Category Archives: CB-MEF

20240826-27_Tenor-Clock_MEF2

Leave a reply

NOTE:  There are four (4) photos, with captions, in this moderate length post.

 

Monday 26 & Tuesday 27 August 2024 — Clocks, tanks, colors, and furniture

 

Monday 26 … It’s about time (clocks and septic tanks)

Glenn Williams, the owner of Tenor Clock, arrived right at the appointed time and carefully carried the mechanism for our grand-father clock in from his car.  He explained what he had to do to clean and repair it.  Besides cleaning off the oil that I had incorrectly applied to gears and some other parts, he replaced quite a few tiny (sleeve) bearings.  He had the mechanism mounted on a stand in his home workshop and had adjusted the pendulum to keep time.  He also adjusted the winding mechanisms for the three weights so that I could not overwind them and cause them to jam.  He then set to work re-installing it in the case.  Once mounted, with the pendulum and weights hung, he made fine adjustments to the clock hands and to the strikers for the chimes to get them to sound just right.  (It’s a Westminster Chimes set.)  The chimes now sound precisely at the quarter hours as they should and sound wonderful.  True to his original estimate, it had taken about two (2) months for him to fit this into his work flow.  We were happy to wait, but equally glad to have the clock back in working order.

Sometime during the day, I called Ewers Septic Service to arrange the pump-out of our two septic tanks.  Based on my last conversation with Phil Jarrell, our driveway/septic/foundation/grading contractor, I knew we were overdue to have this done.  The women I spoke to at Ewers reinforced that we were waaaay overdue.  I promised to do better in the future.

 

Tuesday 27 … A visit with our interior design consultant (daughter); staging a furniture donation for the local HfH ReStore

Our daughter (Meghan) came over during the morning and spent several hours helping us with interior design issues.  She has done a lot of remodeling on their house, and well-acquainted with many websites for design ideas, materials, furniture, lighting, and appliances.

Top of the list was choosing a color (stain) for our red oak floors.  We want them stained darker, but not too dark, but figuring out the correct tone/tint (warm, neutral, cold) relative to our existing hickory cabinets was proving to be a challenge.  Added to the mix was that we would be getting new dining room furniture and were trying to arrive at a style, shape, material, and color that would work well with the existing kitchen cabinets, appliances, and refinished floor.  Here is what we were considering:

Existing floor (red oak) and kitchen cabinet (hickory) framed by dishwasher (white, left) and range (white, right) with the floor sample we like (dark, large, Superior Red Oak with Praline finish) from Michigan Hardwood Distributor) and the table wood (hard Maple) and finish (not sure of the name) we are considering.

BdW guest Bonnie & Randy D were scheduled to leave tomorrow but left today instead.  They had found a buyer for their motorhome and today was the handover to the new owner.  This was set to take place at a credit union in Brighton, where money, title, and keys would be exchanged.  They would then check-in to a suites motel in town for about a week until the closing date for the house they had purchased.  For most of the time there were staying on our property they were cleaning out the MH and moving their possessions into a storage locker in town.  Their activities were never intrusive, even the day the RV inspector was here (most of the day), and we were glad that they stay worked out well for them.

Tuesday is grass-mowing day so, as usual, Keith was here.

After Meghan left, I moved the F-150 out of the large bay of the garage to make room for the dining room furniture we were donating to the Habitat for Humanity (HfH) ReStore nearby.  The buffet/China cabinet was especially difficult to move.  Even with the drawers and custom glass top removed it was still heavy and awkward to handle.  But we got it done as shown in the following photo:

The DR buffet/China cabinet and drawers in the garage, waiting to be picked up by the local HfH ReStore.  The DR table and chairs have yet to be moved to the garage.

 

With the Bassett DR furniture moved to the garage, we set up our folding card table and brought up the three folding chairs (with padded seats) from the basement.  Linda is seated at the table, which is not directly under the pendant light, as we think the proper location for the new table will be slightly to the left (north) of the existing light fixture.  Here’s a photo:

The dining room area looks very spacious without its usual furniture, but it is not that large of a space and we will have to be very thoughtful about what we put in here next in order to ensure good traffic flow with adequate clearance around the DR table.  The DR table sits at the intersection of the kitchen (with its door from the library/garage), doorwall to the deck, Linda’s desk (to the left of the refrigerator) and the hallway/foyer (to the bedrooms, and front door / basement stairs, and living room).

Here’s another photo over the color and wood grain palette we are considering:

Existing red oak floor, proposed floor color (large, dark sample of Superior Red Oak with Praline finish), proposed DR table sample (hard maple /warm brown) and fan-pack of stain sample photos on red oak.

…

20240801-04_A busy-start-to-August

Leave a reply

NOTE:  This is a moderate length post (for me).  It has two (2) photos with captions, both taken by me (Bruce) with a Google Pixel 6 Pro.

 

THURSDAY 01 thru SUNDAY 04 August 2024 — Heat, rain, mosquitoes, and a busy week (BdW guests, laundry appliances, dogs, glasses, finances, and more) but no more yard work

 

Thursday 01 August … New glasses, a dead battery, more work tables, and Wild Turkeys in a tree

I got a text message yesterday that my new/remade tri-focal glasses were ready, so we made a trip to the Brighton SVS Vision Center to pick them up.  But not in the F-150.  When I tried to start it, the battery was completely dead.  It turned out that the headlight switch had been moved from the AUTO position to the Running Lights position, and left that way overnight.  Mea culpa, and I should have known, but I ignored the chime that continued when I turned off the engine last night and removed the key.  Dumb.  We took Linda’s car instead.

My new tri-focal glasses were correct this time, improving my distance vision just enough to make road signs at various distances sharper.  The reading and middle portions of the lenses were the same as before.  The optician made adjustments to the ear hooks and the nose pads until they sat correctly on my face with its slightly askew nose, which was broken many, many years ago.  I also had her look at my reading glasses.  I got the lenses there a month or so ago, but had them use an existing frame that I liked.  One of the ear covers had cracked and separated into two pieces.  She was able to heat them both up (left and right, one at a time) to remove them and replace them with new ones.  She also noticed that the nose pads were cracked and needed to be replaced, so she did that as well.  She then adjusted the ear hooks and nose pads so they sat correctly on my slightly crooked face.  No charge for the extra services.

Back home, we stopped at the barn and I retrieved a battery charger and a set of jumper cables.  The truck was in the garage.  The engine compartment is “tall”, so I placed the battery charger on the fold out platform of a 6 ft stepladder.  This allowed the battery cables to reach the battery in the engine compartment and the power cord to reach a nearby ceiling outlet.  I connected the cables, plugged in the power cord, and set the operating parameters:  AGM, 25 Amps.  The display quickly ramped up to 25.8 Amps and stayed there.  That was good news; some battery chargers will not work unless they detect at least some minimum voltage level from the battery.  I am hopeful that the battery will recover; it’s only a few years old had never been abused prior to this accidental discharge.

The bottom end of one of the Rockler Rock-Steady 32” legs with the adjustable foot installed, but not adjusted or tightened.

The Rock-Steady leg is a simple, but cleaver, design.  A flat sheet of steel is machined with various openings, both round and square, to allow other components to be attached, either with machine screws/bolts, or with carriage bolts.  The bottom end is partially slit at the mid-point to form two tabs, one slightly longer than the other.  The tabs are then bent 90 degrees, shorter one first and then the longer one.  The entire sheet is then folded along its midline, forming an angle iron, with the tabs overlapping.  The overlapping tabs are drilled to accept the adjustable feet, and the whole piece is then power-coated.

I changed into my work clothes and headed to the barn to assemble the last (for now) Rockler Rock-Steady Work Table.  I attached this one to the table along the south wall of the shop that was already attached to the Corner Table in the SE corner of the shop.  In this configuration, I will have a work surface along the south wall of the shop that is at least 20” deep and 144” (12’) long.  It will end just shy of the “protected” (no storage allowed) area in front of the shop/storeroom electrical sub-panel.  A picture will make this much clearer.

The workshop (in the barn) as seen from the entry door looking east.  The Corner Stand to the left (NE corner of the shop) has two Rock-Steady Work Stands attached.  The Corner Stand to the right (SE corner of the shop) also has two Rock-Steady Work Stands attached, plus a third Rock-Steady Work Stand along the wall on the right, which is attached to the one from the Corner Stand.

It was warm in the shop, even with a box fan running, so I got a bit sweaty and took a shower before dinner.  Having only had a muffin for breakfast, and skipping lunch, Linda made a large salad and we had an early dinner around 4 PM.

As we were eating, Linda noticed a lone Wild Turkey resting at the base on one of our large White Pine trees to the east of the valley for our walk-out basement door.  We thought that was odd, but it seemed to be okay.  As we were clearing the table, I saw a small turkey (jake) drop out of the tree, and then another one.  I called Linda over, and we watched the entire flock, including the other adult, drift down out of the tree.  So, it wasn’t a lone turkey after all; it was our usual flock of 10.  It was the second time this week that I had seen them in a tree, and the first for Linda.

 

Friday 02 August … Boondockers, bus chat, and financial chat

Rick (BdW PeachyTravel) was out this morning with their dog, Barkley, and we had a nice chat.  They pulled out before I left to meet Chuck S. at 11:30 AM for lunch at Leo’s Coney Island in S. Lyon.

Chuck and I had a lot to catch up on, and occupied a booth for three (3) hours!  The restaurant was busiest from noon to 1 PM, but had open seats the whole time there, and no one suggested we should move on.  It rained off and on while driving there, while we visited, and on the drive home.  By 5 PM we had a lot of standing water in the usual low spots around our property.

During the afternoon, I got a call from Kishen, one of our financial advisors at Stifel-Nicolaus.  We had a nice chat and made an investment decision.  We have been 100% satisfied with this company and the specific team of people we work with directly.  Sometime during the day, Linda also talked to Nan (of Paul & Nancy) regarding the cruise we are all taking in early December.

BdW guest Marcia B was supposed to arrive today for a 2-night stay, but cancelled last night.  It happens, and cancelations are never a problem for us as long as we know.  We are also RVers, and we understand that things can happen, even at the last minute, that change travel plans.

 

Saturday 03 August … A birthday and party planning

Today was our son’s 46th birthday (1978).  Linda wanted to have the family over to celebrate, but today was not convenient, so it was set up for tomorrow.   I do not recall what I did today, but it probably included a trip to Recycle Livingston to get rid of our household recyclables, doing laundry, and working at my desk.  The mosquitos have been very bad, so we have temporarily eschewed working on the property.  Linda spent a good part of the day preparing for the family get-together.  That included cleaning the house, a trip to the grocery store, and preparing food.  At some point, I brought chairs up from the basement and we put the expansion leaf in the dining room table.

 

Sunday 04 August …  A family gathering and a birthday celebration

Linda arranged a family gathering for today at our house to celebrate our son’s birthday.  Brendan was there (of course) with his daughters (Sadie and Madeline) and our daughter, Meghan, was there with her husband, Chris.  Brendan’s wife, Shawna, whose birthday was in 11 more days, had previously made plans to go out of town for a weekend with her girlfriends.  She was missed, but everyone still enjoyed themselves.  Our daughter made a vegan peanut-butter chocolate cake for dessert; vegan for us and peanut-butter/chocolate for her brother.  It was amazing.

When everyone had left, we just relaxed.  In the evening, we continued watching the NBC recap of the Paris 2024 Olympics.

…

20240717-18_Construction_&_Deconstruction

Leave a reply

NOTE:  This longer post does not have any photos.

 

WEDNESDAY 17 and THURSDAY 18 July 2024 — Dental, walking, mowing, and a global IT outage

 

Wednesday 17 … Highway construction, a motorcade, and dental deconstruction

I had an appointment late morning with our dentist to deal with the right rear-most, lower tooth that had lost its partial crown about two (2) weeks ago.  In all the time we have lived in Michigan (since 1976) I have never seen so much road construction as we have at the moment, so I left early to make sure I wasn’t late.  Major highways are being widened all over SE lower Michigan, and flex-lanes are being added or extended on the highways to run through our local community area.  The amount of equipment I passed today on I-96 was epic.  At one point there were 12 gravel haulers lined up nose-to-tail waiting their turn to dump their loads.  There were two concrete forming machines in operation, several very large cranes, and all sorts of excavators, cutters, rollers, concrete mixers.  My best guess was at least 50 pieces of heavy equipment, much of it specialized to road construction.  It was fascinating to see and, fortunately, there were no major traffic backups.

Close to the clinic, I headed west on Michigan Avenue to make the U-turn (Michigan left) back to the clinic.  I noticed a LOT of flashing emergency lights, and not long after pulling into the U-turn, a motorcade went by (westbound) probably headed to the Detroit (Wayne County) Metropolitan Airport.  I later learned that the motorcade was transporting Vice-President Kamal Harris following a speaking engagement in Detroit.

At the clinic, the dentist made an adjustment to one of my night-time bight guards and then got to work on my tooth.  He decided to remove some of the existing tooth to allow the new crown to be thicker on top (that’s were the old one failed) and to come down around the tooth closer to the gum line for a more secure fitment.  With the tooth prepared, he used the photo/laser scanning system to “map” the inside of my mouth on my right side.  The scans included the upper and lower teeth (mouth open) and the outside of the teeth in the closed position.  The new crown will be ceramic (Zirconia) and should be ready in about two weeks.

The dental assistant fitted a temporary crown, which was quite a procedure in its own right.  It will protect the tooth until I get the permanent crown, but I was advised to still chew on the left side and avoid hard, crunchy, and gooey/sticky foods.  Before leaving the clinic, I made an appointment for August 8th to have the new crown fitted.  The tooth is still “sensitive” when touched in certain ways, so I suspect the temporary crown does not completely protect the lower back side.

 

Thursday 18 … Walking, mowing, and seeing what’s behind you; and a major computer outage!

Linda met up with our daughter around 9:30 AM to walk a portion or the Mike Levine Lakelands Trail.  From the Michigan History Center (Michigan.gov):  “The Trail runs 33 miles between Hamburg Township in Livingston County (US-23 and M-36) and Blackman Township in Jackson County (near Stockbridge). Opened to the public in 1994 as the Lakelands Trail State Park, it is a popular destination for people looking to enjoy the outdoors. The trail is also a component of the Great Lake to Lakes Trails Route #1, which extends 275 miles from South Haven (Lake Michigan) to Port Huron (Lake Huron). Local philanthropist, Mike Levine, contributed extensive resources to transform the corridor into an improved trail. In 2018, the DNR changed the trail’s name to the Mike Levine Lakelands Trail State Park in recognition of Mike’s efforts.”

Our property was not completely dry after the rains last night, but I wanted to get the grass cut sooner rather than later so it had time to grow before next Tuesday when Keith would once again be here.  I had the lawn tractor out of the shed and ready to go by 10 PM.  I decided to set the mowing deck at its highest setting, so the grass would be long enough by next Tuesday to make it worth having Keith show up.  I decided to cut the grass on the west half of the property on a SE-NW diagonal and the grass on the east half of the property on a SW-NE diagonal.  On the west side, that meant I was cutting across the old furrows left over from when this property was part of farm (many, many years ago).  The lawn tractor does not have a suspension, so I got beat up today.  Keith usually mows on an E-W orientation, which makes for a smoother experience.  Both he and I have to deviate from that, of course, to go around trees, stumps, buildings, the firepit, and along the edges of driveway as well as stands of trees and bushes.  But that was the general idea for today.  I worked until 1600, with a 30-minute break for lunch around 12:30.  I was tired, but it felt good to have this done.

Linda got home around 1300 and had a bite of lunch.  She took her car to Serra Honda for a 14:30 appointment to have the glass portion of the driver-side rearview mirror replaced.  The labor was more than the part, but it required some special tools and knowledge to remove the old one without breaking plastic retaining tangs or the housing.  Besides, if the technician dropped the new mirror, it would be at the dealer’s expense, not ours.

Sometime during the day, or perhaps it was overnight last night, an update of the CrowdStrike security software was pushed to their clients with a bug in it that caused a world-wide outage of computers running the Windows operating system, including Windows Server and Windows Enterprise.  The event was well-covered in the media, so I don’t need to repeat it here.  We were not doing anything at the time that might have been impacted, so for us it was just an interesting and curious news story.  But for many people, especially those traveling, and for many (most?) of the really big corporations around the world, and even governments, it was a major disruptive event.

…

20240624-30_Summer-is-here_work-continues

Leave a reply

NOTE:  This is a short post that includes one (1) photo with caption, taken by me (Bruce) with a Google Pixel 6 Pro.

 

MONDAY 24 thru SUNDAY 30 June 2024 — Summer is here, BW guests, and a birthday brunch

 

Monday 24 …  Property maintenance

Nothing noted on our calendar.  Linda was still in Dexter cat-sitting.  I’m not sure what I did, but I might have spent part of the day pruning trees.  I microwaved something for dinner.

 

Tuesday 25 … Wet weather, inside work

We had heavy rain this morning, so I had Keith skip the mowing today.  It was unlikely that I worked outside, so it must have been an inside day.  That usually means I worked at my desk, either cleaning up e-mails, backing up files, working on blog posts.  I microwaved something for dinner, again.

 

Wednesday 26 … Another BdW guest arrives

Boondockers Welcome (BdW) guests Elizabeth G. and spouse arrived around 1 PM for a 1-night stay.  As usual, I met them in the street and got them situated in our guest site.  We visited briefly, and then I left them alone to set up their rig and do whatever else then needed to do.  Linda was still in Dexter cat-sitting, and I have no idea what I did the rest of the day other than microwave something for dinner.  I know it sounds like “Groundhog Day” all over again, but it really wasn’t that repetitious.  I had a nice selection of vegan microwaveable meals to choose from.

 

Thursday 27 … Medical follow-up, and a return home

Our BdW guests pulled out sometime before noon.  Meghan and Chris returned home from the trip to Las Vegas and were very happy to see their kitty cats. Linda had a 4 PM phone follow-up with UofMH KEC Ophthalmology, which she might have done from her car while driving home.

 

Friday 28 … Another BdW guest arrives

ABIR, we had an easy day of it today.  Linda had been away from the house for a week, and was ready to just settle back in to our normal routine.  BdW members Wjrdmr945 arrived mid-afternoon for a 2-night stay.

 

Saturday 29 … A Mead tasting opportunity

We received an e-mail from Schramm’s Mead announcing tasting opportunities at their meadery in Ferndale, Michigan.  Various dates were available with specific time slots for each.  A reservation and pre-payment were required.  I signed us up for Friday, July 5 at 1 PM.  The tasting included six (6) different meads for $25 per person.  Tasting of their very best (and rare) meads was available for considerable added cost, but we have had those meads, and were more interested in developing a broader understanding and appreciation of their range of products.

 

Sunday 30 … Happy Birthday Linda!!!

Our daughter invited everyone (us and her brother’s family) to The Lake House for brunch to celebrate Linda’s birthday.  She’s not bashful about her age, but I will leave the specifics for those who have a need to know.

Meghan made two different kinds of really excellent vegan French Toast, one using cinnamon raisin bread.  She also cooked up a batch of vegan sausage patties along with actual bacon.  There was (real) maple syrup (of course), plant-based as well as dairy butter, and a mixed fruit salad with CocoWhip (a vegan replacement for whipped cream).  Oh, my goodness, what a nice meal.

Brendan & Shawna gave Linda a bottle of white port.  They did not bring it home from Portugal (too difficult to transport) but they tasted quite a bit of port while they were there, and discovered white port as a result.

Sadie ended up at the beach playing in the water (just her lower legs, it was a cool day) and “digging a tunnel to China” in the beach sand.  Uncle Chris helped her with the tunnel.  All-in-all, we had a nice long visit with family.

We had not planned anything else for Linda’s birthday, but it didn’t seem right for her to have to fix dinner.  I had planned on cooking, so we decided to go to the local Olive Garden restaurant for dinner.  It was just okay, but we didn’t expect it to be outstanding, so we were not disappointed.

Back home, we had some of the white port.  It was very sweet, but quite good, and we both enjoyed it.

A view of the outside of the new garage doors.  It’s placed here because this is the date when I took the photograph.

…

20240622-23_state-finals_cat-sitting_workbenches

Leave a reply

NOTE:  This is post includes three (3) photos with caption, taken by me (Bruce) with a Google Pixel 6 Pro.

 

SATURDAY 22 and SUNDAY 23 June 2024 — A state finals, a trip (not us), cat sitting, and shop work stand assembly

 

Saturday 22 …  A state championship, a trip to Las Vegas (not us), cat sitting, shop cleaning, work stands

The NE corner of the shop room in the barn cleared out to make room for one of the two Rockler Rock-Steady Corner Stands.  I ordered two of these, along with five (5) Work Stands, each 56” L x 20” D x 32” H.  The 20” depth matches the depth of the two “ends” of the Corner Stand so they can be connected together using special double-ended bolts with a space section in the middle.  I bought enough of these connectors to connect a table to each side of both corner units, plus a 5th table to end of one of the work tables.

Our daughter, Meghan, had been providing child-supervision and entertainment for her niece (Sadie) since Tuesday, but needed to hand those duties back to Linda as she had a state championship Quiz Bowl tournament this evening in the state capital city of Lansing.  Also, she and Chris were leaving tomorrow for a week in Las Vegas.  Linda would be away from our house for five (5) nights and a good portion of six (6) days, so she packed accordingly.  She left for Ann Arbor before mid-morning.

I was waiting for cooler weather to start working on the workshop in earnest, but this morning I at least began.  First up was cleaning up the shop, which had (not unexpectedly) become a disorganized storeroom as we continued to move things from the garage to the barn.  I had dug through tool boxes and storage boxes looking for things I needed for this or that task, with most of them not getting put back where they came from, so step one was to put tools back where they belong.  My toolboxes can be stacked, so once they were properly loaded, I could store them against a wall in the footprint of one case if needed; a very efficient use of space, but not so great if/when I next need a tool.  I already had a folding table (approx. 30” x 72”) set up in the center of the room.  I had a second folding table available, so I set it up next to the first one, long edges together, to provide a work surface for the tools and components I needed to assemble the Rockler Rock-Steady Corner Stands, which were the only two pieces for which I had all of the necessary components.

The first Rockler Rock-Steady Corner Stand assembled and placed in the NE corner of the shop room of the barn.  The legs have height adjustable feet, so the height of the assembled stand ended up being approximately 34 inches.  That will likely change slightly once all of the pieces are assembled and I square them up and level them to accept a work surface.

With the shop cleaned up (more or less) I moved all of the Rockler Rock-Steady work table components into the shop and began assembling one of the two corner stands.  These were the only two pieces for which I had all of the parts, at least I thought I did.  It came with good instructions, and was easy enough to assemble, until I realized they had shorted me 8 of the 5/16-18 3/4” bolts and matching 5/16 washers.  After a bite of dinner, I went to Rural King but the best I could do was 5/16-18 1” bolts and similar washers.  I had a feeling the 1” long bolts might be a problem, but hoped they would at least provide temporary securement until I could resolve the issue properly.

Madeline was due back from Camp Algonquin (YMCA) sometime tomorrow.  The current Camp session ended today, but Mads was spending the evening with her friend (and former neighbor), Marian, and Marian’s dad (Kip) at their family place in Cheboygan.   Mads mom and dad were also due back tomorrow from their 1-week trip to Portugal.  That was good timing, as Linda needed to be at Meghan and Chris’ house to take care of the cats while they were gone to Las Vegas.  Both of the cats (Min and Inches) have health issues, so Linda was there until Meghan and Chris returned later in the week.

 

Sunday 23 … Work shop stands and dinner together

The second Rockler Rock-Steady Corner Stand assembled and placed in the SE corner of the shop room in the barn.  I had a lot of tools and materials “stored” along all of these walls, so it was a bit of job to move all of that to other places.  Where possible, I moved things to the storeroom (above the shop) and tried to place it on shelves in some logical manner, at the very least grouping it with “like items” that were already there.  But some of it ended up along the walls of the RV bas, and some of it just ended up in the west and northwest part of the shop, or under the two folding work tables I set up in the middle of the room.

I continued working on the second Rockler Rock-Steady corner stand using the 5/16-18 1” bolts I bought last night, but I ended up not leaving them in the assembled product.  While assembling this stand I “remembered” (realized) that I had purchased the spacer kits that are used to connect the various Rock-Steady products together in larger configurations.  These spacers are cylinders, ~5/8” diameter by 5/8” long, with 5/16-18 3/4″ threaded studs on each end.  Each spacer replaces a corresponding bolt that came with each product, so two bolts in total.  That made original bolts available for me to use instead of the 1” long ones I had purchased.

Brendan and Shawna got home sometime in the early afternoon.  After a little time to visit and exchange information, Linda headed to Meghan and Chris’ house.  Mads was not home yet, so hearing about her week at camp would have to wait for another time.  I drove to Meghan’s house to meet Linda at 16:00 to have dinner.  We had salad and vegan pizza from Pizza House, courtesy of Chris.  The pizza was excellent, with light tomato-based pizza sauce and just the right amount (not too much) of non-dairy “cheese.”  (We later learned that Chris assembled this pizza himself, as the last time he also asked for “light” cheese but the cooks loaded it up, as they do for the regular pizzas on the menu.)  We hope he decides to add this offering to the menu, as it will open up another place for us to go for dinner and drinks with or friend, Kate.  There should be a market for this in Ann Arbor, but it has to have a net positive contribution to the bottom line.

…

20240617-19_family-friends-projects

Leave a reply

NOTE:  This is a very short post that includes one (1) photo with caption, taken by me (Bruce) with a Google Pixel 6 Pro.

 

MONDAY 17 thru WEDNESDAY 19 June 2024 — Grand-daughters, friends, workshop tables

 

Monday 17 …  Supervising grand-daughters in Ann Arbor and meeting a friend

Linda went to Ann Arbor yesterday for three (3) nights to supervise (and entertain) the grand-daughters.  She arranged to have brunch with Kathi S. today.  Kathi is the mother of childhood friends of our children, and a friend of ours, who now resides in Ann Arbor.

 

Tuesday 18 …  More Ann Arbor & More Garage Doors

Both of the new garage doors are installed and in the open position.  Each one has a wireless exterior keypad.  The one for the smaller door is visible in the photo.

Linda wrapped up her initial 3-nights of child-supervision and entertainment, mostly for our 5-year-old grand-daughter (Sadie).  Our daughter, Meghan, took over from there.

While Sadie was at her day-camp (at Daycroft Montessori), Linda went to Meghan’s house to get detailed instructions on taking care of the cats while Meghan and Chris are away.  She returned to Ann Arbor to gather up a few things and did some light grocery shopping (Whole Foods Market) before returning home.  Meghan picked Sadie up from camp, and provided her supervision and entertainment until Saturday morning, when Linda relieved her.

Our friend, Kate, texted us today to see if we where available/interested for/in getting together tomorrow evening.  We were, but deferred making a decision about where to go until tomorrow morning.

Dan (Everlast Doors) texted to see if he could stop by late afternoon to continue working on the installation of the new garage doors.  He arrived around 16:30.

 

Wednesday 19 … A big delivery; dinner & coffee with Kate

After sharing suggestions back and forth with Kate, we all agreed to go to Bigalora Wood Fired Cucina in Ann Arbor for dinner.  They have non-dairy cheese available for their pizzas, so that worked for us.

I recently ordered numerous work table components from Rockler for the workshop in the barn.  Many of the items arrived today, but the remaining ones are on back-order, with estimated availability of July 28 (this year).  Everything was coming via UPS with a delivery window of noon-16:00.  Shortly after noon, the truck pulled in front of the house.;  I saw it come in, and dashed outside to ask the driver if he could unload at the barn, as that is where all of the pieces will be assembled and used.  He was more than willing to do that.  I met him down there and helped move the boxes from the door of the truck into the barn.  I did not, however, immediately verify if what I had received matched the shipping notifications I got from Rockler and UPS.

Linda booked our flights (DELTA) for our Thanksgiving trip to Florida to visit with Nancy and Paul.

…