows, and the entrance door so I could not tell any difference from replacing just one windshield.  I trust, however, that the new one will not leak air or water and it is currently not cracked or dinged, so I am happy with it.

Linda texted me that she was leaving early for her appointment and was going to stroll around the mall.  When I got home and tried to lock the driver side door on my Honda Element the key stuck in the lock and would not turn or come out.  This lock has been failing for a while but the failure mode has been an inability to insert the key.  Fortunately I had a second key in the house and was able to unlock the passenger door and rear lift gate.  Not only was I unable to remove the key, the latch was disconnected from both the outside and inside handles and I could not get the door open.  I called Brighton Honda to make sure they could give a ride back to the house and then removed the ham radio control head and microphone, the GPS, the cellular booster, and the 2m/70cm antenna before driving to the dealership.

Rob checked me in and tried jiggling the key harder than I had.  The key still did not come out but he managed to get the latch to re-engage with the handles so we could get the door open.  He wrote up the work order and I only had to wait a short time for the shuttle to return and drive me home.  Rob called later in the afternoon with the estimate.  They had to order a new latch which should be in on Friday, and then send the latch and one of my keys to a locksmith to have the lock matched to the key.  By the time they got the mechanism back from the locksmith and installed in the door he figured it would be the middle of next week.  That was not ideal for me but it was what it was.  The car was not very usable in its current condition so I did not really have a choice.  I was all too well aware that this was another case where I put off fixing something longer than I should have.  I was lucky, in a sense, that it failed when and where it did as I was not stranded somewhere calling Linda to bring the spare key.

When I got back to the house I attached the battery charger to the battery in the lawn tractor.  Philip Jarrell is supposed to start working on our French drain and pull-through driveway extension tomorrow and the lawn tractor is parked where he will be working.  I added gasoline to the tank but even after bringing the battery to full charge and using the jump start feature on the charger I was unable to get it started.  After repeated attempts I gave up.  When Linda got home we disengaged the transmission and pushed to another part of the yard where it would be out of Phil’s way.

I have mentioned before that this lawn tractor was left here by the previous owners.  The mower deck was pretty messed up and we removed it this past spring.  We have a lawn service, Kish Lawn Care, mow the grass so we really do not have a reason to buy a new lawn tractor/mower.  Still, I thought it would be useful for hauling materials and debris around the property and I put new drive tires on it in 2013 and bought an 18 cubic foot dump trailer this year to pull around behind it.  Whatever the problem is I’m sure it can be fixed, and probably by me, if/when I have time; which I do not at the moment.

I spent much of the rest of the day in my office except for dinner.  I reviewed the final draft of an article I wrote which is running in the October 2015 issue of Bus Conversion Magazine.  I then logged in to the B&H Photo website and finally ordered the Sony alpha99 (a99v) DSLT body and a few accessories.  The body comes with the vertical grip battery pack for no extra charge, a $378 value, so that was a nice surprise.  The body comes with one battery but the grip, which holds two additional batteries, does not come with any, so I ordered five additional batteries giving me six total for two complete sets.  I also ordered two 64 GB memory cards and a small case for carrying an extra battery on my belt.  B&H is closed until October 7 for SUCCOS.  My order is scheduled to ship on the 8th and arrive on the 9th, no added shipping charge.

I spent the rest of my time editing drafts of blog posts and selecting/processing a few photos to go with some of them.  I hope to have the posts for the first two weeks of August uploaded in the next couple of days.  When I finally came upstairs we watched a show on PBS about the life long work of biologist E. O. Wilson.  It was fascinating.

 

2015/01/8-14 (R-W) Q 2015 W2

Leave a reply

2015/01/08 (R) Up On The Rooftop 

A panorama from the roof of our bus. Left edge is NE, center is S, right edge is NW.

A panorama from the roof of our bus. Left edge is NE, center is S, right edge is NW.

As forecast, we woke up to cloudy skies and milder temperatures.  The clouds to the southwest looked like they might produce rain but the winds were blowing gently from the southeast so the rain would not be for us.  This was the day we’ve been waiting for, the perfect kind of weather for washing a bus.  But not first thing in the morning.  Coffee and breakfast come first while we wait for slightly warmer temperatures.

The waste water tank level sensors are not accurate but our fresh water tank sensors are OK.  The fresh water level gauge was showing less than 1/3 tank and the grey water tank gauge was showing full so it was probably time to dump and fill.  When I checked the fresh water level visually we were at 1/6th tank.  I dumped the black water tank and then the grey water tank, both of which were fairly full, and then filled the fresh water tank.  I have the city water regulated to ~50 PSI (static) which drops to ~30 PSI when the fill valve is fully opened.  At that pressure it takes about 40 minutes to fill the tank.

I last dumped the waste tanks on December 30th and added 25 gallons of (hard) fresh water.  On December 31st I added another 30 gallons of (hard) fresh water.  On January 2nd I recharged our water softener, drained about 1/6 tank (~20 gallons) of (hard) fresh water and filled the tank with 120 gallons of soft water.  I checked the hardness of the water coming out of the softener after that fill and it was 1.5 grains/gallon (25 ppm).  I checked it again after today’s fill and it was still 1.5 gpg.  Since we are keeping a log of the dumps and fills I plan to check the hardness after each fill so can regenerate the water softener before it gets depleted and we end up with really hard water in our tank and system.

Butch happened to be at the Post Office Annex today checking the P. O. Box at exactly the same moment a postal worker was about to put something in the box and then stopped because of the forwarding tag.  The “something” was our package of water hardness test strips from Bristol, Indiana and the worker was kind enough to give it to Butch to give to us.  He also learned that they still have P. O. Boxes available so he went to the main post office to find out more about that.  He came back with a form to fill out and it had room for all of our names so the six of us are going to share the box and the cost, which is $56 for six months, or just under $20 per couple.

While the fresh water tank was filling I started getting ready to clean the roof by getting out our Little Giant step/extension ladder and various cleaning supplies.  The dump and fill was done by 11 AM and it was warm enough by then to start working.  Swim trunks, a white T-shirt, and Kean sandals was the uniform of the day.  I carried the hose sprayer up the ladder with me and then lowered it down to use as a hook and lift wash water bucket, scrub brush, and other paraphernalia up to the roof.

It turned out to be sunnier than I had hoped but I worked for about four hours, not including a lunch break, and scrubbed the entire roof.  I used McGuire’s red automotive soap and rinsed thoroughly.  I had already washed the roof once using Dawn dish soap (a big ‘no no’, apparently) and a long-handle soft brush.  That washing had removed surface dirt and revealed the full extent of the dark “spotting” that gave the entire roof a mottled appearance.  The roof looked a lot better after I scrubbed it but a lot of the spotting remained.

We are anxious to clean the sides of the bus but there is no point doing that until we are done with the roof.  We want the roof “like new” clean so dirt doesn’t run off it onto the sides, but we also want it clean because we are seriously considering having Discount Solar (here in Quartzsite) install solar panels and a charge controller and do all the wiring.  As long as we had the hose, brushes, and soap out we decided to wash the car.  It was even filthier than the bus, if that’s possible, and it was nice to finally have it clean.

After cleaning up our equipment I got cleaned up and then sat and visited with Butch for a while.  Linda came over and announced that she wanted me to take her to dinner.  Butch and Fonda decided to go too so we went to Crazy Jerry’s, which is not to be confused with Silly Al’s.  Silly Al’s is supposedly the #1 eatery in Q, at least for pizza, but they have karaoke every night starting at 7 PM.  Thank you, no.  Crazy Jerry’s also has pizza and we tried the vegetarian, hold the cheese.  Very thin crust (the way we like it) and lots of topping.  A couple of side salads and a side order of French fries.  FWIW, we did not eat the entire pizza and brought home the leftovers.

Linda split a pair of Scrabble games with her brother, the first one he has won in quite some time.  She had an e-mail reply from Mara.  She is camped about 70 miles south of Q and is headed here in the near future and is going to camp with the WINs (Wandering Individuals Network).  I checked e-mail, updated my BCM article spreadsheet with two more story ideas, played a few games, and worked on this post before turning in for the night.  We will have been here a month as of Sunday.

The Hi Jolly Daze Parade. Quartzsite, AZ

The Hi Jolly Daze Parade. Quartzsite, AZ

2015/01/09 (F) The P. O. Box

I left the ladder setup yesterday so I could check the roof again this morning and determine what additional cleaning measures, if any, I might want to take.  I also wanted to get back up on the roof and measure the space we have available for solar panels.  I was expecting two packages via UPS; one from B&H Photo (Manfrotto nodal panoramic tripod head) and one from Sure Marine Service (Webasto repair parts).  I had a nice view of the mountains surrounding Quartzsite from the roof of our bus and wanted to shoot some panoramas with the new head when it arrived.

Butch, Fonda, Jim, Barb, Linda, and I all went to the U. S. Post Office in Quartzsite this morning to sign up for our very own P. O. Box which means we finally have a way to receive USPS mail while we are here.  Just in time, too, as Q has really filled up in the past week and there is more to come.  I have an FMCA national education committee meeting on Monday and need to write a few items for a member survey and review other materials.  Gary (from BCM) is also due to arrive on Monday, and both Curtis (from RVillage) and Mara Culp (HFH build acquaintance) may be headed this way as well.  I believe Chris Dunphy and Cherie Ve Ard of Technomadia are already in the area.  The big RV tent is up and those vendors are arriving and setting up.

Once we were done at the post office I went to Discount Solar to discuss a possible installation on our coach.  The Kyocera panels are 26.5″ W x 59.0″ L.  They are “12 V panels” but are rated at 140 Watts putting out 7.9 Amps.  They cost $350 each.  Those numbers compute to an output voltage of 17.5 VDC and $2.50/W.  (If a 140 Watt panel was operating at 13.8 Volts it would produce just over 10 Amps.)  Because we have a 24V battery system we would need to install the panels in series-connected pairs.  The preferred installation for the rectangular panels is to have the long dimension lined up fore-n-aft to either side of the centerline of the roof.  Tilt mounts are available ($45/panel) but we would probably not install them due to the difficulty of getting onto our roof to use them.

“12 volt” batteries typically charge at around 13.8 to 14.1 volts.  Our “24V” system charges at 27.6 to 28.2 volts and a series-connected pair of panels produces 7.9 A at 35V (full sun) for 276.5 volt-amps, which is essentially “watts.”  Two pairs would produce 15.8 A (553 V-A), and three pairs would produce 23.7 A (829.5 V-A).  The higher voltage output of the panels is reduced and regulated by a solar charge controller before getting to the batteries.  Discount Solar carries Blue Sky and Trimetric maximum power point tracking (MPPT) controllers and the Blue Sky Solar Boost 50 would handle three series-connected pairs for about $550.  The MPPT controllers are DC-to-DC converters so they convert the excess voltage into additional current.  With full sun this six panel system could supply up to 30 A of charging current at the proper voltage, which is why we would need an MPPT controller that can handle more than 30 A of charging current.  We would also want room for expansion or replacement with higher wattage panels if they were available at some point in the future.  One of the nice things about the solar system is that it would always be on and would “play nice” with our other charging systems. Another nice feature is that they are silent when operating.  Ahhhh.

Because of the size of our house battery bank (400 A-Hr at 24 VDC) and the fact that we have a residential refrigerator, auxiliary air-compressor, and other AC loads, we would need/want at least six panels.  (I have not included the four Group 31 wet cell batteries that are used to start the engine and power the chassis as part of the solar system.)  If the batteries were discharged 50% (200A-Hr) it appears that it would take just under seven hours to bring them back to full charge based on the 30A charging current.  In actuality it would take longer in a boondocking situation as the sky is not always clear, the sun is rarely directly overhead (perpendicular to the panels), there would be devices using some of the energy, and the amount of current the batteries can accept falls off as they get closer to being fully charged.

Installation is $90/hour plus mounts ($15/panel), wire, connecting blocks, and other parts, and would take 4 – 5 hours to complete.  The owner assured me they would have it in and out in one day so we could be back in our parking spot before dark.  The last three weeks of January are the busiest time of year for Discount Solar and since we are plugged-in to shorepower we do not need the solar system right away.  If we have it installed in early February we would have a month to make sure it works and resolve any problems.  The system would cost about $3,300 installed.  We have at least a month to think about it.

When I returned to our coach Linda was out walking.  When she got back I went up on the roof with a tape measure to see if/how the solar panels might fit.  With a four-n-aft orientation we could put two towards the front outside edges, one just aft of the kitchen skylights on the driver side, and one aft of the hall skylight on the passenger side.  We could put two more somewhere in the rear.  The options for the rear appeared to be inline (almost touching) on the driver side starting just behind the bathroom skylight or putting one there and the other one sideways across the back just ahead of the dropped portion of the roof and aft of the bedroom vent fan.  Placing the panels in these locations would leave the center of the roof open so I could climb up on the driver side front and walk all the way to the back.

Barb stopped by to let us know there was a mattress in the house (park model trailer) if we wanted to try it out.  It had been in their rig for about two years until they removed it yesterday and replaced it with a thicker one they got from Connie.   It is a regular queen size mattress about 6″ thick, so not one of the oversized behemoths that have become the norm.  They also had a 1.5″ thick memory foam pad to go on top of it.  We took a look at it and decided to give it a try.

We have been using our old Select Comfort adjustable air mattress in the RV since summer 2013.  One side (mine) has a slow leak so I have to adjust it every other night.  I could live with that indefinitely but what we really dislike about it, and have for a long time, is that we tend to roll into the center or off the edge.  It also takes up valuable storage space under the bed for the pump, has wires and hoses to deal with, and has a controller for each side.  We were definitely ready to try something else so we stripped the bed, disconnected the two air hoses, and carried the mattress out of the bus.  It was surprisingly heavy and bulky for an air mattress and lacking in self-supporting structure, but that also made it easier to bend it around the front passenger seat, down the entry stairs, and out the door.  We stored it in the bedroom of the house trailer pending a final decision about the replacement mattress.

We carried the new mattress in, which was definitely easier than getting the old one out, and got it positioned on the plywood bed platform.  We put the memory foam pad on top and put our mattress topper over that which added another inch.  We put our electric heating pad on and then the sheets and the blanket.  We will try it out for a while and if we like it we will see if the Salvation Army wants the old one.  If not, it may end up at the Quartzsite dump as we really do not have any way to get it home or a reason to do so.  We will leave the pump, hoses, and controllers under the bed until we decide on its final disposition.

The suspension on the bus had settled slightly in the driver side rear since we parked and leveled it almost a month ago.  It would not have been enough to require an adjustment except that our bed sits crosswise with the head on that side and I find that sleeping with my head even slightly downhill is not comfortable.  Rather than start up the main engine we got the Dewalt portable air-compressor out of the car and connected it into the brake system fill port in the passenger side engine bay.  I had to connect the chassis batteries and turn the ignition on (without starting the engine) in order to activate the leveling controls, but that allowed me to raise that corner up and get the coach level side-to-side.  At some point we will re-position the bus, but not until I have completed some work on the turbo boost sensor mounting plate and hose and the level low system components for the front end.

We put the air-compressor back in its special storage divider in the car and decided to rearrange a few things so we could put the rear seat down.  Starting next week we will need to be able to carry a passenger.  We thought about heading down to the market area but remembered that we were expecting UPS deliveries.  I started working on two more articles for BCM instead while Linda went for a walk.  It was warmer today and so it was warmer in the coach and I ended up taking a nap.

Our UPS and FedEx shipments usually arrive late in the afternoon or early evening but had not shown up by dinner time.  I had planned to disassemble the Aqua-Hot burner and replace the bearings, nozzle, and perhaps a few other small parts tomorrow but it now appears that will have to wait until Tuesday, assuming our shipments arrive on Monday.  I will likely need to clean the unit as well, given that it has been running so rich, and that may include pulling the combustion chamber.

Linda made two cold salads for dinner; chickpea and wild rice Waldorf.  Both are favorites of ours, especially in warmer weather.  We had some Barry’s Basic Bread with our meal and another glass of Lamb’s Valley organic sweet white wine was a most agreeable accompaniment.

Yup, that's a real, live camel in the Hi Jolly Daze Parade. These animals are strongly linked to the 19th century history of Quartzsite, AZ.

Yup, that’s a real, live camel in the Hi Jolly Daze Parade. These animals are strongly linked to the 19th century history of Quartzsite, AZ.

2015/01/10 (S) Hi Jolly Daze Parade

Today was the annual Hi Jolly Daze Parade.  As first time winter visitors to Quartzsite there was no way we were going to miss this event.  I was up at 7 AM to make coffee and we were done with breakfast by 8 AM.  We checked the parade route online and figured we would go to the Quartzsite Improvement Association grounds as the parade ended in the parking lot there.  It was scheduled to start at 10 AM so we snagged Fonda about 9:40 and headed that way in the car.

When we got to Central Avenue and Main Street the police had Main Street closed so we could not turn left to get to the QIA.  I stayed on Central down to Kuehn Street and took it east over to the exit 19 overpass and back to Main Street.  On the way we saw Lloyd DeGerald’s motorhome parked along Kuehn with a big banner advertising his Aqua-Hot technician services.  I am hopeful that I will be able to repair both of our burners myself but if not Lloyd is the guy I would call, so I was glad to see that he is in town.  But back to the parade.

The police had Main Street closed on that end too.  We knew the parade started at Plymouth Avenue and Quail Trail so we headed in that direction and parked at the Quartzsite Library.  We were surprised that no one else was parked there as it was a short walk from there to the start of the parade route which turned out to be an excellent spot from which to view the parade.  What we realized after we got there was that the west side of Plymouth Avenue was lined with cars from the starting point all the way to Main Street.  I suspect that Main Street was similarly lined with people, most likely in cars, but we were not able to observe that directly.

We had a few drops of rain leading up to the start of the parade.  There were plenty of grey clouds around, but the sun was also shining and the parade did not get rained out.  In fact, a full 160 degree rainbow formed behind the parade and lingered until most of the participants had passed us.  The highlight of the parade was a live camel.

“Hi Jolly” was the Americanized pronunciation given to Hadji Ali, who came here in 1856 as part of an experiment by the U. S. Army in the use of camels.  There are conflicting accounts of his exact place of origin but it seems clear that he came to the U. S. from the Middle East as one of the first, and the lead, camel driver.  For a more complete account check the entry in Wikipedia for “Hi Jolly.”

The experiment did not work out as the Army’s horses, mules, and burrows were apparently terrified of the giant animals and would panic in their presence, but Hadji Ali remained in the U. S. and eventually ended up in Quartzsite where he died in 1902 and was buried in the local cemetery.  We got the impression that he was something of a living legend in his own time and in the 1930’s the governor of Arizona had a monument erected at Hi Jolly’s gravesite.  It is a small pyramid made of local stone with a metal plaque on one side and a metal profile of a camel on top.  According to Wikipedia the monument is allegedly the most visited location in Q.

When the parade was over we returned to our coaches.  Linda went for a walk and I wrote another article for Bus Conversion Magazine.  This was another short one, less than two pages and only 11 photos, on the installation of the new speedometer in our bus.  When Linda returned from her walk she made a broccoli-potato mash.  In addition to the broccoli and the potato it had soy milk, vegan butter, salt, and pepper.  The potatoes were not completely mashed and the dish was both tasty and had a nice mouth feel.

After lunch Linda made a shopping list.  We headed to the Kuehn Street market area and stopped at Barry’s Breads but our timing was bad, again.  We drove south on Central and found the entrance to the parking lot for “the big tent.”  This is where the RV vendors will be in another week or so, but nothing was open yet, so we went over to the Tyson Wells area west of Central Avenue and found some miscellaneous items and a pair of Crocs for me.  For all the shoes I brought I did not have something that was easy on, easy off.  We are parked on gravel and I needed something I could slip on quickly and easily to step outside the coach.

Most of Linda’s list was groceries so we drove to Blythe, California to do our shopping.  To vary our trip and see some new sights we stayed on Kuehn Street heading west past the edge of town where it became West Dome Rock Road.  The road parallels I-10 on the south side for a long way through BLM land and eventually ends at an interchange with the Interstate.  We saw lots of RVs, and a few tents, spread out on either side of the road, but not nearly as many as we thought we would.  There are probably a lot more RVs here than we realize, but the desert is a vast place.

When we got to Blythe we took a few minutes to drive through town and get a feel for the place.  It had a more developed, modern, and prosperous business district than Quartzsite and more houses, as opposed to park model trailers and mobile homes. The houses were not fancy but they were in decent condition.  Schools and municipal buildings were also nice, and there is nothing in Q to compare to the two supermarkets and name brand stores like Auto Zone, NAPA Auto Parts, and K-Mart.  We started at Albertson’s and got most of the items on our list.  We then went across the street to Smart and Final Express and picked up a few things there.  Once again we were not able to find the Silk brand Soy Coffee Creamer, which has us wondering if we last bought it at Wal-Mart in Parker.

When we got back to camp I unloaded the car and Linda put the food away.  I wandered over to say high to Butch and Fonda and play with their dogs, Daffy and Rascal, for a few minutes.  I then went over to say high to Jim and Barb’s dog, Roho, which brought them out of their motorhome and got me invited in.  Linda eventually wandered over looking for me and the four of us had a nice chat.  It was the first time since they got here that I had been inside their rig, a Country Coach Intrigue, and it was very nice.  It has one slide on the front half of the driver’s side, and there is no doubt that it really opens up the interior.  Before we bought our bus we were looking seriously at Country Coach motorhomes (but not their Prevost bus conversions) and the Tiffin Allegro Bus (which is a purpose-built motorhome, not a true bus).  But in the end we were bitten by bus fever and we still have it.

We stopped to visit briefly with Butch and Fonda on the way back to our rig.  Butch has always had an interest in metal detecting and has developed an interest in rocks since arriving in Quartzsite.  If you had the slightest inclination towards rocks, gems, and minerals then being in Quartzsite during the winter would likely push you over the edge into a full-blown hobbyist.  Sometime in the last couple of days Butch bought a used contraption that consists of a table saw, two grinding wheels with a water delivery system, and an electric motor.  He and Fonda acquired a bucket of rocks, including a piece of petrified wood, and they are setting up an area outside their bus to work on their new hobby.

For dinner Linda made pan-grilled tofu slices with caramelized onions and bar-b-cue sauce, but with a twist.  Instead of hamburger buns or slices of bread she heated 12″ tortillas and made wraps.  Of the various ways she has served this simple, but delicious, dish this was definitely my favorite so far.  As much as I like a nice, fresh bun the tortilla wrap kept all of the ingredients contained so that I got onion and BBQ sauce with each bite, and they did not end up all over my plate and all over me.

As we do most evenings, we relaxed, played games, worked puzzles, read, and wrote. We are always a bit surprised at how tired we are after dinner, but we are up and about during the day and the fresh air and sunshine just seem to wear us out.

The roof of our bus after cleaning looking SW as viewed from the driver side front corner. Quartzsite, AZ.

The roof of our bus after cleaning looking SW as viewed from the driver side front corner. Quartzsite, AZ.

2015/01/11 (N) Swimsuit In January

I turned the lights off last night at 11 AM and was up at 7 AM this morning which seems to have become my current routine.  Because of the new (to us) mattress I was able to get up without waking Linda up.  I turned up the heat in the front of the coach but not the back as Linda does not sleep well in a warm room.  I started getting the coffee ready but did not grind the beans because of the noise it makes.  I worked at my computer on organizational tasks such as copying files to the NAS, copying blog posts from e-mail to Word, and backing up website and photo files to the NAS.

Linda got up around 8:30 AM and set the microwave convection oven to preheat in convection only mode.  When it was ready she heated up the leftover cinnamon raisin rolls she took out of the freezer yesterday and put in the refrigerator.  While the rolls were heating I finished making the coffee.  Although they are not gigantic, one of these rolls would probably be plenty of calories for breakfast.  Two rolls, however, made for a very satisfying meal.  Still, they take about four hours to make fresh and about 25 minutes to reheat.  She makes a batch of eight, so if we each had one for breakfast her efforts would cover four meals instead of two.

Today was another bus cleaning day, but first Linda went for her morning walk while I continued to organize photo files on our network attached storage device.  It was forecast to be a cloudy but mild day and by late morning the clouds had moved in, so when Linda got back we got busy.  Even with the cloud cover it was warm enough that I was able to wear my swimsuit and a T-shirt, my preferred outfit for working with water.  We bought some CLR Mold & Mildew remover yesterday and I tried using it on the lower rear roof.  It did not appear to have any effect so I abandoned any further roof cleaning and we got started on the sides.

The upper sides of our bus are not easy to clean.  Even with our Little Giant extension/step ladder set up as a step ladder at its maximum height I cannot quite reach the top curve of the side walls.  Knowing that was the case I cleaned all the way around the edge of the roof, where it meets the side walls and the front and rear caps, from the roof.  Once I was done with that we took the Little Giant extension/step ladder and converted it from extension configuration to step ladder configuration.

We worked all afternoon until after 5 PM and managed to clean the front and the passenger side.  We wanted to get the passenger side done because it faces south and we wanted to do this on a cloudy day.  Working a section at a time we used McGuire’s red automotive soap, scrubbed with an automotive microfiber sponge, rinsed thoroughly (with Q’s incredibly hard water), and dried with microfiber clothes.  We could not get all of the hard water stains off but it was a lot cleaner, and looked a lot better, than when we started.

The weather forecast for tonight was for heavy rain sometime between 9 and 11 PM with accumulations of up to 1/2″.  For a place that typically only gets 4″ of rain a year that would be a lot of rain for one storm.  We put our lawn chairs, mats, and other outdoor items in the carport for the night just to be safe.  Shortly after 6 PM we had our first sprinkles.

For dinner we had chickpea salad and wild rice vegan Waldorf salad with strawberries and peach slices and some Barry’s Basic Bread with a small glass of Franzia Fruity Red Sangria.  I responded to some e-mails after dinner and deferred work on possible survey questions for the FMCA national education committee until tomorrow.

Linda makes her selections at the Quartzsite Farmers Market.

Linda makes her selections at the Quartzsite Farmers Market.

2015/01/12 (M) E-mail Groups

It has stayed warm enough the last few nights that I have not needed the electric heating pad and we have been able to leave windows slightly open.  We both sleep better in a cool room with fresh air.  The deluge of rain that was forecast for last night did not develop but it was still mostly cloudy when we got up this morning.  After breakfast, coffee, morning puzzles, and checking in with the world we got on with our chores.

My major tasks for the day revolved around preparations for, and participation in, a 2 PM FMCA National Education Committee work session.  While I worked on that stuff Linda went for her morning walk, made an appointment to get her hair cut tomorrow, and made garlic naan (Indian bread) from scratch.  When the phone meeting was over I transferred photographs from my camera to my computer and then joined Linda over at Butch and Fonda’s coach for a late afternoon visit.

Jim L. showed up while we were chatting, read the electric sub-meters, and figured out our bills.  Linda had to write four separate checks to cover our site fee, electricity usage, laundry, and the rental for the apartment, which Jim gave to Barb to cover the cleaning before and after Marilyn’s upcoming visit.  Butch placed an order with PartDeal.com for a VDO speedometer so I had him order a VDO Cockpit Series 0-30 PSI Boost Gauge for me.  The UPS truck also showed up and had the two packages I have been waiting for.  All too soon the sun dropped below the western mountains and it turned chilly so we retreated to our coach.

Linda made curried red lentils for dinner and served it along with the garlic naan bread she made earlier in the day.  Warmed and energized by this fabulous meal I launched into my second major task of the day; the creation of an e-mail group in Microsoft Outlook for our FMCA Great Lakes Converted Coaches chapter.  I got the latest roster from Linda, who is the treasurer, and was able to rearrange it, save it as a CSV file, import it into Outlook, and map it to the standard contact fields.  It was then easy to create a Contact Group and select all of my new entries to go in it.  Once I got the group set up I wrote an e-mail to the members, my first since being elected President of the chapter back in October.  I was up much later than usual, but I got it done.

Escapees RV Club happy hour SE of Q in one of the BLM STVAs.

Escapees RV Club happy hour SE of Q in one of the BLM STVAs.

2015/01/13 (T) Geekiness

Today was a day for Geeks and geekiness.  Chris and Jim Guld, AKA The Geeks On Tour, arrived in Quartzsite yesterday and are staying at an RV Park not far from our encampment.  Butch knew they were headed this way and after he and I were unable to get EchoLink working on his computer yesterday he contacted Jim to see if he would be willing to stop by and take a look.  Jim is a former network administrator and knows a lot more about stuff like networking, protocols, ports, port forwarding, and proxy servers than we do.  But before he came over Linda and I had breakfast after which she walked over to the beauty parlor and got her hair cut while I worked on a seminar classification task for the FMCA National Education a Committee.

Jim G. arrived on his bicycle around 10:30 AM and stayed for a couple of hours.  He re-checked the things Butch and I had already tried and tried some things we had not, but we could not get Butch’s system to let the EchoLink program connect successfully to the EchoLink servers.  For the record, Butch’s system consists of a Windows Vista laptop that connects to the Internet one of two ways:  1) through a Verizon MiFi or,  2) through a WiFiRanger Go2 into a WiFiRanger Mobile into a DSL WiFi gateway of unknown make and model.  Jim also tried connecting through the WiFi hotspot on his Android-based smartphone.  Same result.  Mixed in with work we had a great visit with Jim and hope to meet up with he and Chris at least once while they are in Q.

After Jim left Linda and I were headed in to have a bite of lunch when an unfamiliar car pulled into the lot.  Barb was by the road and pointed the driver in our direction.  We quickly realized that it was Mara.  She had called Linda first but Linda did not hear the phone ring so it was a wonderful surprise when she showed up.  We visited for a couple of hours while we snacked on hummus, pretzels, and red grapes.

Mara is camped on BLM land north of town with the WINs (Wandering Individuals Network) and has been traveling off and on with groups of WINs since we last saw her in Gillette, Wyoming in July 2013.  Since that time she has also gotten a different motorhome, a 35′ Fleetwood Bounder, with which she is very pleased.  She invited us to join a group of WINs on Sunday to go to The Desert Bar and I think we will.  Linda checked it out online and it is a completely solar-powered, off-the-grid, place.  You have to take dirt roads or ATVs to get there.

It appears that things are finally going to get busy for us.  Gary, from BCM, is supposed to arrive tomorrow and Curtis, from RVillage, is supposed to arrive on Saturday.  Forrest and Mary are already here as are Chris and Cherie of Technomadia.  The Escapees RV Club has happy hours scheduled tomorrow and Thursday at one of the BLM areas east of town.  Blythe, California has a bluegrass festival starting Friday and running through Sunday.  We will probably go on Friday as there is also a Balloon Festival in Lake Havasu the same three days which we will probably attend on Saturday.  Somewhere in there I need to repair our Aqua-Hot and I am thinking that it will probably be Thursday.  The “Big Tent” Sports, Vacation, and RV Show starts on Saturday (17th) and runs through the Sunday the 25th.  Marilyn arrives on the Thursday the 22nd and leaves on the Thursday the 29th.  The last full week of January really is the peak of the winter season in Q.

After Mara left I used my macro lens to photograph the front and back of both of our amateur radio operator licenses.  I post-processed the images to improve the readability and reduce the file size.  Once I had the photos ready I downloaded and installed the EchoLink software on my Asus laptop.  I went through the initial configuration for my license and tried the server connection test.  As with Butch’s installation, two of the four UDP port tests failed.  I ignored that for the moment and went ahead with the validation procedure for my ham license.

Anyone can download and install the EchoLink software but only licensed hams can legally use it.  That is because it can, and often does, connect a computer to a ham radio repeater that is “on the air” and only licensed hams are allowed to transmit on those frequencies.  Validation was a multi-step process.  When first starting EchoLink I had to supply my FCC callsign, name, and (base station) location.  That information was transmitted to a database on the EchoLink servers but the EchoLink organization needed to validate that I was actually the person to whom that callsign was issued.  Through a separate process on the EchoLink.org website I had to upload JPEG image files of the front and back of my wallet license.  Once someone examined the images and made sure the call was active in the FCC database they “flipped the switch” on the server side and I was finally able to connect to stations if I wanted to.  I repeated the process later for Linda’s license.

While I was waiting to have my license validated I started trying to figure out how to get the EchoLink program to connect successfully to the EchoLink servers.  When the communications test with the servers runs it identifies the IP address assigned to the computer.  I went into the WiFiRanger Mobile and enabled UDB port forwarding for ports 5198 and 5199.  The TCP test was successful so I did not set up TCP port forwarding for port 5200.  Enabling port forwarding, however, was necessary but not sufficient.

What I ended up doing was switching the operating mode on the ESET Smart Security program from “Automatic” to “Interactive.”  With that change, the program would pop up a message box every time another program had outbound or inbound traffic through a port and ask if I wanted to allow the communication and optionally create a rule for it.  Several of those messages had to do with EchoLink and after clicking “Allow” to all of them the server/router tests were finally all successful and the program was fully functional except for the license validation.

Sometime in the late afternoon another motorhome showed up and backed in to the property with Jim L.’s help.  It was Larry and Sandy, who normally stay at Jim L.’s RV Park near the QIA.  Jim’s park is full so he put them over here in the spot by the laundry where Jack and Maria parked for a couple of nights a week or so ago.

We had leftover red lentil potato curry (thick soup) for dinner with the rest of the garlic naan and a glass of sangria and it was very good, again.  I finished up my FMCA education committee task and e-mailed it off.  I received an e-mail that my ham license had been validated so we played with the EchoLink program and User’s Guide for a while but did not try to connect to any stations.

While I was working on all of this I noticed that nine updates were pending for Windows 8.1 and there were four optional ones as well.  Installing updates is often an iterative process and so it was again this evening.  One of the optional updates was a roll up from November 2014 that was 723.9 MB.  That’s a big update.  I started downloading it at 23:52 MST and then went to bed.  My hope was that fewer people would be trying to use the local DSL system to get online at that hour and the update might actually load and install successfully.  But I would have to wait until tomorrow morning to find out.

L-to-R: Travis & Melanie Carr from the Escapees RV Club and Cherie Ve Ard & Chris Dunphy of Technomadia.

L-to-R: Travis & Melanie Carr from the Escapees RV Club and Cherie Ve Ard & Chris Dunphy of Technomadia.

2015/01/14 (W) SKP Happy Hour

As soon as I got up this morning I checked the huge Windows 8.1 optional rollup update that I started last night.  It had completed successfully except for restarting the computer, so that’s what I did.  While the update finished installing I made coffee and got the juice ready and Linda prepared our cereal.

Once the update finished I checked e-mail and websites.  Linda made white bean hummus to take to the SKP Happy Hour later today.  She then remembered that the Farmers Market at Desert Gardens was this morning from 8 AM to noon so we drove over there.  There was only one stand selling produce, but they were from Blythe, California only (20 miles away) so the produce was very local and very fresh.  Linda bought an assortment of veggies and a grapefruit.

We had parked at the south end of the western parking area and from there we could see a road going back towards “Q” Mountain and a well-defined trail going up the western side.  We drove back there and determined that we could park there when we decide to climb the mountain and do some panoramic photography.

We drove to Barry’s Breads and bought a loaf of Barry’s Basic Bread and then continued east on Kuehn Street to confirm Lloyd DeGerald’s location.  We took Riggles Avenue back over I-10 to Main Street and headed back towards Central Avenue, stopping at the Road Runner Market for a few things.  When we got back Jim and Barb were aggressively trimming the Palo Verde trees in the cactus garden.

As we often do most mornings, Linda went for a walk and I worked at my computer, installing three more optional updates and taking care of some e-mail.  We gathered up chairs, food, and beverages at 12:45 PM and drove over to the SKP Happy Hour on East Dome Rock Road.  There was already quite a crowd when we arrived and everyone was in a good mood.  And why not.  The sun was shining, the air temperature was pleasant, there were tables arrayed with food, people had beverages of their choice, Johnny Cockrum was performing, and lots of folks were meeting old and new friends.  We had a thoroughly pleasant time, but we always do when we are with groups of Escapees.

On the way back to camp we spotted Lloyd DeGerald and his wife out walking their dog and stopped briefly to chat about our Aqua-Hot.  We then stopped at the trailer for the Two Crazy Ladies and ordered engraved hang tags with our call signs and a sign asking emergency responders to rescue our cats.

When we got back to camp Linda went for another (short) walk and I sat down to work at my computer.  We lost our Internet connection while we were away and the DSL gateway would not re-associate with our WiFiRanger Mobile so I had Barb open the house and I power cycled the gateway.  I was then able reestablish the connection to our WFR-M.  That is the second time this has happened since we arrived here but so far has not caused us any real difficulty.

Butch has been having problems with their Progressive Industries EMS cutting off their shorepower due to high voltage.  We noticed during dinner that our PI-EMS was also showing a PE-3 (previous error – high voltage).  I do not know if our Magnum inverter switches on “instantly” when outside power is lost or if there is a delay but I am now wondering if we lost our Internet connection due to loss of power to the WiFi Ranger Mobile after which it was not able to reconnect with the gateway.  The next time this happens I may try powering the WFR-M off for 60 seconds and restarting it.  It’s also possible that the high voltage is wreaking havoc on the DSL gateway.

After dinner I sent a TXT message to Gary at BCM inquiring if he had arrived in Q as planned.  He called back and said they had just cleared Indio, California.  I suggested they find someplace to stop and rest and finish the trip tomorrow morning in the daylight.  They are headed to the Quartzsite Market Place dry camp area for the Eagles International bus gathering.  I spent the rest of the evening working on five different articles for Bus Conversion Magazine before finally turning in around midnight.

 

2015/01/01-07 (R-W) Q 2015 W1

Leave a reply

2015/01/01 (R) Hola 2015

The salt restraining tube for the water filter housing. The slotted end (R) goes down and the o-rings sit in the other end.

The salt restraining tube for the water filter housing. The slotted end (R) goes down and the o-rings sit in the other end.

Having stayed up later than usual last night to see the old year out and welcome the new year in we were in no hurry to get up this morning, especially given that the temperature outside was in the upper 20s.  But Linda said she would make her yummy vegan cinnamon rolls for breakfast so I felt obligated to get up and eat them.  Besides, it’s my job to make the coffee.  The rolls took quite a while to make and we ended up having them for brunch, but they were worth the wait.

I spent much of the morning looking for new games in the iStore.  I downloaded a dozen free ones and then started trying them in turn.  Most of them immediately tried to sell me a full version or ran a full-screen advertisement each time I tried to start a new round of play.  If they did that I immediately deleted the app.  I cannot imagine what makes a game developer think someone with tolerate that more than once.  At some point I realized that my AppleID was still associated with an old e-mail address so I initiated the process of changing it.  The process was not as seamless as I thought it could/would/should be, but I eventually got it sorted out.  Or as they say or Doc Martin, “sorted.”  As it turned out my credit card information was also out of date so I updated that as well.  Obviously I do not make iStore purchases very often.

I needed to regenerate our portable water softener even though it was 48 degrees F outside in the shade.  It was, however, comfortable enough in the sun to be able to work.  I started at noon cutting the plastic drain pipe that I bought at Herb’s Hardware the other day to a length of 10″ which is the length of a standard water filter.  I cut eight 3/8″ slots in the bottom end of the tube and got an O-ring from Butch to fit in the swaged upper end.  The purpose of the tube is to hold salt so that incoming water is required to pass through it to get to the softener but the salt crystals cannot actually wash into the softener.

Linda helped me transfer the contents of a 40 pound bag of solar salt to several two-gallon zip lock bags.  I then put a small quantity of salt in a one-quart zip lock bag and gently smashed it with a two-pound sledgehammer, although as I write that it seems to be something of an oxymoron.  I inserted the tube into the removable filter housing, slotted side down, and poured the salt around the outside of the tube.  I smashed a second bag of salt and added it to the housing.  I put the housing back on the filter head and slowly ran water through the softener for almost two hours.  I got a water hardness test strip from Butch and tested the output of the softener.  It was still showing 7 grains of hardness, exactly the same as two days ago.  It appeared that the regeneration process had not had any effect.  Bummer.

I discussed the situation with Butch and he suggested I back flush the softener.  To do that I needed a hose with female hose fittings on each end.  This is the kind of hose used to hook up a washing machine but neither one of us had one with us.  Butch, however, had a female-female adapter which allowed me to connect a male hose end to a male fitting on the outlet of the water softener.  (Backflushing literally means running water through the softener in the reverse direction to flush out any debris that may after gotten in through the normal inlet.)

The salt retaining tube in the filter housing with salt around the bottom outside and the o-ring visible at the top.

The salt retaining tube in the filter housing with salt around the bottom outside and the o-ring visible at the top.

After backflushing the softener I tried regenerating it again.  This time I used a 26 ounces of fine grain non-iodized table salt.  With my homemade diverter tube still in place I added the salt around the outside and screwed the housing back on.  I let the salt sit in the housing for 20 minutes to start to make a brine and then ran water through the softener until I got a very salty taste at the output.  I then shut the outlet valve and let it sit for 20 minutes.  When the time elapsed I ran water through the softener for another 15 seconds, checked it for saltiness, and shut the outlet valve.  At the end of another 20 minutes I ran water through it at a very slow rate for 20 minutes and then checked it again for salty taste.  It was still slightly salty and as it was getting close to sunset I decided to let it sit overnight.  I will finish flushing it tomorrow and check the hardness again.

While I was fussing with our water softener Butch recharged theirs in about 30 minutes.  When he tested the water at the end it indicated zero (0) grains of hardness; completely softened.  Their softener is different from ours and the regeneration procedure is very straightforward and apparently works.  For now I need to figure out a guaranteed procedure for regenerating ours, but long-term I need to figure out some other arrangement of just get a different softener.

The arrangement I am considering would be in conjunction with redoing the water bay. With a different arrangement of tanks I could create space in the bay for the softener, multiple filter housings, and associated plumbing.  I could set up an arrangement that would divert the incoming water (after the first/sediment filter) through a clear filter housing into which I could put the salt.  That clear housing/head would be permanently modified to force water through the salt and allow me to see when the salt was gone.  It would also eliminate the need to remove and reinstall the filter the way I have to now.  Alternatively I could put a tank between the filter housing and the softener (instead of the clear housing) and use it as a brine tank.  If the tank was big enough to hold a 40 pound bag of solar salt it would work just like a home softening system.  Water would sit in the tank with the salt for days so that the brine was ready to use when it was time to regenerate the softener.  I could even rig up a separate pump just for pumping the brine into the softener.  I’m going to give this a lot of thought before I start changing things around, but last winter in Florida and this winter in Quartzsite have made it very clear that hard water is a problem and we need a very effective and efficient way to deal with it.

While I worked with the water softener Linda began preparing a Tex-Mex bean soup for dinner and then went for a long walk.  She finished making the soup when she got back while I took a short nap.  It cooled off quickly as the sun set and nothing is quite as satisfying on a cool evening as hearty, hot soup.  It also had a bit of red pepper heat which was a nice bonus.  It was really good soup.

I had a few e-mails from Gary at BCM and a nice follow-up e-mail from Kathy at the Michigan Assessment Consortium.  She attached a copy of their holiday letter so I attached a copy of ours in reply.  I spent a little time browsing websites for OTA TV antennas and turbo boost gauges and finally went to bed without resolving what to do about either thing.  I have a lot of nights that end like that.

2015/01/02 (F) Crazy Days In Q

Contact is established with our cat, Jasper.

Contact is established with our cat, Jasper.

The “show” at Desert Gardens officially opened yesterday and runs through the end of February, so Quartzsite is quickly be transformed into a crazy place.  We were chatting with Butch, Fonda, Jim, and Barb after breakfast and Barb reminded us that starting now driving and parking “downtown”, and especially along Kuehn Street south of I-10, during the day will be difficult to impossible.  She offered to drive us down in the golf cart and come pick us up if we did not want to walk.  She also told us that many vendors will hold purchases for pickup at the end of the day.  We exchanged cell phone numbers, which we had not yet done since they arrived.  She suggested that if we wanted to eat out we should go early or right before closing as we might not be able to get seated/served otherwise.  There’s no doubt that we have lucked out on our arrangements this winter, and the situation just keeps getting better.

Linda was browsing on her iPad and discovered an all vegan grocery store in Rancho Cucamonga, California; the largest all-vegan grocery store in the world.  I looked up Rancho Cucamonga on Google Maps and it is located about half way between Los Angeles and San Bernardino.  Based on the speeds I like to drive (often just below the speed limit or 68 MPH, whichever is less) it looks like a four hour drive one-way from Q.  That’s obviously too far for a regular grocery run, but we might make a day trip in that direction sometime this winter and find the store while we are over there.

One of the things I did after climbing in bed last night was spend a little time looking at the Sure Marine Service website.  SMS is a major supplier of repair parts for Webasto diesel-fired hydronic systems headquartered in Seattle, Washington.  After studying their parts diagrams I became unclear (and concerned) as to whether the burner we removed from Butch’s old unit was a DBW2010 or a DBW2020.  They are very similar but not identical.  I am almost certain that our original burner is a DBW2010, but our AHU-xxx Aqua-Hot is so old that the model number is no longer referenced on the website and model specific documentation, like a service manual, is not available for download.

The reason I was looking at the parts diagrams was to identify the bearing kit for the blower as I wanted to order two of them today.  What I could tell from the website was that the 2020 is a higher BTU output burner and so one of the differences is that the 2010 uses a 0.35 GPH nozzle while the 2020 uses a 0.60 GPH nozzle.  That alone might account for why we seem to have poor combustion, although even money is still on bad bearings.  The unresolved issues and the inability to investigate at midnight did not make for a good night’s sleep.

I have the Aqua-Hot service/repair manual for the unit I bought from Butch, both on paper and on my iPad, so I spent some time this morning looking at the iPad version.  I could not tell if they used the same bearing parts so I did not order anything today and won’t until I can determine model numbers.  I asked Butch if he knew which burner was in the Aqua-Hot I bought from him, but he did not.  The service manual shows a Webasto label that identifies the burner model, but does not show where the label is located.  More investigation was needed.

After I got dressed I e-mailed Bill Gerrie (RetiredBusNut) in Ontario, Canada with questions about gauges and sending units for our bus engine and transmission.  I then started dealing with the water softener.  Linda returned from her walk and started preparing lunch, so I emptied the filter housing of the little bit of salt that was still in the bottom, rinsed it clean, re-installed the filter, and let it run for 20 minutes to fully flush out any residual salt water.

Linda made a warm garbanzo bean and kale salad for lunch with lemon juice and garlic.  It was the first time she had tried this recipe and we both agreed it was a keeper. After lunch I tested the hardness of the water coming out of the softener and it registered on the test strip between zero (completely soft) and 1.5 (definitely soft) so I dumped the remaining (hard) water in the fresh water tank and refilled it with 120 gallons of nice, soft water.  After the tank was full I retested the water coming out of the softener and got the same reading as before.  Finally, some good news on the water softener front.

With water softening taken care of (for now) I did an online search for a panoramic camera tripod head.  I really like shooting panoramas and the Microsoft Image Composite Editor (MS-ICE) does a remarkable job stitching images together.  Most of my panoramas have been handheld, which makes the performance of MS-ICE all the more impressive.  I have shot a few panoramas using a tripod but without a nodal point (spherical) pan head, so that is what I was searching for online.  B&H Photo had a Manfrotto on sale for $280, marked down from $600, but their order desk was closing for the day and I did not want to be rushed making this decision so I did not order it.  They will reopen tomorrow, so I will think about it overnight and do some more research.

I got our old Webasto burner out of the front bay and found the label.  It is, indeed, a DBW2010, specifically a DBW2010.75 with a 0.35 GPH nozzle rated at 45,000 BTU.  Linda recorded the details, including the serial number, and then helped me rewrap it in bubble wrap so I could put back in its storage pail.

Linda then went to Parker, Arizona with Butch and Fonda to check out the Safeway grocery store and look for some things at Walmart.  The Parker Safeway was supposed to carry Daiya vegan cheese products but they were nowhere to be found.  It appears that our closest source will be Whole Foods.  There are five of them in the greater Phoenix area but that is a two hour drive one way.

While the three amigos were gone I removed the cover from the Aqua-Hot in our coach and found its label.  Much to my relief it is also a Webasto DBW2010.75, 45,000 BTU.  It should also have a 0.35 GPH nozzle, and probably does, but I did not pull the burner out to check.  I noticed some soot on the final fuel filter inside the housing and in other places so that gave me something new to be concerned about.  I was pondering the situation when Jim and Barb and Roho came over to visit and we had a good long chat.  When they went back to their motorhome I put the cover back on the Aqua-Hot and put all of my tools away.

My plan for tomorrow is to turn the Aqua-Hot off, let it cool down, and pull the burner to check the nozzle.  It’s possible, though not likely, that I do not have the burner seated quite right and there’s a chance, though very small, that reinstalling it will fix, or least improve the performance.  My money (literally) is still on the blower bearings.  Hopefully it does not also need a new motor as everything on a Webasto is more expensive than seems reasonable. It’s another fine example of precision German engineering and manufacturing.

Even though I have quite a few e-mail addresses that I use to segregate electronic correspondence into manageable categories my inboxes still end up flooded with e-mails.  Very few of them are spam—we have good spam filtering on all of the accounts—but some of the highest volume inbound traffic is notifications of things like failed login attempts on WordPress websites.  Those e-mails do not get replies and often do not require any specific action on my part, but they sometimes obscure the presence of other e-mails that do require my attention.

Microsoft Outlook is able to deal with incoming (and outgoing) e-mails based on user-defined “rules” but I had never played with that feature until today.  I used the online help system to read about the whys and wherefores of e-mail rules and then tried creating some.  Once I understood what I was trying to accomplish it was mostly point and click to get it done, with a little typing thrown in.  What I ended up doing was creating sender/subject subfolders under the inbox of certain accounts and then creating a rule for each subfolder that directs incoming e-mails matching the criteria to the correct folder.  By keeping the sub folders under the inbox folder it will be clear to me that these are e-mails that I have received but not yet dealt with.

For dinner Linda made a cooked shredded Brussels’ Sprouts dish with tomatoes, dried cranberries, and pistachios and served it alongside the leftover Mexican rice with a glass of sangria.  Ole!  We agreed that both of these dishes were keepers and went well with the fruity wine.  The rest of the evening was quiet.  Linda read and played her online games while I finished up working on this post.  I finally went to bed and started reading the service and repair manuals for the Aqua-Hot system and the Webasto burner.  According to the long-term weather forecast tonight should be our last night with an overnight low temperature below freezing.

 

A few of the vendors at Desert Gardens, Quartzsite, AZ.

A few of the vendors at Desert Gardens, Quartzsite, AZ.

2015/01/03 (S) Hammer Stahl

I got up at 6:30 AM today.  I had been awake for a while before that and had some things I needed/wanted to do on my computer.  These were quiet tasks that I could do in the front of the coach, with the heat turned up, without disturbing Linda.

I always check my e-mail first.  There was a group message from Hillary at RVillage to all of the Ambassadors regarding a new feature they will be rolling out soon and seeking our assistance.  I mentioned this to Linda when she got up and we watched the two YouTube videos.  We did not have time today but will work on it tomorrow in advance of a 5 PM (4 PM PST) web meeting.

My first project today was updating the spreadsheet I maintain for our FMCA Freethinkers Chapter, which I started working on last night.  The chapter treasurer maintains our checking account but as the secretary I maintain the records including the roster and who has paid their dues for what years.  Because I have all of those details I also generate the quarterly and annual financial statements.  I entered the information for dues payments that had been received between November 1 and December 31.  I then added the five worksheets for 2015 (four quarters and year), which tie together and link back to the 2014 statement, and updated the cumulative financial statement.

Linda got up so I put my work aside to make coffee while she made breakfast.  We had a few bananas that were ripe so she made green smoothies for breakfast.  We happen to like kale but if we didn’t, green smoothies would be an excellent way to get our daily dose along with several other healthy ingredients.

We talked about visiting the market area today and decided to go later when it was a bit warmer.  The temperature a 9AM was still only 40 degrees F so Linda bundled up and went for her morning walk while I continued to work on my spreadsheet.

Once I finished the spreadsheet I worked outside for a bit.  I removed the cover from the burner end of the Aqua-Hot while it was running to check for an exhaust leak (sight, smell, touch) but I could not detect one.  When the cycle finished I turned the burner off.  My plan was to let the unit cool off and then remove the burner to check the nozzle size and do a general inspection of the combustion chamber and visible parts, but that did not happen today.

What I did instead was return to my computer and start putting Webasto repair parts in my shopping cart on the Sure Marine Service website.  The bearings on the installed burner are definitely whining and need to be replaced.  They are supposed to be replaced regularly anyway, so I put two sets in the cart.  It is very likely that they are causing the motor to run slow which means insufficient combustion air, and possibly lower fuel pressure, leading to the dark smoky exhaust.  I also put a fuel solenoid valve in the cart.  There is a good chance that the valve and/or the solenoid are not working on the other burner.  There’s also a chance that the ignition coil has failed, but the solenoid valve costs 1/2 as much as the coil, so I’m hoping it’s the valve.  I got the order submitted with UPS ground shipping and used PayPal to make the payment.

Once I completed the SMS order I loaded the B&H Photo app onto my iPad and spent quite a bit of time going between their website and the Sony online store trying to figure out if I should order a panoramic tripod head and/or new camera, possibly with a lens and flash unit.  Sony has the Alpha 99 FF body marked down from $2,800 to $1,900 with the vertical grip and an extra battery thrown into the deal, an additional $500+ value.  They will also bundle in the SAM 28-75mm f/2.8 lens for $400.  The lens by itself is normally $900, so that’s another $500 savings.

So for $2,500 I could get $4,200 worth of Sony’s top-of-the-line “flagship” DSLR (DSLT, actually) equipment, except for one thing; it was all on back order with an ESTIMATED ship date of February 4, 2015.  That’s my birthday, so if it actually shipped on that date it would be quite the birthday present, but if it was delayed very much there would be the very real possibility of it arriving at our location in Q after we had left.  Not good.

So what about B&H Photo?  It turns out that they (claim to) have all of these pieces in stock and they are selling the body with the added pieces for the same price as Sony, but they are not offering the lens at the bundled price.  That was the deal breaker that saved me spending a lot of money today.  Besides, I have been waiting a long time for Sony to officially announce and the ship the new (rumored) flagship alpha a99-II with its 36MP FF 35mm sensor and long list of awesome features.  To decide now to by prior generation technology it would have to be a very attractive deal, much better than what I was seeing online.

I ended up ordering a Manfrotto Nodal Point Pro panoramic tripod mount from B&H.  It should be here by the end of the week.  When it arrives I think we will hike up to the top of “Q Mountain” and try to capture the true essence of Quartzsite in the winter, which is RVs from horizon to horizon.

We headed down to the market area on Kuehn Street with Butch and Fonda and walked around for a couple of hours in the Tyson Wells Show grounds north of Kuehn Street and west of Central Avenue (US-95).  This particular market area had really filled up with vendors in the last few days.  Linda bought a nice white apron and really nice Hammer Stahl 5.5″ Santoku knife.  She checked online when we got back and she paid about 55% of the MSRP on the HS website.  She bought it from Cutlery by LeClaire, which also has a website, and has it on sale for $20 more than the price on the HS website, marked down $20 from their “regular” price.  The point is, she got it for what appears to be a good price of $59 and it came in a nice box with a ceramic sharpener thrown into the deal.

We drove farther west on Kuehn Street and pulled into the Desert Gardens show grounds.  It was getting near sunset, so we did not stay long, but Linda and I walked enough of it to get a feeling for the place.  It was a “rougher” setup than Tyson Wells and many of the booths were selling large, rough rocks and gemstones.  The vendors also had a lot more equipment set up and were using it to process materials.  We’ll be back, probably more than once, and earlier in the day so we can spend more time.

When we got back to our motorcoaches Fonda came over and worked with Linda for a little while on their business records.  We then had a nice salad and some of the spicy bean and pasta soup (that Linda made the other day) with crackers and sangria.  I spent more time after dinner researching stuff on my iPad and working on this post.

We appear to be in one of the few places in the country that is not getting clobbered by bad weather. The temperature is not even supposed to drop below freezing overnight. It will still be cool tomorrow, however, and we did make specific plans before going to bed.

 

A view of "Q" Mountain from the Desert Gardens Show area.

A view of “Q” Mountain from the Desert Gardens Show area.

2015/01/04 (N) Our Village

We had vegan pancakes for breakfast which prompted me to suggest that Linda invent some recipes, even if they are interesting and successful variations on existing ones, and feed them to our grand-daughter.  Linda could put them on our website using the WP Ultimate Recipe plug-in and, if they met with her approval, name they after “Bitty” (youngest grand-daughter’s latest nickname, although I think I will always prefer “Schmoo”).  Perhaps Pancakes Madeline; Sautéed greens a la Madeline; Pasta Madeline; or Madeline’s vegan mac and cheese.  Being retired gives me a lot of time to think.

Joe’s brother, Jim L., finally returned from Nevada today and was able to get the park model trailer unlocked.  Barb has been wanting to get in and clean it since she and Jim (different Jim) arrived.  Barb is a keep busy kind of gal.  She is responsible for maintaining the apartment and laundry room while she is here and told Connie she would also do some deep cleaning on their house trailer, so it’s been bugging her that she could not get in to do it.  As for my part, all I did was lock the door on the trailer the way Connie asked me to.  Barb and Jim (husband) had lots of keys but could not get any of them to work.

 

Today was shower day.  This is always more of a production than we would like because we keep the cats’ litter tray in the shower.  Most of the time that works really well—it is out of the way and contains any mess they might make—but it is inconvenient when we want to use the shower for its intended purpose.  Besides pulling the tray out into the hall by the bathroom door we have to clean up any stray litter in the shower to make sure it does not end up in the gray water waste tank.  Litter tray or not we still have to spray the shower walls when we are done, squeegee off the glass door, let everything dry, and then reassemble it as a giant cat litter box.  But it works and it’s one of the compromises we willingly make to live with our cats in so few square feet.

 

Once I was dressed I went outside to chat with Jim L. (Joe’s brother) and we discussed the possibility of upgrading the electrical service at our site to “50 Amp” (240VAC, 50A, 4-wire, the equivalent of a 120VAC, 100A residential service).  It’s not an issue for us right now as the cool weather has us burning diesel fuel to make space heat, but once the weather turns warm we may need our air-conditioners.  We have three but can only run one on a “30A” service and still have enough power to run other things.  A 30A service is just what it says; 30A of current at 120VAC.  A “50A” RV service is slightly more than three times that amount of power.

 

The electrical hookups here are very interesting.  Perhaps all RV park power pedestals work the same way, but I have never looked inside one so I don’t know.  The meter is at the top and the area below it has a top-hinged cover.  Under the cover are three panels about 3″ wide and 15″ tall.  The panels have an outlet towards the bottom and a circuit breaker near the midpoint.  Behind the panels are busses for the hot, neutral and ground with male blade connectors.  The panels have female blade connectors that engage their male counterparts when the panel is slipped and then hinged into place.  It is secured with a single screw.  If Jim L. can find a 50A panel all we will have to do is unscrew and remove the 30A panel and plug in the new one, once we verify that 240 VAC (L1& L2) are present in the box and wired to the distribution busses.

 

Instead of her usual morning walk Linda setup her laptop on the dinette table and worked on accounting and tax issues for Butch and Fonda.  I set my laptop there as well to work on the roster for our FMCA Freethinkers Chapter and Jasper got in between us, so we had a nice, cozy computing session.  When I placed my order with B&H Photo yesterday I checked a box to receive shipping status information via TXT message.  I got one this morning letting me know that my package had shipped from NYC.  Cool.

 

With accounting chores done for now Linda prepared vegan hot dogs with mustard, onion, and relish for lunch.  She then went for a long walk while I stayed at the coach and worked with a new feature on the RVillage website.  I was posting a lot of suggestions to the topic thread on the Ambassador forum and got a phone call from Curtis, the founder/CEO of RVillage.   We had a long chat and I was still on the phone with him when Linda got back.  I worked with the website some more and at 5:00 PM we connected to an Ambassador meeting using GoToMeeting on my computer.  This is a very exciting new feature and I think RVillagers and RV-related businesses are really going to like it once they know about it and see how it works.

 

Linda made mock (vegan) stroganoff for dinner.  She normally uses Basmati but the only rice she had enough of was Texmati so she used that.  Although I did not care for the texture of the Texmati in this dish (a bit crunchy), the taste was still very good.  This dish requires real cooking, which means it makes a real mess.  By the time everything was cleaned up and put away it was 8 PM and we were both tired.  I continued to research engine and transmission gauges while Linda read and played word games.  I also revisited the SonyAlphaRumors website but there was absolutely NO new information on the a99-II.  I went to bed wondering if this camera will ever actually exist.  Based on the comments I see online I am not the only one wondering if this camera will ever be a reality.

One of the hundreds of vendors at the Tyson Wells market area in Q.

One of the hundreds of vendors at the Tyson Wells market area in Q.

 

2015/01/05 (M) VSWR 1.0

Yesterday we finished up the coffees we have been using since we left Michigan at the end of November so this morning I had to open new bags and transfer the contents from their vacuum sealed bags to our metal storage canisters.  I had Teeko’s roast Ethiopian Yirgacheffe regular and decaffeinated separately, so I opened 1/2 pound bags of each.  I also opened a 1/2 pound bag of our special Sweet Seattle Dreams, which is 1/2 Sweet Dreams (decaf) and 1/2 Seattle Blend (regular).  I then made a pot of Ethiopian Yirgacheffe 1/2-n-1/2 while Linda prepared our granola with fresh bananas and fresh blueberries.

 

Linda went for her morning walk while I continued to do online research regarding the enigma known as the Sony a99-II DSLT camera and the supposedly discontinued, but apparently still very much available, Sony alpha a99.  If I did not already have a nice assortment of compatible Minolta A-mount lenses and flash equipment I think I would stop wasting my time with Sony cameras.  But I do, and so I continue to wait and be frustrated along with thousands of other “enthusiast” (sub-professional) photographers.  Because Sony builds the image stabilization (anti-shake) feature into the alpha bodies instead of the A-mount lenses the feature is available even with older Minolta lenses and the new lenses are slightly less complicated and less expensive than the Nikon and Canon lenses, which have the image stabilization built into each lens.  I think this was one of Sony’s best innovations.

 

I also continued to look at automotive gauges and sending units and decided to call Bill Gerrie (in Ontario, Canada) to follow up on his reply to an e-mail I sent a few days ago.  We had a great chat and he was able to clarify some things and add quite a bit of specificity to his written reply.  As a result I have a pretty good idea of what I am looking for; now it’s just a matter of finding it and deciding to place the order.

 

I was starting to work at my computer when Linda returned from her walk.  She eventually fixed a couple of vegan hot dogs wrapped up in tortillas with mustard, onions, and relish.   As I was finishing my meal I got a call from Gary Hatt at BCM.  He recently acquired an Eagle bus conversion and had some questions about the air-conditioners and the Aqua-Hot.  He plans to be in Quartzsite next to week and we are looking forward to finally meeting in person since I have been writing articles for the magazine for almost two years.

 

Linda has been having a problem with the brightness (or lack thereof) of the touch screen on her 19 month old Windows 8.1 Samsung laptop.  It will go very dim for no apparent reason and cannot be adjusted.  There was a driver update available for the Intel HD Graphics processor so we downloaded it, installed it, and re-started her computer.  The screen was now bright, which was more useful than dim, but still not adjustable.  That could be a coincidence or a fix, we will have to wait and see.  Even though it was working (for now) I drove to the local Family Dollar and bought an HDMI cable and some lightly carbonated water.  (The water had nothing to do with Linda’s laptop computer display, we were just low on sparkling water.)  The cable will allow us to connect her computer to one of our two flat panel LCD (LED) TV/monitors if needed.  (We did that after dinner and it worked, mirroring the built-in display to the monitor and setting the resolution to match the monitor’s 1900x1080p native mode.  But it also caused the built-in monitor to dim, although not as much as before.  When we turned off the monitor and unplugged it the built-in display did not return to full brightness.)

 

Mid-afternoon I saw Butch working on his Tarheel screwdriver antenna so I inquired as to what he was doing.  He had connected his MFJ VSWR meter to it through a six foot length of coax.  He had also unplugged the control harness for the tuning motor and rigged up a temporary switch to extend and retract the antenna.  He had done this because he was getting meter readings when connected through the installed coax that indicated the antenna was not resonant at any frequency or that the meter was not working correctly.  I climbed up on his ladder to have a look and saw VSWRs that were often greater than 31:1, and never fell below 10:1, with complex impedances that were rarely 50 ohms and with both resistance and reactance values that were all over the place.  Clearly something was not right.  It was not his installed coax and I was fairly certain I was not his meter, which I had used back at their house to check the VSWR on his CB and 2m ham antennas.

 

I climbed onto the roof of their bus so it would be easier to reach things and I could work sitting down.  We tried adding a ground strap as a counterpoise but it didn’t help.  Butch then grounded the strap to the chassis at the motor but that did not help either.  Our concern was that the antenna was not sufficiently bonded (grounded) to the roof but nothing we tried made any difference.  I decided to set the antenna to its shortest length (highest operating frequency), set the meter to a lower frequency, and then slowly lengthen the antenna, thereby lowering the operating frequency, while looking for some sort of response on the meter.

 

I got no change on the meter and finally realized that the antenna (via the meter) was behaving as though it was not grounded.  I noticed what looked like a thick washer between the SO-239 antenna connector and the base mounting plate of the antenna.  The mounting plate is the ground reference for the antenna and is connected to the base of the antenna through a coil of insulated wire (an inductor) known as a base loading coil.  The spacer was a plastic insulator that was, indeed, preventing the case of the SO-239 antenna socket from making contact with the mounting plate.  As a result the antenna was not grounded through the coax cable shield, preventing the meter from obtaining meaningful readings.

 

We removed the antenna connector, removed the insulated spacer, reassembled the connector to the antenna, reattached the coax and meter, and took additional measurements.  This time we got excellent readings that made very good sense.  We checked the upper bound, lower bound, and the midpoint of most of the high frequency (HF) ham bands and were always able to obtain VSWRs of 1.3:1 or less, which was excellent.  Butch had been considering redoing the mounting of the large motorized fold-over base so it was a good thing we figured this out as it saved him a lot of unnecessary work.  If I can solve one problem without creating others I figure it’s a good day.  BTW:  VSWR stands for Voltage Standing Wave Ratio and 1.0 is not a beta version, it is shorthand for a ratio of one-to-one (1:1), which is the best SWR you can have.  Anything below 1.5:1 is considered excellent, below 2.0:1 good, and below 3.0:1 usable if that’s the best you can do.

 

Chayote is a fruit that is a member of the squash family and is related to other gourds such as melons and cucumbers.  Linda bought one last week when we went to Albertson’s grocery store in Blythe, California and decided to prepare it for dinner tonight.  She sliced it into long thin broad strips and sautéed them with onions, oregano, salt, and pepper.  She served it alongside the leftover mock (vegan) stroganoff with a glass of sangria.  Our wine friends can cringe all they want; we find the Vella and Franzia boxed wines generally agreeable and the sangrias go surprisingly well with a variety of dishes.  And it has me drinking red wine, so it’s healthy too!

 

We lost our WiFi connection this evening.  Not sure why.  The wireless gateway still shows up in the WFR list but won’t associate with the WFR.  Butch had the same problem at the same time so something obviously changed.  We will ask Barb to open the trailer tomorrow, or get Jim to do it if she is not comfortable, so we can reset the gateway.  Hopefully that will do the trick.

The sunsets in Quartzsite are amazing almost every night. This shot was taken from our campsite in Q.

The sunsets in Quartzsite are amazing almost every night. This shot was taken from our campsite in Q.

 

2015/01/06 (T) You’ve Got Mail (Maybe)

 

Our mail situation here is interesting.  Remember that, per our Jamaican tour guide, we do not have problems, only situations, and situations are easier to deal with if I regard them as interesting rather than annoying.  With regards to receiving mail, the “situation” is as follows.  Although every structure in town has a street address—necessary for police, fire, EMS, trash collection, and other municipal services—the Quartzsite post office does not deliver mail to said locations.  They have an annex building on the northeast side of town that is nothing but P. O. boxes and all of the locals, and a lot of seasonal residents (including Joe and Connie, who own the property where we are staying) have a P. O. Box.

 

Where things get interesting is that the main post office and the street addresses are associated with one ZIP code but the P. O. boxes have a different ZIP code.  If something is coming to us via UPS or FEDEX we have to use the street address and associated ZIP code, but if it is being mailed to us USPS we have to use the P. O. Box number and associated ZIP code, or have it sent c/o General Delivery using the main ZIP code.  To confuse matters further, Joe and Connie had to return to Nevada because of Joe’s health and are having their Quartzsite mail forwarded back to their home, so we cannot have mail sent to us “care of” them as we originally planned as it just gets forwarded to Nevada.  Outbound mail does not appear to be a problem, but then why would it be?

 

The other situation that developed yesterday was that our WiFiRanger Mobile Ti disconnected from Joe and Connie’s WiFi (DSL) gateway and would not reconnect.  The WFR is telling us that the WPA password may be incorrect, but that is unlikely as we have been using it since we arrived last month, as have Butch and Fonda who also lost their connection yesterday and could not reestablish it.  The evidence suggests that the gateway needs to be reset.  Why?  Who knows?  DSL gremlins perhaps.  Or mischievous Internet fairies.  Or a problem with the local DSL service?  Or perhaps Butch keyed up his 600 Watt linear HF ham radio amplifier and blew out every wireless DSL router within a quarter mile?  Whatever the cause, once we can get Barb or (brother) Jim to open the trailer we will power cycle the gateway and see if that restores our ability to connect to it.

 

In the meantime, in order to get online last night and again this morning, we turned on our Verizon MiFi.  The Verizon signal here is strong and steady, and the data rate is much faster than the DSL/WiFi connection, but we only have a 4 GB data plan so we tend to use WiFi when available.  It is not always available, of course, especially while traveling (and especially if we are boondocking at Wally World or other such locations) and when it is available it is not always reliable or is so slow as to be useless.  This can be the situation, for instance, at larger RV rallies and even some RV parks.

 

So we logged into our Verizon Wireless account, looked at our current plan, and saw that for a mere $10 more per month we could increase our data plan from 4 GB to 10 GB.  The cost for exceeding your monthly data plan limit is $15/GB, so the extra $10/month was a no-brainer.  And VZW made it soooo easy to change our plan (once we were logged in); just click the data plan we want, review changes to our account, and click “Apply Changes.”  Done; they have our money and we have more data allocation.  Interestingly, they upped our data allocation immediately for the current billing cycle, which is Dec 20 – Jan 19, and added the $10 to the bill we will receive for that cycle.  No pro-rating going on here, but then we can use the whole 10 GB if we want/need to.

 

Interestingly the cost to go from 10 GB to 15 GB was an additional $20/month, so the 10 GB plan seems to be a sweet spot after which you pay a premium for additional access.  On the one hand Verizon wants to sell you data bandwidth but on the other hand there is a finite amount of data they can move through their network, so if you want to use a larger chunk of their capacity it figures that it would come with premium pricing.

 

Until a few months ago Millenicom was reselling 20 GB MiFi plans (on Verizon’s network) for $70.  It was the best deal around; a sufficient amount of data for the same price we were paying Verizon for only 4 GB.  Kind of unfair, when I think about it.  Well, Verizon decided to stop selling bulk capacity to Millenicom (and other MVNAs?), took all of the accounts in-house, and Millenicom went out of business.  Not really a big surprise when you think about it.  Verizon also notified those customers (as I understand the situation) of their “options” which were not, apparently, as attractive as the deal they had with Millenicom.  Not really a big surprise when you think about it.

 

Anyway, we will see how we do with 10 GB/month while we are on the road.  We can change back to our 4GB plan when we get home, but I doubt that we will, and we can increase it to 15, 20, or even more GB per billing cycle if we need to, but that is unlikely.  We have an AT&T landline at home with DSL service that provides an “always on” Internet connection (when it works).  It has a 150 GB/month data allowance and allows us to monitor and control our whole house generator and WiFi thermostat.  We have discussed adding a security system and a personal weather station linked in to Weather Underground’s Wundermap when we get home.  I don’t think our DSL connection is fast enough, however, that we could use 150 GB in a month if we tried.

 

Linda went for her morning walk and I made a quick run to Barry’s Breads.  Barry is a really nice older gentleman who has a small bakery stand on the north side of Kuehn Street east of Central Avenue.  Just behind the stand, however, is a larger trailer in which he bakes all of his products.  Those products include breads, rolls, savory items, and sweet goods.  Most of his products use butter, cream cheese, cheddar cheese, or ranch dressing, but his Basic Bread is just that, flour, water, sugar, salt, and yeast.  I have had some difficulty figuring out what time of day to stop by but this morning he finally had loaves of bread, and some hamburger buns made from the same recipe, so I bought a loaf and a pack of four buns.

 

When I got back I started working on another article for Bus Conversion Magazine.  A little over a year ago I installed an RV-Critter Guard to seal around the shorepower cord and water hose where they enter the utility bay through the floor.  I took a few pictures during the installation and have had the article on my “future” list ever since.  By the time Linda got back from her walk I had the article mostly finished and was starting to look at the photographs.

 

She had stopped at the Salvation Army store, which was open, to use their facilities and ended up buying a grocery bag full of clothes for $1.  Not $1/item, $1 for the entire bag.  Most of the items were tagged with color codes indicating prices of one or more dollars each but they had too much inventory and needed to move some product.  They told Linda that when that happens they have their $1 bag sale.  Deal.  She called Butch and Fonda to let them know and I think they headed there before going to check the post office box and then stop at the post office if needed.

 

Linda cooked a couple of our Boca vegan mock hamburger patties and served them with fresh sliced onion, lettuce, and pickles on two of the buns I had just purchased.  Not an entirely WFPB meal, but very few of our meals are.  Still, we try to get as much plant-based whole foods as we can every day.

 

Linda went for a second walk after lunch and headed down Central Avenue towards the Kuehn Street markets.  She is so fond of her 5.5″ Hammer Stahl Santoku knife that she wanted to buy the 3.5″ paring knife if Cutlery by LeClaire had it for sale as an individual item.

 

While Linda was gone I finished working on the photos for my RV-Critter Guard article.  When she returned from her walk she had both the Hammer Stahl 3.5″ Paring Knife AND the 3.0″ Birdsbeak Paring Knife.  As we learned the other day from an Alton Brown video paring is actually a technique in which food is held in one hand and a knife in the other; no cutting board is involved.  Paring knives are generally smaller with a shorter blade and most of the weight is in the handle, allowing very fine control of the cutting edge and tip.

 

The Birdsbeak is a particularly interesting and unusual knife.  The bottom/cutting edge is slightly concave rather than convex like the classic chef knife.  The bottom edge joins the top edge in a point with a shape that resembles certain types of curved bird beaks.  In use, the knife is often held stationary and the food is pressed or turned into it, such as decorative peeling, pitting of fruit, or slicing strawberries.  Linda is often reluctant to spend money on herself so I think it’s nice that she found something she wanted and made the decision to buy it.  Like any high quality tool it will make the work it is designed to do easier and more enjoyable.

 

While I was uploading my article to our Dropbox Linda went outside to sit.  Barb wandered over and I mentioned that the DSL wireless Internet gateway had quit working.  She let me in the trailer where I found it sitting on the dining room table.  I powered it off, waited 60 seconds, and powered it back on.  All of the status lights came back on in the expected sequence and I was once again able to connect our WiFiRanger Mobile Ti to it.  We ended up standing by their Country Coach Intrigue motorhome and having a long chat.

 

Butch and Fonda were gone for most of the afternoon so we only got to chat for a little while when they returned before the sun dropped behind the southwestern mountains and the temperature dropped along with it.  Linda and I talked about going out to dinner, which we have only done once since we got here, but she remembered that we had a FedEx package scheduled for delivery today and that it might arrive as late as 8 PM.  So we had leftover soup with crackers and sangria.  This was the third and final meal we got out of this pot of soup and it was good to the last drop.  It was a packaged mix but Linda thinks she can recreate it; getting the spices right will be the tricky part.

 

After dinner I read DSLR reviews on the Digital Photography Reviews website and continued to look at gauges and sending units for the bus.  Around 8:30 PM I was having trouble staying awake but by 9 PM I had gotten my second wind and decided to write another short article for BCM.  This one was on the failure of Butch and Fonda’s main engine air-compressor on the drive down, how he dealt with it on the road, and eventually ended up installing a rebuilt one here at our campsite in Quartzsite.  I had the article written by 11 PM and decided to work on the photos tomorrow.

Sunset envelopes our coach as Linda prepares dinner.

Sunset envelopes our coach as Linda prepares dinner.

 

2015/01/07 (W) Catch 22

 

My main pair of reading glasses broke yesterday; not the lenses or the frame, but one of the nose pads.  Well, not the actual pad, but the small plate and mounting loop, specifically the mounting loop.  I was cleaning them and the whole assembly fell out.  The loop was split and had opened up.  The loop was a very small and delicate piece of ductile metal so I squeezed it back into a circle.  I removed the very tiny retaining screw, reinserted the mounting loop, and put the screw back in.  I was able to do this using only the tools available on my Leatherman.  The repair did not hold and it fell out again last night.  This time a piece of the loop broke off so the only repair will be a new mounting pad if I can find one.  There is a Wal-Mart in Parker that probably has an optical shop but I don’t know how universal this mounting system is.

 

I checked the level of the floor and counter in the kitchen last night and the coach appears to have settled slightly on the driver side.  Not a lot, but enough that I can feel it and it registers on the level.  I generally have to start the main engine and build up full air pressure in order to level the coach but I thought today would be a good day to finally pull the portable air compressor out of the car and see if the leveling system will work without the main engine running.  As it turned out that did not happen today because we ended up driving to Parker, Arizona.

 

Our destination in Parker was the Wal-Mart.  The store did not have an optical department but we found an eyeglass repair kit in the pharmacy area with a pair of screw-in pads and a pair of snap-in pads.  They also had a repair kit with a tiny screwdriver, spare screws, and other parts.  Between the two kits I was able to install a new pad in the car to replace the broken one.  That saved us a trip the optical shop in town.

 

Parker sits on the Arizona side of the Colorado River which is the boundary with California.  We decided to drive across and then take CA-62 over to US-95, follow it south along the River back down to Blythe, and then take I-10 back to Quartzsite.  Butch called while we were in Parker to let us know that there was a Farmer’s market at Desert Gardens.  It operates on Wednesdays from 8 AM to noon so we did not make it back in time but resolved to go in future weeks.

 

I worked on my “roadside repair” article for BCM while Linda went for a walk.  Jim and Barb had gone to Blythe to buy a new faucet and Jim L. stopped by and helped Jim B. install it.  They borrowed a caulk gun from us (we carry two in the bay) but had to go buy caulk.  UPS showed up with yet another package for us, after which we had a long conversation about the inadequacies (incompetence) of the U. S. Post Office in Quartzsite.  (The UPS driver told me that both UPS and FedEx have extra drivers and trucks delivering into Quartzsite during the peak season.  What a novel idea.)

 

Back to the post office.  We are waiting for a shipment of two bottles of water hardness test strips that we ordered through Amazon but were shipped via USPS by a swimming pool supply company in Elkhart, Indiana.  I gave them the P. O. Box here in Q since the post office does not deliver mail to street addresses and it appears that they will likely get returned to the sender rather than delivered to us.  The root cause of the problem (and it is a problem) is that Joe and Connie are having their mail forwarded to their home in Nevada.  If their names are not on the mail the post office won’t put it in the box, but if their names are on the mail it still does not get put in the box, it gets sent to Nevada.  So as of now the box is sitting there but cannot be used; a genuine “catch 22.”

 

Fine, we will just use General Delivery.  The problem with that (and it is a problem) is that you can only pick up the GD Mail at the Quartzsite post office between 11AM and 1 PM, and there are untold numbers of people trying to do the same thing.  That means ridiculously long lines and ridiculously long waits.  Considering that the influx of seasonal “residents” to Quartzsite has been going on for over 30 years the postal “service” has had ample time to figure out how to handle the situation.  I mean, Amazon practically runs its holiday operations with seasonal employees, many of whom are RVers.  Gee, I wonder if there are any RVers around Quartzsite this time of year.  While the post office is trying to figure out how to not deliver our mail we have two more UPS shipments scheduled to arrive on Friday.

 

Linda made a zoodle dish for dinner.  She used her SpiraLife to turn a zucchini into long thin strips which she cut into 6″ lengths and then used like spaghetti in the dish.  The other ingredients were onions, garlic, mushrooms, asparagus, and green beans.  Everything got sautéed in a pan with a little olive oil, salt, and pepper.  We had a glass of Lamb’s Valley Organic Sweet White wine and it was a lovely meal.

 

After dinner I put the finishing touches on my BCM air-compressor repair article and e-mailed it to Butch to proof-read.  The only thing worse than writing an article that makes me look stupid is writing one that makes someone else look stupid, especially a friend.

 

I had an e-mail from Gary, the publisher of BCM, letting me know that the December 2014 issue was finally available online.  I downloaded both the SD and the HD versions.  I then clipped the cover from the SD version, pasted it into MS Paint, and saved it as a JPEG file.  I opened it in Faststone Image Viewer, resized it to a thumbnail, and sharpened it.  I then edited the BCM page on our website, adding the thumbnail image, the title of my article, and a brief description.  I have a similar entry on that page for every issue in which I gave had an article, starting with the February 2013 issue. The December 2014 article was my 14th in 23 months.

The last glow of this sunset reflects off the passenger side of our motorcoach in Quartzsite, AZ.

The last glow of this sunset reflects off the passenger side of our motorcoach in Quartzsite, AZ.