Our day started, as it usually does, with coffee and breakfast.  When we finally got to work on our tasks for the day we started by putting various things in the house back where they belonged, many of them having been piled on beds or put in uncarpeted areas while Jack cleaned the carpets on Wednesday.  Linda settled in at her desk to deal with paperwork while I got out our Honda self-propelled lawn mower and finished cutting the grass around the house.  She then turned her attention to straightening up the house and cleaning the kitchen in anticipation of tomorrow’s dinner guests.

I puttered in the bus for a bit trying to figure out how the cabinet above the refrigerator was constructed and might, therefore, be deconstructed but did not solve that puzzle and turned my attention to our Cub Cadet 1000 Series (LT1040) lawn tractor.  The mower deck is badly out of adjustment, sitting very low on the right side even with the height adjustment lever in the highest position.  I wanted to remove it rather than try to adjust it so I could use the tractor to more easily tow the new utility cart around the yard.

I already had the PDF version of the manual on my iPad and studied the directions for removing the mower deck.  It appeared to be an easy procedure that could be done by one person but I had Linda help me.  Once it was out from under the tractor we cleaned it off as best we could.  It had what looked like many years of grass clippings packed into every nook and cranny.  One of the idler pulleys was broken, a wheel was loose and its bracket slightly bent, and the drive belt was in very bad shape.  If we ever want to use it again those things will have to be replaced and repaired.  The suspension mechanism on the tractor will also have to be adjusted.

The tractor is leaking something, either oil or hydraulic fluid, so now that the mower deck is out of the way I will try to identify the location of the leak.  The tractor came with the house when we bought it so it was “free” (in a sense).  It was not in the best of shape, so there is a limit to how much time, effort, and money we will put in to fixing it.  Besides, for now Keith mows the grass and we have the self-propelled Honda walk-behind mower for trimming up the yard, if needed, between major cuttings.

My next task was to get the trailer ball off of the back of the lawn tractor.  The ball had a 2-1/8″ hex base flange and the nut was 1-1/8″.  I did not have a 1-1/8″ socket or a 2-1/8″ open end wrench, so I went to Lowe’s in search of said items.  I found a deep 1-1/8″ impact socket with a 1/2″ drive but they did not have open end wrenches the size I needed so I bought a very large slip wrench.

The nut was initially coming off easily but then bound up.  Even with Linda’s help we could not turn it.  We own a torque wrench that is over 3′ long and will work up to ~800 lb-ft of torque, but it has a 3/4″ drive.  So we went back to Lowe’s to get a 1-1/8″, 3/4″ drive socket.  Fortunately they had one.  While we were there we also bought a 6 gallon pancake style Porter Cable air compressor and a new American Standard toilet seat for the upstairs hall bathroom.  The air compressor is smaller than the 15 gal Dewalt and may fit in the passenger side engine bay.  It has regulated output pressure to 150 PSI so it should be sufficient for inflating the front bus tires.  The toilet seat was the right shape but the wrong color, so it will get returned.

The torque wrench gave us enough leverage to move the nut a bit more but then it bound up again.  I suspect the threads are mangled.  We sprayed some WD-40 on it but it did not help.  I called Butch to see what suggestions he might have.  Heating it might help but I do not have anything that would get it hot enough fast enough.  Plus, the ball/nut are just below and behind the plastic gas tank; not a good place for intense heat.  Butch has an induction heater that would be ideal for this situation, but it is five hours away in north central Indiana.  I asked about a nut splitter but Butch said he has not had much luck with those.  He suggested a large pipe wrench.  They are self-tightening (when used correctly) and could grip the ball directly if needed.  I do not plan to reuse the ball so I do not care if it gets mangled, I just want it off the tractor.  If all else fails Butch said I can cut off the bolt with my Sawzall reciprocating saw.

I had planned to work on computer-based tasks today but was not in the humor by the time I was done working on physical tasks.  Linda made fajitas with sautéed onions and bell peppers, vegan gyro “meat”, and vegan sour cream.  Yum; that’s a keeper.