Author Archives: BRF

2015/08/08 Fridge Swap Gallery Post

Leave a reply

On this date we finally removed the old refrigerator from the bus and put the new one in.  The exchange took place at Chuck Spera’s bus garage and he operated his forklift.  John Rauch and his son John provided the much needed muscle and we had help from Randy, who owns the business in the suite next to Chuck’s shop.  Here are 19 photos that show some of what was involved.

2015/08/08 (S) A New Bus Fridge (Finally)

Leave a reply

We overslept and did not get up until 7:15 AM.  The weather has been very pleasant all this past week but we awoke to light rain.  We left for our SLAARC breakfast at 7:25 AM and took a different route than usual to see how it would be for the bus.  I headed north on Hacker to M-59, east to US-23, and south to I-96 east.  The ramp from US-23 south to I-96 east is a left exit, left entrance, with a very short merge lane in the middle of a major construction project.  I decided that was not our best option for the bus.

We arrived at breakfast at 8 AM to find a dozen people already there but at least 10 more showed up after us.  We enjoyed the conversation, as we usually do, but did not linger and were on our way back home by 9:15 AM.  As soon as we arrived we changed into our work clothes and got busy with the final preparations to move the bus to Chuck’s bus garage in Novi.

I pulled the bus out at 10:30 AM and Linda followed in the Element, which had all of the pieces we had removed from the old refrigerator along with tools, blankets, and some 2x4s.  The bus roof was brushed by a few small, low branches getting from our house to N. Hacker Road, reminding me that I need to covertly trim trees and bushes along our street.  I say covertly because they are not on our property.  The last time I took the bus out we went south on Hacker to Grand River Avenue.  This would have been our preferred route today except that the trees are not trimmed up in a few places and one of them, just before Bendix Drive, clunked the stuff on our roof pretty hard last time.  I did not care to repeat that so I went north as we had this morning in the car.

At M-59 I headed west to Latson Road, a trip of some four to five miles in the wrong direction.  The reason is that Latson Road going south has a relatively new, and easy to navigate, intersection with I-96.  From there we had an easy run to the Beck Road exit, a short jog south to Grand River Avenue, an easy left turn, and the final mile to Chuck’s shop where we arrived at 11 AM.

Chuck had already pulled his bus out of the building and parked it out of the way but there were several trucks and a dumpster trailer blocking access to his door.  They belonged to a motley crew that the owner of the building in front of Chuck’s shop had hired to clean up some of the mess left behind by the sunroom company that just moved out of the building.  He had me pull up to the right and position myself to back up and then negotiated with the workers to move their vehicles.  I pulled up the tag axles and waited.  The workers were not happy about it but they did it.

To get our bus into Chuck’s shop nose first he had me back parallel to the building and then bring it around to the passenger side into a space adjacent to the front building until I was perpendicular to his door.  I was then able to pull straight in but I did not pull in all the way.  Chuck had me stop with the fixed window frame opposite his forklift which he had already positioned for use.  The on again, off again light rain was not a factor as the window frame we needed to open was well inside his shop.

Linda and I unloaded all of the stuff from the car and brought it inside the shop.  We realized that we forgot to bring the camera so Linda tried to capture the progress of the work with her cell phone camera.  I have put those images in a separate gallery post for this date.

Randy, the owner of the Printology business in the suite adjacent to Chuck’s, came over to see what we were up to and stuck around to help.  With me working from an 8 foot step ladder outside the bus, while Chuck and Linda worked inside, we opened the window frame about 24 inches and propped it with a piece of 2×4.  I then carefully lifted the window higher while Linda sighted along the bottom of the upper cabinet.  When I had the frame high enough to be clear of the cabinet Chuck measured the length of 2×4 we would need to prop it open.

It looked like 52 inches would do the trick.  I had a 56″ piece of 2×4 so I cut it down to 52″ with my 7-1/4″ Rockwell circular saw.  I used the first piece to mark a second piece on an 8 foot 2×4 and cut that.  Linda took both pieces inside the bus where she handled one and Chuck handled the other.  As I lifted the bottom edge of the window from outside the bus the window hinge (at the top) made some unpleasant (and a bit unnerving) sounds but I got it high enough that they could put the two braces in place and the frame did not come unhinged.  We had just finished this task when John Rauch and his son, John, arrived at noon to help move the refrigerators.

The old refrigerator was lying face down in the bus.  The two Johns lifted it as a test and determined that they would not have any difficulty moving it.  Linda fetched one of the blankets and dropped it over the sill of the open window to protect it and the side of the coach.  Chuck had placed the long forks on his forklift about two feet apart and slid a narrow pallet over them.  He raised the forks and brought the forklift forward towards the bus.  We got him to position the top of the pallet even with the top of the sill and about 3″ away from the side of the coach.

John and John are very strong and were able to lift the old refrigerator case and pass it through the window onto the pallet.  With a person on ladders on either side of the pallet we slid the refrigerator all the way out.  Chuck then tilted the forks slightly, slowly backed away, and lowered it down.  John and John got the old refrigerator off the pallet, carried it out of the way, and stood it upright on its base.  They then lifted the new refrigerator onto its back, picked it up, and placed it on the pallet.  They went back inside the bus while Chuck brought the forklift up to the coach and raised the forks until the pallet was at window sill level.  John and John slid it into the bus, stood it up, and rolled it into the alcove.  I then secured it in place with a piece of 1×3 wood screwed to the floor across the front to keep it from rolling out while driving.  There is approximately three inches of space above the fridge but it cannot tilt out very far before the upper back edge catches the ceiling of the alcove.

John, John, and Chuck raised the window frame slightly to remove the 2x4s and close the frame when the top hinge started coming apart.  Linda yelled for me and I scrambled over to get another pair of hands on the frame.  With me and Chuck holding the outside (free) edge and the two Johns holding the hinge edge I was able to see where the hinge was out and direct folks as to what to do.  It took several tries and a few minutes (that seemed like hours) but we got the hinge re-engaged and then closed the window frame.  We took a few minutes to rest and chat and Chuck showed John (the father) his race car.   The heavy lifting was all done so John, John, and Randy took off, but before they did Linda gave John (the son) a gift for their new baby girl, Lucy Violet.

Linda and I put all the shelves and bins in the new refrigerator and then reattached the two doors.  That was a bit of extra work as it came with the hinges on the right side but we needed the door to open on the right side.  With the doors on we took a moment to consider our choice of size and color (black) and felt we had made the right decision.  We started to reassemble the old refrigerator but we were all hungry and decided to go to lunch first.  I started the bus and pulled it all the way into the shop so we could close up.  Chuck then drove us down the street to Panera for lunch.  We took our time and had a nice meal and a nice chat.

Back at the shop we decided to switch the buses around so Chuck would be free to leave.  He wanted a picture of the two buses together so I backed ours out of his shop, swung around to the passenger side, got parallel to his bus, and then backed up so the nose of our bus was about 10 feet behind the nose of his.  He and Linda then both took photos with their cell phones.  When the photo shoot was done I pulled forward to the left and then backed in parallel to the building about four feet from the curb.  That gave Chuck plenty of room to pull up next to me on my passenger side and then back around next to the front building and get lined up to pull straight into his bay just as I had done earlier.

Back in the shop Linda wiped out the inside of the old refrigerator and then we reattached the two doors.  As she cleaned each rack, shelf, and bin I placed it back into the refrigerator.  When it was fully reassembled we plugged it in.  It came on, ran for about 60 seconds and then shut off.  It obviously was not cold yet, and might have been cause for alarm if I had not dealt with this “problem” before.

I knew from prior experience that the defrost timer had probably disconnected the compressor and connected the evaporator defroster.  Chuck pulled out three of his lawn chairs and we sat around waiting for the refrigerator to restart.  The only thing missing was three cold beers.  We knew the unit still had power as the lights were working.  There was an outside chance that the overload protector (fuse?) might have blown, but I did not consider that to be likely.  Our patience was rewarded about 25 minutes later when the compressor came back on.  While we were waiting we gathered up our tools and various materials and loaded everything back into the Honda Element.

Chuck had a message from his wife, Barbara, with her ETA so we decided to settle back into the lawn chairs and kibbutz until Barb arrived.  She showed up a little while later and Chuck got out a fourth chair and we sat in the shop listening to the sound of the functioning refrigerator and debriefing the events of the day.  As a result of the window frame hinge coming loose I am now of the opinion that I did not need to remove the two stop blocks.  I suspect they are there to “stop” the hinge from coming apart and I should not have removed them.  Chuck is also thinking about replacing the refrigerator in their bus and is going to check with Prevost regarding these blocks.  As much as anything I was annoyed with myself for the amount of time I wasted removing these blocks but what is done is done and I now need to reinstall the one block that came off undamaged and get a replacement for the other one, even though I can only attach it with one machine screw.  Butch thinks he can make one for me, otherwise I will have to get one from Prevost.

Our local electrical utility, DTE Energy, will pick up used appliances.  In the case of a refrigerator it has to be plugged in and running, which I presume means it is functioning and cooling the interior.  If so, they will take it away and send us a check for $50.  From our end that’s a good deal as we don’t have to pay someone to haul it away.  Because of the R-12 Freon there are very few places that will deal with it.  My guess is that DTE has a sub-contractor who will recover, clean, and recycle the R-12, which is no longer being made and has become very expensive.  They may also recycle the copper tubing and electrical wire, and possibly the metal case and other materials.  Even with the labor to do this work the unit must be worth more than $50 to them.

We all needed to get some dinner so we wrapped up our visit and started up our bus.  I pulled out onto westbound Grand River Avenue followed by Linda in the car.  At Beck Road we turned north and then got on I-96 westbound.  The bus was at 3/8ths of a tank of fuel so I decided to stay on I-96 and go to the Mobil truck stop at M-52, a run of about 30 miles that would allow the engine and transmission to come up to normal operating temperature.  Linda exited at Latson Road and stopped at Meijer’s to do some grocery shopping.

The Mobil truck stop is run down with a very poor, pot-holed apron and parking area, but there are usually several tractor-trailers fueling here when we pull in as it is one of only two places that a semi can refuel between Detroit and Lansing.  There weren’t any trucks getting fuel when I pulled in but it was 7:30 PM on a Saturday evening and there were a half dozen tractor-trailers settled in the parking area for the night.  I poured two bottles of Stanadyne diesel fuel additive into the fuel tank followed by two ounces of Racor Biocide.  I then added 125 gallons of diesel fuel to the tank, which took about 11 minutes.  By the time I paid for the fuel and was ready to pull out it was 8 PM.

I called Linda to let her know I was on my way and then reset the trip odometer.  I drove east on I-96 for 10 miles to the M-59 / Burkhardt Road exit and got on M-59, which only goes east from there.  Eleven miles later I made the turn south onto N. Hacker Road and completed the drive to our house.  Linda heard me idling in the street, where I stopped to lift the tag axles before making the tight right turn into our pull-through driveway, and came out to help get me parked.  Once I was positioned correctly I put the tag axle back down, let the engine low idle for a minute to let the turbo spin down and let the heads cool off and the temperature to equalize, switched the Level Low system out of drive mode, and shut off the engine.  I shut off the air supply to the engine accessories, shut off the chassis batteries, connected the shore power cord, locked everything up, and went in for the evening.

It had been a long day and we were glad to have it behind us.  I had been anticipating the refrigerator exchange, with some dread, for well over a month.  The concern was that we would not be able to move the units out/in through the window frame, requiring us to remove and replace the lower passenger-side windshield, or that something would go wrong, like the hinge, and turn out to be an expensive and difficult problem to fix.  With each passing day it was also becoming a bottleneck in our remodeling project, at least psychologically if not physically.  But it was finally done and ended well.  We will plug in the new refrigerator tomorrow to make sure it works.  We tested it in Chuck’s shop when it was delivered so we expect it to work now.  There is a lot of work to do but now we can get on with it and I expect it to go well.

In spite of being tired we stayed up and watched the PBS broadcast of the Simon and Garfunkel reunion concert they did live in New York City’s Central Park 10 years after they split up as a duo.  Their music remains among my most favorite from my youth and it has lost nothing with the passing of many years.

 

2015/08/07 (F) Arrangements

Leave a reply

We had our usual, but never boring, homemade granola with fresh blueberries for breakfast.  I brewed a pot of the Costa Rican half-caff coffee we bought yesterday without tasting it first.  We found it to be somewhat bitter, which is not our taste in coffee, so we probably will not buy more after this batch is gone.

We spent a good part of the morning researching cabinet pulls on the Cabinet Service Hardware (CSH) website.  We found a pull on the CSH website that appeared to be identical to the one from The Home Depot, which is a Rockefeller Antique Brass from Liberty Hardware.  The one from CSH was a Belwith Keeler HH.P135-AB for $2.47 each.  The one from The Home Depot was $2.48 plus tax but no S&H.  Since we have the one from THD in hand and like how it looks we will probably buy them locally.

Many of the drawers in the bus have the pulls attached to the walnut face and then the face attached to the front of the drawer box.  Thus, the only way to remove the pulls is to first unscrew the box from the face.  I took the face off of one drawer and installed the new pull.  It fit perfectly, confirming that the mounting hole spacing is 3″ center-to-center.   The one from THD comes with 1″ and 1.5″ #8-32 machine screws but it looks like we will need something shorter than 1″ for the framed drawers and shorter than 1.5″ for the solid drawers.  The cabinet doors have 3/4″ thick frames so the 1″ machine screws may work for those.  Thus we should be able to use some of the machine screws that come with the pulls from THD but will have to buy some as well.  The pulls from CSH do not come with screws so we would have to buy those anyway.

Linda left around noon to meet Diane in Livonia to see a movie (Ricki and the Flash) starring Meryl Streep, Kevin Kline, and Rick Springfield.  I went on an errand run while she was away.  At The Home Depot in Howell I found 10 packs of the drawer pull we like so the price came out to under $2 per pull compared to $2.48 when purchased individually.  We need 58 to replace all the ones in the coach plus at least four for the new desk drawers so I bought six 10-packs.  We have not decided if we will replace the single screw round pulls on the two TV cabinet doors with the double screw pulls.  If we do we will need a couple more pulls.  If not, we will need two round pulls in the same style and finish, which THD also carries.  I bought small packs of #8-32×3/4″ and #8-32×1-1/4″ lengths so I can figure out what lengths work best in each location.

Jarel called while at was THD.  The plans for the built-in sofa had arrived in today’s mail and he had a few questions.  We talked through the issues and came to the conclusion that it would be better for us to come down on Wednesday instead of Tuesday to pick up the desk.  That will give him time to cut the sofa pieces and do some minor assembly and finishing.  The plywood seat and side pieces need to be stained to resemble the walnut hardwood and a 3/4″x3/4″ piece of walnut hardwood needs to be attached to the front edge.  He also needs to cut the piece of walnut veneered plywood for the front and then spray everything with the same lacquer he has used on all of the walnut desk pieces.

As I was finishing up at THD I also got a call from Chuck letting me know that everything was on track for the refrigerator swap tomorrow.  My next stop was at the Howell Lowe’s for a 4′ x 4′ sheet of 3/4″ plywood but I did not like their selection any better than THD.  I ended up buying two quarter sheets (24″ x 48″) of birch plywood.  This plywood has a lot of thin layers, so it is very flat and dimensionally stable, with defect free surfaces that are sanded smooth and very clean edges.  These sheets will go on the bottom of the refrigerator alcove in the bus to elevate the new refrigerator above the new vinyl tile floor.

Back home I texted Josh at Coach Supply Direct, called Terry at A-1 Upholstery, and called Butch regarding the change in our visit date for next week.  Linda got home shortly thereafter and helped me reattach the edge trim to the two doors of the old refrigerator and load them into the back of my car.  We covered everything with blankets and then loaded all of the drawers, shelves, racks, and bins.  Once the old fridge is out of the bus we will clean it, reassemble it, plug it in, and make sure it is cooling.  We will then call DTE Energy to arrange pick up through their recycling program.

Loading pieces of the old refrigerator into the back of the Element to take to Chuck's shop.

Loading pieces of the old refrigerator into the back of the Element to take to Chuck’s shop.

Linda bought an Amy’s Roasted Vegetable Pizza while she was out and cooked it for dinner.  It is our favorite store bought pizza, and much better (for us) than what we can usually get at restaurants and pizzerias (with the exception of Satchel’s in Gainesville, Florida), but not as good as the pizza we had while Mara was here.  That pizza was memorable.

After dinner I got a shower and then worked on the design/drawings for the seat and back cushions for the built-in sofa for the bus.  I started editing blog posts for July but did feel like uploading them.  We went to bed earlier than usual as we had to up at 7 AM tomorrow to go to our weekly ham radio club breakfast.

 

2015/08/06 (R) Three Quarters Framed

Leave a reply

As usual, we started the day with breakfast and then enjoyed our coffee while reading and writing.  Best Pest Control showed up mid-morning to apply the second treatment for hornets, wasps, etc. so we closed up all of the windows and doorwalls while they sprayed.

We located a Wayne-Dalton facility in Livonia so I called them.  As I suspected they were the factory distribution center and would not sell to us directly.  They did, however, give me the name of one of their customers, a business in Milford named The Door Doctor that had a retail store front.  I called them and they had a 12 foot length of the required D-channel bottom weather seal for our small (8′) garage door.  It turned out that they were not actually in downtown Milford but were more conveniently located near the Milford Road exit of I-96.  When the pest control guys were done and gone I drove over and bought the seal.

Back home Linda made quesadillas for lunch and set out some yummy black grapes.  We then made an errand run to Howell.  Our first stop was at Teeko’s Coffee and Tea where we ordered a pound each of fresh roasted Ethiopian Yirgacheffe half-caff and Costa Rican half-caff beans.  The Yirgacheffe is one of our favorites.  The Costa Rican is something new for us.

Our next stop was The Home Depot for a half sheet (4′ x 4′) of 3/4″ plywood.  They only had one type in a 4′ x 4′ size and I did not like it so we did not buy it.  They had nicer plywood in full sheets (4′ x 8′) but I did not need that much and did not want to fuss with something that size.  We did, however, find a drawer/cabinet pull that we liked and bought one to try out with our bus cabinets.  It’s a Rockefeller style from Liberty in an antique brass finish for a 3″ center-to-center hole spacing.  They also had a matching single screw knob in case we need it.

Our next stop was the Howell Art and Frame shop in downtown Howell to pick up three of our four pieces of artwork.  The owner, Rick, had ordered the fourth frame the wrong size and had to reorder it.  The three that were finished looked very nice and I would like to think that the artist, Ann Metzger, would have been pleased with our choices.  Ann was married to my mother’s cousin and took up painting as rehabilitation therapy for breast cancer surgery in her early 40’s.  She turned out to be quite good and was active in the St. Louis artist’s guild for many years.  We have collected many of her works over the last 44 years.

We stopped at Lowe’s to look at their drawer pulls but they did not have anything similar to the one we got at The Home Depot.  We stopped back at Teeko’s to pick up our coffee order and then headed home.

Back home we moved the paintings to the library and turned our attention to installing the seal on the 8 foot wide garage door.  With the door all the way up we were able to slide the old seal out towards the larger door.  I thought we could install the new one with the door in the same position without removing the track from the bottom of the door.  That was, indeed, the case but it did not go in easily.  I trimmed the ends and ran the door up and down a few times and made minor adjustments on each end until it worked properly.  We still need to redo the side and top seals for both doors.

I tried programming the garage door remote control in my car the day we installed the new opener on the small garage door but wasn’t able to.  At the suggestion of the woman at The Door Doctor, I Googled the model numbers of our various remotes and found the manuals.  I had forgotten that the four 3-button remotes we bought a couple of years ago had to be configured before they could be paired with the openers.  Once I knew how to do that I was able to program mine and Linda’s to work with both doors.  Each of our children also have one and I will have to re-program those the next time they are here.

I exchanged e-mails with Josh at Coach Supply Direct about picking up the extra fabric we ordered, perhaps next Tuesday.  I also e-mailed and texted with Jarel about picking up the desk pieces next Tuesday and possibly the pieces for the built-in sofa.  He did not, however, receive the mailing tube with the drawings and cut sheet today, so we will see if that works out.  I suggested he defer work on the pull-out pantry in favor of the sofa pieces as that will allow me to keep working while he is on vacation at the end of this month.  He still owes us a price estimate for the pantry but at this point it almost doesn’t matter as he will be the one building it regardless of the number.

I talked to Terry at A-1 Upholstery in Elkhart regarding the sofa cushions.  She and her mom, Lou, run the business.  I last talked to Terry in early June and she remembered the conversation.  I described once again what we were looking for and she gave me a rough estimate of the cost.  She said we could stop by Tuesday morning to drop off the fabric and discuss the job and thought they could have it finished by the end of August.  That would be great timing for us.  We are starting to feel like this whole project will come together nicely once we get the refrigerators swapped and can finely get back to work on the floor of the bus.

I installed the new Morgan M-302N I.C.E. style lightning arrestor and connected the radio and antenna cables.  I had a short QSO with Mike (W8XH) via the South Lyon 2m repeater and had no issues on transmit or receive.  I started working on a gallery post of 45 photos from the ARRL Field Day event at the end of June but only got half of it done before dinner.

Linda made a delicious zoodles dish for dinner.  Zoodles are zucchini noodles that she cuts with her SpiraLife slicer and uses in place of grain or rice pasta.  The dish had the usual garlic, onion, olive oil base but also had shallots, mushrooms, kale, and sun-dried tomatoes.  We had fresh watermelon later for dessert.

After dinner I finished the gallery post while monitoring the Novi and South Lyon repeaters.  I then had a long QSO with Mike (W8XH) and Steve (N8AR) that gave me a chance to test the M-302N lightning arrestor on both VHF and UHF at three different power levels.  We continued to have the minor problem with quick, apparently random, audio dropouts on our Yaesu FTM-400 dual band radios.  The apparent randomness has made it difficult to puzzle out what might be causing this and we all agreed that we need to set aside time to plan and execute a systematic test and record the results for analysis.

Butch called to chat about house (bus) battery cabling and other things.  I mentioned that we would be coming down on Tuesday and would try to arrange our timing so we can stop and visit over dinner.  We then watched The Princess Bride on DVD.  It’s our all-time favorite movie and I long ago lost count of how many times we have seen it.

 

2015/08/05 (W) No Mask Wednesday

Leave a reply

Linda was up at 6 AM and left for the bakery around 6:20 AM, I think. I was more asleep than awake and did not get up until later. I wanted to do a load of laundry but needed powdered detergent which I did not have. I also needed to make a run to Lowe’s so I left to take care of my errands without making coffee or having breakfast.

I picked up a couple of 2x4s at Lowe’s that I will use to cut a pair of support arms for propping open the fixed window in the bus while we exchange the refrigerators. I was going to buy a 4’x4′ (half sheet) of plywood to cut for the base of the refrigerator alcove but did not care for the selection. I also did want to wrestle with the size and weight by myself. I will have to go back to The Home Depot with Linda to get what I need. I got my laundry supplies across the street at Meijer’s and headed home.

After unloading the 2x4s I thought I would program the remote control in my car for the new garage door opener. The procedure is very simple but much to my dismay the remote would not connect with the opener. The remote is a 3-button model made by Chamberlin, and both garage door openers are identical Chamberlin models. We have four of these 3-button remotes, one for me, one for Linda, and one for each of our children. We got the 3-button model because we have two overhead doors on our garage and plan (hope) to have a barn someday with an overhead door. All four of the 3-button remotes programmed to the large garage door without a problem and the new door opener came with a single button remote that works just fine, as did the large garage door opener. I won’t know if the problem is the opener or my remote until I can try programming Linda’s remote. If her remote will program then I know it’s my remote, but if it won’t program I still won’t know where the problem lies.

I had originally planned to mask off the interior of the bus today so I could start sanding the floor tomorrow but decided to put it off. Not only would the painter’s plastic be difficult to manage by myself, I realized that it did not make a lot of sense to tape it up in advance of doing the refrigerator swap. I was on the phone with Chuck arranging to bring our bus to his shop this weekend to take care of the refrigerators when our USPS carrier, Michelle, came to the door bearing gifts. Well, OK, they were packages, but I did not expect them until tomorrow so that made them more like gifts in my mind. One was from Amateur Electronics Supply (AES) and the other was from Morgan Manufacturing, so it was all ham radio stuff.

I went to my ham shack/office and mounted the control head for the Yaesu FTM-400 on the stand that just arrived from AES. I e-mailed Steve (N8AR) to arrange a time to test the lightning arrestor before installing it in our cable entry box. I then e-mailed Jarel to start trying to arrange a day next week to drive to his shop in Logansport, Indiana to pick up the custom walnut desk. Finally, I e-mailed Josh at Coach Supply Direct to make sure he was going to be around. I was checking out the TVFool.com website, which Steve recommended, when the art frame shop in Howell called to let us know that three of our four paintings were ready to pick up. They would have all been done but he ordered the forth frame the wrong size and had to reorder it. Linda then called to let me know she was on her way home from the bakery. So much communication, so little time.

When Linda got home we discussed going out to dinner and researched a new place that had opened in Howell. As usually happens, however, there is almost no place that serves anything we choose to eat and we ended up staying home. Linda had a couple of Boca burgers in the freezer and we had those with corn-on-the-cob and fresh fruit (peaches, nectarines, and strawberries). We eat better food, and in smaller quantities, when we dine at home.

After dinner I caught Steve (N8AR) on the radio and we agreed that I would bring the lightning arrestor over to his QTH at 8 PM. I had an e-mail related to the draft of the July issue of Bus Conversion Magazine and checked to make sure a correction had been made correctly.

At Steve’s house my lightning arrestor tested better than the previous one, and should work OK in my system, but it was very clear that there is something wrong with the design and/or manufacturing of these VHF/UHF I.C.E. units. We also came to the conclusion that the quality control testing the manufacturer was doing (if any) was inadequate to reveal the problem. I expect, however, that this one will work when I install it so if it is typical of their units most hams would not have a reason to suspect that it was flawed. Someone would have a problem with it, however, as it is clearly not usable for all frequencies from 40 MHz to 1 GHz as stated on the label. My unit has a 0.31 dB loss at 445 MHz (it should be 0.01) but has an 11.59 dB loss around 635 MHz, which is a huge factor of 16 times loos of signal, and the loss from 500 MHz to 1 GHz is unacceptably large making it useless in that range of frequencies.

Steve captured all of the data and e-mailed it to me. He then tested one of his Polyphaser lightning arrestors and sent me that data file. He also sent me the link to the VNWA software from SDR-Kits.com that I needed to work with the data file. We spent a few minutes talking about the problem we are having at home with our ham radio transmissions interfering with our OTA TV signals. He sent me a link to the free student version of the ELSIE (“L”,”C”) filter design software.

I left about 9:45 PM and called my friend, John Rauch, to see if Saturday noon would work for him in terms of our refrigerator swap. He said it would and that he would check with his son (also John) to see if he could/would also help. I will let Chuck know tomorrow that it looks like Saturday is a “go.”

Linda was asleep by the time I got home so I worked in my office until after midnight. I captured the data attached to the e-mails from Steve and then downloaded and installed both the VNWA and the ELSIE software. I then uploaded my personal blog posts for June 28, 29, and 30. I logged in to the FMCA Freethinkers website, the FMCA GLCC website, and the SLAARC website and installed updates for the themes and numerous plug-ins. With that I came back upstairs and worked on this post in the living room so as not to disturb Linda and finally went to bed around 1 AM.

 

2015/08/04 (T) Back to Busics

Leave a reply

The weather finally turned cooler yesterday and the overnight lows dropped into the upper 50’s; perfect sleeping weather.  We had the house open all day and left windows open overnight.

After breakfast and coffee we worked in the bus for the rest of the morning.  I wanted to clean out all the remaining items from the drawers and cabinets before we start sanding the residual thinset and mastic.  Our first task was to get the refrigerator out of the way.  We laid it down on its face with cardboard under it and slid it forward and over to the passenger side behind the co-pilot seat.

We surveyed all of the storage areas and decided it would be easiest to remove all of the drawers from their slides with the stuff still in them.  The drawer boxes release from the two side-mounted slides at the front via a plastic clip.  The back edge of the part of the slide attached to the box then slides out from under a small tang, allowing the drawer to be lifted out.  An added benefit to removing the drawers is that it will be easier both to clean them and clean the face frames on the built-in cabinetry.

Linda decided to go through all of the stuff as it came into the house, sorting it initially according to whether we should keep it or and throw it away.  Of the things she thought we should keep the next step was to clean them if needed, or queue them up for cleaning.  That included almost everything related to the kitchen.  She reorganized the stuff that was already in the small bedroom, putting cardboard boxes in the recycle pile while I took some ham radio related stuff down to my office.

Linda emptying the inside of the bus.

Linda emptying the inside of the bus.

By noon we had the kitchen and part of the bathroom cleaned out.  I decided to take a break from bus work and install the new bottom weather seals on the garage doors.  I unscrewed the mounting track from the bottom of the 16 foot wide door and removed it.  It had years of accumulated dirt in it so I cleaned it out.  With Linda’s help we got the new seal installed, using soapy water as a lubricant, and reattached the track to the bottom of the door.

Our luck did not hold up with the 8 foot wide door.  Both doors are Wayne Dalton products but the 8 footer is not as thick.  The bottom track for the weather seal is only about an inch wide and the replacement seal, which is designed for a “T” channel would not fit.  Closer inspection suggested that the proper seal would have a cylindrical edge rather than a “T.”  We checked online and found a supplier through Amazon but held off ordering until we had a chance to check for local sources.

We had lunch, after which I went to The Home Depot to see if they had any garage door seals that were different from the one’s at Lowe’s.  They did not.  There is a branch of our bank adjacent to The Home Depot so I stopped there and then headed to Lowe’s where I returned the weather seal for the 8′ door.  I then bought a 400 foot long roll of 9 foot wide 0.31 mil painter’s plastic and four roles of 2″ painter’s tape.  We will use this to mask off the cabinetry before we start sanding the floor or taking on other parts of the interior remodeling project that might affect the woodwork or furniture.

Back home I continued emptying out the house portion of the bus.  (The basement bays are a whole other story.)  In order to remove one of the last three drawers in the bedroom we needed to remove the bed platform.  It is 3/4″ cabinet grade plywood sized to support a queen size mattress, definitely a two-person job.  It is hinged about 18″ from the head end, so we folded that piece over and secured it on both edges with tape, shortening the total length by that much.  It was still heavy and very awkward to handle, especially getting it through the cockpit and down the entrance stairs, but we managed to get it out.  I used a hand truck to move it to the garage for safe storage.  Linda commented that perhaps we should cut it down and switch to a full size mattress.  I think that is an idea worth considering as it would give use more aisle space.

The storage base for the bed with the plywood platform removed.

The storage base for the bed with the plywood platform removed.

The plywood platform is 80″ L by 58″ W so even after removing the 18” piece at the head end is 62” x 58”.  That means it was not cut from a 4’ x 8’ sheet of plywood and would be almost impossible to replicate.  Our mattress is approximately 78″ L by 60″ W whereas the foundation box (storage compartment) is 72″ L by 43″ W.  Our full size mattress in the middle bedroom is 72″ L by 52″ W.  Cutting the plywood platform down to full size (or building a new one) would gain us 8″ of isle space at the foot of the bed and 3″ on each side.  That may not sound like much, and would be irrelevant in most bedrooms, but it would be a significant difference in the aft cabin of our land yacht.  If we do this I would keep/store the existing plywood and build a replacement.

With the bed platform out of the bus I was able to remove the last three drawers across the back.  The one farthest to the driver side, in particular, could not be removed with the platform in place.  Another reason for building a new bed platform is that I can hinge it closer to the head end and use longer gas springs.  This would allow it to open far enough to provide easier access to things stored under the bed and be able to install and remove the three drawers whenever needed.

Linda heated up some frozen breaded mock fish fillets for dinner.  She made fresh vegan tartar sauce to go with them, boiled some corn-on-the-cob, and roasted some potatoes in the oven.  It was a simple but very satisfying meal.  After dinner I uploaded more blog posts, getting two of the three that cover the ARRL Field Day event done.  That means I am almost through the month of June!

 

2015/08/03 (M) Happy 37

Leave a reply

Today is our son’s 37th birthday anniversary.  Happy birthday Brendan.  Linda sent him a happy birthday text and his reply confirmed that they are at Tahquamenon Falls in Michigan’s Upper Peninsula.

My main task today was to finish the design of the built-in sofa for the bus and get the drawings in the mail to Jarel Beatty, the cabinet maker in Logansport, Indiana.  I dovetailed that work with breakfast, lunch, and a long chat with Pat Lintner from our FMCA Great Lakes Converted Coaches (GLCC) chapter, but by 2 PM the two 17″ x 22″ sheets were ready.

I was not satisfied with the quality of the copies I got from The FedEx Office store in Brighton so I drove to the store in Novi where their large sheet scanner/printer does a really nice job.  Copies in hand I drove to the post office in Brighton, bought a Ready Post mailing tube, addressed it, put the copies inside, and sent it on its way.  Back home I sent Jarel an e-mail letting him know the sofa drawings were on their way and explaining them a bit.  I then settled in to continue uploading blog posts to our website.

Later in the evening I got a text message from Jarel with three more photos of the custom walnut desk.  He had sprayed all of the pieces and was letting them dry.  He planned to work on something else tomorrow but thought he would have the drawer slides and drawers installed by the end of the week.  He will probably start on the pull-out pantry but wasn’t sure he would get it done before he leaves for a vacation trip on the 21st.  It is unlikely that the built-in sofa pieces will be done by then and the HVAC chase cover needs to wait until after the desk is installed in order to get a final, accurate measurement for its length.

I will probably drive down and get the various desk pieces from him before he goes on vacation so I can install them as soon as the new floor is installed.  I have to install the two fan-coil heat exchangers in the bases and redo the hoses before I can put the pedestals in place so it will be easier for me to do this at home.  As part of the same trip I will stop at Coach Supply Direct in Edwardsburg, Michigan and pick up the fabric we ordered for sofa cushions.  If we decide to use A-1 Upholstery in Elkhart I will drop the fabric off there along with drawings of the cushions we need made.

For my evening relaxation I read a little more of “Number Theory and Its History” by Oystein Ore and then went to bed.

 

2015/08/02 (N) No Swap Sunday

Leave a reply

The forecast for today was for warm, humid weather so we closed up the house and turned on the air-conditioners as soon as we got up.  We left around 9 AM for the Howell Farmers Market so I did not make coffee and we did not have breakfast.  At the market Linda bought a nice assortment of fresh vegetables.  I bought a bag of Kenya AA coffee beans from Teeko’s and some apricot and raspberry Rohlicky from the Czech Bakery.  It turns out they are not vegan so I won’t buy them again.

We decided to see if John and Diane were available for dinner.  We had no sooner made these arrangements when I got a text message from Chuck indicating that the coast was clear at his shop in Novi and we were good to go on the refrigerator swap.  I talked to him shortly thereafter and indicated that we had assumed it would not be today so I had not yet cut the support 2x4s or found the additional help that we would need and, in light of that, had made other plans.  That was fine with him and we agreed to aim for next weekend.

Linda surveyed her inventory of ingredients and decided that the warm Farro with dried cranberries and nuts would be a good dish to have Diane help make.  Diane retired at the end of the school year in June and had asked Linda if she would show her some of the ingredients and prep/cooking methods she uses.  Linda likes working with friends in the kitchen, sharing what she has learned and learning new things herself in the process.  Diane is her longest term, non-family friend.  As an English teacher she had lessons to prepare and papers to grade almost every evening.  As a result John, who has worked most of his adult life as a framing carpenter, took care of preparing their evening meals.  Now that Diane is free of her teaching obligations she would like to learn more about cooking.

Linda wanted some non-dairy ice cream for dessert so I was sent to get it.  I went to the Home Depot in Brighton first where I bought some thin (1/8th inch thick) rubber sheet material, a small tool pouch, and 2-person forearm lift strap.  The rubber material will be for the edges of the plywood in the new built-in sofa, cushioning the seat when it is closed.  The tool pouch is for working on the tower (my carpenter’s tool belt is too big) and the lift strap is to help with the refrigerators and anything else heavy we might need to move.

The only place within a seven mile radius of our house that consistently has the non-diary “ice cream” we like is the Kroger on M-59 at Old US-23, so that’s where I headed next.  In addition to the Coconut Bliss they had a cashew milk based product so I bought some of each.  I bought vanilla and salted caramel in the CB brand and snickerdoodle in the cashew product.  By the time I got home I only had a couple of hours left before John and Diane were due to arrive so I worked in my office and uploaded blog posts for June 16 – 20.

John and Diane arrived right on time at 4 PM.  I opened our bottle of Viva La Roja from Heart of the Desert Winery in Alamogordo, New Mexico and we settled in to easy conversation.  I found this red table wine particularly to my liking; very smooth with a hint of sweetness and no tannin.

Linda and Diane eventually started preparing dinner.  John and took that as an opportunity to go look at the bus project.  The ladies made a mixed greens salad with dried cranberries and other add-ins and put out a choice of dressings and sliced a loaf of Italian bread that they brought, along with a bottle of Pinot Grigio that we opened to have with the meal. The main dish was Farro with dried cranberries, almonds, onions, garlic, and kale.  It was all very tasty and well received.

By the end of the meal it had cooled off enough to sit on the deck comfortably.  Linda served the cashew milk snickerdoodle non-dairy ice cream with fresh sliced strawberries and it was very good.  I showed them what we had done with antennas on the tower and the cable entrance box and then we went back inside.  John still works full-time so they left around 9 PM as it takes at least 30 minutes to get back to their house in Farmington Hills which is about a mile from our old house.

 

2015/08/01 (S) Refrigerator Swapping (NOT)

Leave a reply

We had a good crowd for our weekly SLAARC breakfast.  We sat across from Mike (W8XH) and had a chance to discuss what to do about the ‘extra’ user accounts on our computers.  We also discussed the release of Windows 10 that occurred on the 29th of July and all came to the conclusion that we would not be upgrading anytime soon.

When we got home I talked to Chuck on the phone.  He said the sun room company was still moving out of the building in front of his shop and that there was still too much stuff in the way to be able to move our buses around.  Given the circumstances we agreed that we would not do the refrigerator swap today and probably not tomorrow.

At breakfast Mike suggested that we look in the Users folder on our computers to see what files were associated with each of these previously unknown users and then delete the User accounts.  It turned out that these users did not exist, or at least had no folders or files associated with them that we could find.  Linda’s computer did, however, have a couple more folders in the Users folder that did not have User accounts associated with them.  When we deleted each of the phantom accounts we were given the option of saving any associated files in a folder on the desktop.  We selected that option each time but no such folders ever got created, confirming (I suppose) that there were no files associated with that account.

Bill, who takes care of the computers and software for the bakery, installed software on our machines when we first got them and Linda speculated as to whether these phantom accounts might have been inadvertently created at that time.  At this point we will probably never know.  We have strong security systems in place and are reasonably careful in how we interact with the online world, but it was a bit unnerving to find these accounts on our machines.

We were on tap for another warm, humid day and I elected not to do any work on the bus or in the garage.  With the phantom User accounts taken care of I transferred the photos that I received of the custom walnut desk from Jarel from my SG3 phone to my laptop computer and edited them for use on our blog.  I copied recent photos from my DSLR camera to my computer and then settled in to copy blog post drafts from e-mails into Word and edit them.

In the course of the day I did a couple of loads of laundry, worked on the sofa design/drawings, chatted on the ham radio, and took time out to have lunch and dinner, which was the left over Pad Thai.  Having sat for a day or two the dish had absorbed the liquid and, although Linda thought the broccoli was now too soft, I liked it better than when it was freshly made.  I also got to add a generous amount of peanuts, which is how I remember Pad Thai being served in restaurants.  After dinner I started reading “Number Theory and Its History” by Oystein Ore.

 

2015/07/31 (F) A Blue Moon Family Gathering

Leave a reply

As soon as Linda got up this morning she busied herself making collard greens cole slaw while I made our morning coffee.  Once the cole slaw was assembled and in the refrigerator we had breakfast.  We were due at our daughter and son-in-law’s house later in the afternoon for a family gathering so we decided not to take on any overtly physical tasks today.  We both got cleaned up instead and settled in to more sedentary tasks.

Linda has been getting somewhat regular text messages from Mara apprising us of her travels and I have been getting text messages from Jarel with photographs of the progress on the construction of our custom walnut desk/workstation for the bus.  Linda worked at her desk and I worked in my office transferring the photos from my phone to my computer and working on the design/drawings for the built-in sofa.

Linda restarted her Samsung laptop computer (for some reason that I do not recall) and was presented with a choice of four user profiles for logging in.  One was hers, one was named ‘Diane,’ and two of them where random letters.  Until that moment we were unaware that these other accounts existed on her machine.  She selected her usual account and logged in.  I checked my ASUS laptop computer and discovered that I also had a user profile named ‘John’ of which I was unaware.  We noted that we have, coincidentally, been good friends with a couple named John and Diane for 36 years.

I e-mailed Mike (W8XH) to ask him about this situation.  He is a friend from our local SLAARC ham radio club who works part time as an independent computer service provider and has become our ‘go to’ guy for computer issues that do not involve the bakery software or VPN.  Because he is often working during the day I do not always hear back from him immediately, but we knew we would see him at breakfast tomorrow and decided not to do anything until we had talked to him.

We plinked away at our tasks until it was time to get ready to go to the family gathering.  Brendan and Shawna were headed ‘up north’ and needed to borrow a few things.  We had previously gathered up our portable induction cooker and battery powered camp lantern and loaded these in the Element along with the Thule car top carrier.  We loaded the cole slaw, a bottle of wine for dinner, and a bag with a couple of gift bottles of wine and cards for Brendan and Shawna’s upcoming birthdays, and headed for Dexter.

Meghan and Chris are very interested in professional sports and today at 4 PM EDT was the trading deadline for 2015 Major League Baseball season.  That’s a big deal if you are really into professional baseball.  They had the radio on when we arrived and were following the trading action closely.

Meghan had obviously been hard at work on dinner preparations long before we arrived.  She and Chris had acquired a Sous Vide, a countertop appliance for cooking foods in sealed bags immersed in hot water, and she was cooking country style pork ribs with two different sauces. The bags had been in the Sous Vide for over 24 hours and from comments during dinner the meat was obviously very moist, tender, and tasty.  Meghan had also prepared tempeh for us.  She had soaked it and then pan grilled it with the same two sauces; a classic bar-b-que and a mustard.  Except for the meat everything else was vegan; collard greens cole slaw, corn-on-the-cob, potato salad.  Meghan had a pudding bar for dessert that included vegan tapioca and chocolate puddings in addition to regular chocolate pudding, and lots of toppings.

Before dinner Brendan and I tried to figure out a way to mount the Thule car top carrier on their Subaru Outback but it became clear fairly quickly that we did not have the correct adapters and could not engineer a way around that.  There was no possibility of buying them at this point so we put it back in our car to take home.

Grand-daughter Katie and boyfriend Josh arrived late having run into traffic on their drive back from Iowa.   Brendan, Shawna, and Madeline were still there but getting ready to leave.  After introductions Katie and Josh had dinner.  Meghan then got out the “Ticket To Ride” board game.  We played one complete game with me and Linda working as a team.  This is Katie’s favorite game and she came in first.  Katie is very bright but is also, apparently, very competitive.  This was a side of her we had not seen previously.

By the time we were done it was dark so we all gathered up our things and bid each other fair well.  It was a clear night and the full moon had just risen and now shone brightly over the land.  It was a Blue Moon, the second full moon of the month, and the kind of evening that you could see well enough to go for a midnight hike in the woods.  The next Blue Moon will be in January 2018, so that are not common events.

 

20150730GP H3-40 Custom Desk Build

Leave a reply

Here are a few photos of the new desk for our bus in the process of being built.  All photos are courtesy of Jarel Beatty, Jarel Beatty Cabinetry, Logansport, Indiana.

2015/07/30 (R) Number Theory

Leave a reply

We awoke to a decidedly different air mass than we have been experiencing the last week or so; cool with noticeably lower humidity.  Linda turned off the air-conditioning and we opened up the house for the first time in a week.  We had a light breakfast of grapefruit and cinnamon raisin toast and then spent an hour enjoying our coffee.  I finished the little treatise on cryptology yesterday at Panera and started reading Oystein Ore’s “Invitation to Number Theory.”

Linda needed to make a quick grocery run for miso so I worked for a while on the sofa design, laying out the pieces that will be cut from a 48″ x 96″ sheet of 3/4″ plywood.  When she returned from her errand she went for her daily walk while it was still cool.  After her walk she made a cold black bean salad and then made roll up sandwiches using multigrain pita bread.  It was delicious and healthy; the bread alone had nine grams of protein.  After lunch Linda attended to some nutritional calculations related to the dinner she planned to fix and I gathered up the tools I thought we would need to take care of some things in the bus.  That included some small zip lock bags for small parts.

My first task was to remove the screws that secure the shorter head end of the bed platform to the foundation.  The platform is in two pieces joined by a piano (continuous) hinge.  After doing this I lifted the other end and was reminded that I had already disconnected the two gas springs that normally hold it open.  I also realized that the wires which supply 12VDC power to the two compartment lights on the underside of the platform were routed under a fixed cross member and cable-clamped to the other piece of the platform.  I already knew, or assumed, that they were hard-wired and had spade lug crimp connectors ready to go.

\With Linda’s help I was able to detach the wire loom at several points to create some slack.  The +12VDC wire was connected to a microswitch with a spade lug so it was easy to unplug.  I clipped the neutral wire, stripped both free ends, and attached an insulated male spade connector to one and an insulated female spade connector to the other.  With that the entire platform could now be removed from the bus to get it out of the way while we install the new floor tiles.

In the kitchen area of the bus we unscrewed and removed the walnut trim around the fixed window on the passenger side.  I reinstalled all of the screws so we would not misplace them while Linda took the trim to the garage to store it.  I removed the screws that held each of the three reading lights to underside of the upper cabinet in front of the fixed window.  They were wired with very clever little insulated terminal strips which made them easy to disconnect and will make them equally easy to reconnect.  Linda bagged each fixture and its parts separately in one gallon zip lock bags.

The AC light fixture was trickier to remove.  First I turned off the circuit breaker on the inverter sub-panel and verified that the light no longer came on.  By lifting the false bottom of the cabinet I could see that the fixture was installed onto a ceiling junction box.  That meant there was probably a post threaded into a cross bracket with the post protruding down through the center/mounting hole in the fixture and held in place by the decorative nut.

I was not able to turn the decorative nut by hand so I got the faucet wrench.    I have had this unique and specialized tool for a very long time.  It is designed to reach up behind a sink and grab the retaining nut on the underside of a faucet 12 inches away.  The head is spring loaded and flips over to allow the wrench to be used to tighten or loosen the nut.  Occasionally, like today, it finds an alternate use.  I like it when that happens.

\With the fixture loose I was able to color code the neutral wires with white tape, untwist the wire nuts, and then put the wire nuts back on the two supply wires.  Linda took the fixture to the garage and figured out way to store it safely using an unused waste basket.  We talked about the built-in sofa and some HVAC details for the passenger side of the cockpit before wrapping up our bus work for today.

While I put the tools away Linda started working on dinner.  Tonight’s special creation was vegan Pad Thai.  Regular Pad Thai was a favorite of ours for many years even after we switched to a vegetarian diet as we were still eating eggs.  The dish has a lot of ingredients, so it is a lot of work, and a good vegan version is a real challenge, but Linda executed the dish quite well.  We finished up the watermelon for dessert, which was sweet but light and refreshing.

I try to write every day while the sequence and details of the day’s events are still clear and my thoughts and feelings about them are somewhat “in the moment.”  But I don’t usually finish a post and upload it the same day.  I often finish it the next morning which means I have a chance to sleep on in it.  We have been so busy with the bus remodeling project that I have barely had time to write the drafts of my posts and I have not had the time to transfer them, edit them, select photos and post-process them, and upload everything to the blog.  I don’t like getting so far behind, but there are only so many hours in a day and I do need at least seven hours sleep a night.

After dinner I e-mailed Josh to see when we might get the extra fabric we ordered to make seat and back cushions for the sofa I am designing for the bus.  I then settled in to read about number theory before drifting off to sleep.

 

2015/07/29 (W) Drive Shaft

Leave a reply

I had had a 9:30 AM appointment at Brighton Honda to have a drive shaft replaced and suggested that we just continue on to the Brighton Panera a half mile down the road for bagels and coffee.  Linda never refuses to go to Panera so that is what we did.  The Wi-Fi was out of service but we both bought things to read so we did not care.  We sat in the two comfy armchairs by the fireplace, which was turned on, because the temperature inside was very cool, a frequent problem with this particular Panera store.  We each had a bagel and many refills of our coffee cups and stayed long enough that Brighton Honda called to let me know my car was ready to be picked up.  We left at 12:30 PM and Linda dropped me off to retrieve the ca.

Back home we had the leftover couscous with caramelized onions and the rest of the kiwis for lunch.  Linda finalized her grocery list and headed off in search of food.  I spent the rest of the day and most of the evening working on the design/drawings for the built-in sofa.

Through the course of the day I had QSOs with Jim (N8KUE) on the Novi 440 repeater and with Chris (K8VJ), Steve (N8AR), and Mike (W8XH) on the South Lyon 2m repeater. I also installed an updated driver for the NVIDIA GPU in my ASUS laptop, installed updates on the older Sony VAIO workstation (which still has Windows XP Pro), installed updates on the Linux box, and took time out for dinner (a delicious red lentil potato curry) and dessert (very sweet watermelon).

I went back to work in my office and sent an e-mail to Mike (W8XH) concerning Windows 10.  He replied via the South Lyon 2m repeater.  We had a long chat from 10:10 PM to just after 11 PM that was joined briefly by Steve (N8AR).  There was also a group QSO taking place on the Novi 440 repeater that I listened to in the background.  After I turned the radio off and came upstairs Linda said it appeared that my ham radio transmissions were interfering with our OTA TV signals.  The antennas are on the same tower but the OTA TV antenna is mounted below the Diamond X-50N 2m/70cm vertical ham antenna so I was a little surprised that it would be causing interference.  The vertical antenna has an omnidirectional radiation pattern which resembles a donut sitting on a horizontal surface, so the location directly under the base of the antenna should be a region with very little signal.  Apparently that is not the case and I will eventually have to do something to remedy the situation.  For now, however, the solution will be to not use the radio when someone s watching television.

 

2015/07/28 (T) Mighty Dremel

Leave a reply

I got up at 8 AM.  I must have been sleeping soundly as I was unaware until then that had already gotten up.  She had gone for a walk and left me a note.  The high temperature today is forecast to hit 90 degrees F and she wanted to get her walk in early.  I fed the cats and checked the mouse trap in the pantry.  We caught another one overnight so I carried the trap back to the northeast corner of the yard and released it.

I made our morning coffee and had just settled in to work on my iPad while it brewed when Linda returned from her walk at 8:35 AM.  We enjoyed our first cup of coffee and then had breakfast.  She made a batch of her fabulous granola yesterday but we have to finish the previous batch first.

Today was the day to get back to work on the bus.  First I spray lubed the two overhead garage doors, both rollers and section hinges, and ran them up and down and back up.  I needed to open them anyway to get out the ladder and tools and sometimes it’s better to spend an extra minute while you are thinking about something and just take care of it.  Besides, I had no way of knowing if I would accomplish anything else today so at least the doors worked more smoothly.

This is where the "stop block" was located. The left screw came out but the right one did not. I had to grind it off.

This is where the “stop block” was located. The left screw came out but the right one did not. I had to grind it off.

In a very real sense our entire bus remodeling project hinges on getting the old refrigerator out and the new refrigerator in.  The refrigerator swap, in turn, hinges on being able to open the fixed window panel on the passenger side of the bus.  That panel is hinged at the top by a pair of rolled channels, one on the top back edge of the window frame and the other on the lower back side of a rail that runs almost the entire length of the bus.  Most of the upper body side panels are hung from these rails and secured at the bottom with latches or other fixed hardware.

The window frame in question has two latches that can be released allowing the frame to swing open and provide an emergency exit, except for the two “stop blocks” in the upper outside corners which are attached to the frame (with two screws) just below the rail.  As the name suggests, these blocks appear to stop the frame from opening more than about 10 inches. That would make emergency escape difficult but it makes it impossible to remove a refrigerator.  We know these frames will open farther as someone posted a photo of an H3 on one of the Prevost bus websites with this same frame open almost 90 degrees (horizontal).

As I have described here before I successfully removed the left block and the left screw from the right block a couple of weeks ago but have been unable to remove the right screw from the right block.  Early in my attempt to remove it I stripped the Philips head and things just got worse from there.  I borrowed an impact screwdriver from Chuck, which successfully extracted the left screw but the right screw would not budge.  I eventually bought and used three different screw extractor sets and broke two drill bits using one of them.

The Dremel with a cutoff wheel installed. The stop block was unusable by the time I got it of.

The Dremel with a cutoff wheel installed. The stop block was unusable by the time I got it of.

I borrowed a soldering gun and Dremel Kit from Chuck on Saturday and finally got around to using them today.  The idea of the soldering gun was to heat the screw causing it to expand and then contract when it cooled.  This will sometimes cause screw threads to separate from tapped holes.  In this case the block was already turning relative to the shaft of the screw but the screw was not turning so I hoped the heat might free it from the threaded hole in the frame.  To find out, however, I needed to create a slot in the shaft that would accept a flat blade screwdriver, in particular the large bit that is part of Chuck’s impact screwdriver kit.  Enter the Dremel.

In order to create a wide enough slot I put two cutoff wheels on the arbor.  The block is at the top of the window frame so standing at the highest safe step of our 8-foot step ladder I was at a comfortable height for holding the Dremel vertically and cutting a horizontal slot.  The cutoff wheels are about the size of a quarter so the slot extended well beyond the screw head, or what was left of it, into the block.  Using the Dremel was a last resort and I knew that once I made that decision the block was going to get destroyed.

The Dremel cutoff wheels cut through the block, which is aluminum, very easily and did not have any trouble with screw or the broken drill bits.  The drill bits eventually loosened to where I was able to extract them with pliers.  I tried several different screwdrivers in my newly created slot but to no avail.  I sprayed WD-40 around the block and screw using paper towels to catch the overspray and clean up any runs.  I kept cutting the block until I was able to pry it off of what remained of the screw.  With less than a quarter inch of the shaft left I cut a slot in the end and tried to unscrew it but the tangs just broke off.  I tried unscrewing it with pliers but it would not budge.  The protruding stub would interfere with opening the frame 90 degrees so I used the Dremel with a cutoff wheel to grind the shaft down flush with the frame.

All the "stuff" I used to attack 25 cents worth of aluminum because of corrosion.

Some of the “stuff” I used to attack 25 cents worth of aluminum because of corrosion.

Linda came out to help at this point.  I repositioned the ladder and then we unlatched the frame on the inside.  Linda pushed it out while I supported it from outside.  It opened farther than it had before but we did not try to raise it to a horizontal position.  The frame/glass is very heavy and we did not want to risk having it come loose at the hinge. We closed the frame and latched it.  I took a few pictures and then put all of the tools away.  The weather was very warm and humid and that was enough outside work for today.

We had hummus, pita chips, and black grapes for lunch.  After lunch I spent a few minutes in my office checking e-mail and then typed up the minutes from our July SLAARC meeting.  I then started working on the design/drawings for the built-in sofa.

I have a very long list of things to do but the furniture design remains a priority as I need to make sure Jarel has all the information he needs to keep moving forward on the custom cabinetry.  Although I will be assembling the sofa Jarel will be cutting all of the pieces.  I will be using a long rip of a full sheet of plywood and a long piece of 3/4 x 3/4 walnut hardwood as an edge band for the horizontal platform.  In order to give Jarel a cut sheet I needed to design the unit.  I also needed to design it so I knew it would fit when assembled.

I took an occasional break to chat with friends on the two local ham radio repeaters that we tend to use but otherwise stayed on task until late afternoon.  I had pulled a book on cryptology from our personal library and started reading it.  I took a nap before dinner and continued reading afterwards.  Fascinating stuff, cryptology.

 

2015/07/27 (M) Finish Drawings

Leave a reply

I got up at 7:25 AM and fed the cats.  There was a very large tom turkey feeding in the back yard by the basement walkout and just far enough out from the house that I could see him from the dining room doorwall where we keep the cats’ food dishes.  He walked up the west slope and then cautiously headed for our lower deck.  I kept an unseen eye on him from the kitchen corner window as he headed east towards the main deck.  I thought he might have spotted Linda’s tomato and herb planters but he kept on going.  Perhaps he caught sight of Jasper, or me, or his own reflection but something spooked him and he trotted to the east end of the deck.  He had Jasper’s full, undivided attention by this point and just walked around until he decided to walk down the stairs into the east yard and around the east end of the house.  I lost sight of him after that but we have seen turkeys feeding on that end of the house before and they have ready access to dense, protective cover from there.  I suspect this is the same lone tom that we have seen feeding in Cory’s yard across the street.

I sat and played games for a while and then started working on this post at 8:15 AM.  At 8:30 I caught a glimpse of a deer crossing the road into our yard by the main driveway but could not get up to get a better view as Juniper had settled in in my lap.  Linda got up around that same time having finally gotten a good night’s sleep.  I got dressed and made coffee.  We finally had breakfast at 10 AM.

My initial focus for today was to finish the drawings for the pull-out pantry, design/draw the cover for the front half of the passenger side HVAC duct and wiring chase, and design/draw the small cover that will connect the chase cover to the left side of the left desk pedestal base and hide the heater hoses.  I took occasional breaks to chat with friends on the South Lyon 2m repeater and finished my drawings at 4:30 PM.

Linda located a FedEx Office location in Brighton so I drove there instead of to the one in Novi to make copies and buy a mailing tube.  The copies did not come out as well as at the other office so I rolled up the originals and put them in the tube.  I checked to see what it would cost to have FedEx deliver the tube.  Their cheapest method was going to cost $28 and take three days to get there so I went across the street to the post office and mailed them to Jarel in Logansport, Indiana it for $2.94.  It will be there by Thursday and may get there by Wednesday.

When I got home I e-mailed Jarel to let him know the drawings were on the way.  Linda then reheated various leftovers for dinner.  I had started the day with an ambitious list of things I wanted to accomplish but by the time we were done with dinner I decided I had accomplished enough for the day and took an uncharacteristic nap.  I had just woken up when Butch called and we chatted about buses for a bit.  We turned in earlier than usual and watched Antiques Roadshow and the concluding episode of Ken Burn’s “The Dust Bowl” on the Detroit PBS station.

 

2015/07/26 (N) Rearranging

Leave a reply

I was up at 8 AM but did not make coffee as Linda was still asleep and the grinder is fairly noisy.  I put the last load of laundry in the washing machine, cleaned the litter tray (which we keep in the downstairs shower), and then worked in my office.  Jasper (the cat) came down to assist me but mostly ended up supervising.

All three monitors mounted in the ham shack using the ZioTek wall-mounted track system. The Dell is in the middle. There is a mount and room for one more monitor at the right end.

All three monitors mounted in the ham shack using the ZioTek wall-mounted track system. The Dell is in the middle. There is a mount and room for one more monitor at the right end.

I mounted the fourth (last) arm on the wall-mounted rail in our ham shack.  I swung it back against the wall to get it out of the way as I do not have a monitor that I want to install at that position at the moment.  I cleaned up the tools and staged them by the stairs and then moved the coiled coax out of the way and cleared a few things off of the desks so I could move the desks back into position.  I left them farther out from the wall than before so they were appropriately placed relative to the three wall-mounted monitors.  I then put various pieces of ham radio equipment back on the desks.

Monitors obviously need computers.  I removed the Dell Precision laptop from my computer desks, removed the computer from the combination docking station and monitor stand, cleaned all of the pieces, and reassembled it.  I set it at the left edge of the ham desks, slid it under the left monitor, and placed our old Icom IC-706 HF transceiver on the monitor platform, just for appearance sake.  We are not using thus radio at the moment but it fit nicely in that spot.

I placed the GoBox with the Icom IC-7000 HF/VHF/UHF transceiver and 12VDC power supply at the right edge of the desks, put the MFJ-998 Intelli-Tuner to its left (under the right monitor), and put the larger variable voltage DC power supply on top of it.  The time we spent yesterday determining where to mount the rail on the wall was time well spent.  The monitors are at a comfortable height for viewing when seated at the desk, tilted down slightly to avoid glare from the overhead down lights, and the bottom edges are high enough above the desk to permit sizeable equipment to slide under them.  The desks are also far enough out from the wall to make it easy to attach and manage cables.

I rearranged my primary ASUS laptop on my computer desks and checked my e-mail accounts.  I have had a discussion going on this past week with Gary at Bus Conversion Magazine about hats with the BCM logo and responded to a couple more of those communiques.  Around 10:15 AM I heard footsteps and knew that Linda was finally up so I wrapped up the work in my office, transferred the laundry to the dryer, and went upstairs.

Linda was working at her desk and was not hungry but wanted coffee.  She did not sleep well last night so I made a pot of Sumatra Manhelding which is NOT one of our half decaffeinated blends.  I got myself a bowl of granola and had a large glass of orange juice.  We spent the rest of the morning in the living room reading, writing, and menu planning.

The dinette area of our bus with the two fan-coil heat exchangers on the floor. They will go in the bases of the desk when it is installed in this corner.

The dinette area of our bus with the two fan-coil heat exchangers on the floor. They will go in the bases of the desk when it is installed in this corner.

I like to hear the grandfather clock strike 12.   Besides the charming Westminster chimes, it serves to announce that the part of the day has arrived where I am supposed to get some of the physical work on my to-do list accomplished.  Today, however, my #1 priority was to redesign the pull-out pantry so I limited my physical work to gathering up my tools from the basement and moving them to the garage, moving the bus back to its normal parking spot, and taking photos of cabinet details in the bus for Jarel.  I mixed in a little e-mail, a few computer updates, some ham radio, and time for meals, but basically I worked at my drafting board most of the day and evening.

For dinner Linda made a very tasty dish that we had not had before.  The base ingredient was rice and she used basmati even though the recipe called for brown.  I prefer basmati rice to brown rice so it was a good substitution as far as I was concerned.  The other ingredients were garlic, power greens, mushrooms, and blanched fresh green beans.  She sliced and caramelized a large onion and used it as a topping.  This was essentially a “1-pot” dish in that all of the ingredients ended up combined prior to serving.  Linda makes a lot of dishes like this and we both like them. This particular dish had the crunch of the green beans, the chewiness of the rice, and the soft earthy character of the mushrooms held together by the garlic and olive oil and topped with sweet earthiness of the caramelized onions.

At 8 PM local (EDT) I participated in the weekly SLAARC Info Net for the first time in a couple of years and did so from the comfort of our ham shack.  It was a pleasure using our new Yaesu FTM-400DR/DE dual band transceiver with our Diamond X-50N 2m/70cm antenna at a height of 40 feet and connected by good coaxial cables all the way through.  Club president Harvey (AC8NO) served as net control operator and did a nice job.

After the net wrapped up at 8:45 PM Steve (N8AR), Andy (N8DEV), and I chatted for another 20 minutes trying to find some rhyme or reason why our Yaesu FTM-400’s are experiencing random audio dropouts.  We did not get it figured out and wrapped up our QSO so Steve and I could check into the LARK (Livingston Amateur Radio Klub) net that started at 9 PM (EDT).  This was the first time I had checked in to this particular net even though LARK is based in Howell and the repeater is closer to us than the ones in South Lyon or Novi.

The LARK Net was much briefer than the SLAARC net and concluded at 9:16 EDT.  Steve and I went back to the South Lyon repeater where Paul (N8BHT) heard us and joined the conversation.  When we finally wrapped up our testing QSO I went back to work on my pull-out pantry drawings.  I was about to shut everything down at 10:45 PM EDT when Mike (W8XH) announced his presence on the South Lyon repeater.  He was mobile but full-quieting and I did not experience any dropouts during our 25 minute QSO.  I took a few minutes to e-mail Jarel and then called it a night.  I had a few almonds as a snack, got ready for bed, and worked on this bog post for a while.

 

2015/07/25 (S) Monitoring

Leave a reply

We started our day with our weekly ham radio breakfast in South Lyon.  As we were leaving breakfast I called Chuck to see if he was at his shop.  He wasn’t but said he could be there between 11 and 11:30 AM.  We drove home, loaded up my car with the accumulated recyclables, headed over to Recycle Livingston, and then headed to Chuck’s shop in Novi.  We arrived before he did and let ourselves in.  I got his Dremel tool kit and pistol style soldering gun and we chatted for a while.  He had a noon appointment with someone at a commercial building he owns in Livonia, and we had a long list of project tasks to take care of, so it was a shorter chat than usual.  We stopped at the Lowe’s in New Hudson and bought a can of garage door spray lube and then headed home, stopping for fuel at the Brighton Shell station on Grand River Avenue at I-96.

At our ham radio breakfast Linda had rye toast and I had an English muffin for breakfast (our usual meals) so we were hungry by the time we got home.  We had roll up sandwiches of hummus, Vidalia onions, and greens with a drizzle of olive in a whole wheat pita.  Very tasty.  We then got to work installing the wall-mounted track for the ZioTek monitor mounting system I bought from CyberGuys.

The north wall of the ham shack. Critical points for the mounting of the ZioTek track system are marked with green tape.

The north wall of the ham shack. Critical points for the mounting of the ZioTek track system are marked with green tape.

Conceptually the installation was simple but it took all afternoon.  There is a kind of alcove at the north end of my office that serves as our amateur radio (ham) shack.  The purpose of the ZioTek system is to support up to four monitors on the north wall above the two desks located there so that they are not attached to the desks or using up any of the desktop real estate.  The walls in the office are 7/16ths inch thick T-111 exterior plywood with 1/2″ grooves on 4″ centers running the length of the plywood sheets.  The sheets are installed vertically so the groves run vertically giving the appearance of vertically installed 4″ wide rough sawn boards.  We finished the photo studio/office at the old house with this material so we knew we liked the way it looks.  Being plywood it has once major advantage and one major disadvantage compared to drywall; you can screw relatively heavy things to it, but holes are essentially impossible to repair.  What that meant for us was that we only had one chance to get the track in the correct location.

In this case “correct” meant:  at the right height and horizontal location to be able to position the monitors exactly where we wanted them while making sure the track was level.  To accomplish this I bought a 1″x6″-8′ poplar board to use as a mounting plate for the two track sections.  (All of the trim in the ham shack/office is poplar.)  We used pieces of tape to mark the locations of the corners of the three monitors on the wall and marked the centers of the VESA 100×100 mounting plates.  When we knew where the horizontal centerline of the tracks needed to be we determined the horizontal location of the tracks relative to the right end of the poplar board, which would be installed flush to the vertical trim in the northeast corner of the alcove.

The ZioTek tracks will mount to the horizontal poplar board which will be mounted to the wall at the studs.

The ZioTek tracks will mount to the horizontal poplar board which will be mounted to the wall at the studs.

We set the poplar board in the utility hallway and positioned the two tracks on it.  I butted the tracks together and slid one of the mounting plates so it saddled both tracks and kept them aligned.  The tracks are 4.5″ wide and the board was 5.5″ wide so I very carefully positioned the tracks for a 1/2″ reveal along both edges.  I then marked the eight mounting holes (four in each track) and removed the tracks.  Using a brad point wood bit that was slightly smaller than the central shaft of a #14 wood screw I drilled holes that were as carefully centered as I could make them.

We held the board in position against the wall and used a 1.5″ #6 finishing nail through the right mounting hole to hold that end of the board.  We then used a 4-foot level on the top edge of the board and secured the left end with a second nail through one of the mounting holes.  We positioned the chair where it will be when in use and made sure we liked the height of the board.  It looked and felt right so we proceeded to secure it to the wall.

The ZioTek tracks mounted to the poplar board mounted to the wall. Linda is vacuuming up sawdust from drilling.

The ZioTek tracks mounted to the poplar board mounted to the wall. Linda is vacuuming up sawdust from drilling.

Using a small carpenter’s square I marked locations for mounting screws one inch in from each edge of the board in vertical alignment with the small heads of the nails that secure the T-111 to the studs.  The 8-foot long board spanned six studs so I had 12 holes to drill.  I used a standard drill bit that was slightly smaller than the shaft of a #14 wood screw and drilled through the poplar board, through the T-111, and into the studs.   I used a countersink bit to create recessed pockets for the flathead wood screws.  We then secured the board using 3″ long #14 flathead wood screws.  We applied a little soap to the screw threads to help them go in.

I pulled the two small nails out of the track mounting holes.  Using the same drill bit I finished drilling out the mounting holes all the way through the T-111.  We positioned and partially installed one track using 2″ long #14 flathead wood screws in the two end mounting holes.  We then did the same thing with the other track.  I slid one of the mounts so that half of it was in each track and partially installed the remaining four screws.  I gently snugged up all eight screws, checking the track alignment as I went, and then torqued them down.  The heads stick up above the inside surface of the track but the shuttle mounts are raised on the underside so they slide right over the screw heads without interference.

The first of three monitors to get mounted. This one is on the left end of the tracks.

The first of three monitors to get mounted. This one is on the left end of the tracks.

With the track mounted to the wall we turned our attention to installing the monitor mounting arms and monitors.  We used one of the long arms on the left, the short arm in the center, and the medium arm on the right.  The other long arm will eventually end up on the far right or get swapped for the medium arm, but for now I only wanted to mount three monitors.  We installed the nice Dell monitor that goes with my older Dell Precision laptop in the center and installed the two ASUS monitors to either side of it.

By the time we got the third monitor mounted the office was in more disarray than usual and we did not have time to clean up tools and put things back in order.  Linda did manage, however, to run the vacuum cleaner and get most of the sawdust and wood chips sucked up.  Our son had called during the afternoon with a last minute request for babysitting services from Linda and I decided to go too.

A view of the mounts for the left and center monitors. This is a substantial system.

A view of the mounts for the left and center monitors. This is a substantial system.

We left at 6 PM for Ann Arbor and stopped at the Whole Foods Market to pick up a few things for dinner.  We got two different vegan sushi rolls, a cold couscous salad, and some organic black grapes.  When we arrived at Brendan and Shawna’s house a little before 7 PM Madeline was surprised and excited to see us.  Brendan and Shawna left around 7:15 PM for an engagement party and Madeline was fine with the whole thing.  She was still eating her blueberries and strawberries and then wanted Linda to read several books to her.  We went upstairs to see how her crib had been converted to a toddler bed, allowing her to get up during the night to use the bathroom.  Such a big girl.  But not too big for pajamas that featured fairies.

After another couple of stories Madeline went to bed without a fuss.  We then had dinner.  The California rolls were OK but the couscous salad was outstanding and the grapes were very good.  We sat on the couch using our iPads but I could not stay awake so I laid down and drifted off to sleep.  I was awakened about 90 minutes later by the return of Madeline’s parents.  Linda gathered up our leftover food and the roses the kids had gotten her as a “thank you” for babysitting on such short notice which gave me time to fully wake up.  We were on our way by 10:30 PM and back home shortly after 11.

 

2015/07/24 (F) Open and Shut

Leave a reply

I was up at 7:30 AM and made coffee but I did not see Mara or Linda until after 9 AM.  Around 9 AM I heard a knock at the front library doorwalls and heard someone saying “hello?,  hello?, David?”  I went out the front door and saw the front end of a red Ford Focus parked in front of our bus.  I had never met this guy but he was not unexpected and I knew he was looking for David LaVoisne, who lived here with his wife, Maria, until we bought the house from them in February 2013.  I knew this guy might stop by as he had once before when we were away and chatted briefly with our lawn care guy, Keith.  I also knew that he had worked with David at the Ford Wixom plant before they retired.

We introduced ourselves and had a nice chat.  I explained that David and Maria had sold the house and their Airstream motorhome, bought a newer motorhome, and were now full-time RVers.  (As I recall they bought a used Foretravel.)  Apparently they did not let all of their friends or former colleagues know what they were doing.  I also mentioned that they had moved the few possessions they did not get rid of to their son’s house somewhere in the region and that they probably visited there occasionally.

Mara emerged about the time our visitor left.  Unfortunately I do not recall his name.  We all had breakfast together after which Mara went about her final departure preparations.  She gave Linda a small fir tree and two small herbs.  Linda transferred the herbs to her herb pots and gave Mara’s small pots back.  She needed to top off her fresh water tank so I helped with that.  The lock on the water fill door stuck in the open position so Mara got her can of dry lube and I sprayed a little in the lock by holding the protective cover open with the tip of the key.  That did the trick, another quick fix to a small but potentially annoying problem.

When her rig was basically ready to go Mara made one last use of the shower, got dressed to travel, unplugged the power cord and stowed it away, and pulled in the slides.  After hugs all around she climbed into the pilot’s seat and fired up the engine and Sabra (one of her two cats) climbed up on the dash just in front of the steering wheel.  I guided her as she backed out onto our road.  She drove down to the court, did a three point turn, and a few minutes later drove past our house in the opposite direction, back on the road again after almost two weeks at our place.  It was noon, but she was only going as far as London, Ontario today.  Linda got a text message later letting us know that she had arrived at the Moose Lodge and the border crossing on the Blue Water Bridge from Port Huron, Michigan to Sarnia, Ontario had only taken 30 minutes.

After Mara was out of sight I gathered up the laundry, sorted it, and started a load of warm whites.  I wrote out a list of parts I needed to finish the garage door opener installation and the monitor mounting system in the ham shack and then drove to Lowe’s in Howell.

I was back home by 1:30 PM and we had hummus and chips along with black grapes for lunch.  We started working on the garage door opener installation when my phone signaled that I had a voice message.  It turned out that I had one on the house phone too.  Both messages were from Jarel.  He had a few questions about dimensions on one of desk drawings so I called him back and we sorted that out.  He retrieved the half sheet of walnut veneer plywood from Butch last night and bought 16 board feet of walnut.

In spite of the 85 degree temperature and what felt like high humidity, even though it was only 41%, we worked for about three hours and finished installing the opener on the small garage door.  It was quite an involved process but it worked when we were done.  The new opener has automatic reverse if it encounters an obstruction and an infrared sensor beam about 6″ off the floor.

At 5:30 PM we loaded the old garage door opener into the dump trailer.  We then loaded the old OTA TV antenna pieces.  Brad is picking up the trailer in the morning so we will not fill it but it we put the junk in it that we needed to get out of the garage and a few other things as well.

We took a break around 6 PM to have some water and get off our feet for a while.  At 6:45 PM Linda made salads and cooked up some vegan Italian sausages.  After dinner we planned to work for a while in the ham shack on the installation of the wall-mounted track system but we were too tired to start a project that was going to require decisions and careful attention to detail.  We sat in the living room instead and used our iPads for the usual things.  It was great having Mara here and we look forward to her return someday.  But for now she is off on the next leg of her open-ended adventure and we have a lot of work yet to do to get our bus ready for the 2015-16 winter season.

 

2015/07/23 (R) Wrapping Up Mara

Leave a reply

Mara’s plan was to make this the last full day of her visit.  Our day started without her as we had cinnamon raisin toast, juice, and coffee for breakfast.  I got a call from Jarel with clarifying questions and ideas about the desk and the pull-out pantry.  After a thorough discussion we had better ways to approach a few things.  He also had a better feeling for the estimated cost of the project and I agreed to send him 50% as a deposit.

I typed up a short letter and printed off the graph that Steve made of the return loss for the M-302N V/U lightning arrestor.  I packed the unit for shipping to Morgan Manufacturing and included the letter and graph.  Linda wrote out the check for Jarel and got it in an envelope to mail.  She then went to the library, Post Office, and Humane Society where she donated cat and dog paraphernalia that we had accumulated over the years.

While Linda was gone I worked in the bus for a while and Mara worked on travel preparations.  I started by removing the old 3/4″ plywood floor from the refrigerator alcove.  The original plywood bus floor appeared to mostly be in good condition but I will put a new secondary floor in the alcove to keep the refrigerator legs above the level of the new tile floor.  There are a LOT of wires running along the floor of the alcove at the back wall and I may fashion a cover for them and seal up the holes at either end.

I removed the AC dimmer for the living room lights and the DPDT momentary contact DC switch from the floor-mounted walnut box where they were installed.  The DC switch controlled the passenger side sofa footrest.  I had to remove the wires from both switches to get them out.  The AC dimmer was easy but the DC switch had four different color wires with spade connectors.  I made careful note of which terminal each color went to and then pulled the spade connectors off.  With the switches out I was able to remove the box and its mounting cleats from the floor and wall.  This area will be tiled and the box will not be reused.

Out of curiosity I tested the switch with an Ohm meter to see how the terminals were connected internally.  I also checked the wires with a DC volt meter to see how they were being used.  Two of the wires were +12VDC and DC ground and the other two went to a connector that was originally plugged into the footrest.  The switch applied 12VDC to the two load wires in one position and reversed the polarity in the other position, making the footrest go out or in respectively.

Last year I had removed two blank outlet covers on the walnut panel next to the co-pilot seat so I knew that these two switches were originally installed there and subsequently moved to the floor-mounted box.  I unscrewed the 1/4″ walnut veneered plywood panel from the wall to see what was behind it.  What I found was a LOT of wires and it was not a pretty sight.  I re-installed the two switches in their original locations and re-routed some other wires so they went up over the HVAC chase.

There was still a large bundle of wires running along the floor at the base of the HVAC chase that I needed to re-route but I decided not to mess with those today.  They are connected to four different switches and a doorbell and disconnecting everything was going to require careful attention to detail.  I pondered the refrigerator some more and decided there wasn’t anything else I could do with it for now and that I was done working in the bus for today.

There is too much to do at the moment to just sit around so I decided to install the new garage door opener for the small garage door.  New is relative; it has been sitting in the garage in its original packaging since we moved into the house, supplied by the previous owners.  The old one has not worked correctly since we moved in and the previous owners bought the new one but ran out of time to install it.  It turned out to be rather more complicated than I expected, with very comprehensive assembly and installation instructions.  It also turned out to be a two-person project so Linda worked on it with me.

We were working and Mara had started prepping dinner when a UPS truck showed up with four boxes.  The delivery included:  Mara’s refrigerator vent cover; the Cutco knives and scissors, and; the ZioTek track system for wall-mounting the monitors in the ham shack (2 boxes).  The vent cover was due for delivery today but the knives were not due until tomorrow, so we were really glad to see them as two of them were for Mara.  The monitor mounting system was also due for delivery today but I had temporarily forgotten about it.

The north wall of the ham shack/office. This is where the ZioTek wall-mounted monitor mounting system will go.

The north wall of the ham shack/office. This is where the ZioTek wall-mounted monitor mounting system will go.

Mara was understandably anxious to see if the vent cover fit her base properly.  It was a VentMate and appeared to be identical to the old one.  She climbed up the ladder on the back of her motorhome and I handed parts and tools up to her.  I then climbed up was well.  She removed the old cover and we set the new one in place.  It was a perfect fit!  We put a small amount of putty under each screw head and then ran them down snug and congratulated ourselves on another job completed and well done.

With Linda’s help we put Mara’s kayak back in its custom carrier which fits in the receiver on the back of her motorhome (she does not tow a car).  The carrier was built by a welding shop in Mesa, Arizona to Mara’s specifications and is made from 2″ square tubular steel and powder-coated black.  The carrier holds the kayak diagonally across the back of the motorhome from lower left (driver’s side) to upper right.  The nose of the kayak sits in a pocket near the driver side rear corner of the motorhome and the midpoint is nestled in a much larger cradle.  A strap runs from the nose pocket up to the midpoint on one side and across the kayak to the other side where it is attached to a ratchet and has a hook on the end.  With the hook engaged in a ring the strap is ratcheted tight and the kayak is secure for travel.  Mara runs an anti-theft cable through an eyelet near the nose and attaches a lock for safe keeping.  The tail sticks up higher than the top of the roof-mounted air-conditioner covers but does not extend beyond the passenger side wall.  The tip of the kayak is 13′ 2″ from the ground.

We made good progress on the garage door opener but had to stop at the point where we needed to attach the motor housing to the ceiling as I needed to get some parts (angle iron and lag screws) that did not come with the unit.  The front of the track was attached to the header above the door opening and we left the motor assembly resting on top of a 6 foot stepladder.

The pieces of the ZioTek monitor mounting system laid out on the floor of the ham shack/office.

The pieces of the ZioTek monitor mounting system laid out on the floor of the ham shack/office.

While Mara and Linda prepared dinner I unboxed all of the monitor mounting components.  I was curious to see the parts and wanted to make sure everything was there and undamaged, which was the case.

Dinner was Thai vegan spring rolls in rice flour wrappers.  The prep work was in the cutting of lots of veggies (carrots, zucchini, onions, red and yellow peppers, Chinese cabbage, and mushrooms).  Mara made two dipping sauces, one with ginger, hot peppers, and other things and one based on fish sauce (so we passed on that).  Linda selected our bottle of Malvasia Bianco wine from the Heart of the Desert winery in Alamogordo, NM.  It was white, which we thought would go well with the delicate spring rolls, but very sweet with a slightly thick mouthfeel, like a late harvest Riesling or a Sauternes.  Perhaps not the best choice, but we finished the whole bottle anyway.

We chatted for a while after dinner but like most of our evening meals dinner was a drawn out affair with lots of conversation.  Everyone was tired and the women turned in for the night.  I went to my office and answered e-mails from Gary at BCM that I had seen earlier in the day.  I then went to bed and tried to catch up on blog posts for the last few days but could not stay awake long enough to finish them.

 

2015/07/22 (W) Chucking Junk

Leave a reply

After our usual breakfast and coffee we sat for a while in the living room.  This is part of our morning routine and I often use the time to finish up my blog post from the previous day but the last couple of weeks we have been busy and I have not always had time.  We enjoyed the time until about 9 AM and then got serious about loading our “junk” into the Chuck It Junk Removal dump trailer.

Our bus refrigerator with the doors off in preparation for removing it from the coach.

Our bus refrigerator with the doors off in preparation for removing it from the coach.

Mara checked with Cummins Bridgeway and they told her to bring her motorhome in at 11 AM so she broke camp at 10 AM and backed out of the driveway at 10:15 AM.  Cummins Bridgeway put several technicians and mechanics to work on her rig to re-install the genset, install new shock absorbers, and service the transmission (filter and fluid).  She was out in a few hours and stopped at General RV to return the Camco refrigerator vent cover which did not fit her base on the roof.

The Chuck It Junk Removal dumpster trailer with some of our stuff in it.

The Chuck It Junk Removal dumpster trailer with some of our stuff in it.

We took a break from chucking junk and extracted the old refrigerator from its alcove in the bus, which was a 2-person job.  I got some scraps of 1/2″ plywood to set in front of the elevated alcove base as I did not want to walk or slide the unit across the bus sub-floor, especially with the residual thinset mortar.  First we had to walk it out a few inches which was hard because it only had 3/8″ clearance on each side.  Once it was out far enough we were able to open the doors enough to remove all of the shelves and bins, which Linda took into the house and garage.  I then disconnected the water and electric that ran up into the left (freezer) door at the bottom hinge corner for the ice/water dispenser and light.  With those disconnected and pulled out of the bottom of the case we unscrewed the bottom and top hinges and removed the two doors.  Linda collected all of the small loose parts as we went and put them in a plastic container as we knew we would have to reassemble the unit at some point.

The doors had 1/4″ walnut veneer plywood face panels and we wanted to salvage those to use with the new pull-out pantry.  Normally you just remove the handle trim from the edge of the door and slide the panel out.  The fridge door panel would not budge so we removed the trim from all four edges of the door.  The panel had been stuck in place with strips of double-sided tape so we carefully peeled it loose.  The freezer door had two smaller panels, above and below the ice/water dispenser, and they slide out easily after removing the handle trim.  We carried the doors, trim, and panels to the garage and then walked the case completely out of the alcove.

The shelf I built for one of the storage bays on Mara's Fleetwood Bounder.

The shelf I built for one of the storage bays on Mara’s Fleetwood Bounder.

I spent some time pondering what would be required to disassemble the refrigerator enough to get it out through the door of the bus but decided not to do anything until I had talked to Butch.  Just before dinner I had a long chat with Chuck about the refrigerator swap and he reminded me that DTE Energy (the electric power utility for this region) will pick up old refrigerators and freezers and pay you $50 for them.  Linda checked this out online and learned that they have to be plugged in and operating or they won’t take them, so we have a double incentive for getting it out in one, operating piece.

Our revised plan is still to get the case out in one functioning piece through the side window frame but it won’t be this weekend.  The guy with the sunroom business in the building in front of Chuck’s shop is still in the process of moving to his new place and has trucks, cars, people, and junk all over the place making ingress/egress to Chuck’s shop difficult to impossible.  The business is supposed to be gone by the end of the month so we will wait another week and plan for Saturday August 1st assuming I can get the window frame open.  In the meantime I need to get back to work on the bus floor, so I will have to spend part of next week sanding and start installing the 1/4″ underlayment for the new vinyl tile.

Mara in our home kitchen with her wonderful pizza. This thing was truly good eats.

Mara in our home kitchen with her wonderful pizza. This thing was truly good eats.

Mara and Linda made another pizza for dinner and it was every bit as good as the first one.  Mara has been a wonderful house guest.  We have left the house open to her and she has made herself comfortable in the kitchen and using the hall bathroom and laundry.  It helps that Linda is not possessive about the kitchen.  Whenever we have visitors who want to help in the kitchen Linda welcomes their participation.  It’s been fun for both of them and they have each learned a few knew things and deepened their friendship.

 

 

2015/07/21 (T) A Long Day

Leave a reply

I was awake at 6 AM, and up shortly thereafter, even though I did not set an alarm.  I packed a change of clothes and a few toiletries and then gathered up my cell phone and iPad chargers, my iPad, and my checkbook.  I loaded the desk/pantry drawings and travel bag into my car and then did a temporary installation of the weBoost cellular booster.  I put the outside magnetic base antenna in the center of the roof and experimented with the placement of the inside antenna, eventually setting it above the passenger side sun visor facing down.  I backed out of the driveway at 7:05 AM and headed for Indiana.

I took Hacker to Golf Club to Latson with some thought of stopping at Teeko’s for coffee but decided to get some miles behind me first and proceeded to I-96 westbound towards Lansing.  I should have looked up the frequency for the Lansing area repeater, where Don runs a net Monday through Friday from 7 AM until at least 11 AM, but I didn’t think of that ahead of time.  I would also have had to figure out how to switch Mike’s Icom IC-2820H radio from memory mode to VFO mode.  Eventually I will, but not today.  Today was not about ham radio, it was about bus projects.

I took the Lansing Road cutoff to I-69 south and about 20 miles later took the Lansing Road exit at Charlotte.  I stopped at the Biggby’s Coffee not far from the highway and resumed my trip around 8:30 AM.  When Linda and I drove to Edwardsburg, Michigan to visit Coach Supply Direct on July 1st we discovered that M-60 was closed at Minden (between I-69 and US-131) and had to take a long detour.  Rather than risk having that happen again I headed west on I-94.  I had been playing with the cell phone booster but unplugged it and plugged in the Garmin 465T GPS instead.  I eventually saw that M-40 came all the way north to I-94 and decided to take it instead of US-131.

I had never been on this stretch of M-40.  The road was a good 2-lane at 55 MPH except going through small towns.  I drove through miles and miles of vineyards and eventually got to the charming (looking) little town of Marcellus where I discovered a large Welch’s plant.  I knew that a lot of the grapes grown in southwest Michigan ended up as Welch’s grape juice but I did not know where their processing plants were located.  Now I know where they have at least one.

When I reached the intersection with M-60 in Jones I stopped at the Shell station for fuel.  Regular unleaded was $2.52 per gallon which was better than I had seen so far during the trip.  Instead of continuing down M-40 to US-12 I put the address for Coach Supply Direct into my GPS and headed west on M-60 towards Cassopolis.  The GPS had me bypass Cassopolis by heading south on Calvin Center Road to Brownsville Road and then west to M-62 where I headed south towards Edwardsburg.

When I arrived at Coach Supply Direct it was locked up with no sign of Josh.  I called his 800 number and he answered, which I appreciated.  He was in western Pennsylvania heading home from a customer service call and said he could meet me at the shop after 4 PM.  We agreed that I would call him when I had a clearer picture of what time I could get back to his shop.

I left Edwardsburg and drove back on US-12 to Cassopolis Road which merges briefly with Old-102 and then becomes IN-19 (SR-19) in Indiana.  I stopped at Factory RV Surplus in Elkhart, which is on SR-19, to buy a special two-piece bracket for mounting the edge of a table to a wall.  I saw it on their website and luckily they had it in the store as well.

I proceeded south on SR-19 to US-20, went west to US-31, and took that south to the SR-25 exit at Rochester.  From there it was 22 miles to Logansport and a few more blocks to Jarel Beatty Cabinetry.  Jarel is a cabinet maker and a mutual friend of Butch Williams.  I have been talking to Jarel about the custom desk we wanted for the bus for several years and, more recently, about the pull-out pantry and HVAC duct and wiring chase cover.  The purpose of my visit was to deliver the design drawings for the desk and pantry and go over them with Jarel.  I got there around 1:20 PM and left around 5:50 PM.  After discussing the projects at length we agreed that I would change the design of the pantry so I did not leave those drawings with Jarel.  The Fulterer pantry slide had been delivered to Jarel so I took that with me as it turned out to be too wide for this project.

I set my GPS destination for Edwardsburg and it indicated I would arrive around 7:45 PM.  I called Josh to see if that would work for him and he said it would.  I headed north on SR-25 and then called Butch to let him know that I would not be able to stop and visit or spend the night.  That was probably just as well as he was in the emergency room when I called.  He had nicked his thumb in his table saw and was having it tended to.  I stopped at the Kroger in Rochester to buy some snacks for dinner and got a return call from Butch.

The drive to Edwardsburg was pleasant and took me on some more roads I had not driven before.  US-31 north to US-20 east was familiar territory but I exited at Elm Street (US-331 north) which bypassed the west side of Mishawaka and eventually took me up through Granger and onto M-62 in Michigan.  A few miles later I was at Coach Supply Direct in Edwardsburg where Josh was waiting for me.

I returned the Lambright Comfort Chair fabric samples and the MCD shade material samples (the reason for my visit) and we chatted for about 45 minutes.  Our new MCD shades had already arrived but I asked Josh to hang on to them.  We tentatively agreed that we would bring the coach to his shop on Monday September 14 to have the new chairs and shades installed.  The GLCC Surplus and Salvage Rally starts on Wednesday the 16th in Elkhart and Josh offered to let us park at his shop the evenings of the 14th and 15th with 30A electric.

I left around 8:30 PM and started for home.  Again, the initial route was familiar as I took US-12 east to M-40 north, to M-60 and stopped at the Shell station in Jones for the second time today.  I then travelled east on M-60 to Three Rivers where I picked up US-131 northbound.  Rather than continue east on M-60, which I presumed was still closed at Minden, I stayed on US-131 all the way to I-94 between Kalamazoo and Battle Creek.  On I-94 east I encountered a major traffic jam due to construction.  The highway was down to one lane and traffic was barely moving as people merged down and then gawked as they went past the very busy construction site.

The rest of the drive was uneventful and familiar as I left I-94 for I-69 north, stopped at the McDonald’s in Charlotte for coffee, and got back on I-69.  I took the Lansing Road cutoff to I-96 and rolled along eastbound to the M-59 exit on the far west edge of Howell.  Eleven miles on M-59 put me at Hacker Road and a few miles later I pulled into the driveway.  It was just after midnight when I arrived, about 17 hours from when I left, and I had put over 550 miles on the car.  I unloaded a few things from the car and then went straight to bed.

 

2015/07/20 (M) Chuck It

Leave a reply

Our morning got busy right away.  We had breakfast and I made coffee while Linda entertained Madeline.  Brad, from Chuck It Junk Removal, dropped off the dumpster trailer at 9 AM.  Keith, from Kish Lawn Care, showed up at 9:30 to cut the grass.  Linda took Madeline to the Mill Pond to use the playscape and Mara started scrapping old caulk and putty from around the base of her refrigerator roof vent.  I tried using another set of tools for removing the stripped screw in the stop block on the bus to no avail.  I even managed to break off two drill bits in the hole I was drilling in the screw.  The more I work on this the worse it gets.

When Linda and Madeline got back Madeline had lunch and then laid down for her nap.  The three adults then had vegan hotdogs for lunch after which I put the finishing touches on my design drawings for the pull-out pantry.  Mara and I then went on an errand run.

Our first stop was the FedEx store in Novi where I made copies of all of the drawings for the desk and the pullout pantry.  We then stopped at General RV to return the refrigerator vent cover as it did not fit the base section on Mara’s roof.  They had a Camco cover that claimed it would work, and looked like it might fit, so she exchanged them and got a small credit.  When we got back at 3:15 PM Brendan and Shawna were already there.  They got Madeline up at 3:20 PM and stayed until about 4 PM.  After they left I got up on Mara’s roof to help with tasks there.

First we checked the refrigerator vent cover.  The mounting holes lined up but the flanges (shields) on the long sides were not wide enough to fit outside the base flanges.  The proper fit requires the upper flanges to be outside the lower flanges by at least 1/4″ so heat can escape and extend below the lower flanges to keep rain from getting into the refrigerator cavity.  I was going to install the 24″ x 24″ piece of thin sheet steel for the magnetic cell phone booster antenna when I discovered that the antenna would stick to the old satellite dish.  We experimented some more with the location of the inside antenna but could not improve on yesterday’s placement.  The performance was as good as with the metal sheet so I decided not to install the metal sheet.  Mara then caulked around the refrigerator vent base and touched up a few other spots around tank vent caps.

Linda grilled a variety of veggies for dinner.  I opened a bottle of Pinot Noir wine and we ate outside.  It was cloudy and 76 degrees F with light winds; very pleasant and bug free.  We had fresh strawberries with the meal and dark chocolate for dessert.  We eventually moved inside to chat but did not stay up late as I needed to be up early in the morning and on my way to Indiana.

 

2015/07/19 (N) Another Buddy Visit

Leave a reply

Linda was up at 6:30 AM to get showered before Madeline woke up at 7 AM.  Once Madeline was up they got busy right away making vegan blueberry pancakes.  I was up at 7:20 AM, got a quick shower, and was dressed and seated at the table just in time for breakfast.  The pancakes cooked especially well this morning although I would like to try them sometime without the blueberries cooked in.  After we were done eating I made coffee while Linda and Madeline prepared vegan sloppy Joe’s in the crock pot for lunch.

Mara has been getting up when she feels like it and eating breakfast by herself.  By 9 AM she was outside emptying the passenger side storage bays on her motorhome.  She spent the rest of the morning going through the stuff she had removed, deciding what to keep, organizing it, and putting it back.  I gathered up our laundry, sorted it, and started a load.

Aunt Meghan (our daughter) and Uncle Chris (her husband) arrived at 10 AM and I brewed another pot of coffee.  This was the second buddy visit of Madeline’s stay (the first was Cousin Katie on Friday).  Meghan provided a lot of child care during Madeline’s first 18 months and Madeline adores her “buddy.”  She took Meghan on a tour of the house showing her where various things, like snacks and kitty cats, were to be found.  It was a sure sign that Madeline is finally feeling very comfortable at our house.

Having other adults around gave Linda a break and some time to finish preparing lunch, although once Madeline realized Grandma Linda was at work in the kitchen she had to help.  I went out around 11:45 AM to fetch Mara.  We all sat down at noon and enjoyed a simple but delicious meal of vegan sloppy Joe’s (based on textured vegetable protein aka TVP), corn on the cob, raw baby carrots, and black grapes.

Madeline had very busy days yesterday and the day before and got up a little tired this morning so by 1 PM she was more than ready for her nap.  Meghan and Chris had things to do and took their leave.  Mara went back to work on her rig and Linda laid down for a nap.  I tended to the laundry and then went out to work on our bus and Mara’s motorhome.

I used the Speedout set to try and remove the screw with the stripped head from the stop block on the passenger side fixed glass frame.  I was not successful with this tool so I switched gears and worked on Mara’s cell phone booster system.  I climbed on the roof and she handed me the 12″ x 18″ thin galvanized sheet steel plate.  I took it to the front of the roof, set it down on the fore-aft centerline, and positioned the 4″ magnetic mount antenna in the center.  I dropped the coax over the edge by the driver’s side window and climbed back down from the roof.

Mara opened the sliding side window and screen by the driver’s seat and I passed the coax in to her.  Inside the rig we positioned the amplifier on the driver’s seat and started experimenting with various positions for the inside antenna.  We found one that worked well and left it for her to try.  I checked the laundry and then laid down for a nap.

I skipped dinner as I had a SLAARC meeting at 6:30 and had to leave before 6 PM which is when Madeline was having her evening meal.  Our ham radio club meetings start with social time from 6:30 to 7:00 PM.  The meeting was called to order at 7 PM by president Harvey (AC8NO) and I agreed to act as recording secretary.  Linda was not able to attend because she was taking care of Madeline so I gave the treasurer’s report in her absence.  The meeting adjourned at 7:10 PM.  We reconfigured the room for the program which was a presentation and debrief of our recent field day activity.  Larry (K8UT) reported on the N1MM Logger Plus networked computer logging software.  Steve (N8AR) reported on the radios and antennas and conducted the debriefing.

I got back home before 9 PM.  Madeline was asleep and the ladies were each enjoying a glass of Pinot Grigio on the back deck.  I poured one for myself and joined them.  The mosquitoes eventually appeared and we retreated indoors.  I reheated the bowtie pasta from the other night and finished it for dinner.  We said “good night” at 10 PM after which I checked e-mail and websites and then headed to bed.  I wrote for a while before turning out the lights.

 

2015/07/18 (S) RV Shopping

Leave a reply

Madeline was awake at 7 AM and Linda got her up shortly after that.  I slept in until 8 AM.  They had already eaten breakfast by then so I made coffee and had cinnamon raisin toast.  Metropolitan Baking Company makes a very tasty cinnamon raisin bread.  We all sat in the living room while Madeline played with various toys and I worked on finishing yesterday’s blog post.

Linda and Madeline left at 10 AM for the Howell Library.  The plan was to let Madeline play in the children’s area, which has a lot interesting things to do for children her age.  After selecting some books and DVDs to bring home they were headed to Meijer’s to do some grocery shopping.

I continued working on my iPad until Mara came in the house.  We had a chat about blogging and I showed her the Feedly app on my iPad.  She has attended workshops put on by The Geeks On Tour and has their training materials.  I think Blogger is probably the right tool for her and Picasa is probably the right way to manage her photos.  They are both Google products so they work well together and they are free to use.  There are downsides to that, especially for professionals, but for most people it’s a great solution.

Mara and I left around 11:45 AM and drove to General RV in Wixom.  This was my first visit to their new facility and it is nice.  The parts department is larger and better stocked than the old one and is bright with natural light from large south and west facing windows.  We were asked several times if we needed assistance but we were never pestered.  They did not have any of the white Dicor self-leveling caulk we were looking for but one of the employees checked their stock and brought out six tubes.  Mara bought four of them along with a new Norcold refrigerator roof vent cover, a small roll of Eternabond tape, and some concentrated RV wash/wax.  I picked up eight brown circular adjustable air vents for the bus.  The ones in there now are black but I think the brown will look better with the new floor tile.  We won’t really know, however, until we install them.

We drove to Lowe’s in Howell where I bought two pieces of 12″ x 18″ thin galvanized steel plate and three rolls of 3M double-sided tape suitable for outdoor use.  The plan is to put one of these on the roof of Mara’s motorhome and possibly put the other on the roof of our bus to allow the use of the magnetic base cell phone antennas that came as part of the weBoost Drive 4G-X cellular booster systems.  Once the steel sheets are affixed to the roof I will caulk around them.  First, however, I will just set the sheets up there and see what sort of difference the system makes.

We stopped at O’Reilly’s auto parts store and Mara bought some 10, 15, and 20 Amp mini fuses.  These fuses have a small LED that glows if the fuse opens.  They were more expensive than the regular ones, but that is a very handy feature and I may stock up on these the next time I need to buy fuses.

Back at the house Linda informed me that when the storm blew in it pulled the sun umbrella out of the table on the deck.  We put the glass top back in the table and re-installed the umbrella.  This has happened a couple of times and we have been lucky that the glass top has not broken.  Mara returned to her rig.  She had left her patio awning out but it was not damaged.

Linda got Madeline up from her nap at 3 PM and read her a story about flying in an airplane.  Madeline then played with her toys for a while.  Around 4 PM Madeline wanted to bake a cake.  Linda was planning on this anyway but it was nice that it was Madeline’s idea.  They got busy in the kitchen and I sneaked off to my office for a while.

Madeline had dinner at 6 PM so I came up from my office while she ate.  Meals are a social time and I was ready for a break anyway.  After dinner Linda helped Madeline get cleaned up.  I slipped back down to my office while they watched an Elmo DVD, but by 7 PM I was done working on the pantry design for the evening and went back upstairs.  Linda was reading the airplane ride book (again), after which Madeline played (with) the organ after which they drew for a while and then played with the Play-Doh.  Madeline is a busy girl.

I was just getting ready to go ask Mara what temperature to preheat the oven when she came to the house with an armful of ingredients for the pizza.  She has a recipe for a wheat-free (gluten-free) pizza dough that she wanted us to try.  It calls for cheese and eggs so to make it vegan Linda had her buy Daiya mozzarella shreds and gave her egg replacer to use.  The other ingredients include almond meal, chickpea flour, golden flaxseed, onion powder, garlic powder, sea salt, olive oil (EVVO), and water.

It took another 25 minutes to get Madeline to bed but once Linda had her tucked in I opened a bottle of Nebiola wine from the St. Clair Winery in Deming, New Mexico.  I often write that I am not a fan of red wines and continue to not like dry wines with lots of tannins.  The Nebbiolo, however, is one of the nicest wines I think I have ever tried.  That probably means it is too sweet for most red wine drinkers, but I did not find it to be sweet; I found it to be smooth and complex.

We ordered a couple of things from Amazon on Wednesday and they showed up yesterday.  When I unboxed the Notier capacitive touch screen precision stylus I was surprised by what I found.  It’s a 2-part housing that unscrews and the cover screws onto the other end of the bottom part, which is needed for comfort and balance.  The stylus tip is small but has a 1/4 in clear plastic disc on the end.  It was on sale for $11 and I decided right away I would not return it.  Besides, I had not actually tried it yet.  So I finally tried it while the pizza was cooking.  It is an amazing little device!  It is, indeed, very precise and works with a delicate touch so I will have to re-calibrate my “typing” style, but it just goes to show that you never know until you try.

I lost track of time but it was somewhere between 9:30 and 10 PM when the pizza was ready to eat.  It was, however, worth the wait and might be the best vegan pizza I have ever had.  The recipe is definitely a keeper.  We each had a chocolate cupcake (with sprinkles) while we finished our wine.  We then adjourned to the living room and talked until almost 11 PM.  It was a very full day for all four of us and everyone was tired but satisfied.  It’s nice having family and friends here.

 

2015/07/17 (F) A High Pressure Situation

Leave a reply

We closed up the house yesterday and turned on the air-conditioning as the forecast for today was upper 80’s with humidity to match and the forecast for tomorrow is a high of 90 with very high humidity.  Linda did not sleep well again last night but that had nothing to do with the air-conditioning.  The sites where the dermatologist had removed things itched, which did not help.  Nonetheless, we were both up by 8 AM and, as usual, I made coffee and we had granola.  I prepared a travel mug of coffee and left at 9 AM for Chuck’s bus garage in Novi.  Brendan, Shawna, and Madeline were due to arrive at 10 AM and I wanted to be back as close to that time as possible.

As I was working on the design for the pull-out pantry yesterday it became very clear that I needed more accurate measurements of various details of the new refrigerator in order to make sure the doors could open and the pantry could slide in and out.  It was a good thing that I checked as the measurements were not exactly as published and the specifications did not show exactly where the doors were hinged or how much clearance they needed to swing on the hinges.  Now I know, and it is a bit more than I originally allowed for, so it was a good thing that I checked.

I got home at 10:15 AM and the trio was already there.  Mara emerged from her rig a few minutes later and joined us.  Brendan and Shawna stuck around for a while but not long enough to get Madeline down for her 1 PM nap.  They had been talking to her all week about staying with Grandma Linda and Grandpa Bruce and she was prepared.  She was busy playing with Linda and did not seem concerned when her parents left for a music festival in Chicago.  They will retrieve her on Monday.

Our older grand-daughter (and Madeline’s cousin), Katie, arrived around noon so Madeline had one of her buddies here.  Madeline enjoyed her lunch and voluntarily laid down for her nap.  Katie signed up to sell Cutco cutlery and accessory products and asked if she could come practice her sales pitch on us.  We had agreed to let her do this, of course, and Mara joined us by her own choice.  The selling involved a lot of demonstration and use of a few of the knives in side-by-comparison with our existing knives, some of which were already Cutco brand.  Linda ordered a pair of kitchen shears and a santoku trimmer knife.  Mara also ordered a pair of shears and Katie was able to throw in a birdsbeak paring knife which Mara will get as Linda has one.  They agreed to just split the cost of the total order in half.

Mara was anxious to work on the roof of her Bounder and it needed to be cleaned before it was caulked.  It was a hot, humid afternoon and pressure washing the roof seemed like the perfect use of such an otherwise miserable day.  I got out the pressure washer and hose and got it hooked up.  Mara put on her bathing suit and we both climbed up on the roof of her motorhome.  I adjusted the spray nozzle to a fan pattern that would clean from 12″ away without damaging anything, showed her how I would approach the job, and left her to do the work.  Actually I sat in the shade on the porch, offered helpful advice, and occasionally moved the pressure washer.

Madeline finished her nap while we were working and came outside several times with Linda to see what we were doing.  She and Linda walked around the back yard and saw geese and a snake.  They also saw a young deer from our bedroom doorwall.  Our home in the country is a different and exciting place for her as it is for us.

When Mara was done spraying off the roof I sprayed off the sides of the rig to rinse off the dirty water that had run down the sides.  Mara then put out the patio awning and I sprayed off both sides of it as well.  When we were done we got the hose off of the grass and put the pressure washer back in the garage.  Mara was very pleased with what she accomplished.  Not only did she get something done that needed to be done but it was another thing she took care of herself instead of paying someone else to do it.  I get that.

I worked some more in my office and then came upstairs for dinner.  Mike (W8XH) had called and confirmed that Steve (N8AR) was expecting us at 8 PM.  I left at 7:30 PM and drove to Steve’s place southwest of Howell.  Mike and I arrived within a couple minutes of one another and were there for a little over an hour.

Steve is a PhD electrical engineer who worked for Bendix and was involved in communications projects for space programs.  He has a lot of test equipment that you will not find in most ham shacks and he knows how to use it.  In this particular case he used his Hewlett-Packard Network Analyzer to do two-port radio frequency through-measurements of my two Morgan Manufacturing lightning arrestors.

The first thing Steve noticed was that the center contact on one of the N-female connectors was spread open a bit.  Unfortunately any spread is “a bit” too much.  At radio frequencies these contacts need to be tight.  We crimped the contacts back together as best we could so we could proceed with the testing, but Steve strongly suggested that I replace them with high quality parts.  As expected, based on my operating experience, the M-302N V/U arrestor did not look good when tested.  Steve captured the resulting return loss graph and put it on a thumb drive for me.  I will e-mail it to Morgan with a cc: to KF7P Metalwerks and request a new one.  If the new one isn’t any better I will request a refund.  I should not have to rebuild stuff like this and the poor performance may be a design flaw rather than a manufacturing defect.

When I got home around 9:30 PM Linda and Mara were still up and chatting away in the living room.  I joined the conversation until they both decided to retire for the evening.  I spent a few minutes in my office after that taking care of e-mails and then went to bed.  I wrote for a while but was too tired to concentrate and went to sleep.

 

2015/07/16 (R) RV Work

Leave a reply

We were up at 6 AM and by 6:25 Mara had started the engine of her motorhome to pull in the slides.  She disconnected the electrical cord and we helped her back out of the driveway at 6:40.  She was pointed west so she had to drive to the end of our street and use the circle to turn around.  Her destination was Cummins Bridgeway in New Hudson.  When she made the appointment they said the closer to 7 AM she could arrive the better.  They estimated she would be there 3 to 4 hours.

Mara's Fleetwood Bounder parked in our pull-thru driveway.

Mara’s Fleetwood Bounder parked in our pull-thru driveway.  Linda in green jacket, Mara in red.

Linda did not sleep well last night, a common side effect of eating too much too late in the evening, and went back to bed once Mara was safely on her way.  I decided to stay up and clean the coffee maker before making coffee.

I wiped out the upper housing and cleaned the nooks and crannies with Q-tips.  The upper housing is undoubtedly designed the way it is to make it structurally adequate with a minimum of plastic but it was equally obviously not designed with any consideration for being able to clean it.  Like many things, it leaves me wondering if the designers ever use the products they design or what sort of functional specifications they work from and who develops those.  I think the Bauhaus had it right when they declared “form follows function.”  My guess is that commercial equipment, while less “stylish” than consumer goods, has cleanability and serviceability as primary design considerations.

I remembered that we had a one gallon jug of distilled white vinegar in the bus so I got that and ran eight cups of it through the coffee maker.  I added four cups of water to the used vinegar and ran it through again.  I then ran 12 cups of RO water through the coffee maker.  By the time I was done it was approaching 8 AM so I ground up some of the Sumatra Mandheling beans (not decaffeinated) and made seven cups of coffee.  I normally make 8 – 9 cups but this was full-strength stuff.  I’ve been making 11 cups while Mara is here but it turns out that she does not drink much coffee so I will be back to my usual 8 – 9 half-caff servings going forward.

I enjoyed my first cup of coffee while finishing yesterday’s blog post and starting this one.  I enjoyed my second cup while researching hardware for mounting a small table to a wall so that it is essentially cantilevered, which is the table arrangement we need for the bus.  I found a 2-piece aluminum extrusion that might be the solution for attaching the table to the wall.  It is 30″ long and can be cut to length but I do not think it will not be strong enough by itself to support the table.  I found an angle bracket on Rockler that might be the additional piece I need.  It is 12″ x 18″ with a notched corner, made of 1/8″ steel, and powder-coated black.  A pair of them will support 1,000 pounds so one in the center would be more than sufficient.  An alternative would be a wood strut angling back to the wall but we are not willing to have a vertical table leg.  I have not decided whether the table should be removable but I am leaning towards a more permanent installation.

Linda eventually got up but neither of us were hungry so we did not have breakfast.  I went to my office and ordered the ZioTek monitor mounting system from CyberGuys.  I then e-mailed Ewa at AFC Industries and thanked her for the second quote but let her know that the price was way out of my budget.  I finally settled in to work on the custom desk design for the bus and eventually finished it (I think).  Linda left around 12:30 PM for her dermatology appointment.

Now that we have base station antennas cabled to the ham shack I tend to have the new Yaesu FTM-400DR/DE dual band (VHF/UHF) radio on whenever I am working in my office.  It provides a pleasant diversion from my other tasks and is actually useful.  Somewhere mixed in with everything else were a couple of QSOs with ham buddies and an attempt to coordinate with Steve (N8AR) and Mike (W8XH) about testing my two Morgan lightning arrestors at Steve’s QTH.

This toad was sitting on a rock by our front porch.

This toad was sitting on a rock by our front porch.

Our bus had settled in the rear and was clearly out of level.  The reason it had settled was that I forgot to switch the suspension system to Level Low and shut off the air to the engine accessories.  It was of no consequence but it bugged me so I started it, let it air up, re-leveled it, shut it down, and switched off the batteries and engine air accessories.

Mara returned from Cummins Bridgeway around 1 PM and I guided her back into her parking spot.  They did the routine service on her motorhome engine and generator but found several things on the genset that needed to be repaired.  She agreed to have the work done so they removed the genset from her rig and will reinstall it next Wednesday.  They also inspected the motorhome and gave her a list of other things that needed to be fixed, some right away and some eventually.  She did not have them do any of that work as she wanted me to look at the list first.  The added service work means Mara will be visiting with us for at least another week, which pleased us greatly.

I went over the list with her and we discussed the relative importance and urgency of each repair.  One of the items involved the caulking on the roof so we both climbed up there to have a look.  I also wanted to scope out how we might install her weBoost Drive 4G-X cellular booster system.  While we were on the roof I was able to rock the rig side-to-side quite a bit just by shifting my weight.  One of the other items on the diagnostic list was shock absorbers and I indicated that I thought that sounded appropriate, especially given that the back ones reportedly had cracked/broken mounts.  They also noted that the transmission fluid was low and that the filter and fluid should be replaced.  I encouraged her to have these taken care before she left as Cummins Bridgeway is a very good service facility.

The other items were things that could wait but the caulking of the roof was something Mara could do herself.  She likes to take care of as much of her rig as possible and she will be here through at least Wednesday, so she has time.

Linda got back from her out-patient surgical appointment with bandages in seven different places.  We visited for a while and then I left the ladies and returned to my office.  I started on the design of the pull-out pantry for the bus and quickly realized that the very expensive Fulterer heavy-duty pull-out pantry slide I ordered from Rockler was too wide for the space we have available.  I came upstairs and groused about it for a while until Linda and Mara urged me to try canceling the order.  I called Rockler and spoke to someone in customer service.  I won’t know until tomorrow at the earliest, and probably not until Monday, if I was successful in intercepting the order before it shipped.  If not I will have to pay to ship it back and may have to pay a restocking fee.  Although I do not have anywhere else I can use it at the moment, between the restocking charge and the cost of shipping I may just keep it and find a use for it.

Linda made a large salad for dinner and we chatted during and after the meal.  It had been an early, long, hard day for all of us.  Mara returned to her rig before it was dark and Linda headed off to bed shortly thereafter with me not far behind.

 

2015/07/15 (W) Prime Wednesday

Leave a reply

It was brisk when we got up this morning, with the temperature in the upper 40’s (F), light breezes, lower humidity, and clear, blue skies.  When the weather in Michigan is at its best it is near perfect.

After our usual coffee and granola we spent a little time browsing Amazon.com looking at their “Prime Wednesday” sale.  Neither of us are compulsive shoppers or impulse buyers and scrolling through thousands of items on a slow Internet connection looking for something we can’t live without at a price we can’t pass up is not our idea of fun.  I have things I need to order, like the multiple monitor mounting system for the ham shack, but it quickly became obvious that I was not going to find those items for sale as part of Amazon’s special July 15 Prime Sale.

Mara was up and took her garbage to our trash to can and returned to her rig.  Linda then took our garbage out and moved the can to the street.  By 10:30 AM Mara had not yet emerged from her rig, so I went to my basement office and resumed work on the custom desk design for our bus.  I still need to design the pull-out pantry but I finally ordered the Fulterer top/bottom slide mount from Rockler and had it shipped directly to Jarel in Logansport, Indiana.  It is a serious piece of hardware that will support 450 pounds, so it should be more than adequate for the task.

Mara eventually emerged from her rig and the ladies left for 12 Oaks Mall and Mara’s first ever appointment with Renee in the J. C. Penney’s Salon.  They were gone quite a while, tacking on several stops at pet and food stores before returning home.

I received a second quote for a wall-mounted monitor mounting system from AFC Industries.  It included itemized pricing and an offer of a 15% discount but was still way too expensive.  Though more expensive than a desk-mounted pole system I decided I to order the ZioTek wall-mounted monitor mounting system from CyberGuys.  Being wall-mounted it will get my monitors completely off the desks, leaving room for ham radio equipment to slide underneath and all the way to the back edge of the desk (and beyond).  It will also isolate the monitors from the desk so they won’t move if the desks are bumped.  Another bonus is that I can move the desks to get to the cables at the back of the radios without having to move the monitors.

The monitor mounting system is a significant purchase so I wanted to make sure the components would work the way I need them to.  I measured the three monitors that will initially be mounted using the system and then made a scale drawing to see how they would fit.  I added all of the items to the shopping cart and was getting ready to complete the purchase when I noticed that a 5% discount was available if I joined their e-mail club.  I signed up, received an e-mail, and confirmed my intention to join but the 5% discount did not show up in my shopping cart.  I called the 800 number and was told it would take 24 hours for the discount to be available so I cleared all of the items out of the cart and will re-enter them tomorrow.

I finally settled in to my design work but took several breaks to talk to friends on the Novi and South Lyon repeaters.  The Morgan Manufacturing VHF/UHF lightning arrestor was once again degrading my signal to an unusable level/quality so I once again disconnected the antenna and radio coax and joined them together with an N-female to N-female barrel adapter.  Once I did that I was able to transmit and receive to/from both repeaters full-quieting.

I exchanged a couple of e-mail updates with Jarel Beatty, the cabinet maker in Logansport, and finally quit working around 5 PM.  I came upstairs and found that the weBoost cellular booster systems had arrived from Amazon so I unpacked the shipping box and opened them.  I had not realized when we ordered them that they were designed for use in a car with an inside antenna that requires the phone or other cellular device to be 18 – 36 inches away.  That is not very far and it is a fairly small range.  As the name implies, however, it is designed for use while in motion which is what both we and Mara need/want.  I decided to temporarily install one of them in Linda’s car to test it.

Sitting in the driveway in a relatively bad location my phone was in 3G mode with a weak, but usable, signal that hovered around -115 to -118 dBm.  With the booster turned on my phone switched to 4G-LTE and the signal strength improved to anywhere between -103 to -94 dBm.  (The less negative the signal strength in dBm the stronger the signal.)  That may not appear impressive on the surface, and it was certainly not the 50 dBm gain that is claimed for this device, but it was actually a significant improvement.

“dB” is the abbreviation for “decibels” which is a logarithmic scale.  Logarithmic scales are useful for representing quantities that vary over a large range, like cellular signal strengths.  A change of 3 dB represents a factor of two, i.e., a doubling or halving of the quantity.  Thus a change from -118 dBm to -115 dBm (decibels to a millivolt) represents a doubling of the received power.  It is still a weak signal, but it is twice as strong.  Going from -118 to -103 is a change of +15 dBm and is five doublings (-118 to -115 to -112 to -109 to -106 to -103) which is an increase of 2x2x2x2x2 = 32 times.  Continuing from -103 to -94 is another +9 dB change representing three more doublings (-103 to -100 to -97 to -94) for a total gain of 32x2x2x2 = 32×8 = 256 times.  Starting from a signal in the -118 to -127 dBm range that is potentially the difference between useable and not useable.  (BTW:  a change of 10 dB is a factor of 10, so going from -115 dBm to -105 dBm and then to -95 dBm represents an increase of 100 times.)

We had decided at dinner last night that we wanted to go to The Blue Nile restaurant while Mara was here.  The best time to go turned out to be this evening, so Linda made an online reservation for 7:30 PM at the Ann Arbor location (there is also one in Ferndale).  We tested the weBoost Drive 4G-X cellular booster on the drive to/from Ann Arbor and it definitely made a difference in the signal strength we saw on our phones.

It wasn’t until we got part way down Main Street that we realized that today was the opening day of the Ann Arbor Art Fair.  The last place I wanted to be driving, parking, or walking was at the Ann Arbor Art Fair, not because I dislike art (we love art), and not because I dislike art fairs, but because I dislike congested traffic and crowds, which the AAAF has in abundance.  Surprisingly, we were able to park in one of the parking structures a couple of blocks from the restaurant.  After fighting our way through the pedestrian traffic I was even more surprised to find the restaurant essentially empty.  The Blue Nile is slightly outside the portion of Main Street where the AAAF takes place and streets to either side that are closed off to vehicles during the AAAF.  All of the restaurants and the beer/burger joints in and around the AAAF venue were doing a brisk business, especially if they had outside seating (it was a very pleasant evening), but the restaurant was open and the host was very gracious.

The Blue Nile serves Ethiopian cuisine.  Some of the tables are upside down rope baskets with four chairs and two side tables.  We always ask to be seated at one of these because we always order the Vegetarian Feast which is, in fact, vegan.  The Feast comes on a large round tray covered with a layer of Ethiopian sponge bread (made from teff flour) with small piles of the seven different vegetable-based dishes on the menu surrounding a pile of (optional) salad in the center.  Beverages and platters of rolled up sponge bread are placed on the two side tables (we had water and Ethiopian spiced tea).  The meal is eaten by tearing off suitable sized pieces of sponge bread and picking up the eight different selections from the tray.  Before the food was brought to the table we were given hot, moist towels to wash our hands.  Nice touch.

The food was amazing and the experience somewhat more communal than sitting at a standard American table and eating with utensils.  The waitstaff was gracious and attentive and it was a wonderful experience for all three of us.  Mara asked one of the waitstaff to take a picture of the three of us, which they gladly did.  She then uploaded it to her Facebook page along with a brief description of her visit and meal.  One the drive home she already had 12 “likes.”  This is the side of Facebook, and other social media, that is fun.

It was getting dark by the time we got back to the house but we took the time to unload Mara’s kayak from its special mount on the rear of her motorhome that is installed in the tow receiver.  The kayak mounts diagonally from the lower driver side up past the roof on the passenger side and the tip is about 13′ 2″ above the ground.  She was leaving at 6:30 AM the next morning to drive to Cummins Bridgeway to have her main engine and genset serviced and would be traveling south on Hacker Road to Grand River Avenue.  The last time we did this we clipped a branch in the southbound lane on Hacker just north of Bendix Drive not far from Grand River Avenue.  I was concerned that she would catch the same branch and damage her kayak which is why we took it off the rig.

Once the kayak was off the back of her rig and sitting in our yard we said a quick “good night” and all trundled off to bed as 6 AM would come all too soon.  I wrote for a while in bed but was too tired, and full of food, to stay awake.

 

2015/07/14 (T) Red Chili Wine

Leave a reply

Storms moved through the area overnight with more lightning and thunder than rain, or at so it seemed.  The storms were triggered by a cold front, behind which we had a cloudy day with periods of rain.  Linda was up at 7 AM and read quietly until I got up at 8.  I made a full pot of coffee (Cafe Europe half-caff blend from Teeko’s) and then joined her in the living room.

Linda was checking Dr. Michael Gregor’s speaking schedule and saw that he will be at Wayne State University in December and will be one of the keynote speakers for the 2016 Holistic Holiday at Sea vegan cruise.  We have not heard him speak in person, and will not be here in December, so that would be another reason to go on the cruise again.  By 9:45 AM Mara had not emerged from her rig so we went ahead and had breakfast.  Linda then went for a walk and I went to my office and worked on the design of the custom desk for the bus.

Mara finally emerged at 10:30 AM and we chatted for a while until Linda got back.  Our chat was briefly interrupted by a call from Mike (W8XH) on the Novi repeater so Mara got to see ham radio in operation.  My reception was weak and noisy and according to Mike my transmitted signal wasn’t any better.  The only thing that has changed since we tested this late last week is that I got the repaired M-302N VHF/UHF lightning arrestor back from Morgan Manufacturing yesterday and re-installed it.  Mike is going to help me do some more testing, but I am rapidly coming to the conclusion that these units are defective by design and I will have to replace them with something else.  I am disappointed to say the least.

It was another cool, cloudy, rainy day, just the kind of day for staying inside and getting stuff done.  Linda and Mara both had things to do and settled in at the dining room table to work.  Mara has been focused on planning her upcoming travels and spent much of the day making reservations.  Linda worked on the bookkeeping for our GLCC chapter and SLAARC ham radio club (she is treasurer of both).  She also renewed our Coach-Net emergency road service and our Harvest Host membership, which had expired, and probably took care of a lot of other things that I don’t even know about.  Except for an occasional break I worked on the custom desk design until 6:30 PM.  On one of those breaks I needed to measure something in the bus so we gave Mara the inside tour.

When I came upstairs Mara was taking advantage of the unlimited hot water available in our guest bathroom to have a nice long shower.  We know from personal experience what a luxury it is to take such a shower when living in an RV.  Linda had started preparing our dinner so I opened the bottle of Hatch Red Chili wine.  This wine, from St. Claire Winery in Deming, New Mexico is one of the more unusual wines we have ever had but we really like it.  It is a slightly sweet red wine with no tannin, a hint of chili flavor, and heat in the back of the throat on the finish.  We had vegan mock Italian sausages with sautéed onions and red peppers and the wine went well with it.  I had mine on a hotdog bun with mustard.  Mara had another serving of her beef stew, which she is trying to use up, and Linda put out a plate of whole, fresh strawberries.

One of the nice things about having visitors is that meals take longer to eat as we linger at the table in conversation.  Mara returned to her rig around 9 PM to have some quiet time with her cats before going to bed.  Linda decided to watch a couple of TV programs and I went back to work on the desk design.  I called it quits around 10:45 PM and went to bed to work on this post.  The overnight low is forecast to drop into the upper 40’s which should make for excellent sleeping.

 

2015/07/13 (M) weBoost

Leave a reply

Linda got up before I did and went for a long walk.  I was up by the time she got back and made a full pot of the Sumatra Mandheling coffee I just got from Teeko’s.  Mara eventually joined us for coffee and then breakfast.

Mara wanted to get the engine and generator serviced in her Fleetwood Bounder motorhome and asked for recommendations in the area.  There were three relatively convenient options but we had her contact Cummins Bridgeway in New Hudson, in part because she has an Onan (Cummins) generator and in part because we took our Itasca Sunrise motorhome there and were always pleased with the quality of the service.  They said they could take her on Thursday and she set up the appointment.  They estimated three to four hours so she plans to wait for it.

Mara was also interested in a mobile cellular booster for her motorhome, and I have been planning to get one for several years, so we researched the current offerings online.  At one time Wilson Electronics practically owned the mobile booster market.  They have more competition now and their consumer systems have been rebranded “weBoost.”

After scanning what was available we focused in on the weBoost Drive 4G-M and Drive 4G-X.  I downloaded the PDF manuals for each of them and studied the specifications. I don’t care about the marketing hype.  As they used to say on Dragnet “the facts mam, just the facts.”  Both units are 5-band, multi-mode units designed for in-motion use and the specs were very similar, but not identical.  The MSRP on the X model was almost $100 more than the M model so I called Cellular Solutions and talked to Judy.  In practical terms, she said the X model would work with weaker signals.

I was prepared to order two of them but they did not have them in stock at their Sanford, Michigan location.  She thought she could have them to us by Friday but that was not soon enough and we did not want to pay $30 for 2-day shipping on top paying almost $30 in sales tax (for each unit).  So we did what we always do, we checked Amazon.  Amazon had four of the weBoost Drive 4G-X systems so I ordered two of them with Prime 2nd day shipping of $4.99 each and no sales tax.  They are scheduled to arrive on Wednesday July 15 which will give us enough time to get them installed.

The installation on both rigs will require me to attach a steel plate to the roof to act as a base for the small 4″ tall magnetic mount outside antenna.  On our rig I will probably put the antenna up front and screw the plate to the existing aluminum plate, using putty under all the edges and the screw holes, and then caulk around the edge and the heads of the screws.  The cable will come in through the front weatherhead.  On Mara’s rig I will see if I can route the cable through the refrigerator roof vent or the roof-mounted air-conditioner cover.  The route will determine the placement of the steel base plate.

Linda made an appointment for Mara with our hairdresser, Renee, at the J. C. Penney’s salon at 12 Oaks Mall for Wednesday at 1:30 PM.  By the time we had accomplished all of this it was early afternoon and time for a light lunch.  After lunch Linda and Mara went for a long, vigorous walk and I retreated to my office and worked on the custom desk design.  I e-mailed Jarel to see if he would be available on Thursday.  He e-mailed back that any day but Thursday would be OK, so I may go Friday but more likely it will be next Monday.   I thought I could have the design done by Wednesday bedtime, but it would have been a push and I did not want to rush the process and risk making a mistake.  As much as I hate to delay this until next week I may have to.  Mara may leave on Friday, or delay until Saturday or Sunday, and I want to be hear when she leaves.  Meanwhile, Madeline is coming to stay with us on Friday and will be here until Monday.  These are indeed busy times.

I came back upstairs just before 5 PM and found the ladies sitting in the shade at the east end of the deck.  Mara was busy using MapMyPlaces to plan the next leg of her travels from our house to Quebec City, a trip of just under 1,000 miles.  I got a couple of ice cold beers (Linda did not want any) and we sat and talked until Mara returned to her rig at 6:30 PM to tend to her cats and have an hour of quiet time before dinner.

We got back together at 7:30 PM for dinner, which consisted of leftovers plus a simple salad for us.  Dinner led into a long discussion about health and nutrition.  We talked about the Holistic Holiday at Sea vegan cruise, which usually takes place the first week in March, and the vegan summer fest that takes place each July in Pennsylvania.  Mara seemed interested in both and thought she might be able to get her friend, Michael, to go on the cruise with her.

The more we talked the more we thought we might like to go again.  The last time we went, in 2013, we researched places where we could board the cats.  The only place we found that looked any good was in Punta Gorda.  Punta Gorda is quite a drive from Ft. Lauderdale, but it is not that far from Arcadia where we will be parked for January and February.  It would be easy to take the cats there and then drive to the Port of Miami to catch the ship.  However, if Mara goes on the cruise we might have another option.  When she has to leave her rig for a while, such as her recent trip to Belgium, she flies her sister in from California to house and cat sit.  She assured us that “sis” would be happy to take care of our cars as well.  All that would be required would be for us to have our motorhomes at the same RV park.  That could be Big Tree in Arcadia (since we would already be there) or someplace near Miami (if we could both get in).  Adjacent sites would be nice, but not necessary.  I have no idea if we will do this, but it was fun to consider the possibility.

 

2015/07/12 (N) Mara Comes To Visit

Leave a reply

When I shut down the bus yesterday I forgot to shut off the air supply to the engine accessories and turn off the chassis batteries, so I did that as soon as I got up this morning.  I then made coffee and we had our usual juice and homemade granola.  After breakfast Linda went shopping and I went to Lowe’s.  She picked up a lot of fresh vegetables at the Howell Farmers Market and finished up at Meijer’s.  I bought a 4-piece screw extractor set and then stopped at O’Reilly’s and bought two gallons of 50/50 pre-mixed universal antifreeze to top up the Aqua-Hot in our bus.  I stopped at Teeko’s Coffee and Tea and had them roast a pound of Sumatra Mandheling beans.  We have not tried these before but Mary thought we would like them.  They are not decaffeinated, but we try to keep a regular coffee bean on hand for company, after dinner, or when we want (need) the high octane in the morning.

Linda had been in contact with our friend Mara for the last few weeks so we knew that she might stop here on her way to the Canadian Maritime Provinces.  Late last week she confirmed that she would be here on Sunday so after our morning errands we turned our attention to getting ready for her arrival.  She lives/travels in a Fleetwood Bounder (Class A motorhome).  We saw it in Quartzsite, so we knew it was somewhere between 35 and 40 feet in length and that she does not tow a car behind it.  Yesterday we moved our bus so she could park on the level pad with easy access to our 50 Amp electrical hookup.  I cleaned up the coaxial cables that I had spread out all over the rec room floor and Linda vacuumed the carpets and wood floors and cleaned the bathrooms.  We keep a clean house but it is not always tidy as we are involved in a lot of projects at the moment.  But when company is coming we like things to a least start out tidy.

Mara was coming from Michigan City, Indiana so she only had 200 miles to travel.  Most of it would have been on Interstate highways but she decided to detour over to Three Rivers, Michigan to visit a Latvian community located nearby.  She finally arrived at our house around 2:30 PM.  We met her in the street and I directed her into her parking spot.

It’s always exciting, and a bit intense, to meet up with an RV friend and that was certainly the case here.  Mara had enjoyed her stop at the Latvian community even though she found them in church.  We had last seen her in Quartzsite, Arizona in February.  We had all had a lot of RV travel adventures since then, and it was also her first visit to our house, so we had lots to talk about.

Linda made bow-tie pasta with mushrooms, onions, garlic, sun-dried tomatoes, and basil pesto using basil that she grew on our back deck.  We had a simple green salad and Italian bread with the meal and enjoyed 1-1/2 bottles of the 2013 Egri Merlot between the three of us.  We sat on the deck enjoying the last of the wine until it cooled off and we went inside.  By 9 PM we were all tired but we insisted that Mara stay for fresh sweet cherries.  Rejuvenated by the cherries we all got our second wind and had a long conversation about RVs, cellular and Wi-Fi communications while traveling, and a cool routing app that Mara uses (MapMyPlaces).  By 11 PM we were all tired for real and Mara returned to her rig for the night.  It had been a long, but very satisfying, day for all of us.

 

2015/07/11 (S) Impactful Tools

Leave a reply

We had a small crowd for our SLAARC breakfast this morning but good conversation.  After breakfast we drove to Chuck’s house and picked up the manual impact screwdriver.  Barb was up in the thumb visiting her brother-in-law who recently lost his wife (Barb’s sister).  We lingered for a while and then left for home, stopping for gas on the way.

Back at the house I started a load of laundry and then went to work on the stop block screws.  Linda helped steady the ladder and pass tools and parts back and forth.  I got three of the four screws out of the two stop blocks but the head stripped on the forth one so I was only able to remove the aft stop block.  I tried different bits and even tried drilling a small hole in the center of the head to allow the bits to go in farther but it did not work.  The next approach will be a screw extractor, but first I have to go buy one.

We had soy yogurt for lunch with red grapes and I had a few pretzels with roasted red pepper hummus.  I kept trying to get to the basement to work on the desk design but kept getting detoured.  Once I finally reached my office I found that the mouse trap that I had placed under one of my desks was out in front of it.  The food was gone but there was no mouse, only mouse poop.  I realized that the trap was upside down which allowed the door to swing open.  Our best guess is that a mouse was trapped and the cats pulled the trap out from under the desk and accidentally turned it over while pawing at it trying to get the mouse.  Since there was no sign of a mouse having been caught by one of the cats my best guess is that it escaped, for now.

I checked e-mails and found the one with the credentials and instructions for the QTH.com web-hosting of SLAARC.com so I shared those with the other members of the SLAARC website team and then logged in to check out the log file I had created the other day as a test.

I decided to reconnect the Yaesu FTM-400 radio to the Diamond X-50 antenna on the tower so I could monitor the Novi and South Lyon repeaters while I worked in my office.  I had quite a mess on the ham shack desks and decided the best way to deal with it was to install Mike’s Icom IC-2820H in my car in place of our Icom V-8000 2m rig.  At least that would get the 2820 off the desk.  I checked that the mounting brackets and they were identical so I removed the V-8000 but left the mounting bracket installed in the car.

Mike had modified the power cord on his radio by cutting off the T-connector and replacing it with Andersen PowerPoles so I had to modify the power cable in my car to match as I could not modify Mike’s radio.  I removed the fuse from the positive (+12VDC) lead and then cut off the T-connector, leaving about 6″ of wire so I can add PowerPoles and make it into an adapter cable.  I brought my Hakko soldering station up from the basement, set it up on the floor behind the center console, ran an extension cord from the garage, and used it to solder PowerPole contacts to the two wires.  I then inserted them into the black/red housing pair and snapped them in place.

I mounted the IC-2820H, connected the power cable and connected the coax from the antenna.  I reinstalled the fuse in the positive lead, started the engine, and turned the radio on.  A couple of hams were chatting on the Novi repeater, one of whom I knew (Jim, KB8TAV).  When they finished I gave Jim a call and he came back to me, the first time I have been able to use the Novi 440 repeater from my car.  Jim signed off and I switched to the South Lyon 2m repeater and gave a general call.  Steve (N8AR) came back to me and we had a short QSO that verified the radio/antenna was also working on 2m.  As we were wrapping up Linda started fixing dinner.

Linda fixed a simple salad and Dr. Praeger’s vegan hamburgers with Daiya non-dairy cheese.  These patties were also squishy rather than firm and, like the ones at Zingerman’s Roadhouse the other night, where not very satisfying.  They tasted OK, and we ate them because we are not inclined to waste food, but there is a lot more to what makes food satisfying than just taste.  Sight, smell, and texture (mouth feel) are also important.

Linda had several TXT messages from Mara letting us know that she would be arriving tomorrow sometime before 2 PM as she wanted to watch the Wimbledon finals at that time.  Linda and I considered how best to accommodate Mara’s motorhome and finally decided to just pull our bus straight forward until the nose was at the edge of the concrete driveway.  That created more than enough space on the level part of the pull-through driveway for her to park and plug in to our 50 amp service.  The only loads we have in the bus at the moment are battery chargers so we used our 15 amp cord to plug it into a garage outlet.  Since I had to start it to move I switched it to high idle once I had it positioned, leveled it, turned on the OTR air-conditioning to put a load on the engine, and let it run for 30 minutes.

I returned to my office after dinner and work on the desk design for a while but by this point I was tired and not really in the mood.  The last time I updated the BCM page on our website was after the February 2015 issue came out.  I have had articles in the March, April, and May issues and will have articles in the June and July issues.  I captured the covers from March, April, and May and updated the page.

I exchanged e-mails with several people and spent some time looking at dual and triple monitor stands on EBay.  We rarely use EBay and the site made me change our password before it would let me log in.  There was a large selection of products but none of them were exactly what I am looking for.  There wasn’t any rush so I decided to revisit this tomorrow.